Download FM65-B5511 / FM65-B8001 User`s Manual

Tyan MicroServer Series
FM65-B5511 / FM65-B8001
4U SERVER – 18 NODES
User’s Manual
Revision History
Refer to the table below for the updates made to this user’s manual.
Revision No.
Draft Date
Note
Copyright
This publication, including all photographs, illustrations, and software, is protected under
international copyright laws, with all rights reserved. Neither this manual, nor any material
contained herein, may be reproduced without written consent of manufacturer.
Copyright 2012 MiTAC International Corporation. All rights reserved. TYAN® is a registered
trademark of MiTAC International Corporation.
Version 1.0a
Disclaimer
Information contained in this document is furnished by MiTAC International Corporation and
has been reviewed for accuracy and reliability prior to printing. MiTAC assumes no liability
whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of
TYAN® products including liability or warranties relating to fitness for a particular purpose or
merchantability. MiTAC retains the right to make changes to produce descriptions and/or
specifications at any time, without notice. In no event will MiTAC be held liable for any direct
or indirect, incidental or consequential damage, loss of use, loss of data or other malady
resulting from errors or inaccuracies of information contained in this document.
Conventions
The following conventions are used in this manual:
!
WARNING:
Indicates a potential for property damage, personal injury or death.
!
CAUTION:
Indicates a potential loss of data or damage to equipment.
NOTE:
NOTE:
Indicates information that is important to know for the proper completion of a procedure,
choice of an option, or completing a task.
ii
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
About the Tyan MicroServer System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Product Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
Catalog Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Necessary Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Safety Information and Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recycling Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Work Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-2
2-2
2-2
2-2
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
System Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
System Rear View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
System Internal View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Compute Blade Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FM65-B5511 Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FM65-B8001 Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compute Blade LED Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6
2-6
2-7
2-8
Mid Plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
Pass-through / CMM Module Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10
Pass-through / CMM LED Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
I/O Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
I/O Port Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Mounting the System into a 4-Post Rack. . . . . . . . . . . . . . . . . . . . . . . . . .2-12
Preparing for the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Inner Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Outer Rail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the System using the 4-Post Rack Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-12
2-12
2-13
2-13
Chassis Management Module . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Acquiring an IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Chassis Management Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Server Health . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GroupBMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3
3-4
3-4
3-5
3-6
3-7
3-7
iii
Compute Blade Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Compute Blade, Power Supply & Fan Module Order Identification . . . . . .4-2
Compute Blade Numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Compute Blade Blanks (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Removing a Compute Blade Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Installing a Compute Blade Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Compute Blade Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Removing a Compute Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Installing a Compute Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
General Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Population Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing a Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing a Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5
4-5
4-5
4-5
Hard Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7
Installing a Hard-Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Removing a Hard Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9
General Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Removing a Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Installing a Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Heat-Sinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-13
General Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Installing a Heat-Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Removing a Heat-Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-15
Removing a Bridge Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing a Bridge Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing a System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing a System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-15
4-15
4-16
4-17
Chassis Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
System Power Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Removing a Power Supply Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Installing a Power Supply Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Fan Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
Removing a Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Installing a Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Opening and Closing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
Opening the Top Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Closing the Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
iv
Pass-through / CMM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Removing Pass-through / CMM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Pass-through / CMM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing an I/O and CMM System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing an Pass-through / CMM System Board . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6
5-6
5-7
5-8
Troubleshooting the MicroServer . . . . . . . . . . . . . . . . . . . . . . . 6-1
Safety First. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Start-up Routine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Checking Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Troubleshooting External Connections . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
System Alert Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Troubleshooting Chassis Components . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
PSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pass-through / CMM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1
6-1
6-1
6-1
Troubleshooting Compute Blade Components . . . . . . . . . . . . . . . . . . . . .6-2
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hard Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2
6-2
6-2
6-2
System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Administrator Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Running System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Testing Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2
6-2
6-2
6-2
6-3
6-3
Parts Listing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Getting Help and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
v
vi
Chapter 1: Overview
About the Tyan MicroServer System
0
Congratulations on the purchase of the Tyan MicroServer, a highly optimized 4U rack mount
system. The Tyan MicroServer is available in two models, the FM65-B5511 featuring the
Intel® Sandy Bridge-DT processor and the FM65-B8001 featuring the AMD® Opteron AM3
processors, designed to support 18 compute blades. Up to 32 GB UDIMM
DDR3-800/1066/1333 memory can be installed per node. Utilizing advanced technology the
Tyan MicroServer system provides scalable 32/64-bit computing, high bandwidth memory
design, and lightning-fast PCI-E bus capabilities. The Tyan MicroServer not only can be
utilized to manage today’s IT environments as well as tomorrow’s.
The Tyan MicroServer uses the latest chassis designs for solid mechanical enclosures and
robust features. The Tyan MicroServer delivers the power and flexibility to meet the needs
enterprise-level requirements.
Features
0
The Tyan MicroServer contains the following features:
Table 1-1. MicroServer Features
Item
Chassis
Description





Industry 4U rack-mountable chassis
Dimension:
 Height: 175.7 mm (7.17 inch)
 Width: 440 mm (17.32 inch)
 Depth: 650 mm (25.6 inch)
(18) Compute Blades(1) Pass Through/CMM module
(8) 8038 System FANs
Power supply
 (2+1) 800W high efficiency (80+ Gold) w/ PFC (AC SKU)
 DC 12V sourced from rack (DC SKU, option)
System board
Tyan B5511GM2N, B8001GM2N
Processors
FM65-B5511
 Support (1) Intel® Sandy-Bridge-DT CPU (Socket H2)
 Quad-core Sandy Bridge-DT w/ TDP 45W
 Dual-core Sandy Bridge-DT w/ TDP 20W
FM65-B8001
 Support (1) AMD® Opteron AM3 socket
 Athlon II X2 Dual-Core CPU (45W)
 Athlon II X3 Tri-Core CPU (45W)
 Athlon II X4 Quad-Core CPU (45W)
Overview
1-1
Table 1-1. MicroServer Features (Continued)
Item
Description
Chipset
FM65-B5511
 Intel® Cougar Point PCH
 AST2150 iBMC
FM65-B8001
 AMD SR5650 + SP5100
 AST2150 iBMC
Memory
FM65-B5511, FM65-B8001
 (4) U-DDR-III w/ECC 1066/1333 VLP UDIMM
Integrated LAN Controllers
(2) Intel® 82574L Gigabit controllers
BIOS




Internal Connector


Internal I/O




Form Factor (Compute
Blade)
AMI BIOS® on 8Mbit Flash ROM
Supports ACPI 2.0
Supports boot from USB device
Power-on mode control for AC power loss recovery
(1) One SATA connector for 2.5” SATA/SATAII hard drive on the
motherboard
(1) One SATA connector for 2.5” SATA/SATAII hard drive on the
Bridge Board
(2) USB ports
(1) VGA port
Switches
 Power
LED
 Power LED
 Hard drive activity LED
 System health/ID LED
W128.88 x H28 x D358.8 mm (5.07 x 1.10 x 14.13 inch)
NOTE:
Supports 9 mm high hard drive.
1-2
Overview
Table 1-1. MicroServer Features (Continued)
Item
Pass-through-M1902F65CMMPT
Description

