Download ALLEN & HEATH Xone:3D Service manual

SERVICE MANUAL
Issue 2
Publication AP6389
Allen & Heath
1
XONE:3D Service Manual
Limited One Year Warranty
This product is warranted to be free from defects in materials or
workmanship for period of one year from the date of purchase by the
original owner.
To ensure a high level of performance and reliability for which this
equipment has been designed and manufactured, read this User Guide
before operating. In the event of a failure, notify and return the
defective unit to ALLEN & HEATH Limited or its authorised agent as
soon as possible for repair under warranty subject to the following
conditions
Conditions Of Warranty
The equipment has been installed and operated in accordance with the
instructions in this User Guide.
The equipment has not been subject to misuse either intended or
accidental, neglect, or alteration other than as described in the User
Guide or Service Manual, or approved by ALLEN & HEATH.
Any necessary adjustment, alteration or repair has been carried out by
ALLEN & HEATH or its authorised agent.
This warranty does not cover fader wear and tear.
The defective unit is to be returned carriage prepaid to ALLEN &
HEATH or its authorised agent with proof of purchase.
Units returned should be packed to avoid transit damage.
In certain territories the terms may vary. Check with your ALLEN &
HEATH agent for any additional warranty which may apply.
This product complies with the European Electro magnetic
Compatibility directives 89/336/EEC & 92/31/EEC and the
European Low Voltage Directives 73/23/EEC & 93/68/EEC.
This product has been tested to EN55103 Parts 1 & 2 1996 for use in
Environments E1, E2, E3, and E4 to demonstrate compliance with the
protection requirements in the European EMC directive 89/336/EEC.
During some tests the specified performance figures of the product were
affected. This is considered permissible and the product has been passed as
acceptable for its intended use. Allen & Heath has a strict policy of
ensuring all products are tested to the latest safety and EMC standards.
Customers requiring more information about EMC and safety issues can
contact Allen & Heath.
XONE:3D Service Manual AP6389 Issue 1
Copyright © 2006 Allen & Heath Limited. All rights reserved
Allen & Heath Limited
Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK
http://www.allen-heath.com http://www.xone.co.uk
Allen & Heath
2
XONE:3D Service Manual
Allen & Heath
3
XONE:3D Service Manual
CAUTION
INPUT 4
PHONO L
INPUT 3
R
PHONO L
INPUT 2
R
PHONO L
INPUT 1
R
LINE
A
L
R
FX1
R
LINE
B
L
R
FX2
WARNING: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE FUSE WITH SAME TYPE AND RATING.
ATTENTION: REMPLACER LE FUSIBLE AVEC
UN DES MEMES CARACTERISTIQUES.
LINE
WARNING: THIS APPARATUS MUST BE EARTHED.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE.
R
LINE
L
R
LINE
L
L
GAME/MIDI
R
AC MAINS IN ~
OFF
ON
0
I
L
FX RETURNS
L
R
T500mAL 250V 20mm
MIX OUT
LEFT
MONITOR
RIGHT
FX1 SEND
L
L
SPDIF
SOUNDCARD OUTPUTS
FX2 SEND
L
CH1
L
CH3
L
CH5
L
R
CH2
R
CH4
R
CH6
R
FUSE
IN
FOOT
SWITCH
DIGITAL AUDIO
R
R
IN
OPTICAL
OUT
SERIAL No:
MIDI
IN
USB
OUT
TO PC
OUT
100 - 240V~
47-63Hz ~ 30W MAX
MADE IN THE UK BY ALLEN & HEATH LIMITED
ALLEN&HEATH
BPM
+10!
