Download Axxess ASWC Installation manual
Transcript
INSTALLATION INSTRUCTIONS ASWC-1 ASWC-1 Axxess Steering Wheel Control Interface Installation Manual US.PAT.NOS.8014920and8214105 Features OneInterfacedoesitall-Noadditionalinterfacesneeded Designedtobecompatiblewithallmajorradiobrands Autodetectsvehicletype,radioconnection,andpresetscontrols Abilitytodualassignsteeringwheelcontrolbuttons Canbemanuallyprogrammedformostvehicles Memoryretainssettingsevenafterbatterydisconnection orinterfaceremoval • Allconnectionsdoneattheradiolocation • Micro“B”USBupdatable InterFace components •ASWC-1Interface•12-pinharnesswithmale3.5mm connector•Female3.5mmconnectorwithBrownand Brown/Whitewires•12k-ohmresistor tools requIred •Cuttingtool•Crimpingtool•Tape METRA. THE WORLD’S BEST KITS.™ 1-800-221-0932 metraonline.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION REV. 3/27/2014 ASWC-INST10 • • • • • • Table of Contents Preface .............................................................................................. 3 Overview – IntroductiontotheASWC-1InterfaceandWiringHarness ..............4-5 ASWC-1 Installation – ConnectionstobeMade ................................................................6-7 – Programming.................................................................................8-9 AutoDetectMode:Overview........................................................ 8 AutoDetectMode:Steps ..........................................................8-9 – RemappingtheSWC(steeringwheelcontrol)Buttons ................10-11 ButtonAssignmentLegend ........................................................ 11 – ChangingRadioType .................................................................12-13 RadioLegend ............................................................................ 13 – DualAssignmentInstructions .....................................................14-15 DualAssignmentLegend ........................................................... 15 ASWC-1 Troubleshooting – AutoDetectMode ......................................................................16-18 – ManualProgrammingMode .......................................................19-21 ManualProgrammingLegend.................................................... 21 – ResettingOriginalASWC-1Settings ................................................ 22 – LEDFeedback............................................................................22-23 Caution: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. 2 Preface What you need to know before you begin 1) Knowthecorrectyear,make,andmodelofyourvehicle. 2) Ensurethesteeringwheelcontrolsworkbeforeremovingthefactory radio,andknowwhattheVolume Upbuttonis.TheVolume Up buttonisusedforprogramming,soknowingthisbeforeremoving theradioiscrucial. Note: Steering wheel controls must be the ones that came with the vehicle when purchased. We do not support custom work, i.e. adding a new steering wheel with added/new buttons. 3) GototheAxxesswebsite(axxessinterfaces.com)andclickonthe linkentitled“ASWC-1VehicleInstructions”,whichislocatedonthe rightsideofthescreeninthemiddle.Onceyouputyourvehicle informationin,clickthe“Submit”button.Thiswilltakeyouto anotherpage,whereyouwillthenclickonthelinkundertheword “Documents”.Thiswillprovidethevehiclespecificinstructions foryourvehicle.Printthisdocumentsoyouhaveitwithyouinthe vehicleduringtheinstallasitisthebest,andmostrecent sourceofinformation. 4) Besurethattheradioyouareinstallingiscompatiblewiththe ASWC-1.Additionally,refertotheRadioLegend(p.13)andyour radio’sownersmanual. 5) UpdatetheASWC-1tothelatestsoftware.Note: To update go to axxessinterfaces.com and download the WebXXpress program. Attention: Even though we have done extensive research and testing to verify that the steering wheel control wires we list are correct. It is your responsibility to verify the steering wheel control wires we list are correct with a multimeter. If you find an error, please notify our Axxess Tech department at 1-800-253-TECH. Please be in the vehicle, parked, along with access to the interface and vehicle wiring when you call. 3 Overview Introduction to the ASWC-1 Interface and Wiring Harness OnthetopoftheASWC-1interfacetherearethreepointsofinterest: 1) Programming LED 2) Reset Button 3) Update Port Cover(slidetoopen) Micro “B” USB UpdatePortCover ResetButton* *Note: The Reset button is recessed. An item, such as a partially unfolded paper clip, is needed to press the button. 4 ProgrammingLED Overview BelowarethewirecolorsfortheASWC-1.Pleasevisitthe Axxesswebsiteatwww.axxessinterfaces.comfordetailedinformation onyourspecificvehicleandforwhatcolorwire(s)tousewiththe ASWC-1interface. Pin-1 Pin-2 Pin-3 Pin-4 Pin-5 Pin-6 Pink White/Green Yellow/Green Green/Orange Gray/Red Black Pin-7 Blue/Pink Pin-8 Black/Green Pin-9 Red(tip of 3.5mm connector) Pin-10 White(ring of 3.5mm connector) Pin-11 Gray/Blue Pin-12 Red Shown below: Female 3.5mm connector with Brown (Br) and Brown/White (Br/W) wires. Br Shown above: 12-pin harness with male 3.5mm connector. Br/W 5 ASWC-1 Installation Connections to be made Onceyouhavecollectedorprintedoutthe“ASWC-1VehicleInstructions” foryourparticularvehicle,fromwww.axxessinterfaces.com,you’reready toinstalltheASWC-1. Note: If wiring is not available on our website for your vehicle, you will need to obtain this yourself. Please check first with Axxess Tech Support department at 1-800-253-TECH, as we may have this information. Into vehicle: 1) ConnecttheBlackwireoftheASWC-1totheground.Youmayuse thesamegroundingpointastheaftermarketradio;but it is highly recommended to ground the ASWC-1 to the chassis, of the vehicle, by itself. 2) Withthekeyintheoffposition,connecttheRedwireoftheASWC-1 tothe12-voltaccessorywire. 3) Locatethecorrectsteeringwheelcontrolwire(s)inthevehicle’s harness,asdescribedinthe“ASWC-1VehicleInstructions”.Connect thesewirestotheASWC-1. Note: Metra recommends that the wires are soldered for the best and most secure connection. Tapping style connectors are not recommended due to a higher chance of a intermittent connection or change in resistance values (which will cause the ASWC-1 to fail to program). Into radio: 1) Fortheradioslistedbelow,plugtheincludedfemale3.5mmadapter (withtheBrownandBrown/Whitewires)intothemale3.5mm connectoroftheASWC-1harness. A. For Eclipse radios:ConnecttheEclipsesteeringwheelcontrol wires(normallyBrownandBrown/Black)totheBrownand Brown/WhitewiresoftheASWC-1.TheBrownoftheASWC-1 goestotheBrown/BlackoftheEclipseandBrown/Whiteofthe ASWC-1goestotheBrownoftheEclipse. 6 ASWC-1 Installation Connections to be made B. For Metra OE radios:Connectthesteeringwheelcontrol Key1wire(Gray)totheBrownwireoftheASWC-1.Isolateand tapetheBrown/Whitewire,itwillnotbeused. C. For Kenwood, or select JVC’s with a Blue/Yellow steering wheel control wire:ConnecttheKenwood/JVCsteeringwheel controlwiretotheBrownwireoftheASWC-1.Isolateandtape theBrown/Whitewire,itwillnotbeused. Note: Some of the newer Kenwood radios will auto detect as a JVC. If this is the case, (a) use the included 12k ohm resistor in-line between the Blue/Yellow and Brown wire of the female 3.5mm jack only during programming (remove resistor once programmed) or (b) you can manually set the radio type, refer to the Changing Radio Type section (pp. 12-13). D. For XITE radios:ConnectthesteeringwheelcontrolSWC-2wire fromtheradiototheBrownwireoftheASWC-1.Isolateandtape theBrown/Whitewire,itwillnotbeused. 