Download Audio Phone - Intelligent Home Online
Transcript
DT-DJ4 Audio Phone User Manual 8888 1 2 Read this manual carefully before using the product, and keep it well for future use. 1. Parts and Functions 97.1 33.2 7 segment LED 187 150 8888 Handset 2 1 Up button Menu button Down button Cancel button Unlock 2nd button Unlock button Speaker Handset line Side View Key functions 7 segment LED Display setting informations Handset Pick up to communicate with visitor Hand line Connect handset with monitor Unlock button Press to release the door Unlock 2nd button Press to release the second door Up button Press to move up or increase the value Down button Press to move down or decrease the value Menu button Press and hold for 2s to open the setting menu shortcuts. Press to confirm settings. Cancel button Press to cancel the operations Speaker Send out vioce from the visitor 2. Operation Instructions 1) Door opening function:When visitor calls from outdoor station, the monitor rings, pick up handset to talk with the visitor, then press the Unlock button to open the door.If the system connect 2 locks,press Unlock 2nd button to open the second door. 2) Entrance monitoring: Pick up handset in standby mode,the LED will be shown a scroll information "Intr Call",press Up button or Down button to stop the scroll,and the LED show "ds-x"(x=1~4,refer to part 3-Numbers of door station),it means that the monitor switch "x" door station to mionitor.Press Up / Down button to increse/decrese the value,and press Menu button to confirm the setting. 3) Inner call: Use Up / Down button to select "-ALL" item on LED,then press Menu button to activate the inner call,all monitors connected to the system will ring at the same time.Pick up any monitor,the others will stop ringing immediately.(note that the user code must be the same for all monitors to activate the inner call function) 4) Intercom call:Use Up / Down button to select "C-xx" (xx=00~31,refer to part3Numbers of indoor monitor)item on LED,then press Up / Down button to increse/ decrese the value,and press Menu button to confirm the intercom calling.(note that the user code must be different for all monitors to activate the intercom call function) 3. Setup Instructions Press Menu button and hold for 2s in standby mode,the LED will be shown a scroll information "User Set-",press Up button or Down button to stop the scroll,and the LED show the setting items.Press Menu button to select setting items. Setting Item Door station call tone Intercom call tone LED state Description Default 1-xx Set the ring tone calling from outdoor station.Total 12 pieces ring tones can be selected(xx=01~12),press Up / Down button to increse/decrese the value,and press Menu button to confirm the setting. 02 2-xx Set the ring tone calling from intercom call or inner call.Total 12 pieces ring tones can be selected(xx=01~12),press Up / Down button to increse/decrese the value,and press Menu button to confirm the setting. 12 Setting Item LED state Ring volume 3-rx Set volume for call tone,rang from 0~9. 6 Speaker volume 4-Lx Set volume for speaker,adjust the voice from outdoor,rang from 0~9. 6 Microphone volume 5-tx Set volume for microphone,adjust the voice from user,rang from 0~9. 6 6-0x Maximum 4 door stations can be selected,this item is used to set the numbers of door station that can be surveilled by indoor monitor.refer to part 2 ->Entrance Monitoring. 1 Numbers of indoor monitor 7-xx Maximum 32 indoor monitors can be selected,this item is used to set the numbers of indoor monitor that can be selected to intercom.refer to part 2 ->Intercom call. 04 Keypad sensitivity 8-sx Rang from 0~2,The larger you set the value,the stronger it will be,"0"-slow,"1"-normal,"2"-fast. 1 Slave adress setting for monitor 9-dx Rang from 0~3,"0"-master monitor,"1~3"-slave monitor. 0 9-FS The restore to default function allows the user to recover the settings to factory setting.Select "9FS" item on LED,then press Up button,"YES"will be asked,press Up button again to restore the settings to default. - Numbers of door station Restore to default setting Description Default 4. Specification ●● Power Supply: DC24V ●● Power Consumption: standby 20mA,working 70mA ●● 7 segment LED: 4 digits dynamic ●● Wiring: 2 wires, non-polarity ●● Dimension: 187(H)X97(W)X33(D)mm The design and specifi cations can be changed without notice to the user. Right to interpret and copyright of this manual are preserved.