Download HCD-HP8V

HCD-HP8V
SERVICE MANUAL
E Model
Ver 1.0 2003.07
HCD-HP8V is the Amplifier, CD player, Tape
Deck and Tuner section in CMT-HP8V.
CD
Section
TAPE
Section
Model Name Using Similar Mechanism
NEW
CD Mechanism Type
CDM69BH-30BD62
Base Unit Name
BU-30BD62
Optical Pick-up Name
A-MAX.3
Model Name Using Similar Mechanism
HCD-EP515
Tape Transport Mechanism Type
CMAL1Z234A
SPECIFICATIONS
Main unit
CD player section
Amplifier section
System
The following measured at AC 120, 127, 220, 240 V
50/60 Hz
DIN power output (rated): 60 + 60 watts (6 ohms at 1
kHz, DIN)
Continuous RMS power output (reference):
60 + 60 watts (6 ohms at 1
kHz, 10% THD)
Inputs
MD IN (phono jacks):
MIC (phone jack):
Sensitivity 250 mV,
impedance 47 kilohms
Sensitivity 1 mV,
impedance 10 kilohms
Outputs
PHONES (stereo minijack):
Accepts headphones of 8
ohms or more
MD OUT (phono jack): Impedance 1 kilohm
VIDEO OUT (phono jack):
Max. output level 1Vp-p,
unbalanced, Sync
negative, load impedance
75 ohms
SPEAKER:
Accepts impedance of 6 to
16 ohms.
Tuner section
Laser
Frequency response
Wavelength
Signal-to-noise ratio
Dynamic range
Video color system format
Compact disc and digital
audio system
Semiconductor laser
(λ=780 nm)
Emission duration:
continuous
2 Hz – 20 kHz (±0.5 dB)
780 – 790 nm
More than 90 dB
More than 90 dB
NTSC, PAL
Tape deck section
Recording system
Frequency response
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
AM tuner section
Tuning range
Middle Eastern model:
Other models:
4-track 2-channel, stereo
50 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassettes
Antenna
Antenna terminals
Intermediate frequency
87.5 – 108.0 MHz
FM lead antenna
75 ohms unbalanced
10.7 MHz
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
AM loop antenna
External antenna terminal
450 kHz
MICRO HI-FI COMPONENT SYSTEM
9-877-476-01
Sony Corporation
2003G1678-1
© 2003.07
Home Audio Company
Published by Sony Engineering Corporation
HCD-HP8V
General
Power requirements
Saudi Arabian model:
Other models:
120 – 127/220 or 230 – 240
V AC, 50/60 Hz
Adjustable with voltage
selector
120 V, 220 V or 230 – 240
V AC, 50/60 Hz
Adjustable with voltage
selector
Power consumption:
100 watts
Dimensions (w/h/d)
Approx. 199 × 252 × 400
mm
Mass
Approx. 7.5 kg
Supplied accessories:
Remote commander (1)
Batteries (2)
AM loop antenna (1)
FM lead antenna (1)
Speaker pads (8)
Video cable (1)
Design and specifications are subject to change
without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
2
HCD-HP8V
TABLE OF CONTENTS
1. SERVICING NOTES ······················································· 4
6. MECHANICAL ADJUSTMENTS ····························· 24
2. GENERAL ·········································································· 6
7. ELECTRICAL ADJUSTMENTS ······························· 25
3. DISASSEMBLY
8. DIAGRAMS ······································································ 28
3-1. Case (Side-L)(Side-R),
Tape Mechanism Deck (CMAL1Z234A) ······················ 9
3-2. Front Panel Section ······················································· 9
3-3. Panel Board ································································· 10
3-4. Back Panel Section ······················································ 10
3-5. MAIN Board ······························································· 11
3-6. PWR AMP Board, Power Transformer ······················· 11
3-7. CD Mechanism Deck (CDM69BH-30BD62) ············· 12
3-8. JACK Board, VMP Board ··········································· 12
3-9. Base Unit Section ························································ 13
3-10. Base Unit (BU-30BD62) ············································· 13
3-11. BD Board ····································································· 14
3-12. SW Board, Bracket (Top) Assy ··································· 15
3-13. CONNECTOR Board ·················································· 15
3-14. Motor (Stocker) Assy (Stocker)(M761) ······················ 16
3-15. Motor (Roller) Assy (Roller)(M781) ··························· 16
3-16. Motor (Mode) Assy (Mode)(M771) ···························· 17
3-17. Rubber Roller (Slider) Assy ········································ 17
3-18. Timing Belt (Front/Rear) ············································· 18
3-19. Cam (Gear) ·································································· 18
3-20. SENSOR Board ··························································· 19
4. ASSEMBLY
4-1. How to Install the Cam (Eject Lock) ···························· 20
4-2. How to Install the Cam (GEAR) ··································· 20
4-3. How to Install the Gear (MODE C) ······························ 21
4-4. How to Install the Gear (MODE CAM) ······················· 21
4-5. How to Install the Rotary Encoder (S702),
Gear (STOCKER COMMUNICATION) ····················· 22
4-6. How to Install the Stocker Assy ···································· 22
5. TEST MODE ···································································· 23
8-1. Block Diagram — CD SERVO Section — ················· 30
— AUDIO/VIDEO Section — ···································· 31
— MAIN Section — ··················································· 32
8-2. Printed Wiring Boards — BD Section — ··················· 33
8-3. Schematic Diagram — BD Section — ························ 34
8-4. Printed Wiring Boards — VMP Section (1/2) — ········ 35
8-5. Printed Wiring Boards — VMP Section (2/2) — ········ 36
8-6. Schematic Diagram — VMP Section (1/2) — ············ 37
8-7. Schematic Diagram — VMP Section (2/2) — ············ 38
8-8. Printed Wiring Boards — Changer Section — ··········· 39
8-9. Schematic Diagram — Changer Section — ················ 40
8-10. Printed Wiring Boards — Main Section — ················· 41
8-11. Schematic Diagram — Main Section — ····················· 42
8-12. Printed Wiring Boards — Front Section — ················ 43
8-13. Schematic Diagram — Front Section — ····················· 44
8-14. Printed Wiring Boards
— PWR AMP/Power Section — ································· 45
8-15. Schematic Diagram
— PWR AMP/Power Section — ································· 46
8-16. IC Block Diagrams ······················································ 47
8-17. IC Pin Function Description ········································ 50
9. EXPLODED VIEWS
9-1. Case, Top Panel Section ·············································· 57
9-2. Front Panel Section ····················································· 58
9-3. Chassis Section-1 ························································ 59
9-4. Chassis Section-2 ························································ 60
9-5. CD Mechanism Section-1 (CDM69BH-30BD62) ······ 61
9-6. CD Mechanism Section-2 (CDM69BH-30BD62) ······ 62
9-7. CD Mechanism Section-3 (CDM69BH-30BD62) ······ 63
9-8. CD Mechanism Section-4 (CDM69BH-30BD62) ······ 64
9-9. CD Mechanism Section-5 (CDM69BH-30BD62) ······ 65
9-10. CD Mechanism Section-6 (CDM69BH-30BD62) ······ 66
9-11. Base Unit Section (BU-30BD62) ································ 67
10.ELECTRICAL PARTS LIST ······································· 68
3
HCD-HP8V
SECTION 1
SERVICING NOTES
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
This appliance is classified as a CLASS 1 LASER product.
This label is located on the rear exterior.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
4
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveforms is output three times.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 ˚C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C .
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HCD-HP8V
Service Position of the Tape Cassette Mechanism Deck
Service Position of the CD Mechanism Deck
5
HCD-HP8V
SECTION 2
GENERAL
This section is extracted
from instruction manual.
List of button locations and reference pages
How to use this page
Illustration number
r
Use this page to find the location of buttons and other
parts of the system that are mentioned in the text.
TAPE A/B 5 (18, 19)
R
Name of button/part
R
Reference page
Main unit
BUTTON DESCRIPTIONS
ALPHABETICAL ORDER
6
A–M
P–Z
CD SYNC 9 (18)
DIMMER ws (25)
DISC 1 – 5 qs (10, 13, 32)
Disc slot qf
DISPLAY 6 (24, 25, 32)
Display window 3
ECHO LEVEL qg (21)
FUNCTION wd (9, 11, 13, 16, 18,
19, 28)
GROOVE w; (20)
MIC jack qj
MIC LEVEL qh (21)
PHONES jack qd
PLAY MODE 7 (9, 13, 18, 19,
23)
PRESET EQ wa (20)
PRESET/ALBUM +/– wf (10,
13, 15, 16)
REC PAUSE/START 0 (18, 19,
21)
Remote sensor 2
REPEAT 8 (12)
Tape deck 4
TUNER/BAND 5 (15, 16)
TUNING +/– qa (15, 16)
VOLUME ql (22)
?/1 (power) 1 (7, 8, 16, 22, 23,
32)
m/M (rewind/fast forward)
qa (10, 18)
./> (go back/go forward)
qa (7, 10, 12, 13, 18)
x (stop) 5 (10, 11, 16, 18, 19,
21, 23, 32)
X (pause) 5 (7, 10, 18)
CD N (play) 5 (10, 11, 13, 14,
37)
TAPE nN (play) 5 (18, 19,
23)
DISC 1 Z – DISC 5 Z (eject) qk
(9, 10)
HCD-HP8V
Remote control
ALPHABETICAL ORDER
BUTTON DESCRIPTIONS
A–N
O–Z
ALBUM +/– wh (10, 13)
CD es (9, 11, 13, 16, 18, 19)
CLEAR 9 (13, 14)
CLOCK/TIMER SELECT 2
(23, 24)
CLOCK/TIMER SET 3 (8, 22,
23)
DISPLAY 8 (24, 25, 32)
D. SKIP qa (10, 13)
EFFECT ON/OFF wd (20)
ENTER wf (8, 13, 15, 22, 23)
GAME (MD)1) 6 (19, 28)
GROOVE wa (20)
KARAOKE/MPX qj (21)
KEY CONTROL #/2 qk (21)
NEXT wk (11, 14)
Numeric buttons wl (10, 11, 13,
14)
ON SCREEN qs (26)
PLAY MODE e; (9, 13, 18, 19,
23)
PRESET EQ wg (20)
PRESET +/– wk (15, 16)
PREV wk (11, 14)
REPEAT/FM MODE ea (12, 17)
SLEEP 1 (22)
SPECIAL MENU q; (14)
SURROUND ql (20)
TAPE A/B2) 5 (18, 19)
TUNER BAND ed (15, 16, 19)
TUNER MEMORY 7 (15)
TUNING +/– wj (15, 16)
VOL +/– w; (22)
?/1 (power) 4 (7, 8, 16, 22, 23,
32)
m/M (rewind/fast forward)
wj (10, 18)
./> (go back/go forward)
wk (7, 10, 12, 13, 18)
x (stop) qg (10, 11, 16, 18, 19,
21, 23, 32)
X (pause) qh (7, 10, 18)
N (play) qd (10, 11, 13, 14, 18,
19, 23, 37)
M/m/</, (cursor) ws (8, 22,
23)
RETURN O qf (11)
1)
This button is used to switch
to MD function.
2)
This button is used to switch
to TAPE function.
1 2 3 4
ed
5
6
es
7
ea
e;
8
9
wl
q;
qa
qs
qd
qf
qg
qh
qj
wk
wj
wh
V
ws
ql
b
B
wf
wd
Setting the clock
qk
wg
Use buttons on the remote for the operation.
w;
v
wa
1
2
3
4
5
6
Press ?/1 to turn on the system.
Press CLOCK/TIMER SET.
Press M/m repeatedly to set the hour.
Press ,.
Press M/m repeatedly to set the
minute.
Press ENTER.
The clock starts working.
To adjust the clock
1
2
3
Press CLOCK/TIMER SET.
Press M/m to select “CLOCK SET”, then
press ENTER.
Do the same procedures as step 3 to 6
above.
Notes
• The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
• You cannot set the clock in Power Saving Mode.
7
HCD-HP8V
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
SET
CASE (SIDE-L) (SIDE-R),
TAPE MECHANISM DECK
(CMAL1Z234A))
BACK PANEL SECTION
MAIN BOARD
FRONT PANEL SECTION
PANEL BOARD
PWR AMP BOARD,
POWER TRANSFORMER
CD MECHANISM DECK
(CDM69BH-30BD62)
MOTOR (STOCKER) ASSY
(STOCKER) (M761)
BASE UNIT SECTION
SW BOARD,
BRACKET (TOP) ASSY
JACK BOARD,
VMP BOARD
CONNECTOR BOARD
BASE UNIT
(BU-30BD62)
RUBBER ROLLER
(SLIDER) ASSY
BD BOARD
MOTOR (ROLLER)
ASSY (ROLLER) (M781)
MOTOR (MODE)
ASSY (MODE) (M771)
TIMING BELT
(FRONT/REAR)
CAM (GEAR)
SENSOR BOARD
8
HCD-HP8V
Note: Follow the disassembly procedure in the numerical order given.
3-1. Case (Side-L)(Side-R), Tape Mechanism Deck (CMAL1Z234A)
7 two screws
(BVTP3× 16)
8 top panel section
4 four screws
(case3 TP2)
5 two screws
(BVTP3× 16)
qd tape mechanism deck
(CMAL1Z234A)
qs shield plate (case)
9 connector
(6p)
qa four screws
(BVTP2.6× 8)
q; wire (flat type) 8p
2 two screws
(BVTP3× 16)
6 case (side-L)
1 four screws
(case3 TP2)
3 case (side-R)
3-2. Front Panel Section
2 screw
(BVTP3× 8)
4 connector
(CN405)
3 wire (flat type)
9p (CN303)
8 front panel section
5 wire (flat type)
37p (CN402)
1 screw
(BVTP3× 8)
6 connector
(CN305)
7 two screws
(BVTP3× 8)
9
HCD-HP8V
3-3. Panel Board
4 PANEL board
3 six claws
2 ten screws
(BVTP2.6× 8)
1 knob (VOL)
3-4. Back Panel Section
6 connector
(CN908)
8 back panel section
4 connector
(CN503)
2 three screws
(BVTP3× 10)
3 two screws
(BVTP3× 8)
5 connector
(CN905)
7 connector
(CN904)
10
1 wire (flat type)
11p (CN101)
HCD-HP8V
3-5. MAIN Board
5 wire (flat type)
9p (CN303)
4 wire (flat type)
37p (CN402)
3 connector
(CN404)
1 connector
(CN907)
9 MAIN board
2 two screws
(BVTP3× 8)
8 connector
(CN305)
7 wire (flat type)
27p (CN302)
6 wire (flat type)
19p (CN301)
3-6. PWR AMP Board, Power Transformer
5 four screws
(BVTT4× 8)
1 connector
(CN902)
2 screw
(BVTP3× 8)
3 four screws
(BVTP3× 8)
6 power transformer
4 PWR AMP board
11
HCD-HP8V
3-7. CD Mechanism Deck (CDM69BH-30BD62)
1 two screws
(BVTP3× 8)
3 blacket (TR)
2 two screws
(BVTP3× 8)
5 four screws
(BVTP3 × 8)
7 CD mechanism deck
(CDM69BH-30BD62)
6 wire (flat type)
28p (CN101)
4 wire (flat type)
19p (CN201)
3-8. JACK Board, VMP Board
4 two screws
(BVTP3 × 8)
1 connector
(CN301)
7 VMP board
6 support spacer (VMP)
5
3 JACK board
2 screw
(BVTP3 × 8)
12
HCD-HP8V
3-9. Base Unit Section
2 screw (DIA. 12)
3 boss
1 floating screw (+PTPWHM2.6)
4 boss
7 base unit section
3-10.
5 boss
6 boss
Base Unit (BU-30BD62)
q; base unit (BU-30BD62)
4 floating screw
(+PTPWHM2.6 × 6)
8 insulator (BU30)
1 floating screw
(+PTPWHM2.6 × 6)
3 floating screw
(+PTPWHM2.6 × 6)
9 insulator (BU30)
7 insulator (BU30)
5
2 floating screw
(+PTPWHM2.6 × 6)
6 insulator (BU30)
13
HCD-HP8V
3-11.
BD Board
2 wire (flat type) (16 core)
1 Remove the solder
(four portions).
3 BD board
14
HCD-HP8V
3-12.
SW Board, Bracket (Top) Assy
4 SW (3) board
3 SW (2) board
5 SW (4) board
1 four screws
(BTP2.6 × 6)
6 six screws
(BVTP2.6 × 8)
2 SW (1) board
7 bracket (top) assy
3-13.
CONNECTOR Board
– bottom view –
CONNECTOR board
4 connector
(CN710) 3
5 connector
(CN702)
6 connector
(CN703)
2 four screws
(BVTP2.6 × 8)
7 CONNECTOR board
1 Remove five solders.
15
HCD-HP8V
3-14.
Motor (Stocker) Assy (Stocker)(M761)
3 two screws
(BVTP2.6 × 8)
4
2 Remove two solders
5 STOCKER MOTOR board
6 motor (stocker) assy
(stocker) (M761)
1 belt (mode)
3-15.
Motor (Roller) Assy (Roller)(M781)
3 two screws
2 Remove two solders.
4 ROLLER MOTOR board
5 motor (roller) assy
(roller)(M781)
1 belt (roller V)
16
HCD-HP8V
3-16.
Motor (Mode) Assy (Mode)(M771)
3 two screws
(BVTP2.6 × 8)
1 Remove five solders
of rotary encoder.
4 MODE MOTOR board
6 motor (mode) assy
(mode) (M771)
MODE MOTOR
board
2 Remove two solders
of motor (M771)
5 belt (mode V)
3-17.
Rubber Roller (Slider) Assy
8 step screw
0 rubber roller
(slider 1) assy
9 tension
spring
(slider 2)
5 step screw
1 step screw
6 tension spring
(base slider 4)
2 rubber roller
(slider S) assy
qa rubber roller
(slider 2) assy
3 tension spring
(base slider 5)
qs step screw
7 rubber roller
(slider 1) assy
qd rubber roller
(slider 4) assy
qf screw
(BVTP2.6 × 8)
4 rubber roller
(slider 5) assy
qg sub chassis
17
HCD-HP8V
3-18.
Timing Belt (Front/Rear)
3 slider (mode cam) assy
7 two gears (center)
When install three timing belts,
its pass under each claws.
8 timing belt (rear)
timing belt
(rear)
5 two gears
(center)
9 timing belt (rear)
claw
6 timing belt
(front)
claw
timing belt
(rear)
claw
claw
4 gear
(timing)
timing belt (front)
2 gear (mode cam)
: Note
Note: Refer to assembly (Section 4)
1 screw
(PTPWH2.6 × 8)
3-19.
Cam (Gear)
qf cam (gear)
: Note
6 gear (mode 5)
qd screw
5 screw (PTPWH2.6 × 8)
4 gear (mode 5)
qs gear(mode cam)
3 screw (PTPWH2.6 × 8)
qa screw
(PTPWH2.6 × 8)
2 pulley
(mode deceleration)
0 gear
(mode C)
:Note
Note: Refer to assembly
(Section 4).
18
9 screw
(PTPWH2.6 × 8)
1 screw(PTPWH2.6 × 8)
8 gear (mode D)
7 screw (PTPWH2.6 × 8)
HCD-HP8V
3-20.
SENSOR Board
ql harness
qk claw
q; cam (eject lock)
: Note
9 screw
(PTPWH2.6 × 8)
qh two claws
qd gear (eject lock)
qs cam (BU U/D)
8 shaft
(shutter)
7 compression spring
(shutter)
wa SENSOR board
w; screw
(BVTP2.6 × 8)
qg screw
(PTPWH2.6 × 8)
6 gear (mode A)
5 base (shutter) block
qa screw
(PTPWH2.6 × 8) 3 screw
(BVTP2.6 × 8)
1 screw
(PTPWH2.6 × 8)
qj rotary encoder
(S771)
qf gear
(mode B)
Note: Refer to assembly (Section 4).
4 two screws
(BVTP2.6 × 8)
2 lever shutter (A)
19
HCD-HP8V
SECTION 4
ASSEMBLY
• This set can be assembled in the order shown below.
4-1.
How to Install the Cam (Eject Lock)
1 Rotate the cam (BU U/D) fully in the direction of arrow.
2 Engage the gear (eject lock) and the gear of the cam (eject lock)
aligning the mark with the center of the gear (eject lock).
cam (BU U/D)
mark
gear (eject lock)
cam (eject lock)
– bottom view • front –
4-2.
How to Install the Cam (Gear)
1 Check that the cam (BU U/D) can not be rotated in the direction of arrow.
2 Align the mark on the cam (gear) with the boss as shown in the figure
and install the cam (gear).
cam (gear)
boss
cam (BU U/D)
mark
– bottom view • front –
20
HCD-HP8V
4-3.
How to Install the Gear (Mode C)
1 Align the mark on the rotary encoder (S771) with the projection of the assy.
2 Check that the cam (BU U/D) can not be rotated in the direction of arrow.
3 Install the gear (mode C)
rotary encoder
(S771)
cam (BU U/D)
gear (mode C)
mark
chassis
projection
– bottom view • front –
4-4.
How to Install the Gear (Mode Cam)
1 Slide the shaft in the direction of arrow.
2 Align mark A on the gear (mode cam) with mark B on the slider (mode cam) assy,
then install the gear (mode cam).
3 Check that mark C on the gear (mode cam) is in alignment with mark D on the cam (gear).
shaft
mark A
slider (mode cam) assy
gear (mode cam)
mark D
mark B
mark C
cam (gear)
– bottom view • front –
21
HCD-HP8V
4-5.
How to Install the Rotary Encoder (S702), Gear (Stocker Communication)
4 gear
(stocker communication)
5 screw
(PTPWH2.6 × 8)
3 screw
(PWH2 × 6)
Engage the rotary encoder (S702)
and the gear (stocker communication)
as shown below in the figure.
7 two screws
(PTPWH2.6 × 8)
1 rotary encoder
(S702)
6 two gears
(stocker communication)
rotary encoder
(S702)
2 five solders
gear
(stocker
communication)
CONNECTOR board
– rear –
4-6.
How to Install the Stocker Assy
boss
Install the stocker assy
fitting three bosses into the
each groove of cam (stocker
U/D) then fix by rotating
the cams in the direction
of arrow.
3 three screws
(PTPWH2.6 × 8)
2 three cams
(stocker U/D)
boss
cam
(stocker U/D)
To install three cams
(stocker U/D), align each groove
of the cam (stocker U/D)
with each f mark on the
chassis as shown in the figure.
rotary encoder
(S702)
hole
screw
1 Position the hole on the gear
(stocker communication) on the
screw of the rotary encoder (S702).
gear
(stocker communication)
– rear –
22
HCD-HP8V
SECTION 5
TEST MODE
[AM Channel Step 9 kHz/10kHz Selection Mode]
[Panel Test Mode]
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Set the function to AM.
