Download Samsung SAMTRON 78BDF Service manual
Transcript
COLOR MONITOR PN17KT/KO PN17JT/JO SERVICE Manual COLOR MONITOR CONTENTS 1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Alignment & Adjustments 5. Troubleshooting 6. Exploded View & Parts List PN17KT/JT 7. Electrical Parts List 8. Block Diagram 9. Wiring Diagram 10. Schematic Diagrams PN17KO/JO Samsung Electronics Co.,Ltd. 416, Maetan-3Dong, Paldal-Gu, Suwon City, Kyungki-Do, Korea. Tel : +82-31-200-7920 Fax : +82-31-200-7802 Printed in Korea P/N : BH68-00393J-00 http://www.samsungmonitor.com (SyncMaster Worldwide) http://www.samsung-monitor.com (SyncMaster USA) http://www.samtron.com (SAMTRON Worldwide) http://www.sec.co.kr/monitor (Korea) 1 Precautions 1-1 Safety Precautions WARNINGS 1. For continued safety, do not attempt to modify the circuit board. 2. Disconnect the AC power before servicing. 3. When the chassis is operating, semiconductor heatsinks are potential shock hazards. 1-1-1 1. When servicing the high voltage system, remove the static charge by connecting a 10 kohm resistor in series with an insulated wire (such as a test probe) between the chassis and the anode lead. 2. When troubleshooting a monitor with excessively HV, avoid being unnecessarily close to the monitor. Do not operate the monitor for longer than is necessary to locate the cause of excessive voltage. 3. High voltage should always be kept at the rated value, no higher. Only when high voltage is excessive are X-rays capable of penetrating the shell of the CRT, including the lead in glass material. Operation at high voltages may also cause failure of the CRT or high voltage circuitry. 5. When the HV regulator is operating properly, there is no possibility of an X-ray problem. Make sure the HV does not exceed its specified value and that it is regulating correctly. The CRT is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the CRT only with one that is the same or equivalent type as the original. 6. Handle the CRT only when wearing shatterproof goggles and after completely discharging the high voltage anode. 7. Do not lift the CRT by the neck. 1-1-2 Leakage Current Hot Check (Figure 1-1): WARNING: Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 4. With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit’s AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test. Servicing the High Voltage and CRT : WARNING:A high voltage adjusted to the wrong value may cause excessive X-ray emissions. 4. 3. Fire and Shock Hazard : Before returning the monitor to the user, perform the following safety checks: 1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor. 2. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc. PN17K*/PN17J* (READING SHOULD NOT BE ABOVE 0.5mA) LEAKAGE CURRENT TESTER DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED) EARTH GROUND Figure 1-1. Leakage Current Test Circuit 1-1-3 Product Safety Notices Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by ! on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. Components identified by on schematics and parts lists must be sealed by a soldering iron after replacement and adjustment. 1-1 1 Precautions 1-2 Servicing Precautions WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances create conflict between the servicing precautions and safety precautions, always follow the safety precautions. WARNING2: A high voltage adjusted to the wrong value may cause excessive X-ray emissions. WARNING3: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet, and should be followed closely. 2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect all test components in parallel with an electrolytic capacitor. 3. 4. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the +B voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last. 1-3 Electrostatically Sensitive Devices (ESD) Precautions Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some fieldeffect transistors. The following techniques will reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor. 6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 7. 2. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 3. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs. Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions. 4. Use only a grounded-tip soldering iron to solder or desolder ESDs. 5. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ESDs. 1-2 8. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD. 9. Indicates ESDs on the Schematic Diagram in this manual. PN17K*/PN17J* 2 Product Specifications 2-1 Specifications Description Item PN17K* PN17J* Picture Tube: 17-Inch (43 cm): 16-inch (40.6 cm) viewable, Perfect Flatness, 90˚ Deflection, Semi- tint, Invar shadow mask, Anti-static silica coating, 0.26 mm Dot pitch Scanning Frequency Horizontal Vertical 30 kHz ~ 70 kHz (Automatic) 50 Hz ~ 160 Hz (Automatic) Display Colors Unlimited colors Maximum Resolution Horizontal Vertical 1280 Dots 1024 Lines Input Video Signal Analog, 0.7 Vp-p positive at 75 Ω, internally terminated Input Sync Signal Separate Sync : TTL level positive/negative Maximum Pixel Clock rate 110 MHz Active Display (Horizontal/Vertical) 312 mm ± 4 mm / 234 mm ± 4 mm Input Voltage AC 90 ~ 264 Volts, 60 Hz / 50 Hz ± 3 Hz Power Consumption 90 Watt (max) Dimensions (W x D x H) (with Base) 15.67 x 16.22 x 15.75 Inches (398 x 412 x 400 mm) Weight 41.22 lbs (18.7 kg) Environmental Considerations Operating Temperature : 32°F ~ 104°F (0°C ~ 40°C) Humidity : 10 % ~ 80 % Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 % 30 kHz ~ 85 kHz (Automatic) 50 Hz ~ 160 Hz (Automatic) 1600 Dots 1200 Dots 135 MHz 100 Watt (max) • Above models comply with SWEDAC MPR II / TCO99 recommendations for reduced electromagnetic fields. • Designs and specifications are subject to change without prior notice. PN17K*/PN17J* 2-1 2 Product Specifications 2-2 Pin Assignments Sync Type Separate Macintosh Pin No. 1 Red GND-R 2 Green Red 3 Blue H/V Sync. 4 N-C Sense 0 5 GND (DDC) Green 6 GND-R GND-G 7 GND-G Sense 1 8 GND-B Reserved 9 N-C Blue 10 GND-Sync./Self-raster Sense 2 11 N-C GND 12 DDC Data V-Sync. 13 H-Sync. GND-B 14 V-Sync. GND 15 DDC Clock H-Sync. 1 6 2 7 5 3 10 8 12 13 14 15 Figure 2-1. Male Type 2-2 Figure 2-2. Male Type PN17K*/PN17J* 2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1. Timing Chart Mode IBM VESA 640/75 Hz VGA2/70 Hz VGA3/60 Hz 640 x 480 720 x 400 640 x 480 Timing (PN17K*) 640/85 Hz 640 x 480 800/75 Hz 800/85 Hz 1024/75 Hz 1024/85 Hz 1280/75 Hz 1280 x 1024 800 x 600 800 x 600 1024 x 768 1024 x 768 (PN17J*) fH (kHz) 31.469 31.469 37.500 43.269 46.875 53.674 60.023 68.677 79.976 A µsec 31.777 31.778 26.667 23.111 21.333 18.631 16.660 14.561 12.504 B µsec 3.813 3.813 2.032 1.556 1.616 1.138 1.219 1.016 1.067 C µsec 1.907 1.907 3.810 2.222 3.232 2.702 2.235 2.201 1.837 D µsec 25.422 25.422 20.317 17.778 16.162 14.222 13.003 10.836 9.481 E µsec 0.636 0.636 0.508 1.556 0.323 0.569 0.203 0.508 0.119 fV (Hz) 70.087 59.940 75.000 85.008 75.000 85.061 75.029 84.997 75.025 O msec 14.268 16.683 13.333 11.764 13.333 11.756 13.328 11.765 13.329 P msec 0.064 0.064 0.080 0.671 0.064 0.056 0.050 0.044 0.038 Q msec 1.080 1.048 0.427 0.578 0.448 0.503 0.466 0.524 0.475 R msec 12.711 15.253 12.800 11.093 12.800 11.179 12.795 11.183 12.804 S msec 0.413 0.318 0.027 0.023 0.021 0.019 0.017 0.015 0.013 28.322 25.175 31.500 36.000 49.500 56.250 78.750 94.500 135.000 Polarity H.Sync Negative Negative Negative Negative Positive Positive Positive Positive Positive V.Sync Positive Negative Negative Negative Positive Positive Positive Positive Positive Remark Separate Separate Separate Separate Separate Separate Separate Separate Separate Clock Frequency (MHz) Separate Sync Horizontal Vertical Video Video Video Video CC DD E E Q RR Q S S Sync Sync Sync Sync BB PP AA O O A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width C : Back porch D : Active time Q : Back porch R : Active time E : Front porch PN17K*/PN17J* S : Front porch 2-3 2 Product Specifications Memo 2-4 PN17K*/PN17J* 3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the PN17K*/PN17J* monitors. WARNING: This monitor contains electrostatically sensitive devices. Use with caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly. 2. To remove the Rear Cover, you must use the special opening jig tool. 3-1-1 Before making Disassembly 1. Disconnect the power cord from the monitor. 2. With a pad beneath it, stand the monitor on its front with the screen facing downward and the base close to you. 4. Push the Opening jig each groove along the top of the monitor till it makes a “ttak” sound. (2 grooves : Left and Right, Make sure each snap is disengaged.) 3-1-2 Cabinet Disassembly 1. Remove the Stand from the monitor. (Refer to Stand manual) 2. Remove 2 screws on the Rear cover. Figure 3 5. Pull the Rear Cover up off the monitor. Figure 1 3. Incline the monitor by lifting the rear of the monitor. Figure 4 6. Remove the Shield.(TCO 99) Figure 2 Figure 5 PN17K*/PN17J* 3-1 3 Disassembly and Reassembly 7. Using pinch-nose pliers or ling-nose pliers, acrefully disconnect the Anode Cap from the CRT. Warning: Do not touch the Anode contact on the CRT (High Voltage may remain). 3-1-3 Removing the CRT Socket PCB 1. Complete all previous steps. 2. Lift up the Video Spring and remove the CRT Socket PCB from the CRT. Figure 7 6. Disconnect the Tilt connector at the CN2(CN22) connector on the Main PCB. 7. Disconnect the Sub PCB connector at the CN201 connector on the Main PCB. 8. Remove the screws on the back and along each side of the Bottom Chassis. 9. Carefully lift the Main PCB Ass’y and remove the remaining ground wires. 10. Place the Main PCB Ass’y on a flat, level surface that is protected from static electricity. Figure 6 3. Disconnect all connectors on the CRT Socket PCB. 4. Using a solder iron, disconnect Ground (GND) on the back of the Video Shield and remove the Shield Cap. 5. Remove the screw on the front of the Shield Socket. 6. Desolder the 4 tabs on the CRT Socket PCB and remove Shield. 