Gigabit PHY
 (2) BCM 54616s GPHY
 (2) Octal Giga PHY (BCM54980)

CMM subsystem
 (1) ASPEED AST2150
 (1) 8 MB FLASH
Rear I/O
 (1) RJ45 to support remote management from CMM
 (18) RJ45 1000 Base-T port w/ activity LED
 (1) One Power Switch
 (1) Power LED
 (1) System Health LED
Form factor: W108 mm x L358.4 mm (4.25 in x 14.11 inch)


Mid-Plane (M1247F65-BP)




PDB Board
(M1608F65-PDB)





Bridge Board
(M1708F65-BDG)
Overview


System management
 (1) CMM connector for IPMB
 (4) I2C switch for I2C Bus extender
 (4) Power connector (PDB)
Blade connection
 (18) PCI-E x 8 connector
H/W Monitor
 (4) System temperature sensor with SMBUS
Form Factor: W435 mm x L165 mm (17.13 in x 6.50 inch)
Power Rating SPEC
 1600W Power output rating (2+1 Redundant PSU)
PSU Power Input
 (3) System PSU comply connectors
 12DC power input from Chassis Power delivery system
 12V and 12Vsb power input
Blade System DC power input
 DC power Connector
 12V DC power input from chassis delivery system
Power output
 (4) Power connector for Blade power
 12V DC power
Form Factor: W176.5 mm x L150 mm (6.95 in x 5.91 inch)
One(1) SATA connector for 2.5'' SATA/SATAII hard drive
Form factor: W118.88 mm x L96.8 mm (4.68 in x 3.81 inch)
1-3
Table 1-1. MicroServer Features (Continued)
Item
CMM
Description


Dedicated LAN port for chassis management
Remote management & monitoring
 System Blades


Blade
Present status
Blade
Power On/Power Off
Blade
Power Stagger Start-up
Blade
Reset
Blade
Graceful Shutdown
Blade
identify (LED on/off)
Power Supplies
Power
Present status
Power
Status (on or off)
Cooling fans
FAN
speed control & monitor
FAN

failed alert
Networking switches (option)
Reset
Ethernet Switch
Gigabit





1-4
Switch Management UI Links
H/W Healthy Monitor (Blade/Chassis/PSU module/FAN
module):
 System Healthy monitor (Temperature sensors, power status
and FAN speed)
 System Event Log
Advance Control
 Power Fail alert.
 Power consumption Monitor (AC-in/DC-in/DC-out)
IPMI 2.0 MANAGEMENT Through LAN or I2C
E-MAIL report
Chassis Graceful Shutdown
Overview
Table 1-1. MicroServer Features (Continued)
Item
Blade BMC
Description

Remote management & monitoring
 System Blades
Blade
Power On/Power Off
Blade
Reset
Blade
Graceful Shutdown
Blade







