Download ML610Q380/383/384/385 Reference Board User`s Manual

FJBL610Q380RB-01
LAPIS Semiconduter CO., Ltd.
May.26,2015 (Rev. 1.00)
ML610Q380/383/384/385 Reference Board User's Manual
ML610Q380/383/384/385 Reference board is prepared by LAPIS Semiconduter to have you study the operations of
ML610Q380/383/384/385.
The board is arranged so that necessary components are mounted by you according to your purpose, then only minimum necessary
components are mounted on the board by LAPIS Semiconduter for brief use of ML610Q380/383/384/385.
By using the board with "uEASE on-chip debug emulator" (hereinafter referred to "uEASE") and "free sample U8 Development Tools
CD-ROM" which is bundled in the package of uEASE not only Software development/debugging but also writing Flash ROM in the
devices are capable.
This board also works in stand alone mode with external power suppy without uEASE.
Before starting works with this board, read below carefully and understand notices.
1. The board features
Incorporates ML610Q380 or 80pin IC-Socket for ML610Q380/383/384/385
Supports flash ROM programming and on-chip debugging (using TEST0 and TEST1_N pins)
High extendibility; Through-holes for your peripheral board are equipped with microcontroller pins
The power supply used can be selected ( uEASE or peripheral board )
Prepared the pad to mount parts ( parts necessary for microcontroller operation )
2. The board hardware specifications
Please refer to the reference schematics for detail on connections of each hardware parts.
Embedded microcontroller
U1: 80pin IC socket for ML610Q380/383/384/385
PWR1 – PWR3: Jumper for input power supply switch ( 3pin pin-header and short pin )
AOUT2: Connection switch of a LINE output and a speaker amplifier analog input
( 3pin pin header and a short pin)
J1-J9: Jumper for CNSDCB2 ( 3pin pin header and a short pin)
RESET_SW: Reset switch for M25PE16
SPEAKER: Jack for speaker connection
R4 – R6: Resistance for LCD driver power supply
R9: Pull-up resistance for RESET_N
R10 – R13: Resistance for light emitting diodes (P20-P23)
Embedded parts
P20 - P23: Light emitting diodes
CNUE: Connector for on-chip debug emulator ( 14pin connector )
CNSDCB2: Connector for Sound Device Control Board2( SDCB2) ( 14pin connector )
C4 – C6: Capacitors for LCD driver ( 3pieces )
C9, C12-C13, C21, C23-C24, C28-C29, C30, C32: Capacitors for power supply ( 10 pieces )
C10-C11 or C15-C16: Capacitors for XTAL( 2pieces )
C22: Capacitor for DC voltage elimination ( 1pieces )
C26: Capacitor for reset ( 1pieces )
XT_2: 32.768kHz oscillator ( 1pieces )
OSC_2: 8MHz oscillator ( 1pieces )
AIN0-AIN7: Pads for SA-ADC input voltage
Pads for mounting
CN1 - CN4: Pads for peripheral board connectors ( 10pin x 4, 2.54mm pitch )
PP7-PP10: Land for light emitting diodes (P20-P23)
Other useful pads
Operating voltage
Board size
DVDD, EXVDD, VSS, VREF, AIN0-AIN7
DVDD=+2.2V - +5.5V（DVDD=+4.5V - +5.5V during playback using internal speaker）,
VREF=+4.5V - +5.5V
110.00 x 140.00 mm
FJBL610Q380RB-01
LAPIS Semiconduter CO., Ltd.
May.26,2015 (Rev. 1.00)
3. Parts layout
VSS
EXVDD
CNSDCB2
CNUE
PWR1
PWR2
LAPIS
PWR3
CN3
J1 – J6
SPEAKER
U2
IC socket
P20-P23
U1
ML610Q380
CN2
CN4
VREF
AIN0-AIN3
RESET SW
J7 – J9
CN1
AOUT2
XT_2
< fig.1 Parts layout >
L610Q380
XXXXXXJ
1pin
1pin Mark
< fig.2 Device set direction >
OSC_2
FJBL610Q380RB-01
LAPIS Semiconduter CO., Ltd.
May.26,2015 (Rev. 1.00)
4. Jumper( 3pin pin-header and short pin ) set up
PWR1, AOUT2 jumper is set as follows.
Short (1) and (C)
Short (C) and (3)
(1) (C) (3)
(1) (C) (3)
PWR
USR：Use of user’s power supply
SYS：Use of uEASE power supply
AOUT
SPIN：Use of internal speaker amplifier
LINE：Use of external speaker amplifier
Jumper Pin No.