7. Place the Video PCB on a flat, level surface that is protected from static electricity. 3-1-4 Removing the Main PCB 3-1-5 CRT Ass’y Disassembly 1. Complete all previous steps. 2. Straighten the Degaussing Coil Assembly coated metal ties and lift the Coil Ass’y from the CRT. 3. Remove the four corner screws and lift the CRT up and away from the Front Cover Assembly and place it on a padded surface. Caution: Do not lift the CRT by the neck. If you will be returning this CRT to the monitor, be sure to place the CRT face downward on a protective pad. 1. Complete all previous steps. 2. Disconnect the Degaussing Coil at GT601 and CN603 on the Main PCB. 3. Disconnect all easily accessible ground wires on the PCB and Bottom Chassis. 4. Disconnect the DY connector at the CN401 connector on the Main . 5. Using the jig, release the snaps (2) connecting the Front Cover and the PCB then lift up the Bottom to separate the two Shield. 3-2 Reassembly Reassembly procedures are in the reverse order of Disassembly procedures. 3-2 PN17K*/PN17J* 4 Alignment and Adjustments This section of the service manual explains how to make permanent adjustments to the monitor. Directions are given for adjustments using the monitor Interface Board Ver. 2.0 and software (Softjig). 4-1 Adjustment Conditions Caution:Changes made without the Softjig are saved only to the user mode settings. As such, the settings are not permanently stored and may be inadvertently deleted by the user. 4-1-1 Before Making Adjustments 4-1-2 Required Equipment 4-1-1 (a) ORIENTATION When servicing, always face the monitor to the east. The following equipment may be necessary for adjustment procedures: 4-1-1 (b) MAGNETIC FIELDS Whenever possible, use magnetic field isolation equipment such as a Helmholtz field to surround the monitor. If a Helmholtz field is not available, frequently degauss the unit under test. Caution: Other electrical equipment may cause external magnetic fields which may interfere with monitor performance. Use an external degaussing coil to limit magnetic build up on the monitor. If an external degaussing coil is not available, use the internal degaussing circuit. However, do not use the internal degaussing circuit more than once per 30 minutes. 4-1-1 (c) WARM-UP TIME The monitor must be on for 30 minutes before starting alignment. Warm-up time is especially critical in color temperature and white balance adjustments. 4-1-1 (d) SIGNAL Analog, 0.7 Vp-p positive at 75 ohm, internal termination Sync: TTL level, negative/positive 4-1-1 (e) SCANNING FREQUENCY 4-1-2 (a) DISPLAY CONTROL ADJUSTMENT 1. Non-metallic (–) screwdriver: 1.5, 2.5, 3 mm 2. Non-metallic (+) screwdriver: 1.5, 2.5, 3 mm 3. Digital Multimeter (DMM), or Digital Voltmeter 4. Signal generator, or DM200 software 5. Software: Softjig or DM200 6. Interface Board Ver. 2.0 Code No. BH81-90001K 7. Parallel communications cable (25-pin to 25-pin); Code No. BH81-90001H 8. Signal cable (15-pin to 15-pin cable with additional 3-pin connector); Code No. BH81-90001J 9. 5 V DC adapter, not supplied 10. Personal computer Note: Softjig Ass’y (includes items 6, 7 and 9) Code No. BH81-90001L 4-1-2 (b) COLOR ADJUSTMENTS 1. All equipment listed in 4-1-2 (a), above 2. Color analyzer, or any luminance measurement equipment Horizontal: PN17K* : 30 kHz ~ 70 kHz (Automatic) PN17J* : 30 kHz ~ 85 kHz (Automatic) Vertical: 50 Hz ~ 160 Hz (Automatic) Unless otherwise specified, adjust at the 1024 x 768 mode (68 kHz/85 Hz) signal. PN17K*/PN17J* 4-1 4 Alignment and Adjustments 4-1-3 Connecting the SoftJig Connect the monitor to the signal generator and/ or PC as illustrated in Figures 4-1 and 4-2. Note: The signal cable connector which includes the 3-wire cable must connect to the monitor. If you use Setup 2 (PC only, no signal generator) you can only make adjustments to the signal timing available on that computer system. To make corrections to all factory timings requires the use of an additional signal generator. MONITOR INTERFACE BOARD VER. 2.0 5V DC ADAPTOR SIGNAL CABLE 3-WIRE CABLE PARALLEL CABLE SIGNAL GENERATOR PC Figure 4-1. Setup 1, With Signal Generator MONITOR INTERFACE BOARD VER. 2.0 3-WIRE CABLE 5V DC ADAPTOR SIGNAL CABLE PARALLEL CABLE PC D-SUB CONNECTOR Figure 4-2. Setup 2, Without Signal Generator 4-2 PN17K*/PN17J* 4 Alignment and Adjustments 4-2 Display Control Adjustments 4-2-1 HIGH VOLTAGE ADJUSTMENT Signal: Display image: Contrast: Brightness: Limit: 1024 x 768 (68 kHz/85 Hz) Don’t care Manimum Manimum 26.0 kV ± 0.5 kV Measure the hight voltage level at the anode cap. High voltage should be within the limit as above. If the high voltage needs adjustment use the following procedure. PROCEDURE 1. Turn the power off and disconnect the AC line cord from the power source. 2. Turn the power on after connecting high voltage Probe. 3. Using the jig, adjust the high voltage to the specification. * High Voltage Adjustment PROCEDURE using Softjig ① Select matching model name in “Model” field. ➁ Select “ @7: Zero Beam” in menu after selecting “Extra 1” ➂ Adjust high voltage using control bar after selecting “HV VOL” ➃ Turn the power off/on after adjustment finished. ➄ Check the high voltage has been fixed with adjusted value after reselecting “@7: Zero Beam”. 4-2-2 SCREEN VOLTAGE CHECK CONDITIONS Signal: 1024 x 768 (68 kHz/85 Hz) Display image: Contrast: Brightness: Limit: Don’t care Manimum Manimum 520 V ± 10 V Measure the Screen voltage (G2 voltage) at the pin (CN501) on the Main PCB. PROCEDURE 1. Connect the high voltage probe to the CN501. (Main PCB) 2. Using the jig, adjust the G2 voltage to the specification. * G2 Voltage (Screen voltage) Adjustment PROCEDURE using Softjig ① Select matching model name in “Model” field. ➁ Select “ @7: Zero Beam” in menu after selecting “Extra 1” ➂ Adjust G2 using control bar after selecting “G2 CONT” PN17K*/PN17J* 4-2-3 CENTER RASTER Adjust SW401 so that the back raster comes to the center when you apply each basic mode. 4-2-4 Centering Centering means to position the center point of the display in the middle of the display area. Horizontal size and position and vertical size and position control the centering of the display. Adjust the horizontal size and vertical size to their optimal settings: 312 mm (H) x 234 mm. Adjust the horizontal position and vertical position to ≤ 4.0 mm of the center point of the screen. |A-B| ≤ 4.0 mm |C-D| ≤ 4.0 mm C DISPLAY AREA A B EDGE OF BEZEL D Figure 4-3. Centering 4-2-4 (a) HORIZONTAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum Use control bar after selecting “SIZE B+” in left menu to adjust the horizontal size of the display pattern to 312 mm with OSD “H-SIZE” fixed “39”. (Tolerance: ± 4 mm.) Specially run “All mode save” after horizontal size adjustment in order to save “SIZE B+” values of other modes automatically. 4-2-4 (b) VERTICAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum Use control bar after selecting “V-SIZE” in left menu to adjust the vertical size of the display pattern to 234 mm. (Tolerance: ± 3 mm.) 4-3 4 Alignment and Adjustments 4-2-4 (c) HORIZONTAL POSITION ADJUSTMENT CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz Crosshatch pattern Use control bar after selecting “H-POSITION” in left menu to center the horizontal image on the raster. 4-2-4 (d) VERTICAL POSITION ADJUSTMENT CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz Crosshatch pattern Use control bar after selecting “V-POSITION” in left menu to center the vertical image on the raster. 4-2-5 Linearity Linearity affects the symmetry of images as they appear on the screen. Unless each row or column of blocks in a crosshatch pattern is of equal size, or within the tolerances shown in Table 4-2 , an image appears distorted, elongated or squashed. Horizontal Linearity = 2x 4-2-5 (a) HORIZONTAL LINEARITY ADJUSTMENT CONDITIONS Scanning frequency: 68 kHz/85 Hz Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum To adjust the Horizontal Linearity, refer to Table 4-1 for the tolerance range. Increase or decrease H_LIN to optimize the image. 4-2-5 (b) VERTICAL LINEARITY ADJUSTMENT CONDITIONS Scanning frequency: 68 kHz/85 Hz Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum To adjust the Vertical Linearity, refer to Table 4-1 for the tolerance range. Use control bar after selecting “V-LINEARITY BAL” in left menu to optimize the image. X max-X min x100 X max+X min Y max-Y min Vertical Linearity = 2x x100 Y max+Y min Table 4-1 Adjacent Linearity Entire Linearity Preset mode ≤ 4% ≤ 8% Pre-load mode (48kHz~) ≤ 5% ≤ 10% Pre-load mode (under 48kHz) ≤ 5% ≤ 14% ❈ Preset Mode : 68KHz / 85Hz Pre-load Mode : Refer to Timing Chart 4-4 PN17K*/PN17J* 4 Alignment and Adjustments 4-2-6 Trapezoid Adjustment 4-2-9 Side Pincushion Adjustment CONDITIONS Scanning frequency: Display image: Brightness: Contrast: CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum Use control bar after selecting “TRAPEZOID” in left menu to make the image area rectangular. Use control bar after selecting “PINCUSHION” in left menu to straighten the sides of the image area. | C1 |, | C2 | ≤ 2.0 mm, | D1 |, | D2 | ≤ 2.0 mm. | A - B | < 4 mm A 68 kHz/85 Hz Crosshatch pattern C2 A D1 B D2 B Figure 4-4. Trapezoid C1 4-2-7 Pinbalance Adjustment CONDITIONS Scanning frequency: Display image: Brightness: Contrast: Figure 4-7. Pincushion 4-2-10 Tilt Adjustment 68 kHz/85 Hz Crosshatch pattern Maximum Maximum CONDITIONS Scanning Frequency: Display image: Brightness: Contrast: | D1 |, | D2 | ≤ 2.0 mm D1 D2 D1 Figure 4-5. Pinbalance 68 kHz/85 Hz Crosshatch pattern Maximum Maximum Use control bar after selecting “ROTATION” in left menu to correct the tilt of the display. 4-2-11 Degauss Use control bar after selecting “PINBALANCE” in left menu to optimize the image. No adjustments are available for the degaussing circuit. The degaussing circuit can effectively function only once per 30 minutes. 