Operating Environment
Overview
identify (LED on/off)
H/W Healthy Monitor:
 System Healthy monitor (Temperature sensors, and voltages)
 System Event Log
IPMI 2.0 MANAGEMENT Through LAN or I2C
iKVM
Serial Over LAN (SOL)
Virtual Media Over LAN
Email report
Chassis Graceful Shutdown
Operating Temperature
 10°C to 35°C
Non-Operating Temperature
 FM65-B5511
 -40°C to 70°C
 FM65-B8001
 -40°C to 70°C
Operating Humidity
 FM65-B5511
 10% to 80%
 FM65-B8001
 15% to 80% (non-condensing) at 40°C
Non-Operating Humidity
 FM65-B5511
 5% to 95%
 FM65-B8001
 8% to 80% (non-condensing) at 40°C
1-5
Product Models
0
The system board within the Tyan MicroServer blades contain different processors and
chipsets, which are defined by the following models:
FM65-B5511-Intel
based platform
FM65-B8001-AMD
based platform
Catalog Parts List
0
Contents
0
FM65 Chassis Kit
(1)
4U Chassis
(1)
Pass-through / CMM module
(8)
Fan Modules
(3)
Power Supply Modules
(1)
Power Distribution Board (M1608F65-PDB)
(1)
Mid Plane Board (M1247F65-BP)
Compute Blade Single Kit
(6)
Compute Blade Blanks
(6)
Tyan System Boards configured for the FM65-B5511 and FM65-B8001 models
(6)
Bridge Boards (M1708F65-BDG)
(6)
Heat-sinks
(1)
HDD Screw Kit
Accessories
Rail
0
Mounting Kit
Accessory Kit
1-6
(3)
US Power Cord
(3)
EU Power Cord
(1)
USB Cable
(1)
Rail Screw
Overview
Chapter 2: About Your System
Necessary Information
0
Safety Information and Precautions
0
Before installing and using Tyan MicroServer, review the following precautions:
Read
all instructions carefully.
Do
not place the unit on an unstable surface, cart, or stand.
Do
not block the slots and opening on the unit, which are provided for ventilation.
Only
use the power source indicated on the marking label.
The
unit uses a three-wire ground cable, which is equipped with a third pin to ground
the unit and prevent electric shock.
Do
not place anything on the power cord. Place the power cord where it will not cause
an accident.
Follow
all warnings and cautions in this manual and on the unit case.
Do
not push objects in the ventilation slots as they may touch high voltage components
and result in shock and damage to the components.
When
replacing parts, ensure that parts specified by the manufacturer are used.
When
service or repairs have been done, perform routine safety checks to verify that
the system is operating correctly.
Avoid
using the system near water, in direct sunlight, or near a heating device.
Cover
the unit when not in use.
Components and circuit boards can be damaged by static electricity discharge. Follow the
guidelines below to avoid damage to the system or bodily injury.
Proper grounding is required before removing the top cover of the system. Disconnect the
power cable from the power supply and then touch a grounded object to release static charge.
A grounded wrist strap is recommended during any maintenance or troubleshooting to the
system. To ensure proper handling of the components, refer to the following guidelines:
Avoid
touching system board components, IC chips, connectors memory modules and
leads.
The
system board is pre-installed in the system. When removing the system board,
always place it on a grounded anti-static surface until it is ready to be reinstalled.
Hold
electronic circuit boards by the edges only. Do not touch the components on the
board unless it is necessary to do so. Do not flex, bend or stress circuit boards.
Leave all
components inside the static-proof packaging that they ship with until they are
ready for installation.
After
replacing components and devices, make sure all screws, springs, or other small
parts are in place and are not left loose inside the case. Metallic parts or metal flakes
can cause electrical shorts.
About Your System
2-1
Recycling Information
0
A lithium battery is included with the Tyan MicroServer. Do not puncture or dispose of battery
in fire. There is a danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by manufacturer. Disposal and recycling of used
batteries, parts and components should be done in accordance with local regulations.
General Information
0
The illustrations are representative of the latest system revision available at the time of
publishing. The system you receive may not look exactly like the illustrations described later.
Work Area
0
All maintenance and/or troubleshooting of the Tyan MicroServer should be conducted in a
stable, clean working environment. Use containers to store small components separated,
which prevents them from becoming lost or mixing with other components. The use of proper
tools and adequate lighting is recommended.
Recommended Equipment
0
The following tools are suggested to perform maintenance on the Tyan MicroServer:
Phillips
screwdriver
Wrist-grounding
2-2
strap or conductive mat/anti-static pad
About Your System
System Overview
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or services that are not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
The Tyan MicroServer contains components that can be removed and replaced. The following
image indicates the location of the components that can be removed, which are further
described in detail in Chapters 5 and 6 of this user’s manual.
System Fan
Modules
Power Supply
Modules
Pass-through / CMM
Module
Compute
Blades
Figure 2-1.
About Your System
Tyan MicroServer Overview
2-3
System Front View
0
2
1
Figure 2-2.
Table 2-1.
Front View
System Front View Modules
ID
Description
1
Compute Blade (x18)
2
Pass-through / CMM Module
System Rear View
0
2
1
Figure 2-3.
Table 2-2.
System Rear View Modules
ID
2-4
Rear View
Description
1
Fan Modules (x8)
2
Power Supply Modules (2+1)
About Your System
System Internal View
0
2
1
Figure 2-4.
Table 2-3.
ID
About Your System
Internal View
System Internal View Modules
Description
1
Mid Plane (M1247F65-BP):
18x PCI-e x 8 connector)
2
Power Distribution Board (PDB): M1608F65-PDB
2-5
Compute Blade Overview
0
Features
0
FM65-B5511 Blade
(1)
Intel® Sandy Bridge DT, Socket H2, Intel E3 series CPU
Intel®
Cougar Point PCH
FM65-B8001 Blade
(1)
AMD® Opteron AM3 socket
AMD
SR5650 + SP5100
Common Features
Compact
compute blade: 118.88 mm X 263.52 mm(4.68 in x 10.37 inch)
AST2150
iBMC
(4)
DDR3 VLP UDIMM slots (up to 32 GB)
(2)
Internal 2.5” hard drive bays (with connected bridge board)
(2)
Intel® 82574L Gigabit controllers
FM65-B5511 Blade
0
Front View
0
Blade Release
Latch
USB Ports
Handle
VGA Port
Figure 2-5.
2-6
ID/Status
LED
Hard Drive
Activity LED
Power Button/
System Power LED
FM65-B5511 Blade Front View
About Your System
Internal View
0
Hard Drive
Memory
Module
Hard Drive
Processor
Figure 2-6.
FM65-B5511 Blade Internal View
FM65-B8001 Blade
0
Front View
0
Blade Release
Latch
USB Ports
Handle
VGA Port
Figure 2-7.
About Your System
ID/Status
LED
Hard Drive
Activity LED
Power Button/
System Power LED
FM65-B8001 Blade Front View
2-7
Internal View
0
Hard Drive
Memory
Module
Hard Drive
Processor
Figure 2-8.
FM65-B8001 Blade Internal View
Compute Blade LED Behavior
0
The following information provides LED behavior for both compute blade models.
Table 2-4.
Compute Blade LED Behavior
Field
HDD Activity
Color
Blinking Green
Access
Off
System normal
ID
Solid blue
Active
System Status
Solid Red
Alert
Off
Normal
ID/System Status Blinking blue/red
System Power
2-8
Behavior
ID located/System Alert
Solid Green
Power on
Off
Power off
About Your System
Mid Plane
0
1
Figure 2-9.
2
Mid Plane Front View
Table 2-5.
Mid Plane Front View
ID
Description
1
PCI-E x8 connectors (x18)
2
PCI-E x16 connectors (x2)
1
3
2
Figure 2-10. Mid Plane Rear View
Table 2-6.
ID
About Your System
Mid Plane Rear View
Description
1
2 x 6 PIN Power connector (x4)
2
2 x 5 PIN I2C connector
3
2 x 15 PIN FAN connector
2-9
Pass-through / CMM Module Overview
Gigabit LAN Ports 1 to 18
Pass-through / CMM
Release Latch
Figure 2-11.
Dedicated
Remote
Management
Port
Pass-through / CMM Module Front View
management & monitoring
Blades
Blade
Present status
Blade
Power On/Power Off
Blade
Power Stagger Start-up
Blade
Reset
Blade
Graceful Shutdown
Blade
Identify (LED on/off)
Power
Supplies
Power
Present status
Power
Status (on or off)
Cooling
fans
FAN
Speed Control & Monitor
FAN
failed alert
Networking
Reset
switches
Ethernet Switch
Gigabit
Switch Management UI Links
Healthy Monitor (Blade/Chassis/PSU module/FAN module):