2) For Parrot Asteroid Smart or Tablets:Connectthe3.5mmjackof theASWC-1intothefemale3.5mmjackoftheAX-SWC-PARROT (soldseparately).Thenplugthe4-pinmaleharnessintothe correspondingsteeringwheelcontrolfemaleharnessintheradio. Note: AX-SWC-PARROT is required (sold separately) and the radio must be updated to rev. 2.1.4 or higher. Additionally, the ASWC-1 must be updated to the most recent software available. 3) For all other radios:Pluginthemale3.5mmconnectorofthe ASWC-1intothebackoftheaftermarketradio,designatedfor anexternalsteeringwheelcontrolinterface.Pleaserefertothe aftermarketradiosmanualifindoubtwherethe3.5mmconnector oftheASWC-1goesinto. 7 ASWC-1 Installation Programming TheASWC-1canbeprogrammedtwodifferentways.Itcanauto programitselfthroughAutoDetectMode,oritcanbemanually programmed(pp.19-21).Thefollowing,whichisrecommended,isfor autoprogramming. Auto Detect Mode: Overview TheASWC-1hastheabilitytoautodetectselectvehiclesandwhat aftermarketradioitisconnectedto.The“ASWC-1VehicleInstructions”, foundatwww.axxessinterfaces.com,willindicateifyourvehiclewillauto detectandwhataction,ifany,isrequiredforthisprocesstotakeplace. Fortheautodetectfeaturetoworkthereare(3)possibleactionsthatmust betaken.Note,onlyoneactionwillberequireddependingonthevehicle: 1. Turntheignitiononandnootheractionisrequired. --- Or --2. Turntheignitionon,pressandholdtheVolume Upbuttononthe steeringwheel. --- Or --3. Turntheignitionon,andthentaptheVolume Upbuttonrepeatedly onthesteeringwheel. Auto Detect Mode: Steps Note: Please read all Auto Detect Mode steps before beginning. 1) Completeconnectionstothevehicleandtheaftermarketradio. 2) Turntheignitionon,theLEDwillstartrapidlyflashingRed;which meanstheASWC-1islookingforthevehicleandtheradio. Note: If the LED did not start flashing Red rapidly press the reset button for 3 seconds and then proceed to Step 3. 3) Performactionrequiredforyourparticularvehicle,asnotedinthe “ASWC-1VehicleInstructions”,downloadfromAxxessinterfaces.com. 8 ASWC-1 Installation Programming 4) AfterafewsecondstheLEDshouldstopflashingrapidlyandgoout forapproximately2seconds.Atthispointdonotpressanybuttons. 5) Aftertheapproximate2secondstherewillbeaseriesof7Green flashes,someshort, andsomelong.Thelongflashesrepresentthe wiresthatarerecognizedbytheASWC-1. Tip: Knowing this will help if you need to troubleshoot; refer to p. 22, for the appropriate LED Feedback section legend. 6) TheLEDwillpauseforanother2seconds,andthenflashRedupto 15timesdependingonwhatradioisconnectedtotheASWC-1. Tip: Knowing this will help if you need to troubleshoot; refer to p. 23, for the appropriate LED Feedback section legend. 7) Thisistheendoftheautodetectionstage.IftheASWC-1detected thevehicleandtheradiosuccessfullytheLEDwilllightupsolid. 8) ForvehicleswithOEBluetoothbuttons,pressandholdthe Hang uporPick upbuttononthesteeringwheelaftertheLEDon theASWC-1goessolid.IftheOEBluetoothbuttonsareabletobe usedtheLEDwillgooutafter3seconds.YourOEBluetoothbuttons arenowprogrammedtoyouraftermarketradio. Note: The aftermarket radio must have Bluetooth capability and must be able to accept these commands. 9) Makesurethesteeringwheelcontrolbuttonsfunctioncorrectlyinthe vehicleandenjoy. Tip: If the ASWC-1 did not go to a solid LED, press the Reset button for 3 seconds, release, and then start from Step 3. If the LED still doesn’t go to a solid LED refer to the LED Feedback section (p. 22).This will help you to determine if the ASWC-1 is detecting your vehicle. If not, refer to the instructions starting on p. 6, and make sure all the instructions were followed as stated. If you have done this and the ASWC-1 is still not going to a solid LED please refer to the Troubleshooting section (pp. 16-18). 9 ASWC-1 Installation Remapping the SWC buttons Let’ssayyouhaveASWC-1programmedtoyourradioandyouwant tochangethebuttonassignmentforthesteeringwheelcontrols.For instance,youwouldlikeSeek UptobeMute.Followthestepsbelowto remapthesteeringwheelcontrolbuttons: 1) MakesuretheASWC-1isvisible,soyoucanseetheLEDflashesto confirmbuttonrecognition. Tip: Turning off the radio is recommended. 2) Withinthefirst20secondsofturningtheignitionon, pressandholdtheVolume Upbuttononthesteeringwheeluntilthe LEDgoessolid. 3) ReleasetheVolume UpbuttonandtheLEDwillgoout;Volume Up hasnowbeenprogrammed. 4) FollowthelistintheButtonAssignmentLegend(p.11), toreferencetheorderinwhichthesteeringwheelcontrolbuttons needtobeprogrammed. Note: If the next function on the list is not on the steering wheel; press the Volume Up button for 1 second, until the LED comes on, and then release the button. This will tell the ASWC-1 that the function is not available and it will move onto the next function. 5) Tocompletetheremappingprocess,pressandholdtheVolume Up buttononthesteeringwheeluntiltheLEDontheASWC-1goesout. 10 ASWC-1 Installation Remapping the SWC buttons Button Assignment Legend 1.VolumeUp 8.PresetDown 2.VolumeDown 9.Power 3.SeekUp/Next 10.Band 4.SeekDown/Prev 11.Play/Enter 5.Source/Mode 12.PTT(PushtoTalk)* 6.Mute 13.OnHook 7.PresetUp 14.OffHook *Only the following Pioneer models have the capability of retaining this feature: AVIC-Z110BT, AVIC-Z120BT, AVIC-Z130BT, AVIC-Z140BT, AVIC-X920BT, AVIC-X930BT, AVIC-X940BT. Note: Not all radios will have all of these commands. Please refer to the radio owner’s manual or contact the radio vendor directly for specific commands recognized by that particular radio. 11 ASWC-1 Installation Changing Radio Type 1) After3secondsofturningthekeyon,pressandholdtheVolume DownbuttononthesteeringwheeluntiltheLEDontheASWC-1 goessolid. 2) ReleasetheVolume Downbutton;theLEDwillgooffindicatingwe arenowinChangingRadioTypemode. 3) RefertotheRadioLegend(p.13)toknowwhichradionumberyou wouldliketohaveprogrammed. 4) PressandholdtheVolume UpbuttonuntiltheLEDgoessolid,then release.Repeatthisstepforthedesiredradionumberyouhave selected. 5) Oncethedesiredradionumberhasbeenselected,pressandhold theVolume Downbutton,onthesteeringwheel,untiltheLEDgoes solid.TheLEDwillremainonforabout3secondswhileitstoresthe newradioinformation. 6) OncetheLEDgoesofftheChangingRadioTypemodewillend.You cannowtestthesteeringcontrolwheelcontrols. Note: If at any time the user fails to press any button for a period longer then 10 seconds this process will abort. 12 ASWC-1 Installation Changing Radio Type Radio Legend 1.Eclipse(Type1) 9. Valor 2.Kenwood 10.Clarion(Type2) 3.Clarion(Type1) 11.MetraOE 4.SonyandDual 12.Eclipse(Type2) 5.JVC 13.LG 6.PioneerandJensen 14.Parrot* 7.Alpine 15.XITE 8.Visteon * AX-SWC-PARROT is required (sold separately) and the radio must be updated to rev. 2.1.4 or higher. Additionally, the ASWC-1 must be updated to the most recent firmware available. Note: If you have a Clarion radio and the ASWC-1 did not work try the other Clarion radio type, same for the Eclipse. 