+6
+3
MODE
MIDI CH
0
MIDI
-3
START
STOP
FX1
RESET
FX1
FX1
-10
00
+6
CLOCK
00
+6
PRE
+
PULL
FX1
-6
00
+6
PRE
00
+6
PRE
-15
PRE
-20
PUSH
L
TAP
FX2
FX2
FX2
R
FX2
5
4
6
3
+6
00
AUTO BPM
SELECT
FX2
MIX
LINE A
LINE B
9
0
5
0
PHONO
LINE
SC 5 - 6
LEVEL
+10
+10
-10
HF
+10
-10
HF
MONITOR
HF
CUE ACTIVE
+6
+6
OFF
MF
+6
OFF
F
G
MF
FX 2
J
K
+6
OFF
LF
1
DEPTH
2
ASSIGN
XFADE
H
L
+6
+6
OFF
OFF
+6
OFF
+6
PHONES
LF
LF
LF
10
+6
OFF
1X
RES
+6
OFF
FILTER
XFADE
1X
Y2
Y2
1X
Y2
1X
ADD MIX
5
6
9
10
1
0
CUE
MILD
HPF
BPF
LPF
LEVEL
Q
R
S
T
U
V
W
X
WILD
HPF
+10!
+10!
+10!
+10!
+6
+6
+6
+6
+3
+3
+3
+3
0
0
0
0
-3
-3
-3
-3
-6
-6
-6
-6
-10
-10
-10
-10
-15
-15
-15
-15
-20
-20
-20
-20
JOG / SELECT
BPF
LPF
FREQ
FREQ
OO
20Hz
P
4
WILD
JOG / SELECT
O
11
RES
3
N
8
2
Y2
M
7
3
OFF
CUE
2
CUE
4
FILTER
XFADE
OFF
CUE
1
MILD
FILTER
XFADE
OFF
CUE
+6
OFF
FILTER
XFADE
OFF
ON
I
FX 1
+6
OFF
MF
MF
OFF
7
8
1+2
E
8
9
10
9
0
D
7
0
+10
6
3
2
1
C
6
3
TAP
TEMPO
B
5
4
LEVEL
FX2
RTN
LFO
A
10
SC 1 - 2
LEVEL
-10
HF
6
10
5
9
0
1
OFF
4
8
1
2
-10
7
8
9
7
2
FX1
RTN
10
3
2
1
+6
00
PHONO
LINE
SC 3 - 4
LEVEL
6
7
8
4
PHONO
LINE
SC 1 - 2
5
3
2
1
+6
00
MIX
OFF
4
+6
00
OO
OO
OO
20Hz
20kHz
XFADE CURVE
X
20kHz
Y
FILTER 1 ON
FILTER 2 ON
LF
-12
PHONES
Allen & Heath
5
HF
+12
-12
LEVEL
+12
0
10
MIC
XONE:3D Service Manual
EARTHING
The connection to earth (ground) in an audio system is important for
two reasons:
SAFETY - To protect the operator from high voltage electric shock,
and
AUDIO PERFORMANCE - To minimise the effect of earth (ground)
loops which result in audible hum and buzz, and to shield the audio
signals from interference.
For safety it is important that all equipment earths are connected to
mains earth so that exposed metal parts are prevented from carrying
high voltage which can injure or even kill the operator. It is
recommended that a qualified system engineer check the continuity of
the safety earth from all points in the system including microphone
bodies, turntable chassis, equipment cases, and so on.
The same earth is also used to shield audio cables from external
interference such as the hum fields associated with power transformers,
lighting dimmer buzz, and computer radiation. Problems arise when the
signal sees more than one path to mains earth. An ‘earth loop’ (ground
loop) results causing current to flow between the different earth paths.
This condition is usually detected as a mains frequency audible hum or
buzz.
To ensure safe and trouble-free operation we recommend the following:
Have your mains system checked by a qualified electrician. If
the supply earthing is solid to start with you are less likely to experience
problems.
Do not remove the earth connection from the console mains
plug. The console chassis is connected to mains earth through the
power cable to ensure your safety. Audio 0V is connected to the
console chassis internally. If problems are encountered with earth loops
operate the audio ‘ground lift’ switches on connected equipment
accordingly, or disconnect the cable screens at one end, usually at the
destination.
