Download Sharp XL-3000V Service manual
Transcript
XL-3000V SERVICE MANUAL No. S8149XL3000V/ VIDEO CD COMPACT AUDIO SYSTEM MODEL XL-3000V XL-3000V Video CD Compact Audio System consisting of XL3000V (main unit) and CP-XL3000U (speaker system). • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified should be used. NTSC/PAL CONTENTS Page SAFETY PRECAUTION FOR SERVICE MANUAL .......................................................................................................... 2 VOLTAGE SELECTION .................................................................................................................................................... 2 AC POWER CORD AND PLUG ADAPTOR ..................................................................................................................... 2 SPECIFICATIONS ............................................................................................................................................................ 3 NAMES OF PARTS .......................................................................................................................................................... 4 OPERATION MANUAL ..................................................................................................................................................... 6 DISASSEMBLY ............................................................................................................................................................... 10 REMOVING AND REINSTALLING THE MAIN PARTS .................................................................................................. 12 ADJUSTMENT ................................................................................................................................................................ 13 TEST MODE ................................................................................................................................................................... 16 NOTES ON SCHEMATIC DIAGRAM ............................................................................................................................. 19 TYPES OF TRANSISTOR AND LED .............................................................................................................................. 19 BLOCK DIAGRAM .......................................................................................................................................................... 20 SCHEMATIC DIAGRAM ................................................................................................................................................. 26 WIRING SIDE OF P.W.BOARD ...................................................................................................................................... 36 WAVEFORMS OF CD CIRCUIT ..................................................................................................................................... 41 TROUBLESHOOTING .................................................................................................................................................... 42 FUNCTION TABLE OF IC .............................................................................................................................................. 48 LCD DISPLAY ................................................................................................................................................................. 62 PARTS GUIDE/EXPLODED VIEW SHARP CORPORATION –1– This document has been published to be used for after sales service only. The contents are subject to change without notice. XL-3000V SAFETY PRECAUTION FOR SERVICE MANUAL This product is classified as a CLASS 1 LASER PRODUCT. Precaution to be taken when replacing and servicing the Laser Pickup. The AEL (Accessible Emission Level) of Laser Power Output is less than Class 1 but the laser component is capable of emitting radiation exceeding the limit for Class1. Therefore it is important that the following precautions must be observed during servicing to protect your eyes against exposure to the Laser beam. (1) When the cabinet has been removed, the power is turned on without a compact disc, and the Pickup is on a position outer than the lead-in position, the Laser will light for several seconds to detect a disc. Do not look into the Pickup Lens. (2) The Laser Power Output of the Pickup inside the unit and replacement service parts have already been adjusted prior to shipping. (3) No adjustment to the Laser Power should be attempted when replacing or servicing the Pickup. (4) Under no circumstances look directly into the Pickup Lens at any time. (5) CAUTION - Use of controls or adjustments, or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0.6 mW ● This Video CD Compact Audio System is classified as a CLASS 1 LASER product. ● The CLASS 1 LASER PRODUCT label is located on the rear cover. ● Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. CAUTION-INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. ADVERSEL-USYNLIG LASERSTRALING VED ABNING. SE IKKE IND I STRALEN-HELLER IKKE MED OPTISKE INSTRUMENTER. VARO! AVATTAESSA OLET ALTTIINA NAKYMATON LASERSATEILYLLE. ALA TUIJOTA SATEESEEN ALAKA KATSO SITA OPTISEN LAITTEEN LAPI. VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD. STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN GENOM OPTISKT INSTRUMENT. VOLTAGE SELECTION Before operating the unit on mains, check the preset voltage. If the voltage is different from your local voltage, adjust the voltage as follows, Turn the selector with a screwdriver unit the appropriate voltage number appears in the window (110 V,127 V, 220 V or 230 V - 240 V AC). AC POWER CORD AND PLUG ADAPTOR QACCE0001SJZZ QPLGA0250AFZZ QACCA0001SJ00 QPLGA0253AFZZ QACCB0001SJ00 –2– XL-3000V FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. SPECIFICATIONS ■ General ■ CD player Power source AC 110/127/220/230 - 240 V, 50/60 Hz Type Compact disc player Power consumption 56 W Signal readout Non-contact, 3-beam semiconductor laser pickup Dimensions Width: 230 mm (9-1/16") Height: 128 mm (5-1/16") Depth: 293 mm (11-9/16") D/A converter 1-bit D/A converter 3.3 kg (7.3 lbs.) Frequency response 20 - 20,000 Hz Weight Dynamic range 90 dB (1 kHz) ■ Amplifier Output power MPO: 60 W (30 W + 30 W) (10 % T.H.D.) RMS: 40 W (20 W + 20 W) (10 % T.H.D.) Output terminals CD digital output (optical) Video out: 1 Vp-p (75 ohms) PAL/NTSC FM: 88 - 108 MHz AM: 531 - 1,602 kHz ■ Speaker Type 2-way type speaker system 5 cm (2") Tweeter Video/Auxiliary (audio signal): 500 mV/47 kohms ■ Video CD Video output format Frequency range Speakers: 6 ohms Headphones: 16 - 50 ohms (recommended: 32 ohms) Input terminals ■ Tuner 10 cm (4") Woofer Maximum input power 40 W Rated input power 20 W Impedance 6 ohms Dimensions Width: 140 mm (5-9/16") Height: 288 mm (11-3/8") Depth: 187 mm (7-3/8") Weight 2.3 kg (5.1 lbs.)/each Specifications for this model are subject to change without prior notice. –3– XL-3000V NAMES OF PARTS ■ Front panel 7 1. Disc Compartment 2. Volume Up and Down Buttons 3. On/Stand-by Button 4. Function Selector Button 5. Memory/Set Button 6. Bass/Treble Selector Button 7. Video CD/CD Play or Pause, Tuning Up Button 8. Video CD Stop or Return, CD Stop, Tuning Down Button 9. Video CD Skip or Previous, CD Track Down, Tuner Preset Down Button 10. Disc Compartment Cover Open/Close Button 11. Video CD Skip or Next, CD Track Up, Tuner Preset Up Button 10 8 1 11 9 2 3 5 4 1 ■ Display 1. Timer Play Indicator 2. Sleep Indicator 3. Video CD/CD Random Play Indicator 4. Memory Indicator 5. FM Stereo Mode Indicator 6. Video CD/CD Play Indicator 7. Video CD/CD Repeat Play Indicator 8. FM Stereo Receiving Indicator 9. Surround Indicator 6 2 4 3 5 8 6 9 7 ■ Rear panel 1 6 7 2 8 3 9 10 4 11 5 1. CD Digital Output Socket 2. AM Aerial Terminal 3. Aerial Earth Terminal 4. FM 75 Ohms Aerial Socket 5. Headphone Socket 6. Video Output Socket 7. Cooling Fan 8. Video/Auxiliary (Audio Signal) Input Sockets 9. AC Voltage Selector 10. AC Power Input Socket 11. Speaker Terminals The rating label is located on the bottom of the unit. ■ Speaker system 1. Tweeter 2. Woofer 3. Bass Reflex Duct 4. Speaker Terminals 1 2 3 4 –4– XL-3000V ■ Remote control 1 2 3 4 5 6 7 8 11 12 13 14 15 16 17 19 20 23 21 24 22 25 26 27 18 9 10 28 32 29 33 30 34 31 35 Buttons with " " mark in the illustration can be operated on the remote control only. Other buttons can be operated both on the main unit and the remote control. –5– 1. Remote Control Transmitter 2. On/Stand-by Button 3. Video CD/CD Button 4. Tuner Button 5. Timer Button 6. Clock Button 7. Memory Button 8. Dimmer Button 9. Surround Button 10. Volume Up and Down Buttons 11. Video/Auxiliary Button 12. Video CD TV Type Button 13. Band Selector Button 14. Video CD/CD Clear Button 15. Sleep Button 16. Random/Repeat Button 17. Disc Compartment Cover Open/Close Button 18. Audio Mode Button 19. Tuner Preset Up Button 20. Video CD Skip or Previous, CD Track Down Button 21. Video CD/CD Fast Reverse, Tuning Down Button 22. Video CD/CD Play Button 23. Video CD Skip or Next, CD Track Up Button 24. Video CD/CD Fast Forward, Tuning Up Button 25. Video CD/CD Pause Button 26. Video CD Stop or Return, CD Stop Button 27. Tuner Preset Down Button 28. Bass Up and Down Buttons 29. Video CD/CD Direct Search Buttons 30. Video CD Intro Button 31. Video CD Track Digest Button 32. Treble Up and Down Buttons 33. Video CD Playback Control Auto/Off Button 34. Video CD/CD Display Button 35. Video CD Time Search Button XL-3000V OPERATION MANUAL Setting the Clock 3 Within 1 minute, press the PRESET ( or ) button to adjust the hour and then press the MEMORY button. When the 12-hour display is selected, "AM" will change automatically to "PM". 4 This may be operated only with the remote control. In this example, the clock is set for the 24-hour (0:00) display. 1 Press the CLOCK button and within 3 seconds, press the MEMORY button. Within 1 minute, press the PRESET ( or ) button to adjust the minutes and then press the MEMORY button. ● The hour will not advance even if minutes advance from "59" to "00". ● The clock starts from "0" second. (Seconds are not displayed.) 2 Within 1 minute, press the PRESET ( or ) button to select 24-hour or 12-hour display and then press the MEMORY button. To confirm the time display when the power is on: Press the CLOCK button. The time display will appear for about 5 seconds. "0:00" The 24-hour display will appear. (0:00 - 23:59) Note: The time will flash at the push of the CLOCK button when the AC power supply is restored after a power failure or unplugging the unit. Readjust the clock as follows. "AM 12:00" The 12-hour display will appear. (AM 12:00 - PM 11:59) Note that this can only be set when the unit is first installed or it has been reset. To readjust the clock: Perform "Setting the Clock" from the beginning. To change the 24-hour or 12-hour display: 1 Clear all the programmed contents. 2 Perform "Setting the Clock" from the beginning. Remote Control Troubleshooting ■ Battery installation ■ If trouble occurs 1 2 When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction. 3 Remove the battery cover. Insert the batteries according to the direction indicated in the battery compartment. When inserting or removing the batteries, push them towards the battery terminals. Replace the cover. If such a problem occurs, do the following: 1 Set the unit to the stand-by mode and turn the power on again. 2 If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on. Note: If neither operation above restores the unit, clear all the memory by resetting it. ■ Clearing all the memory (reset) Precautions for battery use: ● Replace all old batteries with new ones at the same time. ● Do not mix old and new batteries. ● Remove the batteries if the unit will not be used for long periods of time. This will prevent potential damage due to battery leakage. 1 2 3 Caution: ● Do not use rechargeable batteries (nickel-cadmium battery, etc.). ● Installing the batteries incorrectly may cause the unit to malfunction. Notes concerning use: ● Replace the batteries if the operating distance is reduced or if the operation becomes erratic. Purchase 2 "AAA" size batteries (UM4, R03, HP-16 or similar). ● Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth. ● Exposing the sensor on the unit to strong light may interfere with operation. Change the lighting or the direction of the unit. ● Keep the remote control away from moisture, heat, shock, and vibrations. Press the ON/STAND-BY button to enter the power stand-by mode. Unplug the AC power lead from the AC INPUT socket on the unit. Whilst pressing down the MEMORY/SET button and the button, plug the AC power lead into the AC INPUT socket on the unit. AC INPUT Caution: ● This operation will erase all data stored in memory including clock, timer settings, tuner preset, and CD programme. ● After the above operation, interval span setting for AM will be returned to 9 kHz (50 kHz for FM) automatically. –6– XL-3000V System Connections FM aerial AM loop aerial Right speaker MD recorder Left speaker not supplied TV Right speaker Left speaker To a wall socket Black wire with white dots Black wire System Connections (continued) ■ Placing the speaker system ■ TV/monitor connection There is no distinction between the right and the left speakers. If the TV/monitor has a video input, connect it to VIDEO OUT socket on the rear of the unit. Left speaker Right speaker TV To video input socket Speaker grilles are removable: Make sure nothing comes into contact with the speaker diaphragms when you remove the speaker grilles. Video cable Notes: ● The speakers are magnetically shielded. Therefore, they do not affect the display even you use them near the TV. However, some colour variation may occur, depending on the type of TV used. If colour variation occurs... Turn off the TV (from the power switch). After 15 - 30 minutes, turn the TV on again. If the colour variation is still present... Move the speakers further away from the TV. ● If any kind of magnet or an electromagnet is placed too close to the TV and the system, irregular colours may appear on the TV screen. Note: If the TV/monitor does not have a video input, the VIDEO OUT socket on the unit should be connected to a VCR with a video input, which in turn should be connected to the TV/monitor through the TV ANTENNA/CABLE input. (Be sure to turn on the VCR, and set the VCR's input mode to "auxiliary".) –7– XL-3000V System Connections (continued) ■ Setting the AC voltage selector ■ Connecting the AC power lead Check the setting of the AC voltage selector located on the rear panel before plugging the unit into a wall socket. If necessary, adjust the selector to correspond to the AC power voltage used in your area. After checking all the connections have been made correctly, connect the AC power lead to the AC power input socket, then into the wall socket. Wall socket Turn the selector with a screwdriver until the appropriate voltage number appears in the window (110 V, 127 V, 220 V or 230 V - 240 V AC). 1 2 Notes: ● Unplug the AC power lead from the wall socket if the unit will not be in use for a prolonged period of time. ● Never use a power lead other than the one supplied. Use of a power lead other than the one supplied may cause an electric shock or fire. AC Plug Adaptor In areas (or countries) where a wall socket as shown in illustration is used, connect the unit using the AC plug adaptor supplied with the unit, as illustrated. The AC plug adaptor is not included in areas where the wall socket and AC power plug can be directly connected (see illustration ). System Connections (continued) ■ Setting the AM/FM interval The International Telecommunication Union (ITU) has established that member countries should maintain either a 10 kHz or 9 kHz interval between broadcasting frequencies of AM stations and 100 kHz or 50 kHz for FM stations. The illustration shows the 50/9 kHz zones (regions 1 and 3), and the 100/10 kHz zone (region 2). This product is not equipped with a span selector. However, it will be adjusted to a 9 kHz AM (50 kHz FM) interval when shipped from the factory. Before using the unit, be sure to set it to the AM/FM tuning interval (span) used in your area. To check the tuning span currently selected: 1 Press the ON/STAND-BY button to turn the power on. 2 Press the FUNCTION button until "AM" appears on the display. ● If "AM 531 kHz" is displayed, it means that AM stations have been adjusted for a 9 kHz span and FM stations for 50 kHz span. If "AM 530 kHz" is displayed, AM stations have been adjusted for a 10 kHz span and FM stations for 100 kHz span. To change from a 9 kHz AM (50 kHz FM) interval to a 10 kHz AM (100 kHz FM) interval: 1 Press the ON/STAND-BY button to enter the stand-by mode. 2 Hold down the button and the MEMORY/SET button for at least 4 seconds. Release the buttons when "AM SP 10 kHz" and "FM SP 100 kHz" are displayed alternately. ● The clock display will reappear. To return to a 9 kHz AM (50 kHz FM) interval: 1 Press the ON/STAND-BY button to enter the stand-by mode. 2 Hold down the button and the MEMORY/SET button for at least 4 seconds. Release the buttons when "AM SP 9 kHz" and "FM SP 50 kHz" are displayed alternately. ● The clock display will reappear. Caution: ● When the unit is left for a few hours after the span has been switched and the AC power lead disconnected, the AM span will be automatically returned to 9 kHz (FM span to 50 kHz). If this happens, set the span again. ● When the span is switched, all the memorised stations will be cancelled. –8– XL-3000V Listening to a CD 1 2 Press the ON/STAND-BY button to turn the power on. Press the FUNCTION button until "CD" or "NO DISC" appears on the display. When operating with the remote control, press the CD button. 3 Press the (OPEN/CLOSE) button to open the disc compartment. 4 Place a CD on the spindle, label side up. Be sure to place 8 cm (3") disc in the middle of a disc holder. 5 Press the (OPEN/ CLOSE) button to close the disc comTotal number of partment. Total playing time tracks 6 Press the ( ) button to start playback from track 1. When the last track on the disc has finished playing, the unit will stop automatically. To interrupt playback: Main unit operation: Press the button. To resume playback from the same point, press the Remote control operation: Press the button. To resume playback from the same point, press the button again. button. To stop playback: Press the button. To remove the CD: Whilst in the stop mode, press the (OPEN/CLOSE) button. Press the disc eject button and remove the CD. Listening to the Radio 1 2 Press the ON/STAND-BY button to turn the power on. Press the FUNCTION button until "FM" or "AM" appears on the display. When operating with the remote control, press the TUNER button, and then the BAND button to select "FM" or "AM". 3 Press the TUNING ( sired station. or ) button to tune in to the de- Manual tuning: Press the TUNING button as many times as required to tune in to the desired station. Auto tuning: When the TUNING button is pressed for more than 0.5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Notes: ● This can be operated by pressing the TUN. ( or ) button on the remote control. ● When radio interference occurs, auto scan tuning may stop automatically at that point. ● Auto scan tuning will skip weak signal stations. ● To stop the auto tuning, press the TUNING button again. FM stereo mode indicator FM stereo receiving indicator To receive an FM stereo transmission: Press the FUNCTION (BAND) button to display the "ST" indicator. ● " " will appear when an FM broadcast is in stereo. ● If the FM reception is weak, press the FUNCTION (BAND) button to extinguish the "ST" indicator. The reception changes to monaural, and the sound becomes clearer. After use: Press the ON/STAND-BY button to enter the power stand-by mode. –9– XL-3000V DISASSEMBLY STEP Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take compact disc out of the unit. 2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit. 3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange the leads where they were before disassembling. 