13 ASWC-1 Installation Dual Assignment Instructions Note: Seek Up and Seek Down are already set to Preset Up and Preset Down for a long button press. 1) Turnontheignitionbutdonotstartthevehicle. 2) Pressandholddownthesteeringwheelbutton,thatyouwantto assignalongpressfunction,forabout10secondsuntiltheLED rapidlyflashesgreen.AtthispointreleasethebuttonandtheLED willgosolidgreen. 3) Pressandreleasethe Volume Upbuttonthenumberoftimes correspondingtothenewbuttonnumberselected(refertothechart onp.15).ThegreenLEDwillblinkrapidlywhentheVolume Upis pressedandbacktosolidgreenwhenreleased.Thengotothenext stepwhentheVolume Upbuttonhasbeenpressedthedesired numberoftimes. Caution: If more than 10 seconds elapses between a Volume Up button press this procedure will abort, and the LED will go off. 4) Tostorethelongpressbuttoninmemory,pressthebuttonthatyou assignedalongpressbutton(thebuttonhelddowninStep1).The LEDwillnowgooffindicatingithasbeenstored. Note: These steps must be repeated for each button you would like to assign dual purpose action to. Toresetabutton,backtoitsoriginaluse,repeatStep1.Thenpressthe Volume Downbutton.TheLEDwillgooffandthelongpressmapping for thebuttonwillbeerased. 14 ASWC-1 Installation Dual Assignment Instructions Dual Assignment Legend Button Number New Button Action 1 Notallowed 2 Notallowed 3 SeekUp/Next 4 SeekDown/Prev 5 Mode/Source 6 Mute 7 PresetUp 8 PresetDown 9 Power 10 Band 11 Play/Enter 12 PTT 13 OnHook 14 OffHook 15 FanUp 16 FanDown 17 TempUp 18 TempDown 15 ASWC-1 Troubleshooting Auto Detect Mode IftheautodetectfeaturewastriedandattheendtheLEDdid notgosolid,butinsteadcontinuallyflashes;thismeansthattheASWC-1 didnotdetectthevehicle.Followthesestepstodeterminewhatmay havehappened: 1) Verifythatyouhavea12-voltDContheRedaccessorywireofthe ASWC-1,usingamultimeter. 2) ReconfirmthatyouhaveagoodgroundtothesolidBlackwireof theASWC-1. Attention: Due to the nature of how microprocessors function, sometimes having the ASWC-1’s ground shared and using the factory ground in the OE wiring harness is not sufficient; and will cause problems. The use of a chassis ground solely by itself is highly recommended, especially in data communication vehicles. Attach the solid Black wire of the ASWC-1 to a good chassis ground, all by itself. Ensure this wire is straight from the ASWC-1 without any extensions, and make sure a ring terminal (not supplied) is used, and crimped properly. This will alleviate any grounding issues that may keep the ASWC-1 from programming; most cases of the ASWC-1 not programming comes from the lack of this step being done. 3) RecheckthatthewiresconnectedtotheASWC-1andvehicleare correct;referencingthe“ASWC-1VehicleInstructions”document, foundontheaxxessinterfaces.comwebsite. 4) VerifythatthewiresconnectedfromtheASWC-1tothevehicle areconnecteddirect;i.e.,solder,crimpcap,militarysplice.No tappingstyleconnectors,orbuttconnectorsarepermitteddueto increasedresistance. 16 ASWC-1 Troubleshooting Auto Detect Mode Note: If a pre-wired harness is being used and you have tried all the troubleshooting steps listed above, if the ASWC-1 still does not go to a solid LED, remove the pre-wired ASWC-1 harness and use the harness that came with the ASWC-1. Ifyouhaveperformedanyofthestepsabove;reprogramtheASWC-1 bypressingtheresetbuttonontheASWC-1for3seconds,release,and thenfollowtheinstructionsonp.9, startingfromStep3.IftheASWC-1 stilldoesnotgotoasolidLEDattheend,pleaserefertoManual ProgrammingModeonpp.19-21tomanuallyprogramtheASWC-1. IftheASWCdidgotoasolidLEDbutstilldoesnotwork,followthese stepstotroubleshoottheradioprogrammingportionoftheauto programmingsequence: 1) Confirmthatthe3.5mmjackonASWC-1isconnectedtoyour radiosecurely,andinthecorrectjackoftheradio.Makesureitis notpluggedintotheBluetoothmicorAUXjack.Ifyouarenotsure whatjacktoconnecttotheradio,pleasecontacttheradiovendor. Ifthewrongjackoftheradiowasconnectedto,correctit;andthen reprogramtheASWC-1. Note: Some radios do not use a jack for the steering wheel controls, instead they use a wire. If so, reference Connections to be Made (p. 6), and ensure that you have the proper wire(s) connected. 2) Ifyouareusingaradiowithawireforconnectionsinsteadofajack, makesureyouhavealsoprogrammedthesteeringwheelcontrolsto theradiofollowingtheinstructionsincludedwiththeradio.Contact theradiovendorifyouhaveanyquestionswiththis. Note: This does not apply to JVC and Kenwood radios. 17 ASWC-1 Troubleshooting Auto Detect Mode 3) For Kenwood radios,makesurethattheASWC-1displaysthata Kenwoodradioisbeingused;referencetoRadioLegend(p.21).If theRadioLegendshowsaJVCradioinstead,thenreferencetothe ChangingRadioType(p.12)toforceprogramtheASWC-1to displayKenwood. Tip: Some Kenwood radios have a feature called Remote Sensor. If your radio has this feature, ensure it is turned on. If it is on, turn it off, then back on. 4) For Alpine radios,removethe3.5mmjackfromtheradio, reprogramtheASWC-1withthejackremoved,andthenreconnect the3.5mmjackbackintotheradio. Tip: Some Alpine radios have a feature that turns the remote to either the back, or the front. If you have one of these radios, ensure the sensor is on the rear setting. If the setting is on the rear, turn it to the front, then back to the rear. 5) For Pioneer and Sony radios,iftheASWC-1works,butthebuttons areoutoforder,orbecomeoutoforder;thiscouldbecausedbythe 3.5mmjackontheASWC-1notseatingproperly,slippingout,ordirt onthecontacts.Additionally,sometimesthiscanbeintermittent. Removeanydirtonthecontacts,reinsertthejackfirmlyintothe radio,andthenputastresslooponthe3.5mmcabletopreventthis fromhappeninginthefuture.Also,ifanythingisprohibitingthejack fromseatingallthewayin,suchasaheatsink,lightlytrimsomeof theplasticfromthe3.5mmjackasneeded. 18 ASWC-1 Troubleshooting Manual Programming Mode IfyourvehicleisnotlistedforautodetectionbytheASWC-1on theAxxesswebsite,www.axxessinterfaces.com,youmaybeableto manuallyprogramanon-datacommunicationvehicleusingthe followingsteps. Tip: If you do not know if you have a data communication vehicle or not, refer to the “ASWC-1 Vehicle Instruction” document, from www.axxessinterfaces.com. If it indicates to press and release the Volume Up button repeatedly to program the ASWC-1, then you have a data communication vehicle. Note: Not every radio will have all the possible steering wheel control commands on the steering wheel. Aftermarket radios that do not have Bluetooth will not recognize the PTT (Push to Talk) or On/Off Hook commands, however these buttons may be able to be manually programmed to do other commands. Please refer to the radio owner’s manual or radio vendor for specific commands that the radio will recognize. Note: Please read all Manual Programming Steps before beginning. 1) FollowthestepsintheConnectionstobeMadesection(p.6-7)to wireuptheASWC-1toyourradio. 2) Turntheignitionon,thenpressandholdtheResetbuttononthe ASWC-1forapproximately10secondsuntiltheLEDontheASWC-1 flashesslow;andthenreleasetheResetbutton. 3) Atthispoint,pressandholdtheVolume Upbuttononthesteering wheelfor7secondsuntiltheLEDgoessolid.Nowreleasethe Volume Upbutton,andtheLEDwillgooff. Volume Uphasnow beenprogrammed. 