2. Press the ?/1 button to turn off the main power.
3. While depressing the TUNER/BAND button, press the ?/1
button to turn on the main power.
4. Either the message “MW 9k STEP” or “MW10k STEP”
appears, and thus the channel step is changed over.
* All fluorescent segments, LEDs, keys, volume and headphone
detection are tested.
Procedure:
1. Press the ?/1 button to turn the set on.
2. To enter the test mode, press three buttons DISPLAY , x and
DISC 3 simultaneously. All segments and LEDs are turned
on.
3. Press the x and PRESET EQ buttons simultaneously. In this
key code display mode, the fluorescent indicator displays “KEY
0 0 0”. Each time a button is pressed, the key code is displayed.
4. Press the x and PRESET EQ buttons simultaneously. In this
key count mode, the fluorescent indicator displays “KEYCNT
0 1”. Each time a button is pressed, “KEYCNT 0 X” value
increases. However, once a button is pressed, it is no longer
taken into account.
5. Press the x and PRESET EQ buttons simultaneously. When
a headphone jack is not inserted, “ H_P RELEASE” is
displayed. When a headphone jack is inserted, “ H_P IN” is
displayed.
6. Press the x and PRESET EQ buttons simultaneously. When
the VOLUME knob is not rotated, “VOLUME FLAT” is
displayed. The message “VOLUME UP” is displayed, when
the VOLUME knob is rotated clockwise. The message
“VOLUME DOWN” is displayed, when the VOLUME knob
is rotated counterclockwise.
7. To exit from this mode, press three buttons DISPLAY , x
and DISC 3 simultaneously.
[CD Ship Mode]
* This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the ?/1 button to turn the set on.
2. Press the N (CD) button and the ?/1 button simultaneously.
3. After the message “STANDBY” blinks, “LOCK” is displayed
on the fluorescent indicator tube, and the CD ship mode is set.
[Disc Tray Lock]
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure:
1. Press the ?/1 button to turn the set on.
2. Press two buttons of x and Z (DISC 1) simultaneously for
five seconds.
3. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure:
1. Press two buttons of x and Z (DISC 1) simultaneously for
five seconds again.
2. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note : When “LOCKED” is displayed, the tray lock is not released
by turning power on/off with the ?/1 button.
[Cold Reset]
* The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the
set to the customer.
Procedure:
1. Press three buttons DISPLAY , x and DISC 1
simultaneously.
2. The fluorescent indicator tube displays the message “COLD
RESET” and the set is reset.
[Version and Destination Display Mode]
* The version or destination is displayed.
Procedure:
1. Press the ?/1 button to turn the set on.
2. To enter the test mode, press the three buttons DISPLAY , x
and DISC 2 simultaneously.
3. The model and destination is displayed. Example : “HPVCD
ASIA3”
4. Press the x and PRESET EQ buttons simultaneously.
5. The version is displayed. Example : “V1.03:2003:02.20”
6. To exit from this mode, press the three buttons DISPLAY , x
and DISC 2 simultaneously, or press the ?/1 button to turn
the set off.
[MC Test Mode]
* This mode is used to check the function of the amplifier.
Procedure:
1. Press the ?/1 button to turn the set on.
2. To enter the test mode, press the three buttons DISPLAY , x
and DISC 4 simultaneously.
3. The message “VOLUME MIN”, “VOLUME 16” or
“VOLUME MAX” is displayed , when turning the VOLUME
knob clockwise or conterclockwise.
4. Each time the DIMMER button is pressed, the message “GEQ
MAX” or “GEQ MIN” is displayed. The function of the
equalizer is set to maximum or minimum.
5. The message “GEQ FLAT” is displayed, when pressing the
PRESET EQ button. The function of the equalizer is set to
flat.
6. Each time the GROOVE button is pressed, the message “VACS
OFF” or “VACS ON” is displayed.
7. Automatic recording/playback : Press the REC button when a
tape is inserted, recording is started and the input source
function is selected to “MD” automatically.
8. When the . button is pressed, tape is rewound , stops at
around the record-starting position and playback is started
automatically.
9. To exit from this mode, press the ?/1 button to turn the set
off.
23
HCD-HP8V
SECTION 6
MECHANICAL ADJUSTMENTS
[AMP Test Mode]
• TAPE MECHANISM DECK SECTION
Procedure:
1 Press the ?/1 button to turn the set on.
2. To enter the test mode, press the three buttons x ,
PRESET EQ and DISC 4 simultaneously.
3. The message “AMP TEST IN” is displayed.
4. Press the x and PRESET EQ buttons simultaneously. The
VACS status and IC parameters are displayed. Example : “D:
S: +4. 0. +2”
5. DBFB ON/OFF Function : Press the GROOVE button, “DBFB
ON” or “DBFB OFF” is displayed.
6. SURROUND ON/OFF Function : Press the PRESET EQ
button, “SURROUND ON” or “SURROUND OFF” is
displayed.
7. To exit from this mode, press three buttons x , PRESET EQ
and DISC 4 simultaneously.
Note: Perform the Cold Reset to initialize the equalizer parameters.
Precaution
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads
pinch rollers
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head
demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
Mode
Torque meter
[CD Service Mode]
* This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pickup.
Procedure:
1. Press ?/1 button to turn the set on.
2. Set the function to CD.
3. Press three buttons DISPLAY , x and DISC 5
simultaneously.
4. The MPEG AV TEST mode is selected.
5. When the DIMMER buttons is depressed, the CD service
mode is activated.
6. Press > button to move the pickup to outside track, or
press . button to inside track.
7. To exit from this mode, perform as follows:
1) Move the pickup to the most inside track.
2) Perform the Cold Reset.
Note: Do not run the sled motor excessively, otherwise the gear can
be chipped.
24
FWD
CQ-102C
FWD
back tension
CQ-102C
REV
CQ-102RC
REV
back tension
CQ-102RC
FF/REV
CQ-201B
FWD tension
CQ-403A
REV tension
CQ-403R
Meter reading
2.94 – 7.84 mN • m
(30 to 79 g • cm)
(0.42 – 1.11 oz • inch)
0.15 – 0.6 mN • m
2 to 6 g • cm
(0.03 – 0.08 oz • inch)
2.94 – 7.84 mN • m
(30 to 79 g • cm)
(0.42 – 1.11 oz • inch)
0.15 – 0.6 mN • m
2 to 6 g • cm
(0.03 – 0.08 oz • inch)
6.86 – 17.64 mN • m
(70 to 179 g • cm)
(0.98 – 2.49 oz • inch)
9.8 mN • m more
(100 • cm or more)
(1.4 oz • inch or more)
9.8 mN • m more
(100 • cm or more)
(1.4 oz • inch or more)
HCD-HP8V
SECTION 7
ELECTRICAL ADJUSTMENTS
DECK SECTION
3.
0 dB=0.775 V
Note: Confirm each contents of this section first of all. If the results are
not satisfied, do the adjustment.
1.
2.
3.
4.
5.
6.
7.
Mode: Playback
PWR AMP board
SPEAKER terminals (JK501)
L-CH
oscilloscope
test tape
P-4-A63J
(10 kHz, –10 dB)
L-CH
Demagnetize the record/playback head with a head
demagnetizer.
Do not use a magnetized screwdriver for the adjustments.
After the adjustments, apply suitable locking compound to the
parts adjust.
The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
The adjustments should be performed in the order given in this
service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit
adjustment.)
The adjustments should be performed for both L-CH and RCH.
Switches and controls should be set as follows unless otherwise
specified.
V
set
H
R-CH
R-CH
waveform of oscilloscope
in phase 45 °
good
90 ° 135 ° 180 °
wrong
• Test Tape
Tape
Signal
Used for
P-4-A63J
10 kHz, –10 dB
Azimuth Adjustment
Record/Playback Head Azimuth Adjustment
Procedure:
1. Mode: Playback
test tape
P-4-A63J
(10 kHz, –10 dB)
2.
Repeat step 1 to 3 in playback (REV) mode.
After the adjustments, apply suitable locking compound to the
pats adjusted.
Adjustment Location : Record/Playback/Erase Head
PWR AMP board
SPEAKER terminals (JK501)
L-CH, R-CH
level meter
set
4.
5.
adjustment screw
+
–
Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
within
1 dB
L-CH
peak
within
1 dB
Output
level
Screw
position
R-CH
peak
L-CH
peak
R-CH
peak
Screw
position
25
HCD-HP8V
Note: Clear RF signal waveform means that the shape “ ◊ ” can be clearly
distinguished at the center of the waveform.
CD SECTION
Note:
1. CD Block is basically designed to operate without adjustment. Therefore,
check each item in order given.
2. Use LUV-P01 (Part No. 4-999-032-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10MΩ impedance.
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specified value with the following checks.
RF signal waveform
VOLT/DIV : 200mV
TIME/DIV : 500ns
level : 0.75 ±0.1Vp-p (RFDC)
1.05 ±0.3Vp-p (RFAC)
S-CURVE CHECK
oscilloscope
TRAVERSE LEVEL CHECK
BD board
TP68 (FE)
TP73 (DVC)
+
–
oscilloscope
BD board
Procedure :
1. Connect an oscilloscope to TP68 (FE) and TP73 (DVC) on the
BD board.
2. Turn the power ON.
3. Load a disc (LUV-P01) and actuate the focus search. (In
consequence of open and close the disc tray, actuate the focus
search)
4. Confirm that the oscilloscope waveform (S-curve) is
symmetrical between A and B. And confirm peak to peak level
within 2 ± 0.5 Vp-p.
TP70 (TE)
TP73 (DVC)
+
–
Procedure :
1. Connect an oscilloscope to TP70 (TE) and TP73 (DVC) on the
BD board.
2. Turn the power ON.
3. Load a disc (LUV-P01) and playback the number nine track.
4. Press the CD N button. (Becomes the 1 track jump mode.)
5. Confirm that the level B and A (DC voltage) on the oscilloscope
waveform.
S-curve waveform
symmetry
1 track jump waveform
center of
waveform
A
B
within 2 ±0.5Vp-p
A (DC voltage)
B
DVC
Note: • Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the
brightness to obtain best waveform.
level=1.2 ±0.55Vp-p symmetry
Connecting Location:
– BD BOARD (Conductor Side) –
RF LEVEL CHECK
oscilloscope
BD board
TP71 (RFDC)
TP72 (RFAC)
TP73 (DVC)
+
–
Procedure :
1. Connect an oscilloscope CH1 to TP71 (RFDC), CH2 to TP72
(RFAC) and TP73 (DVC) on the BD board.
2. Turn the power ON.
3. Load a disc (LUV-P01) and playback the number nine track.
4. Confirm that oscilloscope waveform is clear and check if RF
signal level is correct or not.
26
TP70
(TE)
TP68
(FE)
TP71
(RFDC)
TP72
(RFAC)
TP73
(DVC)
HCD-HP8V
VIDEO SECTION
– VMP BOARD (Component Side) –
Video Level Check
(Audio Level/Video Clock/Audio Servo Clock Check)
TP308
(V-OUT)
oscilloscope
VMP board
TP308 (V-OUT)
VMP board
TP415 (L-OUT)
TP413 (R-OUT)
+
–
TP70
(54 MHz)
level meter
+
–
TP182
(4.2336 MHz)
VMP board
TP70 (54 MHz)
TP182 (4.2336 MHz)
frequency counter
+
–
TP415
(L-OUT)
TP413
(R-OUT)
Procedure :
1. Connect an oscilloscope to TP308 (V-OUT) on the VMP board.
2. Connect a level meter to TP415 (L-OUT) and TP413 (R-OUT)
on the VMP board.
3. Connect a frequency counter to TP70 (54 MHz) and TP182
(4.2336 MHz) on the VMP board.
4. Turn the power ON.
5. Set a test disc (HLV-402 (Part No. 8-909-870-00))
6. Press three buttons [DISPLAY], x and [DISC5] simultaneously.
7. Press the [DIMMER] button. The message “MPEG AV TEST”
is displayed on the fluorescent indicator. Color bar signal outputs
and sine-wave (1 kHz 0dB) appears.
8. Confirm that the signal at TP308 (V-PUT) on the VMP board is
0.714 ± 0.05 Vp-p.
Note: TP308 (V-OUT) on the VMP board must be teminated by 75 Ω.
0.714 ± 0.05 Vp-p
9. Confirm that the value of level meter is 2.5 ± 2.0 dBs.
10. Confirm that the value of frequency counter is 54 MHz ± 400
Hz.
11. Confirm that the value of frequency counter is 4,2336 MHz.
12. To exit from this mode, Press three buttons [DISPLAY], x and
[DISC1] simultaneously.
27
HCD-HP8V
SECTION 8
DIAGRAMS
• Circuit Boards Location
SUB TRANS board
SENSOR (FAN) board
PWR TRANS board
PWR AMP board
MAIN board
PANEL board
STOCKER MOTOR board
ST ENCODER board
JACK board
ROLLER MOTOR board
SW (4) board
VMP board
SW (3) board
SW (2) board
SW (1) board
CONNECTOR board
BD board
SENSOR board
28
MODE MOTOR board
HCD-HP8V
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
: internal component.
•
• 2 : nonflammable resistor.
• 1 : fusible resistor.
• C : panel designation.
• Waveforms
– BD Board –
For printed wiring boards.
Note:
• X
• Y
f
•
•
: parts extracted from the component side.
: parts extracted from the conductor side.
: internal component.
: Pattern from the side which enables seeing.
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
1 IC103 qg (RFAC)
– PANEL Board –
– VMP Board –
8 IC505 <zb/ (XTAO)
5 IC601 qd (XT2)
(CD Play Mode)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
1.05 ± 0.3 Vp-p
200 mV/DIV, 400 ns/DIV
2 IC103 qh (FE)
30.5 µs
3.4Vp-p
1V/DIV,
10 µs/DIV
3.8 Vp-p
29.5 ns
1V/DIV, 20ns/DIV
9 IC505 <x/m (CLKB)
6 IC601 qh (CF2)
(CD Play Mode)
• Indication of transistor
C
Note :
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Q
These are omitted.
Approx. 250 mVp-p
100 mV/DIV, 20 µs/DIV
B E
3 IC103 qk (TE)
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
∗ : Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : TUNER
J : CD
h : MD
L : VIDEO
E : PB (TAPE)
a : REC (TAPE)
c : DIGITAL OUT
• Abbreviation
E3
: 220-240 V AC area in E model.
EA
: Saudi Arabia model.
SP
: Singapore model.
TH
: Thai model.
(CD Play Mode)
Q
B C
2.9 Vp-p
1V/DIV,
40 ns/DIV 125 ns
3Vp-p
– MAIN Board –
7 Q207 collector(REC Mode)
E
Approx. 350 mVp-p
These are omitted.
100 mV/DIV, 20 µs/DIV
4 IC103 wk (RFDCO)
(CD Play Mode)
Q
B
C
E
These are omitted.
0.75 ± 0.1 Vp-p
200 mV/DIV, 400 ns/DIV
C
B
E
These are omitted.
29
29
12 Vp-p
13 µs
5V/DIV, 4 µs/DIV
37 ns
1V/DIV, 20ns/DIV
HCD-HP8V
8-1. Block Diagram — CD SERVO Section —
Q102
FREQUENCY
SELECT SWITCH
CONT
A
AUDIO/VIDEO
SECTION
B
AUDIO/VIDEO
SECTION
C
AUDIO/VIDEO
SECTION
D
AUDIO/VIDEO
SECTION
E
MAIN
SECTION
F
AUDIO/VIDEO
SECTION
15
XTSL 189
E
TE
TRACKING
ERROR AMP
D/A3
162 TE
163 SE
18
MDP
E I-V AMP
29
133 137 138
SW
Q101
AUTOMATIC
POWER
CONTROL
1
LD
PD
APC LD
AMP
12
140 141
XTAI
F I-V AMP
IC505 (1/2)
DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO PROCESSOR
160 RFDC
28
XTAO
RFDCI
F
D/A1
SSTP
RFDCO
17
FRDR
FEI
164 FE
16
142 143
135
150
149
FFDR
D
LASER DIODE
LD
FILI
173 RFAC
OPTICAL PICK-UP
BLOCK
(A-MAX. 3)
PD
169
PCO
RFAC
170 171
CLTV
EQ
TRDR
FE
FOCUS
ERROR AMP
RF DC
AMP
10
RFAC
VCA
168
C
DETECTOR
11
EQ
IN
TFDR
9
3
SRDR
8
B
4
SFDR
7
AC
SUM
RF
SUMMING
AMP
26
RFC
6
A
FILO
FILTER
IC103
RF AMP,
FOCUS/TRACKING ERROR AMP
PCMD
BCK
LRCK
C2PO
91
93
88
124
DATA
CLOK
XLAT
SENS
SCOR
SQSO
L_SQCK
L_SCLK
GFS
L_FOK
L_CDXRST
102
111
109
113
126
96
98
114
121
131
105
DATA, BCK,
LRCK, C2PO
DATA
BCK
LRCK
C2PO
DATA, CLOK, XLAT, SENS,
SCOR, SQSO, SQCK,
SCLK, GFS, FOK, XRST
DATA
CLOK
XLAT
SENS
SCOR
SQSO
SQCK
SCLK
GFS
FOK
XRST
• Signal Path
: CD
D/A4
X501
33.8688MHz
2
D/A2
IC102
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
M102
(SLED)
M
5
10
1
2
56
55
47
52
VO4+
VO4–
MOTOR
DRIVE
IN3+
VO3+
VO3–
MOTOR
DRIVE
VO2+
VO2–
VO1+
VO1–
IN4
IN3–
IN2+
COIL
DRIVE
IN2–
IN1+
COIL
DRIVE
IN1–
23
27
26
32
31
D/A1
D/A2
D/A3
D/A4
35
34
3
5
6
9
AO3
AO4
AO5
AO6
IC506
D/A
CONVERTER
RST
M
STBY
(FOCUS) (TRACKING)
2-AXIS
DEVICE
M101
(SPINDLE)
8
4
(LIMIT)
ON : When the optical
pick-up is inner
position
DI 12
CLK 11
LD 10
DATA
CLK
LD
DATA, CLK, LD
SYS RST
SYS RST
30
30
HCD-HP8V
— AUDIO/VIDEO Section —
L_DDAT
L_DCLK
L_XLAT
L_SENS
L_SCOR
L_SQSO
SQCK
SCLK
L_GFS
FOK
XRST
16 MLCK
GPIO14
GPIO13
GPIO11
GPIO12
13 DATA
14 CLK
15 LAT
IC505 (2/2)
MPEG VIDEO/AUDIO DECODER,
VIDEO SIGNAL ENCODER
DRADR0 – DRADR10
DRDAT0 – DRDAT15
NVOEL
DRWEL
DRRAS
DRCAS
DRCK
DRBS
DRDQM0
DRDQM1
GPIO0
GPIO1
GPIO2
GPIO5
GPIO4
GPIO3
CPSIG
34 – 37, 39 – 45
49 – 56, 59 – 66
207
206
74 73 72 68 70 76 77 78
13 14 15 19 18 16
D0 – D15
81 SYSRST
SYS OUT
SYS IN
SYS CLK
SYS CE
SYS OK
SYS RQ
DATA BUS
IC507
D-RAM
39 15 20 38 17 18 16
ROUT
8
IC102
LOW-PASS
FILER
CD-L
G
MAIN
SECTION
R-CH
IC504
DIGITAL FILTER,
D/A CONVERTER
• R-ch is omitted due to same as L-ch.
• SIGNAL Path
: VIDEO
6
DATA, CLK, LD
IC307
VIDEO AMP
D
CD SERVO
SECTION
H
MAIN
SECTION
I
MAIN
SECTION
JK302
VIDEO OUT
B.P.F.
Q301
BUFFER
3
IN
OUT 6
OUTSAG 5
D8 – D15
STBY
2
12 – 5, 27, 26, 31
13 – 15, 17 – 21
23, 25, 4, 28, 29, 3, 2, 30
A0 – A9, A18
DQ0 – DQ7
A10 – A17
IC508
PROM
Q370
VIDEO MUTING
CONTROL SWITCH
VIDEO MUTE
OE
A0 – A10
2, 4, 5, 7, 8, 10, 11, 13, 42,
44, 45, 47, 48, 50, 51, 53
DQ0 – DQ15
7
X502
27MHz
ADDRESS BUS
23 – 26, 29 – 34, 22
30
29
26
28
LOUT
: CD
CLKA
SYS RST
103
110
108
112
125
95
99
115
120
132
106
DATA
BCK
LRCK
AUDXCLKO 205
CLKB
DATA
CLOK
XLAT
SENS
SCOR
SQSO
SQCK
SCLK
GFS
FOK
XRST
L_CDDATA
L_CDBCK
L_CDLRCK
L_CDC2PO
D0 – D7
F
DATA, CLOK, XLAT, SENS,
SCOR, SQSO, SQCK,
SCLK, GFS, FOK, XRST
90
92
87
123
2
1
3
DATA
CLK
LD
CD SERVO
SECTION
C
DATA
BCK
LRCK
C2PO
A0 – A10
CD SERVO
SECTION
DATA, BCK,
LRCK, C2PO
AUDDTO0 201
AUDBCK 203
AUDLRCK 204
A0 – A10
B
24 GPIO9
D0 – D15
CD SERVO
SECTION
CONT
UDQM
LDQM
BA0
CLK
CAS
RAS
WE
A
A0 – A10
CD SERVO
SECTION
24
SYS OUT, SYS IN, SYS CLK
SYS CE, SYS OK, SYS RQ
31
31
HCD-HP8V
— MAIN Section —
L
MD
IN
IC501
POWER AMP
IC301
SOUND PROCESSOR
JK301(1/2)
37 IND2
39 INB2
AUDIO/VIDEO
SECTION
R-CH
R
+10V
40 INA2
Q311 MUTE
R-CH
4
Q507,508
PROTECT
DETECT
D417
L
IC601 (1/2)
SYSTEM CONTROLLER
CLOCK 22
36 RECA2
L-CH
AM
Q609,610
VACS
SA OUT 19
JK601
PHONES
12
2 MIC
VM+10V
11
Q304
MUTE
Q301
DBFB
REF 1
38 INC2
35 RECB2
TUNER PACK
FM
CD-L
G
R CH
3
10
OUT2 25
DATA 21
Q503
OVER LOAD
DETECTOR
Q501
MUTE
MUTE
CONT
SYS MUTE 1
23 VACS
R-CH
RY501
Q306,307
D505
Q510
PROTECT
SWITCH
Q509
PROTECT
CONT
JK501
SPEAKER
Q512
RELAY
DRIVE
Q513
PROTECT
SWITCH
R CH
R
7 MCLK
D OUT
96 DI
D IN
95 DO
CLK
97 CLK
CE
+VCC
Q511
PROTECT
SWITCH
TH501
9 CE
TUNED
Q504,506
OVER HEAT
DETECTOR
75 STEREO
Q514,515
D507
Q505
FAN
SWITCH
74 TUNED
STEREO
D509
FAN
DRIVE
FAN
• R-ch is omitted due
to same as L-ch.