4-2-8 Parallelogram Adjustment 4-2-12 To Delete the User Mode Data CONDITIONS Scanning Frequency: Display image: Brightness: Contrast: To delete the adjustment data from the user modes, click “@4: USER DELETE” in right ment. 68 kHz/85 Hz Crosshatch pattern Maximum Maximum Use control bar after selecting “PARALLEL” in left menu to make the image area rectangular. 4-2-13 Save the Data To save the adjustment data for a mode, press “@3: ALL MODE SAVE” in right ment. 4 mm Figure 4-6. Parallelogram PN17K*/PN17J* 4-5 4 Alignment and Adjustments 4-3 Color Adjustments CAUTION: Check below condition before color adjustment Video signal : Analog 0.7 Vp-p (at 75 ) Sync : TTL level (H, V seperate signal) 4-3-2 (b) R.G.B - GAIN ADJUSTMENT 1/3H-1/2H FRONT BEZEL OPENING * Select “Color” in Softjig menu for color adjustment. BACK RASTER 1/3V-1/2V 4-3-1 Color Coordinates (Temperature) WHITE WINDOW Color temperature is a measurement of the radiant energy transmitted by a color. For computer monitors, the color temperature refers to the radiant energy transmitted by white. Color coordinates are the X and Y coordinates on the chromaticity diagram of wavelengths for the visible spectrum. CONDITIONS Scanning frequency: Display image: Brightness: CONDITIONS Measurement instrument: Color analyzer Scanning frequency: 68 kHz/85 Hz Display image: White flat field at center of display area Luminance: Maximum 4-3-2 (c) WHITE BALANCE ADJUSTMENT PROCEDURE Use the directions in sections 4-3-2 through 4-3-3 to adjust the color coordinates for: 9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02 6500K to x = 0.313 ± 0.02, y = 0.329 ± 0.02 4-3-2 Color Adjustments for 9300K Figure 4-8. White Box Pattern 68 kHz/85 Hz White box pattern 0.06ft-L at Back Raster Pattern Display Contrast: Maximum 1. Click on the << or >> box next to R,G,B _GAIN to adjust the brightness of the Green Gain to 40 ± 1 ft-L. 9300K to x = 0.283 ± 0.02 y = 0.298 ± 0.02 CONDITIONS Scanning frequency: Display image: Brightness: Contrast: Figure 4-9. Full White Pattern 4-3-2 (a) BACK RASTER COLOR ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: FRONT BEZEL OPENING BACK RASTER 68 kHz/85 Hz Back raster pattern Maximum Maximum 1. Select “@1: CHANNEL 1” in right menu to control the color for 9300K. 2. Adjust the luminance of the back raster to between 0.5 to 0.7 ft-L using contron bar after selecting “GREEN CUTOFF” in the menu. 3. Use control bar after selecting “BLUE CUTOFF” in left menu to set the “y” coordinate to 0.298 ± 0.02 4. Use control bar after selecting “RED CUTOFF” in left menu to 0.283 ± 0.02 * If color values would not be matched desirable values, repeat sequence 3 and 4 after readjusting “GREEN CUTOFF” control a little different. 4-6 68 kHz/85 Hz White Box Pattern 0.06ft-L at Back Raster Pattern Display Maximum WHITE WINDOW 1. Click on the << or >> boxes next to R_GAIN and B_GAIN to make the video white. (For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02.) Note: Do not touch the G_GAIN controls. 2. Check the ABL. If it is not within the specifications (30 ± 1 ft-L), use the ABL controls to adjust it. 3. Select COLOR FACTORY SAVE to save the data. 4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION CONDITIONS Scanning frequency: 68 kHz/85 Hz PN17K*/PN17J* 4 Alignment and Adjustments Display image: X-Y Coordinates: ABL Luminance Brightness: Contrast: Back raster pattern Full White Pattern x = 0.283 ± 0.02, y = 0.298 ± 0.02 Refer to 4-3-2(c) Maximum 5 ft-L, 24 ft-L 1. Check whether the color coordinates of the back raster satisfy the above spec. If they do not, return to 4-3-2 (a) and readjust all settings. 4-3-4 Focus Adjustment CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (1024 x 768) “H” character pattern Cut off point Maximum PROCEDURE 1. Adjust the Focus VR on the FBT to display the sharpest image possible. 2. Display a full white pattern. 2. Use Locktite to seal the Focus VR in position. 3. Select “Geometry” in softjig menu. 4-3-5 Color Purity Adjustment 4. Select “@7: 5-ft “ in right menu. Color purity is the absence of undesired color. Conspicuous mislanding (unexpected color in a uniform field) within the display area shall not be visible at a distance of 50 cm from the CRT surface. 5. Check whether the white coordinates of the video meet the above coordinates spec. 6. Select “@8: 24-ft “ in right menu. 7. Check whether the white coordinates of the video satisfies the above spec. If they do not, return to 4-3-2 (a) and readjust all settings. Select “Color” and click “@2: CHANNEL 2” for color ajdustment for 6500K Repeat the sequence of 9300K adjustment. The luminance values the same as 9300K, but the color coordinated of back raster and white box are : x = 0.313 ± 0.02 y = 0.329 ± 0.02 4-3-3 Luminance Uniformity Check Luminance is considered uniform only if the ratio of lowest to highest brightness areas on the screen is not less than 7.5:10. CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (1024 x 768) White flat field Cut off point at 0.06ft-L Maximum PROCEDURE Measure luminance at nine points on the display screen (see figure below). CONDITIONS Orientation: Scanning frequency: Display image: Luminance: Monitor facing east 68 kHz/85 Hz White flat field Cut off point at the center of the display area Note: Color purity adjustments should only be attempted by qualified personnel. PROCEDURE For trained and experienced service technicians only. Use the following procedure to correct minor color purity problems: 1. Make sure the display is not affected by external magnetic fields. 2. Make sure the spacing between the PCM assembly and the CRT stem is 29 mm ± 1 mm. 3. Display a green pattern over the entire display area. 4. Adjust the purity magnet rings on the PCM assembly to display a pure green pattern. (Optimum setting: x = 0.295 ± 0.015, y = 0.594 ± 0.015) Table 4-4. Color Purity Tolerances Red: x = 0.640 ± 0.015 y = 0.323 ± 0.015 Green: x = 0.295 ± 0.015 y = 0.594 ± 0.015 Blue: x = 0.142 ± 0.015 y = 0.066 ± 0.015 (For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02) Figure 4-10. Luminance Uniformity Check Locations PN17K*/PN17J* 5. When you have the PCMs properly adjusted, carefully glue them together to prevent their movement during shipping. 4-7 4 Alignment and Adjustments Memo 4-8 PN17K*/PN17J* 5 Troubleshooting 5-1 Parts Level Troubleshooting Notes: Check the following circuits. • No raster appears: Power circuit, Horizontal output circuit. • High voltage develops but no raster appears: Video output circuits. • High voltage does not develop: Horizontal output circuits. 5-1-1 No Power Supply WAVEFORMS Check and replace D601 and FH1 1 100 V (IC601, #1) Chirping noise exists? Yes Check and replace IC601. No Repeating start? CH1 P-P = 100 V Yes CH1 RMS = 350.2 V Check and replace D606. No 1 IC601 Pin 1 waveform is right? No Check and replace D614, IC601, Q602, and ZD601. No Check and replace IC201, IC301, IC401, Q402, and Q404. Yes C622 Voltage is 13 V ± 0.5V? Yes Operate normally? No Replace Main board. Yes Verify voltages. Done. PN17K*/PN17J* 5-1 5 Troubleshooting 5-1-2 DPMS Failure WAVEFORMS Check signal source H/V Sync. video level. 2 100V (IC601, #1) Make No H/V Sync. (power off mode) CH1 P-P = 100V LED blinks? No CH1 RMS = 325.8 V Check IC201 Pin 40. Yes +12 V line off? No Check IC201 Pin 6. Yes IC602 Pin 4 voltage exists? No Check IC201 Pin 6. Check and replace IC602. Yes 2 IC601 Pin 1 output voltage exists? No Refer to 5-1-1 No Power Supply. Yes Done 5-2 PN17K*/PN17J* 5 Troubleshooting 5-1-3 H_Deflection Failure 3 Does PWM output signal appear at Pin 6 (B_out) of IC401? No Yes Does DC 12V appear at Pin 10 of IC401? No Check 12 V line. Yes WAVEFORMS Check IC401. 4 Does Horizontal pluse signal appear at Pin 8 of IC401? No 3 2.00 V (IC401, #6) Check IC401. CH1 P-P = 2.00V Yes CH1 RMS = 5.868V 4 2.00V (IC401, #8) Does 110 Vp-p signal appear 5 at Collector of Q403? No Check Q403. Yes CH1 P-P = 2.00V Check Q402, Q404 and T401. CH1 RMS = 5.868V 5 20.0 V (Q404, Collector) 7-1-4 S Correction Failure CH1 P-P = 20.0 V CH1 RMS = 46.80V Check S1 ~ S4 signal. S1~S4 signals are right at each frequency block? No Check and replace IC201. Yes Check and replace Q404, Q409, Q410, Q411, Q414, Q415, Q416, Q420, and Q421. PN17K*/PN17J* 5-3 5 Troubleshooting 5-1-5 H_Lin. Failure IC201 Pin 21 voltage varies with different H_Lin. DAC values? No Replace IC201. Yes IC603 Pin 9 voltage varies with different H_Lin. DAC values? No Check +13V, –10V line. Check some parts around IC603. Yes Check Q412, Q413 and T402. 5-1-6 Invariable H_Size IC401 Pin 6 voltage varies with different B_Out DAC values? No Check and replace IC401. Yes Q402 Gate output duty varies with different B_Out DAC values? No Check some parts around Q402, IC401 Pin 3 ~ 6. 5-1-7 Abnormal H_Size IC401 Pin 11 output duty varies with different B+ offset DAC values? No WAVEFORMS Check and replace IC201. 6 200 V (Q404, Collector) Yes 6 Q404 Collector waveform is right? No Check and replace Q405, Q406, Q407, and Q408. CH1 P-P = 200V CH1 RMS = 387.2V Yes Check some parts around D409 and L401. 5-4 PN17K*/PN17J* 5 Troubleshooting 5-1-8 Side Pin or Trap Failure 7 IC401 Pin 11 output exists? No WAVEFORMS Check and replace IC401. 7 1.00 V (IC401, #11) Yes Refer to 5-1-7 Abnormal H_Size. CH1 P-P = 1.00V CH1 RMS = 3.008 V 5-1-9 Para. or Pin Balance Failure IC401 Pin 11 output varies with different DAC values? Yes Refer to 5-1-7 Abnormal H_Size. No Replace IC401. 5-1-10 Tilt Failure Check tilt connector connection IC201 Pin 20 output duty varies with different DAC values? No Check and replace IC201. Yes IC603 Pin 13 output varies with different DAC values? No Check and replace IC603. Yes Check and replace Q301 and Q302. PN17K*/PN17J* 5-5 5 Troubleshooting 5-1-11 V Deflection Failure 13V and –10V lines are on? No WAVEFORMS Refer to 5-1-1 No Power Supply 8 500 V (IC401, #12) Yes 8 IC401 Pin 12 output exists? No Check and replace IC401. CH1 P-P = 500 V 9 10.0 V (IC301, #6) Yes 9 IC301 Pin 6 output exists? CH1 RMS = 1.425 V No Check and replace some parts around IC301. Yes CH1 P-P = 10.0 V CH1 RMS = 5.06 V Check DY connector connection. 