System
Healthy Monitor (Temperature sensors, power status and FAN speed)
System
Event Log
Advance
2-10
CMM
Status
ID/Warning
LED
LED
LAN port for chassis management
System
H/W
0
Control
Power
Fail alert.
Power
consumption Monitor (AC-in/DC-in/DC-out)
About Your System
PMI
2.0 MANAGEMENT Through LAN or I2C
E-MAIL
report
Chassis
Graceful Shutdown
Pass-through / CMM LED Behavior
0
The following information provides LED behavior for both compute blade models.
Table 2-7.
Pass-through / CMM LED Behavior
Field
Status
CMM Status
LED
CMM ready
Green
Solid on
GPIOA4/P
HYLINK
CMM fail
Red
Solid on
GPIOA5/P
HYPD#
ID located
Blue
Solid on
GPIOB5/V
BCK
Warning LED System fan
fail
Red
Solid on
VPAVSYN
C/VSYNC/
GPIOH5
Fan fail
Abnormal fan speed
Warning LED PSU fail
Red
VPAVSYN
C/VSYNC/
GPIOH5
OVP, OCP, OTP, AC
lose
PSU fan fail
PSU asserted, AC
on, no Vsb
Must
VPAVSYN
C/VSYNC/
GPIOH5
Single PSU failure
triggers warning
display
Must
ID LED
Warning LED 2+1 PSU
redundancy
fail
Color
Red
Indication
Solid on
Solid on
Address
Remark
Event Log
Either Red or Green
LED is on, not both.
Must
Must
I/O Connectivity
0
I/O Port Mapping
0
Compute Blade I/O Ports
(2)
USB ports
(1)
VGA port
0
Pass-through / CMM Module Ports
(1)
RJ45 to support remote management from CMM
(1)
2x8 ports RJ45 1000 Base-T port w/ activity LED
(1)
2x1 ports RJ45 1000 Base-T port w/ activity LED
About Your System
0
2-11
Mounting the System into a 4-Post Rack
0
After installing the necessary components, the Tyan MicroServer can be mounted in a 4-post
rack using the optional rail kit.
The rail kit includes the following items:
(2)
Rail kit assemblies
(1)
Set of screws
Preparing for the Installation
0
Review
all the tasks required to install and configure the system.
Review
the electrical requirements and power supply input voltage information.
Examine
the system’s shipping kit contents and assemble the required tools for
installation.
Review
ESD requirements and take safety precautions.
Before
installing the system into a rack, install any optional components into the
system.
Stabilize
the rack before installing the system, if necessary.
Installing the Inner Rail
!
0
WARNING:
Use caution when removing the inner rail from the rail kit assembly. The rails can
slide out and cause personal injury or damage to the TYAN MicroServer.
1. Remove the inner rail from the rail kit assembly.
2. Align and insert the holes on the inner rail into the pins on the side of the chassis.
(Figure 2-12)
3. Slide the inner rail until the latch key on the rail locks and is secure to the chassis.
4. Repeat steps 1 through 3 for the remaining side.
Latch Key
Inner Rail
Figure 2-12.
2-12
Installing the Inner Rail
About Your System
Installing the Outer Rail
!
0
WARNING:
Use caution when installing the outer rail. The middle rail, which is attached to the
outer rail, can slide out and cause personal injury or damage to the system.
1. Align and place the front mounting bracket of the outer rail on the front cabinet column of
the rack. (Figure 2-13)
2. Extend the length of the outer rail until the rail reaches the rear cabinet column of the rack
3. Align and place the rear mounting bracket on the rear cabinet column of the rack.
NOTE:
NOTE:
4. Secure the outer rail to the rack with the screws and washers to the front and rear of the
rack.
NOTE:
NOTE:
The outer rails contain the words “FRONT” and “REAR”. The “FRONT” of the outer rail
must be placed towards the front of the rack and “REAR” must be placed towards the
rear.
!
CAUTION:
Both outer rails must be aligned evenly or the chassis cannot be installed to the
rack. Use a ruler to ensure that both rails are evenly aligned in a 180 degree
angle.
5. Repeat steps1 through4 for the opposite side.
Front Cabinet
Column
Outer Rail
Figure 2-13.
Rear Cabinet
Column
Installing the Outer Rail
Installing the System using the 4-Post Rack Kit
!
0
WARNING:
Due to the weight of the system, two people are required to lift and mount the
system into a rack enclosure when following the procedure.
About Your System
2-13
Prerequisite:
Remove all compute blades from the chassis. Refer to Removing a Compute
Blade.
Remove the Pass-through / CMM module. Refer to Removing Pass-through /
CMM Module.
Remove the power supply modules. Refer to Removing a Power Supply
Module.
1. Lift the chassis until it is leveled with the outer rails on the rack. (Figure 2-14)
2. Align the left and right side of the inner rail on the chassis with the outer rails on the rack.
3. Insert the rear side of the chassis into the rack until the inner rails and outer rails lock into
place.
4. Secure the chassis to the rack by installing (2) screws from the mounting flanges to the
rail.
5. Install the compute blades into the chassis. Refer to Installing a Compute Blade.
!
CAUTION:
Compute blades should be installed in the order shown in Compute Blade, Power
Supply & Fan Module Order Identification.
6. Install the Pass-through / CMM module into the chassis. Refer to Installing Pass-through /
CMM Module.
7. Install the power supply modules. Refer to Installing a Power Supply Module.
Outer Rail
Inner Rail
Figure 2-14.
2-14
Installing the System to a 4-Post Rack
About Your System
Chapter 3: Chassis Management Module
This chapter provides information about the chassis management console. To login remotely
into the chassis management module (CMM) and access the console, you must first acquire
the CMM’s IP address.
Acquiring an IP Address
0
This section provides information in order to acquire an IP address for use in setting up and
configuring the Chassis Management Module (CMM).
Before you start, make sure all compute blades and the CMM are connected to the network
through a DHCP server (recommended).
1. Power up the MicroServer.
All MicroServer blades are powered on by the system through the BMC.
2. Connect a monitor and keyboard to an active compute blade. See “FM65-B5511 Blade” on
page 6 or “FM65-B8001 Blade” on page 7 for port locations.
3. In the POST screen, navigate to Server Management and look for the compute blade
BMC IP address
NOTE:
NOTE:
Note the BMC IP address is assigned by the DHCP server.
4. Connect a remote computer to the same network used by the MicroServer.
5. In the remote computer, open a browser and in the address bar type the BMC IP (See step
3).
6. In the login screen, type in the following username and password for both CMM and BMC.
username: root
password: superuser
Figure 3-1.
NOTE:
Login Menu
NOTE:
Passwords are case sensitive.
Chassis Management Module
3-1
7. Select Group BMC=> Node BMC.
CMM IP displays in the Select GroupBmc drop down list.
NOTE:
NOTE:
Note that CMM IP must be in the same subnet as the MicroServer Blade BMC. An IP
address result such as 127.0.0.1 is not valid and typically indicates there is a
configuration error between the CMM BMC and compute blade node. It may be
necessary to wait for a short period to allow for network settings to take place before
beginning troubleshooting steps.
3-2
Chassis Management Module
Chassis Management Console
0
Overview
0
This section displays the initial screen information.
Figure 3-2.
Management Console Menu
Table 3-1. Management Console
Item
Description
Options
Displays available submenus.
Refresh
Refresh the current menu.
Logout
Select to logout.
Chassis Management Module
3-3
System Information
0
The System Information menu provides general system information about the MicroServer
system.
Figure 3-3.
System Information Menu
Table 3-2. System Information
Item
Description
System Information
Displays firmware and AuxFirmware revision as well as
build time information
List FRU
Displays available field replacement units (FRU) in the
MicroServer. Further information for each FRU item is
available by clicking on the FRU item.
Server Health
0
The Server Health menu provides information about the MicroServer system’s sensor
readings and event logs.
Figure 3-4.
3-4
Server Health Console Menu
Chassis Management Module
Table 3-3. Server Health
Item
Description
Sensor Readings
Event Log
Select to display readings with or without thresholds from
various MicroServer sensors.
Select to view the written event logs by Sensor-Specific,
BIOS Generated, or System Management Software events.
Configuration
0
The Configuration menu provides information for alert, user and network settings to configure
