Download Z8 Encore! 8K/4K MCU Evaluation Board User Manual - Digi-Key
Transcript
Z8F08200100KIT Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual UM015004-1105 ZiLOG Worldwide Headquarters • 532 Race Street • San Jose, CA 95126-3432 Telephone: 408.558.8500 • Fax: 408.558.8300 • www.ZiLOG.com Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual ii This publication is subject to replacement by a later edition. To determine whether a later edition exists, or to request copies of publications, contact: ZiLOG Worldwide Headquarters 532 Race Street San Jose, CA 95126-3432 Telephone: 408.558.8500 Fax: 408.558.8300 www.ZiLOG.com Document Disclaimer ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other products and/or service names mentioned herein may be trademarks of the companies with which they are associated. ©2005 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded. ZiLOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZiLOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. Except with the express written approval of ZiLOG, use of information, devices, or technology as critical components of life support systems is not authorized. No licenses are conveyed, implicitly or otherwise, by this document under any intellectual property rights. Disclaimer UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual iii Safeguards The following precautions must be observed when working with the devices described in this document. Caution: Always use a grounding strap to prevent damage resulting from electrostatic discharge (ESD). Revision History Date Revision Level Description November 04 2005 Disclaimer Page # Removed the word Preliminary from all page footers and updated All trademarks. UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual iv Table of Contents Safeguards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v List of Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Software (on CD-ROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 System/Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Supported Host System Configuration . . . . . . . . . . . . . . . . . . . . . . . .3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Z8 Encore! 8K/4K Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 UART with IrDA Endec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Power and Communication Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . .9 External Interface Headers JP1 and JP2 . . . . . . . . . . . . . . . . . . . . . . . . .10 Schematics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Table of Contents UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual v List of Figures Figure 1. Figure 2. Z8 Encore! MCU Evaluation Kit Contents . . . . . . . . . . . . . .2 Z8 Encore!® 8K/4K Evaluation Board . . . . . . . . . . . . . . . .6 List of Tables Table 1. List of Figures Jumpers JP3 and JP4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual 1 Introduction The Z8 Encore!® 8K/4K MCU is the part of the line of ZiLOG microcontroller products. The Z8 Encore! MCU Evaluation Kit (Z8F08200100KIT) enables users to become familiar with the hardware and software tools available with this product. This kit consists of the 8KB version of the Z8 Encore! evaluation board that supports and presents the features of the Z8 Encore! 8K/ 4K. This kit allows users to begin writing application software and contains all supporting documents. This manual acquaints users with the Z8 Encore! 