Download Instructions.

Installation Manual -YM11515
4 High Lattice - X Privacy Panel
Yardistry Ltd.
Mount Forest, ON Canada N0G 2L1
Toll Free Customer Support: 1.888.509.4382
[email protected]
www.yardistrystructures.com
Revised 04/13/2011
1
!Important Safety Notice!
•
Yardistry components are intended for privacy, decorative and ornamental use only. Product is NOT
INTENDED for the following:
- A safety barrier to prevent unsupervised access to pools, hot tubs, spas, or ponds.
- Safety railings for elevated platforms or decks.
- As load bearing support for a building, structure, heavy objects or swings. - Used in structures that trap
wind, rain or snow that would create extra load on the product.
•
Permanent structures may require a building permit. As the purchaser and or installer of this product you
are advised to consult local planning, zoning, and building inspection departments for guidance on applicable
building codes and or zoning requirements.
•
Wood is NOT flame retardant and will burn. Grills, fire pits and chimneys are a fire hazard if placed too
close to a Yardistry structure. Consult user’s manual of the grill, fire pit or chimney for safe distances from
combustible materials.
•
During installation, follow all safety warnings provided with your tools and use OHSA approved safety
glasses.
•
Some structures may require two or more people to install safely. Check for underground utilities
before digging or driving stakes into the ground!
General Information: Wood components are manufactured with Cedar (C. Lanceolata) which is protected with
factory applied water-based stain. Knots, small checks (cracks) and weathering are naturally occurring and do
not affect the strength of the product. Annual application of a water-based water repellent sealant or stain will help
reduce weathering and checks.
Keys to Assembly Success
Tools
Required
Warranty: Yardistry Limited products are backed by a 5 year limited lifetime warranty from the date of original
retail
purchase
and if installed as• Open
per manufacturer’s
installation
• Tape
Measure for manufacturing
• #1, defects
#2 & #3 Phillips
End Wrench
• 3/16”instructions.
Hex Key
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• Tape Measure
or Robertson Bits
(7/16”, 1/2” & 9/16”)
Patents Pending
or Screwdriver
• Adjustable Wrench
• Ratchet with extension Tools Required
• 1/8” & 3/16” Drill Bits
(1/2” & 9/16” sockets)
• Pencil
• #2 Phillips or Robertson
Bits or Screwdriver
Part
Identification
Key
• Carpenters
Level
On each page, you will find the parts
andDrill Bit
• 1/8”
• Carpenters
Square
quantities
required
to complete the assembly
Pencil
step illustrated on that page. Here• is
a sample.
• Standard or Cordless
Drill
Symbols
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
• Safety Glasses
• Adult Helpers
2X A1 Post 2 x 4 x83”
• 8’ Step Ladder
Quantity
Key Number
Part Description, Part Size
Throughout these instructions symbols are provided
as To
important
reminders
for proper and safe assembly.
Keys
Assemble
Success
This identifies information that requires special
attention. Improper assembly could lead to an
unsafe or dangerous condition.
Use
Help
Measure
Distance
Use
Help
Check that set or assembly is properly level
before proceeding.
Pre-drill 1/8” & 3/16” Bit
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to get help!
Check that assembly is square
before tightening bolts.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
Square
Assembly
Tighten
Bolts
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use a measuring tape to assure
proper location.
No
CAUTION – Protrusion Hazard
Use
Level
2
Yes
If Bolt protrudes
beyond T-Nut
Material List
R
(2) Top and Bottom Rail
S4
S4
PX1
S4
S7
#8 x 2 1/4” Wood Screw
S5
S4
S7
S5
#10 x 1” Pan Head Screw
(4) One High X Topper
S7
S7
S6
S5
#8 x 1 1/2” Wood Screw
S6
S5
S6
PL3
(6) Panel Clips
(4) Three High Lattice Panel
3
Step 1- Assemble Panels
1. Remove the upper metal connectors on both sides of PL3 - Three High Lattice Panel. Reattach the metal
connectors to PL3 by securing the bottom two holes of the metal connectors to the top two holes on PL3 so that
the metal connectors stick out from the top. Slide PX1 – One High X Topper between the two protruding metal
connectors on the top of PL3. Attach the metal connectors to PX1. (Fig. 1A) *Ensure Panels are oriented
correctly! (Fig. 1B)
2. Secure panels with a S4 - 2 1/4” Wood
Screw the location indicated by the large
arrow in the direction of the arrow.