19 ASWC-1 Troubleshooting Manual Programming Mode 4) Next,pressandholdtheVolume Downbuttonuntilthe LEDgoessolid.ReleasetheVolume Down buttonandtheLED willturnoff;Volume Downhasnowbeenprogrammed. 5) AtthispointrefertheManualProgrammingLegend(p.21)and continuetotheSeek Up/Nextbutton. Note: For any command that needs to be skipped, press the Volume Up button for each one. The LED should light up each time you press the Volume Up button. 6) Afterthelastbuttononyoursteeringwheelhasbeenprogrammed, pressandholdtheVolume UpbuttonuntiltheLEDflashesslow;and thenreleasetheVolume Upbutton. Note: If at any time an error is made hold down the reset button on the ASWC-1 for 10 or more seconds. This will restart the manual programming. Go back to Step 4 and start again. 7) PressandholdtheVolume DownbuttonuntiltheLEDstartsto flashquickly. 8) ReleasetheVolume Downbutton. 9) Afterapproximately4secondsoftheLEDflashingquicklytheLED willgooutfor2seconds. 10) ThentheLEDwillflash,upto15times,dependingonwhatradio isconnectedtotheASWC-1. 11) Makesurethenumberofflashesmatchwhatradioyouhave installed.RefertotheRadioLegend(p.13). Note: If the number of flashes do not match the radio you have installed, refer to the Changing Radio Type section (p. 13). 20 ASWC-1 Troubleshooting Manual Programming Mode 12) PressandholddowntheVolume DownbuttonuntiltheLED goessolid. 13) Programmingforthevehicleandtheradioisnowcomplete. Next,testthesteeringwheelcontrolfunctionstomakesureit workscorrectly. Manual Programming Legend 1.VolumeUp 10.Band 2.VolumeDown 11.Play/Enter 3.SeekUp/Next 12.PTT(PushtoTalk) 4.SeekDown/Prev 13.OnHook 5.Source/Mode 14.OffHook 6.Mute 15.FanUp 7.PresetUp 16.FanDown 8.PresetDown 17.TempUp 9.Power 18.TempDown 21 ASWC-1 Troubleshooting Resetting Original ASWC-1 Settings 1) Turntheignitiononandwait3seconds. 2) PresstheResetbuttonfor3secondsandthenrelease. 3) RefertotheProgrammingsection(pp.8-9)toprogramtheASWC-1. 4) OncetheLEDissolidtheASWC-1isresetandshouldbeoperating withthedefaultsettings. ASWC-1 Troubleshooting LED Feedback A. Vehicle LED Feedback (indicatedbyGreenLEDontheASWC-1) 1st LEDflashistheWhite/Green 2nd LEDflashistheYellow/Green 3rd LEDflashistheGreen/Orange 4th LEDflashistheGray/Red 5th LEDflashistheBlack/Green 6th LEDflashistheGray/Blue 7th LEDflashisthePink Note (section A): • Short flashes represent the steering wheel control wire(s) that are not connected to the vehicle from the ASWC-1. • Long flashes represent wire(s) that are connected to the vehicle. 22 ASWC-1 Troubleshooting LED Feedback B. Radio LED Feedback (indicatedbyRedLEDontheASWC-1) 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 12th 13th 14th 15th LEDflashisforEclipse(Type1) LEDflashisforKenwood LEDflashisforClarion(Type1) LEDflashisforSonyandDual LEDflashisforJVC LEDflashisforPioneerandJensen LEDflashisforAlpine* LEDflashisforVisteon LEDflashisforValor LEDflashisforClarion(Type2) LEDflashisforMetraOE LEDflashisforEclipse(Type2) LEDflashisforLG LEDflashisforParrot** LEDflashisforXITE *Note (section B): If the ASWC-1 flashes 7 times and you do not have an Alpine radio connected to it that means that the ASWC-1 did not see any radio connected. Verify the 3.5mm connector is connected to the steering wheel control input into the radio. **Note (section B): The AX-SWC-PARROT is required (sold separately). The radio must be updated to rev. 2.1.4 or higher from www.parrot.com and ASWC-1 must be updated to the latest firmware from www.axxessinterfaces.com. 23 INSTALLATION INSTRUCTIONS ASWC-1 IMPORTANT WARNING Thisproductincludesinstructionsforinstallationwhichmustbecarefully followed.Theinstructionsarewordedinsuchamannertoassume thattheinstalleriscapableofcompletingthesetypeofelectronic installations.Ifyouareunclearastowhatyouareinstructedtodoor believethatyoudonotunderstandtheinstructionssoastoproperlyand safelycompletetheinstallationyou should consult a technician who does have this knowledge and understanding. Failure to follow these instructions carefully and to install the interface as described could cause harm to the vehicle or to safety systems on the vehicle. Interference with certain safety systems could cause harm to persons as well. If you have any questions in this regard please call the Help line or Metra at 1-800-221-0932 for assistance. REV. 3/27/2014 ASWC-INST10 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians US.PAT.NOS.8014920and8214105 1-800-221-0932 AxxESSINTERfACES.COM © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION INSTRUCCIONES DE INSTALACIÓN ASWC-1 ASWC-1 Manual de instalación de la interfase de control en volante Axxess US.PAT.NOS.8014920y8214105 CaraCterístiCas Componentes de la interfase InterfaseASWC-1•Arnésde12pinsconconectormacho de3.5mm•Conectorhembrade3.5mmconcables marrón/blanco•Resistenciade12kohmios Herramientas requeridas •Cortador•Pelacables•Cinta METRA. THE WORLD’S BEST KITS.™ 1-800-221-0932 metraonline.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION REV. 4/15/2014 ASWC-INST10 • Unainterfasehacetodo-Noserequiereninterfasesadicionales • Diseñadoparasercompatiblecontodaslasmarcas principalesderadios • Detectaautomáticamenteeltipodevehículo,laconexiónde radioypreconfiguraloscontroles • Sepuedenasignarbotonesdualesdecontrolenelvolante • Sepuedeprogramarmanualmenteenlamayoríadelosvehículos • Lamemoriaretienelaconfiguracióninclusodespuésdequese desconectelabateríaoseeliminelainterfase • Todaslasconexionessehacenenellugardelradio • Actualizablepormicro“B”USB Índice Prefacio ............................................................................................. 3 Información general – IntroductiontotheASWC-1InterfaceandWiringHarness ..............4-5 Instalación del ASWC-1 – Conexionesquesedebenhacer ....................................................6-7 – Programación ................................................................................8-9 Mododedetecciónautomática:Informacióngeneral ................... 8 Mododedetecciónautomática:Steps ......................................8-9 –RemapeodelosbotonesSWC ...................................................10-11 Leyendadeasignacióndebotones ............................................ 11 –Cambiodetipoderadio .............................................................12-13 Leyendaderadio ....................................................................... 13 –Instruccionesdeasignacióndual ...............................................14-15 Leyendadeasignacióndual ...................................................... 15 Resolución de problemas de ASWC-1 – Mododedetecciónautomática ..................................................16-18 – Mododeprogramaciónmanual .................................................19-21 ManualProgramaciónLegend ................................................... 21 – RestablecimientodelosajustesoriginalesdeASWC-1.................... 