8K/4K MCU Evaluation Kit, and gives instructions on setting up and using the tools to start building designs and applications. Kit Contents The Z8 Encore!® 8K/4K MCU Evaluation Kit contains the following: Hardware Introduction • • Z8 Encore!® 8K/4K Evaluation board • 5VDC power supply Smart Cable for PC to Z8 Encore! 8K/4K evaluation board (DB9 to six-pin male) UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual 2 Packaging CD-ROM Containing Documentation Power Supply Smart Cable Evaluation Board Figure 1. Z8 Encore! MCU Evaluation Kit Contents Software (on CD-ROM) • • • • ZDS II- Z8 Encore! IDE with ANSI C-Compiler Sample code Document browser Acrobat Reader install program Documentation • • Introduction Quick Start Guide Registration card UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual 3 • Z8 Encore!® 8K/4K technical documentation (on CD-ROM) – Evaluation Kit User Manual – ZDS II - IDE User Manual – eZ8 CPU User Manual – Product Specification – Product brief – Application notes – Programmer’s Reference Sheet The sample code is installed with ZDS II and resides in the <installation directory>\samples in the user's disk drive. The documentation can be installed by the user with the DemoShield interface or can be viewed on the CD-ROM using the DemoShield menus and a PDF reader. A copy of the Acrobat installer is provided on the CDROM and can be installed from the DemoShield install screen. After installing the documentation on the user’s system Windows Explorer can be used to select any document to be viewed with your favorite PDF file viewer. System/Software Requirements IBM PC (or compatible computer) with the following minimum configurations: Supported Host System Configuration Introduction • Win98 Second Edition, WinNT 4.0 Service Pack 6, Win2000 Service Pack 3, WinXP Service Pack 1 • • • • PentiumII/233MHz processor or higher up to Pentium IV, 2.8 GHz 96MB RAM or more 25MB hard disk space or more Super VGA video adapter UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual 4 • • Introduction CD-ROM One or more RS-232 communication ports UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual 5 Installation Follow the directions in the Quick Start Guide for software installation and setup of the Z8 Encore! evaluation kit. Installation UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual 6 Z8 Encore! 8K/4K Evaluation Board Introduction The Z8 Encore! 8K/4K evaluation board is an evaluation and prototyping board for the Z8 Encore! Z8 Encore! 8K/4K MCU. The board provides customers with a tool to evaluate features of Z8 Encore! 8K/4K MCU, and to start developing an application before building the hardware. TEST Y1 U6 RESET P2 J2 LEDs RS-232 Serial Port J1 Figure 14. Z8 Encore!® 8K/4K Evaluation Board Z8 Encore! 8K/4K Evaluation Board UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual 7 Features • • • • • • • • • • • • Z8 Encore!® MCU (28-pin SOIC) 3 LEDs RS-232 interface IrDA transceiver Two pushbuttons, RESET and TEST 5VDC power connector On-Chip Debugger interface Crsytal Oscillator at 18.432MHz Header for ADC input Prototyping area External interface connectors JP1 and JP2 2.7–3.6V operating voltage with 5V-tolerant inputs MCU The Z8 Encore!® 8K/4K MCU is member of a family of ZiLOG microcontroller products based upon the 8-bit eZ8 core CPU. The Flash in-circuit programming capability allows for faster development time and program changes in the field. The eZ8 core CPU is upward compatible with existing Z8® instructions. The rich peripheral set of the Z8 Encore! 