Note PX1
orientation of keyhole.
3.Repeat until four panel assemblies are
created.
d reattach using
n panel.
Tenga en cuenta la orientación
del agujero de la cerradura.
y vuelva a
eros
Notez l'orientation de l'encoche
en trou deserrure.
accordement et
n des deux trous
été percés à
Pilot holes to the right
Fig. 1B - Filler Strips on Bottom
of Panel!
x4
Fig. 1A
Do not remove Small Connector
PL3
No retire los conectores
Ne retirez pas les petites pièces d
raccordement.
4x
PX1
One High X Topper
4x
PL3
Three High Lattice Panel
4x
4
S4
#8- 2 1/4” Wood Screws
Step 2- Assemble Wall
Fig. 1
1. Assemble panels together in
configuration shown. (Fig.1) Insert
male connector into female. Slide
down until flush with
adjacent
Pautas
básicas para Instruc
Instructionspanel
de base
Cut
and
pour l'T
el ensamblado
de attach
Basic
Guidelines
as shown. (Fig.
1A)
des pa
3
Pautas básicas para
for Panel Assembly los paneles
l'assemblage
pour
assem
el ensamblado de
Las ilustraciones
muestran y fije Les
here are configurations
using
Corte
los
r
2. SShown
ecure
Panels
with
S4
2
1/4”
pièces
supé
des
panneaux
configuraciones
con
topes.
También
a Topper. 2 and 3 High Panels can
los paneles
également
conectar 2 y 3 paneles
also be connected
together as
screws
provided
inse pueden
pre-drilled
1 Assemble Toppers to Panels.
Instale los topes en los paneles.
Basic Guidelines
for Panel Assembly
Assemblez les pièces supérieures
et les panneaux.
à deux ou à
Les assemblages illustrés
comportent des altos a medidaTaillez
que se adquieran.
purchased.
et fixez
(vendus sél
*Use
los arrows,
tornillos de acero inoxidable
as indicated
by
in
*Use 2possible
1/4" stainless
steel screws
pièces supérieures. Ilholes
est
*Utilisez les
de
2
1/4"
que
se
incluyen
en
el
juego
included in the Panel Clip set to
2-1/4 po fou
de arrow.
sujetadores de One
paneles para
the
direction
of
the
(Fig.1)
également d'assembler
des
panneaux
Wide
Anch
secure
and
strengthen
the
assembly.
3 wide x 3 high)
B. Assemble Panels side by side. (Maximum
fixations
po
reforzar el ensamblado.
de renforce
à deux ou à troisConecte
carreaux
de
hauteur
20"
los paneles lado a lado.
(vendus séparément).
Assemble
Assemblez
à côte.Panels side by side.
2 les panneaux côte
*Utilisez les vis en acier inoxydable de Conecte
Fig. 1Alos paneles lado a lado.
à côte.Anc
2-1/4 po fournies dans le nécessaire deAssemblez les panneaux
Two côte
Wide
fixations pour panneaux afin de fixer et
Instructions
de base
Cut and attach3T
de renforcer l'assemblage.
Shown here are configurations using Las ilustraciones muestran
configuraciones con topes. También
a Topper. 2 and 3 High Panels can
se pueden conectar 2 y 3 paneles
also be connected together as
altos a medida que se adquieran.
purchased.
*Use los tornillos de acero inoxidable
*Use 2 1/4" stainless steel screws
de 2and1/4"
que se incluyen en el juego
included in the Panel Clip set
to Large Connectors
Remove
reattach using top two
factory drilled holes onde
panel.
sujetadores
de paneles para
secure and strengthen theRetire
assembly.
los conectores grandes y vuelva a instalarlos
reforzar
el del
ensamblado.
usando los dos agujeros
pretaladrados
panel.