22 –RetroalimentaciónLED ..............................................................22-23 PRECAUCIÓN: Metra recomienda desconectar el terminal negativo de la batería antes de comenzar cualquier instalación. Todos los accesorios, interruptores y, especialmente, las luces indicadoras de airbag deben estar enchufados antes de volver a conectar la batería o comenzar el ciclo de ignición. Nota: Remítase a las instrucciones incluidas con el radio de postventa. 2 Prefacio Lo que debe saber antes de empezar 1) Conozcaelaño,marcaymodelocorrectosdesuvehículo. 2) Asegúresedequeloscontrolesenelvolantefuncionenantesderetirar elradiodefábricaysepacuáleselbotóndeaumentar volumen.El botóndeaumentar volumenseusaparalaprogramación,asíquees importantesaberestoantesderetirarelradio. Nota: Los controles en el volante deben ser los que vienen con el vehículo cuando este se compró. No aceptamos trabajos personalizados, es decir, agregar un nuevo volante con botones agregados/nuevos. 3) VisiteelsitiowebdeAxxess(axxessinterface.com)yhagaclicen elenlacetitulado“ASWC-1VehicleInstructions”(Instruccionesdel vehículoconASWC-1),ubicadoenlapartederechadelapantalla enelcentro.Unavezqueingreselainformacióndesuvehículo, hagaclicenelbotón“Submit”(Enviar).Estolollevaráaotra página,dondeharáclicenelenlacebajolapalabra“Documents” (Documentos).Estoleproporcionarálasinstruccionesespecíficas alvehículoparasuvehículo.Imprimaestedocumentoparaquelo tengaensuvehículodurantelainstalación,yaqueestaeslamejor fuentedeinformación,ademásdeserlamásreciente. 4) Asegúresedequeelradioqueestáinstalandoseacompatiblecon elASWC-1.Además,consultelaleyendadelradio(pág.13)yel manualdelpropietariodesuradio. 5) ActualiceelASWC-1conelsoftwaremásreciente.Nota: Para actualizarlo vaya a axxessinterfaces.com y descargue el programa WebXXpress. Atención: Auque hemos realizado una amplia investigación y pruebas para verificar que los cables del control en el volante que enumeramos son correctos. Es su responsabilidad verificar que los cables del control en el volante que enumeramos sean correctos con un multímetro. Si encuentra algún error, por favor notifique a nuestro Departamento Técnico de Axxess al 1-800-253-TECH. Por favor llame desde su vehículo, mientras está estacionado, y tenga acceso a la interfase y al cableado del vehículo cuando realice la llamada. 3 Información general Introducción a la interfase ASWC-1 y al arnés de cables EnlapartesuperiordelainterfaseASWC-1haytrespuntosdeinterés: 1) LED de programación 2) Botón de restablecimiento 3) Cubierta del puerto de actualización(desliceparaabrirla) Micro “B” USB Cubiertadelpuerto Botónde deactualización restablecimiento* *Nota: El botón de restablecimiento está empotrado. Se necesita un objeto como un sujetapapeles parcialmente desdoblado para oprimir el botón. 4 LEDde programación Información general AcontinuaciónseindicanloscoloresdeloscablesdelASWC-1. VisiteelsitiowebdeAxxessenwww.axxessinterfaces.compara obtenerinformacióndetalladasobresuvehículoespecíficoypara sabercuálescoloresdecablesusarconlainterfaseASWC-1. Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Rosa Blanco/Verde Amarillo/Verde Verde/Anaranjado Gris/Rojo Negro Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Azul/Rosa Negro/Verde Rojo (punta del conector de 3.5mm) Blanco (aro de conector de 3.5mm) Gris/Azul Rojo Se muestra abajo: Conector hembra de 3.5mm con cables marrón (Br) y marrón/blanco (Br/W) Br Se muestra arriba: Arnés de 12 pins con conector macho de 3.5mm Br/W 5 Instalación del ASWC-1 Conexiones que se deben hacer Unavezquehayarecolectadooimpresolas“Instruccionesdel vehículoconASWC-1”sobresuvehículoespecíficoenelsitio www.axxessinterface.com,estálistoparainstalarelASWC-1. Nota: Si el cableado para su vehículo no está disponible en nuestro sitio web, necesitará buscarlo por su cuenta. Confirme primero con el departamento de soporte técnico de Axxess al 1-800-253-TECH, puesto que nosotros podemos tener esta información. Dentro del vehículo: 1) ConecteelcablenegrodelASWC-1atierra.Puedeusarelmismo puntoatierraqueelradiodemercadosecundario,peroesmuy recomendableconectarelASWC-1atierraconelchasísdel vehículo,sincompartirlaconexión. 2) Conlallaveenlaposicióndeapagado,conecteelcablerojodel ASWC-1conelcabledeaccesoriosde12voltios. 3) Localiceloscablescorrectosdelcontrolenelvolanteenelarnésdel vehículo,segúnsedescribaenlas“Instruccionesdelvehículocon ASWC-1”.ConecteestoscablesconelASWC-1. Nota: Metra recomienda que los cables se suelden para lograr la mejor conexión, y la más segura. No se recomienda usar conectores de tipo rosca debido a que tienen una mayor probabilidad de crear una conexión intermitente o un cambio en los valores de resistencia (provocará que el ASWC-1 no se pueda programar). Dentro del radio: 1) Paralosradiosenumeradosacontinuación,conecteeladaptador hembrade3.5mm(conloscablesmarrónymarrón/blanco)al conectormachode3.5mmdelarnésdelASWC-1. A. Para radios Eclipse:Conecteloscablesdelcontrolenelvolante Eclipse(normalmentemarrónymarrón/negro)conloscables marrónymarrón/blancodelASWC-1.ElmarróndelASWC-1 seconectaalmarrón/negrodelEclipseyelmarrón/blancodel ASWC-1seconectaconelmarróndelEclipse. 6 Instalación del ASWC-1 Conexiones que se deben hacer B. Para radios Metra OE: ConecteelcableClave1(gris)delcontrol enelvolanteconelcablemarróndelASWC-1.Aísleyencinteel cablemarrón/blanco,noseutilizará. C. Para Kenwood o algunos JVC con cable del control en el volante azul/amarillo: Conecteelcabledelcontrolenelvolante Kenwood/JVCconelcablemarróndelASWC-1.Aísleyencinteel cablemarrón/blanco,noseutilizará. Nota: Algunos de los radios Kenwood más nuevos se detectarán automáticamente como JVC. Si este es el caso, (a) use la resistencia de 12 k ohmios incluida en línea entre el cable azul/ amarillo y marrón del conector hembra de 3.5 mm únicamente durante la programación (retire la resistencia después programar) o (b) puede ajustar manualmente el tipo de radio, consulte la sección Cambiar el tipo de radio (págs. 12 y 13). D. Para radios XITE: ConecteelcableSWC-2delcontrolenel volantedelradioalcablemarróndelASWC-1.Aísleyencinteel cablemarrón/blanco,noseutilizará. 2) Para Parrot Asteroid Smart o tabletas:Conecteelconectorde3.5 mmdelASWC-1conelconectorhembrade3.5mmdelAX-SWCPARROT(sevendeporseparado).Luegoconecteelarnésmachode 4pinsconelcorrespondientearnéshembradelcontrolenelvolante delradio. Nota: Se requiere AX-SWC-PARROT (se vende por separado) y el radio debe actualizarse a la versión 2.1.4 o más reciente. Además, el ASWC-1 debe actualizarse al software más reciente disponible. 3) Para todos los demás radios:Conecteelconectormachode 3.5mmdelASWC-1enlaparteposteriordelradiodemercado secundario,designadaparaunainterfasedecontrolenvolante externo.Consulteelmanualdelosradiosdemercadosecundario sitienedudasacercadedóndedebeirelconectorde3.5mm delASWC-1. 