• Signal Path
MUTE
Q309
+4V
+3.3V
MUTE
CONT
PROTECTOR 82
78 CD MUTE
: TUNER
FLD601
RES601
8MHz
15 CF1
: CD
FLOURESCENT
INDICATOR TUBE
VR001
IC001(1/2)
MIC AMP
JK001
3
42
MIC LEVEL
IC001(2/2)
MIC AMP
1
6
+
MIC
X601
32.768kHz
12 XT1
P1
13 XT2
7
AUDIO/VIDEO
SECTION
H
VIDEO MUTE
P22
ECHO LEVEL
2
ECHO
AMP
AUDIO/VIDEO
SECTION
9
I
SYS OUT, SYS IN,
SYS CLK, SYS CE,
SYS OK, SYS RQ
SYS CLK
SYS CE
SYS OK
SYS RQ
98 SYS OUT
CD CERVO
SECTION
L
E
41
30
+3.3V
3
1
REG
D+3.3V
SYS RST
TO IC001
D+5V(SW)
FUNCTION
KEY
IC404
1
+5V
REG
VM+10V
1
10 SYS OK
+4V
1
B+
SWITCH
KEY2 24
FUNCTION
KEY
DISC1 LED 92
LED607-611
: MIC INPUT
D401-404
IC402
+3.3V
REG
+3.3V
+4V
REG
3
FAN+B
D405-408
IC403
1
VCC+10V
M+7V
(UNSW)
DISC2 LED 91
4 SYS RST
+10V
3
REG
D302-305
Q412
DISC3 LED 88
-VFL
REG
-VFL
DISC4 LED 87
DISC5 LED 86
Q314
Q313
MUTE
EXCEPT TH
D907
S902
VOLTAGE
SELECTOR
LED614
PWR LED 93
85 LINE OUT MUTE
MUTE
CONT
D410
Q581
FUNCTION
KEY
S614-622
6 SYS RQ
: REC (TAPE)
D412
+10V
3
REG
Q401,402
3
A+5V(SW)
KEY1 25
-VCC
REG
S601-610
5 SYS CE
: DIGITAL OUT
: PB (TAPE)
IC401
+4.5V
REG
+4.5V(BD)
: MD
+VCC
POWER
AMP
Q001
Q201
99 SYS IN
100 SYS CLK
R-CH
R
G1
G12
D501
+2.5V
1
REG
IC202
50
.
52
KEY0 26
JK301(2/2)
MD
OUT
3
FIL1
S627-636
SYS OUT
SYS IN
MUTE
45
.
47
A+2.5V
FIL2
65
76 VIDEO MUTE
VR002
IC002
T901
MAIN TRANS
IC201
16 CF2
FIL1
FIL2
CD POWER 3
VR601
VOLUME
ENCODER
D622
PWR DOWN 27
79 VR ENC A
80 VR ENC B
EVER+3.3V
Q601
RESET 11
IC603
RESET
SWITCH
3
RM601
REMOTE
CONTROL
RECEIVER
RESET
D901-904
T902
SUB TRANS
IC602
D620
5
1
+4V
REG
1
AC
IN
EVER+10V
D624
D413
Q410
28 REMCON IN
D414
VM+10V
IC302
I/O EXPANDER
RY901
RELAY
DRIVE
Q411
POWER
CONTROL
POWER RELAY 94
DI1 26
IC601 (2/2)
SYSTEM CONTROLLER
CLK 3
LATCH 4
IC201
PB/REC EQ AMP
DECK
PB OUT(L) 26
34 PB IN(L)
21 REC OUT(L)
REC/PB
HEAD
R-CH
12 P8
Q209
MUTE
18 TCM
REC MUTE ON/OFF 15
MUTE ON/OFF 14
19 P5
20 P4
P10 10
7 FIN
OUT1 4
P11 9
9 RIN
OUT2 2
VM+10V
MECHA BLOCK
DECK
MOTOR
M
Q408,409
MOTOR
DRIVE
T SOL
DRIVE
1
P12 8
P13 7
7 FIN
OUT1 4
9 RIN
OUT2 2
M
M781
(ROLLER)
S711 (DISC INSERT(8/12cm))
CDM SW1-A 71
S713 (DISC IN (8/12cm))
IC721
STOCKER MOTOR DRIVE
22 P2
P14 6
7 FIN
OUT1 4
P15 5
9 RIN
OUT2 2
CDM SW2-A 70
S714 (DISC IN (8cm))
M
M761
(STOCKER)
CDM SW2-B 69
S715 (DISC OUT)
CDM SW3 73
24 P0
S718 (STOCKING)
S711 (ON : When disc insert)
S713 (ON : Play position)
S714
S718
OFF: In the Midst disc is moving
between play position and
stocker
S717
In the midst disc is moving
between play position and stocker
ON : disc is play position side
OFF : disc is stocker side
S716
ON : The moment disc in/out
from stocker
S717 (DISC POSITION)
CDM SW5-A 67
P7 17
S716 (STOCKER IN/OUT)
CDM SW5-B 66
SW401
TAPE
OPEN/CLOSE
CDM D SENSOR 81
END
32
32
Q731
LEVEL
SHIFT
IC751
DISC INSERT
DETECT SENSOR
ON : Play position
(8cm disc only)
S715 (ON : When disc out from play position)
CDM SW4 68
P6 18
23 P1
R REC
PACK
G
4
PLAY
F REC
2
CDM ELVE 20
21 P3
Q406,407
SOL
M771
(MODE)
3
Q211
Q206
SWITCH
M
IC711
ROLLER MOTOR DRIVE
Q208
Q205
S702
ROTARY ENCODER
(STOCKER POSITION)
IC701
MODE MOTOR DRIVE
A/B 13
Q212
BIAS
G
3
CDM SLDE 21
4
R-CH
Q201
Q203
1
2
83 TAPE END
ALC(L) 23
Q207
BIAS
OSC
CDM SLDE1 22
19 TCM1
11 P9
REC IN(L) 24
L201
BIAS
ERASE
HEAD
S771
ROTARY ENCODER (MODE)
8 CE
HCD-HP8V
8-2. Printed Wiring Boards — BD Section — • See page 28 for Circuit Boards Location.
1
A
2
3
4
5
BD BOARD (COMPONENT SIDE)
6
7
8
BD BOARD
(CONDUCTOR SIDE)
(SPINDLE)
M
• Semiconductor
IC102
Location
Ref. No.
E
B
D101
C
30
16
TP70
(TE)
TP68
(FE)
TP72
(RFAC)
TP71
(RFDC)
J
1
IC103
15
TP73
(DVC)
VMP
BOARD
CN101
(Page 35)
D
E
12
1-684-174-
(12)
M
OPTICAL
PICK-UP
BLOCK
(A-MAX. 3)
E
(SLED)
12
1-684-174-
33
33
(12)
Location
D101
C-6
IC102
IC103
B-7
D-6
Q101
Q102
D-6
B-6
HCD-HP8V
8-3. Schematic Diagram — BD Section — • See page 47 for IC Block Diagrams. • See page 29 for Waveforms.
TP27
C115
47
6.3V
R104
15k
AA1
C107
33p
C117
0.1
C120
47
4V
C112
47
4V
C109
0.1
R120
120k
CN102
16P
TP26
I1-6
CC2
TP25
I5-10
TP49
AA5
FE
VC
RFAC
R227 100k
AA9
CC1
FEI
DVC
TE
DVCC
AA3
VCC
C103
470p
AA2
C101
470p
C102
0.1
R102
15k
R105
1k
TE_BAL
C104
0.0033
R112
0
R103
100k
AA10
D101
1SS355
R114
47k
R111
120k
Q102
UN2111-TX
R109
100k
AA4
CE
F
CEI
E
VCC
D
RFG
C
BST
B
VFC
A
R126 33k
CC1
R125 33k
CC2
TP24
CC3
TP23
CC4
TP55
TP56
MGND
STBY
TP57
TP58
RFDCI
PD
DC_OFST
LD
R117
47k
IC103
CXA2581N-T4
Q101
2SB710A-RT
BB8
TP59
BB1
SRDR
TP60
BB2
TFDR
TP61
BB3
TP62
BB4
FFDR
TP63
BB5
FRDR
TP64
BB6
J
SSTP
TP65
VCC(4.5V)
TP66
VMP BOARD
(1/2)
CN101
(Page 37)
GND
TP67
T+
TP52
F+
POWER
ERROR AMP
CONTROL
R124
10
C119
1
C113
100
4V
R122
100k
C111
47
4V
C108
0.1
F-
TP50
C118
1
AUTOMATIC
FOCUS/TRACKING
TP22
TRDR
T-
TP53
C114
0.001
BB7
SFDR
LD
C110
0.1
EQ_IN
RF AMP,
MDP
PD
CC5
R118
0
R236
1k
SW
CC5
TP51
R229
2.2k
MGND
PD1
TP54
AA8
AA7
7V
GND
CC4
LD_GND
R228
470k
AC_SUM
VC
RFDCO
CN101
28P
PD2
CC3
GND
RFC
R113
2.7k
SELECT
SWITCH
AA6
VCC
FREQUENCY
TP21
(CHASSIS)
R231 1k
SW
R123
10
R235
1k
AA2
TE
TP70 (TE)
AA3
RFDC
TP71 (RFDC)
RFAC
TP72 (RFAC)
DVC
TP73
DVCC(2.5V)
TP74
LD ON(D/A4)
TP75
AA6
D/A3
TP76
AA7
D/A2
TP77
AA8
D/A1
TP78
AA9
CTRL
TP79
AA10
LD GND
TP80
BB6
AA1
TP69
C166
0.1
BB5
TP68 (FE)
SE
BB3
FE
BB4
GND
AA4
C213 0
C182
100
10V
AA5
VO2+
VO2VO3+
PGND1
VO3-
PGND1
PGND2
PGND2
NC
VO1-
NC
NC
NC
NC
PVCC/
2(NC)
NC
PVCC1
VO1+
PVCC1
PVCC2
PVCC2
NC
NC
NC(BC2)
NC(VDD)
NC
(VPUMP1)
NC(CT)
NC(BC1)
OP-
OP+
NC(SW)
OP.O
NC(FB)
IN1-
OPO1(NC)
IN1+
IN2-
IN2+
FOCUS/TRACKING
VO4+
NC
STBY
VO4-
NC
NC(BC4)
NC
IN4
(VPUMP2)
NC
ABS
VREF
IN3-
IN3+
IC102
AN41020A
SVCC
MOTOR DRIVE
NC(BC3)
COIL DRIVE,
SPINDLE/SLED
IN4R
C153
0.1
OPO3(NC)
C165
10
16V
M102
(SLED)
R179
10k
R176
0
M101
(SPINDLE)
R152
4.7k
C151
0.022
BB7
BB2
BB8
R151
100k
BB1
R234
0
OPO2(NC)
SGND
(DVC)
C163
100
10V
C164
0.1
no mark:CD(PLAY)
34
34
HCD-HP8V
8-4. Printed Wiring Boards — VMP Section (1/2) — • See page 28 for Circuit Boards Location.
R102
R114
L102
R152
C114
C597
R516
C115
IC102
C596
C582
C584
C503
EP200
R115
VMP BOARD (COMPONENT SIDE)
• Semiconductor
Location
Ref. No.
EP202
C551 R517
R502
C365
IC508
R557
R556
R555
R551
IC505
R554
R552
C543
C544
C573
C540
FB501
C258
JW203
R533
C570
C524
R202
C538
C567
C209
C210
FL201
C525
FB252
C561
C211
C214
A1
CN101
EP201
C212
I
J
TO JACK BOARD(Page 41)
CN307
TO BD BOARD(Page 33)
CN101
35
35
A-10
E-10
C-6
C-3
C552
R558
CN301
C502
CN201
C366
IC102
IC202
IC505
IC508
C501
Location
IC202
A
TO MAIN BOARD
CN301
(Page 41)
HCD-HP8V
8-5. Printed Wiring Boards — VMP Section (2/2) — • See page 28 for Circuit Boards Location.
C581
R109
C154
R322
C322
R323
FB504
R511
R512
R509
C566
IC506
B1
R531
C254
FB251
R561
36
36
C574
C223
C224
C255
C257
C203
FB561
IC201
C253
X501
R534
R201
C571
FL502
C521
C522
R532
C576
C575
IC507
R538
R537
C511
R510
C536
R544
C222
FB201
C208
C533
C534
Q201
C513
C523
R548
C539
R541
C541
R547
C537
C221
C213
C202
R549
C535
R550
C204
FL504
C201
FB502
R546
C542
C205
C206
R545
R542
FB503
C510
R522
R543
FL503
C547
C259
C504
C549
C572
R559
X502
Location
IC201
IC307
IC504
IC506
IC507
F-1
A-9
A-3
E-9
D-8
Q201
Q301
Q370
Q581
E-3
A-5
B-10
A-3
Q370
C505 FL501
R513
C546 C548
R503
Ref. No.
C550
C545
R504
Location
R376
R321
R508
R507
R506
R505
• Semiconductor
R375
C207
L321
C321
C360
R158
IC504
C361
C364
Q301
C323
IC307
C583
FB360
C104
R159
C155
C156
C116
R582
R581
R107
C338
C105
R157
R108
C106
Q581
VMP BOARD (CONDUCTOR SIDE)
HCD-HP8V
8-6. Schematic Diagram — VMP Section (1/2) — • See page 48 for IC Block Diagrams.
VMP BOARD
IC B/D
IC102(2/2)
C105
CN201
R109
TP419
TP418
R108
C104
R102
TP417
C258
C106
R107
C156
R157
C581
0
TP416
TP415
TP414
C596
Q581
R152
TP413
TP412
C259
R159
R115
R158
C154
IC504
TP411
CN301
(Page 42)
TP410
A
C115
TP409
R114
C114
C582
R581
IC102(1/2)
C155
R582
TP408
C584
C583
C597
TP407
TP406
C116
L102
TP405
TP404
TP403
TP402
FB360
TP401
Q370
C360
R376
4.2
VMP
C361
IC307
(Page 38)
TP310
R323
C322
Q301
BUFFER
0.3
L321
R321
C321
C338
C365
TP303
R375
C364
C366
R322
C323
IC B/D
C257
VIDEO AMP
CP
CN101
0.9
TP309
TP421
TP422
R202
TP424
TP425
TP426
TP427
TP428
TP429
TP430
TP431
TP432
TP433
J
(Page 34)
FB252
TP434
C255
TP436
C254
Q201
4.2
TP437
R201
TP438
C224
4.9
TP439
C221 C222
TP440
C223
CN301
TP441
TP308
FB251
TP442
TP307
TP443
I
TO JACK
CN307
(Page 42)
TP444
TP445
TP446
TP447
TP448
JW203
no mark:CD(STOP)
37
37
HCD-HP8V
8-7. Schematic Diagram — VMP Section (2/2) — • See page 48 for IC Block Diagrams. • See page 52 for IC Pin Function. • See page 29 for Waveforms.
IC201
VMP BOARD
C204
C201
C205
C213
C202
FB503
FB501
FL504
FB502
FL503
TP197
C206
C203
C253
C207
C208
C543
R544
C534
R541
R546
R542
R545
R543
TP172 C570
C533
C537
R548
TP177
C540
TP178
TP183
TP182
TP191
C536
C535
C546
TP198
TP201
TP203
TP202
0
TP204
C548
R550
C545
R554
R555
C542
TP173
C549
R556
R551
R549
C547
TP205
C551
TP208
C212
R547
C541 C539
R552
X502
27MHz
C552
R559
C211
TP209
C214
C210
TP215
C209
TP216
R558
FL201
C538
C544
R557
C550
FB504
IC202
1.5 TP193
1.5 TP192
FB201
C501
VMP
(Page 37)
R516
R534
TP1
C502
R502
TP2
R517
TP3
9
TP159
TP4
TP158
TP5
C503
R533
TP157
TP6
TP156
TP7
TP8
IC B/D
R561
FB561
R537
TP9
C524 C525
TP10
C566
C574
R538
TP11
IC506
TP151
TP12
TP302
TP306
C567
R504
TP14
R505
TP15
R506
TP16
C523
R532
C522
X501
TP17
TP146
R507
TP18
TP145
R508
TP19
TP20
C504
TP21
R513
C561
8
TP13
R503
TP22
TP23
TP24
TP25
R509
TP26
TP136
TP27
R510
TP28
IC505
R511
TP29
R512
TP30
DIGITAL SIGNAL PROCESSOR
DIGITAL SERVO PROCESSOR
MPEG VIDEO/AUDIO DECODER
VIDEO SIGNAL ENCODER
TP31
FL501
PROM
TP134
TP132
C521
FL502
TP130
TP33
IC508
R531
2.4
C575
IC507
TP129
-0B1MAZ060
TP128
C573
TP127
TP126
TP124
TP122
TP121
C576
TP119
TP118
TP117
TP116
TP115
C505
C571
C572
TP113
TP111
TP106
TP102
TP100
TP99
TP97
TP96
TP94
TP93
TP91
TP89
TP86
TP88
TP85
TP83
TP82
TP84
TP81
TP80
TP79
TP73
TP74
TP72
TP70
TP68
TP67
TP109
C511
C513
R522
C510
no mark:CD(STOP)
38
38
HCD-HP8V
8-8. Printed Wiring Boards — Changer Section — • See page 28 for Circuit Boards Location. •
1
2
3
: Uses unleaded solder.
4
5
6
7
9
8
A
• Semiconductor
Location
TO
MAIN
BOARD
CN302
(Page 41)
Ref. No.
B
C
IC701
IC751
IC721
IC711
D
S718 (STOCKING)
OFF: In the Midst disc is moving
between play position and
stocker
S717 (DISC POSITION)
In the midst disc is moving
between play position and stocker
ON : disc is play position side
OFF : disc is stocker side
E
S716 (STOCKER IN/OUT)
ON:The moment disc in/out
from stocker
39
39
Location
D701
D711
D721
C-4
C-4
C-4
IC701
IC711
IC721
IC751
C-4
D-4
C-4
C-2
Q731
B-5
HCD-HP8V
8-9. Schematic Diagram — Changer Section — • See page 49 for IC Block Diagrams.
CN751
3P
1
DIODE
IC751
CN702
3P
1
D SENSE
D SENSE
GND
IC751
RPR-220
R731
91
DIODE
R733
10k
GND
3
CN701
27P
R734
12k
3
3.2
R732
1k
RIN
FIN
GND
VCC
OUT1
VM
OUT2
RNF
VREF
DISC INSERT
DETECT SENSOR
D+3.3V
M+12V
Q731
RT1N141
M+12V
LEVEL
MGND
MODE MOTOR
DRIVE
SHIFT
MGND
D.SENSOR
IC701
BA6956AN
C754
0.1
C711
10
50V
C758
0.1
R702
100
R701
680
D701
MTZJ-T-77-4.7B
CN781
2P
1
SW2A
SW2-A
SW2B
SW2-B
C751
0.1
SW5B
SW5-B
SW5A
SW5-A
C781
0.01
MD NEG
RIN
FIN
GND
2
VM
2
VCC
-
RNF
VREF
MTR RL 1
OUT1
ROL NEG
MTR RL 1
(ROLLER)
MTR RL 2
OUT2
+
M781
MD POS
CN703
2P
1
SW3
SW1-A
C756
0.1
C752
0.1
MTR RL 2
SW3
SW1
C755
0.1
ROL POS
ROLLER MOTOR
MAIN BOARD
CN302
(Page 42)
ELV POS
DRIVE
ELV NEG
SW4
RIN
GND
VCC
FIN
VM
RNF
OUT1
VREF
OUT2
SW4
IC711
BA6956AN
C753
0.1
STOCKER MOTOR
P02 SLD E1
R712
100
DRIVE
SLD E2
IC721
BA6956AN
+
M761
(STOCKER)
CN761
2P
1
MTR ST 2
CN704
2P
1
MTR ST 2
C761 R722
0.01
100
SLD E3
C765
0.1
R711
680
D711
MTZJ-T-77-5.6B
ELV E0
ELV E1
C764
0.1
ELV E2
C763
0.1
MTR ST 1
MTR ST 1
SLD E0
ELV E3
2
C762
0.1
2
D721
MTZJ-T-77-3.6A
R721
680
S702
ROTARY ENCODER
(STOCKER POSITION)
CN711
2P
1
CN705
2P
1
GND
GND
SW1
SW1
S711
2
2
CN721
3P
1
1
SW1
(DISC INSERT(8/12cm))
(ON:WHEN DISC INSERT)
GND
S713
CN706
3P
GND
SW2-A
SW2-A
SW2A
SW2-B
SW2-B
SW2B
(DISC IN(8/12cm))
3
(ON:PLAY POSITION)
3
S714
(DISC IN(8cm))
(ON:PLAY POSITION(8cm DISC ONLY))
S771
ROTARY ENCODER
(MODE)
CN731
2P
1
GND
CN707
2P
1
SW3
S715
SW3
2
CN710
7P
1
E1
C769
0.1
GND
SW3
E1
E2
E2
C768
0.1
GND
2
(DISC OUT)
CN771
7P
1
GND
C767 0.1
E3
E3
C766 0.1
E4
E4
(ON:WHEN DISC OUT FROM PLAY POSITION)
MTR MD 1
MTR MD 1
MTR MD 2
CN741
4P
1
GND
S716
(STOCKER IN/OUT)
CN708
4P
1
C771
0.01
GND
SW5-B
SW5-B
SW5B
SW5-A
SW5-A
SW5A
SW4
SW4
SW4
4
M771
-
4
S717
(DISC POSITION)
IN THE MIDST DISC IS MOVING
BETWEEN PLAY POSITION AND STOCKER
ON:DISC IS PLAY POSITION SIDE
OFF:DISC IS STOCKER SIDE
S718
(STOCKING)
OFF:IN THE MIDST DISC IS MOVING
BETWEEN PLAY POSITION AND STOCKER
No mark : CD(STOP)
40
40
7
+
ON:THE MOMENT DISC IN/OUT
FROM STOCKER
MTR MD 2
7
(MODE)
HCD-HP8V
8-10. Printed Wiring Boards — Main Section — • See page 28 for Circuit Boards Location. •
: Uses unleaded solder.
• Semiconductor
Location
Ref. No.