+
=
Pautas básicas para
pour l'assemblage
Note
Tenga en cuenta Notez l'orientation
el ensamblado de
Basic Guidelines
orientation la orientación del de l'encoche en
des
panneaux
trou de serrure.
of keyhole. agujero
de la
losPanels
paneles
Assemble
side by side.
for Panel Assembly
cerradura.
2
Retirez les grandes pièces de raccordement et fixez-les
de nouveau au moyen des deux trous
supérieurs du panneau qui ont été percés
à l'usine.
3
Corte y fije los r
Three Wide
Anc
Les assemblages illustrés comportent des
Taillez et fixez l
ilustraciones
Conecte
los
panelesmuestran
lado a lado. pièces supérieures. Il est possible
Shown here are configurations
using Las
configuraciones
con
topes.
También
a Topper. 2 and 3 High Panels can
également d'assembler des panneaux
One Wide
Anch
Assemblez
les panneaux
côte à côte.
se pueden
conectar 2 y 3 paneles
Insert male into female. Slide down until flush with adjacent panel
also be connected together as
à
deux
ou
à
trois
carreaux
de
hauteur
20"
Four
Wide
Anc
altos a medida que se adquieran.
Introduzca el extremo macho en el extremo hembra.
Deslícelo
ha
3. Connect
last asse
purchased.
(vendus
séparément).
abajo hasta que quede al ras del panel adyacente.
*Use los tornillos de acero inoxidable
*Use 2 1/4" stainless steel screws
en acier
inoxydable
de
male
into
Slide down
until
with
Insérez
les female.
pièces de raccordement
mâles
dansflush
les pièces
de 2 1/4" que se incluyen en el juego *Utilisez les vis Insert
included in the Panel Clip set to
adjacent
panel.
de
raccordement
femelles.
Faites glisser le panneau
2-1/4
po
fournies
dans
le
nécessaire
de
Two Wide
Anc
vers le bas jusqu'à ce qu'il soit au même niveau que
secure and strengthen the assembly. de sujetadores de paneles para
Introduzca
el extremo
pour panneaux
afin
de
fixermacho
et en el extremo hembra.
ez l'orientation
le panneau
adjacent.
Fig.fixations
2
3
reforzar el ensamblado.
Deslícelo hacia abajo hasta que quede al ras del
encoche en
panel adyacente.
denotrenforcer
l'assemblage.
R
Do
remove Small Connectors.
3.
S
ecure
R-Top
and
de serrure.
No retire los conectores Insérez les pièces de raccordement mâles dans les
Bottom Rails to Panel
pequeños.
pièces de raccordement femelles. Faites glisser le
Three Wide
Assemble
Panels
side
by
side.
panneau vers le bas jusqu'à ce qu'il soit au même
Ne retirez pas les petites pièces
Note wood piece at bottom prevents
Assembly with S4 - 2 1/4”
niveau que le panneau adjacent.
de raccordement.
collection of water.
losinferior
paneles lado a lado.
Wood Screws locations NoteConecte
que la pieza de madera
evita la acumulación de agua.
indicated by arrows in Prenez
Assemblez
les panneaux côte à côte.
note que la pièce en bois
située au bas de chaque élément
the direction of the arrow.
de l'assemblage empêche
Four Wide
l'accumulation d'eau.
Insert
male into female. Slide down until flush with adjacent panel.
(Fig. 2)
2
Anc
Anc
Introduzca el extremo machoAsegure
en elel extremo
hembra.
Deslícelo
hacia
3. Connect
last assembled
panels to make a fence section.
*R- Top and Bottom Rails
Los torn
ensamblado usando tornillos*. Use los agujeros pretaladrados.
y se incluyen
abajo
hasta
que
quede
al
ras
del
panel
adyacente.
Fixez
l'assemblage
au
moyen
de
vis.*
Servez-vous
des
trous
prépercés
à
l'usine.
ez l'orientationwill overhang 1/4” on
*Les vis sont celles de 2-1/4 po en acier inoxydable qui sont fournies dans le
encoche en either
side
panel.
