Download ECH-PCI-CE-H13A
Transcript
PC-HELPER PCI Bus Expansion Chassis Short x 4Slots ECH-PCI-CE-H4A Short x 7Slots ECH-PCI-CE-H7A Short x 13Slots ECH-PCI-CE-H13A User’s Manual CONTEC CO.,LTD. Check Your Package Thank you for purchasing the CONTEC product. The product consists of the items listed below. Check, with the following list, that your package is complete. items, contact your retailer If you discover damaged or missing Product Configuration List - Expansion chassis(One of the following) …1 [ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A] - Bracket fixed screw for rack-mounted …4 - Bracket for rack-mounted …2 - Power cable …1 - Slot cover(One of the following) ECH-PCI-CE-H4A …4, ECH-PCI-CE-H7A …7, ECH-PCI-CE-H13A …13 - Board fixed screw(One of the following) ECH-PCI-CE-H4A …4, ECH-PCI-CE-H7A …7, ECH-PCI-CE-H13A …13 - Rubber feet …4 - This User’s Manual …1 CONTEC Board fixed screw Expansion chassis Power cable Slot cover Rubber feet User’s Manual Bracket fixed screw for rack-mounted User’s Manual Bracket for rack-mounted ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A i Copyright Copyright 2008 CONTEC CO., LTD. ALL RIGHTS RESERVED. No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD. CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this document. The information in this document is subject to change without notice. All relevant issues have been considered in the preparation of this document. Should you notice an omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD. Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear in this document or for results obtained by the user as a result of using this product. Trademarks MS, Microsoft, Windows, Windows NT and MS-DOS are trademarks of Microsoft Corporation. brand and product names are trademarks of their respective holder. ii Other ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A Table of Contents Check Your Package ................................................................................................................................ i Copyright .................................................................................................................................................ii Trademarks ..............................................................................................................................................ii Table of Contents ...................................................................................................................................iii 1. BEFORE USING THE PRODUCT 1 About the Chassis.................................................................................................................................... 1 Features............................................................................................................................................. 1 Expansion adapter (Option)............................................................................................................. 1 Combinations of Expansion Adapters and Expansion Chassis ...................................................... 2 Restrictions....................................................................................................................................... 3 Customer Support.................................................................................................................................... 4 Web Site ........................................................................................................................................... 4 Limited One-Year Warranty ................................................................................................................... 4 How to Obtain Service............................................................................................................................ 4 Liability ................................................................................................................................................... 4 Safety Precautions ................................................................................................................................... 5 Safety Information .................................................................................................................................. 5 Handling Precautions ....................................................................................................................... 5 Environment ..................................................................................................................................... 7 Inspection ......................................................................................................................................... 7 Storage.............................................................................................................................................. 7 Disposal ............................................................................................................................................ 