PWR2, PWR3, J1－J8 jumpers shall be used by default status as follows.
Jumper Pin No.
The condition of connection
PWR2
(1) (C) (3)
Short (C) and (3)
PWR3
(1) (C) (3)
Short (C) and (3)
J1
(1) (C) (3)
Short (1) and (C)
J2
(1) (C) (3)
Short (1) and (C)
J3
(1) (C) (3)
Short (1) and (C)
J4
(1) (C) (3)
Short (1) and (C)
J5
(1) (C) (3)
Short (1) and (C)
J6
(1) (C) (3)
Short (1) and (C)
J7
(1) (C) (3)
Short (1) and (C)
J8
(1) (C) (3)
Short (1) and (C)
J9
(1) (C) (3)
Short (1) and (C)
FJBL610Q380RB-01
LAPIS Semiconduter CO., Ltd.
May.26,2015 (Rev. 1.00)
5. Notes on use
(1) The information contained herein can change without notice owing to product and/or technical improvements.
Before using the product, please make sure that the information being referred to is up-to-date.
(2) Before using this board, read carefully and understand the contents of the ML610Q380/383/384/385 user's manual and the uEASE
user's manual.
(3) The engineering sample of ML610Q380 might be mounted on the board.
Therefore, please confirm the characteristic finally by using MP of ML610Q380 and customer's mass production boards.
(4) LAPIS Semiconduter will not provide any support for this board, but the board can be exchanged with a new product only when it
has an initial failure.
(5) The device must be set under the condition that the power supply of the reference board is cut off. And, the reference board is to
set it in the case of "the socket type" not to mistake the direction of the device. When a cap is opened, 1 pin direction is the
bottom left side. Refer to < fig.2 Device set direction >.
(6) It is the pin for a check pin EXVDD to supply a power supply from the outside. Set up PWR1 on the “USR” side at that time.
(7) Notes when the PWR jumper is set to USR side and the uEASE is connected.
Turn on the power supply of the peripheral board after starting the uEASE..
Moreover, Stop the uEASE after turning off the power supply of the peripheral board.
(8) When the PWR jumper is set to the uE side, the ability to supply power of the uEASE is +3.3v/100mA.
(9) Notes when the RESET_N signal is prepared on the peripheral board side.
If you use the uEASE, open or set DVDD-level RESET_N signal pin (CN1_11pin).
(10) There is a possibility of short the circuit when using it on electro conductive so that the board may have the pattern on the solder
side. Therefore, please use the board on nonconductivity or put the protection parts on the solder side if necessary.
(11) When you use SA-ADC:
When input of the ADC is connected to AIN0-AIN7 on this board, please cut the pattern of AIN0-AIN7 as needed.
And please input from a hall of that is near to a device, as shown in the < fig3 >.
VREF is connected to VDD by a jumper. Please set the VREF jumper in the USER side when any voltage wants to input.
And please input the VREF voltage from CN4_16 pin (VREF_IN). Please refer to < fig4>.
(10) When you don’t use light emitting diodes:
P20-P23 can drive direct to light emitting diodes. P20-P23 are wired with light emitting diodes through PP7 – PP10.
Please cut the land of the PP7 – PP10 when you don’t use light emitting diodes, as shown in the < fig.6 >.
(11) When you use light emitting diodes:
Between VL3 and VDD, tip resistance of 2012 size can be implemented.
Please implement tip resistance as needed in PP1/PP4. Please refer to <fig6>.
(12) When P10-P11 is used as a general-purpose input port.
P10-P10 can be used high-speed oscillator port and a general-purpose input port.
When you use it as a general-purpose input port, remove 8MHz oscillator, and short PP2 and PP5, PP3 and PP6 respectively,
as shown in the < fig.7 >.
FJBL610Q380RB-01
LAPIS Semiconduter CO., Ltd.
May.26,2015 (Rev. 1.00)
Top View
Input it directly from this hall
after cutting. after cutting.
Input it directly from this hall
after cutting. after cutting.
< fig.3. AIN0-AIN7 >
Top View
Short
Cut LAND
< fig4. VREF >
Top View
Cut LAND
< fig5. light emitting diodes(P20-P23) >
FJBL610Q380RB-01
LAPIS Semiconduter CO., Ltd.