Insérez
les of
pièces
de raccordement mâles dans les pièces
Secure with Screws*. Use factory drilled holes.
de serrure.
de raccordement femelles. Faites glisser le panneau
vers le bas jusqu'à ce qu'il soit au même niveau que
le panneau adjacent.
panel_cap_labels_19x9.5.indd 7
Top and Bottom Railmale
will
connector
overhang 1/4"on either
side.
the male connectors from the outside of the
C. Remove
Attach Top with Screws*
conector
panel assembly.
*RTop
and
Bottom
Rails
all Connectors.
through factory drilledmasculino
holes.
Quite los conectores masculinos del exterior de la
may need to be cut to
On
Bottom,
space
Screws*
connecte
asamblea
de
panel.
tores
mâle
Insert male into female. Slide down until flush with adjacent panel.
4" from edges of panels.
6’ 6 1/2” (2m)
Enlever les connecteurs mâles de l'extérieur de
l'assemblée de panneau.
Deslícelo
hacia
3. Connect
last assembled
panels to make a fence section.
petites pièces(It is recommended toIntroduzca el extremo macho en el extremo hembra.
abajo hasta que quede al ras del panel adyacente.
short male
connector
use a Mitre Box or Mitre
Saw)
Insérez
les pièces de raccordement mâles dans les pièces
de raccordement femelles. Faites glisser le panneau
vers le bas jusqu'à ce qu'il soit au même niveau que
le panneau adjacent.
all Connectors.
2x
R
tores
y drilled holes.
pretaladrados.
petites pièces
ercés à l'usine.
Top & Bottom Rail
24x
S4
#8- 2 1/4” Wood Screws
Screws* are 2 1/4" stainless
steel included in Panel Clip set.
conector
masculino
corto
le connect
1/4"
mâle court
Top and R
Bottom Rail will
overhang 1/4"on either side.
Attach Top with Screws*
1/4" factory drilled holes.
through
On Bottom, space Screws*
4" from edges of panels.
Los tornillos* son de acero inoxidable de 2 1/4"
y se incluyen en el juego de sujetadores de paneles.
*Les vis sont celles de 2-1/4 po en acier inoxydable qui sont fournies dans le nécessaire de fixations pour panneaux.
5
1/4"
Step 3- Installing Panel Clips
1. Postition Panel Clips in locations indicated in Figures 1 and 1A. Ensure Panel Clips are oriented in the
same direction facing outside the Pergola!
2. Panel Clips should be placed in the centre of the post or the leading edge of the clip should be 1 3/8” or 3.5cm
away from the side of the post as shown in Fig. 2.
3. With Panel Clips in place, mark screw holes with a pencil and pre-drill holes with a 1/8” drill bit. (Not provided)
4. Secure Panel Clips in locations indicated in figure 1 and 1A with S7- #8 x 1 1/2” wood screws.
Fig. 1A
(Outside
Pergola)
(Inside
Pergola)
1 3/8”
(3.5cm)
Pre-drill holes and secure with S7- #8 x
1 1/2” Wood Screws
Fig. 1
75”
40”
(190.5cm)
(101.6cm)
(25.3cm)
12x
P
4x4 Post
6x - Panel Clips
12x S7 #8 x 1 1/2” Wood Screw
6
Step 4- Installing Wall Into pergola
1. With the help of an adult, place the Wall on Panel Clips as shown (Fig.1)
allowing a 4” gap between the bottom of the post and the bottom edge of
the bottom rail on the panel assembly.
2. With a 1/8” drill bit, predrill holes as shown in figure 2.
3. Fasten the Wall to the post and Panel Clips with a S5- 1” Pan Head Screw
provided in location of arrows. (Fig. 1)
Fig. 2. Predrill Holes and Fasten
with S5- 1” Pan Head Screw
Fig. 1
(10.2cm)
12x
P
4x4 Post
6x S5
7
#10 x 1” Pan Screws