7 2. SETUP 9 What is Setup?......................................................................................................................................... 9 Step 1 Preparation ................................................................................................................................... 9 Items to be prepared....................................................................................................................... 10 Names of major parts ..................................................................................................................... 11 Step 2 Installing the Expansion Board ................................................................................................. 12 Step 3 Connecting the Connection Cable............................................................................................. 13 Connecting the connection cable to the expansion adapter.......................................................... 13 Connecting the connection cable to the ECH-PCI-CE-H4A/H7A/H13A.................................... 13 Plugging the Power Cable ............................................................................................................. 13 Step 4 Installing the expansion adapter board ..................................................................................... 14 Step 5 Setup and Check ........................................................................................................................ 14 Starting the system ......................................................................................................................... 14 Setting up the hardware in Windows ............................................................................................ 15 Checking the hardware in Windows ............................................................................................. 15 Attaching Rack Mount Brackets........................................................................................................... 16 Setup Troubleshooting .......................................................................................................................... 17 Symptoms and Actions .................................................................................................................. 17 If your problem cannot be resolved............................................................................................... 17 ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A iii 3. ABOUT HARDWARE 19 Hardware specification ..........................................................................................................................19 Physical Dimensions..............................................................................................................................21 iv ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 1. Before Using the Product 1. Before Using the Product This chapter provides information you should know before using these products. About the Chassis These products are an expansion chassis that adds PCI bus slots of PC. Connecting an optional expansion adaptor (EAD-CE-LPE, EAD-CE-EC) can add PCI bus slots to the PC. Mountable board is short-type PCI bus board (176.5(L) x 107(H) mm). You can link the ON/OFF control of the chassis to that of your PC. Features - PCI (5V/32bit 33MHz) bus slots can be added to your PC. PCI (5V/32bit 33MHz) bus slots can be added to your PC. ECH-PCI-CE-H4A : PCI bus slots (x 4) can be added. ECH-PCI-CE-H7A : PCI bus slots (x 7) can be added. ECH-PCI-CE-H13A : PCI bus slots (x 13) can be added. This expansion chassis is connected to a PC using an optional expansion adapter. - Short-type PCI bus boards can be connected. You can connect short-type [176.5 (L) x 107 (H) mm] PCI bus boards. ECH-PCI-CE-H4A : PCI bus boards (x 4) can be added. ECH-PCI-CE-H7A : PCI bus boards (x 7) can be added. ECH-PCI-CE-H13A : PCI bus boards (x 13) can be added. - ON/OFF control of the chassis can be linked to that of your PC. You can link the ON/OFF control of the expansion chassis to that of your PC. - Steel chassis with cooling fan Steel chassis with cooling fan suitable for use in fields - Rack-mountable Rack-mountable with supplied brackets Expansion adapter (Option) Expansion Adapter for Express Card Slot Expansion Adapter for PCI Express Slot : : EAD-CE-EC EAD-CE-LPE Check the CONTEC’s Web site for more information on these expansion adapters. ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 1 1. Before Using the Product Combinations of Expansion Adapters and Expansion Chassis The expansion adapters and expansion chassis can be used in the following combinations: Expansion chassis Expansion adapter ECH-PCI-CE -H2B -F2B -H4B -F4B -H4A -H7A EAD-CE-EC Ο Ο Ο Ο Ο x -H13A x EAD-CE-LPE Ο Ο Ο Ο Ο Ο Ο Expansion chassis ECH-PCI-CE-H2B ECH-PCI-CE-F2B ECH-PCI-CE-H4A ECH-PCI-CE-H7A ECH-PCI-CE-H4B ECH-PCI-CE-F4B ECH-PCI-CE-H13A Expansion adapter EAD-CE-EC 2 EAD-CE-LPE ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 1. Before Using the Product Restrictions These products are used in a combination with the optional expansion adapter. The following restrictions apply to the situation when the expansion adapter is connected to the expansion chassis. These products have restrictions on the types of PCs and boards that can be used. Be sure to check the following restrictions before use. < Restrictions of PC > These products use the PCI-to-PCI Bridge to extend the bus. The PCI boards plugged in PCI slots in these products are recognized if the PCI-to-PCI bridge is recognized by the BIOS in the PC used. Ask the PC vendor for whether the BIOS recognizes the PCI-to-PCI bridge. < Restrictions on transfer rate > When the expansion chassis accommodates a board that performs high-speed transfer such as bus mastering, the overall transfer rate may be lower than that of PCI bus slots in the main unit of a desktop PC. This is caused by bus extension by the PCI-to-PCI Bridge. The transfer rate may vary with the system configuration and the type of the PC. < Restrictions of PCI board > None of the following boards can be plugged into any expansion slot in these products. - Video display board (VGA board) - Board to connect a PCI bus expansion chassis - Board explicitly stated not to be used with the PCI-to-PCI Bridge - Some boards, even PCI bus-compliant ones, may not work depending on their specifications ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 3 1. Before Using the Product Customer Support CONTEC provides the following support services for you to use CONTEC products more efficiently and comfortably. Web Site Japanese English Chinese http://www.contec.co.jp/ http://www.contec.com/ http://www.contec.com.cn/ Latest product information CONTEC provides up-to-date information on products. CONTEC also provides product manuals and various technical documents in the PDF. Free download You can download updated driver software and differential files as well as sample programs available in several languages. Note! For product information Contact your retailer if you have any technical question about a CONTEC product or need its price, delivery time, or estimate information. Limited One-Year Warranty CONTEC products are warranted by CONTEC CO., LTD. to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser. Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from which it was purchased. This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and original products. The warranty is not applicable if the device has been tampered with or damaged through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in which case repairs will be considered beyond the warranty policy. How to Obtain Service For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you purchased before returning any product. * No product will be accepted by CONTEC group without the RMA number. Liability The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from Safety Precautions. Understand the following definitions and precautions to use the product safely. 4 ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 1. Before Using the Product Safety Precautions Understand the following definitions and precautions to use the product safely. Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources. Understand the meanings of these labels to operate the equipment safely. DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or in property damage. Handling Precautions DANGER Do not use the product where it is exposed to flammable or corrosive gas. an explosion, fire, electric shock, or failure. Doing so may result in CAUTION - - - Do not plug or unplug any board into or from an expansion slot with the PC or these products powered. Doing so may result in a malfunction, overheating, or fault. Be sure to turn off the PC or these products and unplug their power cables before plugging or unplugging any expansion board. Do not plug or unplug the cable interconnecting the PC and the expansion chassis with the PC or these products powered. Do not turn on or off the power switch of these products with the PC powered. Doing so may result in a malfunction. The total current consumption by the boards installed in the expansion slots in these products must not exceed the maximum power capacity of its power supply. Failure to supply ample power to expansion boards could result in a malfunction, overheating, or fault. The external supply voltage or drive current must not exceed the rating. Do not connect any signal other than specified to the on-board connector. Doing so may result in a malfunction, overheating, fault, or damage. If a specific expansion slot is recommended for a board, plug the board into that slot. Failure to do so may result in a malfunction, overheating, fault, or damage. When plugging or unplugging the power cable, be sure to hold it by the plug itself. ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 5 1. Before Using the Product - - - - - Since the I/O expansion chassis is a precision device, do not store or use it where it is subject to shock or vibration. Also avoid any place where the chassis is exposed to direct sunlight, extremely high humidity, or much dust. Do not use or store the chassis where it is exposed to any chemical either directly or as vapor in the air. The chassis has ventilating slits to prevent it from overheating. Avoid using the chassis with the ventilating slits blocked or in an ill-ventilated place. Do not use the chassis near equipment generating a strong magnetic field or noise. Doing so may result in a malfunction, overheating, fault, or damage in the chassis, your PC, or both. It is very dangerous to use the chassis with water, liquid, or metal (conductive) chips left inside. Be careful not to let such foreign matters in the chassis. The specifications of these products are subject to change without notice for enhancement or quality improvement. Even when using these products continuously, be sure to read the manual and understand the contents. Do not modify these products. CONTEC will bear no responsibility for any problems, etc., resulting from modifying these products. Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever (including damages for loss of business profits) arising out of the use of or inability to use this CONTEC product or the information contained herein. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 6 ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 1. Before Using the Product Environment Use this product in the following environment. may overheat, malfunction, or cause a failure. If used in an unauthorized environment, the chassis Operating temperature 0 - 50°C Humidity 20 - 80%RH (No condensation) Corrosive gases None Floating dust particles Not to be excessive Inspection Inspect the product periodically as follows to use it safely. - Ventilating slits must neither be blocked nor have dust or foreign matters adhering. Front view Right side view CONTEC The illustration above is of the ECH-PCI-CE-H4A but the check points are the same as with the ECH-PCI-CE-H7A/H13A. Storage When storing this product, keep it in its original packing form. (1) Wrap it in the packing material, then put it in the box. (2) Store the package at room temperature at a place free from direct sunlight, moisture, shock, vibration, magnetism, and static electricity. Disposal When disposing of the product, follow the disposal procedures stipulated under the relevant laws and municipal ordinances. ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 7 1. Before Using the Product 8 ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 2. Setup 2. Setup This chapter explains how to set up the chassis. Refer to the user’s manual for the expansion adapter EAD-CE-EC, EAD-CE-LPE as required. What is Setup? Setup means a series of steps to take before the product can be used. Taking the following steps in this chapter sets up the ECH(PCI)BE-H4A/H7A/F7A/H13A/F13A. Step 1 Preparation Step 2 Installing the Expansion Board Step 3 Connecting the Connection Cable Step 4 Installing the expansion adapter board Step 5 Setup and Check If setup fails to be performed correctly, refer to “Setup Troubleshooting”. Step 1 Preparation Configuration image The photo is of the EAD-CE-LPE, ECH-PCI-CE-H4A. Figure 2.1. Configuration image ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 9 2. Setup Items to be prepared - PC - Expansion adapter [EAD-CE-LPE,EAD-CE-EC] Expansion adapter board [One of BUS-AD1C-LPE, BUS-PC-EC] …(a), Connection Cable[CB-CE1] …(b) - Expansion chassis - PCI board to be installed Chassis [ECH-PCI-CE-H4A/H7A/H13A] …(c), Power cable (c) (b) (a) The photo is of the EAD-CE-LPE+ECH-PCI-CE-H4A but the check points are the same as with the ECH-PCI-CE-H7A/H13A. 10 ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 2. Setup Names of major parts ECH-PCI-CE-H4A Front view Back view CONTEC POWER LED FAN Expantion slots AC Inlet BUS-PAC-PCI-CE Input voltage select switch(AC115V/AC230V) POWER Switch Figure 2.2. Names of major parts < ECH-PCI-CE-H4A > ECH-PCI-CE-H7A Front view Back view CONTEC Expantion slots POWER LED AC Inlet FAN POWER Switch Figure 2.3. Names of major parts BUS-PAC-PCI-CE Input voltage select switch(AC115V/AC230V) < ECH-PCI-CE-H7A > ECH-PCI-CE-H13A Front view Back view Expantion slots BUS-PAC-PCI-CE AC Inlet POWER LED FAN POWER Switch Figure 2.4. Names of major parts Input voltage select switch(AC115V/AC230V) Main power switch < ECH-PCI-CE-H13A > ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 11 2. Setup Step 2 Installing the Expansion Board CAUTION Before installing an expansion board on these products, be sure to turn off your PC or these products and unplug the power cables from wall outlets. Follow the procedure below to install the expansion board on these products. (1) Unplug the power cable and connection cable from these products. (2) Remove screw (H4A : two, H7A/13A : three) from the top of the rear panel, then remove the chassis cover by sliding it to the rear side (in the order of arrows 1 and 2). 