4. Take sufficient care on static electricity of integrated circuits and other circuits when servicing. (A1) x2 ø3 x10mm 1 2 Top Cabinet Fan Motor Rear Panel Top Cabinet/ Video PWB 1. Screw .................. (B1) x2 2. Hook .................... (B2) x5 3. Flat Cable ............ (B3) x2 4. Socket ................. (B4) x9 5. Screw .................. (B5) x3 6. Socket ................. (B6) x1 10-2 10-1 10-1,2 10-1 11-1 10-2 3 Tuner PWB 1. Screw .................. (C1) x2 2. Socket ................. (C2) x1 11-1 4 Power PWB 1. Socket ................. (D1) x2 2. Hook .................... (D2) x1 11-1 5 Main PWB 1. Socket ................. (E1) x1 2. Screw .................. (E2) x8 11-1 6 Display PWB 1. Screw .................. (F1) x4 2. Hook .................... (F2) x4 11-2 7 CD Mechanism 1. Screw .................. (G1) x4 11-2 8 Gear Box 1. Screw .................. (H1) x1 2. Holder .................. (H2) x1 3. Lever ................... (H3) x1 4. Screw .................. (H4) x3 5. Lever ................... (H5) x1 11-2 9 LED PWB 1. Screw .................. (J1) x1 11-2 (A4) x2 ø3 x8mm Note: After removing the connector for the optical pickup from the connector, wrap the conductive aluminium foil around the front end of connector remove to protect the optical pickup from electrostatic damage. Rear Panel (A1) x2 ø3 x10mm FIGURE 1. Screw .................. (A1) x7 2. Socket ................. (A2) x4 3. Screw .................. (A3) x4 4. Screw .................. (A4) x2 (A3) x3 ø3 x12mm (A1) x3 ø3 x10mm PROCEDURE REMOVAL Rear Panel/ Terminal PWB/ Fan Motor (A2) x4 Terminal PWB Figure 10-1 Top Cabinet HooK (B2) x2 (B4) x1 CD Mechanism Hook (B2) x3 (B6) x1 (B4) x2 Top Cabinet (B4) x4 Up (B3) x1 Slide Hook Bottom Cabinet (A3) x1 ø3 x10mm Lug Power PWB Bottom Cabinet Video PWB (B4) x1 (B3) x1 (B1) x2 ø2.5 x8mm Main PWB (B4) x1 Figure 10-2 – 10 – XL-3000V Power PWB Tuner PWB (D1) x2 (C1) x1 ø3 x8mm Holder PWB (E2) x7 ø3 x8mm (E1) x1 (C2) x1 (B5) x3 ø3 x6mm Tuner PWB Video PWB Main PWB Bracket Bottom Cabinet (C1) x1 ø3 x6mm Hook (D2) x1 Washer Bracket Main PWB (E2) x1 ø3 x14mm Figure 11-1 (H4) x2 ø2.5 x10mm Gear Box (H3) x1 (H1) x1 ø3 x8mm STEP 1 REMOVAL Speaker (H5) x1 Switch PWB (H4) x1 ø2.5 x8mm (H2) x1 Bracket Shield Cover (J1) x1 ø2.5 x10mm (G1) x2 ø2.5 x10mm Holder PWB Front Panel ( A2 ) x1 ( A3 ) x2 ø4 x12mm ( A3 ) x4 ø4 x12mm Hook (F2) x4 Display PWB 11-3 Net Frame ( A1 ) x1 (F1) x4 ø2.5 x10mm CD Mechanism FIGURE Tweeter (G1) x2 ø2.5 x10mm Holder PWB LED PWB PROCEDURE 1. Net Frame ........... (A1) x1 2. Front Panel ......... (A2) x1 3. Screw .................. (A3) x6 Woofer Screwdriver Top Cabinet Figure 11-2 Figure 11-3 – 11 – XL-3000V REMOVING AND REINSTALLING THE MAIN PARTS How to remove the CD lid (See Fig. 12-1.) Perform steps 1,2 and 8 of the disassembly method to remove the gear box. (See page 10,11) 1. Remove the switch PWB. 2. Remove the screws (A1) x 4 pcs., to remove the gear box lid. 3. Remove the gears (A2) x 1 pc. and (A3) x 1 pc. 4. Remove the screws (A4) x 2 pcs., to remove the motor. Caution: Be careful so that the gear is not damaged. (The damage gear emits noise during searching.) CD Lid Motor (A2) x1 (A1) x1 ø2.5 x14mm (A1) x2 ø2.5 x12mm (A4) x2 ø2 x5mm (A3) x1 Switch PWB Gear Box Lid (A1) x1 ø2.5 x10mm Figure 12-1 CD MECHANISM SECTION (See Fig. 12-2.) (A1) x4 Perform steps 1,2 and 7 of the disassembly method to remove the CD mechanism. (See page 10,11) 1. Remove the mechanism cover, paying attention to the pawls (A1) x 4 pcs. 2. Remove the screws (A2) x 2 pcs., to remove the shaft (A3) x 1 pc. 3. Remove the stop washer (A4) x 1 pc., to remove the gear (A5) x 1 pc. 4. Remove the pickup. Note: After removing the connector for the optical pickup from the connector, wrap the conductive aluminium foil around the front end of connector remove to protect the optical pickup from electrostatic damage. Mechanism Cover (A2) x2 ø2.6 x6mm CD Mechanism Shaft (A3) x1 Gear (A5) x1 Stop Washer (A4) x1 Pickup unit Figure 12-2 – 12 – XL-3000V ADJUSTMENT TUNER SECTION fL: Low-range frequency fH: High-range frequency • AM IF/RF Signal generator: 400 Hz, 30%, AM modulated Frequency Frequency Display • FM Mute Level Signal generator: 1 kHz, 40 kHz dev., FM modulated Setting/ Instrument Adjusting Connection Parts T351 *1 AM IF 450 kHz 1,602 kHz AM Band Coverage — 531 kHz (fL): T306 *2 1.1 ± 0.1 V AM Tracking 990 kHz 990 kHz (fL): T302 98.00 MHz (25±1 dBµV) VR351*1 Input: SO301 Output: Speaker Terminal • Check FM VT Signal generator: 1 kHz, 40 kHz dev., FM modulated Frequency 10.7 MHz Frequency Display 98.0 MHz Setting/ Adjusting Parts FM Band Coverage — 87.50 MHz FM RF 98.00 MHz (10~30 db) 98.00 MHz Setting/ Instrument Adjusting Connection Parts (fL): L303 *1 3.4 ± 0.1 V L302 *2 Instrument Connection 87.5 MHz 87.5 MHz 3.4 V ± 0.1 V TP301 108 MHz 108 MHz 7.8 V ± 1.0 V TP301 FM Preset No. 1 2 3 4 5 • FM RF Signal generator: 1 kHz, 75 kHz dev., FM modulated Frequency Display Check Point • Setting the Test Mode Keeping the FF/PRESET UP button and MEMORY/SET button pressed, turn on ON/STAND-BY. Then, the frequency is initially set in the memory as shown in Table. Call it with the VOLUME UP/DOWN button to use it for adjustment and check of tuner circuit. Instrument Connection T304(Turn Input: Pin 1 of the core of IC301 T304 fully counterclockwise.) Frequency Display Frequency • FM Detection Signal generator: 10.7 MHz, FM sweep generator FM IF 98.00 MHz Instrument Connection *1. Adjust so that an output signal appears. *1 *1. Input: Antenna, Output: Speaker Terminal *2. Input: Input is not connected, Output: TP301 Test Stage Adjusting Parts Display Frequency 87.50 MHz 108.00 MHz 98.00 MHz 90.20 MHz 106.00 MHz FM 75 SO301 OHMS ANTENNA TERMINAL AM Preset No. 6 7 8 9 10 531 kHz 1,602 kHz 990 kHz 612 kHz 1,404 kHz TUNER PWB-A2 GND AM *1. Input: Antenna, Output: TP301 *2. Input: Antenna, Output: Speaker Terminal TP301 20 FM ANT. FM RF IC301 1 IC302 L302 FM OSC. L303 FM Band Coverage fL T302 AM Tracking fL T304 FM IF VR351 FM Mute Level T351 AM IF IC303 T306 AM Band Coverage fL Figure 13-1 ADJUSTMENT POINTS – 13 – XL-3000V CD SECTION Since this CD system incorporates the following automatic adjustment function, when the pickup is replaced, it is not necessary to readjust it. VIDEO CD SECTION A-BEX TEST VIDEO CD Model No. TVD-581 TVD-581A SET • Measurement of oscillation frequency Disc Instrument Connection Adjusting Point CD Stop TC100V 27.00000 MHz ± 160 Hz Specified Value Video Output Terminal 1 of R163V and 2 of C183V Video Input Terminal • Checking of video output signal Checking of color bar Instrument Connection Adjusting Point Disc Track 2 Video output terminal TV Figure 14-3 Checking of video output signal Chroma Peak Level 100 ± 15 IRE IH (59.94Hz/NTSC) VIDEO PWB-D 100 100 88.5 100 IRE 75 75 Color bar signal waveform 70 1 PCLK2X (0.714V) 140 IRE IC15V IC14V (1V) R163V C183V 2 GND 41.5 33.5 20 5 40 IRE (0.286V) 0 Blue Red Green Magenta Color Burst Figure 14-1 ADJUSTMENT POINTS Cyan -40 Yellow 40 IRE -25 -25 Gray X1V Horizontal sync signal -13.5 -20 TC100V Figure 14-4 SET GND Vectorscope Waveform monitor or oscilloscope TV monitor Figure 14-2 Measurement of oscillation frequency Figure 14-5 – 14 – Blue 75 ohms Red Magenta Green Cyan Yellow Gray VIideo Output Terminal XL-3000V Checking of vector scope waveform Disc Checking Track 2 VIDEO OUT Setting Checking Item Set the phase of color burst signal (B) to 180°-360° line. Phase check ± 10° ( Check that the setting is within the illustrated range.) V cy R-Y I R g Q MG R MG 75% YL YL b B-Y 75% -Q B B yl G CY G U CY -I [NTSC] [PAL] Figure 15-1 Checking the black-and-white level Disc Track 16 Checking VIDEO OUT Checking Item Output level 100 ± 10 IRE 100% Luminance 100IRE 40IRE 40IRE Horizontal Interval reference signal 100% WHITE LEVEL Figure 15-2 – 15 – mg XL-3000V TEST MODE • The TUNER TEST2 mode is obtained with >> The test mode applied to this microcomputer has three modes, namely the ordinary test mode for adjustment or measurement, the aging test mode, and the self-diagnosis test mode for selfjudgment in case of final product inspection. + MEMORY + ON/STAND-BY. -> Turn off AC in the TEST2 mode to restore the initial state. 1. Turning on the test mode For obtaining each test mode, press the ON/STAND-BY button, while keeping pressing the following two buttons in the ordinary stand-by mode (power off ). In this case, the main unit buttons are valid. When turning the ON/STANDBY on with remote control buttons, test modes are not obtained. Turn off POWER to protect the memory of TEST2 mode. Turn off POWER again to obtain the ordinary operation while the data is stored in the memory (besides TUNER). If AC OFF state is maintained in this state for about 1/2 day, start is executed in the initial state. [Ordinary test mode] 1. Tuner Test Mode (TEST 2) .......................REW/PRESET DOWN + CD PLAY 2. Electronic Volume Test Mode (TEST 3) .......................REW/PRESET DOWN + FF/PRESET UP 3. Timer Test Mode (TEST 4) .......................FUNCTION + VOLUME UP 4. LCD Test Mode (TEST 5) .......................FUNCTION + FF/PRESET UP 5. Electric CD Lid Aging Test Mode (TEST 8) .......................FUNCTION + CD PLAY • To clear the whole memory, insert the AC cord, pressing MEMORY + CD PLAY. 3. Preset frequencies for various destinations (random preset memory) CH [Self-diagnosis Test Mode] 1. Button input diagnosis test mode (TEST6) .......................FUNCTION + VOLUME Processes are different depending on destinations at initial settings. 1 2 3 4 5 2. Tuner Test Mode (TEST 2) 1. Outline of tuner (radio) test mode The tuner test mode is intended to store the adjustment and measurement frequencies in the preset memory CH. When adjusting the tuner section in the production line, adjusting personnel are not required to set frequency. 2. Details of tuner test mode Press the "REW/PRESET DOWN" and "CD PLAY" buttons in POWER OFF state and turn on the power by the use of "ON/STAND-BY" button to preset and store frequency for adjustment and measurement of destination specified by the AREA terminal in the preset memory CH. However, Ordinary 1 and Ordinary 2 are stored in the destinations (selected by SPAN switching operation) when the test mode is obtained. ("FF " + "MEMORY/SET" KEY SPAN CHANGE) (As for frequencies to be preset and stored for each destination, refer to item 3.) The tuner test mode is started from preset No.1. The operations of test mode are identical with the ordinary operations of TUNER function. FUNCTION switching is invalid. CH 6 7 8 9 10 CH 16-25 26 27 28 29 30 BAND FM STEREO BAND AM BAND FM MONO FM FM 87.50 MHz FM108.00 MHz FM 98.00 MHz FM 90.20 MHz FM106.00 MHz AM AM 531 kHz AM1602 kHz AM 990 kHz AM 612 kHz AM1404 kHz FM FM106.00 MHz FM 90.20 MHz FM 98.00 MHz FM108.00 MHz FM 87.50 MHz • The slant line sections of the table store no memory. It is necessary to discard the content of preset memory when the tuner test mode is ended; be sure to write "0000" or "1111" bits in the memory to be checked for judging memory error at initial setting and to initialize memory. When the tuner test mode is obtained, the following display lights for one second. – 16 – XL-3000V 3. Electronic volume Test Mode (TEST 3) When this test mode is obtained, the following display lights for one second. 5. LCD Test Mode (TEST 5) When the LCD test mode is obtained, all the LCD segments are lighted. Then pressing the "PLAY" button switches display as below. Lighting of all segments In this mode, volume is -14 dB (STEP28), BASS/TREBLE is set to 0 (0 dB) and SURROUND mode to OFF, and startup function to CD, respectively. The button operations in the test mode are the same as those of ordinary operation except volume UP/DOWN. (1) The display is the same as that of ordinary operation except test mode setting. (2) Unlike the ordinary state, the volume is controlled with the volume UP/DOWN button in accordance with the following three steps. Lighting of odd segments Lighting of even segments <-> Volume- ∞ (STEP 0) <-> Volume-14 dB (STEP 23) Volume-0 (STEP 30) (3) BASS/TREBLE and SURROUND are switched when button is pressed. 4. Timer test Mode (TEST 4) When this test mode is obtained, the following display lights for one second. Set the current time and timer time according to the following procedure to reproduce the timer. 1. Set the current time to 1:00, the timer to ON time 1:05, the function to CD, and volume to STEP 12, respectively. One minute is counted as one second, and the timer is reproduced. The fade-in (when playback is started) is executed at a rate of one step for 1 sec. After completion of fade-in, the fade-out is executed at a rate of one step for 1 sec (WAIT 1 sec inserted). After completion of fade-out, the power is turned off (after WAIT 1 sec), and the mode is shifted to the standby. The display during operation is the same as that of ordinary timer operation. – 17 – XL-3000V 6. Key input diagnosis Test Mode (TEST 6) When the test mode is obtained, the following is displayed. 7. Electric CD lid Aging Test Mode (TEST 8) (Only for model with electric CD lid) Outline OPEN/CLOSE operations of electric CD lid are repeated. The number of repeated times and time period are monitored. If the lid does not move to the regular position after the specified time, operation is stopped. When an error is detected by [CLID_PRO] during CLOSE, operation is also stopped. This test mode is intended to check whether all the main unit buttons can be detected. Accordingly, in this test mode, it is checked whether the "ON/STAND-BY" button was pressed after all the buttons shown below were pressed. If the result is OK, OK is displayed. If any one of keys was not pressed, an error is displayed. In both cases of OK termination or error termination, the mode is shifted to the standby mode if the "ON/STAND-BY" button is pressed subsequently. a. POWER ON for function AUX CD lid position is checked. CLOSE position: Operation proceeds to the next process. Position other than CLOSE: After the lid moves to CLOSE,operation proceeds to the next process. b. CD lid operation started OPEN operation WAIT 1 second CLOSE operation WAIT 1 second c. Operations above are repeated. Specified monitoring time OPEN operation: 5 seconds CLOSE operation: 5 seconds All models using this type of microcomputer are not always provided with the same buttons. Since the buttons used are different depending on models, types of buttons to be used are determined by whether RDS, SURROUND, and an electric lid are available at the initial setting by MODEL port. The order of buttons to be pressed is not determined. Accordingly, it is checked whether all buttons have been pressed. d. Display OPEN>CLOSE is counted as 1. I to 59999 are counted; if the count is over 59999, display is returned to 0 to repeat counting. 1. PU-IN buttons: REW/PRESET DOWN + CD STOP Since this model is provided with SURROUND (HAVE OR NOT), RDS (HAVE OR NOT), and electric CD lid, the following 10 buttons are detected as all buttons. PLAY, BASS/TREBLE, FUNCTION, VOLUME UP/ DOWN, MEMORY/SET, REW, FF, STOP, CD-OPEN/ CLOSE The OK/NG display of test result is as follows. Display when the lid does not move to the regular position after the specified time (Ex: Defective operation occurring in the middle of 1538.) Highlight display of stop when an error is detected by [CLID-PRO] (Ex: Defective operation occurring in the middle of 1538.) – 18 – XL-3000V NOTES ON SCHEMATIC DIAGRAM • Resistor: To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type. • Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means micro-micro-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression “capacitance/withstand voltage” is used. (CH), (TH), (RH), (UJ): Temperature compensation (ML): Mylar type (P.P.): Polypropylene type • Schematic diagram and Wiring Side of P.W.Board for this model are subject to change for improvement without prior notice. REF. NO DESCRIPTION NSW801 PICKUP IN SW651 VOLTAGE SELECTOR SW709 ON/STAND-BY SW710 CD LID OPEN/CLOSE • The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given. 1. In the tuner section, ( ) : AM mode : FM stereo mode 2. In the CD section, the CD is stopped. • Parts marked with “ ”( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. POSITION REF. NO ON—OFF SW718 VOLUME DOWN DESCRIPTION POSITION 110V SW721 MEMORY/SET ON—OFF ON—OFF SW722 BASS/TREBLE ON—OFF ON—OFF SW725 CD STOP/TUNING DOWN ON—OFF REW/PRESET DOWN ON—OFF ON—OFF SW711 FF/PRESET UP ON—OFF SW726 SW712 CD PLAY/PAUSE/TUNING UP ON—OFF SW727 FUNCTION ON—OFF SW713 VOLUME UP ON—OFF SW802 CD LID ON—OFF FRONT VIEW E C B (S) (G) (D) (1) (2) (3) 2SB562 C 2SC535 C 2SK246 GR 2SC1740 SR 2SD1858 R2 KRA102 M KRC102 M KRC104 M KRC107 M KTA1266 GR KTA1268 GR KTC3199 GR KTC3200 GR FRONT VIEW FRONT VIEW B C E 2SD2012 Y DB5306X 1 2 3 SVC348S KDV147C Figure 19 TYPES OF TRANSISTOR AND LED – 19 – XL-3000V FROM VIDEO PWB FROM DISPLAY PWB 10 9 8 7 6 5 4 3 2 1 1 4 5 6 TU 7 SD FM ST DO CL +8V +5V D_GND L–CH R–CH Q902 A_GND VDAC Q901 11 10 9 8 CNP307 A_GND CLID_DW CLID_UP CLID_PRO CLID_SW FAN_DEC AMP_DEC CD_STB DIMMER LIGHT FAN +B4 3 LED PWB CNP702 Q804 Q805 2 +B2 SWITCH PWB +B4 Q907 IC805 TA7291S CD LID MOTOR DRIVER SW802 CD LID OPEN/CLOSE Q804 Q805 Q802 8 1 9 5 2 3 6 7 +B1 M_GND Q908 M_GND Q908 +B8 SO401 M801 CD LID OPEN/CLOSE MOTOR VIDEO OUT R-CH M +B4 VIDEO/AUX INPUT 5V +B7 Q861 CD_6R2V L-CH M802 FAN MOTOR +B5 + SP+ SP– SP+ SL– PU-IN GND – + – M NM802 SPINDLE MOTOR M NM801 SLED MOTOR CNP810 1 2 M CNP807 1 2 M_GND GND MUTE REG O TRB VIN4 VG1 VIN1 VO4+ VO4VO1+ GND VO1- 21 22 23 24 25 26 27 28 +B5 16 17 18 19 BIAS VG4 VO3+ VIN3 VG3 VCC VCC PO1+ VO3- PO1- OPO GND VO2VO2+ VIN2 VG2 13 12 11 10 9 8 7 6 5 4 3 2 1 NSW801 PICKUP IN J801 DIGITAL OUT CD MOTOR PWB IC804 MM1469XH FOCUS/TRACKING/ SPIN/SLED DRIVER 1 2 3 TERMIN PWB FO TR PU_IN LRCK BCK DATA FMO 3 DOUT 9 /RST BUS0 BUS1 BUS2 BUS3 BUCK /CCE SEL 57 2VREF 56 TEBC RFGC VREF TRO 5 LRCK 7 BCK 8 AOUT IC802 TC9462F SERVO/SIGNAL CONTROL CNS801 X801 16.93MHz 78 XI 79 XO FOO TEZI TEI TSIN SBAD FEI 52 51 50 49 48 47 46 45 44 43 PICKUP UN FOCUS COIL TRACKING COIL 13 14 15 16 17 18 19 20 21 22 23 24 RFRP 42 RFCT 40 RFI 38 14 VDD 23 VDD VCOREV PVREV LPFO LPFN 39 AVDD 62 VDD 94 VDD 33 32 31 D_GND DVSR DVSL M_GND XVSS 81 86 PXI 6 15 24 63 71 72 73 74 77 95 VSS VSS TESI01 P2VREF 25 36 D_GND 34 TMAX 30 PDO 28 76 VDD 80 XVDD VSS TESIN +B7 TESIOO 12 100 90 91 92 93 96 97 VSS 8 9 10 11 /RST BUS0 BUS1 BUS2 BUS3 BUCK /CCE 53 VSS 2 3 4 5 6 7 55 AVSS TO VIDEO PWB 1 DMO +B2 SBAD FEO FEN VRO RFRP RFIS RFGO RFGC AGCI RFO GND RFN TEO TEN 2VRO TEB SEL LDO MDI TN1 TPI FPI FNI VCC 12 11 10 9 8 7 6 5 4 3 2 1 IC801 TA2109F SERVO PRE AMP. A_GND +B7 SWITCHING LD Q801 E F B A MON +B7 C 1/2V +B7 Figure 20 BLOCK DIAGRAM (1/6) – 20 – 5V XL-3000V FROM DISPLAY PWB 1 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 IC201 KIA4558P SURROUND CONTROL TO TUNER PWB R-CH IN 5V P_STB A_24V D_GND DI CD +B P_MUTE CL CE SD DO STEREO FM ST DO CL CE DI A_12V D_GND TUN L TUN R A_GND CNP703 R-CH OUT SURROUND ON/OFF SURROUND Q203 5 6 7 8 4 3 2 1 +B6 A_12V Q201 +B8 +B3 +B6 L-CH OUT L-CH IN R-CH OUT AUX R 14 13 10 11 12 9 8 7 6 4 5 3 2 1 VSS 15 DI CE TUN R CD R NC VDD LOGIC 16 19 18 20 21 22 23 24 25 26 27 28 29 IC401 LC75342M FUNCTION/VOLUME EQUALIZER SO601 SPEAKER TERMINAL AUX L 30 CL 17 CD L TUN L L-CH OUT +B6 A_12V IC601 STK40202 POWER AMP. PRE –VCC 8 9 12 GND –VCC 4 +VE2 –VE2 +VCC L-CH 1 15 R-CH + PRE +VCC IN1 RMINAL PWB IN2 Q601 Q602 +VE1 –VE1 MUTE +B7 6 7 10 11 L-CH R-CH 13 R-CH + J601 HEADPHONES 3 2 1 +B –B IC682 KIA7805API Q101 Q104 F651 T3.15A L 250V D651~D654 VOLTAGE REGULATOR 2 –B F652 T3.15A L 250V A_GND F653 T1.6A L 250V Q904 P UNIT 1 2 3 4 5 1 2 3 4 5 T651 TF D_GND Q608 +B5 N +B3 4 3 2 1 IC681 