5-1-12 V Size or Position Variation Failure IC401 Pin 12 output varies with different DAC values? No Check and replace IC201 and IC401. Yes Check and replace IC301. 5-6 PN17K*/PN17J* 5 Troubleshooting 5-1-13 High Voltage Failure WAVEFORMS 3 IC401 Pin 6 OSC pulse exists? No Check and replace IC401 and +12 V line. 3 2.00 V (IC401, #6) Yes 10 Q402 Gate driving pulse exists? No Check and replace Q401 and Q423. CH1 P-P = 2.00 V CH1 RMS = 5.868 V 10 2.00 V (Q402, Gate) Yes 11 Q402 Drain pulse exists? No Check and replace D401, Q403 and L402. CH1 P-P = 2.00 V Yes CH1 RMS = 7.692V 11 50.0 V (Q402, Drain) Done 5-1-14 ABL Failure CH1 P-P = 50.0 V CH1 RMS = 73.7V Input full white pattern to monitor. IC101 Pin 8 input exists and varies with different patterns? No Check and replace IC101. Yes Check CN102. Yes T501 Pin 8 output exists? No Check and replace T501. Yes IC201 Pin 26 output exists and varies with different patterns? No Check and replace IC201. Yes Done PN17K*/PN17J* 5-7 5 Troubleshooting 5-1-15 Dynamic Focus Failure 12 IC401 Pin 32 output is right? No WAVEFORMS Replace the IC401. 12 2.00 V (IC401, #32) Yes Some parts around Q551 are right? No Replace failed part. CH1 P-P = 2.00V 13 50.0 V (T502, #6) Yes 13 T502 Pin 6 input is right? No Check and replace C432. Yes 14 T502 Pin 1 output is right? CH1 RMS = 6.124V CH1 P-P = 50.0V No CH1 RMS = 75.6V 14 100 V (T502, #1) Replace the T502. No Check the connection between FBT Focus pin and CRT Socket PCB. 5-8 CH1 P-P = 100V CH1 RMS = 124.0V PN17K*/PN17J* 5 Troubleshooting 5-1-16 No Video WAVEFORMS Check signal cable and connection. 15 1.00V (IC101 #12,14,16) 15 IC101 Pin 12, 14 and 16 inputs are right? No Check the signal cable connection. Yes 16 IC101 Pin 18, 21 and 24 outputs are right? CH1 P-P = 1.00V No CH1 RMS = 2.452V 16 1.00V (IC101 #18,21,24) Check I2C bus and +12V line. Yes 17 IC103 Pin 1, 2 and 3 outputs are right? No Check +12V, +72 V line. Check and replace IC103. CH1 P-P = 1.00V CH1 RMS = 2.792V 17 20.0V (IC103, #1, 2, 3) Yes Cathode DC levels are right? No Check +72V line. Check and replace QR01, QR02, QG01, QG02, QB01, and QB02. CH1 P-P = 20.0V CH1 RMS = 40.52V Yes G2 voltage is right? No Check G2 wire, CRT Socket board and FBT. Yes Change CRT. Done. PN17K*/PN17J* 5-9 5 Troubleshooting 5-1-17 Micom Failure IC201 Pin 11 input voltage is 5V? No WAVEFORMS Check IC604. 18 1.00 V (IC201, #13, 14) Yes 18 IC201 Pin 13 and 14 inputs are right? No Check C202, C203 and X201. CH1 P-P = 1.00 V CH1 RMS = 2.108V Yes IC201 Pin 18 input is right? No Check IC605. Yes All in/output values are right? No Replace IC201. Yes Done 5-10 PN17K*/PN17J* 5 Troubleshooting 5-1-18 OSD Failure WAVEFORMS Check CN104 and connector Ass’y. 19 1.00 V (IC101, #32) Yes 19 IC101 Pin 32 input is right? No Check amd replace Q102. Check CN102 Pin 14. Yes 20 IC101 Pin 1 input is right? CH1 P-P = 1.00V No CH1 RMS = 4.516V 20 1.00 V (IC101, #1) Check CN102 Pin 8. Yes IC101 Pin 29 and 30 inputs are right? No Check IC201 Pin 41 and 42. CH1 P-P = 1.00V CH1 RMS = 5.024V 21 1.00 V (IC101, #18,21,24) Yes 21 IC101 Pin 18, 21 and 24 outputs are right? No Check and replace IC101. CH1 P-P = 1.00V CH1 RMS = 2.580V Yes Check and replace IC103. Done PN17K*/PN17J* 5-11 5 Troubleshooting 5-1-19 User Control Failure Does the DC level change at Pin 36 of IC201 when you push the button S/W? No Check the button. (SW201 ~ SW204) Yes Check IC201. 5-1-20 Degaussing Failure Check degaussing connector. RL601 operation is right? Yes Check D-coil and TH601. No Q601 base input is right? Yes Check and replace Q601. No IC201 Pin 4 output is right? No Check and replace IC201. Yes Done 5-12 PN17K*/PN17J* 5 Troubleshooting 5-2 General Troubleshooting 5-2-1 No Picture LED blinks? Yes Refer to 5-2-2 Shut down. No LED is green color? Yes Check Micom. No Check G2 voltage, high voltage and R, G, B cathode voltage. 5-2-2 Shut Down Blinking LED’s? No Check power supply. Yes Scan failure? Yes Check horizontal, vertical deflection system and check power supply secondary voltages. No Video failure? Yes Check Video board. No Check and replace IC201. Done PN17K*/PN17J* 5-13 5 Troubleshooting 5-2-3 Missing Color WAVEFORMS Proper Video levels are on CN101 (D-Sub) Pin 1, 3 and 5? No Check signal generator. 22 10.0 V (R,G,B, Video) Yes 22 Proper Video signal is on all cathodes? No Refer to 5-1-16 No Video. CH1 P-P = 10.0V CH1 RMS = 17.02V Yes Proper DC voltage is on all cathodes? No Check IC101 Pin 17, 20 and 23. Check QR01, QR02, QG01,. QG02, QB01, and QB02. Yes G2 voltage is right? No Check Q501 and D520. Yes Heater voltage is right? No Check D608, Q604 and T601. Yes G1 voltage is right? No Check D504, Q502 and T501. Yes Replace CRT. Yes Done 5-14 PN17K*/PN17J* 5 Troubleshooting 5-2-4 Visible Retrace Check white balance adjustment. G2 voltage is right? No WAVEFORMS Check D502, D517 and Q501. 23 5.00V (Q303, Collector) Yes Blank pulse is on Pin 17 of IC401? No Check IC401. CH1 P-P = 5.00V 24 20.00V (CRT Socket, G1) Yes 23 V_FLB pulse is on Collector of Q303? No Check Q303. Yes 24 Does approve the Vertical pulse on the CRT Socket G1? CH1 RMS = 28.33V CH1 P-P = 20.0V No CH1 RMS = 66.68V Check CN102 and CN201. Yes Done PN17K*/PN17J* 5-15 5 Troubleshooting 5-2-5 Unsynchronized Image Check input signals Pin 2 and 3 of CN202. Signals are right? No Check Video Cable Yes Signals at Pin 28 and 29 of IC201 are right? No Check IC201. Yes Signals at Pin 14 and 15 of IC401 are right? No Check IC401 Yes Check circuits on Main board. Done 5-16 PN17K*/PN17J* 5 Troubleshooting 5-2-6 Misconvergence Try readjusting convergence. The convergence is now within spec.? Yes Done No Readjust convergence. The convergence is now within spec.? Yes Done No Change CRT and readjust convergence. Done PN17K*/PN17J* 5-17 5 Troubleshooting 5-2-7 Poor Focus Adjust focus VR of FBT. Improved focus? Yes Aging monitor and check for focus change. No Refer to 5-1-15 Dynamic Focus Failure. No Check focus leads from FBT to CRT Socket. Check the CRT Socket. Dynamic focus circuit is right? Yes Replace the CRT and verify focus. 5-2-8 Purity Failure Degaussing Purity is right? Yes Done No Degaussing circuit is right? No Refer to 5-1-20 Degaussing Failure. Yes Replace CRT and verify purity. 5-18 PN17K*/PN17J* 6 Exploded View and Parts List 6-1 PN17KT/JT PN17K*/PN17J* 6-1 6 Exploded View & Parts List 6-2 PN17KO/JO 6-2 PN17K*/PN17J* 6 Exploded View and Parts List 6-1-1 Front Cover & CRT Ass’y (PN17KT/JT) PN17K*/PN17J* 6-3 6 Exploded View & Parts List 6-1-2 Chassis & Stand Ass’y (PN17KT/JT) 6-4 PN17K*/PN17J* 6 Exploded View & Parts List 6-1-3 Rear Ass’y (PN17KT/JT) PN17K*/PN17J* 6-5 6 Exploded View & Parts List 6-2-1 Front Cover & CRT Ass’y (PN17KO/JO) 6-6 PN17K*/PN17J* 6 Exploded View & Parts List 6-2-2 Chassis & Stand Ass’y (PN17KO/JO) PN17K*/PN17J* 6-7 6 Exploded View & Parts List 6-2-3 Rear Ass’y (PN17KO/JO) 6-8 PN17K*/PN17J* 7 Electrical Parts List 7-1 Main PCB Parts (PN17K*) Loc. No. Code No. Description Specification Remarks B/PCB+LMF BOTTOM C409 C430 C601 C602 C608 CIS CIS CIS CIS CIS CIS CIS CIS CIS CN201 CN202 CN203 CN403 CN601 D406 D601 D609 FBT FBT+H/S FUSE IC201 IC201_SOCK IC401 IC602 IC604 JW1 JW2 JW3 JW4 L401 L402 L403 L601 OP201 RL601 S/BTM+PCB SH/BTM+AC/SOCK SW401 SW601 T401 T402 T501 T502 T601 T602 TH601 TH602 70KHZ BD301 BD401 BD402 BD403 BD555 BD601 6003-000010 2001-000066 2306-000147 2306-000249 2301-001195 2301-001195 2401-003391 BH39-00145A BH39-00242A BH68-00001A BH71-00110A BH72-00025A BH72-00026A BH72-00261A BH73-60304C BH46-00002M 3711-003895 3711-003873 BH39-00131A 3711-003989 3721-001028 0402-001025 0402-001407 0402-000005 6502-000001 6003-000122 3601-000004 0903-001166 3704-001071 1204-001509 1203-000165 1203-000001 BH39-00210A BH39-00210A BH39-40305Y BH39-40306C BH27-00005A BH27-00022A BH27-20342U BH27-00061A 0601-001147 3501-001111 6003-000010 6003-000010 3406-000002 3403-001050 BH26-00027A BH26-00028A BH26-00026A BH26-00057A BH26-00059A BH26-30302S 1404-000002 1404-001020 BH39-40305U 3301-000011 3301-000011 3301-000011 3301-000011 3301-000011 3301-000011 SCREW-TAPTITE R-CARBON(S) C-FILM,MPPF C-FILM,MPPF C-FILM,MPPF C-FILM,MPPF C-AL CBF SIGNAL CBF HARNESS LABEL/MARK-CDT SHIELD-BOTTOM GUIDE-POWER SHAFT-POWER SHEET-LMF RUBBER-SUPPORT MICOM-S/W,PN17KT CONNECTOR-HEADER CONNECTOR-HEADER CBF-HARNESS CONNECTOR-HEADER PLUG-AC POWER DIODE-RECTIFIER DIODE-BRIDGE DIODE-RECTIFIER CABLE CLAMP SCREW-TAPTITE FUSE-CARTRIDGE IC-MICROCONTROLLER SOCKET-IC IC-HOR./VER.PROCESSO IC-POSI.ADJUST REG. IC-POSI.FIXED REG. CBF-HARNESS CBF-HARNESS CBF-HARNESS CBF-HARNESS COIL-CHOKE COIL-CHOKE COIL-CHOKE COIL FILTER LED RELAY-POWER SCREW-TAPTITE SCREW-TAPTITE SWITCH-ROTARY SWITCH-PUSH TRANS-HOR.DRIVE TRANS-H.LINEARITY TRANS-FBT TRANS-FOCUS TRANS-POWER TRANS-SYNC. THERMISTOR-PTC THERMISTOR-NTC CBF HARNESS CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 10KOHM,5%,1/2W,AA,TP,2.4X6.4MM 1uF,5%,250V,BK,26x24x15,22.5mm 680nF,5%,250V,TP,26x20.5x12,20 150nF,10%,275VAC,BK,26x16.5x7, 150nF,10%,275VAC,BK,26x16.5x7, 220uF,20%,450V,GP,BK,25x50,10 ATT,1500MM,15P/6P,7P,IVORY(IV01),-,D-SUB/MALE DB5907,UL1032,UL/CSA,1P,290MM,RED,AWG22,YFH800,YPT-018,-,-,-,-,-,-,CBF-GND ASS’Y ART-PAPER 100G,-,WHT,BLK,-,ALL,CDT PN15VT,SECC ,T1.0,-,-,CDA4507,ABS+PC,5V,IV16,-,CDA4507,ABS+PC,5V,IV16,-,IB10LO,AL+PET,-,-,-,-,-,DP15LT,CR V0,GRAY,-,14*7*10,-,PN17KT(PHOEINX),-,-,-,-,-,BOX,13P,1R,2mm,STRAIGHT,SN BOX,7P,1R,2mm,STRAIGHT,SN 2P,80MM,BLU/WHT/YEL,UL1007,AWG26,SMP250-02/YBNH200-02 NOWALL,4P,1R,8mm,STRAIGHT,SN 3P,-,-,NI ERD07-15,1.5KV,1.5A,-,TP G2SB60,600V,1.5A,SIP-4,BK 31DF4,400V,3A,DO-201AD,BK DAWH-5NB,D15,L35,NTR,NYLON66 BH,+,B,M4,L12,ZPC(YEL),SWRCH18 250V,3.15A,SLOW-BLOW,CERAMIC,5x20mm 3P8629,8Bit,DIP,42P,600MIL,12MHz,ST,CMOS,PLASTIC,5V,-,-40to+85C,464BYTE,32K,8Bit 42P,DIP,SN,1.778mm TDA4859,DIP,32P,400MIL,PLASTIC,16V,-,-20TO+70CC,ST,H/V DEF. PROCESSOR 78R12,TO-220,3P,-,-,12V,-,0to+ 7805,TO-220,3P,-,PLASTIC,4.8/5 DP17M**,UL1015,UL/CSA,-,60MM,BLK,AWG22,-,-,-,-,-,-,-,-,CBF-JUMPER WIRE DP17M**,UL1015,UL/CSA,-,60MM,BLK,AWG22,-,-,-,-,-,-,-,-,CBF-JUMPER WIRE ,110MM,BLK,1015,AWG22,-,-,-,-, ,60MM,BLK,1015,AWG22,-,-,-,-,120UH,10%,AR-06*30,BULK,-,100UH,+/-10%,DR1523(C:9.8),BK,-,-,8.2MH(250KHz),10%,DR8*11,-,-,-,-,10.5OHM,-,-,-,BULK -,33.0mH,0.1ohm,72Ts,28.