8K/4K makes it suitable for a variety of applications including motor control, security systems, home appliances, personal electronic devices, and sensors. The evaluation board contains circuitry to support and present all the features of the Z8 Encore! 8K/4K. The main features of the Z8 Encore! 8K/ 4K are: Z8 Encore! 8K/4K Evaluation Board UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual 8 • • • • • • • • • • • • • • • • • eZ8 core CPU 8KB Flash memory with in-circuit programming capability 1KB register RAM 5-channel, 10-bit analog-to-digital converter (ADC) Full-duplex UART I2C interface (Master Mode only) Serial Peripheral Interface (SPI) Infrared Data Association (IrDA)-compliant infrared encoder/decoder Two 16-bit timers with capture, compare, and PWM capability Watch-Dog Timer (WDT) with internal RC oscillator Eleven or nineteen I/O pins Programmable priority interrupts On-Chip Debugger Voltage Brown-out Protection (VBO) Power-On Reset (POR) 2.7–3.6V operating voltage with 5V-tolerant inputs Operating temperatures: 20° ±10°C For further information on the Z8 Encore!® family of devices, consult the product specification, P/N PS0197, available for download from www.zilog.com. UART with IrDA Endec The Z8 Encore! 8K/4K contains a fully-functional, high-performance UART with Infrared Encoder/Decoder (ENDEC), component U6. The Infrared Endec is integrated with an on-chip UART allowing easy com- Z8 Encore! 8K/4K Evaluation Board UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual 9 munication between the Z8 Encore! 8K/4K and IrDA transceivers. Infrared communication provides secure, reliable, low-cost, point-to-point communication between PCs, PDAs, cell phones, printers and other infrared enabled devices. Crystal Oscillator The evaluation board ships with an 18.432MHz Crystal Oscillator (Y1). If you want to change the change the Crystal Oscillator you are required to change the Clock Frequency in for ZDSII. The frequency settings can be found at Project > Settings > Debugger > ZDB: Configure ZDB Driver: Clock Frequency. See the Z8Encore! Product Speciification for supported frequencies. Power and Communication Interfaces Table 1 provides jumper information concerning the shunt status, functions, devices and defaults affected of jumpers JP3 and JP4. Table 1. Jumpers JP3 and JP4 Jumper Status JP3** OUT* JP3 Device Affected Status Default RS-232 interface Enabled X IN RS-232 interface Disabled JP4 OUT* IrDA interface Enabled JP4 IN IrDA interface Disabled X Note: * These jumpers must not be OUT at the same time Note: ** If the module is plugged onto an eZ80 Evaluation platform or eZ80 demonstration board the local RS-232 can be disabled by connecting header JP2 pin 50 to the corresponding GND on the mating connector Z8 Encore! 8K/4K Evaluation Board UM015004-1105 Z8 Encore!® 8K/4K MCU Evaluation Kit User Manual 10 External Interface Headers JP1 and JP2 The external interface headers, JP1 and JP2 contain no connectors when the board is shipped. The user can insert 0.1" space connectors of choice. Z8 Encore! 8K/4K Evaluation Board UM015004-1105 Z8 Encore!® Evaluation Kit User Manual 11 Schematics This section includes schematics for the the Z8 Encore!® 8K/4K Evaluation Board. Schematics UM015004-1105 Z8 Encore! ® 8K/4K MCU Evaluation Kit User Manual 12 VCC_33V VCC_33V VCC_33V connector 2 GND GND C12 22uF + C13 0.01uF JP2 GND VCC_33V PC4_MOSI D2 PA0_T0IN 1 2 100 RED R9 D3 PA1_T0OUT PC3_SCK PC0_T1IN GND PC1_T1OUT R8 1 R10 SW2 VCC_33V 2 GND 100 GREEN TEST 100K GND R11 D4 PA2 PA3_CTS0 PA4_RXD0 1 PA6_SCL PA7_SDA 2 YELL C4 100 R12 -RESET VCC_33V 100 0.1uF VCC_33V U7 PA6_SCL PA7_SDA -RESET GND XIN XOUT VCC_33V PA0_T0IN PA1_T0OUT PA2 1 2 3 4 5 6 7 8 9 10 20 pin Socket PA6/SCL PA7/SDA RESET GND XIN XOUT VDD PA0/T0IN PA1/T0OUT PA2/DE U8 PC0/T1IN PB0/ANA0 PB1/ANA1 VREF AGND AVDD DBG PA5/TXD0 PA4/RXD0 PA3/CTS0 20 19 18 17 16 15 14 13 12 11 PC0_T1IN PB0_ANA0 PB1_ANA1 VREF AGND VCC_33V DBG PA5_TXD0 PA4_RXD0 PA3_CTS0 PC0_T1IN PA6_SCL PA7_SDA -RESET GND XIN XOUT VCC_33V PC5_MISO PC4_MOSI PC3_SCK PC2_SS PA0_T0IN PA1_T0OUT Z8F0xx1 VCC_33V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 pin Socket PC0/T1IN PA6/SCL PA7/SDA RESET VSS XIN XOUT VDD PC5/MISO PC4/MOSI PC3/SCK PC2/SS PA0/T0IN PA1/T0OUT PB0/ANA0 PB1/ANA1 PB2/ANA2 PB3/ANA3 PB4/ANA4 VREF AVSS AVDD DBG PC1/T1OUT PA5/TXD0 PA4/RXD0 PA3/CTS0 PA2/DE 28 27 26 25 24 23 22 21 20 19 18 17 16 15 PB0_ANA0 PB1_ANA1 PB2_ANA2 PB3_ANA3 PB4_ANA4 VREF AGND VCC_33V DBG PC1_T1OUT PA5_TXD0 PA4_RXD0 PA3_CTS0 PA2 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 GND PC5_MISO PC2_SS PA0_T0IN PA1_T0OUT PA2 GND PA5_TXD0 GND -DIS_IrDA If Module is plugged onto the Dev Platform the local -DIS_232 RS232 interface is disabled by pin 50 of JP2 -DIS_IRDA GND HEADER 30x2/SM connector 1 for reference only JP1 DBG 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 A21 37 A22 39 -CS0 41 -CS2 43 D1 45 D3 47 D5 49 D7 51 -MREQ 53 GND 55 -WR 57 -BUSACK 59 -TRSTN -F91_WE GND A6 A10 GND A8 A13 A15 A18 A19 A2 A11 A4 A5 Z8F0XX2 R3 10K RESET -RESET DBG PA5_TXD0 PA3_CTS0 PA4_RXD0 -RESET SW1 XIN XOUT C10 0.01uF VREF R13 220 Y1 18.432MHz R14 PB0_ANA0 100K C15 18pF 18pF C16 DBG PA5_TXD0 PA3_CTS0 PA4_RXD0 PB1_ANA1 PB2_ANA2 PB3_ANA3 PB4_ANA4 + C17 0.001uF C18 0.001uF C19 0.001uF C20 0.001uF C21 0.001uF AGND C14 22uF C22 0.01uF PB0_ANA0 PB1_ANA1 PB2_ANA2 PB3_ANA3 PB4_ANA4 J2 1 3 5 7 9 2 4 6 8 10 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 VCC_33V VCC_33V A0 A3 VCC_33V A7 A9 A14 A16 GND A1 A12 A20 A17 -DIS_FLASH VCC_33V A23 -CS1 D0 D2 D4 GND D6 -IOREQ -RD -INSTRD -BUSREQ Header 5x2 HEADER 30x2/SM Title Schematic, Z8 Encore! ® 8K/4K MCU Evaluation Board, Page 1 of 2 Appendix UM015004-1105 Z8 Encore! ® 8K/4K MCU Evaluation Kit User Manual 13 VCC_33V J1 PWR JACK 5V VCC RXE110 VCC U10 + C1 C23 0.1uF C3 0.1uF 100/10 U2 3 1 VCC_33V 2 VIN VOUT GND PA5_TXD0 + C8 C9 C5 0.1uF VCC_33V R1 LT1086-3.3/TO220 19 F1 PA5_TXD0 GND 680 2 C1+ 4 C1- VCC 2 3 1 V+ 3 CONSOLE P1 GND C7 0.1uF 5 C2+ 6 C2- 13 T1IN T1OUT 17 12 T2IN T2OUT 8 15 R1OUT R1IN 16 10 R2OUT R2IN 9 V- C6 0.1uF 1 6 2 7 3 8 4 9 5 TXD0 CTS0 RXD0 7 100/10 LED 3.3 OK PA4_RXD0 PA4_RXD0 1 1 20 GND EN GND D1 SHDN MAX3222 NC NC DB9 Female USER 14 11 18 PA3_CTS0 PA3_CTS0 2 0.1uF VCC_33V GND 14 R15 10K U4A 74LVC04/SO 1 JP3 1 2 2 7 -DIS_232 GND DIS RS232 R5 C11 VCC_33V 68 330nF R6 14 R4 10K U4B PA5_TXD0 74LVC04/SO 3 -DIS_IRDA IRDA_SD 4 PA4_RXD0 5 VCC 1 LEDA 2 TXD 4 SD 3 RXD 6 GND 7 JP4 1 2 T U6 2R7 ZHX1810 0 GND DIS IRDA GND TP1 GND R7 10K 1 2 3 4 5 1 2 3 4 5 VCC_33V TP2 P2 VCC_33V GND 1 3 5 DBG INTERFACE 2 4 6 -RESET DBG -RESET DBG Title Encore! F08. Evaluation Module. Schemat Header 3x2 Size B Document Number 96C0897-001 ® Schematic, Z8 Encore! 8K/4K Evaluation Board Page 2 of 2 Appendix UM015004-1105