7 Instalación del ASWC-1 Programación ElASWC-1puedeprogramarsededosmanerasdiferentes.Puede programarseautomáticamenteporsísolomedianteelmodode detecciónautomáticaopuedeprogramarsemanualmente(págs.19a 21).Serecomiendalosiguienteparalaprogramaciónautomática. Modo de detección automática: Información general ElASWC-1tienelacapacidaddedetectarautomáticamentealgunos vehículosyacuálradiodemercadosecundarioestáconectado.El documento“InstruccionesdelvehículoconASWC-1”,queseencuentra enelsitiowww.axxessinterface.com,indicarásisuvehículoserá detectadoautomáticamenteyquéacción,dehaberla,debeseguirusted paraqueesteprocesoselleveacabo. Paraquelafuncióndedetecciónautomáticafuncionehay(3)acciones posiblesquedebenllevarseacabo.Tengaencuentaquesolose necesitaráunaaccióndependiendodelvehículo: 1. Enciendalaigniciónynoserequiereningunaotraacción. --- O bien --2. Enciendalaignición,presioneymantengapresionadoelbotónde aumentar volumenenelvolante. --- O bien --3. Enciendalaigniciónyluegooprimaelbotóndeaumentar volumenenelvolante. Modo de detección automática: Pasos Nota: Lea todos los pasos del modo de detección automática antes de comenzar. 1) Realicelasconexionesalvehículoyalradiodemercadosecundario. 2) Enciendalaignición;elfocoLEDempezaráaparpadearrápidamente decolorrojo,loquesignificaqueelASWC-1estábuscandoel vehículoyelradio. Nota: Si el foco LED no empezó a parpadear rápidamente de color rojo, presione el botón de restablecimiento por 3 segundos y continúe con el paso 3. 3) Realicelaacciónrequeridaparasuvehículoespecíficocomose indicaeneldocumento“InstruccionesdelvehículoconASWC-1”, quesedescargóenAxxessinterfaces.com. 4) Despuésdevariossegundos,elfocoLEDdebedejardeparpadear 8 Instalación del ASWC-1 Programación ynoiluminarseduranteaproximadamente2segundos.Eneste momento,nopresioneningúnbotón. 5) Despuésdeaproximadamente2segundos,habráunaseriede7 parpadeosdecolorverde,algunoscortosyalgunoslargos.Los parpadeoslargosrepresentanloscablesquesonreconocidosporel ASWC-1. Sugerencia:Saberestoleayudaráencasodenecesitarresolver problemas,consultelapágina22parabuscarlaleyendacorrectaen lasecciónderetroalimentaciónLED. 6) ElfocoLEDpausaráduranteotros2segundosyluegoparpadearáde colorrojohasta15vecesdependiendodelradioqueseconectóal ASWC-1. Sugerencia:Saberestoleayudaráencasodenecesitarresolver problemas,consultelapágina23parabuscarlaleyendacorrectaen lasecciónderetroalimentaciónLED. 7) Esteeselfinaldelaetapadedetecciónautomática.SielASWC1detectóelvehículoyelradiodeformaexitosa,elfocoLEDse iluminarásinparpadear. 8) ParavehículosconbotonesBluetoothdelfabricanteoriginal, presioneColgaroDescolgarenelcontroldesuvolantedespués dequeelfocoLEDdelASWC-1seenciendasinparpadearSipueden utilizarselosbotonesdeBluetoothdelfabricantedeequipooriginal, elfocoLEDseapagarádespuésde3segundos.Losbotonesdesu Bluetoothoriginalahoraestánprogramadosensuradiode mercadosecundario. Nota: El radio de mercado secundario debe ser compatible con Bluetooth y debe ser capaz de aceptar estos comandos. 9) Asegúresedequelosbotonesdecontrolenelvolantefuncionen correctamenteenelvehículoydisfrute. Sugerencia: Si el foco LED del ASWC-1 no se enciende sin parpadear, presione el botón de restablecimiento por 3 segundos, suéltelo y empiece a partir del paso 3. Si el foco LED aún no se enciende sin parpadear consulte la sección de retroalimentación LED (pág. 22). Esto le ayudará a determinar si el ASWC-1 está detectando su vehículo. De lo contrario, consulte las instrucciones empezando en la pág. 6 y asegúrese de seguir todas las instrucciones como se indican. Si ha hecho esto y el ASWC-1 aún no se enciende sin parpadear, consulte la sección de resolución de problemas (págs. 16 a 18). 9 Instalación del ASWC-1 Remapeo de los botones SWC DigamosquetieneelASWC-1programadoparasuradioyahora quierecambiarlaasignacióndelosbotonesparaloscontrolesdel volante.Porejemplo,legustaríaqueelbotóndebuscar siguiente funcionaracomosilencio.Sigaestospasospararemapearlosbotones decontrolenelvolante: 1) AsegúresedetenerelASWC-1visible,paraquesepueda verelparpadeodelfocoLEDparaconfirmarelreconocimientode losbotones. Sugerencia: Se recomienda apagar el radio. 2) Dentrodelosprimeros20segundosdespuésdeencenderla ignición,presioneymantengapresionadoelbotóndeaumentar volumendelvolantehastaqueelLEDdejedeparpadear. 3) Suelteelbotóndeaumentar volumenyelfocoLEDseapagará, ahoraelbotóndeaumentar volumensehaprogramado. 4) Sigalalistaenlaleyendadeasignacióndebotones(pág.11), paraconsultarelordenenquelosbotonesdelcontrolenelvolante debenprogramarse. Nota: Si la siguiente función de la lista no está en el volante, presione el botón de aumentar volumen durante 1 segundo hasta que el foco LED se encienda y luego suelte el botón. Esto le indica al ASWC-1 que la función no está disponible y pasará a la siguiente función. 5) Paraterminarelprocesoderemapeo,presioneymantenga presionadoelbotóndeaumentar volumenenelvolantehastaque seapagueelfocoLEDenelASWC-1. 10 Instalación del ASWC-1 Remapeo de los botones SWC Leyenda de asignación de botones 1.Subirvolumen 8.Bajarprestablecido 2.Bajarvolumen 9.Encendido 3.Buscarsiguiente 10.Banda 4.Buscaranterior 11.Reproducir/Aceptar 5.Fuente/Modo 12.PTT(presionarparahablar) 6.Silencio 13.Colgado 7.Subirprestablecido 14.Descolgado *Solo los siguientes modelos Pioneer son capaces de retener esta función: AVIC-Z110BT, AVIC-Z120BT, AVIC-Z130BT, AVIC-Z140BT, AVIC-X920BT, AVIC-X930BT, AVIC-X940BT. Nota: No todos los radios tienen todos estos comandos. Consulte el manual del propietario del radio o comuníquese con el proveedor del radio directamente para obtener los comandos específicos reconocidos por ese radio en particular. 11 Instalación del ASWC-1 Cambio de tipo de radio 1) Despuésde3segundosdegirarlallaveaencendido,presioney mantengapresionadoelbotóndebajar volumenenelvolante hastaqueelfocoLEDenelASWC-1seenciendasinparpadear. 2) Suelteelbotóndebajar volumen,elfocoLEDseapagaráindicando queahoraestamosenelmododecambiodetipoderadio. 3) Consultelaleyendaderadio(pág.13)parasaberquénúmerode radiolegustaríaprogramar. 4) Presioneymantengapresionadoelbotóndeaumentar volumenhastaqueelfocoLEDseenciendasinparpadear,luego suéltelo.Repitaestepasoparaelnúmeroderadiodeseadoque haseleccionado. 5) Despuésdeseleccionarelnúmeroderadiodeseado,presioney mantengapresionadoelbotóndebajar volumenenelvolante hastaqueelfocoLEDseenciendasinparpadear.ElfocoLED permaneceráencendidoduranteaproximadamente3segundos mientrasalmacenalainformacióndelnuevoradio. 6) DespuésdeapagarseelfocoLED,finalizaráelmododecambiode tipoderadio.Ahorapuedeprobarloscontrolesenelvolante. Nota: Si en cualquier momento el usuario no presiona ningún botón por un periodo mayor a 10 segundos, este modo de programación se abortará. 12 Instalación del ASWC-1 Cambio de tipo de radio Leyenda de radio 1.Eclipse(Tipo1) 9. Valor 2.Kenwood 10.Clarion(Tipo2) 3.Clarion(Tipo1) 11.MetraOE 4.SonyandDual 12.Eclipse(Tipo2) 5.JVC 13.LG 6.PioneerandJensen 14.Parrot* 7.Alpine 15.XITE 8.Visteon *Se requiere AX-SWC-PARROT (se vende por separado) y el radio debe actualizarse a la versión 2.1.4 o más reciente. Además, el ASWC-1 debe actualizarse al firmware más reciente disponible. Nota: Si tiene un radio Clarion y el ASWC-1 no funcionó pruebe con el otro tipo de radio Clarion, lo mismo aplica con el radio Eclipse. 13 Instalación del ASWC-1 Instrucciones de asignación dual Nota: Los botones buscar siguiente y buscar anterior ya están configurados en subir prestablecido y bajar prestablecido al presionar y sostener el botón. 1) Enciendalaigniciónperonoenciendalamarchadelvehículo. 