Download Dacor REMP3 Specifications

Transcript
Installation Planning
Model
No.
A qualified technician must complete the
installation of this appliance.
Carefully check the location where the remote
blower is to be installed. The remote blower
should be placed for convenient access. Make
certain that electrical power can be provided in
the selected location.
Plan the installation so that all minimum
clearances are met or exceeded. Dimensions
shown provide minimum clearances, unless
otherwise noted.
ILB8
10 5/8” (270mm)
10 1/2” (267mm)
ILB10
12 5/8” (321mm)
12 1/2” (318mm)
Overall Chassis
Length “C”
Duct Diameter
“D”
8” (203mm)
5” (127mm)
10” (254mm)
ILB Overall Dimensions
Model
No.
ILB10
Electrical Supply
Requirements
Maximum
Duct Length
Refer to Ventilator
Specifications
Max. 60
Equivalent
Straight Feet
Total
Connected
Load
Blower
Rating*
Approximate
Shipping Weight
0.1kW (1A)
500 CFM
15 lbs.
0.2kW (2A)
900 CFM
18 lbs.
ILB Specifications
All dimensional tolerances are
+ 1/16”, - 0” unless otherwise
stated.
Before commencing
installation, remove the top
cover of the remote blower
(REMP ONLY). Check to see
if the blower wheel turns
freely. Do not replace the top
cover until the installation is
complete.
Model
No.
Overall Chassis
Width
Overall Chassis
Height
Overall Chassis
Length
Duct Diameter
REMP3
19” (483mm)
5 13/16” (148mm)
25 1/2” (648mm)
8” (203mm)
REMP16
26” (660mm)
9 9/16” (243mm)
33 1/2” (851mm)
10” (254mm)
REMP Overall Dimensions
Model
No.
REMP3
REMP16
Electrical
Supply
Requirements
Maximum
Duct Length
Refer to
Ventilator
Specifications
Max. 60
Equivalent
Straight Feet
Total
Connected
Load
Blower
Rating*
Approx.
Shipping
Weight
0.5kW (4A)
620 CFM
35 lbs.
0.3kW (3A)
980 CFM
55 lbs.
Finish
Galvanized
(may be
painted)
REMP Specifications
"A"
* All the CFM Blower Ratings are valued at 0” (zero-inch) static pressure.
19" (483mm)
17 1/8" (435mm)
9 1/2" (241mm)
7 1/2"
(191mm)
CL
"B"
CL
Power Supply
Conduit
Location
25 1/2"
(648mm)
Attachment
Surface
Electrical
Access Panel
L
BK
M
WIRING DIAGRAM, ILB-8
FAN MOTOR
N
GR
120V, 60Hz, 15A POWER SUPPLY
CAUTION: DISCONNECT POWER SUPPLY AT THE FUSE BOX BEFORE SERVICING THIS EQUIPMENT
Intake Collar
Cutout
Location
Discharge
ILB Overall Dimensions
Front View
26" (660mm)
24" (610mm)
12 11/16" (322mm)
9 1/2"
(241mm)
3 5/8"
(92mm)
CL
CL
Power Supply
Conduit
Location
9 1/4"
(235mm)
CL
24 1/16"
(611mm)
DACOR P/N 85829
2.
Overall Chassis
Height “B”
ILB8
NOTES:
1.
Overall Chassis
Width “A”
33 1/2"
(851mm)
12 1/4"
(311mm)
CL
31 1/2"
(800mm)
Mounting
Flange
3 1/2"
(89mm)
Intake Collar
Cutout
Location
Mounting
Flange
Discharge
REMP3 Overall Dimensions
Top View
7 13/16"
(198mm)
5 13/16"
(148mm)
REMP16 Overall Dimensions
Top View
11 1/2"
(292mm)
9 9/16"
(243mm)
"D"
AIRFLOW
8"
(203mm)
10"
(254mm)
Intake Collar
Intake Collar
ROTATION
Attachment
Surface
"C"
Discharge
Discharge
ILB Overall Dimensions
Side View
REMP3 Overall Dimensions
Side View
REMP16 Overall Dimensions
Side View
2