Download General Motors Lock Decoder Grooved Tweezer
Transcript
LOCKSMITHING TOOLS General Motors Lock Decoder This quality tool makes everyone a professional from the start. Decode all year General Motors sidebar locks without complete disassembly. This unique tool works when all others fail. Instructions included. Part No.: AIS 6 Grooved Tweezer Straight Blades For Easy Top Pin Loading Tubular Lock Saw Made to last. A–1’s rotary saw cuts away the shoulder over pins to allow them to be removed and lock opened. Since the pins remain intact, they can be measured to decode the lock in a situation such as a laundromat, where numerous locks are keyed alike. It will also open locks with ball bearings in the keyway, but should not be used on locks with dead pins. This saw will cut brass or steel 137 standard locks at low speed. Not recommended or guaranteed for over 1000 rpm. A–Pick Made of heat treated stainless steel, the A–Pick can open 137 standard tubular locks with mushroom pins and will pass all dead pins. In addition, once the lock is opened, the A–Pick can be quickly decoded using the decoder supplied. This is a precision instrument with built–in quality to do the job. Comes with easy–to–understand instructions. Part No.: AIS 20 Part No.: AIS 14 A-Pick Kit Cylinder Removal Tool A kit containing A–1’s #20 and #20X. Includes A–1 tubular key decoder Part No.: AIS 20-SET Specially grooved for pinning, these tweezers offer straight, parallel blades for ease of top pin loading. Optimum design for I/Core. Part No.: AIS 29 Tension Wrench “Feather Touch” Automotive Rocker Pick Set This cam action tool allows you to remove stubborn mortise cylinders. This heavy–duty tool automatically adjusts from 15/16" to 11/2" in diameter. Heat treated and plated. 8 Piece Part No.: AIS 16 Curved Shims The secret of picking some locks is a light turning pressure. This tool automatically adjusts to the proper tension. By using this wrench designed with a coil spring principle, any pressure can be applied, from a small fraction of an ounce to four ounces. 8 of A-1’s favorite rocker picks. Use for domestic and foreign automotive applications. Part No.: AIS 47 Part No.: AIS 11 Chrome plated, A-1 quality firm shims. Part No.: AIS 19 Shim Holder This tool holds curved shims firm, straight and without slippage to prevent cut fingers and make your job easier. Comes with 25 top quality shims. To use: Tap small end on hard surface; insert shim to desired length; press down on large end and shim is tight. Part No.: AIS 18 PHONE: 800–745–5450 • FAX: 800–876–5397 1 LOCKSMITHING TOOLS G.M. 10–Cut Pick Set Magnum Pick Gun Features easy tension adjustment. Three tips and tension wrench are included. This gun can be easily disassembled for maintenance. A 5-year warranty included. This set of tools will allow you to pick and decode G.M. 10–cut ignitions in minutes. Simply insert the special Tension Tool to apply sidebar pressure then pick the lock with your choice of 4 especially designed Rocker Picks. Once the lock is picked, use the Cylinder Release Tool to release the ignition from the Column. After removal, the plug can be decoded quickly and effortlessly using the Depth gauge. • Includes all tools required • Tension tools • 4 rocker picks with leather case • Depth Gauge • Cylinder release tool • Service manual • Lower shroud required on trucks only (tools included) Part No.: AIS 44 Master Locksmith Hammer So many locksmith jobs require a light weight hammer. A-1’s is manufactured specifically to meet your needs. This 2 oz. hammer features a head with one end brass, the other durable, non-marring plastic. Part No.: AIS 28 Ace Key Decoder Replacement Parts Decodes “Ace” keys quickly, easily, and accurately. Part No.: AIS 52 Get–A–Grip Puller Part No.: AIS 44 REPL This hex handled, spiral key puller offers a better way to Get–A–Grip. It features an extra long spiral and a hexagonal handle. Plug Spinner Part No.: AIS 30 Part No.: AIS PS2 Mega Grip Puller Ford 8–Cut Pick Set For Side Bar Ignitions Frequently it is almost impossible to pick a lock in the right direction, but easy to pick it backward. That’s when this tool is a must. With the lock picked in the wrong direction, simply wind the spinner 11/2 turns (in whichever direction necessary), set the trigger, insert the blade into the plug, release the trigger, and the plug is now picked in the right direction. Part No.: AIS 26 Similar to A-1’s automotive picks for General Motors, these tools are designed to professionally pick Ford ignitions without damaging the locks or bezel. This set includes a unique bezel removal tool, a jig with .070 drill bit for drilling the pilot hole, a special tension tool for disabling the side bar, and four rocker picks. Similar to the popular Get-A-Grip, but with an exceptionally large.074 Spiral. Great for use on many imported autos. Part No.: AIS 30B Get-A-Grip Set 2 each of A1’s popular Get-A-Grip and Mega Grip Key Pullers in 1 convenient set. Part No.: AIS 30-SET Part No.: AIS PS4 2 WHOLESALE BUILDERS HARDWARE & LOCKSMITHS SUPPLIES LOCKSMITHING TOOLS Broken Key Pullers Fighting Wedge Made of top quality American steel. Blades are locked in steel and fitted with a comfortable handle. A kit of three extractor types: .040 spiral, saw tooth, and hook. Pull popular key–in–knob cylinders in seconds! Snap cylinders out without disassembly of knobset or removal of interior knob. Use this tool to save a tremendous amount of time, especially on large re-keying jobs. Part No.: AIS 27 Vulcan Button Grabber Unique rubber loop grabs and holds buttons, without damage. A simple but effective car opener that holds most buttons, even straight ones Easily enters through door jam. Use strings for alignment. Great for Mercedes, BMW, Volvo Quickpull Fortified inflatable wedge can exert extreme pressure to widen the gap with your favorite car opening tools. Also use for Safes, window and door installations. Superior release valve. Part No. Part No.: AIS 43 Quickpull 2 Key Puller Set Part No.: AIS CO2 Similar to the original, this tool removes knobs for Schlage ‘F’ series. Using the additional tools included, replacement of the original knob and cylinder can be accomplished quickly and effortlessly, saving valuable time on the job. Knob can be removed from the exterior and replaced in just minutes. Part No. An assortment of extractors in a genuine leather case. A high quality broken key puller set includes 4 extractors: Hook, Standard Spiral, Large Spiral, Saw Tooth. Part No. Description AIS QP ----------Quickpull AIS QPBL -------Replacement blade for QP AIS QPRP-------Repair Kit for QP Description AIS QP2---------Quickpull 2 AIS QP2B -------Replacement blade for QP2 AIS QP2RP -----Repair Kit for QP2 Adjustable Tension Wrench Description AIS KP1 ---------Key Puller Set Designed for picking double–bitted locks, but also works for most paracentric keyways. Leaves keyway open for pick. Just right for auto locks with spring loaded dust covers. The spring steel fingers adjust to the desired width by sliding the adjusting collar. Part No.: AIS 24 PHONE: 800–745–5450 • FAX: 800–876–5397 3 LOCKSMITHING TOOLS Spinnakur Plug Spinner Capping Block Space age plug spinner. Made of durable materials, this tool will offer years of reliable service. Features spring mechanism, push button release, left or right rotation, streamlined design. Weighs only 21/4 oz. Fits in your shirt pocket or most pick kits. Part No.: AIS SP1 Waffle Tray A–1’s capping block has the added advantage of offering two tops, allowing you to cap Best, Eagle, KSP, Arrow and even the Falcon Style with the “slide” style spring cover. More than just a capping block, this tool is a complete and versatile workstation. No mobile shop should be without this time-saver. Part No.: AIS TB2 Dumping Block Make your workspace efficient. Especially useful space saver for the van. Keep springs, pins and plug neatly separated and in numbered pockets with this popular tool. Made from coated metal. It is small and stackable. Part No. AIS WT1 Ejector Punch Originally designed for use with “The Block”, this single ejector punch is suitable for most any I/Core. Part No. AIS TBIP With A–1’s Dumping Block, you have the added security of knowing that your customer’s security is maintained. Dump old cores to assure that no one can determine the control key code of your system. Also a big time-saver when re-keying, this tool will allow you to dump and hold the contents of dozens of cores. Part No.: AIS TB3 Pak-A-Punch™ Code Cutter Decoding Tool For I/C Core When a control key code must be found for an interchangeable core system, The Block offers a foolproof solution. Simply drive the pin stacks into The Block where a pin tray keeps them separated and in order. Superior to shimming or disassembly; all pin stacks are kept in their original array for decoding and replacement into the cylinder. Part No. AIS TB1 Model 3S is setup for Schlage/Primus. No additional attachments required. This machine can also punch automotive I/Core & Kwikset by ordering the appropriate accessories. Part No. AIS PAK3S 4 WHOLESALE BUILDERS HARDWARE & LOCKSMITHS SUPPLIES LOCKSMITHING TOOLS Cabinet Lock Installation Jig This jig is designed to install 2 styles of cabinet locks: • Cam locks using 7/8" cross-bore • I/Core Locks using 11/4" cross-bore Manufactured of aircraft grade aluminum alloy, and steel bushing. Both side of this jig are identical and include 1/8" graduated backset markings. The built-in level provides for easy and accurate setup. Part No.: AIS BUL-1 Bulls Eye Installation Tool for Cylindrical Locksets Use this tool when locating and drilling crossbores and latch holes when installing cylindrical locks. Uses conventional hole saws. Economically designed for locksmiths, this new tool is equipped to drill 11/2" and 21/8" cross bores and includes an automatic backset adjustment that requires no additional tools. Part No.: AIS BUL-2 Kelly -Klamp An innovative tool that is like a third hand for installing overhead magnets. Part No.: AIS K100 PHONE: 800–745–5450 • FAX: 800–876–5397 5