2) Presioneysostengaelbotóndelvolantealquedeseaasignara unafuncióndepresionarysostener,durantealmenos10segundos hastaqueelfocoLEDparpadeerápidamentedecolorverde.Eneste momentosuelteelbotónyelfocoLEDseencenderásinparpadear. 3) Presioneysuelteelbotóndeaumentar volumenelnúmerode vecesquecorresponda alnúmerodelnuevobotónseleccionado (consultelatablaenlapág.15).ElfocoLEDdecolorverde parpadearárápidamentecuandosepresionaelbotóndeaumentar volumenyseencenderásinparpadeardecolorverdecuandose suelta.Luegovayaalsiguientepasocuandoelbotóndeaumentar volumensehapresionadoelnúmerodevecesdeseado. Precaución: Si transcurren más de 10 segundos entre cada vez que presiona el botón de aumentar volumen, este procedimiento se abortará y se apagará el foco LED. 4) Paraalmacenarenlamemoriaelbotóndepresionarysostener, presioneelbotónalqueasignócomobotóndepresionarysostener (elbotónquesemantuvopresionadoenelpaso1).ElfocoLED ahoraseapagaráindicandoquesehaalmacenado. Nota: Estos pasos deben repetirse con cada botón al que le gustaría asignar una acción de doble propósito. Pararestablecerunbotónasuusooriginal,repitaelpaso1.Luego presioneelbotóndebajar volumen.ElfocoLEDseapagaráyelmapeo depresionarysostenerdeesebotónseborrará. 14 Instalación del ASWC-1 Instrucciones de asignación dual Leyenda de asignación dual Número de botón Nueva acción del botónn 1 Nosepermite 2 Nosepermite 3 Buscarsiguiente 4 Buscaranterior 5 Modo/Fuente 6 Silencio 7 Subirprestablecido 8 Bajarprestablecido 9 Potencia 10 Banda 11 Reproducir/Aceptar 12 PTT 13 Colgado 14 Descolgado 15 Aumentarventilador 16 Disminuirventilador 17 Aumentartemperatura 18 Disminuirtemperatura 15 Resolución de problemas de ASWC-1 Modo de detección automática SilafuncióndedetecciónautomáticaseintentóyalfinalelfocoLED noseencendiósinparpadear,sinoqueparpadeócontinuamente;esto significaqueelASWC-1nodetectóelvehículo.Sigaestospasospara determinarquépuedehaberocurrido: 1) Verifiquequetenga12voltiosdeCDenelcablerojodeaccesorios delASWC-1,usandounmultímetro. 2) VuelvaaconfirmarqueelcablenegrodelASWC-1tieneuna conexiónatierracorrecta. Atención: Debido a la naturaleza del funcionamiento de los microprocesadores, algunas veces compartir la conexión a tierra del ASWC-1 y usar la conexión a tierra de fábrica del arnés de cables original no es suficiente, y ocasionará problemas. Se recomienda ampliamente usar la tierra al chasís sin compartir especialmente en vehículos con comunicación de datos. Sujete el cable negro del ASWC-1 a tierra del chasís sin compartir esta conexión. Asegúrese de que el cable venga directamente del ASWC-1 sin ninguna extensión, y asegúrese de usar una terminal de aro (no suministrada) y que esté correctamente pelada. Esto resolverá cualquier problema de conexión a tierra que pudiera impedir la programación del ASWC-1; en la mayoría de los casos el ASWC-1 no se programa debido a la omisión de este paso. 3) VuelvaarevisarqueloscablesconectadosalASWC-1yel vehículoseanloscorrectos,consulteeldocumento“Instrucciones delvehículoconASWC-1”queseencuentraenelsitioweb axxessinterfaces.com. 4) VerifiquequeloscablesconectadosdelASWC-1alvehículo seconectendirectamente,esdecir,soldadura,tapaderosca, empalmedeuniónoccidental.Nosepermiteelusodeconectoresde tiporoscaoconectoresatopedebidoaqueaumentanlaresistencia. 16 Resolución de problemas de ASWC-1 Modo de detección automática Nota: Si se usa un arnés precableado y ha intentado todos los pasos de resolución de problemas mencionados anteriormente, si foco LED del ASWC-1 aún no se enciende sin parpadear, retire el arnés precableado del ASWC-1 y use el arnés que venía con el ASWC-1. Siharealizadocualquieradelospasosanteriores,vuelvaaprogramar elASWC-1presionandoelbotónderestablecimientoenelASWC-1 durante3segundos,suélteloyluegosigalasinstruccionesenlapágina 9empezandoapartirdelpaso3.SielfocoLEDdelASWC-1aúnnose enciendesinparpadearalfinal,consulteelmododeprogramaciónmanual enlaspáginas19a21paraprogramarelASWC-1manualmente. SielfocoLEDdelASWCseenciendesinparpadearperoaúnno funciona,sigaestospasospararesolverlosproblemasdelapartede programacióndelradiosobrelasecuenciadeprogramación: 1) Confirmequeelconectorde3.5mmenelASWC-1estéconectado firmementeasuradioyqueestéenelconectorcorrectodelradio. Asegúresedequenoestéconectadoalconectoraux,micoBluetooth. Sinoestáseguroquéconectordebeconectaralradio,comuníquese conelproveedordelradio.Siseconectóelconectorequivocadodel radio,corríjaloyluegovuelvaaprogramarelASWC-1. Nota: Algunos radios no usan un conector para los controles en el volante más bien usan un cable. Si es así, consulte la sección de conexiones que se deben hacer (pág. 6) y asegúrese de que haya conectado los cables correctos. 2) Siestáusandounradioconuncableparalasconexionesenvez deunconector,asegúresedequetambiénhayaprogramadolos controlesenelvolantealradiosiguiendolasinstruccionesquese incluyenconelradio.Comuníqueseconelproveedordelradiosi tienecualquierdudasobreesto. Nota: Esto no aplica a los radios JVC y Kenwood. 17 Resolución de problemas de ASWC-1 Modo de detección automática 3) Para los radios Kenwood, asegúresedequeelASWC-1muestre queseestáusandounradioKenwood,consulteleyendadelradio (pág.21).SialcontrariolaleyendadelradiomuestraradioJVC, entoncesconsulteelcambiodetipoderadio(pág.12)paraobligar alprogramadelASWC-1amostrarKenwood. Sugerencia: Algunos radios Kenwood tienen una función llamada Sensor de control remoto. Si su radio tiene esta función, asegúrese de que está encendida. Si está encendida, apáguela y vuélvala a encender. 4) Para radios Alpine, retireelconectorde3.5mmdelradio,vuelva aprogramarelASWC-1sinelconector,yluegovuelvaaconectarel conectorde3.5denuevoconelradio. Sugerencia: Algunos radios Alpine tienen una función que cambia el control remoto a la parte posterior o frontal. Si tiene uno de estos radios, asegúrese de que el sensor esté en el ajuste trasero. Si el ajuste está en la parte trasera, cámbielo a la parte frontal y luego de nuevo a la parte trasera. 5) Para radios Pioneer y Sony, sielASWC-1funcionaperolos botonesnoestánfuncionandoodejandefuncionar,estopodría deberseaqueelconectorde3.5mmdelASWC-1noestábien colocado,seestádesconectandoohaysuciedadenloscontactos. Además,algunasvecesestopuedeserintermitente.Retiretodala suciedaddeloscontactos,vuelvaainsertarelconectorfirmemente enelradioyluegocoloqueunbucleenelcablede3.5mmpara evitarqueestosucedaenelfuturo.Asimismo,sialgoestáevitando queelconectorentreporcompleto,talcomoundisipador,recorte ligeramenteunpocoelplásticodelconectorde3.5según seanecesario. 18 Resolución de problemas de ASWC-1 Modo de programación manual Sisuvehículonoseencuentraenlalistadeladetecciónautomáticadel ASWC-1enelsitiowebdeAxxess,www.axxessinterfaces.com,esposible quepuedaprogramarmanualmenteunvehículosincomunicaciónde dadosusandolossiguientespasos. Sugerencia: En caso de no saber si tiene un vehículo con comunicación de datos, consulte el documento “Instrucciones del vehículo con ASWC-1” en el sitio web www.axxessinterfaces. com. Si indica presionar y soltar el botón de aumentar volumen repetidamente para programar el ASWC-1, entonces usted tiene un vehículo con comunicación de datos. Nota: No todos los radios tendrán todos los comandos posibles en control en el volante. Los radios de mercado secundario que no tengan Bluetooth no reconocerán los comandos PPT (presionar para hablar) o de teléfono colgado o descolgado; sin embargo, estos botones pueden programarse manualmente para realizar otros comandos. Consulte el manual del propietario del radio o el proveedor del radio para ver los comandos específicos que el radio puede reconocer. Nota: Lea todos los pasos de programación manual antes de comenzar. 