Download Bunn IC3 Operating instructions

Transcript
COFFEE BREWING
1. Begin each brew cycle with a clean empty brew funnel and dispenser. (Be sure the dispenser lid doesn’t
interfere with the flow of dilution water.)
2. Insert a BUNN® 3-gallon urn filter into the funnel.
3. Pour the recommended amount of fresh coffee into the filter.
4. Level the bed of coffee grounds by gently shaking.
5. Slide the funnel into the funnel rails until it stops.
6. Place the On/Off switch in the lighted “ON” position.
7. Place the batch selector switch in the desired position.
8. Momentarily press the start switch.
CAUTION - The funnel contains hot liquids. Remove funnel slowly.
9. Carefully remove the funnel and discard the used filter when coffee no longer drips from the funnel.
10. Place the lighted On/Off switch in the “OFF” position to prevent a false start.
11. Room temperature fresh coffee is available at the faucet.
REPLACEMENT PARTS
03772.0001 ....
05920.0000 ....
00603.0000 ....
03024.0005 ....
03409.0000 ....
03408.0000 ....
24447.0000 ....
03717.0000 ....
03773.0000 ....
24613.0001 ....
22397.0001 ....
00459.0000 ....
00400.0001 ....
00412.0001 ....
00432.0001 ....
24599.0001 ....
24614.0001 ....
20528.1330 ....
01155.0000 ....
01154.0001 ....
20526.1330 ....
24600.0000 ....
12485.0003 ....
24659.0000 ....
12499.0002 ....
24657.0000 ....
12305.1000 ....
12322.1000 ....
00668.0000 ....
12422.0000 ....
23717.0001 ....
03170.0000 ....
00484.0002 ....
12984.0004 ....
10966.0000 ....
01592.0000 ....
Base Guide
Cable Clamp .25”
Cable Clamp .437”
Control Thermostat
Decal, Caution, Hot Liquid
Decal, Caution, Remove Funnel Slowly
Decal, Hood Front
Dilution Nozzle
Dilution Nozzle Spacer Housing
Fitting, .25” Flare x .128” MPT Adapter
Fitting, .25” Hose Barb x .125” MPT
Fitting, Bulkhead, .25” Male Flare
Fitting, Elbow, .25” Male Flare x .125” MPT
Fitting, Hex Nipple, .125” MPT
Fitting, Street Elbow, .125” NPT
Fitting, Tee Union, .125” FPT
Fitting, Union, .25” Female Flare
Flow Control Assy, .33 gpm
Flow Control Gasket
Flow Control Outlet
Flow Control Washer, .33 gpm
Foot Replacement Kit
Funnel Handle
Funnel Handle Mounting Bracket
Funnel Handle Screw
Funnel, Assy, Complete
Heater Kit, 4000W/208V or 3700W/200V
Heater Kit, 4000W/240V
Hole Plug, .75” Dia
Hose Clamp .5”
Limit Thermostat
Mounting
Needle Valve
Ready Indicator Assy, Green
Shipping Carton Complete
Snap Bushing 1” Dia
01079.0000 ....
01101.0000 ....
21181.0000 ....
01111.0000 ....
01085.0002 ....
21180.0000 ....
24527.0000 ....
05515.0000 ....
24697.0000 ....
02753.0000 ....
02754.0000 ....
02628.0000 ....
05789.0000 ....
24612.0000 ....
24410.0000 ....
12377.0000 ....
07038.0000 ....
01106.0001 ....
32400.0002 ....
32400.0001 ....
24435.0000 ....
24427.0000 ....
24698.0000 ....
00310.0005 ....
24569.0000 ....
24531.0000 ....
24532.0000 ....
00310.0000 ....
11707.1001 ....
22249.0000 ....
23721.0000 ....
23820.1000 ....
02240.0002 ....
21014.0055 ....
24533.0000 ....
24533.0001 ....
Page 6
Solenoid Valve Base
Solenoid Valve Coil, (IC3)
Solenoid Valve Coil, (IC3B)
Solenoid Valve Repair Kit
Solenoid Valve, (IC3)
Solenoid Valve, (IC3B)
Sprayhead Assy
Sprayhead Tube Gasket
Sprayhead Tube Kit
Switch, Lighted On/Off, (IC3)
Switch, Lighted On/Off, (IC3B)
Switch, Momentary Start
Switch, Rocker, Batch Selector
Tank
Tank Lid
Tank Lid Gasket
Terminal Block, (IC3)
Terminal Block, (IC3B)
Timer kit, Digital (120V) (IC3)
Timer, kit, Digital (240V) (IC3B)
Top Lid
Trunk Extension Rear Panel
Trunk Rear Panel
Tube Assy, Bulkhead Fitting to Solenoid
Tube Assy, Flow Control To Tank
Tube Assy, Tank Fill
Tube Assy, Vent
Tube Assy, Water Strainer to Bulkhead Fitting
Tube, Silicone-.25” ID x 36"
Water Strainer End Cap .25” Flare
Water Strainer Replacement Screen
Water strainer Assy., Complete
Wire Assy, 1/2 Batch Switch to Timer
Wire Assy, Limit Thermostat to Tank Heater
Wiring Harness, Main (IC3)
Wiring Harness, Main (IC3B)
10792 071503