and setup the MicroServer system.
Figure 3-5.
Configurtation Console Menu
Table 3-4. Configuration
Item
Alerts
Mouse Mode
Network Settings
SMTP
User List
SDR
Chassis Management Module
Description
Select to configure or test an existing alert.
Select the type of mouse mode, absolute (Default) or
relative.
Select to view and configure the network settings (DHCP or
static).
Select to configure alerts, users and network SMTP
settings
Select to add, modify or delete the current configured users
list.
Select to modify, enable or disable sensor thresholds.
3-5
Table 3-4. Configuration (Continued)
Item
Description
Date Time/NTP
Settings
Select to manually set the date and time settings or
synchronize with a specified NTP server.
SSL Certificate
Select to upload an SSL certificate.
Remote Control
0
The Remote Control menu provides information about the remote management and power
status of the MicroServer system.
Figure 3-6.
Remote Control Console Menu
Table 3-5. Remote Control
Item
CMM Controls
NodeBMC Controls
3-6
Description
Select to set the power status of the microserver.
Select to manage nodes.
Chassis Management Module
Maintenance
0
The Maintenance menu provides information regarding the maintenance tasks available for
the MicroServer system.
Figure 3-7.
Maintenance Console Menu
Table 3-6. Maintenance
Item
Description
Firmware Update
Select to enter the system’s Update Mode. The Update
Mode allows for the updating the firmware. A system reset
will follow after the Update Mode.
GroupBMC
0
The GroupBMC menu provides information about BMC groups, such as grouped BMC, Node
or User lists.
Figure 3-8.
Chassis Management Module
GroupBMC Console Menu
3-7
Table 3-7. GroupBMC
Item
GroupBMC List
Add, delete or scan GroupBMC lists.
NodeBMC List
Select existing GroupBMC lists to manage respective
nodes.
Group Login User
3-8
Description
Select to designate user groups for grouped control
functionality.
Chassis Management Module
Chapter 4: Compute Blade Components
Introduction
0
This chapter explains how to replace components relating to the compute blade module,
including the blade blank, system memory, hard drive, heat-sink, processor, bridge board and
system board.
Disassembly Flowchart
0
The following flowchart outlines the disassembly procedures.
-
Figure 4-1.
Compute Blade Components
Disassembly Flowchart
4-1
Compute Blade, Power Supply & Fan Module Order
Identification
0
Before installing front components into the chassis, review the compute blade enumeration for
each component.
Compute Blade Numbering
0
16
17
18
13
14
15
10
11
12
7
8
9
4
5
6
1
2
3
Power Supply Numbering
PSU3
PSU2
PSU1
Fan Module Numbering
4-2
1
2
3
4
5
6
7
8
Compute Blade Components
Compute Blade Blanks (Option)
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
!
CAUTION:
For cooling purposes, when a compute blade is removed, it should be
immediately replaced with another compute blade for proper cooling and air
circulation to occur.
Removing a Compute Blade Blank
0
Prerequisite:
Disconnect all cables and peripherals from the compute blade(s).
1. Press and hold the release latch on the compute blade blank. (Figure 4-2)
2. Pull the handle on the compute blade blank to remove it from the chassis.
Release
Latch
Handle
Figure 4-2.
Removing a Compute Blade Blank
Installing a Compute Blade Blank
0
1. Align the compute blade with the chassis bay. (Figure 4-2)
2. Install the compute blade blank into the chassis until the release latch locks and the
compute blade is seated properly with the chassis.
Compute Blade Components
4-3
Compute Blade Modules
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
!
CAUTION:
For cooling purposes, when a compute blade is removed, it should be
immediately replaced with another compute blade for proper cooling and air
circulation to occur.
Removing a Compute Blade
0
Prerequisite:
Disconnect all cables and peripherals from the compute blade(s).
1. Press and hold the release latch on the compute blade. (Figure 4-3)
2. Pull the handle on the compute blade to remove it from the chassis.
Release
Latch
Handle
Figure 4-3.
Removing a Compute Blade
Installing a Compute Blade
0
1. Remove the new compute blade module from the packaging.
2. Align the new compute blade module to the chassis bay. (Figure 4-3)
3. Install the compute blade into the chassis until the release latch locks and the compute
blade is seated properly with the chassis.
4-4
Compute Blade Components
System Memory
0
General Guidelines
0
The system board contains four (4) memory slots. Make sure the memory modules are
properly installed and secured before use.
Population Rules
0
MEMORY POPULATION TABLE REQUIRED HERE.
Installing a Memory Module
!
0
WARNING:
Use caution when removing a memory module. The memory module can remain
hot even after the system is powered down.
1. Push the memory slot locking latches outwards. (Figure 4-4)
2. Align the notch on the memory module with the socket guide.
3. Install the memory module into the desired socket.
4. Press down the memory module until the locking latches secure the memory module.
5. Install the compute blade into the chassis. See Installing a Compute Blade.
Memory Module
Notch
Locking Latch
Socket Guide
Socket
Figure 4-4. Installing a Memory Module
Removing a Memory Module
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
Compute Blade Components
4-5
!
WARNING:
Use caution when removing a memory module. The memory module can remain
hot even after the system is powered down.
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to Removing a Compute Blade
(Figure 4-4).
1. Push the memory slot locking latch outwards.
2. Remove the memory module from the socket.
4-6
Compute Blade Components
Hard Drives
0
Installing a Hard-Drive
0
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to page 4-3, Removing a Compute Blade.
1. Remove hard-disk drive bracket from the blade.
2. Align and place the hard drive bracket with the hard drive. (Figure 4-5)
3. Secure the hard drive to the hard drive bracket with four (4) screws.
Figure 4-5.
Installing a Hard Drive Bracket
4. Position and align the bracket flange with the compute blade. (Figure 4-6)
5. Place the hard drive assembly on the compute blade.
Hard Drive
Bracket
Bracket Flange
Figure 4-6.
Installing a Hard Drive Module
6. Install and secure the hard drive assembly with two (2) screws.
7. Install the compute blade into the chassis. Refer to page 4-3, Installing a Compute Blade.
Compute Blade Components
4-7
Removing a Hard Drive
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to Removing a Compute Blade.
1. Remove two (2) screws from the hard drive bracket. (Figure 4-7)
2. Slide and disconnect the hard drive bracket until the hard drive is disconnected from the
connector.
3. Lift and remove the hard drive bracket.
Hard Drive
Bracket
Bracket Flange
Figure 4-7.
Removing a Hard Drive Module
4. Remove four (4) screws from the hard drive bracket. (Figure 4-8)
5. Remove the hard drive bracket from the hard drive module.
Figure 4-8.
4-8
Removing a Hard Drive Bracket
Compute Blade Components
Processors
0
General Guidelines
!
0
CAUTION:
To avoid damage to the system board:
!
Do
not touch the processor socket contacts.
Do
not lower the processor into the socket at an angle.
CAUTION:
To avoid damage to the processor:
Handle
Do
!
the processor ONLY by the edges.
not touch the contacts on the bottom of the processor.
CAUTION:
The heat-sink thermal media is not reusable. It must be replaced after removing a
heat-sink or prior to installing a new processor.
Removing a Processor
0
FM65-B5511 Processor
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
!
WARNING:
There is strong pressure securing the processor locking latch to the socket. Use
caution when releasing the locking lever to prevent damage or injury.
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to Removing a Compute Blade.
Remove the heat-sink. Refer to Removing a Heat-Sink.
1. Release the locking lever from the socket cover tab. (Figure 4-9)
2. Rotate the locking lever on the processor socket from the locked position until the socket
cover is fully open.
!
CAUTION:
Make sure that the locking lever is in the fully open position before installing or
removing a processor. Failure to do so may result in permanent damage to the