1) Sigalospasosenlaseccióndeconexionesquesedebenhacer (pág.6y7)paraconectarloscablesdelASWC-1consuradio. 2) Enciendalaignición,luegopresioneymantengapresionadoelbotón derestablecimientoenelASWC-1duranteaproximadamente10 segundoshastaqueelfocoLEDdelASWC-1parpadeelentamentey luegosuelteelbotónderestablecimiento. 3) Enestemomento,presioneymantengapresionadoelbotónde aumentar volumenenelvolantedurante7segundoshastaque elfocoLEDseenciendasinparpadear.Ahorasuelteelbotónde aumentar volumenyelfocoLEDseapagará.Yaquedóprogramado elbotónquesubeelvolumen. 19 Resolución de problemas de ASWC-1 Modo de programación manual 4) Ahorapresioneymantengapresionadoelbotóndebajar volumen hastaqueelfocoLEDseenciendasinparpadear.Suelteelbotónde bajar volumenyelfocoLEDseapagará,yaquedóprogramadoel botóndebajar volumen. 5) Enestemomentoconsultelaleyendadeprogramaciónmanual(pág. 21)ycontinúeconelbotónBuscar siguiente. Nota: Para cualquier comando que necesite omitirse, presione el botón de aumentar volumen por cada uno. El foco LED debe encenderse cada vez que presione el botón de aumentar volumen. 6) Despuésdeprogramarelúltimobotónenelvolante,presione ymantengapresionadoelbotóndeaumentar volumenhastaque elfocoLEDparpadeelentamenteyluegosuelteelbotónde aumentar volumen. Nota: Si en cualquier momento se equivoca, mantenga presionado el botón de restablecimiento en el ASWC-1 durante 10 segundos o más. Esto reiniciará la programación manual. Vuelva al Paso 4 y empiece de nuevo. 7) Presioneymantengapresionadoelbotóndebajar volumenhasta queelfocoLEDempieceaparpadearrápidamente. 8) Suelteelbotóndebajar volumen. 9) Despuésdeaproximadamente4segundosdequeelfocoLED parpadeerápidamente,esteseapagarádurante2segundos. 10) LuegoelfocoLEDparpadearáhasta15veces,dependiendodel radioalqueelASWC-1estáconectado. 11) Asegúresedequelacantidaddeparpadeoscorrespondaalradio quetieneinstalado.Consultelaleyendadelradio(pág.13). 20 Resolución de problemas de ASWC-1 Modo de programación manual Nota: Si el número de parpadeos no coincide con el radio que ha instalado, consulte la sección de cambio de tipo de radio (pág. 13). 12) Presioneymantengapresionadoelbotóndebajar volumenhasta queelfocoLEDseiluminesinparpadear. 13) Laprogramacióndelvehículoydelradiohafinalizado.Ahora, pruebelasfuncionesdelcontrolenelvolanteparaasegurarsede quefuncionencorrectamente. Leyenda de la programación manual 1.Subirvolumen 10.Banda 2.Bajarvolumen 11.Reproducir/Aceptar 3.Buscarsiguiente 12.PTT(presionarparahablar) 4.Buscaranterior 13.Colgado 5.Fuente/Modo 14.Descolgado 6.Silencio 15.Aumentarventilador 7.Subirprestablecido 16.Disminuirventilador 8.Bajarprestablecido 17.Aumentartemperatura 9.Encendido 18.Disminuirtemperatura 21 Resolución de problemas de ASWC-1 Restablecimiento de los ajustes originales de ASWC-1 1) Enciendalaigniciónyespere3segundos. 2) Presioneelbotónderestablecimientodurante3segundosy luegosuéltelo. 3) Consultelaseccióndeprogramación(páginas8y9)para programarelASWC-1. 4) DespuésqueelfocoLEDseenciendasinparpadear,elASWC-1se restablecióydebefuncionarconlosajustespredeterminados. Resolución de problemas de ASWC-1 Retroalimentación LED A. Retroalimentación LED del vehículo (indicadaporelfocoLED decolorverdeenelASWC-1) El1er El2o El3er El4o El5o El6o El7o parpadeodelfocoLEDeselblanco/verde parpadeodelfocoLEDeselamarillo/verde parpadeodelfocoLEDeselverde/anaranjado parpadeodelfocoLEDeselgris/rojo parpadeodelfocoLEDeselnegro/verde parpadeodelfocoLEDeselgris/azul parpadeodelfocoLEDeselrosa Nota (section A): • Los parpadeos cortos representan el o los cables del control en el volante que no están conectados al vehículo desde el ASWC-1. • Los parpadeos largos representan el o los cables que están conectados al vehículo. 22 Resolución de problemas de ASWC-1 Retroalimentación LED B. Retroalimentación LED del radio (indicadaporelfocoLEDde colorrojoenelASWC-1) El1er El2o El3er El4o El5o El6o El7o El8o El9o El10o El11vo El12vo El13vo El14vo El15vo parpadeodelfocoLEDesparaEclipse(Tipo1) parpadeodelfocoLEDesparaKenwood parpadeodelfocoLEDesparaClarion(Tipo1) parpadeodelfocoLEDesparaSonyyDual parpadeodelfocoLEDesparaJVC parpadeodelfocoLEDesparaPioneeryJensen parpadeodelfocoLEDesparaAlpine* parpadeodelfocoLEDesparaVisteon parpadeodelfocoLEDesparaValor parpadeodelfocoLEDesparaClarion(Tipo2) parpadeodelfocoLEDesparaMetraOE parpadeodelfocoLEDesparaEclipse(Tipo2) parpadeodelfocoLEDesparaLG parpadeodelfocoLEDesparaParrot** parpadeodelfocoLEDesparaXITE *Nota (sección B): Si el ASWC-1 parpadea 7 veces y no tiene un radio Alpine conectado a él, esto significa que el ASWC-1 no detectó ningún radio conectado. Verifique que el conector de 3.5mm esté conectado a la entrada del control en el volante en el radio. **Nota (sección B): Se requiere de AX-SWC-PARROT (se vende por separado). El radio debe estar actualizado a la versión 2.1.4 o más reciente en www.parrot.com y el ASWC-1 debe estar actualizado al firmware más reciente del sitio web www.axxessinterfaces.com. 23 INSTRUCCIONES DE INSTALACIÓN ASWC-1 ADVERTENCIA IMPORTANTE Esteproductoincluyeinstruccionesdeinstalaciónquedebenseguirse cuidadosamente.Dichasinstruccionesestánredactadasdandopor supuestoqueelinstaladorescapazdecompletarestostiposde instalacioneselectrónicas.Sitienedudasrespectodeloquesele indicaquehagaocreequenocomprendelasinstruccionescomopara completarlainstalaciónenformaadecuadaysegura,debeconsultara untécnicoqueefectivamentetengaestosconocimientosycomprensión. Si no sigue estas instrucciones con cuidado y no instala la interfaz como se describe, podría provocar daños en el vehículo o en los sistemas de seguridad del vehículo. La interferencia con determinados sistemas de seguridad también podría provocar daños a las personas. Si tiene alguna pregunta al respecto, llame a la línea de ayuda o a metra, al 1-800-221-0932 para obtener asistencia. REV. 4/15/2014 ASWC-INST10 CONOCIMIENTO ES PODER KEL NOWLEDGE IS POWER Mejoresushabilidadesdeinstalaciónyfabricación Enhance your installation and fabrication skills by inscribiéndoseenlaescueladedispositivos enrolling in the most recognized and respected mobile electronics school in our industry. electrónicosmóvilesmásreconocidayrespetadade Log onto www.installerinstitute.com or call nuestraindustria.Regístreseenwww.installerinstitute. 800-354-6782 for more information and take steps comollameal800-354-6782paraobtenermás toward a better tomorrow. informaciónyavancehaciaunfuturomejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). US.PAT.NOS.8014920y8214105 1-800-221-0932 AxxESSINTERfACES.COM © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION