Download Hawker SEA FURY
Transcript
Thank you for choosing CYmodel Global : www.cymodel.com Australia : www.austars-model.com Italia : www.biellaexpress.com Hawker SEA FURY Item Nr: Cy8029 Instruction Manual Before commencing assembly,please read these instructions thoroughly. SAFETY PRECAUTIONS This radio control model is not a toy! lFirst-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent. lAssemble this kit only in places out of children ,s reach! lTake enough safety precautions prior to operating this model. , You are responsible for this models ass embly and safe operation! lAlways keep this instruction manual ready at hand for quick reference,even after completing the assembly. lCould cause serious injury or even death SPECIFICATION Wing Span.......2420 mm (95.2 in) Wing Area.......91.4 dm2(1418 sq.in) Takeoff weight....9.4 kg Length..............2204 mm (86.7in) Engine..............100-150cc gas engine Radio................6 channels, 10 servos Designed and Manufactured by : CYmodel Http : // www.cymodel.com REQUIRED FOR OPERATION (Purchase separately) A minimum 6 channel radio for airplanes (with 10 servos). And dry batteries. 1 ! 4 CAUTION: Only use a minimum 6 channel radio for airplanes! (No other radio may be used!) 5 A minimum 6 channel transmitter for airplanes. Silicone Tube Fuel Filter Glow engine fuel only. required for engine starting ! WARNING: Normal gasoline cannot be used with glow engines. Fuel Pump Plug Wrench 12 AA-size Batteries For handing the radio properly.refer to its instruction manual. 36 Engine and Muffler 2 Glue Model Airplane engine 100-150 cc gas engine 3 37 Ignition Muffler Epoxy Glue Instant glue Other equipment for enhancing airplane operation & perormance Purchase a propeller that will match your engine Propeller splinner Engine Starter 12V Battery (for starter) TOOLS REQUIRED ( Purchase separately) Sharp Hobby Knife Needle Nose Pliers Phillips Screw Driver Awl Wire Cutters Scissors BEFORE YOU BEGIN . Read through the manual before you begin ,so you will have an overall idea of what to do. 2 . Check all parts .if you find any defective or missing parts .contact your local deater. 3 . Symbols used throughout this instruction manual,comprise. 1 A B Apply epoxy glue. Drill holes with the specified Diameter(here:2mm) Must be purchased separately! Apply instant glue (CA glue,super glue). Ensure smooth non-binding movement while assembling. Pay close attention here! Assemble left and right Sides the same way. Cut off shaded portion. 2mm Cut off excess. 2 £¡Warning! ! Do not overlook this symbol. ! 3 Accessory list for this page. Apply instant type A/B glue to aileron and pin hinge 2.3x8mm Tp Screw Make sure hings are mounted in the same line ----4 Pin hings ---8 Hinge A -----8 B Pin hings -----------8 1 4 Install the navigation lights to the wing Install the aileron Aileron Tie a weight to a piece of string. Lower the string into the wing from the root, Let the weight drop out through the wing .A Tailing edge C A B Warning! Securely glue together. If coming off during flights,you'll lose control of your airplane which leads to accidents! 2 5 Install the lamp-chimuey to the wings Blcak line Epoxy the flap to the wing as illustration Battery 1.5V 1.5V Red line 2.3x8mm Tp Screw A --4 B Hinge --------8 3 8 Accessory list for this page. ! Rod adjuster Rod (2.5x100mm) - - - 12 Connecting rod head ----6 ---2 M3X35mm Screw ----4 M3X30mm Screw Rod (2.5x85mm) ---4 ----2 Rod adjuster M2X8mm Screw Horn ----6 ----2 - - - - 12 - - - 12 Rod (2.5x100mm) Horn ---2 M3X30mm Screw - - - - 12 Connecting rod head M4X35mm Screw ----6 ----6 ----2 M3X35mm Screw ---4 6 Install the nylon control horn and connect the linkage Rod (2.5x85mm) ---4 9 Assemble of the servo ----4 M3X30mm Screw - - - - 12 M3X30mm Screw ----2 M2X8mm Screw M4X35mm Screw - - - - 12 ---4 Install the nylon control horn and connect the linkage A 10 Epoxy the wheel wells to the holes Trim the holes if necessary 2 Assemble of the servo 50 7 C.A 4 B ! 