system board or the processor.
Compute Blade Components
4-9
3. Remove the processor from the socket.
Processor
Connector 1
Indicator
Locking Lever
Connector 1
Indicator
Socket Corner Tab
Processor
Socket
Top Plate
Figure 4-9. Releasing the Processor Locking Lever
FM65-B8001 Processor
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
!
WARNING:
There is strong pressure securing the CPU locking latch to the socket. Use
caution when releasing the locking lever because it can spring up.
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to Removing a Compute Blade.
Remove the heat-sink. Refer to Removing a Heat-Sink.
1. Release the locking lever from the socket tab. (Figure 4-10)
2. Pull the locking lever on the processor socket from the locked position until it is fully open.
!
CAUTION:
Make sure that the locking lever is in the fully open position before installing or
removing a processor. Failure to do so may result in permanent damage to the
system board or the processor.
4-10
Compute Blade Components
3. Remove the processor from the socket.
Processor
Locking Lever
Connector 1
Indicator
Socket Tab
Connector 1
Indicator
Figure 4-10.
Processor
Socket
Releasing the Processor Locking Lever
Installing a Processor
0
FM65-B5511 Processor
!
0
CAUTION:
If the CPU is positioned in the socket incorrectly, the CPU or system board can
become damaged. The use of force is not required to install the CPU into the
socket.
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to Removing a Compute Blade.
Remove the heat-sink. Refer to Removing a Heat-Sink.
1. Rotate the locking lever on the processor socket from the locked position until it is fully
open.
!
CAUTION:
Make sure that the locking lever is in the fully open position before installing or
removing a processor. Failure to do so may result in permanent damage to the
system board or the processor.
2. Remove the socket cover from the socket.
3. Unpack the new processor and remove any protective material.
4. Align the processor over the socket and make sure the connector 1 indicators on the
processor and the socket are aligned (Figure 4-9).
5. Gently place the processor in the socket.
6. Latch the lever under the top plate’s corner tab, being cautious not to damage the system
board with the tip of the lever.
Compute Blade Components
4-11
7. Secure the locking lever to the socket corner tab.
8. Apply a small amount of thermal grease/thermal pad on the processor.
NOTE:
NOTE:
Always replace the thermal grease/pad before installing a processor. See the
manufacturer’s guidelines for your type of thermal grease/pad.
9. Install the heat-sink. See Installing a Heat-Sink.
10. Install the compute blade into the chassis. See Installing a Compute Blade.
FM65-B8001 Processor
!
0
CAUTION:
If the CPU is positioned in the socket incorrectly, the CPU or system board can
become damaged. The use of force is not required to install the CPU into the
socket.
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to Removing a Compute Blade.
Remove the heat-sink. Refer to Removing a Heat-Sink.
1. Pull the locking lever on the processor socket from the locked position until it is fully open.
!
CAUTION:
Make sure that the locking lever is in the fully open position before installing or
removing a processor. Failure to do so may result in permanent damage to the
system board or the processor.
2. Remove the socket cover from the socket.
3. Unpack the new processor and remove any protective material.
4. Align the processor over the socket and make sure the processor connector 1 indicator is
aligned with the socket connector 1 indicator. (Figure 4-10)
5. Gently place the processor in the socket.
6. Latch the lever under the socket tab, being cautious not to damage the system board with
the tip of the lever.
7. Secure the locking lever to the socket tab to lock the processor socket.
8. Apply a small amount of thermal grease/thermal pad on the processor.
NOTE:
NOTE:
Always replace the thermal grease/pad before installing a processor. See the
manufacturer’s guidelines for your type of thermal grease/pad.
9. Install the heat-sink. See Installing a Heat-Sink.
10. Install the compute blade into the chassis. See Installing a Compute Blade.
4-12
Compute Blade Components
Heat-Sinks
0
General Guidelines
!
0
CAUTION:
The heat-sink thermal grease/pad is not reusable. It must be replaced after
removing a heat-sink or prior to installing a new processor.
Installing a Heat-Sink
0
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to Removing a Compute Blade.
!
WARNING:
Use caution when removing the heat-sink. The heat-sink can remain hot even
after the system has powered down.
1. Unpack the new heat-sink and remove any protective material.
2. Align the heat-sink over the system board and retaining screw holes. (Figure 4-11)
3. Tighten the captive screws on the heat-sink in a diagonally opposite pattern.
Heat-Sink
Figure 4-11. Installing the Heat-Sink
4. Install the compute blade into the chassis. See Installing a Compute Blade.
Removing a Heat-Sink
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
Compute Blade Components
4-13
!
WARNING:
Use caution when removing the heat-sink. The heat-sink can remain hot even
after the system has powered down.
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to Removing a Compute Blade.
1. Loosen four (4) captive screws on the heat-sink. (Figure 4-12)
2. Lift and remove the heat-sink from the system board.
Heat-Sink
Figure 4-12.
4-14
Removing the Heat-Sink
Compute Blade Components
System Board
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
Removing a Bridge Board
0
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to Removing a Compute Blade.
Remove the hard drive. Refer to Removing a Hard Drive.
1. Remove four (4) screws from the bridge board. (Figure 4-13)
2. Slide and disconnect the bridge board from the system board.
3. Lift and remove the bridge board from the compute blade.
Bridge
Board
Connector
System
Board
Figure 4-13.
Removing the Bridge Board
Installing a Bridge Board
0
1. Lower the bridge board onto the compute blade. (Figure 4-13)
2. Slide and connect the bridge board connector to the system board.
3. Install and secure the bridge board with the four (4) screws.
4. Install the compute blade into the chassis. See Installing a Compute Blade.
Compute Blade Components
4-15
Removing a System Board
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the compute blade(s).
Remove the compute blade. Refer to Removing a Compute Blade.
Remove the heat-sink. Refer to Removing a Heat-Sink.
Remove the bridge board. Refer to Removing a Bridge Board.
1. Remove the screws from the system board. (Figure 4-14)
B8001 System x 4 screws
B5511 System x 5 screws
2. Lift the rear of the system board, pivoting it at the front.
3. Pull the system board at the pivot point away from the blade housing.
System Board
USB Slots
Power Button/
System Power LED Slot
Figure 4-14.
4-16
Removing the B8001 System Board
Compute Blade Components
System Board
USB Slots
Power Button/
System Power LED Slot
Figure 4-15.
Removing the B5511 System Board
Installing a System Board
0
1. Align front of the system board, DIMM slots positioned in the front, with the front of the
blade housing.
2. Slide the front of the system board into the housing.
3. Lower the system board into the housing making sure the screw holes on the system
board align with the screw nuts on the board housing.
4. Secure the system board to the blade housing with the screws (Figure 4-14):
B8001 System x 4 screws
B5511 System x 5 screws
5. Install the compute blade into the chassis. See Installing a Compute Blade.
Compute Blade Components
4-17
4-18
Compute Blade Components
Chapter 5: Chassis Components
Introduction
0
This chapter explains how to replace components relating to the chassis components,
including the power supply module, fan module, top cover and Pass-through / CMM module.
Disassembly Flowchart
0
The following flowchart outlines the disassembly procedures.
Figure 5-1.
Chassis Components
Disassembly Flowchart
5-1
Power Supply Modules
0
System Power Guidelines
0
The following table provides specifications about the power supply module.
Table 5-1.
Power System Module Specifications
Information
Description
Vendor
Delta
Model
DPS-800NB B
Type
Redundant PSU
Input Range