May.26,2015 (Rev. 1.00)
Top View
< fig6. LED >
Top View
Remove
Short
< fig7. OSC_2 >
6. Reference schematics:
The reference circuit diagram of this reference board is shown after the following page
A
B
C
D
RVDD
SDCB2_RSTB
IN
IN
2
IN
VDDL
VPP
PVPP
1/4D,2/2B
IN
IN
200K
R5
2
1
200K
R6
2
1
3
2
1/4B,2/2B
DVSS
1 PP6 2
2 1
12PF
1
1 PP5 2
C15
OSC_2
C16
12PF
10UF
2 1
C12
C13
2 1
1 10UF
200K
R2
1
2
200K
R3
1
2
2
DVSS
P10
P11
PIN[80:1]
200K
R4
2
1
IN
IN
XT_2
1
DVSS
DVSS
1/4D,2/2B
560
PP4 1
PIN20
PIN13
PIN12
1/3B,2/4A,2/2B
1/3B,2/3A
1 2
C4
0.22UF
3
1 2
C5
0.22UF
1 2
C6
0.22UF
DVSS
1/4B,2/2B
PIN11
IN
DVSS
1 2
C3
0.22UF
2
12PF
C11
1 PP2
2
1
2
12PF
2
1 PP3
1
2
C9
DVSS
3
P20
PIN63
DVDD
1/3B,2/3A
1 2
C2
0.22UF
560
P21
LED
1 PP7 2 2
1 1R10 2
PIN64
PIN21
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PIN1
PIN2
PIN3
PIN4
PIN5
PIN6
PIN7
PIN8
PIN9
PIN10
PIN11
PIN12
PIN13
PP1 1
1 2
C1
0.22UF
560
LED
1 PP8 2 2
1 1R11 2
2
2
2
200K
R1
1
VDDL
VPP
PVPP
P22
P23
LED
1 1R12 2
1 PP9
PIN65
PIN40
PIN39
PIN38
PIN37
PIN36
PIN35
PIN34
PIN33
PIN32
PIN31
PIN30
PIN29
PIN28
PIN27
PIN26
PIN25
LAPIS SEMICONDUCTOR CO.,LTD
TITLE
ML610Q380/385 Reference Board
APPLICATION
ML610Q380 / ML610Q385
DWG NO
2/2A
DRAWN By
QTS-11550
SHEET
1 of 2
1
A
LED
1 PP10 2 2
1 1R13 2
560
U2
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
P44/AIN4
P45/AIN5
P46/AIN6
P47/AIN7
P34/PWM4
P35/PWM5
P40/SDA
P41/SCL
P42/RXD0
P43/TXD0
RESET_N
VSS_12
DVDD
VDDL
XT0
XT1
VPP
P10/OSC0
P11/OSC1
P51(TESTO1)
C32 10UF
2 1
PC3/SEG11
PC2/SEG10
PC1/SEG9
PC0/SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0
COM0
COM1
COM2
COM3
VL3
VL2
VL1
P52(TSETO2)
IC SOCKET
DVSS
DVSS
PIN66
1 2
PIN56
PIN55
PIN54
PIN53
PIN52
PIN51
PIN50
PIN49
PIN48
PIN47
PIN46
PIN45
PIN44
PIN43
PIN42
PIN41
SPM
SPP
P20/LED0
P21/LED1
P22/LED2
P23/LED3
VSS_67
P50(TESTO0)
P53(TESTO3)
NC(PVPP)
P5VDD(VDDR)
P00/INT0
P01/INT1
P02/INT2
P03/INT3
VREF
P30/AIN0
P31/AIN1
P32/AIN2
P33/AIN3
2
IN
IN
IN
1
SPVSS
SPVDD
SPIN
AOUT
SG
TSET1_N
TSET0
NMI
PD7/SEG23
PD6/SEG22
PD5/SEG21
PD4/SEG20
PD3/SEG19
PD2/SEG18
PD1/SEG17
PD0/SEG16
PC7/SEG15
PC6/SEG14
PC5/SEG13
PC4/SEG12
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
1UF
C24
PIN21
PIN20
0.1UF C23
2
AOUT2
1UF
2 1
1
VREF
2
3
2 1
2/2D
IN
VREF_IN
PIN72
PIN73
PIN74
PIN75
PIN76
PIN77
PIN78
PIN79
PIN80
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
2
J10
PIN61
PIN62
PIN63
PIN64
PIN65
PIN66
PIN67
PIN68
PIN69
DVSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PIN1
PIN2
PIN3
PIN4
PIN5
PIN6
PIN7
PIN8
PIN9
PIN10
PIN11
PIN12
PIN13
1UF
10UF
1
2
C10
10K
1 R9 2
DVSS
PIN56
PIN62
PIN61
C21
SPVSS
SPVDD
SPIN
AOUT
SG
TSET1_N
TSET0
NMI
PD7/SEG23
PD6/SEG22
PD5/SEG21
PD4/SEG20
PD3/SEG19
PD2/SEG18
PD1/SEG17
PD0/SEG16
PC7/SEG15
PC6/SEG14
PC5/SEG13
PC4/SEG12
PIN76
DVSS
OSC_1
2
1
P10
P11
A2-3PA-2_54DSA
3
1
J9
2
J8
A2-3PA-2_54DSA
3
1
2
A2-3PA-2_54DSA
3
1
C26
1UF
2 1
USR
XT_1
1
DVDD
4
PIN40
PIN39
PIN38
PIN37
PIN36
PIN35
PIN34
PIN33
PIN32
PIN31
PIN30
PIN29
PIN28
PIN27
PIN26
PIN25
VCC
DVDD
1/3D,2/4A,2/2B
1/3D,2/3A
1/3D,2/3A
2
SDCB2_SO
IN
2
3
1
RESET_SW
PUSHSW
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
C27
1
C7
J6
10UF
2 1
2
2
DVSS
J7
A2-3PA-2_54DSA
1
3
2/2A
2.2UF
2 1
C8
2
A2-3PA-2_54DSA
3
1
U1
DVDD
1UF
J5
A2-3PA-2_54DSA
1
3
SDCB2_SI
OUT
3
2 1
2
DVSS
PIN68
0.022UF C22
2
PIN21
PIN12
J4
A2-3PA-2_54DSA
1
3
2/2A
DVSS
PC3/SEG11
PC2/SEG10
PC1/SEG9
PC0/SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0
COM0
COM1
COM2
COM3
VL3
VL2
VL1
P52(TSETO2)
ML610Q380
ML610Q385
DVSS
SPIN 1 2
DVSS
DVDD
P44/AIN4
P45/AIN5
P46/AIN6
P47/AIN7
P34/PWM4
P35/PWM5
P40/SDA
P41/SCL
P42/RXD0
P43/TXD0
RESET_N
VSS_12
DVDD
VDDL
XT0
XT1
VPP
P10/OSC0
P11/OSC1
P51(TESTO1)
SDCB2_WB
SPM
SPP
P20/LED0
P21/LED1
P22/LED2
P23/LED3
VSS_67
P50(TESTO0)
P53(TESTO3)
NC(PVPP)
P5VDD(VDDR)
P00/INT0
P01/INT1
P02/INT2
P03/INT3
VREF
P30/AIN0
P31/AIN1
P32/AIN2
P33/AIN3
LINE
DVDD
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
C17
2/3A
IN
PIN72
PIN73
PIN74
PIN75
PIN76
PIN77
PIN78
PIN79
PIN80
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
C30
2
2 1
J3
A2-3PA-2_54DSA
1
3
PIN76
2 1
2
PIN20
2
C14 1UF
J2
A2-3PA-2_54DSA
1
3
SDCB2_SCK
PIN61
PIN62
PIN63
PIN64
PIN65
PIN66
PIN67
PIN68
PIN69
DVDD
PIN56
PIN55
PIN54
PIN53
PIN52
PIN51
PIN50
PIN49
PIN48
PIN47
PIN46
PIN45
PIN44
PIN43
PIN42
PIN41
1UF
2 1
PIN69
C20 10UF
2
DVSS
VCC
PIN13
J1
A2-3PA-2_54DSA
1
3
SDCB2_CSB
IN
0.1UF C19
1 2
0.022UF C18
2/2A,2/2D
2/3A,2/2B
3 T
2 B
1 S
MJ-354A0
SPIN 1 2
DVSS
IN
U4
A2-3PA-2_54DSA
1
3
DVSS
2
AOUT1
LINE
PIN56
DVSS
DVDD
R8 10K
1
2
8
7
6
5
C25 2.2UF
VCC
RST/
C
D
2 1
1 S/
2 Q
3
4 W/
VSS
10K
1 R7 2
SOP8
U3
A2-3PA-2_54DSA
1
3
AOUT
M25PE16
1
DVDD
2/2C
OUT
B
C
D
REV
1.00
4
A
B
1
AIN4
I/O
PIN1 1/3C
P45/AIN5
I/O
PIN2 1/3C
1 AIN5 2
P46/AIN6
I/O
PIN3 1/3C
1 AIN6 2
P44/AIN4
C
DL
2
1
1
P47/AIN7
I/O
PIN4 1/3C
P34/PWM4
P35/PWM5
P40/SDA
P41/SCL
P42/RXD0
P43/TXD0
RESET_N