1
3
2
4
5
6
7
8
JK302
1
C371
2
3 4 5
TO
VMP
BOARD
CN301
(Page 35)
12
VIDEO
OUT
6 7 8
I
12
3
A
CN307
1
JACK BOARD
1-689-247-
C372
E
CN309
JW459
1
(TAPE OPEN/CLOSE)
4
E
E
E
E
37
30
C364
IC301
4 5
E
C363
E
1
9
E
IC201
E
E
E
E
E
R397 R396
R369
E
E
E
R333
E
E
R332
C315
E
7
3
1
IC201
IC301
IC302
IC401
IC402
IC403
IC404
C-3
B-4
D-3
C-5
C-5
C-4
D-5
R355
E
IN
C423
L
1
4
CN405
5
1
R394
MD
C360
18
19
2
R398
JW301
E
R
R399
JW427
R340 R464
D
E
Q201
Q202
Q203
Q204
Q205
Q206
Q207
Q208
Q209
Q210
Q211
Q212
Q301
Q302
Q304
Q305
Q306
Q307
Q309
Q310
Q311
Q312
Q313
Q314
Q401
Q402
Q406
Q407
Q408
Q409
Q410
Q411
Q412
B-3
B-3
B-3
B-3
B-3
C-2
C-2
C-2
C-3
C-3
E-4
C-2
C-4
B-4
C-6
C-6
B-5
C-5
D-3
C-3
C-3
C-8
C-8
D-1
E-5
E-5
C-2
C-2
C-2
C-2
B-7
B-7
C-7
3
R
9
JR307
JR313
OUT
L
R395
C365
G
C421
1
JW430
TO
PWR TRANS
BOARD
CN907
(Page 45)
3
C408
IC404
R341
Q314
IC401
8
1
8
2
1
JW429
1
IC402
3
1
2
1
E
R331 Q311
R366 JR308
CN405
R358 Q309
C422
IC403
Q310
2
1
E
E
E
R370
JW414
10
Q312
E
E
E
R371
C
IC302
Q402
C409
1
E
4
2
1
20
10
R401
R434
26
27
E
Q401
D
E
TO
PANEL
BOARD
CN603
(Page 43)
B-7
B-7
B-5
D-4
D-4
D-4
D-4
E-4
D-5
E-3
D-7
D-7
D-7
D-7
D-7
C-7
D-7
C-7
D-2
D-7
D-1
E-7
C-7
B-7
C-7
C-6
E-6
C347
E
Q313
TO
PANEL
BOARD
CN601
(Page 43)
10
36
C307
B
2
11P
E
Location
D101
D102
D301
D302
D303
D304
D305
D306
D307
D309
D401
D402
D403
D404
D405
D406
D407
D408
D409
D410
D411
D412
D413
D414
D415
D416
D417
1
R402
13
R403
R437
E
12
1-689-244TO
CONNECTOR
BOARD
CN701
(Page 39)
B
TO
VMP BOARD
CN201
(Page 35)
A
TO
PANEL
BOARD
CN602
(Page 43)
C
TO
PANEL
BOARD
CN004
(Page 43)
TO
PWR AMP
BOARD
CN501
(Page 45)
H
41
41
F
(CHASSIS)
12
HCD-HP8V
8-11. Schematic Diagram — Main Section — • See page 49 for IC Block Diagrams. • See page 29 for Waveforms.
B
TO
CONNECTOR BOARD
CN701
(Page 40)
27P
MAIN BOARD
ANTENNA
FM75Ω
COAXIAL
AM
3.3
3.2
0
3.3
0
3.2
0
0
3.3
3.3
CN101
11P
IC302
0
I/O EXPANDER
-3.4
0.1
0.1
0.1
0.1
0.1
0.1
0.1
-3.4
Q309-311
MUTE
1000P
-3.4
1K
0
3.2
0.022
-3.4 MUTE CONT
-3.4
0
0.1
9P
100K
0.1
MUTE
MUTE
3.3
2SD1306NETL
2SD1306NETL
19P
100K
DBFB
L
*
470P
1K
R
MD
A
TO
VMP
BOARD
CN201
(Page 37)
4P
4.3
4.6
OUT
JK301
C
*
*
4.7
TO
PANEL
BOARD
CN602
(Page 44)
0.0027
L
0
0
*
*
*
*
0
0
4.6
4.7
0.082
0
4.7
4.6
4.6
4.6 0.047
4.6
0.022
4.6
4.6
4.6
4.6
4.7
4.6
4.6
4.6
4.7
4.7
0.047
R
0.022
IN
4.6 4.7
0.1
9.2
4.6
4.7
IC404
0.2
4.7
4.6
4.6
9.2
+5V REG
4.6
4.2
DBFB
0.7
0
4.7
0.7
2SD1306NETL
Q401,402
B+ SWITCH
IC403
+10V REG
Q304,305
MUTE
0.047
8.2
8.4
15.6
C307
4.7U 50V
I
10
8.2
4.7K
Q406,407
T SOL DRIIVE
5
7.6
0.0022
C420 0.1
1000
VIDEO
OUT
Q306,307
MUTE
CONT
TA7810S
R355 4.7V
470
0
10
6800U 6.3V
JACK
BOARD
TO
VMP
BOARD
CN301
(Page 37)
9.9
9.9
0.082
0.047
2SD1306NETL
0.7
0.0027(M)
4.6
4.6
0.022 4.6
SOUND
PROCESSOR
0.022 4.6
4.6
4.6
4.6
4.6
4.7
IC301
4.6
4.6
0
10
0.1
0.7
0.1
10
3.0
0
3.7
0.5
3.7
HEAD
(REC/PB/ERASE)
UPC3504AHF
0
IC402
+4V REG
4
9.2
10
470
RELAY DRIVE
9.2
9.2
C423
0.1u
C422
0.1u
7.5
PB/REC EQ AMP
10
8.4
IC401
2.5
0
10
0
0
REC/PB R-CH
TA7810S
MUTE
IC201
0
0.1
0
1.3
L-CH
16.6
3.7
3.8
3.7
0.6
0.6
3.0
0.015
MUTE 0
Q408,409
MOTOR
DRIVE
0
+10V REG
0.7
10
0
0
EH
POWER CONTROL
0.6
ERASE
0.6
3.8
0.6
3.0
0.015
0.047
TAPE
MECHANISM
DECK
SWITCH
0
0.7
0
0.5
0.7
0
0.7
0
0.0022
Q201-204
SWITCH
0
0
8P
7
0.0022
9.9
9.9
0.0022
0
SWITCH
9.9
25V
0
9.2
16V
9.9
BIAS OSC
SWITCH
0
0
0.015
0.015
0.7
0.015
9.9
0
0.0047
SWITCH
-VFL REG
BIAS
1/2W
-26.5
0
-37.5
-27
0
0
1/2W
UDZSTE175.6B
5P
UDZSTE1727B
0
3.0
0
0.7
3.8
3.7
0
3.7
0
No mark:FM
0
37P
4P
13P
9P
F
G
TO
PWR TRANS
BOARD
CN907 (Page 46)
42
H
E
42
TO
PANEL
BOARD
CN601 (Page 44)
TO
PANEL
BOARD
CN004 (Page 44)
TO
PWR AMP
BOARD
CN501 (Page 46)
D
TO
PANEL
BOARD
CN603 (Page 44)
HCD-HP8V
5
TO
MAIN BOARD
CN405
(Page 41)
TO
MAIN
BOARD
CN303
(Page 41)
6
7
H
C020
(VM10V)
CN004
5
R002
C003
R012
S614
+
1
R006
JW004
C006
-
PRESET/ALBUM
C012
C015
S610
DISC1
JW005
VR002
D627
RM601
S601
DISC1
S621
S622
41
1
R013
45
MIC LEVEL
3
S633
GROOVE
S634
DIMMER
C008
ECHO LEVEL
S636
Location
C014
R620
B
• Semiconductor
R009
Q001
E
PRESET EQ
S635
C009
VR001
FUNCTION
MIC
R010
R011
S627
JK001
3
A
4
WIRE001
C
PANEL BOARD
3
JW003
2
JW001
(A-GND)
1
: Uses unleaded solder.
JW002
8-12. Printed Wiring Boards — Front Section — • See page 28 for Circuit Boards Location. •
C007
1
3
R005
IC001
C002
R004
C004
R003
C001
JW006
(VM10V)
30
8
C005
1
S609
DISC2
S602
DISC2
S615
4
5
C011
C013
R009
R008
R001
VOLUME
S603
DISC3
20
(TH)
S608
DISC3
C010
R033
C051
C052
S617
R022
C046
R097
C053
R095
R098
C048
E
FLASH R/W
3
1
IC603
S604
DISC4
E
D003
IC002
S607
DISC4
1
EA
10
R096
R094
C050
R093
R092
C049
8
S618
R091
9
D
C032
C054
16
IC601
R619
JW008
S616
JW007
C
(FLUORESCENT INDICATOR TUBE)
TUNER/BAND
S620
5
+
-
S606
DISC5
S629
S630
REPEAT
PLAY
MODE
E
S631
CD SYNC
S628
DISPLAY
S605
DISC5
R099
R029
C041
S632
C043
(A-GND)
1
C047
TUNING
JW009
S619
TUNING
C044
C042
C045
REC(PAUSE/START)
C610
E
4
5
3
C609
1
IC602
F
1-689-249TO
MAIN
BOARD
CN402
(Page 41)
TO
MAIN
BOARD
CN305
(Page 41)
E
43
D
43
(CHASSIS)
Ref. No.
Location
D606
D607
D615
D616
D617
D619
D620
D621
D622
D623
D624
D625
D626
D-1
D-1
D-4
C-5
D-4
E-3
E-4
F-3
E-4
D-4
E-4
E-3
F-4
IC001
IC002
IC601
IC602
IC603
C-6
D-7
C-2
F-4
D-4
LED607
LED608
LED609
LED610
LED611
LED614
B-5
C-5
C-5
D-5
E-5
B-2
Q001
Q601
Q609
Q610
B-6
E-3
D-5
D-5
RM601
B-2
HCD-HP8V
8-13. Schematic Diagram — Front Section — • See page 47 for IC Block Diagrams. • See page 50 for IC Pin Function. • See page 29 for Waveforms.
TO
MAIN BOARD
CN303
(Page 42)
C
PANEL BOARD
(FLUORESCENT INDICATOR TUBE)
PHONES
0
C610 1000P
0
D
0
C609
1000P
0
TO
MAIN
BOARD
CN305
(Page 42)
9.6
5.9
ENCODER,ROTARY
H
-26.5
-16.5 @ @
-24
EA
TH
-26.4
-24
-19
-16.5
-19
-19
-16.5
-19
-26.4
-26.4
-26.4
-21.5
0
0
0
0
0
3.4
0
3.2
3.4
2.2U
*
VACS
3.4
R033
12K
0.4
3.3
1
3.3
5.9
2.2K
0
R619
10K
5.2
3.4 @ @ @ @ @ @ @ @
VACS
VCD
3.8
-26.4
3.3
-24
3.2
-24
0.7
-19
3.3
0
0.7
VOLUME
-11.7
0.7
0.7
IC601
-14.1
SYSTEM CONTROLLER
-26.4
-14.5
-25
3.3
0.7
IC001
0.7
-25
2.7
-25
-25
0
4.3
3.3
TO
MAIN
BOARD
CN402
(Page 42)
0
-25
37P
AEP,UK,RU
3.3
-25
3.5
0.3
2.8
1.9
2.4
0.4
1.7
1.5
3.3
1.4
0
0
0
0
0
3.3
18P
I/
R620 10K
0
3.3
1.5
3.3
-25
3.3
3.2
2.9
-25
3.3
3.3
0
VR001
MIC LEVEL
-25
-25
1.7
4.4
4.3
6
0
22P
4.2
E
-25
5
0
MIC
IC001
-25
LC876796B-51Y2-E
3.2
(1/2)
IC603
IC602
RESET
9.9
+4V REG
4.3
4.3
3.5
(2/2)
REG
4.9
3.4
0
9.9
D627
1SS355
4.3
4
1.3
8.4
8.4
0.01
I/
0.022
UDZSTE-175.1B
22
25V
0
2.6
2.6
2.6
2.6
2.6
0.9
5.1
VR002
ECHO LEVEL
3.3
0.33U
0.33U
C607 100U 16V
R685
220
1/8W
R684
220
1/8W
0.6
2.6
2.6
2.6
RESET SWITCH
2.6
TO
MAIN
BOARD
CN405
(Page 42)
3.3
RM601
3.3
IC002
No mark:FM
44
44
HCD-HP8V
8-14. Printed Wiring Boards — PWR AMP/Power Section — • See page 28 for Circuit Boards Location. •
1
3
2
: Uses unleaded solder.
4
5
PWR TRANS BOARD
4
7
SUB TRANS BOARD
T901
POWER TRANSFORMER (MAIN)
A
6
3
2
1
EXCEPT TH
CN906
4P : EXCEPT TH
2P : TH
EXCEPT TH
*
2P : TH
2
*
EXCEPT TH
S902
4
TH
* CN905
4P : EXCEPT TH
3
4
4
VOLTAGE SELECTOR
120V
3
EXCEPT TH
220V
TH
3
230-240V
• Semiconductor
2
B
Location
2
EXCEPT TH
Ref. No.
TH
7
5
6
1
1
EXCEPT TH
TH
TH
EXCEPT TH
T902
POWER TRANSFORMER (SUB)
14
13
12
11
10
9
8
7
6
1
5
2
3
EXCEPT TH
4
TH
9
1
1
4
3
1-689-250-
1
C
(CHASSIS)
TH
TO
MAIN
BOARD
CN401
(Page 41)
8
G
EXCEPT TH
6
3
PWR AMP BOARD
AC IN
1
1
(CHASSIS)
12
2
3
D
1
4
E
E
E
E
1
E
F
3
1
2
E
E
E
E
E
IC501
2
1
E
E
5
4
6
R551
E
SENSOR (FAN)BOARD
C530
E
E
3
C532
E
R550
1
C529
2
C531
F
TO
MAIN
BOARD
CN404
(Page 41)
12
C527
12
C528
12
1-689-248-
1-689-245-
L SPEAKER R
(IMPEADANCE USE 6-16
)
45
45
12
4
1-689-246-
12
Location
D501
D502
D503
D504
D505
D506
D507
D508
D509
D901
D902
D903
D904
D905
D907
D-2
E-2
E-1
E-2
E-4
E-4
F-4
F-4
E-4
C-6
C-6
D-6
D-6
D-7
B-2
IC501
F-2
Q501
Q502
Q503
Q504
Q505
Q506
Q507
Q508
Q509
Q510
Q511
Q512
Q513
Q514
Q515
E-2
E-2
E-1
E-3
F-3
E-3
E-4
E-4
D-3
D-4
D-3
E-4
E-4
E-3
E-3
HCD-HP8V
8-15. Schematic Diagram — PWR AMP/Power Section — • See page 49 for IC Block Diagrams.
FAN
SPEAKER
IMPEADANCE
USE 6-16Ω
3P
-
14.3
C516
0.22U
+
-
+
C528 0.1U
4P
0
JR502
4P
PWR TRANS BOARD
C531
14.4
4.7K
C532
(TO CHASSIS) PROTECT C527
CONT 0.1U
FAN DRIVE
C530
0
PROTECT SWITCH
0
10
0
0
PROTECT
SWITCH
0
9.9
3.3
C529
9.9
G
F
TO
MAIN
BOARD
CN401
(Page 42)
RELAY DRIVE
0.2
0.4
0.8
2.2
13P
9P
0.9
PROTECT
SWITCH
0.2
TO
MAIN
BOARD
CN404
(Page 42)
JW911 *
3.9
POWER TRANSFORMER
(MAIN)
Q507,508 PROTECT DETECT
R551
R548
100
4.7K
FAN DRIVE
R550
JR503
R549 100 15.1
0.22U
*
*CN906
4P:EXCEPT TH
2P:TH
IC501
*
POWER AMP
*
EXCEPT TH
*
*
*
-40.7
40.7
0
0
0
0
39.4
0
0
0
0.6
0
0
SUB TRANS BOARD
*CN905
4P:EXCEPT TH
2P:TH
S902
VOLTAGE SELECTOR
JR504
*
JR505
120V
EXCEPT TH
220P
220P
220V
230-240V
*
1K
*
10K
1K
0
0
0
9.7
MUTE
2SC3143S
2.7
3.2
47K
R520
10 1/2W
R521
10 1/2W
C524
0.1U
C523
0.1U
*
C526
0.1U
C525
0.1U
*
1000U
16V
Q502,503
OVER LOAD
DETECTOR
9.7
39.4
220P
2SC3143S
0
*
EXCEPT TH
JW901
JW902
56K
0.7
9.6
PWR AMP BOARD
JW903
JW904
0 0
JW905
0
JW906
JW907
0.6
JW908
FAN
SWITCH
No mark:FM
JW909
JW911
JW912
JW913
2P
2P
JW914
JW915
SENSOR (FAN)
BOARD
46
*
POWER TRANSFORMER
(SUB)
47K
Q504,506
OVER HEAT
DETECTOR
JW912 *
*
*
46
TH
*
HCD-HP8V
8-16. IC Block Diagrams
— BD Board —
IC103 CXA2581N-T4
RW/ROM
A
30 DC OFST
29 RFDCI
–
+
B
–
+
28 RFDCO
C
D
DVC
DVC
VCC
VC
–
+
DVC
VC
RW/ROM
VOFST
27 VC
VC
LD
1
PD
2
EQ IN
3
EQ
26 RFC
25 VFC
24 BST
RFAC
VCA
23 RFG
VCC
22 VCC
APC AMP
EQ ON/OFF
RW/ROM
5
A
B
C D
21 CEI
–
+
— PANEL Board —
IC002 M65850FP
20 CE
D
REF
OP2IN
OP2OUT
LPF2IN
LPF2OUT
DVC
A
B
C
D
6
7
8
9
VOFST
–
+
CLOCK
A
A
B
C
D
B
C
VCC
GND
RFAC
SUMMING
AMP
4
NC
AC SUM
16
15
14
13
12
11 10
9
VC
RW/ROM
19 TE BAL
RW/ROM
OSCILLATOR
E 10
GM
SW 12
APC-OFF
(Hi-Z)
RW/ROM
(H/L)
LPF2
1/2 VCC
GM
F 11
D/A
–
+
DO1
CLOCK
18 TE
AUTO
RESET
RESET
MAIN
CONTROL
D1
DO0
MO
20KBIT
SRAM
MI
VC
A/D
RW/ROM
LPF1
DVC 14
A
–
+
4
5
6
7
8
OP1OUT
OP1IN
CC1
CC2
GND
17 FEI
VOFST
–
+
3
LPF1OUT
D
2
LPF1IN
B
DVC
1
NC
RW/ROM
DVCC 13
16 FE
C
DVC
VC
IC602 MM1574A
RW/ROM
RFAC 15
VIN 1
5
VO
4
NOISE
BIAS
GND 2
DRIVER
REFERENCE
CURRENT
LIMITTER
THERMAL
SHUTDOWN
CONT 3
47
HCD-HP8V
— VMP Board —
GND
AO1
DI
CLK
LD
AO6
VCC
IC506 BU2507FV-E2
14
13
12
11
10
9
8
14BIT
SHIFT REGISTER
10BIT R-2R
D/A CONVERTER
D0 – D9
10BIT R-2R
D/A CONVERTER
D10 – D13
CH1
ADDRESS
DECODER
10BIT LATCH
10BIT LATCH
CH6
10BIT R-2R
D/A CONVERTER
10BIT R-2R
D/A CONVERTER
10BIT R-2R
D/A CONVERTER
10BIT R-2R
D/A CONVERTER
1
2
3
4
5
6
7
RESET
AO4
AO5
VDD
(VREFH)
10BIT LATCH
CH5
AO3
10BIT LATCH
CH4
AO2
10BIT LATCH
CH3
VSS
(VREFL)
10BIT LATCH
CH2
IC307 BD7600FV-E2
8dB
BUFOUT 1
8 BUFIN
VCC
CLAMP
STBY 2
LPF
IN 3
GND 4
SCK
ML
MC
MD
ZEROL
ZEROR
VCOM
AGND
IC504 PCM1748E/2K
16
15 14 13
12
11
10
9
SYSTEM
CLOCK
MANAGER
FUNCTION
CONTROL
INTERFACE
SYSTEM
CLOCK
SERIAL
INPUT
INTERFACE
8 TIME OVER
SAMPLING
DIGITAL FILTER
WITH
FUNCTION
CONTROLLER
D/A
CONVERTER
OUTPUT AMP AND
LOW-PASS FILTER
D/A
CONVERTER
OUTPUT AMP AND
LOW-PASS FILTER
ENHANCED
MULTI-LEVEL
DELTA-SIGMA
MODULATOR
48
1 2 3
4
5
6
7 8
BCK
DATA
LRCK
DGND
VDD
VCC
VOUTL
VOUTR
POWER SUPPLY
9dB
6 OUT
5 OUTSAG
GND
ZERO DETECT
7 VCC
HCD-HP8V
— MAIN Board —
IC201 HA12237F
— PWR AMP Board —
IC501 STK403-070S
PRE DRIVER
CH1
PRE DRIVER
CH2
BIAS
CIRCUIT
13 14
CH2 NF
CH2 IN
12
ST-BY
5 6 7 8 9 10 11
CH2 OUT(+)
CH2 OUT(-)
+PRE
SUB
GND
CH1 IN
CH1 NF
+VCC
3 4
CH1 OUT(+)
CH1 OUT(-)
2
-VCC
SUB
1
— CONNECTOR Board —
IC701, 711, 721 BA6956AN
TSD
1
2
3
4
5
6
7
8
9
VREF
OUT2
RNF
OUT1
VM
VCC
FIN
GND
RIN
CONTROL LOGIC
49
HCD-HP8V
8-17. IC Pin Function Description
• IC601
Pin No.