AC 100~127Vac / 9.2A / 50-60Hz
AC 200~240Vac / 4.4A / 50-60Hz
Output
+12V / 65A, +12VSB/2A, 800W Max.
Dimensions
(L) 196 mm x (W) 73.5 mm x (H) 40 mm
(7.72 x 2.89 x 1.57 inch)
The following table provides information about the LED lights on the power supply module.
Table 5-2.
LED Status
Bicolor
Power Supply Condition
5-2
Green LED
Amber LED
No AC power to all power supplies
OFF
OFF
Power supply critical event causing a
shutdown; failure, OCP, OVP, Fan Fail
OFF
AMBER
Power supply warning events where the power
supply continues to operate; high temp, high
power, high current, slow fan
OFF
1Hz
Blink AMBER
AC present / Only 12VSB on (PS off) or PS in
Smart Redundant state
1Hz
Blink GREEN
OFF
Output ON and OK
ON
OFF
AC cord unplugged
0.5Hz
Blink GREEN
OFF
Chassis Components
Removing a Power Supply Module
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
!
CAUTION:
Make sure that the power cable is disconnected from the power supply module
(PSU) before attempting to remove the PSU.
1. Disconnect the power cable from the power supply module socket. (Figure 5-2)
2. Press and hold the release latch on the power supply module.
3. Pull the handle on the power supply module to remove it from the chassis.
Power Supply
Socket
Module
Handle
handle
Release
Latch
Figure 5-2.
Removing a Power Supply Module
Installing a Power Supply Module
0
1. Install the power supply module into the chassis until the release latch locks and the
power supply module is seated properly with the chassis. (Figure 5-2)
2. Connect the power cable into the power supply module socket.
Chassis Components
5-3
Fan Modules
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
Prerequisite:
Power down the system.
Removing a Fan Module
0
1. Press and hold the release latch on the fan module. (Figure 5-3)
2. Pull the handle on the fan module to remove it from the chassis.
Handle
Release
Latch
Figure 5-3. Removing a Fan Module
Installing a Fan Module
0
1. Align the fan module with the chassis. (Figure 5-3)
2. Install the fan module and push until the release latch locks and the fan module is seated
properly with the chassis.
5-4
Chassis Components
Opening and Closing the System
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
!
CAUTION:
The top cover must be installed to maintain proper system cooling.
Prerequisite:
Power down the system.
Opening the Top Cover
0
1. Remove three (3) screws from the top cover. (Figure 5-4)
2. Slide the top cover until clear from the chassis.
3. Lift and remove the top cover.
Top
Cover
Figure 5-4.
Opening the Top Cover
Closing the Top Cover
0
1. Place the top cover over the chassis. (Figure 5-4)
2. Slide the top cover until the bottom edge of the top cover is under the chassis and the top
cover is secure to the chassis.
3. Install and secure the top cover with the three (3) screws.
Chassis Components
5-5
Pass-through / CMM Module
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
!
CAUTION:
For cooling purposes, when the Pass-through / CMM module removed, it should
be immediately replaced with another Pass-through / CMM module for proper
cooling and air circulation to occur.
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the Pass-through / CMM module.
Removing Pass-through / CMM Module
0
1. Press and hold the release latch on the Pass-through / CMM module. (Figure 5-5)
2. Pull the handle on the Pass-through / CMM module to remove it from the chassis.
Release
Latch
Handle
Figure 5-5.
Removing a Pass-through / CMM Module
Installing Pass-through / CMM Module
0
1. Install the Pass-through / CMM module into the chassis until the release latch locks and
the module is seated properly with the chassis. (Figure 5-5)
5-6
Chassis Components
Removing an I/O and CMM System Board
!
0
CAUTION:
Most repairs to the Tyan MicroServer should only be performed by a professional
service technician. Basic repairs and troubleshooting can be done if authorized in
the product documentation or if directed by telephone or online support from
Tyan. If damage has occurred due to repairs or service that is not approved by
Tyan, the product warranty becomes invalid. Review all safety guidelines that are
provided with the Tyan MicroServer.
!
CAUTION:
For cooling purposes, when the Pass-through / CMM module removed, it should
be immediately replaced with another Pass-through / CMM module for proper
cooling and air circulation to occur.
Prerequisite:
Power down the system.
Disconnect all cables and peripherals from the Pass-through / CMM module.
Remove the Pass-through / CMM module. Refer to Removing Pass-through /
CMM Module.
1. Remove five (5) screws from the Pass-through / CMM system board. (Figure 5-6)
2. Slightly lift the rear of the system board.
3. Pull and remove the system board from the Pass-through / CMM blade.
I/O and CMM
System Board
Gigabit LAN
Port Slots
Pass-through /
Blade
Management
Port Slot
Figure 5-6.
Chassis Components
Removing the Pass-through / CMM Module System Board
5-7
Installing an Pass-through / CMM System Board
1. Holding the Pass-through / CMM system board in a slight angle, align and insert the
system board connectors with the Gigabit LAN port and management port slots on the
front of the Pass-through / CMM blade. (Figure 5-6)
2. Lower the system board onto the Pass-through / CMM blade.
3. Install and secure the system board to the Pass-through / CMM blade with the five (5)
screws.
4. Install the Pass-through / CMM module into the chassis. See Installing Pass-through /
CMM Module.
5-8
Chassis Components
0
Chapter 6: Troubleshooting the MicroServer
Safety First
0
Start-up Routine
0
Checking Equipment
0
Troubleshooting External Connections
0
System Alert Messages
0
Troubleshooting Chassis Components
0
PSM
0
Fans
0
CMC
0
Pass-through / CMM Module
Troubleshooting the MicroServer
0
6-1
Troubleshooting Compute Blade Components
Memory
0
Hard Drives
0
Processors
0
System Board
0
System Diagnostics
0
Administrator Diagnostics
0
System Diagnostics
0
Using System Diagnostics
0
Running System Diagnostics
6-2
0
0
Troubleshooting the MicroServer
Testing Options
0
Error Messages
Troubleshooting the MicroServer
0
6-3
6-4