*28,-,BK,SQE-2828,3A,-,ROUND,GRN,4.75mm,565nm 12Vdc,250mW,5A,1FormA,15mS,5mS BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 36Vdc,200mA,SP3T,30V,0.3A,SPDT,ON-OFF,PC BORD T 35.0MH,-,EI 1916,PL-3,-,310UH,5.2UH,6P,DR1425(C:5.0),YL-81,5.2UH/68.0MH,-,HL-1425E 1.1MH,-,3763SU,SM9C,-,-,3.8MH MIN,10P,EI-2218,(SB-5S),SB-5S,3.8MH/225MH MIN,40UH MAX,350UH,18P,EER 3541,PL3,PM2,7.0UH MAX.,0.22OHM,3-1(250UH),-,-,SB-5S,UU1116,39ohm,20%,-,-,TR,RECT,8ohm,15%,-,17mW/C,BK 52MM,AWG22(0.6PI),-,-,AWG22(0. AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G SNA PN17K*/PN17J* SNA SNA SNA SNA SNA SNA SNA SNA SNA ! SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA ! ! SNA SNA SNA SNA SNA SNA SNA 7-1 7 Electrical Parts List Loc. No. BD602 BD603 C201 C202 C203 C204 C205 C206 C207 C209 C210 C211 C212 C213 C214 C215 C216 C217 C220 C225 C301 C302 C305 C306 C307 C308 C309 C310 C311 C312 C313 C401 C402 C403 C404 C405 C406 C407 C408 C410 C411 C412 C413 C414 C415 C416 C417 C419 C420 C421 C423 C425 C426 C427 C429 C431 C432 C433 C434 C435 C436 7-2 Code No. Description 3301-000011 3301-000011 2401-000025 2201-000389 2201-000389 2401-002075 2401-000603 2401-000050 2401-002075 2401-002075 2401-002075 2201-000146 2201-000017 2401-000029 2401-000025 2201-000146 2401-000603 2202-002009 2401-000037 2401-002075 2301-000010 2305-001041 2401-000037 2401-000856 2305-000237 2301-000004 2202-000252 2301-000519 2301-001027 2401-001016 2301-000010 2301-000312 2305-000665 2301-000148 2301-000004 2201-000823 2301-000013 2401-000540 2201-000556 2401-000037 2301-000180 2301-000519 2401-001012 2401-001334 2401-001218 2301-000010 2301-000321 2303-000165 2301-001305 2301-001341 2401-000603 2306-000131 2401-000603 2306-000171 2401-000603 2306-000179 2305-001033 2305-001003 2401-001016 2201-002079 2201-000672 CORE-FERRITE BEAD CORE-FERRITE BEAD C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-AL C-AL C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-CERAMIC,DISC C-AL C-CERAMIC,MLC-AXIAL C-AL C-AL C-FILM,PEF C-FILM,MPEF C-AL C-AL C-FILM,MPEF C-FILM,PEF C-CERAMIC,MLC-AXIAL C-FILM,PEF C-FILM,PEF C-AL C-FILM,PEF C-FILM,PEF C-FILM,MPEF C-FILM,PEF C-FILM,PEF C-CERAMIC,DISC C-FILM,PEF C-AL C-CERAMIC,DISC C-AL C-FILM,PEF C-FILM,PEF C-AL C-AL C-AL C-FILM,PEF C-FILM,PEF C-FILM,PPF C-FILM,PPF C-FILM,PPF C-AL C-FILM,MPPF C-AL C-FILM,MPPF C-AL C-FILM,MPPF C-FILM,MPEF C-FILM,MPEF C-AL C-CERAMIC,DISC C-CERAMIC,DISC Specification AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G 100uF,20%,16V,GP,TP,6.3x11,5 0.022nF,5%,50V,NP0,TP,5x3,5 0.022nF,5%,50V,NP0,TP,5x3,5 4.7uF,20%,50V,GP,TP,5x11,5 1uF,20%,50V,GP,TP,5x11,5 10uF,20%,16V,GP,TP,5x11,2.5 4.7uF,20%,50V,GP,TP,5x11,5 4.7uF,20%,50V,GP,TP,5x11,5 4.7uF,20%,50V,GP,TP,5x11,5 0.1nF,5%,50V,SL,TP,5x3.5,5 1nF,10%,50V,Y5P,TP,5x3.5,5 10uF,20%,100V,GP,TP,6.3x11,5 100uF,20%,16V,GP,TP,6.3x11,5 0.1nF,5%,50V,SL,TP,5x3.5,5 1uF,20%,50V,GP,TP,5x11,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 470uF,20%,16V,GP,TP,8x11.5,5 4.7uF,20%,50V,GP,TP,5x11,5 100nF,5%,100V,TP,11.5x12.5mm,5 220nF,5%,63V,TP,7.5x4.5x13.5,5 470uF,20%,16V,GP,TP,8x11.5,5 220uF,20%,35V,WT,TP,10x20,5 1uF,5%,63V,TP,7.5x15.5mm,5mm 2.2nF,5%,100V,TP,5.5X10X2.9,5m 4.7nF,10%,50V,X7R,TP,2.5x4.3,3.3nF,5%,100V,TP,5.8x3x12.5,5m 15nF,10%,250V,TP,9.5x12x4.5,5m 3.3UF,20%,50V,BP,TP,5X11,5 100nF,5%,100V,TP,11.5x12.5mm,5 8.2nF,5%,100V,TP,6x12.5mm,5mm 100nF,5%,63V,TP,7.5x4.0x5.0mm, 10nF,5%,100V,TP,7x3.2x7mm,5mm 2.2nF,5%,100V,TP,5.5X10X2.9,5m 0.27nF,5%,50V,SL,TP,8x3.5,5 4.7nF,5%,100V,TP,10.5x12.5x6.5 150uF,20%,63V,LZ,TP,10x25,5 0.47nF,10%,500V,Y5P,TP,5.5x3,5 470uF,20%,16V,GP,TP,8x11.5,5 18nF,5%,100V,TP,7.2x4.0x7.5mm, 3.3nF,5%,100V,TP,5.8x3x12.5,5m 3.3UF,20%,50V,BP,TP,16X25,7.5 470nF,20%,50V,GP,TP,5x11,2.5 4.7uF,20%,100V,WT,TP,5x11,5 100nF,5%,100V,TP,11.5x12.5mm,5 8.2nF,5%,100V,TP,7x3.2x7mm,5mm 2.5nF,5%,1.6kV,TP,21x6.8x12.6mm,7.5 2.2NF,3%,1.6KV,TP,22X15.5X8.5MM,7.5 3.3nF,5%,630V,TP,17.4x10x5.4mm,7.5 1uF,20%,50V,GP,TP,5x11,5 150nF,5%,250V,TP,19x16x7.5,7.5 1uF,20%,50V,GP,TP,5x11,5 270nF,5%,250V,TP,21.5x12.5mm,7 1uF,20%,50V,GP,TP,5x11,5 300nF,5%,250V,TP,20x18.5x10.5, 15nF,10%,250V,TP,13X9.0X4.5mm, 10nF,5%,250V,TP,13x4.5x9mm,7.5 3.3UF,20%,50V,BP,TP,5X11,5 0.15nF,10%,500V,Y5P,TP,6.3x4mm,5 0.82nF,10%,500V,Y5P,TP,6.5x3,5 Remarks SNA SNA ! ! PN17K*/PN17J* 7 Electrical Parts List Loc. No. C445 C446 C447 C448 C450 C501 C502 C503 C504 C505 C506 C507 C508 C509 C510 C511 C512 C513 C514 C530 C551 C552 C557 C603 C604 C607 C609 C610 C611 C612 C613 C614 C615 C616 C617 C618 C619 C620 C621 C622 C623 C624 C625 C626 C627 C630 C631 C635 CN304 CN603 D301 D401 D402 D403 D404 D405 D407 D410 D411 D412 D413 Code No. Description 2201-000019 2201-000647 2201-000476 2305-000428 2305-000237 2301-000016 2301-000016 2401-000603 2301-000004 2401-000059 2201-000019 2201-000285 2401-002267 2401-002267 2301-000020 2301-000519 2301-000148 2201-000291 2401-001334 2201-000291 2401-000050 2201-000132 2401-001643 2201-000024 2201-000024 2202-002009 2401-000971 2301-000284 2401-000613 2401-000613 2201-000129 2201-000019 2201-000291 2201-000023 2201-000023 2401-000039 2201-000469 2401-000540 2401-001585 2401-000039 2401-000039 2201-000210 2305-001041 2401-000037 2401-000142 2401-001561 2202-002009 2201-000019 3711-000197 3711-000217 0402-000274 0402-000274 0402-000006 0402-000006 0402-000006 0402-000208 0402-001118 0402-000546 0402-000546 0402-000546 0402-000546 C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-FILM,MPEF C-FILM,MPEF C-FILM,PEF C-FILM,PEF C-AL C-FILM,PEF C-FILM,MPEF C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-FILM,PEF C-FILM,PEF C-FILM,PEF C-CERAMIC,DISC C-AL C-CERAMIC,DISC C-AL C-CERAMIC,DISC C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL C-AL C-FILM,PEF C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-CERAMIC,DISC C-AL C-AL C-AL C-AL C-CERAMIC,DISC C-FILM,MPEF C-AL C-AL C-AL C-CERAMIC,MLC-AXIAL C-CERAMIC,DISC CONNECTOR-HEADER CONNECTOR-HEADER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER PN17K*/PN17J* Specification 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 0.068nF,5%,500V,NP0,TP,8x3.5mm,5 0.033nF,10%,500V,SL,TP,5.5x3,5 47nF,5%,250V,TP,11x9x4.5,5mm 1uF,5%,63V,TP,7.5x15.5mm,5mm 22nF,5%,100V,TP,7.2x4.5x9.0mm, 22nF,5%,100V,TP,7.2x4.5x9.0mm, 1uF,20%,50V,GP,TP,5x11,5 2.2nF,5%,100V,TP,5.5X10X2.9,5m 100nF,5%,63V,GP,-,5x11,5 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 1nF,10%,1kV,Y5P,TP,8x5,5 2.2uF,20%,250V,GP,TP,8x11.5,5 2.2uF,20%,250V,GP,TP,8x11.5,5 27nF,5%,100V,TP,7.3x4x12.5mm,5 3.3nF,5%,100V,TP,5.8x3x12.5,5m 10nF,5%,100V,TP,7x3.2x7mm,5mm 1nF,10%,500V,Y5P,TP,7.5x3.5,5 470nF,20%,50V,GP,TP,5x11,2.5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 10uF,20%,16V,GP,TP,5x11,2.5 0.1nF,10%,500V,Y5P,TP,6.5x3,5 0.68uF,20%,50V,GP,TP,5x11mm,5 4.7nF,20%,250VAC,Y5U,TP,16x7,7 4.7nF,20%,250VAC,Y5U,TP,16x7,7 100nF,+80-20%,50V,Y5V,TP,2.3X3 22uF,20%,50V,WT,TP,6x11mm,5mm 47nF,5%,100V,TP,8.5x12.5mm,5mm 1uF,20%,50V,WT,TP,5x11,5 1uF,20%,50V,WT,TP,5x11,5 0.1nF,10%,1kV,Y5P,TP,7x4,5 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 2.2nF,20%,125V,Y5U,TP,11x7,5 2.2nF,20%,125V,Y5U,TP,11x7,5 1000uF,20%,16V,GP,TP,10x16,5 0.33nF,10%,500V,Y5P,TP,5.5x3,5 150uF,20%,63V,LZ,TP,10x25,5 47uF,20%,50V,WT,TP,8x11.5,5 1000uF,20%,16V,GP,TP,10x16,5 1000uF,20%,16V,GP,TP,10x16,5 0.12NF,10%,1KV,Y5P,TP,6.3X4MM,5 220nF,5%,63V,TP,7.5x4.5x13.5,5 470uF,20%,16V,GP,TP,8x11.5,5 1000uF,20%,16V,WT,TP,10x20,5 47uF,20%,35V,WT,TP,8x11.5,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 1WALL,3P,1R,2.5mm,STRAIGHT,SN 1WALL,3P,1R,3.96mm,STRAIGHT,SN UF4004,400V,1A,DO-41,TP UF4004,400V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP EK-04,40V,1.5A,DO-41 UF1G,400V,1.2A,DO-204AL,TP TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP Remarks ! SNA SNA 7-3 7 Electrical Parts List Loc. No. D420 D421 D422 D431 D432 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D515 D516 D517 D518 D519 D602 D604 D605 D606 D607 D608 D610 D611 D612 D614 D615 D616 D617 EY301 EY302 EY401 EY402 EY403 EY501 EY502 EY503 EY504 EY505 EY506 EY507 EY508 EY510 EY601 EY602 EY603 EY604 EY605 EY606 EY607 EY608 EY609 EY610 FH1 7-4 Code No. Description 0401-000005 0401-000005 0401-000004 0401-000005 0402-000546 0401-000005 0402-000017 0402-000017 0402-000017 0401-000004 0402-000546 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0402-000017 0401-000005 0401-000005 0401-000005 0402-000017 0401-000004 0401-000005 0401-000005 0402-000012 0402-000012 0402-000546 0401-000005 0402-000274 0402-000012 0402-001194 0402-000274 0402-000546 0401-000005 0401-000005 0402-001039 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000001 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002 6042-000001 6042-000001 6042-000001 6042-000001 6042-000001 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000002 3602-000001 DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET FUSE-CLIP Specification 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP RGP02-12,1200V,0.5A,DO-204AL,T RGP02-12,1200V,0.5A,DO-204AL,T RGP02-12,1200V,0.5A,DO-204AL,T 1SS244,250V,625mA,DO-34,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP RGP02-12,1200V,0.5A,DO-204AL,T 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP RGP02-12,1200V,0.5A,DO-204AL,T 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP UF4007,1KV,1A,DO-41,TP UF4007,1KV,1A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP UF4004,400V,1A,DO-41,TP UF4007,1KV,1A,DO-41,TP UG2D,200V,2A,DO-204AC,TP UF4004,400V,1A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP SB020,20V,600mA,MPG06,TP ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH -,-,30mohm Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA PN17K*/PN17J* 7 Electrical Parts List Loc. No. GT501 GT603 GT604 IC202 IC603 IC605 J19 JP1 JP10 JP11 JP12 JP13 JP14 JP15 JP16 JP17 JP18 JP2 JP20 JP22 JP23 JP24 JP25 JP26 JP27 JP28 JP29 JP3 JP31 JP32 JP33 JP34 JP35 JP36 JP37 JP38 JP39 JP4 JP40 JP41 JP42 JP43 JP44 JP45 JP46 JP47 JP48 JP5 JP50 JP51 JP52 JP53 JP54 JP55 JP56 JP57 JP58 JP59 JP6 JP60 JP61 Code No. BH71-40300A BH71-40300A BH71-40300A 1103-001149 1201-000229 1203-000495 BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U PN17K*/PN17J* Description PIN-HINGE PIN-HINGE PIN-HINGE IC-EEPROM IC-OP AMP IC-RESET CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS Specification -,BRASS,D2.36,SN,HEAT/SINK -,BRASS,D2.36,SN,HEAT/SINK -,BRASS,D2.36,SN,HEAT/SINK 524C80D41,4KBit,DIP,8P,300MIL,10mS,5V,10%,PLASTIC,-25to+70C,10uA,CMOS,ST 324,DIP,14P,300MIL,QUAD,100V/m 7045,T0-92,3P,-,PLASTIC,4.3/4. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA 7-5 7 Electrical Parts List Loc. No. JP63 JP64 JP65 JP67 JP68 JP7 JP70 JP71 JP72 JP76 JP8 JP82 JP84 JP85 JP9 MP1.0 Q301 Q302 Q303 Q401 Q405 Q406 Q407 Q412 Q413 Q414 Q415 Q416 Q423 Q501 Q502 Q503 Q551 Q601 Q602 Q604 Q608 Q609 Q610 R200 R201 R202 R203 R204 R206 R207 R208 R209 R210 R211 R212 R213 R214 R215 R216 R217 R218 R220 R221 R222 R223 7-6 Code No. BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH41-00136A 0501-000586 0501-000303 0501-000413 0501-000122 0501-000303 0501-000303 0501-000140 0501-000404 0501-000321 0501-000586 0501-000586 0501-000586 0501-000303 0501-000143 0501-000143 0501-000303 0501-000413 0501-000586 0501-000122 0501-000404 0501-000010 0501-002228 0501-000586 2001-000869 2001-000786 2001-000290 2001-000734 2001-000734 2001-000515 2001-000869 2001-000869 2001-000734 2001-000472 2001-000878 2001-000660 2001-000429 2001-000429 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000734 2001-000734 2001-000038 Description CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS PCB MAIN TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON Specification 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. PN17KT,FR1,1,-,1.6T,247*247,-,-,-,KSC945,NPN,250mW,TO-92,TP,120-240 KSA733,PNP,250mW,TO-92,TP,120-240 KSP44,NPN,625mW,TO-92,TP,50-200 2N3904,NPN,625mW,TO-92,TP,100-300 KSA733,PNP,250mW,TO-92,TP,120-240 KSA733,PNP,250mW,TO-92,TP,120-240 2N5551,NPN,625mW,TO-92,TP,80-250 KSD1616-Y,NPN,750mW,TO-92,TP,135-270 KSB1116-Y,PNP,750mW,TO-92,TP,135-270 KSC945,NPN,250mW,TO-92,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KSA733,PNP,250mW,TO-92,TP,120-240 2N6520,PNP,625mW,TO-92,TP,30-200 2N6520,PNP,625mW,TO-92,TP,30-200 KSA733,PNP,250mW,TO-92,TP,120-240 KSP44,NPN,625mW,TO-92,TP,50-200 KSC945,NPN,250mW,TO-92,TP,120-240 2N3904,NPN,625mW,TO-92,TP,100-300 KSD1616-Y,NPN,750mW,TO-92,TP,135-270 KSC1008,NPN,800mW,TO-92,TP,120-240 KTA1281,PNP,1000mW,TO-92L,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 220OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 390OHM,5%,1/4W,AA,TP,2.4X6.4MM Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA ! ! PN17K*/PN17J* 7 Electrical Parts List Loc. No. R224 R225 R229 R230 R235 R236 R239 R301 R302 R303 R304 R306 R307 R308 R309 R310 R311 R312 R315 R316 R317 R318 R319 R320 R321 R322 R323 R324 R325 R326 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R415 R416 R417 R418 R419 R420 R422 R423 R424 R425 R426 R427 R428 R429 R430 R431 R432 R433 Code No. 2001-000869 2001-000869 2001-000281 2001-000290 2001-000472 2001-000290 2001-000290 2001-000869 2004-000580 2001-000890 2001-000890 2004-001022 2001-001048 2001-000037 2004-004014 2004-001136 2001-000890 2001-000812 2004-004014 2001-000281 2001-000561 2001-000766 2001-000947 2001-000331 2001-000591 2001-000890 2001-000022 2001-000660 2003-000805 2003-000805 2001-000869 2004-001226 2004-000498 2001-000591 2001-000522 2001-000109 2001-000429 2001-000812 2001-000105 2001-001096 2001-000290 2001-001038 2001-001038 2003-000432 2001-000107 2001-000331 2001-000221 2001-000004 2001-000395 2001-001006 2001-000258 2004-000284 2001-000119 2001-000110 2001-000591 2003-000483 2001-000052 2001-001078 2003-000407 2001-000020 2003-000769 PN17K*/PN17J* Description R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-METAL R-CARBON(S) R-CARBON(S) R-METAL R-METAL R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON R-METAL OXIDE(S) R-METAL OXIDE(S) R-CARBON R-METAL R-METAL R-CARBON R-CARBON R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON R-CARBON(S) R-CARBON(S) R-METAL OXIDE(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON(S) R-CARBON(S) R-METAL OXIDE(S) R-CARBON(S) R-METAL OXIDE(S) Specification 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 22Kohm,1%,1/4W,AA,TP,2.4x6.4mm 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4m 1.2OHM,5%,1/2W,AA,TP,2.4X6.4MM 330OHM,5%,1/2W,AA,TP,2.4X6.4MM 2.4ohm,1%,1/4W,AA,TP,2.4x6.4mm 6.8Kohm,1%,1/4W,AA,TP,2.4x6.4m 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.4ohm,1%,1/4W,AA,TP,2.4x6.4mm 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 27KOHM,5%,1/4W,AA,TP,2.4X6.4MM 43KOHM,5%,1/8W,AA,TP,1.8X3.2MM 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 33OHM,5%,1/2W,AA,TP,2.4X6.4MM 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM 82ohm,5%,1W,AA,TP,3.3x9mm 82ohm,5%,1W,AA,TP,3.3x9mm 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 750ohm,1%,1/4W,AA,TP,2.4x6.4mm 2.7Kohm,1%,1/4W,AA,TP,2.4x6.4m 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM 470OHM,5%,1/2W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.5KOHM,5%,1/4W,AA,TP,2.4X6.4MM 2.2OHM,5%,1/2W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 0.56OHM,5%,1/2W,AA,TP,2.4X6.4MM 0.56OHM,5%,1/2W,AA,TP,2.4X6.4MM 1.5Kohm,5%,3W,AA,TP,6x16mm 150KOHM,5%,1/2W,AA,TP,2.4X6.4MM 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 200KOHM,5%,1/8W,AA,TP,1.8X3.2MM 180KOHM,5%,1/4W,AA,TP,2.4X6.4MM 82OHM,5%,1/8W,AA,TP,1.8X3.2MM 1.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 12Kohm,1%,1/4W,AA,TP,2.4x6.4mm 680OHM,5%,1/4W,AA,TP,2.4X6.4MM 10OHM,5%,1/4W,AA,TP,2.4X6.4MM 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM 120ohm,5%,3W,AA,TP,6x16mm 3.3KOHM,5%,1/2W,AA,TP,2.4X6.4MM 15KOHM,5%,1/2W,AA,TP,2.4X6.4MM 0.6ohm,5%,2W,AA,TP,4x12mm 22OHM,5%,1/2W,AA,TP,2.4X6.4MM 680ohm,5%,3W,AA,TP,6x16mm Remarks ! ! ! 7-7 7 Electrical Parts List Loc. No. R434 R435 R436 R437 R438 R439 R440 R441 R443 R444 R445 R446 R447 R448 R449 R450 R451 R452 R453 R454 R458 R459 R460 R500 R501 R502 R503 R504 R505 R506 R507 R508 R509 R510 R511 R512 R513 R514 R515 R516 R518 R519 R524 R525 R526 R527 R529 R530 R531 R532 R551 R552 R553 R554 R555 R556 R560 R561 R570 R600 7-8 Code No. 2001-000449 2001-000786 2001-000449 2001-000786 2001-000449 2001-000786 2001-000947 2001-000411 2003-000578 2001-000739 2001-001079 2001-000117 2003-000777 2003-000777 2001-000211 2001-000522 2001-000290 2001-000290 2001-000290 2003-000650 2003-000650 2001-000938 2003-000724 2001-000435 2001-000472 2004-000979 2001-000449 2001-000008 2001-000008 2004-000643 2004-000216 2002-000121 2002-000121 2001-000837 2001-000478 2001-000786 2001-000087 2002-001069 2001-000546 2002-001056 2001-001031 2001-000356 2001-000660 2001-000273 2001-000702 2001-000011 2001-000429 2001-000397 2001-000508 2001-000432 2001-000530 2001-000495 2001-000642 2002-001049 2001-000042 2001-000613 2002-000121 2001-000432 2001-000085 2001-001129 Description R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON(S) R-CARBON(S) R-METAL OXIDE(S) R-METAL OXIDE(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL OXIDE(S) R-METAL OXIDE(S) R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON R-METAL R-METAL R-COMPOSITION R-COMPOSITION R-CARBON R-CARBON R-CARBON R-CARBON(S) R-COMPOSITION R-CARBON R-COMPOSITION R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-COMPOSITION R-CARBON R-CARBON R-COMPOSITION R-CARBON R-CARBON(S) R-CARBON(S) Specification 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM 220ohm,5%,2W,AA,TP,4x12mm 4.7MOHM,5%,1/8W,AA,TP,1.8X3.2MM 15OHM,5%,1/2W,AA,TP,2.4X6.4MM 68OHM,5%,1/2W,AA,TP,2.4X6.4MM 68ohm,5%,2W,AA,TP,4x12mm 68ohm,5%,2W,AA,TP,4x12mm 1OHM,5%,1/4W,AA,TP,2.4X6.4MM 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,2W,AA,TP,4x12mm 330ohm,5%,2W,AA,TP,4x12mm 68OHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6ohm,5%,3W,AA,TP,6x16mm 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47Kohm,1%,1/4W,AA,TP,2.4x6.4mm 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM 270Kohm,1%,1/4W,AA,TP,2.4x6.4m 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm 1Mohm,10%,1/2W,AA,TP,3.5x9.5mm 1Mohm,10%,1/2W,AA,TP,3.5x9.5mm 51KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7OHM,5%,1/4W,AA,TP,2.4X6.4MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 120KOHM,5%,1/2W,AA,TP,2.4X6.4MM 51Kohm,5%,1/4,AA,TP,2.5x6.5mm 270KOHM,5%,1/4W,AA,TP,2.4X6.4MM 180Kohm,2%,1/4W,AA,TP,2.5x6.5mm 91KOHM,5%,1/8W,AA,TP,1.8X3.2MM 150KOHM,5%,1/8W,AA,TP,1.8X3.2MM 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM 39KOHM,5%,1/8W,AA,TP,1.8X3.2MM 75KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 180KOHM,5%,1/8W,AA,TP,1.8X3.2MM 220KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1MOHM,5%,1/4W,AA,TP,2.4X6.4MM 240KOHM,5%,1/4W,AA,TP,2.4X6.4MM 20KOHM,5%,1/4W,AA,TP,2.4X6.4MM 330KOHM,5%,1/2W,AA,TP,3.3X9MM 240Kohm,5%,1/2W,AA,TP,3.9x9mm 1KOHM,5%,1/4W,AA,TP,2.4X6.4MM 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1Mohm,10%,1/2W,AA,TP,3.5x9.5mm 1MOHM,5%,1/4W,AA,TP,2.4X6.4MM 100KOHM,5%,1/2W,AA,TP,2.4X6.4MM 330KOHM,5%,1/2W,AA,TP,2.4X6.4MM Remarks ! ! ! ! ! ! PN17K*/PN17J* 7 Electrical Parts List Loc. No. Code No. Description Specification Remarks R601 R602 R603 R604 R605 R607 R608 R609 R610 R611 R612 R613 R614 R615 R616 R617 R618 R619 R620 R621 R625 R626 R627 R630 R631 R632 SK501 TP501 X201 ZD201 ZD202 ZD203 ZD204 ZD205 ZD206 ZD207 ZD502 ZD503 ZD601 ZD602 ZD604 2001-001129 2001-000023 2001-000290 2001-000857 2001-000734 2003-000014 2001-000281 2002-001068 2002-001068 2001-001079 2003-000738 2001-000290 2001-001107 2001-001088 2001-001108 2001-001037 2001-000429 2003-000471 2001-000354 2001-000989 2001-000786 2001-000044 2004-001022 2001-000786 2001-000429 2001-000290 4715-000001 6042-000002 2801-000005 0403-000361 0403-000361 0403-000361 0403-000361 0403-000361 0403-000361 0403-000361 0403-001068 