Download SERVICE MANUAL
Transcript
FACSIMILE WC-M15i Series SERVICE MANUAL Contents FACSIMILE 1. Precautions 2. Specifications 3. Circuit Description 4. Disassembly 5. Troubleshooting 6. Exploded Views and Parts List 7. Electrical Parts List 8. Block Diagram 9. Connection Diagram 10. Schematic Diagrams - This Service Manual is a property of Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable International and/or domestic law. - 1. Precautions 1-1 Safety Precautions Read each caution carefully: 1. Do not use this printer near water or when exposed to inclement weather. 2. Do not place this printer on an unstable cart, stand or table; the product may fall, causing serious damage to the product. 3. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation and to protect the printer from everheating, do not block or cover any of these openings. Do not place the printer in an enclosure unless the enclosure provides adequate ventilation. 4. Never push objects of any kind into the printer through the cabinet ventilation slots as they may touch dangerous high voltage points, create short circuits, cause a fire, or produce an electrical shock. Never spill liquid of any kind on the printer. 5. Do not place the printer in a location where someone may trip on the cords. 6. Select a work surface that is large enough to hold the printer. 7. Position the printer within six feet of the computer and within five feet of an electrical outlet. 8. Operate this printer using the power source (110V, 220V, etc) indicated on the marking label. If you are not sure of the type of power source available, consult your dealer or local power company. 9. If you need to use an extension power cord with this printer, make sure that it uses a three-wire grounded cord and that the total ampere ratings for all of the products using the extension do not exceed the extension cord ampere rating. Also, make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes. 10. Do not allow anything to rest on the power cord or data communications cable. 11. Unplug this printer from the wall outlet before cleaning. Do not use liquid cleaners or aerosol sprays. Use a damp cloth for cleaning. 12. Do not touch the surface of the photo-sensitive drum as marks or scratches may impair print quality. Samsung Electronics 13. Do not expose the drum unit to direct light for prolonged periods. 14. Use only standard papers, OHP films, and approved envelopes. Feed OHP films though the manual feed slot only. See specifications for approved papers and envelopes. 15. Other than replacing consumables such as paper and toner, refer all questions to qualified service personnel. LASER STATEMENT (LASERTURVALLISUUS) WARNING : NEVER OPERATE AND SERVICE THE PRINTER WITH THE PROTECTIVE COVER REMOVED FROM LASER/SCANNER ASSEMBLY. THE REFLECTIVE BEAM, ALTHOUGH INVISIBLE, CAN DAMAGE YOUR EYES. Class 1 laser product Luokan 1 laserlaite Klass 1 laser apparat Allonpituus 770-795nm Teho 0.3mW±0.03mW CAUTION INVISIBLE LASER RADIATION WHEN THIS COVER OPEN. DO NOT OPEN THIS COVER. VORSICHT UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEOFFNET. NIGHT DEM STRAHL AUSSETZEN. ATTENTION REYONNEMENT LASER INVISIBLE EN CAS D’OUVERTURE. EXPOSITION DANGERUSE AU FAISCEAU. ATTENZIONE RADIAZIONE LASER INVISIBLE IN CASO DI APERTURA. EVITARE L’ESPOSIZONE LA FASCIO. PRECAUCION REDIACION LASER INVISIBLE CUANDO SE ABRE. EVITAR EXPONERSE AL RAYO. CAUTION : Avoid exposure to invisible laser radiation when the development unit is not installed. 1-1 Precautions 1-2 Servicing Precautions Note : Requirements for AC power are described on the label affixed to the rear of the printer. Check the AC voltage rating requirement before use. 1. Before disassembly, pull the power plug from the AC power connector. 2. To avoid spilling toner inside the machine, do not turn the printer over or on its side before removing the developer cartridge. 3. Faulty installation of DRAMs may cause permanent damage to the Laser Printer. 4. Use only+5V power for video controller-related circuitry. 