LC876796B-51Y2-E (SYSTEM CONTROLLER)(PANEL BOARD)
Pin Name
I/O
Description
1
SYS MUTE
O
System muting signal output
2
BU1924 DATA
I
RDS data input from the tuner
3
CD POWER
O
CD power supply on/off control signal output
4
SYS-RESET
O
System reset signal output
5
SYS-CE
O
Chip enable signal output to the IC505
6
SYS-REQ
O
Request signal output to the IC505
7
M61529 CLK
O
Clock output to the sound processor (IC301)
8
PT8300 CE
O
Chip enable signal output to the I/O expander (IC302)
9
LC72121 CE
O
Chip enable signal output to the tuner
10
SYS-OK
O
Acknowledge signal output to the IC505
11
RESET
I
Reset signal input
12
XT1
I
Resonator terminal (32.768kHz)
13
XT2
O
Resonator terminal (32.768kHz)
14
VSS1
—
Ground terminal
15
CF 1
I
Resonator terminal (8MHz)
16
CF 2
O
Resonator terminal (8MHz)
17
VDD1
—
Power supply terminal
18
TCM
I
Switch detection signal input from the tape deck
19
TCM1
I
Switch detection signal input from the tape deck
20
CDM ELVE-3,2,1
I
Sensor signal input from the CD changer
I
Sensor signal input from the CD changer
21
CDM ELVE-0/
SLDE-3,2
22
CDM SLDE-1,0
I
Sensor signal input from the CD changer
23
VACS
I
VACS signal input
24
KEY 2
I
Key signal input from the S614 to 622
25
KEY 1
I
Key signal input from the S601 to 610
26
KEY 0
I
Key signal input from the S627 to 636
27
POWER DOWN
I
Power down detection signal input from the IC603
28
REMCON IN
I
Remote control signal input from the remote sensor (RM601)
29
BU1924 CLK
I
RDS clock input from the tuner
30 to 41
G12 to G1
O
Grid signal output to the fluorescent indicator tube
42 to 45
P1 to P4
O
Segment output to the fluorescent indicator tube
46
VDD3
—
Power supply terminal
47 to 50
P5 to P8
O
Segment output to the fluorescent indicator tube
51
VPP
—
Power supply terminal (negative)
52 to 65
P9 to P22
O
Segment output to the fluorescent indicator tube
66
CDM SW5-B
I
Stocker in/out switch signal input from the CD changer
67
CDM SW5-A
I
Disc position switch signal input from the CD changer
68
CDM SW4
I
Stocking switch signal input from the CD changer
69
CDMSW2-B
I
Disc in (8cm) switch signal input from the CD changer
70
CDM SW2-A
I
Disc in (play) switch signal input from the CD changer
71
CDMSW1-A
I
Disc insert switch signal input from the CD changer
72
VDD4
—
73
CDM SW3
I
Disc out switch signal input from the CD changer
74
TUNER TUNED
I
Tuner tuned status signal input from the tuner
75
TUNER STEREO
I
Stereo/mono signal input from the tuner
76
VIDEO-MUTE
O
Video muting signal output to the video amplifier (IC307)
77
VIDEO-SW
O
Not used (open)
78
CD MUTE
O
CD muting signal output
79
VR ENCODER A
I
Volume signal input from the rotary encoder (VR601)
50
Power supply terminal
HCD-HP8V
Pin No.
Pin Name
I/O
80
VR ENCODER B
I
Volume signal input from the rotary encoder (VR601)
81
CDM D.SENSOR
I
Disc detection signal input
82
PROTECTOR
I
Protection signal input from the power amplifier circuit
83
TAPE END
I
Tape end detection signal input from the tape deck
84
MODE SW IN
I
Mode setting signal input
85
LINE OUT MUTE
O
Line out muting signal output
86
DISC5 LED
O
Disc LED control signal output
87
DISC4 LED
O
Disc LED control signal output
88
DISC3 LED
O
Disc LED control signal output
89
VSS2
—
Ground terminal
90
VDD2
—
Power supply terminal
91
DISC2 LED
O
Disc LED control signal output
92
DISC1 LED
O
Disc LED control signal output
93
POWER LED
O
Power LED control signal output
94
POWER RELAY
O
Power relay on/off control signal output
O
Data output to the tuner, the sound processor (IC301) and the I/O expander (IC302)
I
Data input from the tuner
O
Clock output to the tuner and the I/O expander (IC302)
O
Serial command data output to the IC505
95
96
97
98
LC72121/M61529/
PT8300 DO
LC72121 DI
LC72121/PT8300
CLK
SYS-OUT
Description
99
SYS-IN
I
Serial command data input from the IC505
100
SYS-CLK
O
Serial command clock output to the IC505
51
HCD-HP8V
• IC505 CXD1887R (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, MPEG VIDEO/AUDIO DECODER,
VIDEO SIGNAL ENCODER)(VMP BOARD)
Pin No.
Pin Name
I/O
Description
1
VB
O
Connected to ground via a capacitor
2
IREF
O
D/A converter reference current output
3
VRF
I
D/A converter reference voltage input
4
VG
O
Connected to the analog power supply (+2.5V) via a capacitor
5
XCPSIG
O
Luminance video composite/component signal invert output terminal Not used
6
CPSIG
O
Luminance video composite/component signal output
7
NC
O
Chrominance video composite signal output Not used
8
V AVD2
—
Analog power supply terminal (+2.5V) (for D/A converter)
9
V AVS2
—
Analog ground terminal (for D/A converter)
10
IVD1
—
Power supply terminal (+3.3V) (for I/O)
11
I2C CLK
I/O
Communication data reading clock signal input or transfer clock signal output terminal
Not used
12
I2C DATA
I/O
Communication data bus terminal Not used
13
GPIO0
I
Serial data input from the system controller
14
GPIO1
O
Serial data output to the system controller
15
GPIO2
O
Serial data transfer clock signal output to the system controller
16
GPIO3
I
Request signal input from the system controller
17
LVD1
—
18
GPIO4
I
Acknowledge signal input from the system controller
Digital power supply terminal (+2.5V) (for AV decoder block)
19
GPIO5
O
Chip select signal output to the system controller
20, 21
GPIO6, GPIO7
I/O
Not used
22
LVS1
—
Digital ground terminal (for AV decoder block)
23
GPIO8
I/O
Not used
24
GPIO9
O
Frequency selection signal output
25
GPIO10
I/O
Not used
26
GPIO11
O
Serial data latch pulse signal output to the digital filter
27
LVD2
—
Digital power supply terminal (+2.5V) (for AV decoder block)
28
GPIO12
O
Control signal output to the D/A converter
29
GPIO13
O
Serial data transfer clock signal output to the digital filter and D/A converter
30
GPIO14
O
Serial data output to the digital filter and D/A converter
31
IVS1
—
Ground terminal (for I/O)
32
LVS2
—
Digital ground terminal (for AV decoder block)
33
IVD2
—
Power supply terminal (+3.3V) (for I/O)
34 to 37
DRADR0 to
DRADR3
O
Address signal output to the D-RAM and program ROM
38
LVD3
—
Digital power supply terminal (+2.5V) (for AV decoder block)
39 to 45
DRADR4 to
DRADR10
O
Address signal output to the D-RAM and program ROM
46
LVS3
—
Digital ground terminal (for AV decoder block)
47
IVS2
—
Ground terminal (for I/O)
48
IVD3
—
Power supply terminal (+3.3V) (for I/O)
49 to 56
DRDAT0 to
DRDAT7
I/O
Two-way data bus with the D-RAM Data input from the program ROM
57
IVS3
—
Ground terminal (for I/O)
58
IVD4
—
Power supply terminal (+3.3V) (for I/O)
52
HCD-HP8V
Pin No.
Pin Name
I/O
Description
59 to 66
DRDAT8 to
DRDAT15
I/O
Two-way data bus with the D-RAM Data output to the program ROM
67
IVS4
—
Ground terminal (for I/O)
68
DRCAS
O
Column address strobe signal output to the D-RAM
69
LVD4
—
Digital power supply terminal (+2.5V) (for AV decoder block)
70
DRCK
O
Clock signal output to the D-RAM
71
IVD5
—
Power supply terminal (+3.3V) (for I/O)
72
DRRAS
O
Row address strobe signal output to the D-RAM
73
DRWEL
O
Write enable signal output to the D-RAM
74
NVOEL
O
Chip select signal output to the D-RAM
75
LVS4
—
Digital ground terminal (for AV decoder block)
76
DRBS
O
Bank select signal output to the D-RAM
77, 78
DRDQM0,
DRDQM1
O
Mask control signal output to the D-RAM
79
IVS5
—
Ground terminal (for I/O)
80
NC
—
Not used
81
SYSRST
I
Reset signal input from the system controller
82
IRDIN
I
IR data input terminal Not used
83
NC
—
Not used
84
VDD1
—
Digital power supply terminal (+2.5V) (for CD-DSP block)
85
V16M
O
Wide-band EFM PLL VCO2 oscillation output terminal Not used
86
DOUT
O
Digital audio signal output terminal Not used
87
L CDLRCK
I
L/R sampling clock signal (44.1 kHz) input
88
LRCK
O
L/R sampling clock signal (44.1 kHz) output
89
VSS1
—
Digital ground terminal
90
L CDDATA
I
Serial data input
91
PCMD
O
Serial data output
92
L CDBCK
I
Bit clock signal (2.8224 MHz) input
93
BCK
O
Bit clock signal (2.8224 MHz) output
94
EMPH
O
“L” is output when playback disc is emphasis off
“H” is output when playback disc is emphasis on Not used
95
L SQSO
I
Subcode-Q 80-bit, PCM peak and level data, CD text data input
96
SQSO
O
Subcode-Q 80-bit, PCM peak and level data, CD text data output
97
VDD2
—
Digital power supply terminal (+2.5V) (for CD-DSP block)
98
L SQCK
O
SQSO readout clock signal output
99
SQCK
I
SQSO readout clock signal input
100
SBSO
O
Subcode P to W serial data output terminal Not used
101
EXCK
I
SBSO readout clock signal input terminal Not used
102
DATA
I
Serial data input
103
L DDAT
O
Serial data output
104
VSS2
—
Digital ground terminal
105
L CDXRST
O
Reset signal output
106
XRST
I
Reset signal input
107
MUTE
I
Muting on/off control signal input terminal
108
L XLAT
O
Serial data latch pulse signal output
“L”: reset
“L”: reset
“L”: reset
“H”: muting on Not used
53
HCD-HP8V
Pin No.
Pin Name
I/O
109
XLAT
I
Serial data latch pulse signal input
110
L DCLK
O
Serial data transfer clock signal output
111
CLOK
I
Serial data transfer clock signal input
112
L SENS
I
SENS signal input
113
SENS
O
SENS signal output
114
L SLCK
O
SENS serial data readout clock signal output
115
SCLK
I
SENS serial data readout clock signal input
54
Description
116
VDD3
—
Digital power supply terminal (+2.5V) (for CD-DSP block)
117
ATSK
I/O
Input/output terminal for anti-shock Not used
118
XUGF
O
XUGF signal output terminal Not used
119
XPCK
O
XPCK signal output terminal Not used
120
L GFS
I
Guard frame sync signal input
121
GFS
O
Guard frame sync signal output
122
VSS3
—
Digital ground terminal
123
L CDC2PO
I
C2 pointer signal input
124
C2PO
O
C2 pointer signal output
125
L SCOR
I
Subcode sync (S0+S1) detection signal input
126
SCOR
O
Subcode sync (S0+S1) detection signal output
127
COUT
O
Numbers of track counted signal output terminal Not used
128
VDD4
—
Digital ground terminal (for CD-DSP block)
129
MIRR
I/O
Mirror signal input/output terminal Not used
130
DFCT
I/O
Defect signal input/output terminal Not used
131
L FOK
I/O
Focus OK signal input/output
132
FOK
I/O
Focus OK signal input/output
133
MDP
O
Spindle motor servo drive signal output
134
VSS4
—
Digital ground terminal
135
SSTP
I
Detection signal input from limit in switch The optical pick-up is inner position when “H”
136
FSTO
O
2/3 frequency-division output of the XTAI (pin <zv. )
137
SFDR
O
Sled motor servo drive signal (+) output
138
SRDR
O
Sled motor servo drive signal (–) output
139
VDD5
—
Digital power supply terminal (+2.5V) (for CD-DSP block)
140
TFDR
O
Tracking coil servo drive signal (+) output
141
TRDR
O
Tracking coil servo drive signal (–) output
142
FFDR
O
Focus coil servo drive signal (+) output
143
FRDR
O
Focus coil servo drive signal (–) output
144
VSS5
—
Digital ground terminal
145
WFCK
O
Write frame clock signal output terminal Not used
146
WDCK
O
Word clock signal output terminal Not used
147
ASYE
I
Asymmetry circuit on/off control signal input terminal “L”: off, “H”: on
148
VDD6
—
149
XTAI
I
Main system clock input terminal (33.8688 MHz)
150
XTAO
O
Main system clock output terminal (33.8688 MHz)
151
VSS6
—
Digital ground terminal
152
TES1
I
Input terminal for the test Normally: fixed at “L”
153
TEST
I
Input terminal for the test Normally: fixed at “L”
Not used
Digital power supply terminal (+2.5V) (for CD-DSP block)
HCD-HP8V
Pin No.
Pin Name
I/O
Description
154, 155
NC
—
Not used
156
AVD0
—
Analog power supply terminal (+2.5V)
157
IGEN
I
158
AVS0
—
Analog ground terminal
159
ADIO
O
Output terminal for the test Not used
160
RFDC
I
RF signal input from the RF amplifier
161
CE
I
Center servo analog signal input
162
TE
I
Tracking error signal input from the RF amplifier
163
SE
I
Sled error signal input from the RF amplifier
164
FE
I
Focus error signal input from the RF amplifier
165
VC
I
Center voltage (+1.65V) input terminal
166
VPCO
O
Wide-band EFM PLL charge pump output
167
VCTL
I
Wide-band EFM PLL VCO2 control voltage input
168
FILO
O
Master PLL filter output
Operational amplifier constant current input
169
FILI
I
Master PLL filter input
170
PCO
O
Master PLL charge pump output
171
CLTV
I
Multiplier VCO1 control voltage input
172
AVS1
—
173
RFAC
I
EFM signal input from the RF amplifier
174
BIAS
I
Asymmetry circuit constant current input
Analog ground terminal
175
ASYI
I
Asymmetry comparator voltage input
176
ASYO
O
EFM full-swing output
177
AVD1
—
Analog power supply terminal (+2.5V)
178
VDD7
—
Digital power supply terminal (+2.5V) (for CD-DSP block)
179
SOUT
O
Serial data output terminal Not used
180
SOCK
O
Serial data readout clock signal output terminal Not used
181
XOLT
O
Serial data latch pulse signal output terminal Not used
182
C4M
O
4.2336 MHz clock signal output terminal Not used
183
LOCK
O
GFS is sampled by 460 Hz “H” output when GFS is “H” Not used
184
VSS7
—
Digital ground terminal
185
MD2
I
Digital out on/off control signal input terminal “L”: digital out off, “H”: digital out on
Not used
186
SCSY
I
Guard subcode sync (S0+S1) resynchronization input terminal Not used
187
PWMI
I
Spindle motor external control signal input terminal Not used
188
VDD8
—
189
XTSL
I
190
VSS8
—
Digital ground terminal
191
PVS2
—
Analog ground terminal (for PLL2)
Digital power supply terminal (+2.5V) (for CD-DSP block)
Input terminal for the system clock frequency setting
“L”: 16.9344 MHz, “H”: 33.8688MHz
192
LPFI
I
Connected terminal of PLL2 filter
193
LPFO
O
Connected terminal of PLL2 filter
194
PVD2
—
Analog power supply terminal (+2.5V) (for PLL2)
195, 196
NC
—
Not used
197
PVD1
—
Analog power supply terminal (+2.5V) (for PLL1)
198
PVS1
—
Analog ground terminal (for PLL1)
55
HCD-HP8V
Pin No.
Pin Name
I/O
199
TMODE0
I
Selection signal input terminal for the test Not used
200
AUDDTI
I
Serial audio data input terminal Not used
201
AUDDTO0
O
Serial audio data output to the digital filter
202
AUDDTO1
O
Serial audio data output terminal Not used
203
AUDBCK
O
Serial audio bit clock signal (2.8224 MHz) output to the digital filter
204
AUDLRCK
O
Serial audio L/R sampling clock signal (44.1 kHz) output to the digital filter
205
AUDXCLKO
O
Serial audio clock signal output to the digital filter
206
CLKA
I
Sub system clock input terminal (27 MHz)
207
CLKB
O
Sub system clock output terminal (27 MHz)
208
VDD9
—
Digital power supply terminal (+2.5V) (for CD-DSP block)
209
THRCLK
I
Clock signal input terminal for the test Not used
210
TESTEN
I
Setting terminal for the test Normally: fixed at “L”
211
TCLK
I
Clock signal input terminal for the test Not used
212
TMODE1
I
Selection signal input terminal for the test Not used
213
TRST
I
Reset signal input terminal for the test Not used
214
VSS9
—
Digital ground terminal
215
V AVS1
—
Analog ground terminal (for D/A converter)
216
V AVD1
—
Analog power supply terminal (+2.5V) (for D/A converter)
56
Description
HCD-HP8V
SECTION 9
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
The mechanical parts with no reference number
in the exploded views are not supplied.
Abbreviation
E3 : 220-240 V AC area in E model.
EA : Saudi Arabia model.
SP : Singapore model.
TH : Thai model.
•
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
9-1. Case, Top Panel Section
4
8
9
#2
3
10
14
5
14
1
#2
2
6
11
6
7
1
12
#1
6
#2
#1
6
not
supplied
1
13
#1
chassis section
1
front panel section
#1
Ref. No.
Part No.
Description
1
2
3
4
5
3-363-099-71
4-246-394-11
4-246-395-01
4-246-396-01
4-232-195-01
SCREW (CASE 3 TP2)
CASE (SIDE-L)
LID (TC)
WINDOW (TC)
SPRING (LID)
6
7
8
4-951-620-01 SCREW (2.6X8), +BVTP
4-231-776-01 SPRING, CASSETTE DETENT
4-246-390-01 PANEL (L), SUB TOP
Remark
Ref. No.
Part No.
Description
9
10
11
12
13
4-246-389-11
4-246-391-01
1-827-392-11
1-796-351-41
4-246-393-11
PANEL, TOP
PANEL (R), SUB TOP
WIRE (FLAT TYPE)(8 CORE)
MECHANISM, SIGNAL CASSETTE
CASE (SIDE-R)
14
#1
#2
4-246-403-01 SPACER
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
Remark
57
HCD-HP8V
9-2. Front Panel Section
63
60
59
64
58
65
66
55
61
57
56
62
71
54
66
55
57
66
53
67
68
52
Ref. No.
69
70
51
Remark
Part No.
Description
Part No.
Description
51
52
53
54
55
4-225-252-01
4-246-397-01
4-246-384-01
4-246-385-01
4-246-382-01
CUSHION (FOOT)
EMBLEM (5CD)
KNOB (VOL)
RING (VOL)
BUTTON (FUNCTION)
63
64
64
64
65
1-769-920-11
A-4747-557-A
A-4747-565-A
A-4747-569-A
1-827-395-11
WIRE (FLAT TYPE)(9 CORE)
PANEL BOARD, COMPLETE (E3,SP)
PANEL BOARD, COMPLETE (EA)
PANEL BOARD, COMPLETE (TH)
WIRE (FLAT TYPE)(37 CORE)
56
57
58
59
60
4-246-374-31
4-246-383-01
4-246-379-01
4-246-378-01
4-246-381-01
PANEL, FRONT
BUTTON (PRESET)
BUTTON (POWER)
INDICATOR (POWER)
BUTTON (PLAY)
66
67
68
69
70
4-951-620-01
4-246-388-01
4-246-387-01
4-246-386-01
4-246-375-01
SCREW (2.6X8), +BVTP
BUTTON (EJECT)
INDICATOR (DISC)
BUTTON (DISC)
PANEL, SUB
61
62
4-246-376-01 WINDOW (DISPLAY)
4-246-380-01 BUTTON (DISPLAY)
71
4-246-408-01 KNOB (MIC)
58
Ref. No.
Remark
HCD-HP8V
9-3. Chassis Section-1
not
supplied
103
#3
101
#1
#1
#3
#1
#1
T901
#7
not
supplied
105
#9
#9
#1
102
F904
F905
F903
#8
F901
F902
104
#1
107
#1
106
108
109
#1
chassis section
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
102
102
103
104
1-689-250-11
A-4734-342-A
A-4747-550-A
1-689-248-12
1-689-246-12
PWR TRANS BOARD
PWR AMP BOARD, COMPLETE (EXCEPT TH)
PWR AMP BOARD, COMPLETE (TH)
SENSOR (FAN) BOARD
SUB TRANS BOARD
0 F902
0 F903
0 F904
0 F905
0 T901
1-533-473-11
1-533-470-11
1-533-470-11
1-533-471-11
1-439-834-11
FUSE, GLASS TUBE (DIA. 5)
FUSE, GLASS TUBE (DIA. 5)
FUSE, GLASS TUBE (DIA. 5)
FUSE, GLASS TUBE (DIA. 5)(EXCEPT TH)
TRANSFORMER, POWER (EXCEPT EA)
105
106
107
108
109
1-787-025-11
4-225-252-01
1-693-628-11
1-769-946-11
A-4747-562-A
DC FAN
CUSHION (FOOT)
TUNER (FM/AM)
WIRE (FLAT TYPE)(11 CORE)
MAIN BOARD, COMPLETE (EXCEPT TH)
0 T901
#1
#3
#7
#8
1-439-835-11
7-685-646-79
7-685-881-09
7-682-552-09
7-685-647-79
TRANSFORMER, POWER (EA)
SCREW +BVTP 3X8 TYPE2 IT-3
SCREW +BVTT 4X8 (S)
SCREW +B 3X16
SCREW +BVTP 3X10 TYPE2 IT-3
109
0 F901
A-4747-574-A MAIN BOARD, COMPLETE (TH)
1-533-473-11 FUSE, GLASS TUBE (DIA. 5)
Remark
#9
Remark
7-684-023-04 N 3, TYPE 2
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
59
HCD-HP8V
9-4. Chassis Section-2
151
152
not
supplied
#1
153
not
supplied
#1
#1
CD mechanism deck section-1
not
supplied
a
158
#1
155
156
not
supplied
#8
#1
160
a
not
supplied
161
157
Ref. No.
Part No.
Description
0 151
0 151
0 151
152
* 152
1-824-818-11
1-783-532-11
1-791-901-12
3-703-571-11
3-703-244-00
CORD, POWER (WITH CONNECTOR)(TH)
CORD, POWER (EA,SP)
CORD, POWER (E3)
BUSHING (S)(4516), CORD (E3)
BUSHING (2104), CORD (EXCEPT E3)
153
155
156
4-988-533-01 HOLDER, PWB
1-827-390-11 WIRE (FLAT TYPE)(27 CORE)
1-827-391-11 WIRE (FLAT TYPE)(28 CORE)
Remark
Ref. No.
Part No.
Description
157
158
160
160
161
3-378-109-12
1-689-247-12
A-4747-564-A
A-4747-576-A
1-827-394-11
CUSHION, SARANET
JACK BOARD
VMP BOARD, COMPLETE (EXCEPT TH)
VMP BOARD, COMPLETE (TH)
WIRE (FLAT TYPE)(19 CORE)
#1
#8
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
Remark
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
60
HCD-HP8V
9-5. CD Mechanism Section-1 (CDM69BH-30BD62)
not supplied
304
302
#4
301
S702
303
#4
M761
306
not
supplied
312
302
not supplied
308
CD mechanism deck section-2
309
307
302
310
#4
Ref. No.