1 Cover 2 The photo is of the ECH-PCI-CE-H4A. Figure 2.5. Installing the Expansion Board (3) Plug the expansion board into a PCI Express bus slot and fasten the bracket with the attached screw. Apply slot covers to unused slots and fasten them with screws. (4) Put the chassis cover back in place and fasten it with the removed screws. 12 ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 2. Setup Step 3 Connecting the Connection Cable Connecting the connection cable to the expansion adapter Refer to the user’s manual for the expansion adapter EAD-CE-EC and EAD-CE-LPE to connect its connection cable to the expansion adapter. Connecting the connection cable to the ECH-PCI-CE-H4A/H7A/H13A Connect the connection cable [CB-CE1] to the interface connector of the ECH-PCI-CE-H4A/H7A/H13A. See “Names of Major Parts” in this chapter to confirm the location of the interface connector. Lock the screws. The photo is of the ECH-PCI-CE-H4A. Figure 2.6. Connecting the PC to the ECH-PCI-CE-H4A CAUTION Do not plug the connection cable into any other connector as doing so can cause a fault. Plugging the Power Cable (1) Plug the power cable into the ECH-PCI-CE-H4A/H7A/H13A. The photo is of the ECH-PCI-CE-H4A. Figure 2.7. Plugging the power cable into the ECH-PCI-CE-H4A (2) Plug the power cable into a wall outlet. ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 13 2. Setup Step 4 Installing the expansion adapter board Refer to the user’s manual for the expansion adapter (EAD-CE-EC and EAD-CE-LPE) to install the expansion bus adapter on the PC. Step 5 Setup and Check Starting the system The ECH-PCI-CE-H4A/H7A/H13A is turned on and off in sync with the PC’s power supply. the PC detects the expansion adapter, these products are turned on. When Turning on the system (1) Plug the power plug of these products into a wall outlet. You do not need to press the POWER switch on the front panel (*1). (2) The power supply of a PC is turned ON. (3) As soon as the expansion adapter is recognized by the PC, these products are turned on automatically. (4) Make sure that the POWER LED on these products are on. Turning off the system (1) The power supply of a PC is turned OFF. (2) These products are turned off in synchronization with the PC’s power supply. (*1) Pressing the POWER switch on the front panel of the ECH-PCI-CE-H4A/H7A/H13A turns on these products or puts it to sleep. Use the switch, for example, to turn on only the ECH(PCI)BE-H4A/H7A/F7A/H13A/F13A. CAUTION Do not turn on or off these products with the PC main unit powered. Doing so cancels the detection of the bus adapter. When turning these products on back, restart the PC main unit. 14 ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 2. Setup Setting up the hardware in Windows At startup of Windows, the PCI-to-PCI Bridge used by these products are detected in sequence and identified automatically by the Windows standard driver. After that, the PCI boards installed on these products are detected in sequence. For setting up and checking the boards used on the expansion chassis, refer to their respective manuals. Checking the hardware in Windows You can use Device Manager to check whether these products have been identified in Windows. Device Manager shows “PCI standard PCI-to-PCI bridge” and “Intel 21152 PCI to PCI bridge” under “System devices”. You can check these products currently being used by the number of entries of “PCI standard PCI-to-PCI bridge” and “Intel 21152 PCI to PCI bridge”. One entry Two entries Four entries : ECH-PCI-CE-H4A : ECH-PCI-CE-H7A : ECH-PCI-CE-H13A Figure 2.8. Sample screen shot of Device Manager (ECH-PCI-CE-H7A) CAUTION The expansion chassis does not depend on the OS in use. ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 15 2. Setup Attaching Rack Mount Brackets These products can be rack mounted using the attached brackets. The brackets can be used in two ways as illustrated below. Rack-mount these products using the brackets by the appropriate method suitable for the operating environment. < Vertically placed > CONTEC < Horizontally placed > CONTEC The photo is of the ECH-PCI-CE-H4A but the check points are the same as with the ECH-PCI-CE-H7A/H13A. Figure 2.9. Attaching the Rack Mount Brackets 16 ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 2. Setup Setup Troubleshooting Please confirm followings when these products do not work. Symptoms and Actions The chassis won’t be turned on. a. Make sure that the power cable has been connected correctly. b. Make sure that the power supplies of the PC and these products are on. c. Make sure that you have followed the procedure in Chapter 2. d. Even though the chassis is still not turned on, check whether it is turned on with no board installed. If the chassis is turned on with no board installed, check the total current consumption by the installed boards. The total current consumption must not exceed the power capacity of these products. No PCI board on these products are detected. e. Make sure that the expansion adapter board has been installed correctly. f. Make sure that the connection cable has been installed correctly. When connecting the connection cable to the main chassis, insert the connector until it clicks into place. g. Make sure that the POWER LED on these products are turned on. a f f e The photo is of the EAD-CE-LPE+ECH-PCI-CE-H4A but the check points are the same as with the ECH-PCI-CE-H7A/H13A. If your problem cannot be resolved Contact your retailer. ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 17 2. Setup 18 ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 3. About Hardware 3. About Hardware Hardware specification Table 3.1. Specification Item Compatible bus ECH-PCI-CE-H4A ECH-PCI-CE-H7A ECH-PCI-CE-H13A PCI Local Bus Specification Rev2.3 (+5V type) Address space 32-bit memory address, I/O address Interrupt level INTA - INTD Bus operating clock 33MHz (Max.) Number of user-available 4 slots 7 slots 13 slots slots (short size) (short size) (short size) Acceptable board sizes 176.5(L) x 107(H) 176.5(L) x 107(H) 176.5(L) x 107(H) (mm) Power supply Expansion slot +5VDC 11.3A (Max.) +5VDC supplied power +3.3VDC 6A (Max.) +3.3VDC 15A (Max.) *2 +12VDC 3A (Max.) +12VDC 9A (Max.) -12VDC 0.7A (Max.) -12VDC 0.8A (Max.) (The output current must not exceed the value on the right.) 18A (Max.) *2 Maximum total power 130W *3 0 - 30 ºC : 230W capacity 30 - 40 ºC : 205W 40 - 50 ºC : 175W *4 AC input line voltage 115/230VAC (selecting switch) *1 AC line frequency 50 - 60Hz AC power input 3A(115VAC)/1.5A(230VAC) 6A(115VAC)/4A(230VAC) current Physical dimensions 210.0(W) x 138.0(H) x 300.0(W) x 138.0(H) x 424.0(W) x 156.0(H) x (mm) 235.0(L) (No fittings) 255.0(L) (No fittings) 255.0(L) (No fittings) Weight 3.5 kg 5.0 kg 7.5 kg AC cable 2.5m 3P *1 : *2 : AC input line voltage range : 90 - 132VAC/180 - 250VAC The sum of +5VDC and +3.3VDC must not exceed 90W. *3 : Condition with CE marking: 130W at 40ºC. *4 : Condition with CE marking: 175W at 50ºC. Physical dimensions of acceptable board (Max.) 107(H) 176.5(L) [mm] ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 19 3. About Hardware Table 3.2. Environmental specification Item Specification Operating temperature 0 - 50ºC Operating humidity 20 - 80%RH (No condensation) Storage temperature 0 - 60ºC Storage humidity 10 - 90%RH (No condensation) Floating dust particles Not to be excessive Corrosive gases None CAUTION The power supply and cooling fan in these products are consumables, requiring replacement after use for a certain period of time. Although each of the parts should be replaced after use for the following period of time in principle, the life may be shortened depending on the operating environment. Keep in mind that the lives of the parts may be extremely shortened if they are used where it is either exposed to must dirt, metal chips or particles, or dust or affected by oil or corrosive gas. - Power supply : About 5 years (in an office environment kept at a temperature of 25°C and a humidity of 60%) 20 - Fan : About 5 years (in an office environment kept at a temperature of 25°C and a humidity of 60%) - Fan Filter : About 1 year (in an office environment kept at a temperature of 25°C and a humidity of 60%) ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 3. About Hardware Physical Dimensions CAUTION - When using this chassis, keep it at least 20mm away from any object such as the wall for cooling purposes. - Attaching rubber feet to the chassis makes it 3.6mm taller. 90 140 90 235 215 15 R2.5 R4.5 229 245 4-φ5 AIR OUT FAN AIR FLOW FAN 138 210 POWER 10 [mm] Figure 3.1. Physical Dimensions < ECH-PCI-CE-H4A, Horizontally placed > 157 173 R4.5 R2.5 15 140 90 90 215 4-φ5 138 10 210 P OWER 235 [mm] Figure 3.2. Physical Dimensions < ECH-PCI-CE-H4A, Vertically placed > ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 21 3. About Hardware 90 255 215 90 140 15 R2.5 R4.5 319 335 4-φ5 300 AIR OUT FAN 138 AIR FLOW FAN POWER 10 [mm] Figure 3.3. Physical Dimensions < ECH-PCI-CE-H7A, Horizontally placed > 157 173 R4.5 R2.5 15 140 90 215 255 4-φ5 138 10 300 POWER 90 [mm] Figure 3.4. Physical Dimensions < ECH-PCI-CE-H7A, Vertically placed > 22 ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 3. About Hardware 90 255 215 90 140 15 R2.5 R4.5 443 459 424 4-φ5 AIR OUT FAN 156 AIR FLOW FAN POWER 10 [mm] 175 191 Figure 3.5. Physical Dimensions < ECH-PCI-CE-H13A, Horizontally placed > R4.5 R2.5 90 140 90 4-φ5 215 255 156 10 424 POWER 15 [mm] Figure 3.6. Physical Dimensions < ECH-PCI-CE-H13A, Vertically placed > ECH-PCI-CE-H4A, ECH-PCI-CE-H7A, ECH-PCI-CE-H13A 23 ECH-PCI-CE-H4A ECH-PCI-CE-H7A ECH-PCI-CE-H13A User’s Manual CONTEC CO., LTD. July 2007 Edition 3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan Japanese http://www.contec.co.jp/ English http://www.contec.com/ Chinese http://www.contec.com.cn/ No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD. [07162008] [07162008] Management No. A-51-607 Parts No. LYJR031