KIA7805API VOLTAGE REGULATOR 3 1 D_GND 1 3 5 7 9 1 CNP651 3 5 7 9 Q681 2 VOLTAGE REGULATOR D688 1N4004 Q607 VOLTAGE REGULATOR Q606 CNP707 VOLTAGE REGULATOR FROM DISPLAY PWB D657~D660 Q610 OIL USWD_5R6V IL POWER TRANSFORMER (MAIN) P_CONT Q683 CD_6R2V CD +B RLY601 Q609 M_12V +B4 1 2 CNP652 FROM DISPLAY PWB D681~D684 +B8 5V Q605 F654 T.F 2A,250V Q903 VOLTAGE REGULATOR +B6 A_12V 110V 127V 220V 230~240V VOLTAGE REGULATOR CNP801 1 A_24V 3 4 5 9 10 Q103 Q102 +B1 L-CH POWER PWB-B Q603 Q604 MAIN PWB AC 110/127/220/ 230~240V, 50/60Hz Figure 21 BLOCK DIAGRAM (2/6) – 21 – T681 POWER TRANSFORMER (SUB) SO655 AC INPUT SOCKET AC 110/127/220/ 230~240V, 50/60Hz AC POWER SUPPLY CORD SW651 VOLTAGE SELECTOR XL-3000V AM Tracking fL FM MUTE LEVEL T302 AM X3 456 GND BF301 2 1 3 1 2 3 4 5 6 1 8 7 FM IF 9 FM IF Q306 CF303 2 19 18 3 4 FM IF AM IF AM IF CF302 T351 CF352 5 6 FM DET STEREO AM LOW CUT FM/AM OUT 20 SD IC301 TA7358AP FM FRONT END BAD PASS FILTER 21 AM IF IN GND FM IF AM OSC OUT IN AM MIX OUT AM OSC IN REG AM Band Coverage fL SO301 ANTENNA TERMINAL 22 VSM 24 23 VR351 T306 +5V AM RF IN FM 75ohms FM AFC +5V VD301 7 FM +B T304 TP301 +5V Q302 VT +5V VD302 DI CL DO FM MUTE VDD 17 1 PD 18 AIN 19 CE X352 4.5MHz 22 21 20 AOUT FM +B VSS L303 FM OSC. FM Band Coverage fL FM RF X IN X OUT L302 FM ANT. IC302 LC72131 PLL(TUNER) FM +B VD303 3 4 5 6 7 8 1 DISPLAY PWB LCD701 LCD DISPLAY 4 1 100 67 SEG33 6 VLC2 38 SEG0 5 VLC3 5 COM3 4 COM0 1 CLID_DW CLID_UP CLID_PRO 7 VLC1 8 VDD FAN 9 OSC2 10 OSC1 X701 IC701 IX0038SJ SYSTEM MICROCOMPUTER/ FL DRIVER 11 VSS 8MHz X702 12 XI 13 XO 32.768kHz 25 26 27 34 RESET 2 Q701 Q702 Q703 RX701 REMOTE SENSOR LAMP PWB Q708 A_24V LMP701 SWITCHING Q707 GND Figure 22 BLOCK DIAGRAM (3/6) – 22 – Q709 5V Q706 SWITCHING SD CD+B STB 43 44 45 46 49 50 4 1 STEREO 37 38 39 P–MUTE 32 P–STB USWD_5R6V SURR 47 P–CONT CE 18 KEY2 P_CONT CL 17 KEY1 D_GND DI 3 16 CLID_SW SW710 DO 3 SW709 REMOCON 2 24 VREF+ POWER 2 VD_DI VD_DO ACK BUSY CLID_OUT 15 VREF– RESET 1 14 MMOD SYS_STOP CNW707 CNS707 1 CNS652 TO MAIN PWB TO POWER PWB SW711~713 SW718 SW721,722 SW725~727 CD_STB AMP_DEC LIGHT DIMMER MOT_DEC B-LIGHT XL-3000V TUNER PWB SWITCHING Q351 AM IF AM IF T351 CF352 10 11 12 IC303 LA1832S FM IF DET./ FM MPX./AM IF 9 13 MO/ST R-CH OUT L-CH OUT MPX VCO 8 15 14 PHASE (AM/FM) 7 VCC FM DET STEREO 6 16 PHASE 5 CF351 4 SD REG 3 17 MPX IN 18 IF OUT 19 AM LOW CUT FM/AM OUT AM RF IN 20 VSM 21 AM IF IN GND 22 FM AFC AM OSC IN X351 456kHz +5V +5V SD 7 8 AM IN 9 10 11 10 DO VOLTAGE REGULATOR 9 CL +5V 8 CE 7 DI FM +B Q360 6 A_12V +B 5 D_GND 4 TUN_L TO MAIN PWB 6 IF REQ IF IN 5 MO/ST 4 14 13 12 FM FM 3 1 VDD MUTE FM IN DO PD CL 17 16 15 DI 18 CE AOUT VSS X IN X OUT 19 AIN PLL(TUNER) ZD351 22 21 20 11 FM ST +5V 3 TUN_R 2 A_GND 1 CNS307 67 FAN 55 60 52 53 54 21 CD_STB AMP_DEC LIGHT DIMMER MOT_DEC SEG33 25 26 27 34 VD_DI VD_DO ACK 29 28 30 31 35 1 2 3 4 5 6 7 BUSY CLID_OUT GND STB STB 40 CNW704 SD CD+B VD_DI VD_DO ACK BUSY CLID_OUT STEREO P–MUTE P–STB SURR CE CL DO C701 0038SJ CROCOMPUTER/ DRIVER DI CNW702 CLID_DW 1 CLID_UP 2 CLID_PRO 3 CLID_SW 4 FAN 5 CD_STB 6 AMP_DEC 7 LIGHT 8 DIMMER 9 FAN_DEC 10 CLID_DW 57 CLID_UP 56 CLID_PRO 20 CNS702 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 TO MAIN PWB 0 TO VIDEO PWB 38 CNS704 B-LIGHT 51 CNS703 43 44 45 46 49 50 SD STEREO DO CL CE DI CD+B P_MUTE P_STB A_24V A_24V D_GND SURROUND 5V 5V – 23 – 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 13 CNW703A Figure 23 BLOCK DIAGRAM (4/6) 1 TO MAIN PWB 5 SEG0 LCD701 CD DISPLAY XL-3000V VCC 32 1 VPP 2 A16 REGULATOR A18 31 A17 30 3 A15 4 A12 Q11V A14 29 A13 28 5 A7 6 A6 3.3V A8 27 A9 26 7 A5 8 A4 A11 25 OE 24 9 A3 10 A2 A10 23 CE 22 11 A1 12 A0 D7 21 13 D0 D6 20 14 D1 15 D2 D5 19 16 VSS D3 17 D4 18 IC10V IX0041SJ ROM 256K x 16 R163V 83 LA13 VD_DI VCC3 AUX5 DSC_STB AUX6 /MRQ AUX7/STB LD1 LDO LD2 LD3 LD4 LD5 LD6 LD7 LOE LWR LSCE1 LROMCE LA0 LSCE0 LA1 LA2 LA3 LA4 LA5 LA6 LA7 LA8 LA9 LA10 VSS 81 VCC 82 LA12 LA11 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 VSSK 5 0 AUX4 49 AUX3/VD_DI 48 84 LA14 AUX2/VD_DO 47 85 LA15 AUX1/DSADATA 46 86 LA16 AUX0/DSAACK 45 87 LA17 PCLKQSCN 44 88 AUDIO_CLK PCLK2XSCN 43 89 AUDIO_DATA DCLK 42 HSYNC 41 VSYNC 40 IC15V ES3880F VIDEO CD DECODER 90 BCLK 91 LR 92 DRAS1/DOE YUV7 39 RESET DBUS15 DBUS14 DBUS13 DBUS12 DBUS11 DBUS10 DA5 DBUS9 DA4 DBUS8 DA3 DBUS7 DA2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 VCC D3 D2 D1 D0 VCC VSS D12 D13 D14 D15 VSS 1 D4 2 D5 3 D11 4 D10 5 D6 6 D7 7 D9 8 D8 LCAS WE A0 A7 UCAS A1 A6 RAS A2 A5 OE A3 A4 A8 VCC VSS 20 19 18 17 16 15 14 13 12 11 10 9 VCC3 31 VSS DA8 DA1 3 2 DA7 DA0 1 DA6 DWE YUV0 32 VCC3 DRAS DBUS6 YUV1 33 99 DCAS 100 VSS DBUS5 YUV2 34 98 TDMFS DBUS4 YUV3 35 97 TDMDR DBUS3 YUV4 36 96 TDMCLK DBUS2 YUV5 37 95 RWS DBUS1 YUV6 38 94 RBCLK DBUS0 93 RSD 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 IC16V IX0025SJ D-RAM 256K x 16 Figure 24 BLOCK DIAGRAM (5/6) – 24 – VD_DO 27M VDAC AGNDV – + +– 6 5 1 L_CH 2 AGNDA R_CH 3 +5V 4 8 DGND +12V V_AMP 2 1 3 2 4 3 5 4 6 5 7 6 8 7 9 8 Q12V CNP804V BUSY 1 VD_DI 2 VD_DO 3 ACK 4 STB 5 DGND 6 CLID_OUT 7 FROM DISPLAY PWB 7 1 TC100V V 27MHz X1V 27MHz 82 HSYNC 83 DSC_D6 VSSA VREF RSET VREFM COMP VSSAV VSSAV VCCA CDAC VCCA YDAC VSSAV VDAC VSSAV VCC ACAP AUX6 AUX5 AUX4 AUX3 VSS XOUT XIN VCC VSS VSS VCC PCLK MIC2 50 MIC1 49 AOL+ 48 84 VSYNC AOL- 47 85 DSC_D5 AOR- 46 86 YUV7 AOR+ 45 87 YUV6 VCCA 44 88 YUV5 VREFP 43 89 YUV4 VCM 42 IC14V ES3883F VIDEO CD ENCODER 90 VCC 91 VSS 92 YUV3 VSSA 41 AUX15 40 AUX14 39 93 DSC_D4 LA18/AUX13 38 94 YUV2 RBCK 37 95 DSC_D3 AUX12 36 96 YUV1 AUX11 35 97 DSC_D2 AUX10 34 98 YUV0 SQSO SQCK VSS VSS RSTOUT RWS TBCK TSD VCC 32 VSS 31 BCLK TWS AUX9 AUDIO_DATA LR AUX8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MCLK 8 VCC 6 7 MUTE 5 AUDIO_CLK 4 AUX7 AUX1 3 RST DSC_D0 2 DCLK AUX0 1 AUX2 DSC_CLK VSS 100 VSS DSC_STB VCC RSD 33 99 DSC_D1 CNP801V DGND /RST BUS0 BUS1 BUS2 BUS3 BUCK /CCE PICK_IN LRCK BCK DATA Figure 25 BLOCK DIAGRAM (6/6) – 25 – 1 2 3 4 5 6 7 8 9 10 11 12 TO MAIN PWB DSC_D7 81 PCLK2X 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 TO MAIN PWB IC11V NJM4565M BUFFER AMP. CNS802 CNW802V XL-3000V XL-3000V P35 12-A,B FROM VIDEO PWB-D CNS802 TERMINAL PWB-A4 2 3 4 5 6 7 11 10 9 8 8 7 6 5 4 3 2 1 1 2 3 4 5 6 DI CD +B CL CE SD DO STEREO SD FM ST DO CL CE DI A_12V D_GND TUN L TUN R A_GND +8V R-CH +5V D_GND L-CH CNP307 A_GNDA C852 0.0022 C853 0.0047 1 CNP802A VDAC J801 DIGITAL OUT FROM MAIN PWB-A1(2/2) CNS805 P28 1-G 3 2 1 A_GNDV A L802 CNP805 0.82µH C851 100/10 1 2 3 P33 12CNS7 P31 12-E TO CNS307 TUNER PWB-A2 CFW852 TO CHASSIS GND LUG(205) CNP810 1 2 M 1 2 FROM MAIN PWB-A1(2/2) CNS807 P28 1-A CNP807 1 2 SO401 L402 0.82µH VIDEO OUT CNP608 1 2 R-CH CNW608 CNS608 1 2 1 2 R408 R407 2.2K 2.2K R405 27K CNW607 1 2 3 R401 1K C413 0.0047 C414 220P CFW452 Q607 2SD2012 Y +B CFW451 CHASSIS GND TO CHASSIS GND LUG(205) Q610 2SD2012 Y R402 1K 1 2 3 1 2 3 CNS607 +B 19V CNW601 1 2 3 7V 7.8V 19V 7V CNP601 1 2 3 +B 1 1 2 2 3 3 CNW602 CNP602 +B F651 7 9 0.7V R688 1K R689 1K 0V Q683 KTC3199 GR +B R686 47K 12.2V R619 47 Q604 2SD2012 Y 20V D681 1N4004 D683 1N4004 D684 1N4004 POWER PWB-B T681 POWER TRANSFORMER (SUB) SO655 AC INPUT SOCKET AC 110/127/220/ 230~240V, 50/60Hz Q603 KTC3200 GR C625 10/16 +B 11.7V SW651 VOLTAGE SELECTOR C622 0.022 D602 1N4148 R624 22K Q903 KTC3199 GR 4.9V 11.2V D603 1N4148 R628 13V 100 C620 470/25 C683 2200/35 12.3V 20V R629 820 D682 1N4004 R623 22K +B 110V 127V 220V 230~240V F654 T.F 2A,250V +B Q605 2SD2012 Y CNW653 2 1 G C624 0.022 11.7V 20V 0V R685 10K +B D604 1N4148 RLY601 0.72V CNP653 20V R612 820 9.4V Q609 1 KRC107 M 4.8V 2 3 2 9.4V 3 C630 0V R613 R611 4700/25 4.7K Q608 100 1 0V KRA102 M ZD602 C629 C626 4.7/25 MTZJ9.1C 100/25 +BGND 9.2V +B D685 1N4004 D689 1N4004 0.11V R687 2.7K ZD684 MTZJ16C P_CONT 2 1 C601 0.047 9.3V Q681 KTC3199 GR ZD683 C689 0.47/50 MTZJ16C 2 0.6V 1 C688 0.047 C665 0.047 D688 1N4004 D_GND 3 9.2V IC681 KIA7805API VOLTAGE REGULATOR 5.7V ZD901 DZ24BSD 7.7V CNP651 D606 D605 1N4004 1N4004 5 C628 10/16 3 C903 10/50 R913 10 R617 33K ZD601 DZ130BSA 5.6V R912 470 C621 100/25 +B C906 100/10 1 R911 100 C627 0.022 9 Q904 KTC3200 GR 24.4V 38.9V Q606 KTC3200 GR 7 C902 220/50 C901 220/50 +B2 5 USWD_5R6V 4 3 2 1 CNP707 P32 1-E,F FROM CNS707 DISPLAY PWB-A3 F 3 R126 680(3W) R910 2.7K D659 1N4004 D660 1N4004 1 –B C126 2200/35 D901 D902 1N4004 1N4004 C658 0.1 D658 1N4004 C659 0.1 D657 1N4004 C660 C657 0.1 0.1 T1.6A L 250V + –B1 F653 T651 POWER TRANSFORMER(MAIN) E 0V R125 680(3W) R610 47 T3.15A L 250V 1 2 3 4 5 +B 5V 3 2 R614 47 CNP801 1 2 3 4 5 TF 1 7.8V D652 1N5402M C125 2200/35 F652 C654 0.1 T3.15A L 250V 0V D686 1N4004 IC682 KIA7805API VOLTAGE REGULATOR D653 1N5402M 24.9V 230~240V 220V 127V 110V D654 1N5402M C602 47/16 C651 0.1 D C904 10/50 7.8V R620 47 C D412 1N4148 R406 27K L-CH CNP607 L401 2.2µH D411 1N4148 C412 330P R621 22K C411 330P VIDEO/ AUX IN D651 1N5402M B M802 FAN MOTOR AC POWER SUPPLY CORD ZD902 DZ5.6BSB CNP652 AC 110/127/220/ 230~240V, 50/60Hz P32 1-F FROM CNS652 DISPLAY PW • NOTES ON SCHEMATIC DIAGRAM can be found on page 19. 2 3 +B 1 2 H 1 C905 100/10 4 Figure 26 SCHEMATIC DIAGRAM (1/10) – 26 – 5 6 XL-3000V P33 12-F,G FROM CNS703 DISPLAY PWB-A3 PWB-A2 1 2 3 4 5 6 7 8 9 MAIN PWB-A1(1/2) 10 11 12 13 C209 47/16 0.14V DI 28 29 D403 1N4004 C431 220P C430 100/16 D402 1N4004 D401 1N4004 +B SO601 SPEAKER TERMINAL CL DI CE C432 220P 30 C429 33/16 R439 3.9K 1K 1K 1K C433 220P CL CE 0.14V VREF VSS 27 VDD 1 TEST 2 4.8V 26 3 0V 25 0V C426 10/16 0V C424 0.1(ML) 4.8V 4 ROUT LOUT RBAS2 LBAS2 4.8V 5 C423 0.1(ML) 4.8V C421 0.1(ML) 24 4.8V RBAS1 LBAS1 4.8V 6 C425 4.8V 10/16 C422 0.1(ML) 4.8V RTRE LTRE 4.8V 23 C417 2.2/50 R215 12K R201 8.2K L +B 1 C215 R217 1/50 12K R203 100K C213 4.7/50 R205 10K R423 R424 R425 7 C419 0.0027 C407 10/16 R204 100K 10.2V 2 C203 1/50 R440 3.9K C420 0.0027 R438 6.8K C416 10/16 C418 2.2/50 RIN 4.8V LIN 4.8V L4 RSEL0 LSEL0 0V R4 0V 22 C208 100/16 C201 0.0056 3 5.1V 4 8 R437 6.8K C403 10/16 R421 1K R417 1K 21 4.8V 20 C415 10/16 19 9 10 4.8V R422 1K L3 L2 4.8V 18 4.8V 17 11 R3 L1 4.8V 12 R2 4.8V 4.8V 16 13 R1 0V C401 10/16 CD L TUN L 14 4.8V R403 1.8K 15 5V IC401 LC75342M FUNCTION/ VOLUME EQUALIZER AUX L +B R416 1K C402 10/16 R404 1.8K R415 1K AUX R R418 1K C404 10/16 TUN R CD R 8 R210 10K C211 0.0033 C408 10/16 R209 10K R214 12K R212 2.7K 5.1V 7 4.8V S Q201 2SK246 GR 5V 0V R218 R208 12K 330 C216 1/50 9.6V D201 1N4148 1 6 5.1V 4.44V 5 IC201 KIA4558P SURROUND CONTROL 0V 0V D 5V 0V G R202 8.2K C202 0.0056 R216 12K R211 2.7K R207 47K 2 5.1V Q203 KRC107 M SURROUND 3 5.1V R206 10K 5.1V FM SIGNAL C204 1/50 C214 4.7/50 C212 0.0033 R213 12K VIDEO SIGNAL CD SIGNAL 5V A_24V D_GND P_STB DI CD +B P_MUTE CL CE SD STEREO DO CNP703 R607 6.8K +B IN2 R106 470 C107 100/50 R115 56K R113 100 C111 C112 10/50 10/50 R604 10K Q602 0V KTC3199 GR C102 10/50 D606 D605 1N4004 1N4004 C628 10/16 C120 220/16 R638 4.7 CHASSIS GND L602 3µH C110 0.001 0.6V L603 10µH Q101 KTC3200 GR 0V R120 1K R-CH + C616 0.1 Q103 KTC3200 GR R121 10K Q104 KTC3200 GR 0.6V R118 47K 1.2V 0.6V L-CH R102 39K R124 47K R123 10K R122 1K C627 0.022 C106 10/50 R104 56K +B R119 33K C614 0.1 C109 3P Q102 KTA1268 GR +B R110 1K C104 3P A GND + C613 0.1 C639 0.0047 NF2 15 C640 0.0047 GND 14 0.1V PRE –VCC 13 C108 R108 0.0015 1K 0.1V +VE2 –VE2 12 C114 100/50 0V –VCC –21.7V 10 11 20.2V +VCC 21.8V 9 C116 0.022 +VE1 –VE1 BIAS –18.9V N.C. 0V PRE +VCC 20.6V NF1 8 R101 39K 0.6V .4V IN1 0V 6 7 R109 22K R637 4.7 C615 0.1 CHASSIS GND R662 330 J601 HEADPHONES R661 330 –B 5 L601 3µH R114 100 0.6V R603 10K 0V 0.1V 0.1V Q601 KTC3199 GR 0V 4 C103 R105 10/50 470 C603 33/16 2 3 R111 1K IC601 STK40202 POWER AMP. C101 10/50 +B 1 R103 1K 47/16 R634 3.3K C105 0.0015 R608 1K R609 1K R 3 2 1 4 5 9 10 C113 0.022 +B A B +B 8 +B 5.6V C905 100/10 C906 100/10 903 99 GR 4.9V +B +B +B +B 1 2 P29 11-C,D 5V A_GND M_GND 3 M_12V 4 CD_GND 5 CD_6R2V 6 902 6BSB 32 1-F FROM CNS652 DISPLAY PWB-A3 7 8 9 10 Figure 27 SCHEMATIC DIAGRAM (2/10) – 27 – 11 12 TO MAIN PWB-A1(2/2) P28 1-F P28 1-C –B A P26 3-B TO CNP807 TERMINAL PWB-A4 XL-3000V R883 8.2 CNW807 CNS807 2 1 2 1 Q805 KTA1266 GR R884 8.2 11.3V D805 1N4004 0.63V R880 3.3K R888 10K 0V R837 1K 0V 2 3 4 R873 3.3K C892 47/16 R881 470K 0.9V C893 47/16 0.7V 0V Q806 2SC535 C R866 4.7K C872 0.1 Q803 KTC3199 GR +B R864 D803 27K 1N4004 A B R882 6.8K Q807 KTC3200 GR 0.1V FAN 1 LIGHT 2 DIMMER 3 CD_STB 4 AMP_DEC 5 FAN_DEC 6 CLID_SW 7 CLID_PRO 8 CLID_UP 9 CLID_DW 10 CNP702 1 4.9V 0.64V R865 D804 27K 1N4004 D802 1N4004 0V R887 22K R813 10 +B +B +B L80 10µ CNS801 1 DGND 1 2 3 4 5 6 7 8 9 10 11 12 R836 1K R834 1K R832 1K R830 1K /RST R835 1K R833 1K R831 1K L801 D P35 12-G,H TO CNP801V VIDEO PWB-D C 11.7V R868 27K R885 22K TO MAIN PWB-A1(1/2) P27 12-G B P33 12-C,D FROM CNS702 DISPLAY PWB-A3 0V Q804 KTC3199 GR 0.57V R867 3.3K 0.67V 11.6V 0.2V R870 33K 0V 10.6V PU_IN LRCK L806 10µH BCK CNW801 12 R814 3.3K C822 220/10 R811 2.2K XVDD XO XI XVSS VDD PXO PXI VSS TESI01 TESIN /DACT /CKSE /DMOUT I03 I02 I01 I00 VSS VDD FLGD FLGC FLGB FLGA SEL 2VREF DMO FVO FMO TEBC RFGC 4 81 DVSR 82 RO 14 CNS805 7 5 FOO TEZI TEI TSIN SBAD FEI RFRP RFZI RFCT AVDD RFI SLCO AVSS VCOF VCOREV PVREV 1 TESTO /HSO UHSO EMPH LRCK VSS BCK AOUT DOUT MBOV IFP SBOK CLCK VDD VSS DATA SFSY SBSY SPCY SPDA COFS MONIT VDD TESIOO P2VREF HSSW ZDET PDO TMAXS TMAX 99 /TSMOD 100 /RST 13 2.1V 2.1V 2.1V 0V 2.1V 0V 2.4V 0V 0V 0.6V 1.7V 0V 5V 0V 4.3V 1.2V 5V 0V 0V 0V 5V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 R801 10K C838 47/10 C820 0.01 3 2 1 50 VREF 49 TRO 6 IC802 TC9462F SERVO/SIGNAL CONTROL R851 330 3 2 1 11 C829 100/10 R810 3.3K 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 C810 0.001 2.1V 2.1V R809 10K 2.2V 2.2V R808 C809 0.0047 2.2V 3.3K 2.1V 2.1V 2.2V 2.1V C807 0.033 2.1V R807 2.1V 10K 5V C806 0.0047 2.1V 2.1V C805 0.0027 0V C804 1.4V 0.01 2.1V 2.1V C803 47/10 LPFO 2.1V LPFN 2.1V R806 C802 15K 0.015 12 R804 100K R802 47K C801 100P +B CNW805 +B H • NOTES ON SCHEMATIC DIAGRAM can be found on page 19. • The numbers 1 to 15 are waveform numbers shown in page 41. 1 2 3 4 Figure 28 SCHEMATIC DIAGRAM (3/10) – 28 – 5 6 C811 47/10 C812 0.01 C813 0V 2.6V 2.2V 0V 5V 5V 0V 0V 0V 0V 0V 5V 0V 0V 0V 0V 5V 0V 5V 0V 0V 5V 0V 2.5V 4.3V 2.2V 0V DVDD DVR LO DVSL TEST1 TEST2 TEST3 BUS0 BUS1 BUS2 BUS3 VDD VSS BUCK /CCE TEST4 5V 5V 5V 0V 1.4V 0V 2.5V 0V 2.5V R852 100K R853 100K R855 100K R854 100K C836 100/10 8 C817 0.1 C818 0.1 15 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 0V 81 2.4V C830 C828 82 0.056 100/10 0V 83 2.3V 84 2.4V 85 0V 86 5V C840 87 100/10 C862 5V C869 0.001 88 R819 220P 5V 89 220 4.3V C868 90 220P 4.3V 91 4.3V C867 92 220P 4.3V C866 93 220P 5V 94 0V +B 95 4V 96 3.3V C865 97 220P C835 5V 98 0.056 5V 99 100 C864 C837 4.9V 220P 470P C821 0.1 C824 0.056 R812 C819 3.3K 0.1 2.1V 2.1V 1.8V X801 16.93MHz BUS0 BUS2 BUS1 BUS3 BUCK /CCE TO MAIN PWB-A1(1/2) P27 12-G P26 3-A TO CNP805 TERMINAL PWB-A4 C823 0.01 R820 1K F G C827 15P(CH) C887 0.0027 DATA E C826 15P(CH) C825 0.056 C86 470 XL-3000V 10.7V 3 R902 47K 0V 11.6V 0.57V 0V 0V 11.6V 6.1V 4.6V 4.8V 0V 1 3 4 5 6 7 8 9 CNS701 R901 2.2K 1 1 2 SWITCH PWB-A5 10.6V 4.4V Q907 KTA1266 GR 2 R904 2.2K Q908 KRC102 M Q802 KRC102 M 3 0V 3 R879 3.3K R874 2.2K 10.7V 1 1 1 1 2 2 2 3 3 3 CNW806 2 0V SW802 CD LID OPEN/CLOSE CNS806 CNP806 R905 47K D801 AUY3333 2 11.4V 0V R914 470 CNW701 1 2 CNP701 IC805 TA7291S CD LID MOTOR DRIVER C871 47/16 R873 3.3K LED PWB-A6 11.4V 2 4.1V 2 MAIN PWB-A1(2/2) 11.4V Q902 KTA1266 GR Q901 KRC102 M R877 68K 4.5V R876 150K 0V 1 CNP804 C872 0.1 +B 1 CNW804 M +B M801 CD LID OPEN/CLOSE MOTOR 5V A_GND +B 2 1 +B +B 3 4 5 6 R861 2.2K R862 2.2K 6.4V L803 10µH 1 2 M_GND M_12V D_GND CD_6R2V C870 0.001 Q861 2SB562 C 7.1V 5V P27 12-G,H TO MAIN PWB-A1(1/2) +B +B CNS804 2 R843 1K 3.2V 3.1V 2.1V 2.1V 0V 4.8V 5V 6.4V 2.1V 2.3V 4.4V 1.9V CNW803 C859 470/10 C860 0.1 MUTE REG O TRB VIN4 VG1 VIN1 VO4+ VO4VO1+ GND VO1BIAS VG4 3 3.2V 2.1V 7.0V 7.0V 2.1V 2.1V 2.1V 3.2V 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SP+ SP– SL+ SL– PU-IN GND 0V GND VO3+ VIN3 VG3 VCC VCC CD MOTOR PWB-C +B +B R823 1K C812 0.01 C813 100/10 C850 220/10 C849 0.056 C855 100/10 10 9 8 2.2V 2.1V 4.3V 2.1V 2.5V 3.4V 0V 2.1V 2.1V 2.1V 2.1V 5V R824 47K 12 11 10 9 8 7 6 5 4 3 2 1 C842 47/10 R821 150 R822 33 4.1V Q801 KTA1266 GR 3.4V 6 5 4 3 2 1 – + – M NM802 SPINDLE MOTOR M NM801 SLED MOTOR PICKUP UNIT(308) CNP802 FO16 TR+ 15 TR14 FO+ 13 PD 12 VR 11 LD 10 GND 9 F 8 C 7 B 6 A 5 C 4 E 3 +5V 2 1 R80B 68K 2V 2.1V 2.2V 2.1V 2.1V 2.1V 2.1V 2.1V 2.1V 2.1V 1.7V 0V 2.1V C841 100/10 13 R825 82K 14 C845 15 100/10 16 C846 17 0.1 18 19 C847 20 0.1 21 C848 R826 2.7K 39P 22 23 R828 1.2K 24 R829 R827 C839 39K 2P 68K C863 470P 6 5 4 3 2 1 6 5 4 3 2 1 + SP+ SP– SP+ SL– PU-IN GND NSW801 PICKUP IN 811 7/10 +B CNS803 2 R863 2.2K C844 0.0068 CNP803 6.5V 0V PO1+ VO3- PO1- OPO GND VO2VO2+ VIN2 VG2 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0.8V 1V 3.2V 3.2V 2.1V IC804 MM1469XH FOCUS/TRACKING/ SPIN/SLED DRIVER C857 47/16 C858 0.01 L801 10µH +B C843 0.1 IC801 TA2109F SERVO PRE AMP. R80E 82K CNW3 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 FO- FO– TR+ TR– TR+ TR- FO+ PD VR LD GND F C B A C E +5V PO+ ACTUATOR 1/2VCC 1/2V R80A R80C 82K 82K R80F 82K +B + - B + - A + - E VREF R80G 68K F C GND +B MON VCC 7 8 9 10 Figure 29 SCHEMATIC DIAGRAM (4/10) – 29 – 11 LD 12 + + - XL-3000V A T302 AM Tracking C343 33P C362 3.3/50 C329 0.022 D301 1N4148 VR351 10K(B) VD301 SVC348S C332 0.022 C331 0.047 C330 12P(CH) C302 0.001 R358 8.2K FM Mute Level B L353 1mH +B 1.5V 0V 5.2V 4.4V 3.8V 5 6 7 8 C351 0.022 3.6V 0V R308 10K 2.3V 0.8V 0V +B R382 330 R305 680 C315 100P R386 330 TP301 C316 10/16 C317 0.022 R315 33 R313 680 R304 47K C309 0.001 C308 0.022 D306 1N4148 C314 22P (CH) R314 C310 33 0.022 C311 10P(CH) C307 0.0047 C305 0.0047 FM 75ohms C312 33P 2 CF302 0.8V AM GND R312 2.2K Q306 2SC535 C R301 22 R316 330 CF303 1 3 3 2 C313 6P(UJ) R303 33K L303 FM OSC. Q302 2SC535 C D305 1N4148 E C306 7P(UJ) FM RF R307 47 Coverage L302 FM ANT. R302 100K C303 0.001 C304 0.01 FM IF T304 1 9 R306 10 VD302 KDV147C C318 5P SO301 ANTENNA TERMINAL 2 C381 12P(CH) F R310 4.7K X352 4.5MHz R309 470 C301 0.012 CHASSIS GND 2 C352 10/16 5.2V 4 1 5.2V 1.5V 3 FM Band 3 2 VD303 KDV147C 2 1 1 C319 18P(CH) BF301 BAND PASS FILTER D 0.8V IC301 TA7358AP FM FRONT END 24 23 2.1V R351 5.6K C337 0.022 AM Band Coverage 5V T306 C 5V 2.5V R336 5.6K FM IF AM OSC OUT IN AM MIX OUT AM OSC IN R323 68K IC303 LA1832S FM IF DET./ FM MPX./AM IF D302 1N4148 C334 27P(UJ) C335 560P C382 15P(CH) C349 0.001 C384 0.001 G +B H • NOTES ON SCHEMATIC DIAGRAM can be found on page 19. 1 2 3 4 Figure 30 SCHEMATIC DIAGRAM (5/10) – 30 – 5 6 IC LC PLL R374 1K 4 1 IC302 LC72131 PLL(TUNER) 7 3 4 5 6 7 8 C386 330P L351 100µH R387 5.6K R393 1K 9 10 11 C383 0.022 R395 47K R376 10K C355 22P C356 0.001 C370 1/50 C357 2.2/50 R355 3.3K 3.8V (1.9V) C358 1/50 3.8V (1.2V) 4V (2.2V) MPX IN R-CH OUT L-CH OUT PHASE (AM/FM) MO/ST 1.3V 13 1.3V 2.1V 15 14 IF OUT VCC 2.3V (0V) 16 MPX VCO FM DET STEREO 17 PHASE 9 C365 0.022 C363 0.022 C362 3.3/50 C369 56P C368 R356 1/50 1K X351 456kHz C371 R361 1/50 5.6K 10 11 12 +B R377 5.6K 14 13 12 9 4.7V (0V) 2 R391 390 R383 5.6K R384 6.8K C391 47/16 17 16 15 0V 2 C399 0.022 8 R365 10K IF REQ IF IN 8 MO/ST CF352 C385 0.01 5V 7 FM +B 2.9V R353 (4.3V) 270 5V C398 100/10 0V SD 0V (0.9V) 2.3V 18 0V 18 CF351 5V 6 0V (2.6V) C353 0.022 C354 0.022 AM LOW CUT FM/AM OUT 0.6V 2.1V (2.7V) C367 1/50 AM IN C387 0.022 AM IF IN GND VSM AM RF IN 2.1V (2.7V) 5V R350 2.7K 3.5V (0V) 19 2.6V (0V) R379 2.2K 3 5.2V 0.9V 5 VDD MUTE FM IN FM 22 21 20 PD 1 0V 4 3.7V (0V) 3.9V DO C380 10/16 T351 AM IF 19 1.7V (11.4V) 0.9V 3 AIN R352 1K 2.1V FM AFC 20 5.1V C392 0.001 C394 47/16 C350 0.022 4.8V CL 2 DI 86 0 R381 10K 21 0.1V 0V 2.1V 22 CE 1 0.1V 2.6V AOUT C397 0.022 82 0 0V OUT IN AM MIX OUT AM OSC IN REG 23 R373 1K R372 1K R371 1K CH) VSS 2 Hz 0V CH) X IN X OUT 5V 2 2.6V C352 10/16 R363 3.3K R364 3.3K C373 0.018 R357 470K C374 0.018 C366 0.001 C364 10/16 C360 0.022 C361 0.022 XL-3000V TUNER PWB-A2 AM SIGNAL FM SIGNAL Q351 KRC104 M 1 0V 3.7V (0V) 3 C372 R362 1/50 5.6K +B R366 2.2K ZD351 DZ5.1BSB FM ST SD DO L352 100µH C396 100/10 C395 0.022 +B R392 390 C393 R380 1/50 1.5K Figure 31 SCHEMATIC DIAGRAM (6/10) – 31 – 10 11 10 11 CE CL DI D_GND A_12V TUN_R TUN_L A_GND 9 8 7 6 5 TO MAIN PWB-A1(1/2) CNP307 P26 5,6-A 4 3 2 CNS307 1 Q360 KTA1266 GR +B 11.7V 10.8V 10.9V +B R385 5.6K R359 1.8K R360 4.7K D308 1N4148 12 XL-3000V DISPLAY PWB-A3 A SW727 FUNCTION SW726 REW PRESET DOWN R706 3.9K 1 2 3 4 5 6 7 8 9 10 11 12 13 14 SW718 VOLUME DOWN 2.47V 0V 7 5V 8 2.49V 9 2.47V 10 0V 11 2.24V 12 2.47V 13 C703 0.1 R702 10K X701 8MHz 24V C701 22P(CH) SW710 CD LID OPEN/CLOSE LMP701 R795 47K 0V 14 (CH) GND C702 22P 32.768kHz X702 5V 0V R731 1K 5V R732 1K 5V R733 1K 1 2 2 3 3 2 5V 2.5V 2.5V 2.5V SEG9 SEG8 SEG7 SEG6 XO MMOD SYSTEM 15 VREF– 16 CLID_SW DO 4.9V 22 0V 23 VSM 4.9V 24 VREF+ 0V 25 DI USWD_5R6V +B 4 D723 1N4148 +B +B 5V 0.4V 5V 4.2V R796 1K G Q707 KTA1266 GR 24.5V 24.5V R792 47K +B 23.7V RX701 REMOTE SENSOR 1 R7A1 1K 5V R7A3 100 C715 100/10 R7A4 120 Q703 KTC3199 GR R7A8 82 Q708 KTA1266 GR 0.4V 1.1V C714 560P 2 3 C713 10/16 1 0V +B R7B0 10K ZD701 DZ3.3BSB 2 0V 0.4V Q702 KTC3199 GR 0.4V C712 0.01 4.8V 3 C710 0.01 R7A7 1K Q701 KRC102 M R7A2 100K CNS652 R7A6 1K D721 1N4148 2 R7A0 1K R7A5 10K C711 3.3/50 D720 1N4148 1 R7A9 3.3K 5V R798 4.7K R778 47K Q709 KRC102 M R779 47K 3 2 4.5V R797 0.1V 2.2K 1 0V R780 47K R781 47K R783 33K +B R793 10K Q706 KRC102 M 3 2 0.1V 4.1V 1 0V C704 0.022 +B +B H • NOTES ON SCHEMATIC DIAGRAM can be found on page 19. 2 3 4 Figure 32 SCHEMATIC DIAGRAM (7/10) – 32 – 5 6 R765 0V R741 4.9V 1K 4.9V 5V R760 1K 0V R763 1K 0V R762 1K 4.9V R761 1K 4.9V R738 1K D_GND P_CONT +B 1 2.5V 2.5V 2.5V 2.5V SEG5 SEG4 SEG3 XI R744 1K 5V TO MAIN P26 5-H PWB-A1(1/2) CNP652 R782 1K R725 10K C705 0.01 D722 1N4148 F VSS 5V 26 27 28 29 30 31 32 33 34 35 L702 2.2µH 1K R799 1 +B OSC1 17 KEY1 5V 18 KEY2 5V 19 MODEL 0V 20 CLID_PRO 0V 21 MOT_DEC CFW701A CNW707 CNS707 P26 1-F TO CNP707 POWER PWB-B E R722 10K R721 10K 3 2 1 CLID_PRO R735 1K OSC2 R740 1K 0V 3 2 1 R734 1K VDD R739 1K D CFW701B VLC1 CLID_OUT SW709 ON/ STAND-BY 3.25V +B R728 1K CE R723 47K 5 VLC3 6 VLC2 RESET LAMP PWB-A7 1.7V 4 COM0 BUSY R729 47K +B 3 COM1 ACK R727 47K C 2 COM2 2.47V R720B 1.2K VD_DI R720A SW711 1.2K FF PRESET UP R711 1.2K 100 99 98 97 96 95 94 93 92 91 1 COM3 VD_DO SW721 MEMORY/SET R719 1.2K 2.47V SW712 CD PLAY/ PAUSE TUNING UP R710 2.7K 2.47V SW722 BASS/TREBLE 2.5V R708 2.2K 2.5V SEG0 2.5V B R718 1.5K SW713 VOLUME UP SEG1 SEG2 R707 2.7K CL SW725 CD STOP TUNING DOWN XL-3000V LCD701 LCD DISPLAY 75 SEG26 74 SEG27 73 SEG28 72 SEG29 71 SEG30 70 SEG31 69 SEG32 68 SEG33 67 66 65 64 63 62 61 CD_STB 60 CD_RES 59 PU–IN 58 CLID_DW 57 CLID_UP 56 FAN 55 DIMMER 54 SD 52 0V 0V R777 1K 4.9V R758 1K 4.8V R759 1K 4.8V 2.5V 2.5V 2.5V 2.5V 2.5V 4.9V 5V CNW702 CLID_DW 1 CLID_UP 2 CLID_PRO 3 CLID_SW 4 FAN 5 CD_STB 6 AMP_DEC 7 LIGHT 8 DIMMER 9 FAN_DEC 10 5V 5V 5V 5V R766 1K CD_STB 0V R769 1K CLID_DW 4.9V R770 1K CLID_UP 4.9V 4.9V 4.9V 0V 4.72V R772 1K 4.76V R773 1K CNS702 10 9 8 7 6 5 4 3 2 1 R771 1K 4.8V AMP_DEC R768 1K 4.8V 51 B-LIGHT R785 1K CNS704 1 VD_DI VD_DO ACK BUSY CLID_OUT GND STB STB 1 2 2 3 3 4 4 5 5 6 6 7 7 CNW704 P_CONT CNS703 SD SD STEREO STEREO DO CL +B CLID_OUT CE BUSY DI CD+B CD+B +B P_MUTE P_MUTE P_STB P_STB ACK A_24V VD_DI D_GND VD_DO SURROUND 5V CE CL 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 13 CNW703A DO DI +B CLID_SW B-LIGHT SURROUND +B 7 8 9 10 Figure 33 SCHEMATIC DIAGRAM (8/10) – 33 – 11 12 TO CNP703 MAIN PWB-A1(1/2) P26,27 6,7,8-A R757 1K 4.8V 4.9V R755 1K 4.8V R742 1K 4.8V 5V R764 1K 4.9V R751 1K 4.9V 5V R750 1K 0V 5V R765 1KR749 1K 0V R741 4.9V 1K 4.9V 5V R760 1K 0V 0 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 R763 1K 53 2.5V R776 1K STEREO P–CONT CD+B P–MUTE P–STB SURR LIGHT STB REMOCON SYS_STOP POWER CLID_OUT CE RESET ACK BUSY IC701 IX0038SJ SYSTEM MICROCOMPUTER/ FL DRIVER 2.5V TO CNP702 MAIN PWB-A1(2/2) P28 1-B,C SEG25 TO CNP804V VIDEO PWB-D P35 12-C SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 6 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 2.5V 2.5V SEG24 2.5V 2.5V SEG23 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 XL-3000V VIDEO PWB-D A Q11V 2SD1858 R2 +B +B 5V C105V 0.1 C125V 100/10 4.5V 3.8V C126V 0.1 R143V 220 R5V 4.7K B 1 2 3 4 5 6 7 8 9 3.4V 1.6V 1.6V 1.8V 1.8V 1.9V 1.9V 1.9V 2.0V 1.9V C 1.7V 1.2V 1.3V C122V 0.1 1.6V 0V 10 11 12 13 14 15 16 C112V 0.1 5V C115V 5V 22/25 VCC 32 5V 31 PGM/A18 VPP A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 D0 D1 D2 VSS A17 A14 A13 A8 A9 A11 OE A10 CE D7 D6 D5 D4 D3 R91V 4.7K 3.2V 30 29 28 27 26 25 24 23 22 21 20 19 18 17 +B R98V 4.7K R93V 4.7K 2.0V 1.3V 1.7V 1.6V +B 1.6V 0V 1.9V 0.3V 1.2V 1.5V 1.4V 1.4V 1.4V 0V 5V R157V 820 2.6V 0V 3.0V C110V 0.1 0V 2.6V 2.7V 3.5V 3.3V 1.2V 1.3V 1.6V 1.4V 1.4V 1.4V 1.5V 3.5V 1.2V 0V 0.3V 3.5V 3.5V 1.7V 1.9V 2.0V 1.9V 1.9V 1.9V 1.8V 1.8V 1.7V 1.6V VSS LA11 LA10 LA9 LA8 LA7 LA6 LA5 LA4 LA3 LA2 LA1 LA0 LSCE0 LSCE1 LROMCE LOE LWR LD7 LD6 LD5 LD4 LD3 LD2 LD1 LD0 AUX7/STB AUX5 DSC_STB AUX6/SCK VCC3 IC15V ES3880F VIDEO CD DECODER R164V 10 R165V 10 5V 0V 2.4V 0.9V 2.4V 2.4V 0.4V 0.9V 2.9V 1.3V 2.2V 1.5V 2.8V 2.7V 0.4V 0.5V 2.9V 1.8V 1.3V 1.7V 1.8V 1.8V 1.8V 1.4V 1.8V 1.7V 1.8V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 3.6V 0V VSS 50 0.2V AUX4 49 5V VD_DI 48 0.2V VD_DO AUX2/VD_DO 47 AUX1/DSADATA 46 5V 5V AUX0/DSAACK 45 2.3V PCLKQSCN 44 2.2V PCLK2XSCN 43 0.2V DCLK 42 4.5V HSYNC 41 4.8V VSYNC 40 1.0V YUV7 39 1.2V YUV6 38 1.9V YUV5 37 1.9V YUV4 36 2.3V YUV3 35 0.6V YUV2 34 0.6V YUV1 33 1.8V YUV0 32 VCC3 31 3.6V 48 AUX3/VD_DI R160V 4.7K R159V 820 R158V 820 3.5V 3.5V R169V 33 3.5V R170V 4.7K 3.4V 3.2V R161V 33 MCLK1.5V TSD0.1V R168V TBCK1.8V 33 TWS2.1V 0.1V R156V 4.7K 0V VCC LA12 LA13 LA14 LA15 LA16 LA17 AUDIOCLK AUDATA BCLK LR DRAS1/DOE RSD RBCLK RWS TDMCLK TDMDR TDMFS DCAS VSS C121V 22/25 1.6V R166V 33 R163V 33 C120V 0.1 2.0V 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 VCC3 DRAS DWE DA0 DA1 DA2 DA3 DA4 DA5 DA6 DA7 DA8 DBUS0 DBUS1 DBUS2 DBUS3 DBUS4 DBUS5 DBUS6 DBUS7 DBUS8 DBUS9 DBUS10 DBUS11 DBUS12 DBUS13 DBUS14 DBUS15 RESET VSS 1.6V 1.3V E C119V 0.1 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 5V +B 1.9V 0V C109V 100/10 C108V 0.1 D 1.6V IC10V IX0041SJ ROM 256Kx16 TO CHASSIS GND F R97V 4.7K +B +B C116V 0.1 +B 5V 1.3V 2.9V 0.5V 0.4V 5V 2.7V 2.8V 1.5V 2.2V 3.5V 3.5V 1.8V 1.7V 1.8V 1.4V +B 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C117V 0.1 VCC A3 A2 A1 A0 NC RAS WE NC NC D7 D6 D5 D4 VCC D3 D2 D1 D0 VCC C102V 22/25 VSS A4 A5 A6 A7 A8 OE UCAS LCAS NC D8 D9 D10 D11 VSS D12 D13 D14 D15 VSS C111V 0.1 R162V 4.7K 5V +B 0V 2.4V 0.9V 2.4V 2.9V 0.4V 0.4V 0V 2.9V 1.3V 3.3V 3.3V 0.1V 1.8V 1.7V 1.8V 1.8V 0V 1.8V 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 C118V 22/25 AUX0 G IC16V IX0025SJ D-RAM 256Kx16 R08A 4.7K R12AV 4.7K H • NOTES ON SCHEMATIC DIAGRAM can be found on page 19. • The numbers 16 and 17 are waveform numbers shown in page 41. 1 2 3 4 Figure 34 SCHEMATIC DIAGRAM (9/10) – 34 – 5 6 VDAC Q12V 2SC1740 SR 2.9V R112V 56 3.6V R124V 220 R114V 6.8K C104V 100/10 5.7V 1 2 3 4 5 6 7 C169V 0.1 C161V 100/10 C158V 100/10 0V 1.3V 5V 2.3V 0V 0V 0V 5V 0V 5V 0V +B C160V 0.1 R194V 270 C124V 0.1 C150V 0.1 0V 5V 2.4V 0V 5V 2.3V 0V 0.8V +B 2V TC100V 10P C129V 27P(CH) 0V 5V 2.3V 2.2V L104V 3.3µH C136V 0.1 C184V 0.1 BUSY VD_DI VD_DO ACK STB DGND CLID_OUT CNP804V R171V 100K X1V 27MHz R137V 1K R138V 33 R140V 1K R141V 1K L103V 3.3µH +B R178V 82 R167V 33 C168V 22P(CH) C137V 10/25 R139V 1K C183V 22P(CH) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 81 82 83 4.8V 84 1.4V 85 1.0V 86 1.2V 87 1.9V 88 1.9V 89 5V 90 0V 91 2.3V 92 1.4V 93 0.6V 94 1.4V 95 0.8V 96 1.6V 97 0.8V 98 1.3V 99 0V 100 C127V 0.1 HSYN_B DSC_D6 VSYN_B DSC_D5 YUV7 YUV6 YUV5 YUV4 VCC VSS YUV3 DSC_D4 YUV2 DSC_D3 YUV1 DSC_D2 YUV0 DSC_D1 VSS MIC2 MIC1 AOL+ AOL– AOR– AOR+ VCCA VREFP VCM VSSA BUSY/AUX15 S_EN/AUX14 LA18/AUX13 RBCK NC/AUX12 NC/AUX11 NC/AUX10 RSD VCC VSS DSC_D7 IC14V ES3883F VIDEO CD ENCODER 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 2.3V 2.3V 2.3V 2.3V 0V C162V 0.1 C164V 47/10 5V C165V 0.1 5V 0V 2.3V 0V 0V 5V R105V 4.7K +B +B C166V 22/25 C159V 0.1 0V 0V 5V 5V 1.8V 0.1V 2.1V 1.5V C135V 0.1 5V 5V 0V 2.7V 5V 0V 0V 3.5V C106V 1 0V 1.2V 3.5V 5V 0V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 C130V 0.1 +B +B R06AV 4.7K R142V 33 R01AV 4.7K R100V 4.7K 0V R193V 4.7K R07AV 4.7K R10AV 4.7K R02AV 4.7K R03AV 4.7K CNP801V DGND 1 /RST 2 BUS0 3 BUS1 4 BUS2 5 BUS3 6 BUCK 7 /CCE 8 PU_IN 9 LRCK 10 BCK 11 DATA R11AV 4.7K EAUX0 EAUX01 EAUX02 EAUX03 EAUX08 EAUX04 R08AV 4.7K R09AV 4.7K CNS801 TO P28 1-D,E MAIN PWB-A1(2/2) 1.5V 4.5V PAL R94BV (LOGO) 0 1.2V VSS NC NC NC VCC DSC_CLK AUX0 DSC_D0 AUX1 DSC_STB AUX2 NC RESET_B AUX7 NC VCC MCLK AUX8 TWS AUX9 TSD TBCK RWS RSTOUT VSS VSS SQCK SQSO NC NC R164V 10 R165V 10 PCLK2X PCLK VCC VSS NC VSS XIN VCC VSS XOUT AUX3 AUX4 AUX5 AUX6 VCC ACAP VDAC VSSAV VSSAV YDAC VCCA VCCA CDAC VSSAV VSSAV COMP RSET VREFM VREF VSSAA 27MHz NTSC R94AV (LOGO) 4.7K R163V 33 2AV .7K C167V 22P(CH) R102V 100K R190V 10K R188V 10K C147V 100/10 C139V 10/25 R111V 2.2K +B 1 2 3 4 5 6 7 8 C138V 10/25 +B C131V 0.001(CH) L11V 10µH CNS802 1 2 3 4 5 6 7 8 9 CNW802V R195V 100 C101V 1000/6.3 VDAC AGNDV L-CH AGNDA R-CH +5V DGND +12V C140V 10/25 +B R113V 100 R116V 15K CNS704 FROM P33 12-E DISPLAY PWB-A3 C103V 22/25 C172V 10/25 R103V 6.8K R121V 3.3K C148V 100/10 R181V R183V 100K C149V 100K 0.1 C141V 33P (CH) R187V 10K R123V 75 +B R189V 10K +B R115V 15K C142V 33P(CH) –+ 6 5.3V 5 R185V 8 10.9V 10K 5.3V C171V 10/25 R101V 100K 33P(CH) 1 6.1V R108V +– 10K 5.3V 2 5.3V 3 4 R186V 0V 10K R184V 100K R107V 10K C143V 33P 6.1V 7 (CH) R182V 100K VIDEO SIGNAL CD SIGNAL +B IC11V NJM4565M 17 BUFFER AMP. C144V R104V 10K 16 CNP802A TO MAIN PWB-A1(1/2) P26 4-A XL-3000V 1 CNW801 12 12 7 8 9 10 Figure 35 SCHEMATIC DIAGRAM (10/10) – 35 – 11 12 XL-3000V TERMINAL PWB-A4 A C412 SO401 R408 LEFT CNP810 R406 VIDEO/ AUX IN B CFW452 D412 D411 L402 C851 L802 C853 WH 1 2 3 4 5 C660 C630 F653 T1.6A L 250V D657 C657 D901 C658 D658 C901 C651 C126 12 GY C614 R638 CNP801 C659 D660 CFW852 TO CHASSIS GND LUG(205) L602 RIGHT TO CHASSIS GND LUG(205) CNS805 WH 3 2 1 RD 3 2 1 CNP805 C852 J801 DIGTAL OUT CNS608 2 1 CNP608 2 1 3 2 1 L601 C615 FROM POWER TRANSFORMER P38 4-C,D D659 C414 C613 LEFT R637 GY BK CNS607 WH 3 2 1 RD 3 2 1 CNP607 VIDEO OUT C BK RD 2 1 2 1 2 2 1 1 CNP807 CNS807 R407 L401 R405 C411 RIGHT SO601 SPEAKER TERMINAL M802 FAN MOTOR TO CHASSIS GND LUG(205) CFW451 C413 CHASSIS GND C616 C654 T D902 D C902 C640 CHASSIS GND C125 C639 LUG (205) C101 R104 R115 R103 C104 16 14 12 10 8 6 4 2 15 13 11 9 7 5 3 1 D651 D653 R105 C109 R101 R661 R662 R111 D652 L603 R873 CNP802 1 Q908 2 D654 C103 3 C105 PK Q601 R102 PINK E C B R108 R123 E C B B C E Q103 Q101 R119 G B E E C B C E Q104 R120 C GY GY BK CNW602 3 2 1 GY GY BK 3 2 1 B C E C120 R609 3 2 1 C602 IC682 R121 R122 E C B Q602 R124 CNP601 1 2 3 R864 R118 1 2 3 E B R613 R607 R610 R614 Q607 C102 C601 Q102 C621 C626 R612 R80C R628 1 1 C 2 B C906 R912 C905 3 4 ZD902 5 6 D603 CNP652 7 2 1 C629 8 D604 C603 E 2 R R621 D605 C627 1 2 3 Q608 1 2 C628 3 Q609 R634 D803 D804 1 2 3 4 5 6 7 8 9 10 R865 CNW601 CNP FROM DISPLAY CNS652 PWB-A3 P39 10-A FROM CNS802 VIDEO PWB-D P40 1-A,B 5 CNS307 TO TU PWB P38,39 6,7-A H • The numbers 1 to 15 are waveform numbers shown in page 41. 1 2 3 C83 R829 C843 C849 Q606 C CNP602 Q610 B B C E R110 R902 R827 W R80F R80E BLACK R619 R629 R80A BK Q603 Q903 CNW608 GRAY WHITE C620 D602 E C B CNP802A GY WH (W) B C E ZD601 VIOLET 3 R90 B C R901 R617 VL Q901 2 R821 R913 BLUE 1 C904 ZD602 BL CHASSIS GND C622 GREEN R624 GR R620 C625 YELLOW R611 YL C110 Q604 ORANGE R603 RED OR Q904 ZD901 R608 R D (R ) B C E R911 1 2 C113 3 R109 4 5 6 C112 7 C116 8 9 R114 10 11 C114 C108 12 13 14 R106 15 C106 R604 F BROWN R910 C624 R623 IC601 COLOR TABLE BR C903 C107 C111 R113 Q605 E R905 J601 HEAD PHONES 4 Figure 36 WIRING SIDE OF P.W.BOARD (1/5) – 36 – 5 6 XL-3000V CNS804 1 BK 2 RD CNW804 MAIN PWB-A1 RED R217 C403 C425 Q805 C430 E C B C651 R866 L801 R80B R80G 12 C817 C824 C821 C818 R425 R424 1 C870 R823 C842 C819 B C E Q801 R861 6 CNW803 R824 C841 WH GY GY GY GY GY L803 B C E CD MOTOR PWB-C 4 L806 Q861 C811 1 2 3 4 5 6 CNS803 14 C858 1 14 10 R862 5 IC804 20 PICKUP UNIT(308) 25 R863 3 2 7 8 2 CNW3 R914 LED PWB-A6 1 1 D801 CNW701 1 1 2 3 4 5 6 7 8 9 10 11 CNP307 1 16 CNS701 1 WH BK 2 7 8 10 9 6 16 28 15 D606 CNS307 TO TUNER PWB-A2 P38,39 6,7-A CNP803 1 23 45 6 R843 X801 R814 F3895AF R855 C862 R820 C823 R810 NSW801 PICKUP IN CNW801 FROM DISPLAY PWB-A3 CNS702 P39 10-F NM801 SLED MOTOR R819 C826 C860 IC801 NM802 SPINDLE MOTOR 13 C840 R813 C822 55 C859 C843 C849 R80A 1 C845 C847 R80C R80F R80E R827 R826 R828 C844 C846 C839 R825 13 24 R829 20 15 60 50 51 C864 C872 C807 10 45 R853 R852 C827 70 65 40 12 C867 C868 C869 C830 81 80 75 IC802 35 C804 R807 C813 C848 5 90 85 R811 R812 CNP701 C803 C850 C806 C855 5 95 20 R808 R809 R901 1 2 10 25 R804 3 C805 R902 FROM DISPLAY PWB-A3 CNS703 P39 10-B,C TO VIDEO PWB-D CNP801V P40 2-B,C C835 R832 C866 C828 15 R802 R806 30 Q902 31 C801 C802 C812 B C E Q901 2 1 C838 1 C863 R801 3 1 CNW805 C820 C809 R874 R905 Q907 Q807 R836 R833 R834 R835 C837 C836 1100 WH R851 C871 RD C829 E C 3 R904 B IC805 Q802 C810 R879 1 2 3 B C E R822 E C B 1 Q908 2 R882 CNS801 12 10 8 6 4 2 11 9 7 5 3 1 1 2 3 4 5 6 7 8 9 10 R837 R877 R876 D802 1 3 2 1 2 R830 R887 CNP806 CNP804 R831 C865 9 8 7 6 5 4 3 2 1 Q803 R873 1 R880 B C E CNP703 CNP702 2 2 GY GY BK 1 02 2 1 R868 1 CNW806 3 2 1 CNS806 R423 13 12 11 10 9 8 7 6 5 4 3 2 1 C857 C654 Q804 R867 R870 F651 T3.15A L 250V 3 C419 30 C431 Q806 B C E ASSIS GND C892 C893 D403 D402 D401 C429 C420 25 R881 C421 C423 R439 C901 16 R421 C417 20 R415 R417 C657 D901 5 R884 F652 T3.15A L 250V 10 IC401 R404 SW802 CD LID OPEN/CLOSE R207 C433 Q203 C432 1 R885 R883 R888 C404 R403 C415 R212 3 2 1 C422 R422 C426 15 R418 C402 R416 R854 C660 C407 SWITCH PWB-A5 8 7 6 5 R216 R214 C424 R401 C825 D659 C408 WH 3 CNW607 1 2 3 4 5 C401 MER D R440 D201 CNW807 GY BK D805 R402 1 R210 IC201 S G D C216 C418 R438 C416 1 2 3 4 R215 Q201 R218 C204 R209 C212 C211 R206 R203 RD CNP801 R213 R211 R205 C213 C203 C214 R201 R204 R202 R437 C202 R208 C201 C209 M801 CD LID OPEN/CLOSE MOTOR C215 C887 C208 1 16 11 15 9 10 Figure 37 WIRING SIDE OF P.W.BOARD (2/5) – 37 – 11 12 XL-3000V R377 R366 C373 C371 C374 R362 C372 R357 C364 R364 R363 R393 C363 C366 C369 Q306 R361 R383 R395 L352 R376 C354 X351 C353 C356 C352 C351 3 2 1 C358 Q351 C368 T306 R355 R350 C329 C386 C385 R310 CF303 C335 VD301 D302 R336 R314 R312 C310 C349 L302 C357 C367 CHASSIS GND C C302 D301 C365 D306 IC303 C396 ZD351 C355 CF302 R352 R353 C399 1 2 3 1 2 3 4 5 6 7 8 9 10 1112 R313 R351 B C360 C C350 C361 E 24 23 22 21 20 19 18 17 16 15 14 13 R358 C319 R385 R384 C398 CF351 C362 3 VR351 R303 1 2 3 R307 R302 C307 VD303 C303 C332 C306 CF352 1 2 3 C308 C309 C395 C370 T351 C343 2 VD302 R308 C313 C391 R391 R392 R382 L353 R309 L303 C330 C331 C334 R323 BF301 1 R316 C383 AM E C B R386 R387 L351 C314 Q360 D308 C384 IC302 9 8 7 6 5 4 3 C305 2 1 D305 R305 C317 B Q302 C R304 E R315 C304 R373 R372 R371 R301 R306 C312 C393 C315 C316 GND C311 B C301 IC301 C318 FM 75 OHMS CNS307 1 2 3 4 5 6 7 8 9 1011 X352 R374 1 2 3 4 5 6 7 8 9 10 11 T304 SO301 ANTENNA TERMINAL CNP307 TO PW P36,37 6,7-G C337 TP301 22 21 C397 R379 20 C380 19 C392 18 R365 17 C394 R380 16 15 C387 14 13 R381 12 R359 R360 C381 A C382 TUNER PWB-A2 R356 T302 YL BK YL BR BR 5 4 3 2 1 TO MAIN PWB-A1 CNP801 P36,37 6,7-B,C D T651 POWER TRANSFORMER (MAIN) F654 T.F 2A,250V 7 BK WH 5 3 1 BK POWER PWB-B AC POWER SUPPLY CORD RD 9 RD BL AC110/127/220/ 230~240V, 50/60Hz RD E 1 2 RLY601 F 9 7 5 3 SW651 VOLTAGE SELECTOR D689 1 D685 CNP651 R685 220V 1 2 B C E Q683 CNP653 230~240V E C B Q681 D6 R686 G 127V C683 110V SO655 AC POWER INPUT SOCKET AC110/127/220/ 230~240V, 50/60Hz T681 POWER TRANSFORMER (SUB) H 1 2 3 4 Figure 38 WIRING SIDE OF P.W.BOARD (3/5) – 38 – 5 6 XL-3000V LMP701 1 TO MAIN PWB-A1 CFW701B CNP307 TO MAIN PWB-A1 P36,37 6,7-G CNP652 P36 5-F 3 LAMP PWB-A7 3 4 5 6 7 8 9 1011 CNS652 R764 SW709 ON/STAND-BY 26 7 CNW704 25 R768 BROWN BK BLACK PK PINK CNW653 TO MAIN PWB-A1 1 2 CNP702 P37 8-D 89 85 CNS702 1 2 3 4 5 6 7 8 9 10 R785 R7A4 C711 R7A1 R7B0 R7A2 D721 3 2 1 SW710 D681 C704 Q701 R7A9 D688 C688 C683 E C B Q702 R7A8 C712 C710 D720 C689 R687 IC681 R686 3 2 1 R7A7 R7A6 R688 R7A5 C715 R689 R7A0 E C B ZD683 CNP707 D684 SW712 CD PLAY/PAUSE TUNING UP R707 R720A CD LID OPEN/CLOSE D683 D682 DISPLAY PWB-A3 7 8 9 10 Figure 39 WIRING SIDE OF P.W.BOARD (4/5) – 39 – 11 12 BASS/ TREBLE R711 SW722 R706 R710 R783 1 Q703 R735 R731 ZD701 D723 D686 2 D722 Q681 3 C665 CNP653 E C B 4 ZD684 1 2 B C E R766 1 R685 683 MEMORY/ SET 10 BK GY GY GY GY GY GY GY GY GY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 LCD701 FL DISPLAY WHITE L702 GRAY W H( W ) SW726 REW PRESET DOWN VIOLET SW711 FF PRESET UP VL GY R772 R795 BLUE 76 75 R769 GREEN BL 85 70 80 SW725 CD STOP TUNING DOWN YELLOW 90 65 R770 YL GR 1 100 95 R773 ORANGE 55 R771 RED OR 5 IC701 60 CNW702 BK RD F654 T.F 2A,250V R702 15 10 45 R744 R750 BR R723 R727 R729 30 20 35 50 51 RD( R) R7A3 R782 40 COLOR TABLE X702 R725 R728 X701 R777 RX701 REMOTE SENSOR C703 C701 1 R776 R734 R733 R732 C702 1 VOLUME DOWN 1 2 3 R722 R741 C713 R761 VOLUME R719 UP R721 R749 SW721 R718 C714 R739 R720B SW713 R778 R755 R742 R757 R758 R751 SW727 FUNCTION Q709 R798 R797 R793 CFW701A SW718 R781 R738 BK GY GY GY GY GY GY 3 R779 R780 R759 CNP804V P40 4,5-C 1 2 3 4 5 6 7 CNS704 13 R708 E C B Q708 R762 TO VIDEO PWB-D GY GY GY GY GY GY GY GY GY GY GY GY BK R792 Q707 1 R760 CNP703 P37 8,9-D B C E 3 R740 C373 1 CNS703 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 R765 R763 TO MAIN PWB-A1 WH BK BK WH CNW703A 1 2 3 4 Q706 3 2 1 R796 CNS707 R799 CNW707 2 1 XL-3000V 17 16 C141V R181V R185V R186V 1 CNW801 1 TO MAIN PWB-A1 CNS801 P37 9-D R08AV R12AV 12 12 11 10 9 8 7 6 5 4 3 2 1 25 C 20 15 10 IC14V 90 45 C164V 55 50 51 C150V 60 65 70 10 100 5 C184V C136V L104V C161V 85 55 50 R161V 60 65 70 75 TC100V 80 L11V CNP804V C 7 6 5 4 3 2 31 3 30 4 29 5 28 6 27 26 8 IC10V 9 25 24 10 23 11 22 12 21 13 20 14 19 15 18 17 R143V C105V 1 R91V B R5V R124V C131V 32 2 16 Q12V C104V C109V C103V E C125V R123V R121V X1V R112V R111V R170V 81 C108V C183V R171V R178V IC15V 81 80 R194V R159V 45 R167V R156V R160V R169V R168V R166V R158V 90 51 75 C124V C158V C127V 85 C169V L103V 15 1 7 C110V 95 40 R165V R164V R163V 95 40 C160V 20 25 100 5 35 R100V R94AV C162V 31 35 31 C165V 1 30 C120V R105V R09AV C121V 1 30 CNP801V R162V 20 C116V C159V C166V 15 C148V C147V C138V 10 5 R157V B C140V C112V R137V R102V C102V R13V8 1 IC16V R139V 2 R104V C149V C139V C137V C115V 8 1 C167V C168V R116V 21 C111V R140V 3 C143V C171V R182V 5 R189V 25 30 R141V 4 R115V R184V R103V R195V R187V 35 C117V C129V 5 R101V 40 C172V C130V R01AV 6 9 C118V C144V R142V R02AV R03AV TO MAIN PWB-A1 CNP802A P36 5-F GY GY GY GY GY GY GY GY IC11V C142V R183V 7 1 R11AV R10AV R07AV R06AV R94BV R193V C135V C106V 8 R190V R188V CNW802V CNS802 C122V R108V 4 R107V A VIDEO PWB-D (TOP VIEW) C126V R93V C101V R114V R113V E B C Q11V R97V R98V FROM DISPLAY CNS704 PWB-A3 P39 10-C,D D VIDEO PWB-D (BOTTOM VIEW) E Q11V C101V X1V E C B C104V C158V C125V C161V L104V L103V E Q12V TC100V 7 6 5 4 3 2 1 CNP804V L11V C103V 16 17 15 18 3 14 19 5 13 20 12 21 11 22 10 23 CNP801V F C109V 1 2 4 6 7 8 R5V B C C164V 9 10 11 12 9 C166V 1 8 C121V CNW802V G C137V C139V C140V C138V C147V C148V C171V 9 C102V C172V IC10V 26 6 27 5 28 4 29 3 30 2 31 1 32 C115V CHASSIS GND H • The numbers 16 and 17 are waveform numbers shown in page 41. 