I/O
I/O
I/O
I/O
I/O
I/O
I/O
PIN5
PIN6
PIN7
PIN8
PIN9
PIN10
PIN11
P10
P11
P51(TESTO1)
2
IN
IN
I/O
PIN20
CN1
CN20P-1
CN2
CN20P-2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1 AIN7 2
1/3C
1/3C
1/3D,2/3A
1/3D,2/3A
1/3D,2/3A
1/3D
1/3D
1/4B,1/4D
1/4D,1/4B
1/1D,2/3A
P52(TESTO2)
OUT
1/1D
COM3
COM2
COM1
COM0
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
PC0/SEG8
PC1/SEG9
PC2/SEG10
PC3/SEG11
OUT
OUT
OUT
OUT
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
1/2C
PIN21 21
22
23
24
PIN25 25
PIN26 26
PIN27 27
PIN28 28
PIN29 29
PIN30 30
PIN31 31
PIN32 32
PIN33 33
PIN34 34
PIN35 35
PIN36 36
PIN37 37
PIN38 38
PIN39 39
PIN40 40
DVDD
PC4/SEG12
PC5/SEG13
PC6/SEG14
PC7/SEG15
PD0/SEG16
PD1/SEG17
PD2/SEG18
PD3/SEG19
PD4/SEG20
PD5/SEG21
PD6/SEG22
PD7/SEG23
NMI
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
SG
AOUT
I/O
I/O
1/1B
1/1B
1/1D
1/1B
1/1B
1/1B
1/1B
1/1B
1/1B
1/1B
1/1B
1/1B
1/1B,2/3A
PIN41
PIN42
PIN43
PIN44
PIN45
PIN46
PIN47
PIN48
PIN49
PIN50
PIN51
PIN52
PIN53
1/1B
1/1A
PIN56
DVSS
DVSS
CNSDCB2
CN14P
1/1D,2/2D
1/4A
1/3A
1/3A
1/1D,2/2B
1/2A
1/3D,2/2B
1/1B,2/2C
1/3D,2/2B
1/3D,1/3B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PIN69
PIN20
PIN9
PIN53
PIN7
1/3D,2/2B
PIN8
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
SDCB2_CSB
SDCB2_RSTB
SDCB2_SO
SDCB2_SI
SDCB2_SCK
SDCB2_WB
SDCB2_SEQ0
SDCB2_CSELB(NMI)
SDCB2_SIN330
PVPP
OUT
SDCB2_SCK330
DVSS
DVDD
VCC
CN3
CN20P-3
CN4
CN20P-4
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
P20/LED0
P21/LED1
P22/LED2
P23/LED3
I/O
I/O
I/O
I/O
1/2C
1/2C
1/2C
1/2C
PIN63
PIN64
PIN65
PIN66
P50(TESTO0)
P53(TESTO3)
OUT
OUT
1/3A
1/1D,2/2A
PIN68
PIN69
P00/INT0
P01/INT1
P02/INT2
P03/INT3
VREF_IN
I/O
I/O
I/O
I/O
I/O
1/2C
1/2C
1/2C
1/2C
1/2C
PIN72
PIN73
PIN74
PIN75
P30/AIN0
I/O
1/2C
PIN77
PIN78
PIN79
PIN80
2
1 AIN0 2
DVSS
1
P31/AIN1
I/O
1/2C
P32/AIN2
I/O
1/2C
1
P33/AIN3
I/O
1/2C
1
AIN1
AIN2
AIN3
2
2
2
RVDD
3
3
PIN55
IN
1/1B
PIN54
I/O
1/3D,1/3B,2/2B
IN
TEST0
VDDL
SYS
4
1
U5
1 GND
NC5 5
2
VIN
3
4
VOUT NC4
2 1
C29 0.1UF
DVDD
2 1
1
C28 0.1UF
uE
2
PWR1
DVSS
A2-3PA-2_54DSA
1
3
VSS
3V
MC78LC33NTRG
DVDD
1
3V
DVDD
2
TEST1_N
1/1B
DVDD
PWR3
VPP
A2-3PA-2_54DSA
1
3
IN
2
1/3B,1/3D
PWR2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A2-3PA-2_54DSA
1
3
CNUE
CN14P
LAPIS SEMICONDUCTOR CO.,LTD
TITLE
DVSS
ML610Q380/385 Reference Board
APPLICATION
EXVDD
ML610Q380 / ML610Q385
DWG NO
DRAWN By
A
B
C
QTS-11550
SHEET
2 of 2
D
REV
1.00
4