0403-000355 0403-000361 0403-001068 0403-001274 R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON R-COMPOSITION R-COMPOSITION R-CARBON(S) R-METAL OXIDE(S) R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON SURGE ABSORBER EYELET CRYSTAL-UNIT DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER 330KOHM,5%,1/2W,AA,TP,2.4X6.4MM 47OHM,5%,1/4W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 560OHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10Kohm,5%,3W,AA,TP,6x16mm 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 180Kohm,5%,1/2W,AA,TP,3.9x9mm 180Kohm,5%,1/2W,AA,TP,3.9x9mm 15OHM,5%,1/2W,AA,TP,2.4X6.4MM 56Kohm,5%,2W,AA,TP,4x12mm 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 220ohm,5%,1/2W,AA,TP,2.4x6.4mm 1KOHM,5%,1/2W,AA,TP,2.4X6.4MM 22KOHM,5%,1/2W,AA,TP,2.4X6.4MM 0.39OHM,5%,1/2W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10ohm,5%,2W,AA,TP,4x12mm 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM 820KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4m 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KV,+50-10%,-,-, ID1.5,OD2,L3.1,SN,BSS3-E/EH 8MHz,50ppm,28-AAM,S,35ohm,TP UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ4.7BSA,4.7V,4.47-4.65V,500mW UZ5.1BSB,5.1V,4.97-5.18V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ4.7BSA,4.7V,4.47-4.65V,500mW UZ24BSC,23.29-24.27V,500MW,DO-34,TP HS301 CIS CIS CIS CIS BH99-00002A 1204-001508 6006-001008 6021-000118 BH62-00003A ASSY,HEAT/SINK IC-VERTICAL DEF. SCREW-ASS’Y MACH NUT-HEXAGON HEAT/SINK-V.IC H/S V.IC,SCREW+NUT,KA2142,-,-,OIL SILICON,-,KA2142,SIP,10P,-,PLASTIC,35V,15W,-20TO+70C,ST,VERTICAL DEFLECTION WSP,BH,+,M3,L10,ZPC(YEL),SWRCH 1C,M3,ZPC(YEL),SM20C -,T1,-,A1050S,DA/DB HS601 CIS CIS CIS CIS BH99-00003A BH13-00004A BH61-00004A BH62-00004A BH62-20001B ASSY,HEAT/SINK IC-HYBRID SPRING-TR HEAT/SINK-POWER RUBBER H/S POWER,SPRING,DP104,-,-,RUBBER,-,-,DP104C,TO-220-5L,5P,POWER SWITCH,-,CDA,CDB,SUS304,T0.5,-,-,-,-,T1,-,A1050S,DA/DB CSQ4357,W25*L20*T0.45,-,-,-,- SNA SNA SNA HS401 CIS CIS CIS BH99-00006A 6006-001008 6021-000118 BH62-30024A ASSY,HEAT/SINK SCREW-ASS’Y MACH NUT-HEXAGON HEAT/SINK-TR H/S,SCREW+NUT,IRF630,-,-,OIL SILICON,-,WSP,BH,+,M3,L10,ZPC(YEL),SWRCH 1C,M3,ZPC(YEL),SM20C SPC,T1,SN,CFX1577L SNA SNA SNA SNA HS501 CIS BH99-00009B 0402-001255 ASSY HEAT/SINK DIODE-RECTIFIER HS FBT,SPRING,2SC5440,DTV56F,KTD2058,OIL SILICON,-,DTV56F,1.5KV,10A,TO-220AC,BK SNA PN17K*/PN17J* SNA SNA SNA SNA SNA SNA 7-9 7 Electrical Parts List Loc. No. Code No. Description Specification Remarks CIS CIS CIS CIS CIS 0502-000465 0502-001170 BH61-00004A BH61-70003A BH62-00015A TR-POWER TR-POWER SPRING-TR SPRING HEAT SINK-FBT KTD2058,NPN,25000mW,TO-220IS,ST,100-200 2SC5440,NPN,60000mW,TOP-3E,ST,-8 CDA,CDB,SUS304,T0.5,-,-,-,CVT4857,STS304-W1/2H,T0.5,W3.8 A1050S,T1.0,T1.0,-,- SNA SNA SNA HS402 CIS CIS BH99-00010A BH61-00004A BH62-00016A ASSY,HEAT/SINK SPRING-TR HEAT SINK-TR HS TR,SPRING,IRF634A,-,-,OIL SILICON,-,CDA,CDB,SUS304,T0.5,-,-,-,A1050S,T1.0,-,DP17MO SNA SNA SNA HS409 CIS CIS CIS BH99-10019U 0202-001044 0402-001191 BH62-30024B ASSY HEAT/SINK SOLDER-WIRE. DIODE-RECTIFIER HEAT/SINK-IC HS TR,SOLDER,MUR460,-,-,S63S-W3.0,S63S,D3,63Sn/37Pb,MUR460,600V,4A,CASE267-03,BK SPC-1,T1,SN COATING,- SNA SNA 7-10 SNA PN17K*/PN17J* 7 Electrical Parts List 7-2 Video PCB Parts (PN17K*) Loc. No. C160 CIS CIS CIS CIS CIS CIS CIS CIS CN101 CN102 IC101 JP146 LJP1 S/VID S/VID+H/S SK01 BD102 BD103 C102 C103 C105 C106 C107 C108 C112 C113 C114 C116 C117 C118 C119 C120 C121 C123 C124 C128 C151 C152 CB01 CB02 CB04 CB05 CB06 CB07 CB08 CB09 CG01 CG02 CG04 CG05 CG06 CG07 CG08 CG09 CR01 CR02 CR04 CR05 CR06 CR07 CR08 CR09 D102 Code No. 2401-000039 BH75-00047A BH71-00006B BH71-10311A BH75-00192H BH61-00002A BH71-00007A BH72-00024A BH73-00014A 3711-004228 BH39-00015A 1204-001646 BH39-40305U BH39-40306D 6502-000001 6003-000010 3704-001116 3301-000011 3301-000011 2401-000603 2401-000037 2301-000010 2202-002009 2401-000010 2401-000049 2401-002075 2301-000287 2201-000117 2301-000188 2301-000188 2201-000471 2201-000291 2201-000285 2202-002009 2201-000019 2301-000148 2201-000119 2202-002009 2202-002009 2201-000119 2201-000119 2401-000055 2301-000010 2202-002009 2201-000146 2201-000411 2201-000247 2201-000119 2201-000119 2401-000055 2301-000010 2202-002009 2201-000146 2201-000411 2201-000247 2201-000119 2201-000119 2401-000055 2301-000010 2202-002009 2201-000146 2201-000411 2201-000247 0401-000005 PN17K*/PN17J* Description C-AL UNIT/SHIELD-VIDEO/CAP SHIELD-VIDEO/CAP EARTH-PLATE UNIT/SHIELD-VIDEO SPRING-VIDEO SHIELD-VIDEO HOLDER-VIDEO HOLDER-RUBBER(NORMAL) CONNECTOR-HEADER CBF-HARNESS IC-OSD PROCESSOR CBF HARNESS CBF-HARNESS CABLE CLAMP SCREW-TAPTITE SOCKET-CRT CORE-FERRITE BEAD CORE-FERRITE BEAD C-AL C-AL C-FILM,PEF C-CERAMIC,MLC-AXIAL C-AL C-AL C-AL C-FILM,PEF C-CERAMIC,DISC C-FILM,PEF C-FILM,PEF C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL C-CERAMIC,DISC C-FILM,PEF C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL C-CERAMIC,MLC-AXIAL C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-FILM,PEF C-CERAMIC,MLC-AXIAL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-FILM,PEF C-CERAMIC,MLC-AXIAL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-FILM,PEF C-CERAMIC,MLC-AXIAL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC DIODE-SWITCHING Specification 1000uF,20%,16V,GP,TP,10x16,5 CL17LO,SPTE T0.3,-,-,CL17LO,SPTE,0.2,-,PBS 3/4H,T0.2 DEL,-,SPTE,-,-,14,15,17,CDB7907,STS H14 ,T1.0,-,-,-,NORMAL CDT CDA4507,SPTE,T0.2,-,CDA4507,ABS+PC,5V,IV16,-,NORMAL CRT DEL,SILICON V2,GRAY,-,-,-,NORMAL BOX,6P,1R,2MM,ANGLE,SN 13P/14P,200MM,WHT/BLK/RED/BLU,UL1007,AWG26,SMH200-13/YBNH200-14 S1D2502A09-D0B0,DIP,32P,600MIL,PLASTIC,-,-,-20to75C,ST,52MM,AWG22(0.6PI),-,-,AWG22(0. ,80MM,BLK,1015,AWG22,-,-,-,-,DAWH-5NB,D15,L35,NTR,NYLON66 BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 11P,22.5PI,26.5PI,NI,AA,3.5x1.0x5.7mm,1500,2375G AA,3.5x1.0x5.7mm,1500,2375G 1uF,20%,50V,GP,TP,5x11,5 470uF,20%,16V,GP,TP,8x11.5,5 100nF,5%,100V,TP,11.5x12.5mm,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 220uF,20%,16V,GP,-,6.3x11mm,2. 47uF,20%,100V,WT,TP,10x16,5 4.7uF,20%,50V,GP,TP,5x11,5 5.6nF,5%,100V,TP,10.5x12.5x6.5 1.8nF,10%,500V,Y5P,TP,8.5x3,5 1nF,5%,100V,TP,10.5x12.5x6.5,5 1nF,5%,100V,TP,10.5x12.5x6.5,5 0.33nF,10%,50V,Y5P,TP,4x3.5,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 1nF,10%,1kV,Y5P,TP,8x5,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 10nF,5%,100V,TP,7x3.2x7mm,5mm 100nF,+80-20%,50V,Y5V,TP,8x3,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 100nF,+80-20%,50V,Y5V,TP,2.3X3 100nF,+80-20%,50V,Y5V,TP,8x3,5 100nF,+80-20%,50V,Y5V,TP,8x3,5 1uF,20%,160V,WT,TP,3x11,5mm 100nF,5%,100V,TP,11.5x12.5mm,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 0.1nF,5%,50V,SL,TP,5x3.5,5 0.27nF,10%,50V,Y5P,TP,4x3.5,5 0.015nF,5%,50V,NP0,TP,5x3,5 100nF,+80-20%,50V,Y5V,TP,8x3,5 100nF,+80-20%,50V,Y5V,TP,8x3,5 1uF,20%,160V,WT,TP,3x11,5mm 100nF,5%,100V,TP,11.5x12.5mm,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 0.1nF,5%,50V,SL,TP,5x3.5,5 0.27nF,10%,50V,Y5P,TP,4x3.5,5 0.015nF,5%,50V,NP0,TP,5x3,5 100nF,+80-20%,50V,Y5V,TP,8x3,5 100nF,+80-20%,50V,Y5V,TP,8x3,5 1uF,20%,160V,WT,TP,3x11,5mm 100nF,5%,100V,TP,11.5x12.5mm,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 0.1nF,5%,50V,SL,TP,5x3.5,5 0.27nF,10%,50V,Y5P,TP,4x3.5,5 0.015nF,5%,50V,NP0,TP,5x3,5 1N4148,100V,200mA,DO-35,TP Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA 7-11 7 Electrical Parts List Loc. No. DB01 DB02 DB03 DB04 DB05 DB06 DG01 DG02 DG03 DG04 DG05 DG06 DR01 DR02 DR03 DR04 DR05 DR06 EY1 EY2 EY3 EY4 G2 GND JP103 JP109 JP116 JP117 JP119 JP122 JP123 JP124 JP127 JP128 JP133 JP134 JP136 JP137 JP140 JP142 JP147 JP148 JP150 JP151 JP152 L101 L103 LB01 LG01 LR01 MP1.3 Q102 QB01 QB02 QG01 QG02 QR01 QR02 R101 R102 R103 R104 R107 7-12 Code No. Description 0401-000005 0401-000005 0401-000004 0401-000004 0401-000005 0401-000005 0401-000005 0401-000005 0401-000004 0401-000004 0401-000005 0401-000005 0401-000005 0401-000005 0401-000004 0401-000004 0401-000005 0401-000005 6042-000002 6042-000001 6042-000001 6042-000002 BH71-40300A BH71-40300A BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U 2701-000112 2701-000164 2701-000172 2701-000172 2701-000172 BH41-00058A 0501-000122 0501-000140 0501-000138 0501-000140 0501-000138 0501-000140 0501-000138 2001-000522 2001-000281 2001-001138 2001-001138 2001-000429 DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING EYELET EYELET EYELET EYELET PIN-HINGE PIN-HINGE CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS INDUCTOR-AXIAL INDUCTOR-AXIAL INDUCTOR-AXIAL INDUCTOR-AXIAL INDUCTOR-AXIAL PCB-VIDEO TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL R-CARBON R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON Specification 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1SS244,250V,625mA,DO-34,TP 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1SS244,250V,625mA,DO-34,TP 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1SS244,250V,625mA,DO-34,TP 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP ID1.5,OD2,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH -,BRASS,D2.36,SN,HEAT/SINK -,BRASS,D2.36,SN,HEAT/SINK 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 100uH,10%,3x7mm 27uH,10%,4.2x9.8mm 330nH,10%,3x7mm 330nH,10%,3x7mm 330nH,10%,3x7mm TP17LT,PHENOL,-,1.6T*247*330MM,2N3904,NPN,625mW,TO-92,TP,100-300 2N5551,NPN,625mW,TO-92,TP,80-250 2N5401,PNP,625mW,TO-92,TP,60-240 2N5551,NPN,625mW,TO-92,TP,80-250 2N5401,PNP,625mW,TO-92,TP,60-240 2N5551,NPN,625mW,TO-92,TP,80-250 2N5401,PNP,625mW,TO-92,TP,60-240 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 390OHM,5%,1/2W,AA,TP,2.4X6.4MM 390OHM,5%,1/2W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA PN17K*/PN17J* 7 Electrical Parts List Loc. No. Code No. Description R108 R109 R114 R115 R116 R117 R118 R119 R120 R123 R124 RB01 RB02 RB03 RB04 RB08 RB09 RB10 RB11 RB12 RB13 RB14 RB15 RB20 RG01 RG02 RG03 RG04 RG08 RG09 RG10 RG11 RG12 RG13 RG14 RG15 RG20 RR01 RR02 RR03 RR04 RR08 RR09 RR10 RR11 RR12 RR13 RR14 