Download water wizard
Transcript
Technical Lighting Control WATERPROOF HOUSING FOR Pocket Wizard® Plus III USER MANUAL WATER WIZARD Foreword Technical Lighting Control would like to thank you for acquiring the Water Wizard housing for your Pocket Wizard Plus III transceiver. Technical Lighting Control is part of a group, along with Aquatica and Amphibico, of affiliated companies that dedicates themselves in the underwater imaging enthusiast the best instrument for their passion. The products are developed by and for demanding professional in this field. With regular maintenance, your Water Wizard housing will gives you years of faithful service, before using it, we recommend that you make yourself familiar with the Pocket Wizard® Plus III transceiver and take a moment to read this owner manual. Instruction: First unscrew the four hexagonal screws that close’s the front cover, remove this cover and place somewhere clean and safe. Plug in the mini phone jack into the transceiver; position it so that the dowel pin fits properly in the mounting hole in the back of the transceiver. Inspect and clean and lubricate the O-ring and close back the cover, tighten down the screws, making sure not to over torque them. Remove the bulkhead cap, inspect for cleanliness, lubricate the sync cord and/or extension cord O-ring and install in the Water Wizard bulkhead connector, connect the end of the sync cord to the camera housing or the underwater strobe(s). Most common sync cords used are: Ikelite to Nikonos single sync cord # 4104.31: For connecting the Water Wizard housing to most housing equipped with a Nikonos type of strobe connector Ikelite to Ikelite single cord # 4103.51: For connecting the Water Wizard housing to one Ikelite strobe or to any housing equipped with an Ikelite bulkhead. Ikelite to Ikelite double cord # 4103.52: For connecting the Water Wizard housing to two Ikelite strobes. Ikelite to Sea & Sea single cord # 4118.1: For connecting the Water Wizard housing to one Sea & Sea or Inon strobe. Ikelite to Sea & Sea double cord # 4118.2: For connecting the Water Wizard housing to two Sea & Sea or Inon strobes. Additional extensions are also available: Ikelite 4.5m/15ft extension cord # 4102.15 Ikelite 0.9/3ft extension cord # 4102.03 Check www.ikelite.com for additional sync cords combination. 3025 De Baene, Montreal, Quebec, Canada, H4S 1K8 [email protected] www.aquatica.ca Tel.: 514-737-9481 3 3 1 2 7 3 3 7 5 6 1) ON/OFF BUTTON 2) TEST / TRIGGER BUTTON 3) CLOSING FASTENER (4x) 4) HEXAGONAL KEY 5) CONNECTING BULKHEAD 6) BULKHEAD CAP 7) 1/4-20" THREADED MOUNTING HOLE 4 ® Pocket Wizard PLUS III in Water Wizard housing to camera housing Nikonos® strobe connector WATER WIZARD WATER WIZARD Made in CANADA 4104.31 Pocket Wizard PLUS III® in Water Wizard housing to two Ikelite® strobes 4103.52 4102.15 WATER WIZARD Made in CANADA 4102.15 PLUS III CH 17 ® Pocket Wizard PLUS III to Studio flash unit WATER WIZARD MODE A B TEST C D Made in CANADA SCHEMATIC USING STROBES, SYNC CORD AND EXTENSION FROM IKELITE® 4102.15 4103.51 Pocket Wizard PLUS III ® in Water Wizard housing to one Ikelite® strobe Pocket Wizard PLUS III® in Water Wizard housing used as receiver Standard Remote Grip Pocket Wizard PLUS III® in Water Wizard housing used as receiver WATER WIZARD WATER WIZARD PLUS III CH 17 MODE A B TEST C D Made in CANADA WATER WIZARD Made in CANADA IKELITE® 4102.03 IKELITE® 4102.15 Pocket Wizard PLUS III® in Water Wizard housing used as transmitter REMOTE TRIGGER SYSTEM WATER WIZARD IKELITE® 4104.31 Range of over 100m/ 325ft with a clear line of sight Standard Remote Grip is available in kit *Remote Bulkhead connector bulkhead supplied To remote control bulkhead # 18738 Housing remote control bulkhead* 19300 19304* 19302 19305* Nikon 10 pins Canon 3 pins # 19310 REMOTE CORD # 19311 REMOTE CORD To Camera remote control terminal