5X45mm Axletree ----2 3X20mm Tp screw -----8 5.2mm Collar -----2 3X3mm screw -----2 4X4mm screw -----2 Rod adjuster -----1 2X8mm Horn screw -----1 2000mm Air line -----2 Make sure hings are mounted in the same line Rod adjuster ---4 Connecting rod head ----2 Retainer -----1 M2X8mm Screw ----4 Rod (1.8X80mm) -----1 M3X35mm Screw ----4 Pin hings A B M3X30mm Screw ----6 Rod (2.5x85mm) Epoxy pin hinges to elevator ----2 ----2 ----2 Pin hings M4X35mm Screw -----------6 ----2 ----2 11 13 Accessory list for this page. 14 Assemble of the landing gear Epoxy elevator hinges to horizontal tail A 5X45mm B Axletree -----2 3X20mm Tp screw -----8 5.2mm Collar -----2 !£¡Warning! 3X3mm screw -----2 Securely glue together ,if coming off during . You will lose control of your airplane which leads to accidents! 4X4mm screw -----2 12 15 Two wheel retract system Install the elevator servos M3X35mm Screw ----4 M3X30mm Screw Horn 2000mm Air line Please insure the sealing of the retract system before flight . Pleas notice the inner diameter for each side of the pressure reduction inlet. ----2 -----2 Rod adjuster -----1 Retainer 2X8mm Rod (1.8X80mm) screw -----1 Connecting rod head ----2 M4X35mm Screw ----2 -----1 Rod adjuster ---4 -----1 5 ----2 M2X8mm Screw ----4 ----2 Rod (2.5x85mm) ----2 18 Accessory list for this page. ! Install the tail wheel M3X16mm Cap screw Pin hings - - - - -4 4 Horn M4X45mm ----2 3X3mm Screw ----4 Connecting rod head ----2 3.2mm Nylon Collar ----1 ----1 3.2mm Metal Collar Screw ----3 -----1 ----3 Rod adjuster M2X8mm Rod -----1 3.2mm Nylon Collar 3.2mm Rocker M3X35mm ----2 3.2mm Rocker 3X3mm Screw ----4 ----3 M3X16mm Cap screw 4 Screw ------2 Screw ----2 Set Nut -------3 10mm tube ------2 8mm prapilionaceous Nut 3.2mm Metal Collar ----3 16 -----4 19 Epoxy pin hings to rudder Rudder . Connect the linkage rod to the horn Horn Pin hings ----2 ------4 Connecting rod head ----2 Make sure hings are mounted in the same line Rod adjuster ----2 Rod ------2 10mm tube ------2 M4X45mm Screw ----3 M3X35mm Screw ----3 M2X8mm A B Screw ----2 Set Nut -------3 20 Mount the main wing on the fuselage Install the rudder Tailing edge 8mm prapilionaceous Nut -----4 4mm 17 Rudder A B Warning! Securely glue together. If coming off during flights,you'll lose control of your airplane which leads to accidents! 6 ! 23 Accessory list for this page. Assembly of the engine Aluminium tube M4X10mm screw ------2 - - - - 16 Aluminium tube - - - - 16 3mm Blind Nut - - - - - - - - - 12 M3X20mm screw - - - - - - 12 21 A 24 Epoxy the horizontal tail to fuselage B Assembly of the engine A B M4X10mm screw ------2 10mm 3mm Blind Nut - - - - - - - - - 12 securely glue together,if coming off during flights, you'll lose control of your airplane which leads to accidents. 22 M3X20mm screw - - - - - - 12 Assemble horizontal tail,vertical tail, tail gear separately A A A 25 A Make sure to glue securely. If not properly glued,a failure in flight may occur Securely glue together, If coming off during flihts .you’ll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position. 7 Assembly of the engine 28 Assemble the servos and switch in the fuselage Accessory list for this page. ! Rod adjuster -----2 Aluminium tube -----2 2X8mm screw -----2 Rod ---2 M3X15mm screw ------5 3mm Washer ---------6 Rod adjuster -----2 26 Epoxy the wheel wells to the holes 29 Trim the holes if necessary Aluminium tube 2X8mm -----2 screw -----2 Rod -----2 Trim the surplus shaded portion away from the canopy After confirming the position(see front of fuel tank). Insert and tighten the screw. 3X20mm Screw ----1 27 30 Assemble of the landing gear Install the cowling Fuel tank M3X15mm screw ------5 3mm Washer ---------6 8 33 Adjustment. Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. AILERON Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. Side view 75mm 75mm AILERON Adjustment. Top view 85mm FLAP 32 Adjustment. 34 95mm 95mm 31 Centre of Gravity. Never fly before checking the Cg s required position. In order to obtain the CG specified ,reposition the receiver and battery. Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. 80mm 80mm 170-180mm ELEVATOR ! Warning! NEVER fly the model without well balancing. 35 Centre of Gravity. 9 CG