RR15 RR20 SK101 SK102 SKB01 SKG01 SKR01 2001-000812 2001-000563 2001-000780 2001-000577 2001-000290 2001-000734 2001-000857 2001-000857 2002-001022 2001-000432 2001-000034 2001-000969 2001-000969 2001-000780 2001-000281 2001-000793 2001-000962 2001-000705 2001-000281 2001-000449 2001-001000 2001-000780 2001-000793 2001-000947 2001-000969 2001-000969 2001-000780 2001-000281 2001-000793 2001-000962 2001-000705 2001-000281 2001-000449 2001-001000 2001-000221 2001-000793 2001-000947 2001-000969 2001-000969 2001-000780 2001-000281 2001-000793 2001-000962 2001-000705 2001-000281 2001-000449 2001-001000 2001-000780 2001-000793 2001-000947 1405-001064 4715-000001 4715-000102 4715-000102 4715-000102 R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-COMPOSITION R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON SURGE ABSORBER SURGE ABSORBER SURGE ABSORBER SURGE ABSORBER SURGE ABSORBER 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM 470OHM,5%,1/8W,AA,TP,1.8X3.2MM 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 560OHM,5%,1/8W,AA,TP,1.8X3.2MM 560OHM,5%,1/8W,AA,TP,1.8X3.2MM 30MOHM,5%,1/4W,AA,TP,2.5X6.5MM 1MOHM,5%,1/4W,AA,TP,2.4X6.4MM 220OHM,5%,1/4W,AA,TP,2.4X6.4MM 75OHM,5%,1/8W,AA,TP,1.8X3.2MM 75OHM,5%,1/8W,AA,TP,1.8X3.2MM 470OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 47OHM,5%,1/8W,AA,TP,1.8X3.2MM 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM 39OHM,5%,1/2W,AA,TP,3.3X9MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 82KOHM,5%,1/8W,AA,TP,1.8X3.2MM 470OHM,5%,1/8W,AA,TP,1.8X3.2MM 47OHM,5%,1/8W,AA,TP,1.8X3.2MM 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 75OHM,5%,1/8W,AA,TP,1.8X3.2MM 75OHM,5%,1/8W,AA,TP,1.8X3.2MM 470OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 47OHM,5%,1/8W,AA,TP,1.8X3.2MM 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM 39OHM,5%,1/2W,AA,TP,3.3X9MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 82KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47OHM,5%,1/8W,AA,TP,1.8X3.2MM 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 75OHM,5%,1/8W,AA,TP,1.8X3.2MM 75OHM,5%,1/8W,AA,TP,1.8X3.2MM 470OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 47OHM,5%,1/8W,AA,TP,1.8X3.2MM 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM 39OHM,5%,1/2W,AA,TP,3.3X9MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 82KOHM,5%,1/8W,AA,TP,1.8X3.2MM 470OHM,5%,1/8W,AA,TP,1.8X3.2MM 47OHM,5%,1/8W,AA,TP,1.8X3.2MM 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 400V,20%,-,-,AXIAL 1KV,+50-10%,-,-, 200V,20%,1000A,-,RADIAL 200V,20%,1000A,-,RADIAL 200V,20%,1000A,-,RADIAL HS103 CIS CIS CIS CIS BH99-00004B 6006-001008 6021-000118 BH13-00003A BH62-00006A ASSY,HEAT/SINK SCREW-ASS’Y MACH NUT-HEXAGON IC-HYBRID HEAT SINK-VIDEO H/S VIDEO,SCREW+NUT,LM2437,-,-,OIL SILICON,-,WSP,BH,+,M3,L10,ZPC(YEL),SWRCH 1C,M3,ZPC(YEL),SM20C -,LM2437,TO-220,9P,CRT DRIVER,0 TO 6.0V,-,A1050S T2.0,-,DB PN17K*/PN17J* Specification Remarks SNA SNA SNA SNA SNA SNA SNA 7-13 7 Electrical Parts List 7-3 Others Loc. No. Code No. CRT ASS`Y PBA UNIT B/C ASS`Y CODE (PN17K*) (PN17J*) (PN17K*) (PN17K*) (PN17J*) (PN17J*) S/CABLE DEGAUSSING MAGNET BH03-00024D BH94-00210A BH94-00228A BH98-00193A BH98-00194A BH98-00207A BH98-00208A BH39-00145A BH27-00047A BH27-00054A 3302-000006 Description CRT-SF ASSY PCB ASSY PCB-SC ASSY PCB/MAIN ASSY PCB/VIDEO ASSY PCB/MAIN-SC ASSY PCB/VIDEO-SC CBF SIGNAL COIL-DEGAUSSING COIL DEGAUSSING-ASS’Y MAGNET-RUBBER Specification Remarks M41QCJ761X172(P/5),96,17,0.25,-,29.1,FST,H/C,NH,-,FILM,TILT,4 PN17KT-07C1/4343,-,-,PN17KT,-,-,PN17KT-07C1/4343,-,-,PN17KT-07C1/4343,-,-,PN17JT,-,-,PN17JT,-,-,ATT,1500MM,15P/6P,7P,IVORY(IV01),-,D-SUB/MALE 320*250*1100mm,9.6mH,-,100Ts,°æ10% 320*250*1100mm,9.6mH,-,100Ts,°æ10% AF,14G,1620-1980G,0.58-0.9MGOe SNA SNA SNA SNA SNA SNA SNA SNA 7-4 Different Part List (PN17JT/JO) MAIN Loc.No 85KHZ R219 R455 R456 R457 R526 R527 ZD206 ZD207 C431 C437 C441 C442 C443 C444 HS403 JP66 JP71 JP72 D406 D430 Q420 Q421 7-14 Code-No BH39-40305U 2001-000290 2001-000449 2001-000290 2001-000786 2001-000766 2001-000786 2301-001259 2301-001259 2401-000603 2301-001249 2303-000122 2303-000122 BH99-00005G BH39-40305U 0402-001313 0402-000006 0501-000586 0505-001309 VIDEO Specification CBF HARNESS;52MM,AWG22(0.6PI),-,-,AWG22(0. R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;43KOHM,5%,1/8W R-CARBON;47KOHM,5%,1/8W C-FILM,MPPF;100nF,5%,400V,TP,19x8x16,7.5mm C-FILM,MPPF;100nF,5%,400V,TP,19x8x16,7.5mm C-AL;1uF,20%,50V,GP,TP,5x11,5 C-FILM,MPPF;68nF,5%,400V,TP,19x7x15mm,7.5 C-FILM,PPF;10nF,5%,630V,TP,19x12.5mm,7.5m C-FILM,PPF;10nF,5%,630V,TP,19x12.5mm,7.5m ASSY,HEAT/SINK;HSTR,SPRING,IRF740A,-,-,O CBF HARNESS;52MM,AWG22(0.6PI),-,-,AWG22(0. Loc.No Code-No HS103 LB01 LG01 LR01 RB08 RB13 RB14 RG08 RG13 RR08 RR13 RR14 A+A1 B+B1 C+C1 C119 BOTTOM BH99-00004C 2701-001063 2701-001063 2701-001063 2001-000019 2001-000273 2001-000025 2001-000019 2001-000273 2001-000019 2001-000273 2001-000025 BH39-40306C BH39-40306C BH39-40306C BH39-40361A Specification ASSY,HEAT/SINK;HS VIDEO,SCREW+NUT,LM2435,-,INDUCTOR-AXIAL;150nH,10%,3x7mm INDUCTOR-AXIAL;150nH,10%,3x7mm INDUCTOR-AXIAL;150nH,10%,3x7mm R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/4W,AA,TP,2.4X6.4MM R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/4W,AA,TP,2.4X6.4MM CBF-HARNESS;,60MM,BLK,1015,AWG22,-,-,-,-,CBF-HARNESS;,60MM,BLK,1015,AWG22,-,-,-,-,CBF-HARNESS;,60MM,BLK,1015,AWG22,-,-,-,-,CBF-HARNESS;-,40MM,BLK,UL 1015,AWG22,- DIODE-RECTIFIER;ERD07-15AL,1.7VK,1.5A,-,BK DIODE-RECTIFIER;1N4007GP,1000V,1A,DO-41,TP TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,TP,12 FET-SILICON;IRF630,N,200V,10A,0.4OHM,100W,TO PN17K*/PN17J* PN17K*/PN17J* AC INPUT SOCKET CN601 ON THE CRT TO D-COIL LINE FILTER L601 DEGAUSSING BLOCK RL601 24LC04 EPROM IC202 MCU IC201 H/V SYNC VIDEO INPUT FRONT CONTROL BOARD LED POWER UP, DOWN BRIGHTNISS CONTRASTER PIN, TRAP SIZE, POSI, DEGA. SIGNAL RETIFIER BRIDGE POWER PWM CONTROL IC601C TILT V-MUTE S-CORRECTION REF- OFF BB HOR. LINEARITY REG. 12C DATA 12C CLK H-SYNC1 V-SYNC1 E/W_OUT H-SYNC, V-SYNC MAIN BOARD SWITCHING TRANS T601 KSC945 VER. BLANKING Q303 HOR./VER. PROCESSOR IC401 TDA4859 VIDEO PRE-AMP + OSD IC101(KA2506) IC104(KA2501) VIDEO BOARD +12V HOR. OUT Q404 HEATER VOLTAGE CONTROL +6.3V Heater Switching Q610 VER.OUT & TILT CONTORL +12V REGULATOR TO VIDEO S-COR. KSC5802 H. D. T T401 VER. DY CN401 SOCKET -12V +13V +56V +70V FROM MCU HOR. DRIVE Q403 VER. OUTPUT IC301 KA2142 HEATER G1 RGB - CUTOFF QR, G,B01,02 VIDEO OUTPUT IC103(LM2437) REF-OFF(From MCU) CRT HEATER BB(From MCU) G1 DYNAMIC FOCUS T502 HOR. DY CN401 VERTICAL FOCUS FROM IC401 H/V SIZE REG. RGB ACL CIRCUIT B(+) FBT T501 S C R E E N -210V (FROM FBT) BRIGHTNESS CONTROL CONTRAST CONTROL F O C U S CONTROL BRIGHTNESS CONTROL CONTRAST +12V +30V -210V H/V 8 Block Diagrams 8-1 8 Block Diagrams Memo 8-2 PN17K*/PN17J* 9 Wiring Diagram MAIN PCB CRT SOCKET PCB CRT SOCKET FOCUS1 (WHT) FOCUS2 (RED) G2 2 x 3p DY 15"/17" H+ (RED) H+ NC (BLUE) H(YEL) V+ H– NC (BROWN)V- 1 1 2 3 4 2 3 4 (YEL)V+ 1 NC 2 (Brown)V – 3 1 2 3 2 x 3p DY 15"/17" H + H + CN401 H– NC CN402 V + H– CN302 V– NC CN303 1 2 V + NC V– CN301 1 1 2 2 AC INPUT AC AC 1 AC INPUT 2 NC 3 AC INPUT V+ V– GT601 GT602 FOCUS (WHT) CN102 CN201 70 V GND 6.3 V G1 GND 12 V V-SYNC ACL IICDATA IICCLK CLAMP 5V AFC DEGAUSSING COIL AC AC CN501 FBT 1 1 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 9 10 11 12 13 10 11 12 13 14 CN601 70 V GND 6.3 V BLANK G1 GND 12 V V-SYNC ACL IICDATA IICCLK CLAMP 5V AFC CN203 1 KEY 1 GND SW201 SW202 SW203 SW204 2 CN202 CN101 1 SIGNAL CABLE 1 GND H-IN V-IN DDC DATA DDC CLK S-RASTER DDC 5V 1 R_IN 2 GND_R 3 G_IN 4 GND_G 5 B_IN 6 GND_B 1 2 3 4 2 3 4 5 6 2 3 4 5 6 7 1 TILT+(WHT) 2 NC TILT–(BLK) 3 5 6 7 TILT + 1 NC 2 TILT – 3 TILT R GND G GND B GND GND H-IN V-IN DDC DATA DDC CLK S-RASTER DDC 5V CN304 15 PIN D-SUB refer to pin assignment of product spec. PN17K*/PN17J* 9-1 9 Wiring Diagrams Memo 9-2 PN17K*/PN17J* 10 Schematic Diagrams 10-1 Main Part Schematic Diagram 9 23 GT501 R516 D516 R531 V_REG_1 3 12 IC201 R526 T501 R527 R532 R507 C404 REG D515 R530 CN501 R505 S4 18 11 R458 R410 L402 D431 4 C410 Q423 REG R239 C408 Q402 C445 C447 R212 10 C406 R211 T502 C225 V_REG_1 R455 7 8 14 C448 13 C446 L403 Q420 S4 R456 R419 C442 D430 R420 C425 C430 C427 Q421 C417 C412 Q407 R459 L401 R443 C441 R457 C411 C435 D612 C443 HS403 C624 D407 BD401 BD402 C604 C444 Q422 Q608 C420 C421 C436 BD403 C419 D408 C621 C603 C613 R428 R425 D406 R431 Q404 D422 R444 D405 R432 D617 1 2 Q403 6 R427 5 PN17K*/PN17J* 10-1 10 Schematic Diagrams 1 100 V (IC601, #1) 2 100V (IC601, #1) 3 2.00 V (IC401, #6) 4 1.00V (IC401, #8) 5 20.0 V (Q403, Collector) CH1 P-P = 100 V CH1 P-P = 100V CH1 P-P = 2.00V CH1 P-P = 2.00V CH1 P-P = 20.0 V CH1 RMS = 350.2 V CH1 RMS = 325.8 V CH1 RMS = 5.868V CH1 RMS = 5.868V CH1 RMS = 46.80V 6 200 V (Q408, Collector) 7 1.00 V (IC401, #11) 8 500 V (IC401, #12) 9 10.0 V (IC301, #6) 10 2.00 V (Q402, Gate) CH1 P-P = 200V CH1 P-P = 1.00V CH1 P-P = 500 V CH1 P-P = 10.0 V CH1 P-P = 2.00 V CH1 RMS = 387.2V CH1 RMS = 3.008 V CH1 RMS = 1.425 V CH1 RMS = 5.06 V CH1 RMS = 7.692V 11 50.0 V (Q402, Drain) 12 2.00 V (IC401, #32) 13 50.0 V (T502, #6) 14 100 V (T502, #1) 18 1.00 V (IC201, #13, 14) CH1 P-P = 50.0 V CH1 P-P = 2.00V CH1 P-P = 50.0V CH1 P-P = 100V CH1 P-P = 1.00 V CH1 RMS = 73.7V CH1 RMS = 6.124V CH1 RMS = 75.6V CH1 RMS = 124.0V CH1 RMS = 2.108V 23 5.00V (Q303, Collector) CH1 P-P = 5.00V 10-2 CH1 RMS = 28.33V PN17K*/PN17J* 10 Schematic Diagrams 10-2 Video Part Schematic Diagram 19 20 24 16 21 22 15 17 PN17K*/PN17J* 10-3 10 Schematic Diagrams 15 1.00V (IC101 #5, 6, 7) 16 1.00V (IC101 #18,19,20) 17 20.0V (IC103, #1, 2, 3) 19 1.00 V (IC104, #6) 20 1.00 V (IC104, #8) CH1 P-P = 1.00V CH1 P-P = 1.00V CH1 P-P = 20.0V CH1 P-P = 1.00V CH1 P-P = 1.00V CH1 RMS = 2.452V CH1 RMS = 2.792V CH1 RMS = 40.52V 21 1.00 V (IC101, #18,19,20) 22 10.0 V (R,G,B, Video) 24 20.00V (CRT Socket, G1) CH1 P-P = 1.00V CH1 P-P = 10.0V CH1 P-P = 20.0V 10-4 CH1 RMS = 2.580V CH1 RMS = 17.02V CH1 RMS = 4.516V CH1 RMS = 5.024V CH1 RMS = 66.68V PN17K*/PN17J*