Make sure that turntables are correctly earthed. A chassis earth
terminal is provided on the console rear panel to connect to turntable
earth straps.
Use low impedance sources such as microphones and line level
equipment rated at 200 ohms or less to reduce susceptibility to
interference. The console outputs are designed to operate at very low
impedance to minimise interference problems.
Use balanced connections for microphones and mix output as
these provide further immunity by cancelling out interference that may
be picked up on long cable runs. To connect an unbalanced source to a
balanced console input, link the cold input (XLR pin 3 or jack ring) to 0V
earth (XLR pin 1 or jack sleeve) at the console. To connect a balanced
XLR output to unbalanced equipment, link the cold output to 0V earth
at the console.
Use good quality cables and connectors and check for correct
wiring and reliable solder joints. Allow sufficient cable loop to prevent
damage through stretching.
If you are not sure ... Contact your service agent or local Allen &
Heath dealer for advice.
Allen & Heath
7
XONE:3D Service Manual
MIXER TROUBLESHOOTING
If things don’t seem to be working properly the first thing is not to panic. It is very
easy to overlook a simple error or obvious problem in the heat of the moment.
Instead, work methodically through a few checks before deciding there is an actual
problem.
Does the mixer power
up
NO
Check the mains power socket
with another appliance. If this
works try another IEC lead on
the mixer.
If it still doesn’t work then
check the fuse on the back of
the unit. If it is blown only
replace it with an identical type:
T500mA
If the Fuse blows again, or the
unit is still dead, contact your
service agent
YES
Are the CUE and Filter switches working?
NO
YES
Front panel control
processor
not
working.
Reboot the mixer and
if still does not work
contact your service
agent
NO
Check the channel input
selection is correct for
each audio source, that the
player is working and that
the interconnected leads
are plugged into the
correct channel input.
NO
BPM processor not working.
Try rebooting the mixer and
if it still does not work contact your service agent
Is there audio on the
channels as shown by
the meters?
YES/NO
With the channel fader raised
is there a signal on the main
left/right monitor meters?
See Following pages for more
information on interfacing the
Xone:3D to a computer
YES
Check FX1/2 monitor switches are up, that no channel cues
are selected and that the crossfader is off
Allen & Heath
YES
Does the Xone:3D Utility
register that the unit is
connected? See page 11
YES
NO
Is the BPM display
working? Press Tap
Tempo to confirm
8
Check that the Mix and monitor level controls are
raised, that any connected amps are switched on
with their level controls raised, the interconnects
between the mixer and the amps and between the
amps and the speaker system
XONE:3D Service Manual
Allen & Heath
9
XONE:3D Service Manual
Allen & Heath
10
XONE:3D Service Manual
PACKED ITEMS
AP6388 USER GUIDE XONE:3D
Mains Lead
AH0205
AH0323
*MAINS LEAD IEC-2PIN EURO
*MAINS LEAD IEC-3PIN C33 USA
AH0206
*MAINS LEAD IEC-3PIN UK 10AMP
AH6443 Type A-B USB
Lead
AP6442 Xone:3D Utility CD including:
ASIO drivers, Configuration Utility software,
Ableton Live Lite 6 application.
Software Overlay Sheets
For Serial numbers starting X3D:
003-536 Replacement KitAN6441 Ableton Live
AN6442 Native Instruments Tractor
AA6553-L & AA6553-R
Rack Ears.