Part No.
Description
301
302
303
306
307
1-686-725-12
4-951-620-01
4-239-690-01
4-239-687-01
A-4731-113-A
STOCKER MOTOR BOARD
SCREW (2.6X8), +BVTP
CAM (STOCKER U/D)
GEAR (STOCKER COMMUNICATION)
CONNECTOR BOARD, COMPLETE
308
4-239-689-01 GEAR (STOCKER DECELERATION)
Remark
Ref. No.
Part No.
Description
Remark
309
310
312
M761
S702
4-239-698-01
4-211-237-01
4-986-156-01
A-4735-953-A
1-477-299-11
PULLEY (STOCKER)
BELT (MODE)
PULLEY, MOTOR
MOTOR ASSY (STOCKER)
ENCODER, ROTARY (STOCKER POSITION)
#4
7-685-902-21 SCREW +PTPWH 2.6X8 (TYPE2)
61
HCD-HP8V
9-6. CD Mechanism Section-2 (CDM69BH-30BD62)
352
353
354
355
#5
355
351
CD mechanism deck section-3
357
CD mechanism deck section-4
356
optical pick-up
section
Ref. No.
351
352
353
354
62
Part No.
Description
1-686-727-12
1-686-728-12
1-686-729-12
1-686-730-12
SW (1) BOARD
SW (2) BOARD
SW (3) BOARD
SW (4) BOARD
Remark
Ref. No.
355
356
357
#5
Part No.
Description
4-951-620-01
4-985-672-01
4-227-899-01
7-685-533-14
SCREW (2.6X8), +BVTP
SCREW (+PTPWHM2.6), FLOATING
SCREW (DIA. 12), FROATING
SCREW +BTP 2.6X6 TYPE2 N-S
Remark
HCD-HP8V
9-7. CD Mechanism Section-3 (CDM69BH-30BD62)
407
not supplied
406
not
supplied
not supplied
405
409
421
413
not
supplied
411
420
409
408
415
425
402
412
not
supplied
405
414
415
416
not supplied
404
418
403
404
419
402
402
422
418
423
418
424
402
417
418
402
401
Ref. No.
Part No.
Description
401
402
403
404
405
X-4955-447-1
4-992-069-01
4-239-648-01
4-239-646-01
4-239-641-01
PULLEY (A)(BU30) ASSY,CHUCKING
SCREW (+PTPWH)(M2)(DIA. 7)
PARASOL (ROLLER)
ROLLER (ROLLER)
SPRING (1.2), TENSION
406
407
408
409
411
4-239-642-01
4-239-679-01
4-243-714-01
4-239-649-01
4-244-035-01
SPRING (3), TENSION COIL
SPRING (5), TENSION COIL
PULLEY (B)(BU30), CHUCKING
PARASOL (STOCKER)
ROLLER (STOCKER), RUBBER
412
413
4-239-640-02 PINION (SLIDER)
4-243-291-01 SPRING (HELPER2), TENSION
Remark
Ref. No.
Part No.
Description
414
415
416
417
418
4-240-039-01
4-239-702-01
4-985-672-01
4-243-713-01
4-239-647-01
LEVER (DISC STOPPER)
ROLLER (DISC STOPPER)
SCREW (+PTPWHM2.6), FLOATING
LEVER (LIFTER)
PARASOL (MAIN)
419
420
421
422
423
4-243-916-01
4-241-599-01
4-239-643-01
4-228-414-01
4-244-032-01
ROLLER (S), RUBBER
LEVER (SUPPORT)
SPRING (4), TENSION COIL
BRACKET (YOKE)
ROLLER, RUBBER
424
425
4-231-505-01 SPACER (CH)
4-240-040-01 SPRING, TORSION
Remark
63
HCD-HP8V
9-8. CD Mechanism Section-4 (CDM69BH-30BD62)
#6
457
#6
457
467
454
457
453
456
455
455
#6
457
456
454
451
470
471
462
455
456
463
461
464
453
not
supplied
465
475
457
458
469
468
452
461
452
461
466
451
461
457
456
455
#6
458
453
456
457
470
#6
457
452
458
#6
457
454
458
460
466
455
472
454
453
473
not
supplied
474
452
M781
451
CD mechanism deck section-5
Ref. No.
Part No.
Description
451
452
453
454
455
X-4954-626-1
4-239-666-01
4-239-668-01
4-239-652-01
4-239-669-01
LEVER (ROLLER) ASSY
GEAR
LEVER (CENTER)
SCREW (ROLLER), STEP
GEAR (ROLLER COMMUNICATION)
456
457
458
460
461
4-239-667-01
4-239-647-01
4-244-032-01
X-4954-622-1
4-239-670-01
462
463
464
465
X-4954-624-A
4-992-069-01
4-240-981-01
4-240-041-01
64
Remark
Ref. No.
Part No.
Description
466
467
468
469
470
4-951-620-01
4-243-916-01
4-244-035-01
4-241-209-01
4-239-649-01
SCREW (2.6X8), +BVTP
ROLLER (S), RUBBER
ROLLER (STOCKER), RUBBER
SHEET, ADHESIVE
PARASOL (STOCKER)
GEAR (ROLLER CENTER)
PARASOL (MAIN)
ROLLER, RUBBER
BASE (SLIDER 2) ASSY
GEAR (ROLLER 5 COMMUNICATION)
471
472
473
474
475
4-239-671-01
X-4954-627-1
1-686-726-12
4-986-156-01
4-244-162-01
GEAR (ROLLER 5 CENTER)
BASE (SLIDER 5) ASSY
ROLLER MOTOR BOARD
PULLEY, MOTOR
SPRING (SLIDER 4),TENSION
LEVER (SLIDER 4) ASSY
SCREW (+PTPWH)(M2)(DIA. 7)
SPRING (BASE SLIDER 5),TENSION
SPRING (SLIDER 2), TENSION
M781
#6
A-4735-953-A MOTOR ASSY (ROLLER)
7-623-921-01 RING, RETAINING, CAPSTAN
4-240-040-01 SPRING (DISC STOPPER), TORSION
Remark
HCD-HP8V
9-9. CD Mechanism Section-5 (CDM69BH-30BD62)
504
503
505
503
505
501
502
506
CD mechanism sdeck ection-6
507
509
508
Ref. No.
501
502
503
504
505
Part No.
Description
4-240-020-01
4-239-708-02
4-239-697-01
X-4955-15701
4-239-706-02
GEAR (TIMING)
BELT (FRONT), TIMING
GEAR (CENTER)
SLIDER (MODE CAM V) ASSY
BELT (REAR), TIMING
Remark
Ref. No.
506
507
508
509
#4
#4
Part No.
Description
4-239-699-01
4-247-349-02
4-227-899-01
4-239-686-01
7-685-902-21
PULLEY
BELT (ROLLER V)
SCREW (DIA. 12), FROATING
GEAR (ROLLER DECELERATION)
SCREW +PTPWH 2.6X8 (TYPE2)
Remark
65
HCD-HP8V
9-10. CD Mechanism Section-6 (CDM69BH-30BD62)
563
575
M771
not
supplied
565
not supplied
576
551
#4
#4
554
#4
#4
553
569
#4
564
555
555
558
560
not
supplied
570
557
#4
572 562
563
559
552
567
563
563
#4
#4
S771
561
571
566
#4
#4
Ref. No.
Part No.
Description
Part No.
Description
551
552
553
554
555
4-239-693-02
1-686-723-12
4-239-696-01
4-239-695-02
4-240-019-01
CAM (GEAR)
SENSOR BOARD
GEAR (EJECT LOCK)
CAM (EJECT LOCK)
GEAR (MODE 5)
565
566
567
569
570
4-239-694-01
4-241-731-01
4-241-732-01
4-241-734-01
4-241-735-01
GEAR (MODE CAM)
SHUTTER (A), LEVER
SHUTTER (B), LEVER
SHAFT (SHUTTER)
SPRING (SHUTTER), COMPRESSION
557
558
559
560
561
4-243-682-01
4-239-683-01
4-243-702-01
4-243-683-01
4-239-618-01
GEAR (MODE C)
PULLEY (MODE DECELERATION)
BELT (MODE V)
GEAR (MODE D)
SCREW (+PWH,2X6), STEP TAPPING
571
572
575
576
M771
4-227-899-01
4-243-680-01
1-686-724-12
4-986-156-01
A-4735-953-A
SCREW (DIA. 12), FROATING
GEAR (MODE A)
MODE MOTOR BOARD
PULLEY, MOTOR
MOTOR ASSY (MODE)
562
563
564
4-243-681-01 GEAR (MODE B)
4-951-620-01 SCREW (2.6X8), +BVTP
4-239-692-02 CAM (BU U/D)
S771
#4
1-477-300-11 ENCODER, ROTARY (MODE)
7-685-902-21 SCREW +PTPWH 2.6X8 (TYPE2)
66
Remark
Ref. No.
Remark
HCD-HP8V
9-11.
Base Unit Section (BU-30BD62)
605
604
606
605
605
604
604
605
607
604
603
610
602
601
Ref. No.
601
602
603
604
Part No.
Description
4-243-716-01
4-244-556-01
A-4728-371-A
4-231-451-01
HOLDER (BU-30)
SPRING (FRONT), COMPRESSION
BD BOARD, COMPLETE
INSULATOR (BU-30)
Remark
Ref. No.
Part No.
Description
Remark
605
606
0 607
610
4-985-672-01
1-782-817-11
A-4735-189-A
4-227-045-31
SCREW (+PTPWH M2.6), FLOATING
WIRE (FLAT TYPE)(16 CORE)
BU-30 (61) ASSY (including M101, M102)
SPRING (INSULATOR), COIL
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
67
HCD-HP8V
BD
SECTION 10
ELECTRICAL PARTS LIST
CONNECTOR
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they may
have some difference from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
• CAPACITORS:
uF: µF
• COILS
uH: µH
Ref. No.
Part No.
•
•
•
Accessories are given in the last of this parts
list.
RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
Description
Remarks
A-4728-371-A BD BOARD, COMPLETE
*******************
Ref. No.
Q102
Part No.
•
Abbreviation
E3 : 220-240 V AC area in E model.
EA : Saudi Arabia model.
SP : Singapore model.
TH : Thai model.
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Description
8-729-424-08 TRANSISTOR
Remarks
UN2111-TX
< RESISTOR >
< CAPACITOR/JUMPER RESISTOR >
C101
C102
C103
C104
C107
1-164-315-11
1-107-826-11
1-164-315-11
1-162-967-11
1-162-921-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
0.1uF
470PF
0.0033uF
33PF
5.00%
10.00%
5.00%
10%
5%
C108
C109
C110
C111
C112
1-164-360-11
1-164-360-11
1-107-826-11
1-126-607-11
1-126-607-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
0.1uF
0.1uF
0.1uF
47uF
47uF
16V
16V
10.00% 16V
20%
4V
20%
4V
C113
C114
C115
C117
C118
1-126-209-11
1-162-964-11
1-126-205-11
1-164-360-11
1-115-156-11
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.001uF
47uF
0.1uF
1uF
20.00% 4V
10%
50V
20%
6.3V
16V
10V
C119
C120
C151
C153
C163
1-115-156-11
1-126-607-11
1-164-227-11
1-164-360-11
1-128-995-21
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
1uF
47uF
0.022uF
0.1uF
100uF
10V
4V
25V
16V
10V
C164
C165
C166
C182
C213
1-164-360-11
1-124-779-00
1-164-360-11
1-128-995-21
1-216-864-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
METAL CHIP
0.1uF
10uF
0.1uF
100uF
0
20%
10%
20%
20%
20%
5%
< CONNECTOR >
CN101
CN102
1-784-877-21 CONNECTOR,FFC (LIF (NON-ZIF)) 28P
1-794-424-11 CONNECTOR, FCC/FPC 16P
50V
16V
50V
50V
50V
16V
16V
16V
10V
1/10W
R102
R103
R104
R105
R109
1-216-835-11
1-216-845-11
1-216-835-11
1-216-821-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
100K
15K
1K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R111
R112
R113
R114
R117
1-216-846-11
1-216-864-11
1-216-826-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120K
0
2.7K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R118
R120
R122
R123
R124
1-216-864-11
1-216-846-11
1-216-845-11
1-216-797-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
120K
100K
10
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R125
R126
R151
R152
R176
1-216-839-11
1-216-839-11
1-216-845-11
1-216-829-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
33K
100K
4.7K
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R179
R227
R228
R229
R231
1-216-833-11
1-216-845-11
1-216-853-11
1-216-825-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
470K
2.2K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R234
1-216-864-11 METAL CHIP
0
5%
1/10W
R235
1-216-821-11 METAL CHIP
1K
5%
1/10W
R236
1-216-821-11 METAL CHIP
1K
5%
1/10W
************************************************************
A-4731-113-A CONNECTOR BOARD, COMPLETE
***************************
< DIODE >
D101
8-719-988-61 DIODE 1SS355TE-17
< IC >
IC102
IC103
8-759-713-70 IC AN41020A
8-752-089-74 IC CXA2581N-T4
< CAPACITOR >
C711
C751
C752
C753
C754
1-126-795-11
1-164-159-21
1-164-159-21
1-164-159-21
1-164-159-21
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
10uF
0.1uF
0.1uF
0.1uF
0.1uF
20.00% 50V
50V
50V
50V
50V
C755
C756
1-164-159-21 CERAMIC
1-164-159-21 CERAMIC
0.1uF
0.1uF
50V
50V
< TRANSISTOR >
Q101
68
8-729-049-31 TRANSISTOR
2SB710A-RTX
HCD-HP8V
CONNECTOR
Ref. No.
Part No.
Description
Remarks
C758
C761
C762
1-164-159-21 CERAMIC
1-162-306-11 CERAMIC
1-164-159-21 CERAMIC
0.1uF
0.01uF
0.1uF
C763
C764
C765
C766
C767
1-164-159-21
1-164-159-21
1-164-159-21
1-164-159-21
1-164-159-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C768
C769
C771
C781
1-164-159-21
1-164-159-21
1-162-306-11
1-162-306-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
0.01uF
0.01uF
50V
30.00% 16V
50V
50V
50V
50V
50V
50V
50V
50V
30.00% 16V
30.00% 16V
< CONNECTOR >
CN701
CN702
CN703
* CN710
1-779-564-21
1-785-329-11
1-785-328-11
1-506-486-11
CONNECTOR,FFC (LIF (NON-ZIF)) 27P
PIN, CONNECTOR (LIGHT ANGLE) 3P
PIN, CONNECTOR (LIGHT ANGRE) 2P
PIN, CONNECTOR 7P
< DIODE >
D701
D711
D721
8-719-921-40 DIODE MTZJ-T-77-4.7B
8-719-109-89 DIODE MTZJ-T-77-5.6B
8-719-982-03 DIODE MTZJ-T-77-3.6A
< IC >
IC701
IC711
IC721
8-759-598-69 IC BA6956AN
8-759-598-69 IC BA6956AN
8-759-598-69 IC BA6956AN
< TRANSISTOR >
Q731
8-729-029-66 TRANSISTOR
RT1N141S-TP
< RESISTOR >
R701
R702
R711
R712
R721
1-249-415-11
1-247-807-31
1-249-415-11
1-247-807-31
1-249-415-11
CARBON
CARBON
CARBON
CARBON
CARBON
680
100
680
100
680
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W F
1/4W
1/4W F
R722
1-247-807-31 CARBON
100
5%
1/4W
R731
1-247-806-11 CARBON
91
5%
1/4W
R732
1-249-417-11 CARBON
1K
5%
1/4W F
R733
1-249-429-11 CARBON
10K
5%
1/4W
R734
1-249-429-11 CARBON
10K
5%
1/4W
************************************************************
1-689-247-12 JACK BOARD
***********
< JACK >
JK302 1-774-227-31 JACK, PIN 1P (VIDEO OUT)
************************************************************
A-4747-562-A MAIN BOARD, COMPLETE (EXCEPT TH)
A-4747-574-A MAIN BOARD, COMPLETE (TH)
**********************
4-229-123-01 HEAT SINK, V.OUT
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
Ref. No.
Part No.
JACK
MAIN
Description
Remarks
< CAPACITOR >
C201
C202
C203
C204
C205
1-162-964-11
1-162-964-11
1-126-947-11
1-126-947-11
1-126-960-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.001uF
0.001uF
47uF
47uF
1uF
10%
10%
20.00%
20.00%
20.00%
50V
50V
16V
16V
50V
C206
C207
C208
C209
C210
1-130-485-00
1-130-485-00
1-126-960-11
1-126-960-11
1-126-961-11
MYLAR
MYLAR
ELECT
ELECT
ELECT
0.015uF
0.015uF
1uF
1uF
2.2uF
5%
5%
20.00%
20.00%
20.00%
50V
50V
50V
50V
50V
C211
C212
C213
C214
C215
1-126-961-11
1-126-960-11
1-126-960-11
1-126-959-11
1-126-959-11
ELECT
ELECT
ELECT
ELECT
ELECT
2.2uF
1uF
1uF
0.47uF
0.47uF
20.00%
20.00%
20.00%
20.00%
20.00%
50V
50V
50V
50V
50V
C216
C217
C218
C219
C220
1-126-961-11
1-126-961-11
1-165-176-11
1-165-176-11
1-162-966-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2uF
2.2uF
0.047uF
0.047uF
0.0022uF
20.00%
20.00%
10.00%
10.00%
10%
50V
50V
16V
16V
50V
C221
C224
C225
C226
C227
1-162-966-11
1-126-963-11
1-126-933-11
1-126-963-11
1-128-551-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.0022uF
4.7uF
100uF
4.7uF
22uF
10%
20.00%
20.00%
20.00%
20.00%
50V
50V
16V
50V
25V
C228
C229
C235
C236
C237
1-162-966-11
1-162-966-11
1-130-479-00
1-130-485-00
1-130-485-00
CERAMIC CHIP
CERAMIC CHIP
MYLAR
MYLAR
MYLAR
0.0022uF
0.0022uF
0.0047uF
0.015uF
0.015uF
10%
10%
5%
5%
5%
50V
50V
50V
50V
50V
C238
C239
C240
C301
C302
1-130-485-00
1-126-963-11
1-126-964-11
1-126-964-11
1-126-964-11
MYLAR
ELECT
ELECT
ELECT
ELECT
0.015uF
4.7uF
10uF
10uF
10uF
5%
20.00%
20.00%
20.00%
20.00%
50V
50V
50V
50V
50V
C303
C305
C306
C307
C308
1-104-665-11
1-126-964-11
1-126-964-11
1-126-963-11
1-109-953-11
ELECT
ELECT
ELECT
ELECT
ELECT
100uF
10uF
10uF
4.7uF
2.2uF
20.00%
20.00%
20.00%
20.00%
20.00%
10V
50V
50V
50V
50V
C309
C310
C311
C312
C313
1-126-964-11
1-126-964-11
1-126-964-11
1-126-964-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
10uF
10uF
10uF
10uF
20.00%
20.00%
20.00%
20.00%
20.00%
50V
50V
50V
50V
50V
C314
C315
C317
C318
C319
1-126-964-11
1-126-956-91
1-126-964-11
1-126-964-11
1-136-161-00
ELECT
ELECT
ELECT
ELECT
FILM
10uF
0.1uF
10uF
10uF
0.047uF
20.00%
20.00%
20.00%
20.00%
5.00%
50V
50V
50V
50V
50V
C320
C321
C323
C324
C325
1-136-157-00
1-136-157-00
1-136-157-00
1-136-157-00
1-136-161-00
FILM
FILM
FILM
FILM
FILM
0.022uF
0.022uF
0.022uF
0.022uF
0.047uF
5.00%
5.00%
5.00%
5.00%
5.00%
50V
50V
50V
50V
50V
C326
1-136-161-00 FILM
0.047uF
5.00% 50V
69
HCD-HP8V
MAIN
Ref. No.
Part No.
Description
C327
C328
C329
C330
1-130-476-00
1-130-476-00
1-126-964-11
1-126-964-11
MYLAR
MYLAR
ELECT
ELECT
0.0027uF
0.0027uF
10uF
10uF
5%
5%
20.00%
20.00%
Remarks
50V
50V
50V
50V
C331
C332
C333
C334
C338
1-136-165-00
1-136-165-00
1-136-164-00
1-136-164-00
1-164-227-11
FILM
FILM
FILM
FILM
CERAMIC CHIP
0.1uF
0.1uF
0.082uF
0.082uF
0.022uF
5.00%
5.00%
5.00%
5.00%
10%
50V
50V
50V
50V
25V
C340
C341
C342
C343
C344
1-162-960-11
1-162-960-11
1-126-964-11
1-162-953-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
220PF
220PF
10uF
100PF
0.1uF
10%
10%
20.00%
5%
50V
50V
50V
50V
25V
C345
C346
C347
C348
C349
1-162-953-11
1-162-964-11
1-126-964-11
1-126-964-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
100PF
0.001uF
10uF
10uF
10uF
5%
10%
20.00%
20.00%
20.00%
50V
50V
50V
50V
50V
C350
C351
C352
C353
C354
1-126-964-11
1-162-964-11
1-162-964-11
1-162-962-11
1-162-962-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.001uF
0.001uF
470PF
470PF
20.00%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C355
C356
C357
C358
C359
1-162-962-11
1-162-962-11
1-126-933-11
1-162-960-11
1-162-960-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
470PF
470PF
100uF
220PF
220PF
10%
10%
20.00%
10%
10%
50V
50V
16V
50V
50V
C360
C361
C362
C363
C364
1-162-964-11
1-162-960-11
1-162-960-11
1-126-964-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.001uF
220PF
220PF
10uF
10uF
10%
10%
10%
20.00%
20.00%
50V
50V
50V
50V
50V
C365
C366
C367
C368
C369
1-162-964-11
1-164-156-11
1-162-960-11
1-162-960-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
220PF
220PF
0.1uF
10%
50V
25V
50V
50V
25V
C371
C372
C401
C402
C403
1-126-963-11
1-126-963-11
1-136-165-00
1-136-165-00
1-136-165-00
ELECT
ELECT
FILM
FILM
FILM
4.7uF
4.7uF
0.1uF
0.1uF
0.1uF
20.00%
20.00%
5.00%
5.00%
5.00%
50V
50V
50V
50V
50V
C404
C405
C406
C407
C408
1-136-165-00
1-126-768-11
1-126-943-11
1-126-964-11
1-126-964-11
FILM
ELECT
ELECT
ELECT
ELECT
0.1uF
2200uF
2200uF
10uF
10uF
5.00%
20.00%
20.00%
20.00%
20.00%
50V
16V
25V
50V
50V
C409
C411
C412
C413
C414
1-126-919-11
1-126-767-11
1-126-943-11
1-126-935-11
1-126-947-11
ELECT
ELECT
ELECT
ELECT
ELECT
6800uF
1000uF
2200uF
470uF
47uF
20.00%
20.00%
20.00%
20.00%
20.00%
6.3V
16V
25V
16V
10V
C415
C416
C417
C418
1-126-767-11
1-126-935-11
1-126-964-11
1-126-948-11
ELECT
ELECT
ELECT
ELECT
1000uF
470uF
10uF
100uF
20.00%
20.00%
20.00%
20.00%
16V
16V
50V
35V
10%
10%
Ref. No.
Part No.
Description
Remarks
C419
1-126-959-11 ELECT
0.47uF
C420
C421
C422
C423
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
0.1uF
0.1uF
0.1uF
0.1uF
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
< CONNECTOR >
CN101
CN301
CN302
CN303
* CN305
1-784-733-11
1-784-780-11
1-779-564-11
1-568-828-11
1-564-706-11
CONNECTOR, FFC 11P
CONNECTOR, FFC 19P
CONNECTOR,FFC (LIF (NON-ZIF)) 27P
CONNECTOR, FFC 9P
PIN, CONNECTOR (SMALL TYPE) 4P
CN402
CN403
CN404
CN405
1-784-798-11
1-691-040-31
1-778-982-21
1-564-707-11
CONNECTOR, FFC 37P
CONNECTOR, FFC 8P
CONNECTOR, BOARD TO BOARD 13P
PIN, CONNECTOR (SMALL TYPE) 5P
< DIODE >
D102
D301
D302
D303
D304
8-719-988-61
8-719-988-61
6-500-522-21
6-500-522-21
6-500-522-21
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 10EDB40-TB3
DIODE 10EDB40-TB3
DIODE 10EDB40-TB3
D305
D306
D309
D401
D402
6-500-522-21
8-719-988-61
8-719-988-61
6-500-522-21
6-500-522-21
DIODE 10EDB40-TB3
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 10EDB40-TB3
DIODE 10EDB40-TB3
D403
D404
D405
D406
D407
6-500-522-21
6-500-522-21
6-500-522-21
6-500-522-21
6-500-522-21
DIODE 10EDB40-TB3
DIODE 10EDB40-TB3
DIODE 10EDB40-TB3
DIODE 10EDB40-TB3
DIODE 10EDB40-TB3
D408
D409
D410
D411
D412
6-500-522-21
8-719-988-61
6-500-522-21
8-719-988-61
6-500-522-21
DIODE 10EDB40-TB3
DIODE 1SS355TE-17
DIODE 10EDB40-TB3
DIODE 1SS355TE-17
DIODE 10EDB40-TB3
D413
D414
D415
D416
D417
8-719-988-61
8-719-988-61
8-719-083-70
8-719-069-55
8-719-988-61
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE UDZSTE-1727B
DIODE UDZSTE-175.6B
DIODE 1SS355TE-17
< EARTH TERMINAL >
70
20.00% 50V
* EP401
1-537-738-21 TERMINAL, EARTH
< IC >
IC201
IC301
IC302
IC401
IC402
6-702-130-01
6-703-650-11
8-759-828-32
8-759-231-57
6-701-760-01
IC HA12237F
IC M61529FP-D60G
IC PT8300
IC TA7810S
IC uPC3504AHF
IC403
IC404
8-759-231-57 IC TA7810S
8-759-039-69 IC uPC7805AHF
25V
25V
25V
25V
HCD-HP8V
MAIN
Ref. No.
Part No.
Description
Remarks
< JACK >
JK301
Part No.
Description
Remarks
Q408
Q409
8-729-140-04 TRANSISTOR
8-729-120-28 TRANSISTOR
2SB1116-TP-LK
2SC3052F-T1-LF
Q410
Q411
Q412
6-550-289-01 TRANSISTOR
8-729-120-28 TRANSISTOR
8-729-048-52 TRANSISTOR
2SA1235F
2SC3052F-T1-LF
2SA1932 (TP)
1-770-613-11 JACK, PIN 4P
< JUMPER RESISTOR >
JR101
JR102
JR201
JR202
JR203
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
JR204
JR301
JR302
JR303
JR304
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
JR305
JR307
JR308
JR313
JR401
1-216-864-11
1-216-296-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
JR402
JR403
JR404
JR405
JR406
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< COIL >
L201
Ref. No.
< RESISTOR >
R101
R102
R201
R202
R203
1-216-845-11
1-216-845-11
1-216-829-11
1-216-829-11
1-216-832-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
4.7K
4.7K
8.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R204
R207
R208
R209
R210
1-216-832-11
1-216-833-11
1-216-833-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
8.2K
10K
10K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R211
R212
R213
R216
R217
1-216-824-11
1-216-824-11
1-216-837-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.8K
1.8K
22K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R218
R219
R220
R221
R222
1-216-833-11
1-216-813-11
1-216-821-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
220
1K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R223
R224
R225
R226
R227
1-216-841-11
1-218-867-11
1-218-867-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
6.8K
6.8K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R228
R229
R230
R231
R232
1-216-829-11
1-216-815-11
1-216-797-11
1-216-838-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
330
10
27K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R233
R234
R235
R236
R237
1-216-837-11
1-216-837-11
1-216-829-11
1-216-833-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
22K
4.7K
10K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R238
R239
R240
R241
R242
1-216-829-11
1-216-833-11
1-216-833-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
10K
10K
470
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R243
R244
R245
R246
R247
1-216-833-11
1-216-833-11
1-216-829-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
4.7K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R301
R302
R303
R304
R305
1-216-829-11
1-216-829-11
1-216-829-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
4.7K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1-424-849-11 COIL, OSCILLATION (BIAS)
< TRANSISTOR >
Q201
Q202
Q203
Q204
Q205
8-729-120-28
8-729-120-28
8-729-120-28
8-729-120-28
6-550-289-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3052F-T1-LF
2SC3052F-T1-LF
2SC3052F-T1-LF
2SC3052F-T1-LF
2SA1235F
Q206
Q207
Q208
Q209
Q210
8-729-120-28
8-729-142-46
8-729-140-04
8-729-120-28
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3052F-T1-LF
2SC2001TP-LK
2SB1116-TP-LK
2SC3052F-T1-LF
2SC3052F-T1-LF
Q211
Q212
Q301
Q302
Q304
8-729-120-28
8-729-120-28
8-729-120-28
8-729-120-28
8-729-052-79
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3052F-T1-LF
2SC3052F-T1-LF
2SC3052F-T1-LF
2SC3052F-T1-LF
2SD1306NETL
Q305
Q306
Q307
Q309
Q310
8-729-052-79
6-550-289-01
8-729-120-28
6-550-289-01
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD1306NETL
2SA1235F
2SC3052F-T1-LF
2SA1235F
2SC3052F-T1-LF
Q311
Q312
Q313
Q314
Q401
8-729-120-28
8-729-052-79
8-729-052-79
8-729-900-63
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3052F-T1-LF
2SD1306NETL
2SD1306NETL
BN1F4M-TP
2SC3052F-T1-LF
Q402
Q406
Q407
8-729-209-60 TRANSISTOR
8-729-140-04 TRANSISTOR
8-729-120-28 TRANSISTOR
2SB1375
2SB1116-TP-LK
2SC3052F-T1-LF
71
HCD-HP8V
MAIN
Ref. No.
Part No.
Description
R306
R307
R308
R309
R310
1-216-829-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
10K
10K
10K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R311
R312
R313
R314
R315
1-216-825-11
1-216-833-11
1-216-833-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
10K
10K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R316
R317
R318
R319
R321
1-216-833-11
1-216-833-11
1-216-841-11
1-216-841-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
47K
47K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R322
R323
R324
R325
R326
1-216-821-11
1-216-833-11
1-216-821-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
1K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R327
R328
R329
R330
R331
1-216-821-11
1-216-809-11
1-216-809-11
1-216-833-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100
100
10K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R332
R333
R340
R341
R343
1-216-819-11
1-216-841-11
1-216-833-11
1-216-845-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
10K
100K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R344
R345
R346
R347
R348
1-216-837-11
1-216-837-11
1-216-837-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
22K
22K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R349
R350
R351
R352
R353
1-216-837-11
1-216-837-11
1-216-837-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
22K
22K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R354
R355
R356
R357
R358
1-216-829-11
1-216-829-11
1-216-837-11
1-216-845-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
22K
100K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R359
R360
R361
R362
R363
1-216-825-11
1-216-825-11
1-216-825-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R364
R365
R366
R367
R368
1-216-845-11
1-216-845-11
1-216-833-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
10K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R369
R370
R371
1-216-829-11 METAL CHIP
1-216-829-11 METAL CHIP
1-216-833-11 METAL CHIP
4.7K
4.7K
10K
5%
5%
5%
1/10W
1/10W
1/10W
72
Remarks
Ref. No.
Part No.
Description
Remarks
R375
R376
1-216-837-11 METAL CHIP
1-216-829-11 METAL CHIP
22K
4.7K
5%
5%
1/10W
1/10W
R377
R378
R379
R380
R381
1-216-837-11
1-216-829-11
1-218-717-11
1-218-717-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
4.7K
11K
11K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R382
R383
R384
R385
R389
1-218-717-11
1-218-717-11
1-216-837-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
11K
11K
22K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R390
R391
R392
R393
R394
1-216-837-11
1-218-717-11
1-218-717-11
1-216-837-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
11K
11K
22K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R395
R396
R397
R398
R399
1-216-845-11
1-216-829-11
1-216-829-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
4.7K
4.7K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R401
R402
R403
R404
R405
1-216-825-11
1-216-825-11
1-216-825-11
1-216-821-11
1-216-198-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
2.2K
2.2K
2.2K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/8W
R406
R407
R408
R409
R410
1-216-821-11
1-216-198-91
1-216-829-11
1-216-837-11
1-216-829-11
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
4.7K
22K
4.7K
5%
5%
5%
5%
5%
1/10W
1/8W
1/10W
1/10W
1/10W
R411
R412
R413
R414
R415
1-215-891-11
1-215-891-11
1-216-837-11
1-216-829-11
1-216-837-11
METAL OXIDE
METAL OXIDE
METAL CHIP
METAL CHIP
METAL CHIP
680
680
22K
4.7K
22K
5%
5%
5%
5%
5%
2W
2W
1/10W
1/10W
1/10W
R416
R417
R418
R419
R420
1-216-829-11
1-216-837-11
1-216-829-11
1-216-837-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
22K
4.7K
22K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R421
R427
R428
R429
R430
1-216-837-11
1-218-717-11
1-218-717-11
1-216-837-11
1-218-717-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
11K
11K
22K
11K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R431
R432
R433
R434
R435
1-218-717-11
1-216-837-11
1-216-841-11
1-216-829-11
1-216-806-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
11K
22K
47K
4.7K
56
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R436
R437
R438
R439
R440
1-216-806-11
1-216-829-11
1-216-829-11
1-216-829-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
56
4.7K
4.7K
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
HCD-HP8V
MAIN
Ref. No.
Remarks
PANEL
Part No.
Description
Part No.
Description
R441
R444
R445
R446
R447
1-216-821-11
1-216-829-11
1-216-829-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
4.7K
4.7K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C049
C050
C051
C052
C053
1-126-958-91
1-126-958-91
1-162-969-11
1-130-493-00
1-162-953-11
ELECT
ELECT
CERAMIC CHIP
MYLAR
CERAMIC CHIP
0.33uF
0.33uF
0.0068uF
0.068uF
100PF
20%
20%
10%
5%
5%
50V
50V
25V
50V
50V
R448
R449
R450
R451
R452
1-216-833-11
1-216-821-11
1-216-833-11
1-260-087-21
1-260-087-21
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
10K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/2W
1/2W
C054
C601
C602
C603
C604
1-126-960-11
1-126-964-11
1-126-964-11
1-126-947-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
1uF
10uF
10uF
47uF
10uF
20.00%
20.00%
20.00%
20.00%
20.00%
50V
50V
50V
10V
50V
R453
R454
R455
R456
R457
1-216-837-11
1-216-837-11
1-216-829-11
1-216-845-11
1-216-857-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
22K
4.7K
100K
1M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C605
C606
C607
C609
C610
1-164-156-11
1-128-551-11
1-119-774-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22uF
100uF
0.001uF
0.001uF
20.00%
20.00%
10%
10%
25V
25V
16V
50V
50V
R464
1-216-853-11 METAL CHIP
470K
5%
1/10W
C611
C612
C614
C616
C617
1-126-916-11
1-115-156-11
1-164-227-11
1-115-156-11
1-162-961-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1000uF
1uF
0.022uF
1uF
330PF
20.00% 6.3V
10V
10%
25V
10V
10%
50V
C618
C619
C620
C621
C622
1-164-156-11
1-128-551-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22uF
0.1uF
0.1uF
0.1uF
25V
20.00% 25V
25V
25V
25V
C635
C636
C637
C639
C640
1-162-918-11
1-162-919-11
1-124-257-00
1-119-772-91
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
18PF
22PF
2.2uF
47uF
0.01uF
5.00%
5%
20%
20.00%
10%
50V
50V
50V
35V
25V
C641
C642
C643
C646
C647
1-162-970-11
1-164-227-11
1-115-156-11
1-162-970-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.022uF
1uF
0.01uF
0.1uF
10%
10%
25V
25V
10V
25V
25V
C648
C649
C650
1-124-257-00 ELECT
1-124-234-00 ELECT
1-162-964-11 CERAMIC CHIP
2.2uF
22uF
0.001uF
20%
20%
10%
< SWITCH >
SW401
1-771-264-11 SWITCH, PUSH (DETECTION)(1 KEY)
(TAPE OPEN/CLOSE)
************************************************************
1-686-724-12 MODE MOTOR BOARD
******************
Ref. No.
MODE MOTOR
Remarks
************************************************************
A-4747-557-A PANEL BOARD, COMPLETE (E3,SP)
A-4747-565-A PANEL BOARD, COMPLETE (EA)
A-4747-569-A PANEL BOARD, COMPLETE (TH)
**********************
4-238-614-01 FL HOLDER (R)
< CAPACITOR >
C001
C002
C003
C004
C005
1-126-957-11
1-162-949-11
1-162-970-11
1-162-964-11
1-162-962-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
47PF
0.01uF
0.001uF
470PF
20.00%
5%
10%
10%
10%
50V
50V
25V
50V
50V
C006
C007
C008
C009
C010
1-126-956-91
1-126-964-11
1-126-964-11
1-164-156-11
1-126-961-11
ELECT
ELECT
ELECT
CERAMIC CHIP
ELECT
0.1uF
10uF
10uF
0.1uF
2.2uF
20.00% 50V
20.00% 50V
20.00% 50V
25V
20.00% 50V
C011
C012
C013
C014
C015
1-162-949-11
1-126-961-11
1-162-953-11
1-104-665-11
1-104-665-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
47PF
2.2uF
100PF
100uF
100uF
5%
20.00%
5%
20.00%
20.00%
50V
50V
50V
10V
10V
C020
C032
C041
C042
C043
1-164-156-11
1-126-961-11
1-165-176-11
1-162-969-11
1-162-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
2.2uF
0.047uF
0.0068uF
0.001uF
20.00%
10.00%
10%
10%
25V
50V
16V
25V
50V
C044
C045
C046
C047
C048
1-130-493-00
1-126-947-11
1-126-947-11
1-126-960-11
1-136-167-00
MYLAR
ELECT
ELECT
ELECT
FILM
0.068uF
47uF
47uF
1uF
0.15uF
5%
20.00%
20.00%
20.00%
5.00%
50V
16V
16V
50V
50V
10%
50V
16V
50V
< CONNECTOR >
CN601
CN602
1-784-759-11 CONNECTOR, FFC 37P
1-784-731-11 CONNECTOR, FFC 9P
< DIODE >
D003
D606
D607
D615
D616
8-719-069-54
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE UDZSTE-175.1B
DIODE 1SS355TE-17 (TH)
DIODE 1SS355TE-17 (EA)
DIODE 1SS355TE-17
DIODE 1SS355TE-17
D617
D619
D620
D621
D622
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
D623
D624
D625
D626
8-719-988-61
8-719-988-61
8-719-988-61
8-719-083-61
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE UDZSTE-1711B
73
HCD-HP8V
PANEL
Ref. No.
D627
Part No.
Description
Remarks
8-719-988-61 DIODE 1SS355TE-17
< FERRITE BEAD >
FB601
FB602
FB603
FB604
FB605
1-412-473-21
1-550-907-21
1-550-907-21
1-550-907-21
1-550-907-21
INDUCTOR
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
< FLUORESCENT INDICATOR >
FLD601 1-518-923-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC001
IC002
IC601
IC602
IC603
8-759-710-97
8-759-496-40
6-803-329-01
6-704-045-01
8-759-533-04
IC NJM4565M(TE2)
IC M65850FP
IC LC876796B-51Y2-E
IC MM1574A
IC M62703ML-E1
< JACK >
JK001
JK601
1-815-603-11 JACK (MIC)
1-691-293-21 JACK (PHONES)
< JUMPER RESISTOR >
JR605
JR606
JR607
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
0
0
0
5%
5%
5%
1/10W
1/10W
1/10W
< DIODE >
LED607
LED608
LED609
LED610
LED611
6-500-414-01
6-500-414-01
6-500-414-01
6-500-414-01
6-500-414-01
DIODE HL-30105Q2AT (DISC1)
DIODE HL-30105Q2AT (DISC2)
DIODE HL-30105Q2AT (DISC3)
DIODE HL-30105Q2AT (DISC4)
DIODE HL-30105Q2AT (DISC5)
Ref. No.
Part No.
Description
R030
R031
R032
R033
R034
1-216-809-11
1-216-829-11
1-216-848-11
1-216-834-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
4.7K
180K
12K
2.2K
5%
5%
5%
5%
5%
Remarks
1/10W
1/10W
1/10W
1/10W
1/10W
R035
R036
R037
R087
R088
1-216-841-11
1-216-825-11
1-216-817-11
1-216-820-11
1-216-820-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
2.2K
470
820
820
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R089
R090
R091
R092
R093
1-216-827-11
1-216-827-11
1-216-837-11
1-216-837-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
3.3K
22K
22K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R094
R095
R096
R097
R098
1-216-847-11
1-216-813-11
1-216-837-11
1-216-837-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
150K
220
22K
22K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R099
R604
R605
R606
R607
1-216-841-11
1-216-833-11
1-216-833-11
1-216-829-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
10K
10K
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R609
R610
R611
R612
R613
1-216-833-11
1-216-835-11
1-216-809-11
1-216-809-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
15K
100
100
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R614
R615
R616
R617
R619
1-216-821-11
1-216-821-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R620
R623
R624
R625
R626
1-216-833-11
1-216-198-91
1-216-835-11
1-216-817-11
1-216-819-11
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
15K
470
680
5%
5%
5%
5%
5%
1/10W
1/8W
1/10W
1/10W
1/10W
R627
R628
R629
R630
R631
1-216-821-11
1-216-823-11
1-216-823-11
1-216-825-11
1-216-827-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1.5K
1.5K
2.2K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R632
R633
R634
R635
R636
1-216-829-11
1-218-867-11
1-216-198-91
1-216-198-91
1-216-198-91
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
4.7K
6.8K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/8W
1/8W
R637
R638
R639
R640
R641
1-216-198-91
1-216-835-11
1-216-817-11
1-216-819-11
1-216-821-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
15K
470
680
1K
5%
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/10W
1/10W
R642
R643
R644
1-216-823-11 METAL CHIP
1-216-823-11 METAL CHIP
1-216-825-11 METAL CHIP
1.5K
1.5K
2.2K
5%
5%
5%
1/10W
1/10W
1/10W
LED614 6-500-415-01 DIODE HL-30105Q2IT (:/1)
< TRANSISTOR >
Q001
Q601
Q609
Q610
8-729-120-28
8-729-120-28
8-729-120-28
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3052F-T1-LF
2SC3052F-T1-LF
2SC3052F-T1-LF
2SC3052F-T1-LF
< RESISTOR >
R001
R002
R003
R004
R005
1-216-821-11
1-216-833-11
1-216-845-11
1-216-821-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
100K
1K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R006
R007
R008
R009
R010
1-216-809-11
1-216-833-11
1-216-849-11
1-216-809-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
220K
100
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R011
R012
R013
R022
R029
1-216-833-11
1-216-833-11
1-216-821-11
1-216-833-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
1K
10K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
74
HCD-HP8V
PANEL
Ref. No.
Part No.
Description
Remarks
R645
R646
1-216-827-11 METAL CHIP
1-216-849-11 METAL CHIP
3.3K
220K
5%
5%
1/10W
1/10W
R647
R648
R649
R650
R651
1-220-397-11
1-216-819-11
1-216-198-91
1-216-198-91
1-216-833-11
RES-CHP
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
4.7M
680
1K
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/8W
1/10W
R652
R653
R654
R655
R656
1-216-809-11
1-216-801-11
1-216-833-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
22
10K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R657
R658
R659
R660
R661
1-216-829-11
1-216-833-11
1-216-833-11
1-216-198-91
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
4.7K
10K
10K
1K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/8W
1/10W
R662
R663
R664
R665
R666
1-216-819-11
1-216-821-11
1-216-823-11
1-216-809-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
1K
1.5K
100
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R667
R668
R669
R670
R671
1-216-813-11
1-216-809-11
1-216-823-11
1-216-198-91
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
220
100
1.5K
1K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/8W
1/10W
R672
R673
R674
R675
R676
1-216-827-11
1-216-829-11
1-216-829-11
1-218-867-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
4.7K
4.7K
6.8K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R677
R678
R679
R680
R681
1-216-851-11
1-216-833-11
1-216-198-91
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
330K
10K
1K
100
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/10W
1/10W
R682
R683
R684
R685
R686
1-216-845-11
1-216-833-11
1-216-182-00
1-216-182-00
1-218-867-11
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
100K
10K
220
220
6.8K
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/8W
1/10W
R687
R688
R689
R690
R691
1-216-833-11
1-216-809-11
1-216-833-11
1-216-809-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
10K
100
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R692
R693
R694
R695
R696
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R697
R698
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
100
100
5%
5%
1/10W
1/10W
Ref. No.
Part No.