Troubleshooting the MicroServer
Chapter 7: Parts Listing
This parts listing supports the FM65-B5511 and FM65-B8001 models.
NOTE:
NOTE:
The illustrations in this document may differ from your model.
Parts Listing
7-1
7-2
Parts Listing
Appendix A: Getting Help and Support
Technical Support
0
If a problem arises with the Tyan MicroServer, you should first turn to your dealer for direct
support. The system has most likely been configured or designed by the dealer and they
should have the best idea of what hardware and software your system contains.
If this option is not available, then MiTAC International Corporation can help. Besides
designing innovative and quality products for over a decade, MiTAC has continuously offered
customers service beyond their expectations. Tyan’s website (http://www.tyan.com) provides
easy-to-access resources such as in-depth Linux Online Support sections with downloadable
Linux drivers and comprehensive compatibility reports for chassis, memory and much more.
With all these convenient resources just a few keystrokes away, users can easily find their
latest software and operating system components to keep their systems running as powerful
and productive as possible. MiTAC also ranks high for its commitment to fast and friendly
customer support through email. By offering plenty of options for users, MiTAC serves multiple
market segments with the industry’s most competitive services to support them.
Please feel free to contact us directly for this service at [email protected]
Help Resources:
See
the Tyan’s website for FAQ’s, bulletins, driver updates, and other information:
http://www.tyan.com
Contact
Check
your dealer for help before calling Tyan.
the Tyan user group: alt.comp.periphs.mainboard.Tyan
TYAN® FM65-B5511/FM65-B800 User's Manual V1.0a
Document No.: D2165-100
Getting Help and Support
A-1
A-2
Getting Help and Support
Appendix B: Safety Information
The following section contains important safety information. Read this section thoroughly
before servicing the system.
General Safety
0
The following are guidelines to ensure general safety:
Maintain
When
a clean environment during and after maintenance.
lifting heavy objects:
1. Ensure you are standing on a clean stable surface to prevent slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles to prevent additional
strain on the muscles in your back. Do not attempt to lift any objects that
weigh more than 16 kg (35 lb) or objects that you think are too heavy for you.
Do
not perform any tasks that will create a hazard make the equipment unsafe.
Before
you starting the system, ensure that all personnel are not in a hazardous
position.
Place
removed covers and other parts in a safe place, away from personnel, while
servicing the system.
Do
not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your
clothing to prevent an electrical discharge.
Wear
safety glasses to prevent injury or a hazard to your eyes.
After
service, reinstall all safety shields, guards, labels, and ground wires. Replace any
safety device that is worn or defective.
Reinstall
all covers correctly before returning the system.
Electrical Safety
!
0
CAUTION:
Electrical current from the system or peripherals can be hazardous. To avoid
personal injury or damage to equipment, disconnect the attached power cord(s)
and peripherals before you open the system, unless specifically instructed
otherwise in a stated procedures.
Observe the following guidelines when working on the system.
Know
the location of the room emergency power-off (EPO) switch, disconnecting
switch, or electrical outlet. In the event of an electrical accident, you can operate the
switch or unplug the power cord quickly.
Do
not work alone under hazardous conditions or near equipment that has hazardous
voltages.
Disconnect
all power before:
Performing
Safety Information
a mechanical inspection
B-1
Working
near power supplies
Removing
or installing the system
Before
you start to work on the system, unplug the power cord. If the power cord
cannot be unplugged, power-off the wall box that supplies power to the system and to
lock the wall box in the off position.
Never
assume that power is disconnected from a circuit. Check that the power cord is
disconnected.
Safety Notices
0
Use caution when lifting.
Table 2-1. Safe Lifting Practices
Weight
B-2
Required
≥ 18 kg (39.7 lbs)
two individuals
≥32 kb (70.5 lbs)
three individuals
≥55 kg (121.2 lbs)
four individuals
Safety Information
Appendix C: Glossary
Glossary
G-1
G-2
Glossary
Appendix D: Index
Numerics
4-Post Rack
Installing
Inner Rail, 2-12
Outer Rail, 2-13
System, 2-13
Mounting, 2-12
Preparing, 2-12
C
Chassis Components, 5-1
Disassembly Flowchart, 5-1
Introduction, 5-1
Compute Blade
Components, 4-1
Disassembly Flowchart, 4-1
Enumeration, 4-2
Features, 2-6
FM65-B5511, 2-6
FM65-B8001, 2-7
Introduction, 4-1
Compute Blade Blank, 4-3
Installing, 4-3
Removing, 4-3
Compute Blade Modules, 4-4
Installing, 4-4
Removing, 4-4
F
Fan Modules, 5-4
Installing, 5-4
Removing, 5-4
H
Hard Drives, 4-7
Installing, 4-7
Removing, 4-8
Heat Sinks, 4-13
General Guidelines, 4-13
Installing, 4-13
Removing, 4-13
I
I/O and CMM Module
Installing, 5-6
Overview, 2-10
Removing, 5-6
System Board
Index
Installing, 5-8
Removing, 5-7
I/O Connectivity, 2-11
I/O Port Mapping, 2-11
Compute Blade, 2-11
I/O and CMM Module, 2-11
Information
General, 2-2
Necessary, 2-1
Precautions, 2-1
Recommended Equipment, 2-2
Recycling, 2-2
Safety, 2-1
Work Area, 2-2
M
Microserver
About, 1-1
features, 1-1
Models, 1-6
Overview, 1-1
Mid Plane
Features, 2-8, , 2-11
P
Parts
Accessories, 1-6
Contens, 1-6
List. See Catalog, 1-6
Power Supply Modules, 5-2
Installing, 5-3
Removing, 5-3
System Power Guidelines, 5-2
Processors, 4-9
General Guidelines, 4-9
Installing, 4-11
Removing, 4-9
S
System
Front View, 2-4
Internal View, 2-5
Overview, 2-3
Rear View, 2-4
Top Cover
Closing, 5-5
Opening, 5-5
D-1
System Board, 4-15
Bridge Board
Installing, 4-15
Removing, 4-15
Installing, 4-17
Removing, 4-16
System Memory, 4-5
General Guidelines, 4-5
Installing
Memory Module, 4-5
Population Rules, 4-5
Removing
Memory Module, 4-5
D-2
Index