AB5680 M4x10mm screws
For Serial numbers starting X23D:
003-704 Replacement KitAN6880 Ableton Live
AN6881 Native Instruments Tractor
AL6531 Optical in/out blank plugs
Allen & Heath
4
XONE:3D Service Manual
SCREW TORX-Pt No.AB3820
BPM
SCREW POZI-Pt No. AB3819
7 SEG DISPLAY-Pt No.003-524
MIDI CH
MODE
MIDI
KNOB-Pt No. AJ6379
ENCODER-Pt No. AL6338
BUTTON-Pt No. AJ5325
LIGHT RING Pt No AJ5324
SWITCH-Pt No. AL0374
KNOB-Pt No. AJ5386
POT-Pt No. AI8004
START
STOP
RESET
SWITCH-PtNo. AL6482
CLOCK
+
PULL
PUSH
TAP
AUTO BPM
SELECT
FX2
MIX
SWITCH-PtNo. AL5328
OFF
4
6
3
2
1
KNOB-Pt No.AJ5386
POT-Pt No.AI8007
KNOB-Pt No. AJ4310
FADER-PT No. AI4999
SCREW-Pt No.AB3818
FADER ASSY Pt No. 003-532
5
0
4
5
0
C
TAP
TEMPO
4
D
E
F
G
H
5
I
J
K
L
10
DEPTH
2
ASSIGN
XFADE
SWITCH-Pt No. AL5328
1X
ON
RES
KNOB-Pt No. AJ5387
POT Pt No. AI8007
KNOB-Pt No. AJ6379
ENCODER-Pt No. AL6338
JOG / SELECT
1+2
KNOB-Pt No.AJ5386
POT-Pt No. AI8007
KNOB-Pt No. AJ5386
POT-Pt No. AI8003
6
7
8
9
1
CAP-Pt No. AJ4251
SWITCH-Pt No. AL0374
FX2
RTN
LFO
0
B
7
8
9
10
3
2
1
A
FX1
RTN
6
3
2
1
BUTTON-Pt No. AJ5325
LIGHT RING Pt No AJ5324
SWITCH-Pt No. AL0374
7
8
9
10
MILD
CUE
CAP--Pt No. AJ3863
SWITCH-Pt No.AL0162
WILD
HPF
BUTTON-Pt No. AJ5325
LIGHT RING Pt No AJ5324
SWITCH-Pt No. AL0374
DECK ASSY-Pt No.AJ6342
+10!
+6
+3
BPF
0
-3
-6
-10
LPF
-15
-20
FREQ
SCREW TORX-Pt No.AB3820
BUTTON-Pt No. AJ5325
LIGHT RING Pt No AJ5324
SWITCH-Pt No. AL0374
20Hz
20kHz
KNOB-Pt No.AJ5387
POT Pt No. AI8004
NUT-Pt No. AB8172
XFADE CURVE
FILTER 1 ON
KNOB-Pt No. AJ5386
POT-Pt No. AI8004
ALLEN&HEATH
+10!
+6
CAP-Pt No. AJ5388
SWITCH-Pt No. AL0162
FX1
FX1
FX1
+3
0
-3
-6
FX1
-10
+6
00
+6
00
PRE
+6
00
PRE
FX2
+6
00
PRE
FX2
KNOB-Pt No. AJ5386
POT-Pt No. AI8004
PRE
FX2
-15
-20
L
R
FX2
5
4
6
3
00
+6
00
+6
LINE A
LINE B
00
+6
PHONO
LINE
SC 1 - 2
+6
PHONO
LINE
SC 3 - 4
LEVEL
00
CAP-Pt No. AJ4251
SWITCH-Pt No. AL0333
PHONO
LINE
SC 5 - 6
SC 1 - 2
LEVEL
LEVEL
7
2
KNOB-Pt No.AJ5386
POT-Pt No. AI8007
LEVEL
PHONO
LINE
8
1
9
0
10
MIX
SC 1 - 2
5
4
6
3
7
2
-10
+10
-10
HF
+10
-10
HF
+6
OFF
+6
+6
LF
+6
+6
+6
LF
+6
OFF
OFF
+6
OFF
+6
PHONES
CUE ACTIVE
CAP-Pt No. AJ4251
SWITCH-Pt No. AL0162
KNOB-Pt No. AJ5387
POT-Pt No. AI8006
+6
FX 1
FX 2
PHONES
LF
OFF
KNOB-Pt No. AJ5386
POT-Pt No. AI8003
CUE
ADD MIX
5
4
FILTER
XFADE
1X
FILTER
XFADE
1X
Y2
OFF
FILTER
XFADE
Y2
1X
OFF
CUE
FILTER
XFADE
Y2
OFF
CUE
4
+10!
+10!
+10!
+6
+6
+6
+6
+3
+3
+3
+3
0
0
0
0
-3
-3
-3
-3
-6
-6
-6
-6
-10
-10
-10
-10
-15
-15
-15
-15
-20
-20
-20
-20
OO
RES
3
+10!
OO
OO
SWITCH-Pt No. AL5328
Y2
CUE
2
6
7
3
8
2
KNOB-Pt No. AJ5386
POT-Pt No. AI8007
OFF
CUE
1
1X
10
MONITOR
+6
OFF
8
9
0
MF
OFF
LF
OFF
+6
MF
OFF
KNOB-Pt No. AJ5386
POT-Pt No. AI8006
+10
HF
OFF
MF
OFF
-10
HF
OFF
MF
+10
1
BUTTON-Pt No. AJ5325
LIGHT RING Pt No AJ5324
SWITCH-Pt No. AL0374
KNOB-Pt No. AJ5387
POT-Pt No. AI8007
SCREW POZI-Pt No. AB3819
KNOB-Pt No.AJ5320
FADER ASSY-Pt No.003-526
FADER-Pt No. AI6343
9
10
1
0
RES
MILD
BPF
BUTTON-Pt No. AJ5325
LIGHT RING Pt No AJ5324
SWITCH-Pt No. AL0374
LPF
FREQ
KNOB-Pt No. AJ5387
POT-Pt No. AI8004
OO
XFADE CURVE
Allen & Heath
Y
WILD
HPF
20Hz
X
LEVEL
11
SCREW POZI-Pt No. AB3819
KNOB-Pt No. AJ5320
FILTER 2 ON FADER ASSY-Pt No.003-579
1
BUTTON-Pt No. AJ5325
LIGHT RING Pt No AJ5324
SWITCH-Pt No. AL0374
20kHz
FILTER 2 ON
XONE:3D Service Manual
TERMINAL POST-PT No
AL8106
RCA PHONO PLUG SHORTINGPt No. AL4396
D TYPE CONNECTORPt No. AL6351
QUAD RCA SOCET-Pt No. AL497
SCREW-Pt No. AB2771
CAUTION
INPUT 4
PHONO L
R
INPUT 3
PHONO L
INPUT 2
R
PHONO L
LINE
0
I
OFF
ON
L
R
LINE
L
R
LINE
L
INPUT 1
R
LINE
A
L
R
FX1
R
LINE
B
L
R
FX2
WARNING: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE FUSE WITH SAME TYPE AND RATING.
ATTENTION: REMPLACER LE FUSIBLE AVEC
UN DES MEMES CARACTERISTIQUES.
WARNING: THIS APPARATUS MUST BE EARTHED.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE.
JACK SOCKETPt No. AL0328
FX RETURNS
L
R
L
GAME/MIDI
R
AC MAINS IN ~
T500mAL 250V 20mm
LEFT
MIX OUT
RIGHT
MONITOR
L
FX1 SEND
L
SPDIF
SOUNDCARD OUTPUTS
FX2 SEND
L
CH1
L
CH3
L
CH5
L
R
CH2
R
CH4
R
CH6
R
FUSE
IN
FOOT
SWITCH
DIGITAL AUDIO
OPTICAL
OUT
R
R
SERIAL No:
IN
MIDI
IN
OUT
USB
TO PC
OUT
100 - 240V~
47-63Hz ~ 30W MAX
MADE IN THE UK BY ALLEN & HEATH LIMITED
SWITCH CAP-Pt
No AJ2887
PHONO DUAL
SOCKET-Pt No.
AL0566
XLR MALE SKT-Pt No. AL2411
SCREW-Pt No. AB2810
RCA DUAL VERTICAL SOCKETPt No.AL3753
SCREW -Pt No.AB2771
FUSE 20mm 500 mAPt No. AL3534
5 WAY DINPt No. AL0095
OPTICAL IN SOCKETUSB SOCKETPt No. AE6096
Pt No. AL6096
OPTICAL OUT SOCKETPt No. AE5899
OPTICAL IN/OUT BLANKING PLUGPt No. AL6531
LF
-12
HF
+12
-12
PHONES
JACK SOCKETPt No. AL5323
AL5904AL5904AL5904AL5904AL5904AL4606AL6407AL6592AL5485AL6098AL3817AL3817AH2228
0
10
KNOB-Pt No.
AJ4346
POT-Pt No.
AI8004
KNOB-Pt No.
AJ4346
POT-Pt No.
AI8003
XLR SOCKETPt No. AL2414
SCREW-Pt No.
CONNECTING WIREFORMS USED IN CONSOLE
to
HEADPHONE ASSY
7 SEGMENT DISPLAY
ANALOGUE SLAVE ASSY
JOGWHEEL (L) ASSY
JOGWHEEL (R) ASSY
CONNECTOR ASSY
MIDI SLAVE (L) ASSY
MIDI CONTROL (R) ASSY
ANALOGUE SLAVE ASSY
GAMEPORT ASSY
LINEAR FADER ASSY`S
X FADER ASSY
MIDI FADER ASSY`S
Allen & Heath
+12
MIC
JACK SOCKETPt No. AL0328
From
LEVEL
MASTER ASSY
USB CONTROL ASSY
POWER SUPPLY ASSY
MIDI SLAVE (L) ASSY
MIDI SLAVE (R) ASSY
MASTER ASSY
USB CONTROL ASSY
USB CONTROL ASSY
USB CONTROL
USB COTROL ASSY
INPUT ASSY`S
FILTER ASSY
MIDI SLAVE ASSY`S
2
XONE:3D Service Manual
MASTER ASSYPt No. 003-522
Control IP (MIDI
controller strips)
IP 1, 2, 3, & 5, 6, 7
X:3D 003-535
X2:3D 003636
INPUT ASSYPt No. 003521
FILTER ASSY–
Pt No. 003-525
7 SEGMENT DISPLAY ASSYPt No. 003-695
Control IP (MIDI
controller strips)
IP 1, 2, 3, & 5, 6, 7
X:3D 003-535
X2:3D 003636
IP 4 & 8 both models
003-635 INPUT P ASSY CONTROL
Pt No. 003-635
CONTROL
INPUT
P ASSY IP 4 & 8 both
models
Pt
No. 003-635
003-635
MIDI SLAVE R ASSYPt No. 003-546
MIDI SLAVE L ASSYPt No. 003-523
MIDI FADER ASSYPt No. 003-532
(under midi slave assy)
MIDI FADER ASSYPt No. 003-532
(under midi slave assy)
ANALOGUE SLAVE ASSY_
Pt No. 003-519
JOGWHEEL ASSYPt No. 003-533
JOGWHEEL ASSYPt No. 003-533
CONTROL INPUT ASSY_
Pt No.. 003-636
LINEAR FADER ASSYPt No. 003-526
X FADER ASSYPt No. 003-579
CONTROL INPUT ASSY_
Pt No.. 003-636
GAMEPORT ASSYPt No. 003-531
CONNECTOR ASSYPt No. 003-527
POWER SUPPLY ASSYPt No. 003-233
USB CONTROL ASSYPt No. 003-528
HEADPHONE SOCKET ASSYPt No. 003-530
Allen & Heath
3
XONE:3D Service Manual