2 3 4 Figure 40 WIRING SIDE OF P.W.BOARD (5/5) – 40 – 5 25 7 C118V 1 24 6 XL-3000V WAVEFORMS OF CD CIRCUIT NO DISC FOCUS SEARCH 1 STOP 12 1 FOO FO+ 13 2 IC804 26pin 3 FO- SEL 5 6 11 2 15 3 FMO 6 1 FEI 3 TEI 1 TRO 2 IC802 46pin SBAD 11 2 IC802 49pin RFO 15 3 FMO 3 IC802 53pin IC801 22pin STOP PLAY REVIEW 6 1 FEI TEI 1 TRO 2 IC802 46pin IC802 43pin RFGO 11 2 IC801 19pin IC802 49pin RFRP 15 3 IC801 17pin 3 FMO IC802 53pin STOP TEI PLAY TCD-782 TNO-02 PLAYBACK 16 1 IC802 46pin TRO SBAD LO 1 RO 2 IC11V 7pin 2 IC802 49pin 7 2 CUE IC802 44pin 11 TRO PLAY IC802 43pin 6 1 IC802 53pin STOP 10 TEI IC802 49pin TEI 5 PLAY IC802 46pin IC802 46pin 5 3 STOP 1 FEI 6 DMO TOC IL IC802 43pin 9 2 IC802 55pin IC802 57pin 8 SBOK 14 3 FOCUS SEARCH 7 1 IC802 12pin IC804 27pin 4 TMAX IC802 30pin IC802 48pin 2 PLAY 17 IC11V 1pin 3 IC802 44pin – 41 – XL-3000V TROUBLESHOOTING When the CD does not function When the CD section does not operate when the objective lens of the optical pickup is dirty, this section may not operate. Clean the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check the following items. Remove the cabinet and follow the troubleshooting instructions. "Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below." Turn off the power, and wipe the lens softly using a cleaning paper moistened with commercially available cleaning solution so as not to damage it. Be careful not to touch the lens with bare hands. Dust gradually accumulates on the objective lens during use, and it may degrade performance. To avoid this problem, use a cleaning disc designed for CD optical pickup lenses. HOW TO USE 1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has the mark next to it. 2. Place the CD cleaner disc onto the CD disc tray with the brush side down, then press the play button. 3. You will hear music for about 20 seconds and the CD player will automatically stop. If it continues to turn, press the stop button. CAUTION The CD lens cleaner should be effective for 30 - 50 operations, however if the brushes become worn out earlier then please replace the cleaner disc. If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth. Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the event of this happening then drink and / or rinse with clean water and seek medical advice. The CD cleaner disc must not be used on car CD player or on computer CD ROM drives. All rights reserved. Unauthorized duplicating, broadcasting and renting product is prohibited by law. Cleaner Liquid Cleaning Disc PARTS CODE: UDSKA0004AFZZ – 42 – XL-3000V Make sure that the disc is normal, and set the CD TEST MODE (STEP 1). Is the measured voltage as specified in circuit diagram? Check the main unit power supply circuit. No Yes Is "Er-CD01" displayed"? No Yes Move the pickup to most internal circumference side of disc. Turn the power off and reset the CD TEST MODE (STEP 1). Is "PU ERROR " not displayed? No Check the pattern between pin 58 (PU_IN) of IC701 and CNW803/CNS803. Check the between CNW803/CNS803 and PU-IN switch. Yes Is +5V applied to pin 100 (/RST) of IC802? No Check the PWB pattern between pin 59 (CD_RES) of IC701 and pin 100 (/RST) of IC802. No Is CD Lid switch SW802 ON condition ? Yes Does the CD TEST MODE advance from "STEP 2"? Yes No Set ON condition the CD Lid switch. Yes Check the between pattern IC701 and SW802 If OK. Check the main unit power supply circuit. Does the laser come on in CD TEST MODE "STEP 2"? No Check the procedure in "LASER FAILURE". Yes Does the CD TEST MODE advance from "STEP 3" to "STEP 4"? Yes No Does the spindle motor rotate normally when the CD TEST MODE changes from "STEP 4" to "STEP 3"? No Check the procedure in "FOCUS FAILURE". Check the procedure in "SPINDLE MOTOR CLV SERVO FAILURE". Yes Is the HF output on pin 38 of IC802 in CD TEST MODE "STEP 5"? No Check the procedure "HF ERROR". Yes Does the sound heard when the optical pickup move to the selected play by the FF /REW key. No Does the sled motor move ? No Yes Check the procedure in "SLED MOTOR OPERATING FAILURE ". Yes Check the procedure "NO SOUND" Does the LCD track number and time indicator work properly ? No Check the pattern between IC701 and LCD701. Yes Turn the power off and then back on. Does the unit initialize properly and start playback when PLAY key is pressed? No Is "Er-CD01 " displayed ? No Check the procedure in "HF ERROR". Yes Yes Check the pattern between pin 58 (PU_IN) of IC701 and CNW803/CNS803. Check the between CNW803/ CNS803 and PU-IN switch. Does the unit play in order in the FF mode? No Check the procedure in "TRACK SEARCH FAILURE". Yes Does playback continue for 30 seconds after the start of playback ? No Yes Normal – 43 – Check the procedure in "SLED SERVO FAILURE". XL-3000V • Laser failure. Is +6.2V applied to the emitter of Q861 ? No Check the PWB pattern between emitter of Q607 and emitter of Q861. Yes Check the peripheral parts of IC804 and Q861. Is +5V applied to the collector of Q861 ? No Yes No Check the PWB pattern between collector of Q861 and pin 62 of IC802. No Check the PWB pattern between collector of Q861 and pin 1 of IC801. No Does the laser come on when pattern cut between pin 8 (SEL) of IC801 and pin 57 (SEL) of IC802 ? Is +5V applied to the pin 62 (VDD) of IC802 ? Yes Is +5V applied to the pin 1 (VCC) of IC801 ? Yes Is 0V applied to the pin 57 (SEL) of IC802 ? Yes Yes No Check the PWB pattern between IC701 and IC802 (BUCK/CCE/ BUS0~3) Is approx. 2V applied to the collector of Q801. No Check the peripheral parts of IC801 and Q801. If it is normal, the optical pickup is faulty. No Check as stated in item "FOCUS SERVO SAWTOOTH WAVE FAILURE". Yes Check CNP802/CNW3. If it is normal, the optical pickup is faulty. • Focus failure. Does the optical pickup move up and down when the disc is removed? Yes Is the following waveform output at the pin 43 (FEI) of IC802 when the disc is set? Check the periphery of IC801 and CNP802/CNW3. Is it normal? No Yes Yes pin 43 The optical pickup is faulty. (FEI) pin 48 (FOO) pin 44 (SBAD) Is the waveform shown above input at the pin 44 (SBAD) of IC802? No Yes IC801 is faulty. – 44 – Check the pattern between pin 13 of IC801 and pin 44 of IC802. Check the periphery of IC801 and CNP802/CNW3. XL-3000V • Focus servo sawtooth wave failure. Is sawtooth wave output to the pin 48 (FOO) of IC802 ? No IC802 is faulty. Yes 1.5~2.5sec Check the PWB pattern between emitter of Q607 and IC804. Is +6.2V applied to the pins 21 and 22 (VCC) of IC804 ? No Yes Is sawtooth wave obtained between pins 26 and 27 of IC804 ? No Yes Is +5V applied to the pin 7 (MUTE) of IC804 ? No Yes 1.5~2.5sec Check the PWB pattern between pin 7 of IC804 and pin 60 (CD STB) of IC701. Check the PWB pattern between pin 48 (FOO) of IC802 and pins 24 and 25 of IC804. If OK. IC804 is faulty. Is sawtooth wave obtained between pins 13 and 16 of CNP802/CNW3 ? (as shown above) Check the PWB pattern between CNP802/CNW3 and IC804. No Yes CNP802/CNW3 connection failure or optical pickup failure. • Spindle motor clv servo failure. Is following wave output to the pin 55 (DMO) of IC802 when the CD TEST MODE "STEP 3" is changed to " STEP 4" ? No Check the procedure in "HF ERROR". If OK. IC802 is faulty. No Check the PWB pattern between pin 55 (DMO) of IC802 and pins 9 and 10 of IC804. If OK. IC804 is faulty. Yes DMO Is above wave obtained between pins 11 and 12 of IC804 ? Yes Is above wave obtained between pins 9 and 12 of CNP802/ CNW3 ? Check the PWB pattern between CNP802/CNW3 and IC804. No Yes CNP802/CNW3 connection failure or optical pickup failure. – 45 – XL-3000V • HF error. Is output (tracking error signal) obtained at the pins 46 (TEI) and 47 (TEZI) of IC802 the CD TEST MODE "STEP 4" is changed to "STEP 5"? No Is output obtained at the pins 3 and No 8 of CNP802/CNW3. Optical pickup failure. Yes Yes test mode "step 4" Check the periphery of IC801. Check the PWB pattern between pin 12 (TEO) of IC801 and pins 46 and 47 of IC802. Is it normal ? test mode "step 5" TEI TEZI IC801 is faulty. No Yes Check the PWB pattern between pin 49 (TRO) of IC802 and pin 19 of IC804. Check the periphery of IC804 and CNP802/CNW3. If OK. Optical pickup failure. Is output (HF signal) obtained at the pin 38 (RFI) of IC802 when the CD TEST MODE "STEP 4" is changed to "STEP 5"? No Optical pickup failure. Yes Yes test mode "step 4" test mode "step 5" Check the periphery of IC801. Check the PWB pattern between pin 19 (RFGO) of IC801 and pin 38 (RFI) of IC802. If OK. IC801 is faulty RFI Is output (HF signal) obtained at the pins 41 (RFZI) and 42 (RFRP) of IC802 when the CD TEST MODE "STEP 4" is changed to "STEP 5"? Yes Is output obtained at the pins 4 and 5,6 of CNP802/CNW3. No test mode "step 4" No Check the periphery of IC801. Check the PWB pattern between pin17 (RFRP) of IC801 and pins 41 (RFZI) and 42 (RFRP) of IC802. If OK. IC801 is faulty. test mode "step 5" RFZI RFRP Is the following wave output to the pin 55 (DMO) of IC802 when the CD TEST MODE "STEP 4" or "STEP 5"? Yes test mode "step 4" No Check the periphery pins 28~32 of IC802. If OK. IC802 failure. test mode "step 5" DMO Normal. • No sound. Check the soldering and parts of IC14V. Is the wave output at pins 45~48 on IC14V? No Yes Check the soldering and parts of IC11V. Is the wave output at pins 1 and 7 on IC11V? Yes No Is the wave output at pins 14 and 17 on IC401? Yes Check the connection between IC11V and IC401. No Check areas between pins 5 and 26 on IC401 and IC601. – 46 – XL-3000V • Track search failure Does the sled motor run in FF/REW state when the SERVO TEST MODE "STEP1" is set? No Check as stated in item "SLED MOTOR OPERATION FAILURE". Yes Is the following wave output to the pin 49 (TRO) of IC802 during track search in normal playback? No IC802 failure. Yes TRO Is the following wave output to the pins 12 (TEO) of IC801 during track search in normal playback? No Yes TEO TEI Check the PWB pattern between pin 49 (TRO) of IC802 and pin 19 of IC804. Check the PWB pattern between pins 17 and 18 of IC804 and Optical pickup. If OK. Optical pickup failure. TEZI Is the above wave output to the pins 46 (TEI) and 47 (TEZI) of IC802 during track search in normal playback? No Check the PWB pattern between pin 12 (TEO) of IC801 and pins 46 and 47 of IC802. If OK. IC801 failure. No Check the PWB pattern between pin 17 (RFO) and 18 (RFIS), 19 (RFRP) of IC801 and pins 41 and 42 of IC802. If OK. IC801 failure. Yes Is the following wave output to the pin 41 (RFZI) and 42 (RFRP) of IC802 during track search in normal playback? Yes RFRP RFZI Normal. • Sled motor operation failure. Is following sled feed signal output the pin 53 (FMO) of IC802 when FF /REW key is pressed after the CD TEST MODE "STEP 1" is set? FF REW Yes C802 is faulty. No FMO Is following sled feed signal output the pins 3 and 4 of IC804 when FF /REW key is pressed after the CD TEST MODE "STEP 1" is set? FF Yes No Check the PWB pattern between pin 53 of IC802 and pins 3 and 4 of IC804. REW SL ± Is sled feed signal output the pins 1 and 2 of IC804? No Check the peripheral parts of IC804. If OK, IC804 is faulty. Yes Is sled feed voltage applied between both terminals of sled motor? Yes No Check the CNW803/CNS803. Check the CD mechanism (periphery of sled motor). If the sled motor does not run when DC2.0V is applied to both terminals of sled motor, the sled motor is faulty. • Sled servo failure. Is following sled signal output the pin 53 (FMO) of IC802 during playback? IC802 is faulty. No Yes FMO Normal. – 47 – XL-3000V FUNCTION TABLE OF IC IC401 VHiLC75342M-1: Function/Volume Equalizer (LC75342M) Pin No. Port Name Function 1 DI Serial data and clock input pin for control. 2 CE Chip enable pin. Data written into an internal latch in a timing of [H] -> [L]. Each analog switch is activated. Data transfer enabled at [H] level. 3 VSS Ground pin. 4 TEST Electronic volume control pin. To be set to the VSS potential. 5 LOUT Volume + equalizer output pin. 6 LBASS2 Bass-band filter comprising capacitor and resistor connection pin. 7 LBASS1 Bass-band filter comprising capacitor and resistor connection pin. 8 LTRE Capacitor connection pin comprising treble band filter. 9 LIN Volume + equalizer input pin. 10 LSEL0 Input selector output pin. 11 L4 Input signal pin. 12* L3 Input signal pin. 13 L2 Input signal pin. 14 L1 Input signal pin. 15* NC No CONNECT pin. To be open or connected to VSS. 16* NC No CONNECT pin. To be open or connected to VSS. 17 R1 Input signal pin. 18 R2 Input signal pin. 19* R3 Input signal pin. 20 R4 Input signal pin. 21 RSEL0 Input selector output pin. 22 RIN Volume + equalizer input pin. 23 RTRE Capacitor connection pin comprising treble band filter. 24 RBASS1 Bass-band filter comprising capacitor and resistor connection pin. 25 RBASS2 Bass-band filter comprising capacitor and resistor connection pin. 26 ROUT Volume + equalizer output pin. 27* NC No CONNECT pin. To be open or connected to VSS. 28 Vref 0.5 x VDD voltage generation block for analog ground. Capacitor of several 10µF to be connected between Vref and AWSS (VSS) as a counter measure against power ripple. 29 VDD Supply pin. 30 CL Serial data and clock input pin for control. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 48 – XL-3000V IC401 VHiLC75342M-1: Function/Volume Equalizer (LC75342M) TEST VSS CE 4 3 2 DI CL VDD Vref NC 1 30 29 27 28 LOUT 5 CONTROL CIRCUIT LBASS1 7 LTRE 8 RVref 25 RBASS2 24 RBASS1 CONTROL CIRCUIT LBASS2 6 LOGIC CIRCUIT CCB INTERFACE LVref 26 ROUT 23 RTRE 22 RIN LIN 9 21 RSEL0 LSEL0 10 11 12 13 14 15 16 17 18 19 20 L4 L3 L2 L1 NC NC R1 R2 R3 R4 Figure 49 BLOCK DIAGRAM OF IC – 49 – XL-3000V IC701 RH-iX0038SJZZ: System Microcomputer/FL driver (IX0038SJ) (1/2) Pin No. Terminal Name Input/Output 1-4 COM3-COM0 5-7 VLC3-VLC1 8 VDD Output — Input Function LCD common output terminal. LCD power supply terminal. Microcomputer power supply +5V. 9 OSC2 Output Oscillator ground terminal for main clock. f=8MHz 10 OSC1 Input Oscillator ground terminal for main clock. f=8MHz 11 VSS 12 XI Input Oscillator ground terminal for sub clock. f=32.768kHz 13 XO Output Oscillator ground terminal for sub clock. f=32.768kHz 14 MMOD 15 VREF- 16 KEY0 AN0/PA0 Input CD lid status detection input. 17 KEY1 AN0/PA1 Input Operation button input, Max-8 buttons. 18 KEY2 AN0/PA2 Input Operation button input, Max-8 buttons. 19 KEY3 AN0/PA3 Input MODEL/TUNER destination input. 20 KEY4 AN0/PA4 Input Current detection of CD lid control motor. Used to decide the CD lid drive error to control it. 21 KEY5 AN0/PA5 Input Fan motor auto adjustment mode selection input. 22* KEY6 AN0/PA6 Input — Input — Microcomputer power supply GND. Memory mode selection terminal. Power supply GND for AD converter. 23* KEY7 AN7/PA7 Input Tuner signal meter (S meter) voltage input terminal. 24 VREF+ Input Power supply for A/D converter +5V. 25 TXD SBO0/P00 Output 26 RXD SBI0/P01 Input 27 SBT0/P02 Output Synchronous clock output with TUNER PLL IC. 28 SBO1/P03 Output VIDEO CD DECORDER DATA output. 29 SBI1/P04 Output VIDEO CD DECORDER DATA input. 30 SBT1/P05 Output VIDEO CD DECORDER CLOCK signal. 31 DK/BZER P06 Output VIDEO CD DECORDER BUSY signal. 32 RST/P27 Input Data output terminal to TUNER PLL IC. Data input from TUNER PLL IC. Reset signal input. 33* RMOUT P10 Input CLOCK/TIMER/SLEEP button input. 34 P11 Input Tape run/END detection input. 35 TM2IO P12 Output 36* TM3IO P13 Output 37 TM4IO P14 Input Power (POWER) button input detection. 38 IRQ0 P20 Input Switches to the HALT mode when changing to . "L" at power failure detection input. 39 SENS IRQ1/P21 Input Remote control signal input. 40 IRQ2 P22 Input VIDEO CD DECORDER STROBE signal. 41* IRQ3 P23 Input 42* IRQ4 P24 Input 43 P30 Output SURROUND control output. 44 P31 Output POWER IC STAND-BY terminal CONTROL. 45 P32 Output Power mute output. "H" = MUTE ON "L" = MUTE OFF 46 LED0 WE/P50 Output CD servo power supply circuit control output. "H" = CD power ON "L" = CD power OFF 47 LED1 RE/P51 Output Main TRANS RELAY CONTROL. "H" = ON "L" = OFF 48* LED2 CS/P52 Input Data input from RDS IC. 49 LDE3/S51 A16/P53 Input Radio stereo broadcast reception detection input. "L" = During stereo broadcast reception 50 LED4/S50 A17/P54 Input 51 SEG49 P60/A0 Output CD LID output signal. Recording bias oscillation frequency selection control output. Broadcast reception status detection input. "L" = During broadcasting signal reception LCD backlight control signal output. "H" = Backlight ON, "L" = Backlight OFF 52 SEG48 P61/A1 Output Amp. signal detection. 53 SEG47 P62/A2 Output LED illumination control. "H" = ON "L" = OFF In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 50 – XL-3000V IC701 RH-iX0038SJZZ: System Microcomputer/FL driver (IX0038SJ) (2/2) Pin No. Terminal Name Input/Output Function 54 SEG46 P63/A3 Output LED dimmer signal. 55 SEG45 P64/A4 Output Fan control signal. 56 SEG44 P65/A5 Output Electric CD lid OPEN. 57 SEG43 P66/A6 Output Electric CD lid CLOSE. 58* SEG42 P67/A7 Input 59* SEG41 P70/A8 Output 60 SEG40 P71/A9 Output 61*-64* SEG39 P72/A10- Input/Output SEG36 P75/A13 65* SEG35 P76/A14 Output Data synchronous clock output. 66* SEG34 P77/A15 Output Chip enable terminal. "L" = BUS terminal active 67 SEG33 P87/D7 Output LCD segment output. 68 SEG32 P86/D6 Output LCD segment output. 69-74 SEG31 P85/D5SEG26 P80/D0 Output LCD segment output. 75-100 SEG25-SEG0 Output LCD segment output. ON/OFF output terminal of CD servo control IC. "H" = Servo ON "L" = Servo stand-by Data input/output terminal control. 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 S S S S S S S S S S S S S S S S S S S S S S S S S SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 IC701 RH-iX0038SJZZ: System Microcomputer/FL driver (IX0038SJ) I O I I I I I I I I I O 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 O I 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 I O O O O O I I I O O I I I I I I O O O O O O O I O O O O DO CL VD_DO VD_DI ACK BUSY RESET NC CE CLID_OUT NC POWER SYS_STOP REMOCON STB NC NC SURR P-STB P-MUTE CD+B P-CONT NC STEREO SD COM3 COM2 COM1 COM0 VLC3 VLC2 VLC1 VDD OSC2 OSC1 VSS XI XO MMOD VREF– CLID_SW KEY1 KEY2 MODEL CLID_PRO MOT_DEC NC NC VREF+ DI Figure 51 BLOCK DIAGRAM OF IC – 51 – S S S S S S S S S O O I/O I/O I/O I/O O O I O O O O O SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 NC NC NC NC NC NC CD_STB CD_RES PU-IN CLID_DW CLID_UP FAN DIMMER LIGHT AMP_DEC O B-LIGHT XL-3000V IC801 VHiTA2109F/-1:Servo Pre Amp. (TA2109F) Pin No. Function Input/Output Terminal Name 1 VCC — 2 FNI Input Main beam amp input terminal 3 FPI Input Main beam amp input terminal 4 TPI Input Sub-beam amp input terminal 5 TNI Input Sub-beam amp input terminal 6 MDI Input Monitor photodiode amp input terminal 7 LDO Output 8 SEL Input Laser diode control signal input and APC circuit ON/OFF signal input terminal 9 TEB Input Tracking error balance adjustment signal input terminal To be controlled by 3-value PWM signal. (PWM carrier = 88.2 kHz) 10 2VRO 11 TEN Input 12 TEO Output 13 SBAD Output Sub-beam addition signal output terminal 14 FEO Output Focus error signal generation amp output terminal 15 FEN Input 16 VRO Output Standard voltage (VR) output terminal. When Vcc = 5V, VR = 2.1V. 17 RFRP Output Track count signal generation amp output terminal 18 RFIS 19 RFGO Output 20 RFGC Input RF amplitude adjustment control signal input terminal The amplitude of RF signal can be controlled by using the 3-value PWM signal (PWM carrier = 88.2 kHz) which is output from the RFGC terminal of TC9432F. 21 AGCI Input RF signal amplitude adjustment amp input terminal 22 RFO Output 23 GND — 24 RFN Input Output Input Power voltage terminal Laser diode amp output terminal Standard voltage (2VR) output terminal. When Vcc = 5V, 2VR = 4.2V. Tracking error signal generation amp reversed phase input terminal Tracking error signal generation amp output terminal Focus error signal generation amp reversed phase input terminal RFRP detection circuit input terminal RF signal output terminal RF signal generation amp output terminal GND terminal RF reversed phase input terminal IC801 VHiTA2109F/-1:Servo Pre Amp. (TA2109F) 15kΩ 15kΩ SBAD 13 7.67kΩ 12 TEO 30kΩ 20µA 50kΩ 10pF 20pF 10kΩ 10kΩ 36pF 21kΩ 29kΩ 24kΩ 24kΩ 11 TEN 7.96kΩ 10 2VRO 10kΩ VRO 16 21kΩ RFRP 17 20kΩ 50µA 47kΩ SW1 12kΩ LDC 1kΩ SW2 65µA SW3 PEAK BOTTOM RFGO 19 8 SEL 1.74kΩ 20kΩ 20kΩ 9 TEB 3 STATE DET. 21kΩ 12kΩ RFIS 18 SEL 10kΩ FEO 14 FEN 15 30kΩ 10kΩ 7 LDO 680kΩ 180kΩ 13kΩ 20pF RFGC 20 2.12kΩ 6 MDI I.I 5 TNI I.I 4 TPI 180kΩ 12kΩ AGCI 21 20pF 23.5kΩ re = 130Ω 20kΩ 180kΩ RFO 22 40pF 20kΩ 60kΩ 3 FPI 20kΩ 2 FNI 40pF 20kΩ 1 VCC 3.3kΩ 3.3kΩ RFN 24 1.53kΩ 180kΩ 60kΩ GND 23 Figure 52 BLOCK DIAGRAM OF IC – 52 – L HiZ H LDC SW1 SW2 ON OFF OFF ON OFF ON SW3 OFF ON ON XL-3000V IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (1/3) Pin No. Port Name Function Input/Output 1* TEST0 Input Test mode terminal. To be opened usually. 2* 3* /HSO /UHSO Output Output Playback speed mode flag output terminal. /UHSO /HSO Playback speed H H x1 speed playback H L x2 speed playback L H x4 speed playback L L — 4* EMPH Output Sub-code Q data emphasis flag output terminal. "H": Emphasis ON "L": Emphasis OFF The output polarity can be inverted by command. 5 LRCK Output Channel clock (44.1 kHz) output terminal. "L": L channel "H": R channel The output polarity can be inverted by command. 6 VSS — 7 BCK Output 8 AOUT Output Audio data output terminal. 9 DOUT Output Digital out output terminal. 10* MBOV Output Buffer memory over signal output terminal. "H": Over 11* IPF Output Correction flag output terminal. "H": When AOUT output is correction-disabled symbol in case of C2 correction output. 12* SBOK Output 13* CLCK Input/Output 14 VDD Input Digital + power terminal. 15 VSS — Digital ground terminal. 16* DATA Output Sub-code P-W data output terminal. 17* SFSY Output Playback system frame sync signal output terminal. 18* SBSY Output Sub-code block sync output terminal. "H": On S1 position when the sub-code sync is detected. 19* SPCK Output Processor status signal read clock (176.4 kHz) output terminal. 20* SPDA Output Processor status signal output terminal. 21* COFS Output Correction system frame clock (7.35 kHz) output terminal. 22* MONIT Output LSI internal signal monitor terminal. It is possible to monitor the DSP internal flag and PLL system clock with the microcomputer command. Terminal for serial output of text data according to command . 23 VDD Input Digital + power terminal. 24 TESIO0 Input Test input/output terminal. To be fixed to "L" usually. Terminal to input the text data read clock according to command. — Digital ground terminal. Bit clock (1.4122 MHz) output terminal. Sub-code Q data CRCC judgment result output terminal. "H": When judgment result is OK. Sub-code P-W data read clock output/input terminal. Selectable with command bit. 25 P2VREF 26* HSSW 27* ZDET Output 1-bit DAC zero detection flag output terminal. 28 PDO Output Terminal to output the phase difference between EFM signal and PLCK signal. 29* TMAXS Output TMAX detection result output terminal. To be selected with command bit TMPS. 30 TMAX Output TMAX detection result output terminal. To be selected with command bit TMPS. Output 2VREF terminal for PLL system. VREF voltage in case of x2 speed/x4 speed. TMAX detection result TMAX output Longer than specific period "P2VREF" Shorter than specific period "VSS" Within specific period "HIZ" 31 LPFN Input 32 LPFO Output 33 PVREF Input VREF terminal for PLL system. 34 VCOREF Input VCO center frequency standard level terminal. To be fixed to PVref usually. 35 VCOF 36 AVSS — 37 SLCO Output 38 RFI Output Input Low-pass filter amp inverted input terminal. Low-pass filter amp output terminal. VCO filter terminal. Analog system ground terminal. Data slice level generation DAC output terminal. RF signal input terminal. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 53 – XL-3000V IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (2/3) Pin No. Port Name Function Input/Output 39 AVDD Input Analog system power terminal. 40 RFCT Input RFRP signal center level input terminal. 41 RFZI Input RFRP zero cross input terminal. 42 RFIP Input RF ripple signal input terminal. 43 FEI Input Focus error signal input terminal. 44 SBAD Input Sub-beam addition signal input terminal. 45 TSIN Input Test input terminal. To be fixed to Vref usually. 46 TEI Input Tacking error input terminal. (Tracking servo ON: Taking-in). 47 TEZI Input Tracking error, zero cross input terminal. 48 FOO Output 49 TRO Output 50 VREF Input 51 RFGC Output RF amplitude adjustment control signal output terminal. 3-value PWM signal is output. (PWM carrier = 88.2 kHz) 52 TEBC Output Tracking balance control signal output terminal. 3-value PWM signal is output. (PWM carrier = 88.2 kHz) 53 FMO Output Feed equalizer output terminal. 3-value PWM signal is output. (PWM carrier = 88.2 kHz) 54* FVO Output Speed error signal or feed search EQ output terminal. 3-value PWM signal is output. (PWM carrier = 88.2 kHz) 55 DMO Output Disc equalizer output terminal. 3-value PWM signal is output. (PWM carrier = DSP system 88.2 kHz, sync with PXO) 56 2VREF 57 SEL Output APC circuit ON/OFF signal output terminal. When laser is ON and UHS = L, "Hi-Z". When UHS = H, "H" output is obtained. 58* FLGA Output Internal signal monitor external flag output terminal. TEZC, FOON, FOK and RFZC signals can be selected with command. 59* FLGB Output Internal signal monitor external flag output terminal. DFCT, FOON, FMON and RFZC signals can be selected with command. 60* FLGC Output Internal signal monitor external flag output terminal. TRON, TRSR, FOK, and SRCH signals can be selected with command. 61* FLGD Output Internal signal monitor external flag output terminal. TRON, DMON, HYS and SHC signals can be selected with command. 62 VDD Input Input Focus equalizer output terminal. Tracking equalizer output terminal. Analog standard power terminal. Analog standard power terminal (2xVREF) Digital + power terminal. 63 VSS — 64* 65* 66* 67* IO0 IO1 IO2 IO3 Input/Output 68* /DMOUT Input Terminal to set the mode to output 2-value PWM of feed equalizer from IO0,1 terminal and 2value PWM of disc equalizer from IO2,3 terminal. "L" active 69* /CKSE Input To be opened usually. 70* /DACT Input DAC test mode terminal. To be opened usually. 71 TESIN Input Test input terminal (externally provided VCO clock input terminal). To be fixed to "L" usually. 72 TESIO1 Input Test input/output terminal. To be fixed to "L" usually. 73 VSS — 74 PXI Input 75* PXO Output 76 VDD Input 77 XVSS — 78 XI Input 79 XO Output 80 XVDD Input System clock oscillation circuit + power terminal. 81 DVSR Input R channel D/A converting section power terminal. 82* RO Output Digital ground terminal. General-use I/O port. The input port and output port can be selected with command. In case of input port the terminal state (H/L) can be read with the read command. In case of output port the terminal state (H/L/HiZ) can be controlled with command. Digital ground terminal. DSP system clock oscillation circuit input terminal. To be fixed to "L" usually. DSP system clock oscillation circuit output terminal. Digital + power terminal. System clock oscillation circuit ground terminal. System clock oscillation input terminal. System clock oscillation circuit output terminal. R channel data forward rotation output terminal. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 54 – XL-3000V IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (3/3) Function Input/Output Port Name Pin No. 83 DVDD Input D/A converting section power terminal. 84 DVR Input Reference voltage terminal. 85* LO 86 DVSL Input L channel D/A converting section power terminal. 87* TEST1 Input Test mode terminal. To be opened usually. 88* TEST2 Input Test mode terminal. To be opened usually. 89* TEST3 90-93 BUS0-BUS3 94 VDD Input Digital + power terminal. 95 VSS — Digital ground terminal. 96 BUCK Input Microcomputer interface clock input terminal. 97 /CCE Input Microcomputer interface chip enable signal input terminal. "L": BUS0 to 3 is active. 98* TEST4 Input Test mode terminal. To be opened usually. Output L channel data forward rotation output terminal. Input Test mode terminal. To be opened usually. Input/Output Microcomputer interface data input/output terminal. 99* /TSMOD Input Local test mode selection terminal. 100 /RST Input Reset signal input terminal. "L": Reset. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. Figure 55 BLOCK DIAGRAM OF IC – 55 – XO 79 XVDD 80 99 100 98 97 /CCE 96 BUCK 95 VSS 94 VDD 93 BUS3 92 BUS2 91 BUS1 90 BUS0 89 TEST3 88 TEST2 87 TEST1 86 DVSL 85 LO 84 DVR 83 LPF XI 78 VDD 76 PXI 74 VSS 73 TESIN 71 TESIO1 72 /DACT 70 /CKSE 69 /DMOUT 68 IO3 67 IO2 66 IO1 65 IO0 64 VSS 63 VDD 62 FLGD 61 FLGC 60 FLGB 59 SEL 57 PWM XVSS 77 1Bit DAC PXO 75 D/A Microcomputer interface RAM ROM Address circuit TEST4 DVDD 82 Synchronizing signal guarantee EFM demodulation Correction circuit /RST RO 81 1 TEST0 2 /HSO 3 /UHSO 4 EMPH 5 LRCK 6 VSS 7 BCK 8 AOUT 9 DOUT 10 MBOV 11 IPF 12 SBOK 13 CLCK 14 VDD 15 VSS 16 DATA 17 SFSY 18 SBSY 19 SPCK 20 SPDA 21 COFS 22 MONIT 23 VDD 25 P2VREF 24 TESIO0 Digital equalizer adjustment circuit FLGA 58 VREF 16KRAM Servo control 2VREF 56 TRO Audio output circuit Clock generator FVO 54 FOO CLV servo A/D DMO 55 TEZI Data slicer FMO 53 TEI Digital out VCO TEBC 52 TSIN Sub-code demodulation circuit Status RFGC 51 SBAD 26 HSSW 27 ZDET 28 PDO PLL TMAX 31 32 34 35 36 37 38 41 FEI 49 RFRP 50 RFZI 42 RFCT 43 AVDD 44 RFI 45 SLCO 46 AVSS 47 VCOF 48 VCOREF 39 PVREF 40 LPFO 33 LPFN 29 TMAXS 30 TMAX IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) DVSR /TSMOD XL-3000V IC804 VHiMM1469XH-1: Focus/Tracking/Spin/Sled Driver (MM1469XH) Pin No. Port Name Function 1 CH1-OUT-A Driver CH1 negative output 2 CH1-OUT-B Driver CH1 positive output 3 CH1-IN-A Driver CH1 input 4 CH1-IN-B Driver CH1 input, gain adjustment pin 5 Tr-B Connect to external transistor base 6 VREG-OUT Constant voltage output, connects to external transistor collector 7 MUTE Driver mute control input 8 GND GND 9 CH2-IN-B Driver CH2 input, gain adjustment pin 10 CH2-IN-A Driver CH2 input 11 CH2-OUT-B Driver CH2 positive output 12 CH2-OUT-A Driver CH2 negative output 13 Substrate GND Substrate GND 14* OP-OUT Operational amplifier output 15* OP-IN(–) Operational amplifier input, negative 16* OP-IN(+) Operational amplifier input, positive 17 CH3-OUT-A Driver CH3 negative output 18 CH3-OUT-B Driver CH3 positive output 19 CH3-IN-A Driver CH3 input 20* CH3-IN-B Driver CH3 input, gain adjustment pin 21 Vcc Vcc 22 Vcc Vcc 23 BIAS-IN Bias amplifier input 24 CH4-IN-B Driver CH4 input, gain adjustment pin 25 CH4-IN-A Driver CH4 input 26 CH4-OUT-B Driver CH4 positive output 27 CH4-OUT-A Driver CH4 negative output 28 Substrate GND Substrate GND In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. GND (lowest potential) is connected to the frame of pin center. CH3-IN-A 19 10kΩ 18 17 D.BUF D.BUF 14 Level shift DRIVER MUTE 50kΩ 10kΩ 10kΩ VREG-OUT MUTE 10 CH2-OUT-A Tr-B 9 Figure 56 BLOCK DIAGRAM OF IC – 56 – D.BUF D.BUF 11 12 8 CH2-OUT-B 7 CH2-IN-A 6 CH2-IN-B 5 GND 4 CH1-IN-B CH1-IN-A 13 50kΩ 10kΩ Level shift CH1-OUT-B 15 10kΩ VCC 10kΩ CH1-OUT-A 16 Level shift T.S.D D.BUF D.BUF 1 2 3 OP-IN(–) CH3-IN-B 20 OP-OUT Vcc 21 VCC OP-IN(+) Vcc 22 SUBGND BIAS-IN 23 CH3-OUT-A CH4-IN-B 24 CH3-OUT-B CH4-IN-A CH4-OUT-B 26 25 27 D.BUF D.BUF Level shift 28 CH4-OUT-A SUBGND T.S.D : Thermal Shut Down D.BUF : Driver Buffer XL-3000V IC14V VHiES3883F/-1: Video CD Encoder (ES3883F) (1/2) Pin No. 1 Terminal Name VSS Function Input/Output Input — Ground. 2*-4* NC 5 VCC Input Voltage supply, 5V. 6 DSC_CLK Input Clock for programming to access internal registers. 7 AUX0 Input/Output 8 DSC_D0 Input/Output Data for programming to access internal registers. 9 AUX1 Input/Output Servo Reverse Control pin. 10 DSC_STB 11 AUX2 12* DCLK/EXT_CLK 13 RESET_B 14 AUX07 Input/Output 15* MUTE Output Input Input/Output Output No connect. Do not connect to these pins. Servo Forward Control pin. Strobe for programming to access internal registers. Servo LDON or Control pin. Dual-purpose pin. DCLK is the MPEG decoder clock. Input EXT_CLK is the extemal clock. EXT_CLK is an input during bypass PLL mode. Input Video reset (active low). Servo BRKM/Sense or Control pin/VFD_DI. Audio mute. 16 VCC Input Voltage supply, 5V. 17 MCLK Input Audio master clock. 18 AUX8 Input/Output 19 TWS/SPLL_OUT Input Output Servo Mute/Open or Control pin/VFD_CLK. Dual-purpose pin. TWS is the transmit audio frame sync. SPLL_OUT is the select PLL output. 20* AUX09 Input/Output Servo SQS0 or Control pin. 21 22 TSD Input Transmit audio data input. TBCK Input 23 RWS/SEL_PLL1 Output 23 RWS/SEL_PLL1 Input 24 RSTOUT_B 25, 26 VSS 27* NC (SQCK) — No connect. Do not connect to these pins. 28* NC (SQSO) — No connect. Do not connect to these pins. 29*, 30* NC — No connect. Do not connect to these pins. 31 VSS Input Ground. 32 VCC Input Voltage supply, 5V. 33 RSD/SEL_PLL0 Output 33 RSD/SEL_PLL0 Input 34 AUX10 Input/Output Servo SQCK or Control pin. 35 AUX11 Input/Output 3880 IRQ or Interrupt Output or Control pin. 36* AUX12 Input/Output CD C2PO or Interrupt or Control pins. 37 RBCK/SER_IN Output Input Output Input Transmit audio bit clock. Dual-purpose pin. RWS is the receive audio frame sync. Pins SEL_PLL [1:0] select the PLL clock frequency for DCLK output. SEL_PLL1 SEL_PLL0 DCLK 0 0 Bypass PLL (Input Mode) 0 1 27MHz (Output Mode) 1 0 32.4MHz (Output Mode) 1 1 40.5MHz (Output Mode) Reset output (active low). Ground. Dual-purpose pin. RSD is the receive audio data input. SEL_PLL0 along with SEL_PLL1 select the PLL clock frequency for the DCLK output. See the table for pin number 23. Dual purpose pin. RBCK is the receive audio bit clock. SER_IN is serial input DSC mode. 0 = Parallel DSC mode. 1 = Serial DSC mode. 38 AUX13 Input/Output Serial Interrupt/CD-Mute or Control pin. 39 AUX14 Input/Output Servo SCOR(S0S1) or Interrupt Input or Control pin. 40 AUX15 Input/Output Interrupt Input or Control pin. 41 VSSA Input Audio Analog ground. 42 VCM Input ADC Common Mode Reference (CMR) buffer output. CMR is approximately 2.25V. Bypass to analog ground with 47 µF electrolytic in parallel with 0.1 µF. 43 VREFP Input DAC and ADC maximum reference. Bypass to VCMR with 10 µF in parallel with 0.1 µF. 44 VCCAA Input Analog VCC, 5V. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 57 – XL-3000V IC14V VHiES3883F/-1: Video CD Encoder (ES3883F) (2/2) Pin No. Terminal Name Input/Output Function 45 AOR + Output Right channel output. 46 AOR - Output Right channel output. 47 AOL - Output Left channel output. 48 AOL + Output Left channel output. 49* MIC1 Input Microphone input 1. 50* MIC2 Input Microphone input 2. 51 VSSAA Input Audio Analog ground. 52 VREF Input Internal resistor divider generates Common Mode Reference (CMR) voltage. Bypass to analog ground with 0.1 µF. 53 VREFM Input DAC and ADC minimum reference. Bypass to VCMR with 10 µF in parallel with 0.1 µF. 54 RSET Input Full scale DAC current adjustment. 55 COMP Input Compensation pin. 56, 57 VSSAV Input Video Analog ground. 58* CDAC Output 59, 60 VCCAV Input 61* YDAC Output 62, 63 VSSAV Input 64 VDAC Output 65 ACAP Input 66 VCC Input 67* AUX6 Input/Output Modulated chrominance output. Video VCC, 5V. Y luminance data bus for screen video port. Video Analog ground. Composite video output. Audio CAP. Voltage supply, 5V. Servo XLAT or Control pin/VFD_DO. 68* AUX5 Input/Output Servo Data or Control pin. 69 AUX4 Input/Output Servo CCW/Close or Control pin. 70 AUX3 Input/Output Servo CW/Limit or Control pin. 71 XOUT Output 72 VSS Input Ground. 73 VCC Input Voltage supply, 5V. 74 XIN Input 27 MHz crystal input. 75 VSS Input Ground. 76* NC — 77 VSS Input 78 VCC Input 79 PCLK Input/Output 13.5 MHz pixel clock. 80 2XPCLK Input/Output 27 MHz (2 times pixel clock). 81 DSC_D7 Input/Output Data for programming to access internal registers. 82 HSYN_B Output 83 DSC_D6 Input/Output 84 VSYN_B Output 85 DSC_D5 Input/Output Crystal output. No connect. Do not connect to these pins. Ground. Voltage supply, 5V. Horizontal sync (active low). Data for programming to access internal registers. Vertical sync (active low). Data for programming to access internal registers. 86-89 YUV7-YUV4 Input YUV data bus for screen video port. 90 VCC Input Voltage supply. 5V. 91 VSS Input Ground. 92 YUV3 Input YUV data bus for screen video port. 93 DSC_D4 94 YUV2 95 DSC_D3 96 YUV1 97 DSC_D2 98 YUV0 99 DSC_D1 100 VSS Input/Output Input Input/Output Input Input/Output Input Input/Output Input Data for programming to access internal registers. YUV data bus for screen video port. Data for programming to access internal registers. YUV data bus for screen video port. Data for programming to access internal registers. YUV data bus for screen video port. Data for programming to access internal registers. Ground. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 58 – XL-3000V NC NC 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 NC NC NC NC NC IC14V ES3883F NC 50 MIC2 NC 49 MIC1 48 AOL + 47 AOL 46 AOR 45 AOR + 44 VCCAA 43 VREFP 42 VCM 41 VSSAA 40 AUX15/IR 39 AUX14/SOS1 NC 38 AUX13/SP 37 RBCK/SER_IN NC 36 AUX12/C2PO 35 AUX11/RQ 34 AUX10/SQCK 33 RSD/SEL_PLL0 32 VCC 31 VSS VSS NC NC NC VCC DSC_CLK AUX0 DSC_D0 AUX1 DSC_STB AUX2 DCLK/EXT_CLK RSTET_B AUX7/VFD_DI MUTE VCC MCLK AUX8/VFD_CLK TWS/SPLL_OUT AUX9/SQSO TSD TBCK RWS/SEL_PLL1 RSTOUT_B VSS VSS SQCK SQSO NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 DSC_D7 HSYN_B DSC_D6 VSYN_B DSC_D5 YUV7 YUV6 YUV5 YUV4 VCC VSS YUV3 DSC_D4 YUV2 DSC_D3 YUV1 DSC_D2 YUV0 DSC_D1 VSS NC NC 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 2XPCLK PCLK VCC VSS NC VSS XIN VCC VSS XOUT AUX3 AUX4 AUX5 AUX6/VFD_DO VCC ACAP VDAC VSSAV VSSAV YDAC VCCAV VCCAV CDAC VSSAV VSSAV COMP RSET VREFM VREF VSSAA ICV14 VHiES3883F/-1 :Video CD Encoder (ES3883F) Figure 59-1 BLOCK DIAGRAM OF IC IC16V RH-iX0025SJZZ: D-RAM 256Kx16 (IX0025SJ) Pin No. Port Name Function Vcc 1 40 Vcc DQ1 2 39 DQ16 DQ2 3 38 DQ15 Data input/data output DQ3 4 37 DQ14 11*,12* NC Not used DQ4 5 36 DQ13 13 WE Write enable Vcc 6 35 Vss 14 RAS Low address strobe DQ5 7 34 DQ12 15* NC Not used DQ6 8 33 DQ11 16-19 A0-A3 Address input 20 VCC Power (5V) DQ7 9 32 DQ10 1 VCC Power (5V) 2-5 DQ1-DQ4 Data input/data output 6 VCC Power (5V) 7-10 21 DQ5-DQ8 VSS DQ8 10 Ground 31 DQ9 22-26 A4-A8 Address input NC 11 30 NC 27 OE Output enable NC 12 29 LCAS 28 UCAS Upper column address strobe WE 13 28 UCAS 29 LCAS Lower column address strobe 30* NC Not used RAS 14 27 OE NC 15 26 A8 31-34 DQ9-DQ12 Data input/data output 35 VSS Ground A0 16 25 A7 36-39 DQ13-DQ16 Data input/data output A1 17 24 A6 40 VSS Ground A2 18 23 A5 A3 19 22 A4 Vcc 20 21 Vss In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. Figure 59-2 BLOCK DIAGRAM OF IC – 59 – XL-3000V IC15V VHiES3880F/-1: Video CD Decoder (ES3880F) Pin No. Terminal Name Input/Output Function 1 VDD Input 2 RAS# Output DRAM row address strobe (active low). 3 DWE# Output DRAM write enable (active low). 4-12 DA0-DA8 13-28 DBUS0-DBUS15 29 RESET# Input Ayatem reset (active low). 30 VSS Input Ground. 31 VDD Input Voltage supply for 3.3V. 32-39 YUV0-YUV7 40 VSYNC Input/Output Vertival sync for screen video interface, programmable for rising or falling edge. 41 HSYNC Input/Output Horizontal sync for screen video interface, programmable for rising or falling edge. 42* CPUCLK Input 43 PCLK2X Input/Output Pixel clock; two times the actual pixel clock for screen video interface. 44 PCLK Input/Output Pixel clock qualifier in for screen video interface. Input/Output Auxiliary control pins (AUX0 and AUX1 are open collectors). 45,46*-49 AUX0-AUX4 Output Input/Output Output Voltage supply for 3.3V. DRAM multiplaxed row and column address bus. DRAM data bus. Y is luminance, UV are chrominance data bus for screen video interface. YUV0-YUV7 for 8-bit YUV mode. RISC and system clock input. CPUCLK is used only if SEL_PLL0, SEL_PLL1=00. 50 VSS Input 51 VDD Input Ground. 52-54 AUX5-AUX7 Input/Output Auxiliary control pins. 55-62 LD0-LD7 Input/Output RISC interface data bus. 63* LWR# Output RISC interface write enable (active low). 64 LOE# Output RISC interface output enable (active low). 65 LCS3# Output RISC interface chip enable (active low). 66,67* LCS1#, LCS0# Output RISC interface chip enable (active low). 68-79 LA0-LA11 Output RISC interface address bus. Voltage supply for 3.3V. 80 VSS Input Ground. 81 VCC Input Digital supply voltage for 5V. 82-87 LA12-LA17 Output RISC interface address bus. 88 ACLK 89 AOUT/SEL_PLL0 Input/Output Output Input 90 ATCLK 91 ATFS/SEL_PLL1 Input/Output Output Input Output Master clock for external audio DAC (8.192 MHz, 11.2896 MHz, 12.288 MHz, 16.9344 MHz and 18.432 MHz). Dual-purpose pin. AOUT is the audio interface serial data output. Pins SEL_PLL0, SEL_PLL1 select phase-lock loop (PLL) clock frequency CPUCLK for the Visba: 00 = bypass PLL. 01 = 54 MHz PLL. 10 = 67.5 MHz PLL. 11 = 81 MHz PLL. Audio transmit bit clock. Dual-purpose pin. ATFS is the audio interface transmit frame sync. Pins SEL_PLL0, SEL_PLL1 select phase-lock loop (PLL) clock frequency CPUCLK for the Viaba. See the SEL_PLL0 pin above for the settings. 92 DA9/DOE# 93 AIN Input Audio interface serial data input. 94 ARCLK Input Audio receive bit clock. 95 ARFS Input Audio interface receive frame sync. 96 TDMCLK Input TDM interface serial clock. 97 TDMDR Input TDM interface serial data receive. 98 TDMFS Input 99 CAS# 100 VSS Output Input Dual purpose pin: DRAM output enable (active low)/DRAM multiplexed row column address bus. TDM interface frame sync. DRAM column address strobe bank 0 (active low). Ground. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 60 – XL-3000V VSS LA11 LA10 LA9 LA8 LA7 LA6 LA5 LA4 LA3 LA2 LA1 LA0 LCS0# LCS1# LCS3# LOE# LWR# LD7 LD6 LD5 LD4 LD3 LD2 LD1 LD0 AUX7 AUX6 AUX5 VDD IC15V VHiES3880F/-1: Video CD Decoder (ES3880F) NC NC 80 79 78 77 76 75 74 73 72 71 70 69 68 67 6665 64 63 62 61 60 59 58 57 56 55 54 53 52 51 81 50 82 49 83 48 84 47 85 NC 46 86 45 87 44 88 43 89 NC 42 90 41 91 40 92 39 93 38 94 37 95 36 96 35 97 34 98 33 99 32 100 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1516 17 18 19 20 21 22 23 24 25 26 27 28 29 30 ES3880F VDD RAS# DWE# DA0 DA1 DA2 DA3 DA4 DA5 DA6 DA7 DA8 DBUS0 DBUS1 DBUS2 DBUS3 DBUS4 DBUS5 DBUS6 DBUS7 DBUS8 DBUS9 DBUS10 DBUS11 DBUS12 DBUS13 DBUS14 DBUS15 RESET# VSS VCC LA12 LA13 LA14 LA15 LA16 LA17 ACLK AOUT/SEL_PLL0 ATCLK ATFS/SEL_PLL1 DA9/DOE# AIN ARCLK ARFS TDMCLK TDMDR TDMFS CAS# VSS Figure 61 BLOCK DIAGRAM OF IC – 61 – VSS AUX4 AUX3 AUX2 AUX1 AUX0 PCLK PCLK2X CPUCLK HSYNC VSYNC YUV7 YUV6 YUV5 YUV4 YUV3 YUV2 YUV1 YUV0 VDD XL-3000V LCD701: RV-LX0012SJZZ LCD Display z1 z4 z2 r z3 q 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 PinNo com1 1 com1 2 com2 com3 PinNo com1 com2 com3 com4 22 h5 j5 l5 k5 23 g5 n5 m5 d5 24 a5 p5 f5 e5 com4 25 RDS b6 c6 ST com4 com2 3 com3 4 5 z1 b1 c1 z2 26 h6 j6 l6 k6 6 h1 j1 l1 k1 27 g6 n6 m6 d6 7 g1 n1 m1 d1 28 a6 p6 f6 e6 8 a1 p1 f1 e1 29 r b7 c7 q 9 REC b2 c2 z3 30 h7 j7 l7 k7 10 h2 j2 l2 k2 31 g7 n7 m7 d7 11 g2 n2 m2 d2 32 a7 p7 f7 e7 12 a2 p2 f2 e2 33 TP b8 c8 13 SLEEP b3 c3 MHz 34 h8 j8 l8 k8 14 h3 j3 l3 k3 35 g8 n8 m8 d8 15 g3 n3 m3 d3 36 a8 p8 f8 e8 16 a3 p3 f3 e3 37 EON PTY TI TA 17 RANDOM b4 c4 kHz 38 SRS(0) 18 h4 j4 l4 k4 39 com4 19 g4 n4 m4 d4 40 20 a4 p4 f4 e4 41 21 MEMORY b5 c5 z4 42 Figure 62 LCD SEGMENT – 62 – com3 com2 com1 XL-3000V PARTS GUIDE VIDEO CD COMPACT AUDIO SYSTEM MODEL XL-3000V XL-3000V Video CD Compact Audio System consisting of XL3000V (main unit) and CP-XL3000U (speaker system). “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION For U.S.A. only Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP MARK: SPARE PARTS-DELIVERY SECTION Explanation of capacitors/resistors parts codes Capacitors Resistors VCC ....................... Ceramic type VCK ........................ Ceramic type VCT ........................ Semiconductor type VC • • MF ............... Cylindrical type (without lead wire) VC • • MN ............... Cylindrical type (without lead wire) VC • • TV ................ Square type (without lead wire) VC • • TQ ............... Square type (without lead wire) VC • • CY ............... Square type (without lead wire) VC • • CZ ............... Square type (without lead wire) VC • • • • • • • • • J .. The 13th character represents capacity difference. ("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%, "C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.) VRD ....................... Carbon-film type VRS ........................ Carbon-film type VRN ....................... Metal-film type VR • • MF ............... Cylindrical type (without lead wire) VR • • MN ............... Cylindrical type (without lead wire) VR • • TV ................ Square type (without lead wire) VR • • TQ ............... Square type (without lead wire) VR • • CY ............... Square type (without lead wire) VR • • CZ ............... Square type (without lead wire) VR • • • • • • • • • J .. The 13th character represents error. ("J" ±5%, "F" ±1%, "D" ±0.5%.) If there are no indications for the electrolytic capacitors, error is ±20%. If there are no indications for other parts, the resistors are ±5% carbon-film type. NOTE: Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace parts with specified ones for maintaining the safety and performance of the set. XL-3000V NO. PRICE RANK PARTS CODE DESCRIPTION INTEGRATED CIRCUITS IC10V IC11V IC14V IC15V IC16V IC201 IC301 IC302 IC303 RH-IX0041SJZZ VHINJM4565M-1 VHIES3883F/-1 VHIES3880F/-1 RH-IX0025SJZZ VHIKIA4558P-1 VHITA7358AP-1 VHILC72131/-1 VHILA1832S/-1 J J J J J J J J J AC BA BB AW AC AG AP AN IC401 VHILC75342M-1 J AN IC601 IC681,682 IC701 VHISTK40202-1 VHIKIA7805API RH-IX0038SJZZ J J J AW AF IC801 IC802 IC804 VHITA2109F/-1 VHITC9462F/-1 VHIMM1469XH-1 J J J AL AZ AN IC805 VHITA7291S/-1 J AH ROM 256×16,IX0041SJ Buffer Amp.,NJM4565M Video CD Encoder,ES3883F Video CD Decoder,ES3880F D-RAM 256K×16,IX0025SJ Surround Control,KIA4558P FM Front End,TA7358AP PLL (Tuner),LC72131 FM IF Det./FM Mpx./AM IF, LA1832S Function/Volume Equalizer, LC75342M Power AMP.,STK40202 Voltage Regulator,KIA7805API System Microcomputer/FL Driver, IX0038SJ Servo Pre Amp.,TA2109F Servo/Signal Control,TC9462F Focus/Tracking/Spin/Sled Driver, MM1469XH CD Lid Motor Driver,TA7291S J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AC AB AC AC AC AB AC AC AC AC AB AB AC AF AC AF AC AC AF AB AB AC AB AC AB AC AB AC AB AB AB AC AC AD AC AB AB AC AB AC Silicon,NPN,2SD1858 R2 Silicon,NPN,2SC1740 SR Silicon,NPN,KTC3200 GR Silicon,PNP,KTA1268 GR Silicon,NPN,KTC3200 GR FET,2SK246 GR Digital,NPN,KRC107 M Silicon,NPN,2SC535 C Silicon,NPN,2SC535 C Digital,NPN,KRC104 M Silicon,PNP,KTA1266 GR Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3200 GR Silicon,NPN,2SD2012 Y Silicon,NPN,KTC3200 GR Silicon,NPN,2SD2012 Y Digital,PNP,KRA102 M Digital,NPN,KRC107 M Silicon,NPN,2SD2012 Y Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3199 GR Digital,NPN,KRC102 M Silicon,NPN,KTC3199 GR Digital,NPN,KRC102 M Silicon,PNP,KTA1266 GR Digital,NPN,KRC102 M Silicon,PNP,KTA1266 GR Digital,NPN,KRC102 M Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3199 GR Silicon,PNP,KTA1266 GR Silicon,NPN,2SC535 C Silicon,NPN,KTC3200 GR Silicon,PNP,2SB562 C Digital,NPN,KRC102 M Silicon,PNP,KTA1266 GR Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3200 GR Silicon,PNP,KTA1266 GR Digital,NPN,KRC102 M TRANSISTORS Q11V Q12V Q101 Q102 Q103,104 Q201 Q203 Q302 Q306 Q351 Q360 Q601,602 Q603 Q604,605 Q606 1 Q607 Q608 Q609 1 Q610 Q681 Q683 Q701 Q702,703 Q706 Q707,708 Q709 Q801 Q802 Q803 Q804 Q805 Q806 Q807 Q861 Q901 Q902 Q903 Q904 Q907 Q908 VS2SD1858R2-1 VS2SC1740SR-1 VSKTC3200GR-1 VSKTA1268GR-1 VSKTC3200GR-1 VS2SK246GR/-1 VSKRC107M//-1 VS2SC535-C/-1 VS2SC535-C/-1 VSKRC104M//-1 VSKTA1266GR-1 VSKTC3199GR-1 VSKTC3200GR-1 VS2SD2012Y/-1 VSKTC3200GR-1 VS2SD2012Y/-1 VSKRA102M//-1 VSKRC107M//-1 VS2SD2012Y/-1 VSKTC3199GR-1 VSKTC3199GR-1 VSKRC102M//-1 VSKTC3199GR-1 VSKRC102M//-1 VSKTA1266GR-1 VSKRC102M//-1 VSKTA1266GR-1 VSKRC102M//-1 VSKTC3199GR-1 VSKTC3199GR-1 VSKTA1266GR-1 VS2SC535-C/-1 VSKTC3200GR-1 VS2SB562-C/-1 VSKRC102M//-1 VSKTA1266GR-1 VSKTC3199GR-1 VSKTC3200GR-1 VSKTA1266GR-1 VSKRC102M//-1 DIODES D201 D301,302 D305,306 D308 D401~403 D411,412 D602~604 D605,606 1 D651~654 1 D657~660 D681~686 D688,689 D720~723 VHD1N4148//-1 VHD1N4148//-1 VHD1N4148//-1 VHD1N4148//-1 VHD1N4004//-1 VHD1N4148//-1 VHD1N4148//-1 VHD1N4004//-1 VHD1N5402M/-1 VHD1N4004//-1 VHD1N4004//-1 VHD1N4004//-1 VHD1N4148//-1 J J J J J J J J J J J J J AA AA AA AA AB AA AA AB AE AB AB AB AA Silicon,1N4148 Silicon,1N4148 Silicon,1N4148 Silicon,1N4148 Silicon,1N4004 Silicon,1N4148 Silicon,1N4148 Silicon,1N4004 Silicon,1N5402M Silicon,1N4004 Silicon,1N4004 Silicon,1N4004 Silicon,1N4148 NO. D801 D802~805 D901,902 ZD351 ZD601 ZD602 ZD683,684 ZD701 ZD901 ZD902 PRICE RANK PARTS CODE DESCRIPTION VHPDB5306X+-1 VHD1N4004//-1 VHD1N4004//-1 VHEDZ5R1BSB-1 VHEDZ130BSA-1 VHEMTZJ9R1C-1 VHEMTZJ160C-1 VHEDZ3R3BSB-1 VHEDZ240BSD-1 VHEDZ5R6BSB-1 J J J J J J J J J J AR AB AB AC AC AB AB AB AB AC LED,DB5306X Silicon,1N4004 Silicon,1N4004 Zener,5.1V,DZ5.1BSB Zener,13V,DZ13BSA Zener,9.1V,MTZJ9.1C Zener,16V,MTZJ16C Zener,3.3V,DZ3.3BSB Zener,24V,DZ24BSD Zener,5.6V,DZ5.6BSB RFILR0008AWZZ RFILF0004SJZZ RFILF0003AWZZ RFILA0003SJZZ J J J J AE AG AK AF Band Pass Filter FM RF,10.7 MHz FM IF AM IF RCILA0007SJZZ RCILI0005SJZZ RCILB0009SJZZ RCILI0004SJZZ RTRNP0068SJZZ RTRNP0061SJZZ J J J J J J AG AF AG AF AM Tracking FM IF AM Band Coverage AM IF Power Transformer (Main) AM Power Transformer (Sub) VP-XF100K0000 VP-XF3R3K0000 RCILR0003SJZZ RCILB0010SJZZ VP-DH101K0000 VP-DH102K0000 VP-DH2R2K0000 VP-DHR82K0000 RCILZ0024AWZZ VP-DH100K0000 VP-DH2R2K0000 VP-DH100K0000 VP-XHR82K0000 VP-DH100K0000 VP-DH100K0000 J J J J J J J J J J J J J J J AB AB AD AG AB AB AB AE AC AB AB AB AC AB AB J AB 10 kohm (B),Semi-VR [FM Mute Level] FILTERS BF301 CF302,303 CF351 CF352 TRANSFORMERS T302 T304 T306 T351 1 T651 1 T681 COILS L11V L103V,104V L302 L303 L351,352 L353 L401 L402 L601,602 L603 L702 L801 L802 L803 L806 10 µH,Choke 3.3 µH,Choke FM RF FM OSC. 100 µH,Choke 1 mH,Choke 2.2 µH,Peaking 0.82 µH,Choke 3 µH,Choke 10 µH,Choke 2.2 µH,Peaking 10 µH,Choke 0.82 µH 10 µH,Choke 10 µH,Choke VARIABLE RESISTOR VR351 RVR-M0999AFZZ VARIABLE CAPACITORS TC100V VD301 VD302,303 RTO-H1004SJZZ VHCSVC348S/-1 VHCKDV147C/-1 J J J AF Trimmer,10 pF AK Variable Capacitance,SVC348S AH Variable Capacitance,KDV147C J J J J J J AG AG AF AG AE AL Crystal,27 MHz VCO,456 kHz Crystal,4.5 MHz Ceramic,8 MHz Crystal,32.768 kHz Crystal,16.93 MHz J J J J J J J J J J J J J J J AB AC AB AD AD AB AA AA AD 10 µF,50V,Electrolytic 1000 µF,6.3V,Electrolytic 22 µF,25V,Electrolytic 10 µF,50V,Electrolytic 3 pF,50V 100 µF,10V,Electrolytic 0.0015 µF,50V 0.1 µF,25V 10 µF,50V,Electrolytic 1 µF,16V 100 µF,50V,Electrolytic 0.0015 µF,50V 0.1 µF,25V 3 pF,50V 100 µF,10V,Electrolytic VIBRATORS X1V X351 X352 X701 X702 X801 RCRSB0002SJZZ RCRM-0007SJZZ RCRSP0006SJZZ RCRM-0008SJZZ RCRSP0007SJZZ RCRSP0002SJZZ CAPACITORS C101,102 C101V C102V,103V C103 C104 C104V C105 C105V C106 C106V C107 C108 C108V C109 C109V –1– RC-GZA106AF1H RC-GZV108AF0J RC-GZA226AF1E RC-EZ0002SJZZ VCCSCY1HL3R0C RC-GZA107AF1A VCKYPA1HB152K VCKYCY1EF104Z RC-EZ0002SJZZ VCKYCY1CF105Z RC-EZ0003SJZZ VCKYPA1HB152K VCKYCY1EF104Z VCCSCY1HL3R0C RC-GZA107AF1A AD AA AA AD AB XL-3000V NO. PARTS CODE C110 C110V~112V C111,112 C113 C114 C115V C116 C116V,117V C118V C119V,120V C120 C121V C122V C124V C125,126 C125V C126V,127V C129V C130V C131V C135V,136V C137V~140V C141V~144V C147V,148V C149V,150V C158V C159V,160V C161V C162V C164V C165V C166V C167V,168V C169V C171V,172V C183V C184V C201,202 C203,204 C208 C209 C211,212 C213,214 C215 C216 C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 C316 C317 C318 C319 C329 C330 C331 C332 C334 C335 C337 C343 C349 C350,351 C352 C353,354 C355 C356 C357 C358 C360,361 C362 VCKYPA1HB102K VCKYCY1EF104Z RC-EZ0002SJZZ VCKYPA1HF223Z RC-EZ0003SJZZ RC-GZA226AF1E VCKYPA1HF223Z VCKYCY1EF104Z RC-GZA226AF1E VCKYCY1EF104Z RC-GZA227AF1C RC-GZA226AF1E VCKYCY1EF104Z VCKYCY1EF104Z RC-GZW228AF1V RC-GZA107AF1A VCKYCY1EF104Z VCCCCY1HH270J VCKYCY1EF104Z VCCCCY1HH102J VCKYCY1EF104Z RC-GZA106AF1E VCCCCY1HH330J RC-GZA107AF1A VCKYCY1EF104Z RC-GZA107AF1A VCKYCY1EF104Z RC-GZA107AF1A VCKYCY1EF104Z RC-GZA476AF1A VCKYCY1EF104Z RC-GZA226AF1E VCCCCY1HH220J VCKYCY1EF104Z RC-GZA106AF1E VCCCCY1HH220J VCKYCY1EF104Z VCKYCY1HB562K RC-GZA105AF1H RC-GZA107AF1C RC-GZA476AF1C VCKYCY1HB332K RC-GZA475AF1H RC-GZA105AF1H RC-EZD105AF1H VCKYPA1HF123Z VCKYCY1HB102K VCKYCY1HB102K VCKYCY1EF103Z VCKYCY1HB472K VCCUCY1HJ7R0D VCKYCY1HB472K VCKYCY1EF223Z VCKYCY1HB102K VCKYCY1EF223Z VCCCCY1HH100J VCCSCY1HL330J VCCUCY1HJ6R0D VCCCCY1HH220J VCKYCY1HB101K RC-GZA106AF1C VCKYCY1EF223Z VCCSCY1HL5R0C VCCCCY1HH180J VCKYCY1EF223Z VCCCPA1HH120J VCKYCY1EF473Z VCKYPA1HF223Z VCCUPA1HJ270J VCKYCY1HB561K VCKYPA1HF223Z VCCSCY1HL330J VCKYCY1HB102K VCKYCY1EF223Z RC-GZA106AF1C VCKYCY1EF223Z VCCSCY1HL220J VCKYCY1HB102K RC-GZA225AF1H RC-GZA105AF1H VCKYCY1EF223Z RC-GZA335AF1H PRICE RANK J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AD AB AD AB AB AA AB AA AB AB AA AA AF AB AA AA AA AA AA AA AA AB AA AB AA AB AA AB AA AB AA AA AA AA AA AA AB AB AB AA AB AB AB AD AA AA AA AA AB AA AB AA AB AA AD AB AA AB AB AB AD AA AB AA AB AB AA AA AB AD AA AB AB AB AD AA AB AB AB AB DESCRIPTION NO. 0.001 µF,50V 0.1 µF,25V 10 µF,50V,Electrolytic 0.022 µF,50V 100 µF,50V,Electrolytic 22 µF,25V,Electrolytic 0.022 µF,50V 0.1 µF,25V 22 µF,25V,Electrolytic 0.1 µF,25V 220 µF,16V,Electrolytic 22 µF,25V,Electrolytic 0.1 µF,25V 0.1 µF,25V 2200 µF,35V,Electrolytic 100 µF,10V,Electrolytic 0.1 µF,25V 27 pF (CH),50V 0.1 µF,25V 0.001 µF (CH),50V 0.1 µF,25V 10 µF,25V,Electrolytic 33 pF (CH),50V 100 µF,10V,Electrolytic 0.1 µF,25V 100 µF,10V,Electrolytic 0.1 µF,25V 100 µF,10V,Electrolytic 0.1 µF,25V 47 µF,10V,Electrolytic 0.1 µF,25V 22 µF,25V,Electrolytic 22 pF (CH),50V 0.1 µF,25V 10 µF,25V,Electrolytic 22 pF (CH),50V 0.1 µF,25V 0.0056 µF,50V 1 µF,50V,Electrolytic 100 µF,16V,Electrolytic 47 µF,16V,Electrolytic 0.0033 µF,50V 4.7 µF,50V,Electrolytic 1 µF,50V,Electrolytic 1 µF,50V,Electrolytic 0.012 µF,50V 0.001 µF,50V 0.001 µF,50V 0.01 µF,25V 0.0047 µF,50V 7pF (UJ),50V 0.0047 µF,50V 0.022 µF,25V 0.001 µF,50V 0.022 µF,25V 10 pF (CH),50V 33 pF,50V 6 pF (UJ),50V 22 pF (CH),50V 100 pF,50V 10 µF,16V,Electrolytic 0.022 µF,25V 5 pF,50V 18 pF (CH),50V 0.022 µF,25V 12 pF (CH),50V 0.047 µF,25V 0.022 µF,50V 27 pF (UJ),50V 560 pF,50V 0.022 µF,50V 33 pF,50V 0.001 µF,50V 0.022 µF,25V 10 µF,16V,Electrolytic 0.022 µF,25V 22 pF,50V 0.001 µF,50V 2.2 µF,50V,Electrolytic 1 µF,50V,Electrolytic 0.022 µF,25V 3.3 µF,50V,Electrolytic C363 C364 C365 C366 C367,368 C369 C370 C371,372 C373,374 C380 C381 C382 C383 C384 C385 C386 C387 C391 C392 C393 C394 C395 C396 C397 C398 C399 C401~404 C407,408 C411 C412 C413 C414 C415,416 C417,418 C419,420 C421~424 C425,426 C429 C430 C431~433 C601 C602 C603 C613~616 C620 C621 C622 C624 C625 C626 C627 C628 C629 C630 C639,640 1 C651 1 C654 1 C657~660 C665 C683 C688 C689 C701,702 C703 C704 C705 C710 C711 C712 C713 C714 C715 C801 C802 C803 C804 C805 C806 C807 C809 C810 C811 –2– PRICE RANK PARTS CODE VCKYCY1EF223Z RC-GZA106AF1C VCKYCY1EF223Z VCKYCY1HB102K RC-EZD105AF1H VCCSCY1HL560J RC-GZA105AF1H RC-EZD105AF1H VCTYPA1CX183K RC-GZA106AF1C VCCCCY1HH120J VCCCCY1HH150J VCKYCY1EF223Z VCKYCY1HB102K VCKYPA1HF103Z VCKYPA1HB331K VCKYCY1EF223Z RC-GZA476AF1C VCKYCY1HB102K RC-GZA105AF1H RC-GZA476AF1C VCKYCY1EF223Z RC-GZA107AF1A VCKYCY1EF223Z RC-GZA107AF1A VCKYPA1HF223Z RC-GZA106AF1C RC-GZA106AF1C VCKYPA1HB331K VCKYPA1HB331K VCKYPA1HB472K VCKYPA1HB221K RC-GZA106AF1C RC-GZA225AF1H VCKYCY1HB272K RC-QZA104AFYJ RC-GZA106AF1C RC-GZA336AF1C RC-GZA107AF1C VCKYCY1HB221K VCKYCY1EF473Z RC-GZA476AF1C RC-GZA336AF1C VCFYFA1HA104J RC-GZV477AF1E RC-GZA107AF1E VCKYPA1HF223Z VCKYPA1HF223Z RC-GZA106AF1C RC-GZA107AF1E VCKYPA1HF223Z RC-GZA106AF1C RC-GZA475AF1E RC-GZW478AF1E VCKYPA1HB472K VCFYFA1HA104J VCFYFA1HA104J VCFYFA1HA104J VCFYFA1HA473J RC-GZW228AF1V VCFYFA1HA473J RC-GZA474AF1H VCCCCY1HH220J VCKYCY1EF104Z VCKYCY1EF223Z VCKYPA1HF103Z VCKYCY1EB103K RC-GZA335AF1H VCKYCY1EB103K RC-GZA106AF1C VCKYCY1HB561K RC-GZA107AF1A VCCSCY1HL101J VCKYCY1EB153K RC-EZD476AF1A VCKYCY1EB103K VCKYCY1HB272K VCKYCY1HB472K VCKYCY1EB333K VCKYCY1HB472K VCKYCY1HB102K RC-GZA476AF1A J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AB AB AB AA AB AD AB AB AA AB AA AA AB AA AB AA AB AB AA AB AB AB AB AB AB AB AB AB AA AA AB AA AB AB AA AC AB AB AB AA AB AB AB AC AC AB AB AB AB AB AB AB AB AG AB AC AC AC AB AF AB AA AA AA AB AB AA AB AA AB AA AB AA AA AC AA AA AA AC AA AA AB DESCRIPTION 0.022 µF,25V 10 µF,16V,Electrolytic 0.022 µF,25V 0.001 µF,50V 1 µF,50V,Electrolytic 56 pF,50V 1 µF,50V,Electrolytic 1 µF,50V,Electrolytic 0.018 µF,16V 10 µF,16V,Electrolytic 12 pF (CH),50V 15 pF (CH),50V 0.022 µF,25V 0.001 µF,50V 0.01 µF,16V 330 pF,50V 0.022 µF,25V 47 µF,16V,Electrolytic 0.001 µF,50V 1 µF,50V,Electrolytic 47 µF,16V,Electrolytic 0.022 µF,25V 100 µF,10V,Electrolytic 0.022 µF,25V 100 µF,10V,Electrolytic 0.022 µF,50V 10 µF,16V,Electrolytic 10 µF,16V,Electrolytic 330 pF,50V 330 pF,50V 0.0047 µF,50V 220 pF,50V 10 µF,16V,Electrolytic 2.2 µF,50V,Electrolytic 0.0027 µF,50V 0.1 µF,50V,Mylar 10 µF,16V,Electrolytic 33 µF,16V,Electrolytic 100 µF,16V,Electrolytic 220 pF,50V 0.047 µF,25V 47 µF,16V,Electrolytic 33 µF,16V,Electrolytic 0.1 µF,50V,Thin Film 470 µF,25V,Electrolytic 100 µF,25V,Electrolytic 0.022 µF,50V 0.022 µF,50V 10 µF,16V,Electrolytic 100 µF,25V,Electrolytic 0.022 µF,50V 10 µF,16V,Electrolytic 4.7 µF,25V,Electrolytic 4700 µF,25V,Electrolytic 0.0047 µF,50V 0.1 µF,50V,Thin Film 0.1 µF,50V,Thin Film 0.1 µF,50V,Thin Film 0.047 µF,50V,Thin Film 2200 µF,35V,Electrolytic 0.047 µF,50V,Thin Film 0.47 µF,50V,Electrolytic 22 pF (CH),50V 0.1 µF,25V 0.022 µF,25V 0.01 µF,50V 0.01 µF,25V 3.3 µF,50V,Electrolytic 0.01 µF,25V 10 µF,16V,Electrolytic 560 pF,50V 100 µF,10V,Electrolytic 100 pF,50V 0.015 µF,25V 47 µF,10V,Electrolytic 0.01 µF,25V 0.0027 µF,50V 0.0047 µF,50V 0.033 µF,25V 0.0047 µF,50V 0.001 µF,50V 47 µF,10V,Electrolytic XL-3000V NO. C812 C813 C817~819 C820 C821 C822 C823 C824,825 C826,827 C828 C829 C830 C835 C836 C837 C838 C839 C840,841 C842 C843 C844 C845 C846,847 C848 C849 C850 C851 C852 C853 C855 C857 C858 C859 C860 C862 C863 C864~869 C870 C871 C872 C887 C892,893 C901,902 C903,904 C905,906 PRICE RANK PARTS CODE VCKYCY1EF103Z RC-EZD107AF1A VCKYCY1EB104K VCKYCY1EF103Z VCKYCY1EB104K RC-GZA227AF1A VCKYCY1EF103Z VCKYCY1EB563K VCCCCY1HH150J RC-GZA107AF1A RC-EZD107AF1A VCKYCY1EB563K VCKYCY1EB563K RC-GZA107AF1A VCKYCY1HB471K RC-EZD476AF1A VCCSCY1HL2R0C RC-GZA107AF1A RC-GZA476AF1A VCKYCY1EF104Z VCKYCY1HB682K RC-GZA107AF1A VCKYCY1EF104Z VCCSCY1HL390J VCKYCY1EB563K RC-GZA227AF1A RC-EZD107AF1A VCQYKA1HM222J VCKYPA1HB472K RC-GZA107AF1A RC-GZA476AF1C VCKYCY1EF103Z RC-GZA477AF1A VCKYCY1EF104Z VCKYPA1HB102K VCKYCY1HB471K VCKYCY1HB221K VCKYPA1HB102K RC-EZD476AF1C VCKYCY1EB104K VCKYCY1HB272K RC-EZD476AF1C RC-GZV227AF1H RC-EZ0002SJZZ RC-GZA107AF1A DESCRIPTION J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AB AD AA AD AB AA AD AA AB AB AD AD AB AA AC AD AB AB AA AA AB AA AD AD AB AB AB AB AB AB AA AC AA AA AA AA AA AC AD AA AC AC AD AB 0.01 µF,25V 100 µF,10V,Electrolytic 0.1 µF,25V 0.01 µF,25V 0.1 µF,25V 220 µF,10V,Electrolytic 0.01 µF,25V 0.056 µF,25V 15 pF (CH),50V 100 µF,10V,Electrolytic 100 µF,10V,Electrolytic 0.056 µF,25V 0.056 µF,25V 100 µF,10V,Electrolytic 470 pF,50V 47 µF,10V,Electrolytic 2 pF,50V 100 µF,10V,Electrolytic 47 µF,10V,Electrolytic 0.1 µF,25V 0.0068 µF,50V 100 µF,10V,Electrolytic 0.1 µF,25V 39 pF,50V 0.056 µF,25V 220 µF,10V,Electrolytic 100 µF,10V,Electrolytic 0.0022 µF,50V,Mylar 0.0047 µF,50V 100 µF,10V,Electrolytic 47 µF,16V,Electrolytic 0.01 µF,25V 470 µF,10V,Electrolytic 0.1 µF,25V 0.001 µF,50V 470 pF,50V 220 pF,50V 0.001 µF,50V 47 µF,16V,Electrolytic 0.1 µF,25V 0.0027 µF,50V 47 µF,16V,Electrolytic 220 µF,50V,Electrolytic 10 µF,50V,Electrolytic 100 µF,10V,Electrolytic J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 0 ohm,Jumper,0.8×1.55mm,Green 4.7 kohms,1/16W 4.7 kohms,1/16W 4.7 kohms,1/16W 1 kohm,1/16W 1 kohm,1/16W 100 kohm,1/16W 100 ohm,1/4W 120 ohms,1/16W 10 kohm,1/16W 1 kohm,1/16W 1 kohm,1/16W 82 ohms,1/16W 3.3 kohms,1/6W 10 kohm,1/16W 82 kohms,1/16W 68 kohms,1/16W 82 kohms,1/16W 82 kohms,1/16W 82 kohms,1/16W 68 kohms,1/6W 4.7 kohms,1/16W 4.7 kohms,1/16W 4.7 kohms,1/16W 0 ohm,Jumper,0.8×1.55mm,Green 4.7 kohms,1/16W 4.7 kohms,1/16W 4.7 kohms,1/16W 39 kohms,1/16W 100 kohm,1/16W 1 kohm,1/16W 6.8 kohms,1/16W 56 kohms,1/6W 10 kohm,1/16W RESISTORS R01AV~03AV R06AV~12AV R5V R7A0 R7A1 R7A2 R7A3 R7A4 R7A5 R7A6 R7A7 R7A8 R7A9 R7B0 R80A R80B R80C R80E R80F R80G R91V R93V R94AV R94BV R97V R98V R100V R101,102 R101V,102V R103 R103V R104 R104V VRS-CY1JB000J VRS-CY1JB472J VRS-CY1JB472J VRS-CY1JB472J VRS-CY1JB102J VRS-CY1JB102J VRS-CY1JB104J VRD-ST2EE101J VRS-CY1JB121J VRS-CY1JB103J VRS-CY1JB102J VRS-CY1JB102J VRS-CY1JB820J VRD-ST2CD332J VRS-CY1JB103J VRS-CY1JB823J VRS-CY1JB683J VRS-CY1JB823J VRS-CY1JB823J VRS-CY1JB823J VRD-ST2CD683J VRS-CY1JB472J VRS-CY1JB472J VRS-CY1JB472J VRS-CY1JB000J VRS-CY1JB472J VRS-CY1JB472J VRS-CY1JB472J VRS-CY1JB393J VRS-CY1JB104J VRS-CY1JB102J VRS-CY1JB682J VRD-ST2CD563J VRS-CY1JB103J NO. R105,106 R105V R107V,108V R108 R109 R110 R111 R111V R112V 1 R113,114 R113V R114V R115 R115V,116V R118 R119 R120 R121 R121V R122 R123 R123V R124 R124V R125,126 R137V R138V R139V~141V R142V R143V R156V R157V~159V R160V R161V R162V R163V R164V,165V R166V~169V R170V R171V R178V R181V~184V R185V~190V R193V R194V R195V R201 R202 R203,204 R205,206 R207 R208 R209 R210 R211 R212 R213~216 R217 R218 R301 R302 R303 R304 R305 R306 R307 R308 R309 R310 R312 R313 R314,315 R316 R323 R336 R350 R351 R352 R353 R355 R356 R357 –3– PARTS CODE VRD-ST2EE471J VRS-CY1JB472J VRS-CY1JB103J VRD-ST2CD102J VRD-ST2CD223J VRS-CY1JB102J VRD-ST2CD102J VRS-CY1JB222J VRS-CY1JB560J VRG-ST2EC101J VRS-CY1JB101J VRS-CY1JB682J VRD-ST2CD563J VRS-CY1JB153J VRD-ST2EE473J VRS-CY1JB333J VRS-CY1JB102J VRS-CY1JB103J VRS-CY1JB332J VRS-CY1JB102J VRD-ST2EE103J VRS-CY1JB750J VRS-CY1JB473J VRS-CY1JB221J VRS-VV3LA681J VRS-CY1JB102J VRS-CY1JB330J VRS-CY1JB102J VRS-CY1JB330J VRS-CY1JB221J VRS-CY1JB472J VRS-CY1JB821J VRS-CY1JB472J VRS-CY1JB330J VRS-CY1JB472J VRS-CY1JB330J VRS-CY1JB100J VRS-CY1JB330J VRS-CY1JB472J VRS-CY1JB104J VRS-CY1JB820J VRS-CY1JB104J VRS-CY1JB103J VRS-CY1JB472J VRS-CY1JB271J VRS-CY1JB101J VRD-ST2CD822J VRS-CY1JB822J VRS-CY1JB104J VRS-CY1JB103J VRD-ST2CD473J VRD-ST2EE331J VRS-CY1JB103J VRD-ST2CD103J VRS-CY1JB272J VRD-ST2CD272J VRS-CY1JB123J VRD-ST2CD123J VRS-CY1JB123J VRD-ST2EE220J VRS-CY1JB104J VRD-ST2CD333J VRS-CY1JB473J VRS-CY1JB681J VRS-CY1JB100J VRD-ST2EE470J VRS-CY1JB103J VRD-ST2EE471J VRS-CY1JB472J VRS-CY1JB222J VRS-CY1JB681J VRS-CY1JB330J VRS-CY1JB331J VRS-CY1JB683J VRD-ST2CD562J VRS-CY1JB272J VRS-CY1JB562J VRS-CY1JB102J VRS-CY1JB271J VRS-CY1JB332J VRS-CY1JB102J VRS-CY1JB474J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J PRICE RANK DESCRIPTION AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 470 ohms,1/4W 4.7 kohms,1/16W 10 kohm,1/16W 1 kohm,1/6W 22 kohms,1/6W 1 kohm,1/16W 1 kohm,1/6W 2.2 kohms,1/16W 56 ohms,1/16W 100 ohm,1/4W,Fusible 100 ohm,1/16W 6.8 kohms,1/16W 56 kohms,1/6W 15 kohms,1/16W 47 kohms,1/4W 33 kohms,1/16W 1 kohm,1/16W 10 kohm,1/16W 3.3 kohms,1/16W 1 kohm,1/16W 10 kohm,1/4W 75 ohms,1/16W 47 kohms,1/16W 220 ohms,1/16W 680 ohms,3W,Metal Oxide Film 1 kohm,1/16W 33 ohms,1/16W 1 kohm,1/16W 33 ohms,1/16W 220 ohms,1/16W 4.7 kohms,1/16W 820 ohms,1/16W 4.7 kohms,1/16W 33 ohms,1/16W 4.7 kohms,1/16W 33 ohms,1/16W 10 ohm,1/16W 33 ohms,1/16W 4.7 kohms,1/16W 100 kohm,1/16W 82 ohms,1/16W 100 kohm,1/16W 10 kohm,1/16W 4.7 kohms,1/16W 270 ohms,1/16W 100 ohm,1/16W 8.2 kohms,1/6W 8.2 kohms,1/16W 100 kohm,1/16W 10 kohm,1/16W 47 kohms,1/6W 330 ohms,1/4W 10 kohm,1/16W 10 kohm,1/6W 2.7 kohms,1/16W 2.7 kohms,1/6W 12 kohms,1/16W 12 kohms,1/6W 12 kohms,1/16W 22 ohms,1/4W 100 kohm,1/16W 33 kohms,1/6W 47 kohms,1/16W 680 ohms,1/16W 10 ohm,1/16W 47 ohms,1/4W 10 kohm,1/16W 470 ohms,1/4W 4.7 kohms,1/16W 2.2 kohms,1/16W 680 ohms,1/16W 33 ohms,1/16W 330 ohms,1/16W 68 kohms,1/16W 5.6 kohms,1/6W 2.7 kohms,1/16W 5.6 kohms,1/16W 1 kohm,1/16W 270 ohms,1/16W 3.3 kohms,1/16W 1 kohm,1/16W 470 kohms,1/16W XL-3000V NO. R358 R359 R360 R361,362 R363 R364 R365 R366 R371~374 R376 R377 R379 R380 R381 R382 R383 R384 R385 R386 R387 R391,392 R393 R395 R401,402 R403,404 R405,406 R407,408 R415~418 R421,422 R423~425 R437,438 R439,440 R603,604 R607 R608,609 R610 R611 R612 R613 R614 R617 R619,620 R621 R623,624 R628 R629 R634 R637,638 R661,662 R685 R686 R687 R688 R689 R702 R706 R707 R708 R710 R711 R718 R719 R720A,B R721,722 R723 R725 R727 R728 R729 R731~735 R738~742 R744 R749,750 R751 R755 R757,758 R759 R760~766 R768 R769~771 R772,773 R776,777 PRICE RANK PARTS CODE VRS-CY1JB822J VRS-CY1JB182J VRS-CY1JB472J VRS-CY1JB562J VRD-ST2CD332J VRS-CY1JB332J VRS-CY1JB103J VRS-CY1JB222J VRS-CY1JB102J VRD-ST2CD103J VRD-ST2CD562J VRS-CY1JB222J VRD-ST2CD152J VRS-CY1JB103J VRD-ST2EE331J VRS-CY1JB562J VRD-ST2CD682J VRD-ST2CD562J VRD-ST2EE331J VRD-ST2CD562J VRD-ST2EE391J VRS-CY1JB102J VRD-ST2CD473J VRS-CY1JB102J VRS-CY1JB182J VRD-ST2CD273J VRD-ST2CD272J VRS-CY1JB102J VRS-CY1JB102J VRD-ST2CD102J VRS-CY1JB682J VRS-CY1JB392J VRS-CY1JB103J VRS-CY1JB682J VRS-CY1JB102J VRD-ST2EE470J VRD-ST2EE101J VRD-ST2EE821J VRS-CY1JB472J VRD-ST2EE470J VRD-ST2CD333J VRD-ST2EE470J VRS-CY1JB223J VRS-CY1JB223J VRD-ST2EE101J VRD-ST2EE821J VRD-ST2EE332J VRD-ST2EE4R7J VRD-ST2EE331J VRD-ST2CD103J VRD-ST2CD473J VRD-RT2HD272J VRD-ST2CD102J VRD-ST2EE102J VRS-CY1JB103J VRS-CY1JB392J VRS-CY1JB272J VRS-CY1JB222J VRS-CY1JB272J VRS-CY1JB122J VRS-CY1JB152J VRS-CY1JB122J VRS-CY1JB122J VRS-CY1JB103J VRS-CY1JB473J VRS-CY1JB103J VRS-CY1JB473J VRS-CY1JB102J VRS-CY1JB473J VRS-CY1JB102J VRS-CY1JB102J VRD-ST2CD102J VRS-CY1JB102J VRD-ST2CD102J VRS-CY1JB102J VRS-CY1JB102J VRD-ST2CD102J VRS-CY1JB102J VRS-CY1JB102J VRD-ST2CD102J VRS-CY1JB102J VRS-CY1JB102J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA DESCRIPTION NO. 8.2 kohms,1/16W 1.8 kohms,1/16W 4.7 kohms,1/16W 5.6 kohms,1/16W 3.3 kohms,1/6W 3.3 kohms,1/16W 10 kohm,1/16W 2.2 kohms,1/16W 1 kohm,1/16W 10 kohm,1/6W 5.6 kohms,1/6W 2.2 kohms,1/16W 1.5 kohms,1/6W 10 kohm,1/16W 330 ohms,1/4W 5.6 kohms,1/16W 6.8 kohms,1/6W 5.6 kohms,1/6W 330 ohms,1/4W 5.6 kohms,1/6W 390 ohms,1/4W 1 kohm,1/16W 47 kohms,1/6W 1 kohm,1/16W 1.8 kohms,1/16W 27 kohms,1/6W 2.7 kohms,1/6W 1 kohm,1/16W 1 kohm,1/16W 1 kohm,1/6W 6.8 kohms,1/16W 3.9 kohms,1/16W 10 kohm,1/16W 6.8 kohms,1/16W 1 kohm,1/16W 47 ohms,1/4W 100 ohm,1/4W 820 ohms,1/4W 4.7 kohms,1/16W 47 ohms,1/4W 33 kohms,1/6W 47 ohms,1/4W 22 kohms,1/16W 22 kohms,1/16W 100 ohm,1/4W 820 ohms,1/4W 3.3 kohms,1/4W 4.7 ohms,1/4W 330 ohms,1/4W 10 kohm,1/6W 47 kohms,1/6W 2.7 kohms,1/2W 1 kohm,1/6W 1 kohm,1/4W 10 kohm,1/16W 3.9 kohms,1/16W 2.7 kohms,1/16W 2.2 kohms,1/16W 2.7 kohms,1/16W 1.2 kohms,1/16W 1.5 kohms,1/16W 1.2 kohms,1/16W 1.2 kohms,1/16W 10 kohm,1/16W 47 kohms,1/16W 10 kohm,1/16W 47 kohms,1/16W 1 kohm,1/16W 47 kohms,1/16W 1 kohm,1/16W 1 kohm,1/16W 1 kohm,1/6W 1 kohm,1/16W 1 kohm,1/6W 1 kohm,1/16W 1 kohm,1/16W 1 kohm,1/6W 1 kohm,1/16W 1 kohm,1/16W 1 kohm,1/6W 1 kohm,1/16W 1 kohm,1/16W R778~781 R782 R783 R785 R792 R793 R795 R796 R797 R798 R799 R801 R802 R804 R806 R807 R808 R809 R810 R811 R812 R813 R814 R819 R820 R821 R822 R823 R824 R825 R826 R827 R828 R829 R830 R831~837 R843 R851 R852~855 R861~863 R864,865 R866 R867 R868 R870 R873 R874 R876 R877 R879 R880 R881 R882 R883,884 R885 R887 R888 R901 R902 R904 R905 R910 R911 R912 1 R913 R914 PRICE RANK PARTS CODE VRS-CY1JB473J VRS-CY1JB102J VRS-CY1JB333J VRS-CY1JB102J VRS-CY1JB473J VRS-CY1JB103J VRD-ST2CD473J VRD-ST2EE102J VRS-CY1JB222J VRS-CY1JB472J VRD-ST2EE102J VRD-ST2CD103J VRS-CY1JB473J VRS-CY1JB104J VRS-CY1JB153J VRS-CY1JB103J VRS-CY1JB332J VRS-CY1JB103J VRS-CY1JB332J VRS-CY1JB222J VRS-CY1JB332J VRD-ST2EE100J VRS-CY1JB332J VRD-ST2CD221J VRS-CY1JB102J VRD-ST2CD151J VRD-ST2EE330J VRD-ST2CD102J VRS-CY1JB473J VRS-CY1JB823J VRS-CY1JB272J VRS-CY1JB393J VRS-CY1JB122J VRD-ST2CD683J VRD-ST2CD102J VRS-CY1JB102J VRD-ST2CD102J VRS-CY1JB331J VRS-CY1JB104J VRS-CY1JB222J VRD-ST2CD273J VRD-ST2CD472J VRS-CY1JB332J VRS-CY1JB273J VRS-CY1JB333J VRD-ST2CD332J VRS-CY1JB222J VRS-CY1JB154J VRS-CY1JB683J VRS-CY1JB332J VRS-CY1JB332J VRS-CY1JB474J VRS-CY1JB682J VRD-ST2EE8R2J VRS-CY1JB223J VRS-CY1JB223J VRD-ST2CD103J VRS-CY1JB222J VRS-CY1JB473J VRS-CY1JB222J VRS-CY1JB473J VRD-ST2EE272J VRD-ST2EE101J VRD-ST2EE471J VRG-ST2EM100J VRD-ST2CD471J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J DESCRIPTION AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 47 kohms,1/16W 1 kohm,1/16W 33 kohms,1/16W 1 kohm,1/16W 47 kohms,1/16W 10 kohm,1/16W 47 kohms,1/6W 1 kohm,1/4W 2.2 kohms,1/16W 4.7 kohms,1/16W 1 kohm,1/4W 10 kohm,1/6W 47 kohms,1/16W 100 kohm,1/16W 15 kohms,1/16W 10 kohm,1/16W 3.3 kohms,1/16W 10 kohm,1/16W 3.3 kohms,1/16W 2.2 kohms,1/16W 3.3 kohms,1/16W 10 ohm,1/4W 3.3 kohms,1/16W 220 ohms,1/6W 1 kohm,1/16W 150 ohms,1/6W 33 ohms,1/4W 1 kohm,1/6W 47 kohms,1/16W 82 kohms,1/16W 2.7 kohms,1/16W 39 kohms,1/16W 1.2 kohms,1/16W 68 kohms,1/6W 1 kohm,1/6W 1 kohm,1/16W 1 kohm,1/6W 330 ohms,1/16W 100 kohm,1/16W 2.2 kohms,1/16W 27 kohms,1/6W 4.7 kohms,1/6W 3.3 kohms,1/16W 27 kohms,1/16W 33 kohms,1/16W 3.3 kohms,1/6W 2.2 kohms,1/16W 150 kohms,1/16W 68 kohms,1/16W 3.3 kohms,1/16W 3.3 kohms,1/16W 470 kohms,1/16W 6.8 kohms,1/16W 8.2 ohms,1/4W 22 kohms,1/16W 22 kohms,1/16W 10 kohm,1/6W 2.2 kohms,1/16W 47 kohms,1/16W 2.2 kohms,1/16W 47 kohms,1/16W 2.7 kohms,1/4W 100 ohm,1/4W 470 ohms,1/4W 10 ohm,1/4W,Fusible AA 470 ohms,1/6W OTHER CIRCUITRY PARTS CFW451,452 CFW701A,B CFW852 CNP307 CNP601,602 CNP607 CNP608 1 CNP651 CNP652 CNP653 CNP701 CNP702 CNP703 –4– QCNWN0308SJZZ QCNWN0292SJZZ QCNWN0303SJZZ QCNCM010LAWZZ QCNCM999CAFZZ QCNCM999CAFZZ QCNCM004BAFZZ QCNCM041ESJZZ QCNCM998BAFZZ QCNCM998BAFZZ QCNCM999BAFZZ QCNCM999KAFZZ QCNCM999NAFZZ J J J J J J J J J J J J J AB AD AB AC AG AG AB AE AC AC AD Lead Wire Flat Wire,3Pin Lead Wire Plug,11Pin Plug,3Pin Plug,3Pin Plug,2Pin Plug,5Pin Plug,2Pin Plug,2Pin Plug,2Pin Plug,10Pin AC Plug,13Pin XL-3000V NO. PRICE RANK PARTS CODE CNP707 QCNCM998DAFZZ CNP801 QCNCM037ESJZZ CNP801V QCNCW010MSJZZ CNP802 QCNCW007RSJZZ CNP802A QCNCM999HAFZZ CNP803 QCNCM035FSJZZ CNP804 QCNCM038BSJZZ CNP804V QCNCM015GSJZZ CNP805 QCNCM004CAFZZ CNP806 QCNCM999CAFZZ CNP807 QCNCM999BAFZZ CNP810 QCNCM999BAFZZ CNS307 QCNCW010LAWZZ CNS801 QCNCW010MSJZZ CNW3 QCNWN0288SJZZ CNW601,602 QCNWN0326SJZZ CNW607/CNS607 QCNWN0291SJZZ CNW608/CNS608 QCNWN0314SJZZ CNW653 QCNWN0331SJZZ CNW701/CNS701 QCNWN0271SJZZ CNW702/CNS702 QCNWN0311SJZZ CNW703A/CNS703QCNWN0332SJZZ CNW704/CNS704 QCNWN0324SJZZ CNW707/CNS707/CNS652 QCNWN0301SJZZ CNW801 QCNWN0312SJZZ CNW802V/CNS802QCNWN0313SJZZ CNW803/CNS803 QCNWN0276SJZZ CNW804/CNS804 QCNWN0290SJZZ CNW805/CNS805 QCNWN0296SJZZ CNW806/CNS806 QCNWN0270SJZZ CNW807/CNS807 QCNWN0271SJZZ 1 F651,652 QFS-D322ABGNI 1 F653 QFS-D162ABGNI 1 F654 QFS-T202BSJNO J601 QJAKM0001SJZZ J801 VHPPLT130T2-1 LCD701 RV-LX0012SJZZ LMP701 RLMPP0001SJZZ M801 RMOTV0004SJM1 M802 RMOTV0006SJZZ NM801 RMOTV0409AFM1 NM802 RMOTV0408SJM1 NSW801 QSW-F9001AWZZ 1 RLY601 RRLYD0004SJZZ RX701 VHLN64H380A-1 SO301 QTANC9003SJZZ SO401 QSOCJ0302SJZZ SO601 QTANA0007SJZZ 1 SO655 QSOCA0212AWZZ 1 SW651 QSOCE0008AWZZ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J SW709 SW710 QSW-K0004SJZZ QSW-K0004SJZZ J J SW711 SW712 QSW-K0004SJZZ QSW-K0004SJZZ J J SW713 SW718 SW721 SW722 SW725 QSW-K0004SJZZ QSW-K0004SJZZ QSW-K0004SJZZ QSW-K0004SJZZ QSW-K0004SJZZ J J J J J SW726 QSW-K0004SJZZ J SW727 SW802 QSW-K0004SJZZ QSW-B0001SJZZ J J DESCRIPTION AB Plug,4Pin AD Plug,5Pin Plug,12Pin AF Socket,16Pin AD Plug,8Pin AD Plug,6Pin AB Plug,2Pin AB Plug,7Pin AB Plug,3Pin AG Plug,3Pin AD Plug,2Pin AD Plug,2Pin AD Socket,11Pin Socket,12Pin AE Flat Cable,16Pin Connector Ass’y,3Pin AE Connector Ass’y,3/3Pin Connector Ass’y,2/2Pin Connector Ass’y,2Pin AD Connector Ass’y,2/2Pin Connector Ass’y,10/10Pin Connector Ass’y,13/13Pin Connector Ass’y,7/7Pin AD Connector Ass’y,3/4/2Pin Flat Cable,12Pin Connector Ass’y,9/8Pin AE Connector Ass’y,6/6Pin AD Connector Ass’y,2Pin AE Connector Ass’y,3/3Pin AE Connector Ass’y,3/3Pin AD Connector Ass’y,2/2Pin AE Fuse,T3.15A L 250V Fuse,T1.6A L 250V Temperature Fuse,2A,250V AG Jack,Headphones AM Jack,CD Degital Output AR LCD Display AT Lamp AM Motor with Gear [CD Lid] AP Fan Motor AN Motor with Gear [Sled] AR Motor with Chassis [Spindle] AE Switch,Push Type [Pickup In] AG Relay AK Remote Sensor AF Terminal,Antenna AE Socket,Video/AUX Input/Video Out AF Terminal,Speaker AD Socket AC Input AH Switch,Rotary Type [Voltage Selector] AD Switch,Key Type [On/Stand-by] AD Switch,Key Type [CD Lid Open/Close] AD Switch,Key Type [FF/Preset Up] AD Switch,Key Type [CD Play/Pause/Tuning Up] AD Switch,Key Type [Volume Up] AD Switch,Key Type [Volume Down] AD Switch,Key Type [Memory/Set] AD Switch,Key Type [Bass/Treble] AD Switch,Key Type [CD Stop/Tuning Down] AD Switch,Key Type [REW/Preset Down] AD Switch,Key Type [Function] AG Switch,Lever Type [CD Lid] CD MECHANISM PARTS 301 302 303 304 305 306 307 1 308 308- 1 308- 2 308- 3 NGERH0586AFZZ NGERH0587AFZZ MLEVP0010AWZZ NSFTM0291AFFW PCOVP1333AFSA PCUSG0001AWSA PCUSG0004AWSA DCTRH8005SJ01 ———— J J J J J J J J NGERR0043AFZZ MSPRC0961AFZZ J J AC AC AC AD AF AD AD BA — Gear,Middle Gear,Drive Rail,Guide Shaft,Guide Cover,Mechanism Cushion (Green) Cushion (Red-Brown) Pickup Unit Ass’y Pickup Unit (Not Replacement Item) AC Gear,Rack AA Spring,Rack NO. 701 702 703 704 NM801 NM802 NSW801 PRICE RANK PARTS CODE LX-WZ1070AFZZ XBBSD20P03000 XBSSD26P06000 XHBSD20P05000 RMOTV0409AFM1 RMOTV0408SJM1 QSW-F9001AWZZ J J J J J J J AA AA AA AA AN AR AE DESCRIPTION Washer,ø1.5×ø3.8×0.25mm Screw,ø2×3mm Screw,ø2.6×6mm Screw,ø2×5mm Motor with Gear [Sled] Motor with Chassis [Spindle] Switch,Push Type [Pickup In] CABINET PARTS 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 228 229 230 231 232 233 234 235 236 237 238 239 240 GCABA1073SJSA GCABB1066SJSA GCOVA1013SJSA GCOVA1005SJSA GFTAT1008SJSA LANGQ0002SJFW HDECQ0060SJSA HDECQ0051SJSA JKNBZ0053SJSA JKNBZ0054SJSA LANGF0033SJFW LANGF0034SJFW LANGF0035SJFW LANGK0025SJFW LANGK0026SJFW LCHSM0014SJFW LHLDW1001SJZZ LHLDZ1033SJSA LHLDZ1034SJSA LHLDZ1035SJSA LHLDZ1036SJSA LPLTP0001SJSA MLEVP0006SJSA MLEVP0007SJSA NGERW0004SJSA NGERW0005SJSA NGERW0006SJSA PCOVU9002SJZZ PCOVZ1005SJSA PCUSG0003SJZZ PGUMS0002SJZZ PRDAR0051SJFW PRDAR0038SJFW PREFL0001SJSA PSHEP0003SJZZ PSHEP0004SJZZ QFSHD0001AWZZ TLABS0004SJZZ TLABS0036SJZZ TSPC-0254SJZZ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 240 TSPC-0271SJZZ J 240 TSPC-0282SJZZ J 241 242 243 244 245 246 247 248 249 250 251 252 601 602 603 604 605 606 607 608 609 610 611 612 613 615 PCOVS3005SJFW PRDAR0048SJFW LANGF0037SJFW LANGK0029SJFW LANGK0028SJFW PCOVP1003SJZZ PCOVP1004SJZZ PSPAH0001SJZZ PCOVM3001SJFW PCOVU9001SJZZ PCOVU9001SJZZ LX-WZ9005SJZZ LX-EZ0001SJFN LX-WZ7094AFZZ XEBSD25P08000 XEBSD25P10000 XEBSD25P12000 XEBSF25P08000 XHBSD20P05000 XHBSD30P06000 XHBSD40P08000 XJBSD30P06000 XJBSD30P08000 XJBSD30P10000 XJBSD30P14000 XJBSF30P10000 J J J J J J J J J J J J J J J J J J J J J J J J J J –5– AL AE AN AB AE AF AF AB AB AC AE AB AH AD AD AD AE AE AE AE AE AE AE AG AB AE AC AA AE AD AE AD AB AC AB AE AC AB AC AC AC AB AA AA AA AA AA AA AA AA AA AA AA AA AA Front Cabinet Bottom Cabinet Rear Panel Cover,Remote Sensor CD Lid Lug Clear Panel,CD Lid Clear Panel,Display Knob,Operation A Knob,Operation B Bracket,Main PWB Bracket,Tuner PWB Bracket,Gear Box Bracket,Tuner PWB Cover,Lamp Chassis Nylon Band LCD Holder,A LED Holder,A Gear Box Lid,Gear Box Cam Plate Rotate Lever,CD Lid,Left Rotate Lever,CD Lid,Right Drive Gear,A Drive Gear,B Drive Gear,C Felt,CD Lid Cover Indicator Panel Cushion,Leg Cushion,CD Lid Radiator,Main Radiator,Transistor LCD Diffusion Plate Sheet,LCD LCD Reflect Paper Holder,Fuse Label,Laser Label,Class 3A Label,Specification [Except for Thailand/Philippines] Label,Specification [For Thailand] Label,Specification [For Philippines] Plate,Shield Radiator,Sub Bracket,Fan Motor Bracket,Decode PWB Bracket,Decode PWB Shield Cover,Power PWB (A) Shield Cover,Power PWB (B) Felt Shield Cover Cover,Lamp Felt Thermo Shield Cover Screw,ø2.5×10mm Washer,Special Type Screw,ø2.5×8mm Screw,ø2.5×10mm Screw,ø2.5×12mm Screw,ø2.5×8mm Screw,ø2×5mm Screw,ø3×6mm Screw,ø4×8mm Screw,ø3×6mm Screw,ø3×8mm Screw,ø3×10mm Screw,ø3×14mm Screw,ø3×10mm XL-3000V NO. 616 617 618 619 620 621 622 623 PRICE RANK PARTS CODE XJBSF30P12000 XJPSF30P11000 XEBSD25P14000 XHBSD25P08000 XESSD25P12000 XWSSE03-01050 LX-JZ0001SJFD LX-WZ9006SJZZ J J J J J J J J AA AA AA AA AA AA AA DESCRIPTION NO. Screw,ø3×12mm Screw,ø3×11mm Screw,ø2.5×14mm Screw,ø2.5×8mm Screw,ø2.5×12mm Washer,ø3×5mm×0.1mm Screw,ø3×10mm Thermo Shield Washer,Special Type SPEAKER BOX PARTS 901 902 903 904 905 906 907 908 909 910 SP1,2 SP3,4 CPNLS1006SJ01 GBOXS0009SJSA GWAKP1016SJ01 PDUC-0001SJZZ PGUMM0003SJSA PSPAG0002SJZZ QTANA9011SJZZ TSPC-0221SJZZ HSY042SPK07 XTBSF40P12000 RSPA00005SJ6W RSPA00004SJ6T PRICE RANK PARTS CODE DESCRIPTION P.W.B. ASSEMBLY (Not Replacement Item) PWB-A1~8 1 PWB-B PWB-C PWB-D DCEKLV035SJ03 J DCEKJV035SJ03 QPWBF3895AFZZ DCEKS0005SJ03 J J J Main/Tuner/Display/Terminal/ Switch/Led/Lamp/Holder Power AC CD Motor (PWB Only) Video J AZ OTHER SERVICE PART J J J J J J J J J J J J AS AZ AM AE AD AD AE AD AE AA AQ AK Front Panel Ass’y Box Ass’y Net Flame Ass’y Duct Pipe Net Catcher Gasket Terminal Specification Label Capacitor,3.3 µF,50V (N.P.) Screw,ø4×12mm Woofer Tweeter UDSKA0004AFZZ ACCESSORIES/PACKING PARTS 1 ———— QACCA0001SJ00 J 1 QACCB0001SJ00 J 1 QACCE0001SJZZ J 1 QANTL0001SJZZ QANTW0002SJZZ QCNWH0005SJ01 QPLGA0250AFZZ J J J J 1 QPLGA0253AFZZ J SPAKA0058SJZZ SPAKA0059SJZZ SPAKA0068SJZZ J J J SPAKC0178SJZZ SPAKS0003SJZZ SPAKZ0008SJZZ SPAKZ0030SJZZ SPAKZ0040SJZZ SPAKZ0064SJZZ SSAKA0002SJZZ TGANE0002SJ15 TINSZ0103SJZZ J J J J J J J J J TINSZ0113SJZZ TLABE0105SJZZ J J TLABG0001SJZZ TLABG0044SJZZ J J TLABM0044SJZZ TLABN0140SJZZ TLABZ0009SJZZ J J J TLABZ0010SJZZ J TLABZ0011SJZZ J TLABZ0012SJZZ J TLABZ0015SJZZ TLABZ0019SJZZ TLSTS0004SJZZ J J J Z-SER-NO-LIST J RRMCG0030SJSA J GCABB1064SJSA J — Battery (Not Replacement Item) AS AC Power Supply Cord [For Saudi Arabia] AW AC Power Supply Cord [For Hong Kong] AH AC Power Supply Cord [Except for Saudi Arabia/Hong Kong] AK AM Loop Antenna AH FM Antenna Speaker Cord AF AC Plug Adapter [For Malaysia/ Philippines] AE AC Plug Adapter [For Saudi Arabia] AE Packing Add.,Left AE Packing Add.,Right Packing Add.,Speaker [Top/Bottom] Packing Case Sleeve Carton,Speaker Polyethylene Bag,Speaker AC Pad,Accessories AD Pad AC Polyethylene Bag,Unit AE Polyethylene Bag,Accessories Warranty Card [For Philippines] Operation Manual [Except for Thailand] Operation Manual [For Thailand] Label,Bar Code [For Union of Arab Emirates/ Hong Kong/ Thailand/ Philippines] AB Label,Hong Kong Label,Rated Input [For Hong Kong] AB Label,MP-3 Label,Serial No. AD Label,Made in China [For Syria] AD Label,Made in China [Except for Syria] AD Label,SHARP Japan [For Syria/ Union of Arab Emirates] AC Label,SHARP Corporation JAPAN [For Syria/Union of Arab Emirates] AC Label,VJ No. AC Label,M-I-C AB Service Station List [For Saudi Arabia] AC List,Serial No. Remote Control Battery Lid,Remote Control –6– CD Pickup Lens Cleaner Disc XL-3000V A 305 B 703 308 308-2 703 304 308-1 C 308-3 701 302 704x2 D 301 303 E 702x2 F NM802 307x2 306x2 NM801 G NSW801 H PWB-C 1 2 3 4 Figure 7 CD MECHANISM EXPLODED VIEW –7– 5 6 XL-3000V 601x2 A 222 206 219 604 228 207 M801 200 225 224 231x2 229 604 226 607 x2 PWB-A6 223 B 208 204 C 203 209 236 D z||y,y,{ z | { ,y,y|z{y, | 611x2 PWB-D PWB-A2 609x4 PWB-A8 Silicon Grease T651 611x7 615x2 616x3 611 211 232 205 245 603 241 611 210 215 613x2 237x6 213 611 242 622 F 604x2 246 Silicon Grease 611 610x3 604x2 PWB-A8 PWB-B Silicon Grease 233 E 602 620x4 603 217 612x2 611 249 PWB-A3 247 611 221 238 PWB-A7 250 235 604 212 214 234 619 PWB-A5 604x1 218 239 220 618 605x2 252 615x2 615x3 243 611x2 251 PWB-A4 M802 617x2 248 612x2 244x2 202 623x2 G PWB-A1 201 216 610 606x2 621 240 H 1 2 3 613 608x8 230x2 4 Figure 8 CABINET EXPLODED VIEW –8– 5 6 XL-3000V 908 902 A SP3,4 B 910x2 907 909 SP1,2 C 910x4 D Tweeter SP3 (L-CH) SP4 (R-CH) 901 Black 906 Capacitor 909 E White Line White Line 905x2 904 Black F Woofer SP1 (L-CH) SP2 (R-CH) G Tweeter SP3 (L-CH) SP4 (R-CH) 903 Woofer SP1 (L-CH) SP2 (R-CH) 905x2 H 1 2 Capacitor 3.3µF,50V (N.P) 909 3 4 5 6 Figure SPEAKER EXPLODED VIEW COPYRIGHT © 2001 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION AV Systems Group Audio Systems Division Higashihiroshima, Hiroshima 739-0192, Japan Printed in Japan A0108-1009SS•HA•C EX