PWR AMP
Description
Remarks
< IC >
RM601
6-600-174-01 IC RPM7240-H4 (g)
< SWITCH >
S601
S602
S603
S604
S605
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, TACT (DISC1)
SWITCH, TACT (DISC2)
SWITCH, TACT (DISC3)
SWITCH, TACT (DISC4)
SWITCH, TACT (DISC5)
S606
S607
S608
S609
S610
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, TACT (DISC5 Z)
SWITCH, TACT (DISC4 Z)
SWITCH, TACT (DISC3 Z)
SWITCH, TACT (DISC2 Z)
SWITCH, TACT (DISC1 Z)
S614
S615
S616
S617
S618
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, TACT (TAPE bB)
SWITCH, TACT (TUNER/BAND)
SWITCH, TACT (CD)
SWITCH, TACT (B)
SWITCH, TACT (x)
S619
S620
S621
S622
S627
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, TACT (TUNING+)
SWITCH, TACT (TUNING-)
SWITCH, TACT (PRSET/ALBUM-)
SWITCH, TACT (PRSET/ALBUM+)
SWITCH, TACT (@/1)
S628
S629
S630
S631
S632
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, TACT (DISPLAY)
SWITCH, TACT (PLAY MODE)
SWITCH, TACT (REPEAT)
SWITCH, TACT (CD SYNC)
SWITCH, TACT (REC (PAUSE/START))
S633
S634
S635
S636
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, TACT (GROOVE)
SWITCH, TACT (PRESET EQ)
SWITCH, TACT (DIMMER)
SWITCH, TACT (FUNCTION)
< VARIABLE RESISTOR >
VR001
VR002
VR601
1-225-739-11 RES, VAR CARBON 50K (MIC LEVEL)
1-225-739-11 RES, VAR CARBON 50K (ECHO LEVEL)
1-477-194-11 ENCODER, ROTARY (12 TYPE)(VOLUME)
< VIBRATOR >
X601
1-760-252-12 VIBRATOR, CRYSTAL (32.768kHz)
************************************************************
A-4734-342-A PWR AMP BOARD, COMPLETE (EXCEPT TH)
A-4747-550-A PWR AMP BOARD, COMPLETE (TH)
*************************
< CAPACITOR >
< VIBRATOR >
RES601 1-579-125-11 VIBRATOR, CERAMIC (8.0MHz)
C501
C502
C503
C504
C505
1-126-964-11
1-126-964-11
1-162-964-11
1-162-964-11
1-162-960-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
0.001uF
0.001uF
220PF
20.00%
20.00%
10%
10%
10%
50V
50V
50V
50V
50V
C506
C507
C508
C509
C510
1-162-960-11
1-126-964-11
1-126-964-11
1-126-966-11
1-164-156-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
220PF
10uF
10uF
33uF
0.1uF
10%
20.00%
20.00%
20.00%
50V
50V
50V
16V
25V
75
HCD-HP8V
PWR AMP
Ref. No.
Part No.
Description
C511
C513
C514
C515
C516
1-126-963-11
1-104-665-11
1-126-963-11
1-165-128-11
1-165-128-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
4.7uF
100uF
4.7uF
0.22uF
0.22uF
20.00% 50V
20.00% 10V
20.00% 50V
16V
16V
Remarks
C517
C518
C520
C523
C524
1-162-960-11
1-126-961-11
1-126-968-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
220PF
2.2uF
100uF
0.1uF
0.1uF
10%
50V
20.00% 50V
20.00% 50V
25V
25V
C525
C526
C527
C528
C529
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C530
C531
C532
C541
C542
1-164-156-11
1-164-156-11
1-164-156-11
1-136-165-00
1-128-550-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
FILM
ELECT
0.1uF
0.1uF
0.1uF
0.1uF
2200uF
25V
25V
25V
5.00% 50V
20.00% 50V
C543
C544
1-136-165-00 FILM
1-128-550-11 ELECT
0.1uF
2200uF
5.00% 50V
20.00% 50V
25V
25V
25V
25V
25V
Ref. No.
JR505
Part No.
Remarks
0
5%
1/10W
< COIL >
L501
L502
1-422-009-13 COIL, AIR-CORE
1-422-009-13 COIL, AIR-CORE
< TRANSISTOR >
Q501
Q502
Q503
Q504
Q505
8-729-120-28
6-550-646-01
6-550-646-01
8-729-120-28
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3052F-T1-LF
2SC3143K4/K5-TB
2SC3143K4/K5-TB
2SC3052F-T1-LF
2SC3052F-T1-LF
Q506
Q507
Q508
Q509
Q510
8-729-900-36
8-729-120-28
8-729-120-28
6-550-289-01
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
BA1F4M-TP
2SC3052F-T1-LF
2SC3052F-T1-LF
2SA1235F
2SC3052F-T1-LF
Q511
Q512
Q513
Q514
Q515
8-729-120-28
8-729-120-28
8-729-120-28
8-729-120-28
8-729-140-04
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3052F-T1-LF
2SC3052F-T1-LF
2SC3052F-T1-LF
2SC3052F-T1-LF
2SB1116-TP-LK
< RESISTOR >
< CONNECTOR >
CN501
CN503
* CN504
Description
1-216-864-11 METAL CHIP
< DIODE >
R501
R502
R503
R504
R507
1-216-821-11
1-216-821-11
1-216-842-11
1-216-842-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
56K
56K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1-778-982-21 CONNECTOR, BOARD TO BOARD 13P
1-564-506-11 PLUG, CONNECTOR 3P
1-564-704-11 PIN, CONNECTOR (SMALL TYPE) 2P
D501
D502
D503
D504
D505
8-719-510-68
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE D5SBA204101
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
R508
R509
R510
R511
R512
1-216-821-11
1-216-833-11
1-216-839-11
1-216-821-11
1-216-842-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
33K
1K
56K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
D506
D507
D508
D509
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
R513
R514
R515
R516
R517
1-216-842-11
1-216-821-11
1-216-821-11
1-216-835-11
1-216-835-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
56K
1K
1K
15K
15K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R518
R519
R520
R521
R522
1-216-841-11
1-216-841-11
1-260-076-21
1-260-076-21
1-217-151-00
METAL CHIP
METAL CHIP
CARBON
CARBON
METAL
47K
47K
10
10
0.22
5%
5%
5%
5%
10%
1/10W
1/10W
1/2W
1/2W
2W
R523
R524
R525
R526
R527
1-217-151-00
1-216-162-00
1-216-854-11
1-216-813-11
1-216-841-11
METAL
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0.22
33
560K
220
47K
10%
5%
5%
5%
5%
2W
1/8W
1/10W
1/10W
1/10W
R528
R529
R530
R531
R532
1-216-845-11
1-216-842-11
1-216-845-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
56K
100K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R533
R534
1-216-829-11 METAL CHIP
1-216-841-11 METAL CHIP
4.7K
47K
5%
5%
1/10W
1/10W
< EARTH TERMINAL >
* EP501
1-537-738-21 TERMINAL, EARTH
< FUSIBLE >
0 FR501
0 FR502
1-202-972-61 FUSIBLE
1-212-881-11 FUSIBLE
1
100
5%
5%
1/4W
1/4W
< IC >
IC501
6-600-089-01 IC STK403-070
< TERMINAL BOARD >
JK501
1-694-884-11 TERMINAL BOARD (4P)(SPEAKER)
< JUMPER RESISTOR >
JR501
JR502
JR503
JR504
76
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
PWR AMP
PWR TRANS
ST ENCODER
Ref. No.
Part No.
ROLLER MOTOR
STOCKER MOTOR
Description
SUB TRANS
Remarks
R535
R536
R537
1-216-830-11 RES-CHIP
1-216-825-11 METAL CHIP
1-216-829-11 METAL CHIP
5.6K
2.2K
4.7K
5%
5%
5%
1/10W
1/10W
1/10W
R538
R539
R540
R543
R544
1-216-829-11
1-216-829-11
1-216-833-11
1-216-837-11
1-216-842-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
10K
22K
56K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R545
R546
R547
R548
R549
1-216-841-11
1-216-839-11
1-216-833-11
1-216-174-00
1-216-174-00
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
47K
33K
10K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/8W
1/8W
R550
R551
1-260-076-21 CARBON
1-260-076-21 CARBON
10
10
5%
5%
1/2W
1/2W
Ref. No.
SENSOR (FAN)
SW (1)
Part No.
HCD-HP8V
SENSOR
SW (2)
Description
SW (3)
Remarks
ST ENCODER BOARD
*****************
************************************************************
1-686-725-12 STOCKER MOTOR BOARD
*********************
************************************************************
1-689-246-12 SUB TRANS BOARD
****************
< CAPACITOR >
C901
RY501 1-755-373-11 RELAY
************************************************************
CN908
< DIODE >
< CAPACITOR >
1-164-159-21 CERAMIC
1-126-969-11 ELECT
0.1uF
220uF
50V
20.00% 50V
D901
D902
D903
D904
D905
1-564-519-11 PLUG, CONNECTOR 4P
1-564-719-11 PIN, CONNECTOR (SMALL TYPE) 3P
1-564-524-11 PLUG, CONNECTOR 9P
< DIODE >
D907
6-500-522-21
6-500-522-21
6-500-522-21
6-500-522-21
8-719-988-61
DIODE 10EDB40-TB3
DIODE 10EDB40-TB3
DIODE 10EDB40-TB3
DIODE 10EDB40-TB3
DIODE 1SS355TE-17
< RELAY >
< CONNECTOR >
* CN902
* CN904
* CN907
20.00% 16V
1-564-321-21 PIN, CONNECTOR (3.96mm PITCH) 2P (TH)
1-568-106-11 PIN, CONNECTOR (3.96mm PITCH) 4P
(EXCEPT TH)
1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P
1-689-250-11 PWR TRANS BOARD
*****************
C902
C903
1000uF
< CONNECTOR >
CN905
CN905
< RELAY >
1-126-767-11 ELECT
0 RY901
1-755-276-11 RELAY, POWER
< SWITCH >
0 S902
1-786-055-21 SELECTOR, VOLTAGE (VOLTAGE SELECTOR)
(EXCEPT TH)
6-500-522-21 DIODE 10EDB40-TB3
< TRANSFORMER >
< FUSIBLE >
0 FR903 1-217-639-00 FUSIBLE
2.2
5%
1/4W
************************************************************
0 T902
1-439-832-11 TRANSFORMER, POWER
************************************************************
1-686-727-12 SW (1) BOARD
************
1-686-726-12 ROLLER MOTOR BOARD
********************
< SWITCH >
************************************************************
S711
1-689-248-12 SENSOR (FAN) BOARD
*******************
< THERMISTOR >
TH501 1-807-796-11 THERMISTOR
************************************************************
1-686-723-12 SENSOR BOARD
**************
< IC >
IC751
8-749-017-45 SENSOR, PHONT RPR-220C1N
(DISC INSERT DETECT SENSOR)
************************************************************
1-786-382-11 SWITCH, PUSH (1 KEY)
(DISC INSERT (8/12cm))
************************************************************
1-686-728-12 SW (2) BOARD
************
S713
1-786-382-11 SWITCH, PUSH (1 KEY)(DISC IN (8/12cm))
S714
1-786-382-11 SWITCH, PUSH (1 KEY)(DISC IN (8cm))
************************************************************
1-686-729-12 SW (3) BOARD
************
S715
1-786-382-11 SWITCH, PUSH (1 KEY)(DISC OUT)
************************************************************
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
77
HCD-HP8V
SW (4)
Ref. No.
VMP
Part No.
Description
Remarks
1-686-730-12 SW (4) BOARD
************
S716
1-786-382-11 SWITCH, PUSH (1 KEY)(STOCKER IN/OUT)
S717
1-786-382-11 SWITCH, PUSH (1 KEY)(DISC POSITION)
S718
1-786-382-11 SWITCH, PUSH (1 KEY)(STOCKING)
************************************************************
A-4747-564-A VMP BOARD, COMPLETE (EXCEPT TH)
A-4747-576-A VMP BOARD, COMPLETE (TH)
********************
< CAPACITOR >
C104
C105
C106
C114
C115
1-124-778-00
1-162-968-11
1-164-670-11
1-124-778-00
1-164-156-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
22uF
0.0047uF
1200PF
22uF
0.1uF
20%
10%
5.00%
20%
6.3V
50V
16V
6.3V
25V
C116
C154
C155
C156
C201
1-126-206-11
1-124-778-00
1-162-968-11
1-164-670-11
1-124-778-00
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
100uF
22uF
0.0047uF
1200PF
22uF
20%
20%
10%
5.00%
20%
6.3V
6.3V
50V
16V
6.3V
C202
C203
C204
C205
C206
1-164-156-11
1-126-206-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
0.1uF
0.1uF
0.1uF
C207
C208
C209
C210
C211
1-164-156-11
1-164-156-11
1-124-778-00
1-164-156-11
1-126-206-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
0.1uF
22uF
0.1uF
100uF
C212
C213
C214
C221
C222
1-164-156-11
1-124-778-00
1-124-778-00
1-124-779-00
1-124-779-00
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
0.1uF
22uF
22uF
10uF
10uF
C223
C224
C253
C254
C255
1-126-206-11
1-164-156-11
1-216-864-11
1-164-156-11
1-164-156-11
ELECT CHIP
CERAMIC CHIP
METAL CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0
0.1uF
0.1uF
20%
C257
C258
C259
C321
C322
1-128-065-11
1-164-156-11
1-126-206-11
1-162-919-11
1-162-917-11
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
68uF
0.1uF
100uF
22PF
15PF
20.00% 10V
25V
20%
6.3V
5%
50V
5%
50V
C323
C338
C360
C361
C364
1-162-915-11
1-164-156-11
1-126-206-11
1-164-156-11
1-124-779-00
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
10PF
0.1uF
100uF
0.1uF
10uF
0.5PF
C365
C366
C501
C502
C503
1-126-206-11
1-126-206-11
1-124-779-00
1-164-156-11
1-164-156-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
100uF
10uF
0.1uF
0.1uF
C504
1-164-156-11 CERAMIC CHIP
0.1uF
20%
25V
6.3V
25V
25V
25V
20%
25V
25V
6.3V
25V
6.3V
20%
20%
20%
20%
25V
6.3V
6.3V
16V
16V
20%
5%
6.3V
25V
1/10W
25V
25V
Ref. No.
Part No.
Description
C505
C510
C511
C513
1-164-156-11
1-164-156-11
1-164-156-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.001uF
Remarks
C521
C522
C523
C524
C525
1-164-156-11
1-162-912-11
1-162-912-11
1-164-156-11
1-126-193-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
7PF
7PF
0.1uF
1uF
20%
25V
50V
50V
25V
50V
C533
C534
C535
C536
C537
1-164-156-11
1-164-315-11
1-110-563-11
1-164-217-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
470PF
0.068uF
150PF
100PF
5.00%
10.00%
5.00%
5%
25V
50V
16V
50V
50V
C538
C539
C540
C541
C542
1-126-206-11
1-117-863-11
1-164-156-11
1-162-974-11
1-164-156-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.47uF
0.1uF
0.01uF
0.1uF
20%
6.3V
10.00% 6.3V
25V
50V
25V
C543
C544
C545
C546
C547
1-164-315-11
1-117-863-11
1-126-193-11
1-164-156-11
1-126-193-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
470PF
0.47uF
1uF
0.1uF
1uF
5.00% 50V
10.00% 6.3V
20%
50V
25V
20%
50V
C548
C549
C550
C551
C552
1-164-156-11
1-162-913-11
1-162-913-11
1-164-156-11
1-126-193-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
8PF
8PF
0.1uF
1uF
25V
0.50PF 50V
0.50PF 50V
25V
20%
50V
C561
C566
C567
C570
C571
1-164-156-11
1-126-206-11
1-164-156-11
1-162-967-11
1-164-156-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
20%
0.1uF
0.0033uF 10%
0.1uF
25V
6.3V
25V
50V
25V
C572
C573
C574
C575
C576
1-164-156-11
1-164-156-11
1-164-156-11
1-126-206-11
1-126-206-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
0.1uF
0.1uF
0.1uF
100uF
100uF
25V
25V
25V
6.3V
6.3V
C581
C582
C583
C584
C596
1-164-156-11
1-124-779-00
1-164-156-11
1-164-156-11
1-124-779-00
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
10uF
0.1uF
0.1uF
10uF
C597
1-124-779-00 ELECT CHIP
10uF
10%
0.5PF
0.5PF
20%
20%
20%
25V
16V
25V
25V
16V
20%
16V
20%
< CONNECTOR >
20%
20%
50V
25V
6.3V
25V
16V
CN101
CN201
CN301
1-784-327-21 CONNECTOR, FFC/FPC 28P
1-778-874-11 CONNECTOR,FFC(LIF (NON-ZIF)) 19P
1-794-509-11 PIN, CONNECTOR (PC BOARD)(3P)
< FERRITE BEAD >
78
20%
20%
20%
6.3V
6.3V
16V
25V
25V
25V
FB201
FB251
FB252
FB360
FB501
1-469-869-21
1-469-869-21
1-469-869-21
1-469-869-21
1-469-869-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
25V
25V
25V
50V
HCD-HP8V
VMP
Ref. No.
FB502
FB503
FB504
FB561
Part No.
Description
1-469-869-21
1-469-869-21
1-469-869-21
1-469-869-21
FERRITE
FERRITE
FERRITE
FERRITE
Remarks
0uH
0uH
0uH
0uH
< FILTER >
FL201
FL501
FL502
FL503
FL504
1-234-177-21
1-234-177-21
1-234-177-21
1-234-177-21
1-234-177-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
< IC >
IC102
IC201
IC202
IC307
IC504
8-759-701-40
6-700-399-01
8-759-460-72
6-702-001-01
8-759-825-13
IC NJM2100M (TE2)
IC uPC2925T-E1
IC BA033FP-E2
IC BD7600FV-E2
IC PCM1748E/2K
IC505
IC506
IC507
IC508
8-752-417-93
6-702-000-01
6-702-571-01
6-802-823-01
IC CXD1887R
IC BU2507FV-E2
IC VG3612816BT-7L
IC MR27V401E-0B1MAZ060
< JUMPER RESISTOR >
JW203
1-216-864-11 METAL CHIP
0
5%
1-410-373-31 INDUCTOR
2.2uH
1-410-381-11 INDUCTOR CHIP 10uH
< TRANSISTOR >
Q201
Q301
Q370
Q581
8-729-140-75
8-729-602-36
8-729-028-96
8-729-602-21
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Part No.
Description
R506
R507
R508
R509
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
5%
5%
5%
5%
Remarks
1/10W
1/10W
1/10W
1/10W
R510
R511
R512
R513
R516
1-216-809-11
1-216-809-11
1-216-809-11
1-216-833-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
10K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R517
R522
R531
R532
R533
1-216-826-11
1-216-833-11
1-216-845-11
1-216-829-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.7K
10K
100K
4.7K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R534
R537
R538
R541
R542
1-216-864-11
1-216-864-11
1-216-833-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
10K
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R543
R544
R545
R546
R547
1-216-853-11
1-216-857-11
1-216-821-11
1-216-848-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
1M
1K
180K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R548
R549
R550
R551
R552
1-216-855-11
1-216-845-11
1-216-833-11
1-218-852-11
1-216-820-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680K
100K
10K
1.6K
820
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R554
R555
R556
R557
R558
1-216-797-11
1-216-797-11
1-216-797-11
1-216-797-11
1-216-857-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
10
10
10
1M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R559
R561
R581
R582
1-216-817-11
1-216-821-11
1-216-809-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
1K
100
470
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< COIL >
L102
L321
Ref. No.
2SD999-T1-CLCK
2SA1602TP-1EF
RT1N141M-TP-1
2SC4154TP-1EF
< RESISTOR >
R102
R107
R108
R109
R114
1-216-809-11
1-216-833-11
1-216-823-11
1-216-823-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
1.5K
1.5K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R115
R152
R157
R158
R159
1-216-825-11
1-216-809-11
1-216-833-11
1-216-823-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
100
10K
1.5K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R201
R202
R321
R322
R323
1-216-809-11
1-216-809-11
1-216-813-11
1-216-864-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
220
0
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R375
R376
R502
R503
R504
1-211-990-11
1-216-833-11
1-216-827-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
75
10K
3.3K
100
100
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R505
1-216-809-11 METAL CHIP
100
5%
1/10W
< VIBRATOR >
X501
1-767-518-11 VIBRATOR, CRYSTAL (33.8688MHz)
X502
1-767-519-11 VIBRATOR, CRYSTAL (27MHz)
************************************************************
MISCELLANEOUS
*************
11
12
63
65
105
1-827-392-11
1-796-351-41
1-769-920-11
1-827-395-11
1-787-025-11
WIRE (FLAT TYPE)(8 CORE)
MECHANISM, SIGNAL CASSETTE
WIRE (FLAT TYPE)(9 CORE)
WIRE (FLAT TYPE)(37 CORE)
DC FAN
107
108
0 151
0 151
0 151
1-693-628-11
1-769-946-11
1-824-818-11
1-783-532-11
1-791-901-12
TUNER (FM/AM)
WIRE (FLAT TYPE)(11 CORE)
CORD, POWER (WITH CONNECTOR)(TH)
CORD, POWER (EA,SP)
CORD, POWER (E3)
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
79
HCD-HP8V
Ref. No.
Part No.
Description
155
156
161
606
0 607
1-827-390-11
1-827-391-11
1-827-394-11
1-782-817-11
A-4735-189-A
WIRE (FLAT TYPE)(27 CORE)
WIRE (FLAT TYPE)(28 CORE)
WIRE (FLAT TYPE)(19 CORE)
WIRE (FLAT TYPE)(16 CORE)
BU-30 (61) ASSY (including M101, M102)
0 F901
0 F902
0 F903
0 F904
0 F905
1-533-473-11
1-533-473-11
1-533-470-11
1-533-470-11
1-533-471-11
FUSE, GLASS TUBE (DIA. 5)
FUSE, GLASS TUBE (DIA. 5)
FUSE, GLASS TUBE (DIA. 5)
FUSE, GLASS TUBE (DIA. 5)
FUSE, GLASS TUBE (DIA. 5)(EXCEPT TH)
A-4735-953-A
A-4735-953-A
A-4735-953-A
1-477-299-11
1-477-300-11
MOTOR ASSY (STOCKER)
MOTOR ASSY (MODE)
MOTOR ASSY (ROLLER)
ENCODER, ROTARY (STOCKER POSITION)
ENCODER, ROTARY (MODE)
M761
M771
M781
S702
S771
0 T901
0 T901
Remarks
1-439-834-11 TRANSFORMER, POWER (EXCEPT EA)
1-439-835-11 TRANSFORMER, POWER (EA)
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
80
Ref. No.
Part No.
Description
Remarks
HCD-HP8V
MEMO
81
HCD-HP8V
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
Date
1.0
2003.07
Description of Revision
New