5. When replacing parts, use only the same type of part as the original. Replacing components with a second vendor’s part may cause faulty operation. 6. Check the insulation between the blades of the AC plug and accessible conductive parts (examples : metal panels and input ports). 7. Insulation Checking Procedure: Disconnect the power cord from the AC power source. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see left) should be greater than 1 megaohm. 8. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 9. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last. 1-3 ESD Precautions Some semiconductor (“solid state”) devices are easily damaged from static electricity. Such components commonly are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits (ICs), LargeScale Integrated circuits (LSIs), some field-effect transistors, and semiconductor chip components. The following techniques will reduce the occurrence of component damage caused by static electricity: CAUTION : Be sure the power is off to the chassis or circuit board, and observe all other safety precautions charge to damage ESDs. 1. Immediately before handling any semiconductor components assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist strap device. (Be sure to remove the strap before applying power to the unit under test to avoid potential shock.) 2. After removing ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge. 3. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs. 4. Use only a ground-tip soldering iron when soldering or desoldering ESDs. 5. Use only anti-static solder removal device. Some solder removal devices are not rated as “antistatic;”these can accumulate sufficient electrical 1-2 Samsung Electronics 2. Specifications Note: It is subject to change without notice. Item Specification & Description Engine Print Speed Resolution Source of Light Print Method Feed Method Paper Handling (input) MLE-6000 12PPM (A4 Size, 5% Character Pattern) True 600 x 600 dpi, 1200 dpi class RET Laser Diode (LSU:Laser Scanner Unit) Non-impact Electrophotography Cassette & Manual, Option Feeder *Size (1) Standard : A4, Letter, Legal, B5, Executive, Folio (2) Envelope : MP Tray only Paper Type Paper size(mm2) Monarch 98.5 x 190.5 Com-10 104.9 x 241.3 Intl-DL 110 x 220 Intl C5 162 x 229 (3) Universal type Length : 150 ~ 356 mm Width : 90 ~ 216 mm *Weigh : For Cassette, 60 ~ 90 g/m2 For MPF, 60 ~ 143 g/m2 *Recommended Paper USA : X400, X4024, , BOISECASCADE EC : REFLEX, ADAGIO Transparancies : 3M(CG3300 or 3360) Label : AVERY 53XX series Face Down : 250 sheets, Face Up : 10 sheets Cassette : 250 sheets of paper (75g/m2) MPF : 100 sheets of paper (A4) 30 sheets of transparencies 10 envelopes or card stocks 25 paper labels Option Cassette : 250 sheets of paper 50 seconds or less (23°C, 50%) 14 seconds or less (Fast Mode) AC100~120V/ 220~240V(±15%), 50/60Hz (±3%) During Printing : 300WH (average) During Sleep : Less than 30W Less than 30W during 1 hour when it turned on C-UL, TUV, FCC, CDRH, CE, CB Stand by : Less than 36dB, Operating : Less than 49dB Print Cartridge Paper Handing (output) Feed Capacity Warm-up time First Print Time Power Rating Power Consumption Power Saving Consumption Certification & Compliance Acoustic Noise Toner Supply Samsung Electronics 2-1 Specifications Item Specification & Description Expected Life Span 150,000 sheets Operating Environment Temperature : 10~30°C, Humidity : 20~80%RH Storage Environment Temperature : 0~35°C, Humidity : 10~90%RH Weigh Net : Max 11Kg, Gross : 12Kg External Dimension 420 (W) x 368 (D) x 220 (H)mm Print Cartridge Life Span : 6,000 pages, 5% Pattern Developing : Non-magnetic Contact Developing Charging : Conductive Roller Charging Density Adjustment : 3 step (Light, Medium, Dark) Toner Supply Method : Exchanging the Developer Toner Checking Sensor : None Transfer System : Conductive Roller Transfer Fusing System : Temperature & Pressure Ozone Emission : Less than 0.1 PPM Emulation PCL5e,PCL6, optional PostScript Level 2 Compatible Font 1 bitmap 45 scalable (35 intelligent, 10 truetype) CPU Power PC 603e (clock speed 80MHz) RAM Memory Standard 4M byte (16M bit x 2) Option SIMM Module ; 4, 8, 16, 32,64M byte *Refer to Operator’s Guide for instructions on SIMM installation. ROM 4M byte (8M bit x 2 : Program) Flash Memory EEPROM 512 bytes Interface Bidirectional Parallel Standard - IEEE 1284 COMPATIBLE MODE - IEEE 1284 NIBBLE MODE - IEEE 1284 BYTE MODE - IEEE 1284 ECP WITHOUT RLE - IEEE 1284 ECP WITH RLE USB Interface Standard - USB 1.0 compliant - 12Mbps 1 port Serial/Localtalk Interface Optional Serial (RS-232C) - 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 1152bps - XON/XOFF, DTR/DST Protocol - Rubust XON for XON/XOFF LOCALTALK - Macintosh Host Interface 230.4KBPS, SDLC, FMO Coding, RS-232C Network Interface 100--Base -Tx or 10 Base T Autoselect Interface Switching Automatic (Serial & Parallel) Interface Time Out 5 min (max.) 2-2 Samsung Electronics 3. Reference Information 3-1 Abbreviations and Acronyms Tables 3-1-1 and 3-1-2 list abbreviations and acronyms which may be found in this service manual. Abbreviations Abbr Definition Abbr Definition amps amperes motor_pa Motor phase A ass’y assembly motor_pb Motor phase B badac bad access mpx multiplex bps bits per second neg negative CBUSY Command busy od open drain CCLK Command clock OSC oscillator clk clock OUT output cm centimeter(s) pba printed board assembly CMSG Command message pcb printed circuit board CON connector pix picture DS Data Strobe Pmotor LSU motor on EBUSY Engine Status busy pos positive or position EMSG Engine Status message pot potential Exitpap Exit paper ppm print pages per minute GND ground PRINT Print command HLDA hold acknowledge psync page synchronization hldar hold acknowledge received pwr power HLDR hold request Q_Lamp Quenching Lamp HOR horizontal qty quantity HSYNC Horizontal sync READY Engine print ready I/O Input and Output sw switch in inch(es) or input tach tachometer INT Interrupt thvea Transfer high voltage Enable INTA Interrupt Acknowledge Vcc collector supply voltage (dc) INTR Interrupt Request VDI Video data from controller lb. Pound(s) VDO Video data output LDON laser Diode On vert vertical lin linearit Vp-p peak-to-peak voltage lock bus lock VR variable resistor Lready LSU power ready mm millimeter(s) Samsung Electronics 3-1 Reference Information Acronyms Acronym Definition Acronym Definition ADC Analog to Digital Converter LED Light Emitting Diode ALE Address-Latch Enable LSU Laser Scanner Unit ASCII American Standard Code for MHV Main High Voltage Information Interchange MPU Micro Processor Unit BIOS Basic Input/Output System NC No Connection BPS Bits Per Second PCB Printed Circuit Board CMOS Complementary Metal Oxide PCU Printed Control Unit Semiconductor PLCC Plastic Leaded Chip Carrier CPU Central Processing Unit PPM Page Per Minute DCU Diagnostic Control Unit PQFP Plastic Quad Flat Package DMA Direct Memory Access or PWM Pulse Width Modulation Dynamic Memory Access QFP Quad Flat Package Direct Memory Access Controller RAM Random Access Memory ROM Read Only Memory SCC Serial Communications Controller DMAC DOS Disk Operating System DPI Dots Per Inch (resolution) DRAM Dynamic Random Access Memory SMPS Switching Mode Power Supply DVM Digital Voltmeter SOP Small Outline Package EEPROM Electronically Erasable THV Transfer High Voltage Programmable Read Only Memory TS Tri-State Image Control Unit VCU Video Control Unit ICU 3-2 Samsung Electronics Reference Information 3-2 Chip Replacement (SMD) 3-2-1 Precautions for Chip Replacement 3-2-2 Tools for Chip Replacement 1. Do not directly touch any portion of the part with the soldering iron. ICs, especially TSOPs, are easily damaged by heat. The tools for chip replacement are as follows: · Thin tip type soldering iron. · Small flat-blade tip type soldering iron 2. Use care with the soldering iron tip and avoid rapidly heating parts. Some parts can be damaged by sudden heating. Preheat the part at about · Special desoldering tip iron · Air-blower Unit · Flat Package Pick-up o 100 C for several minutes before installing it. · Flux that can be cleaned by water o 3. Use a soldering tip temperature of about 240 C. For larger parts, use a slightly higher temperature o (about 280 C). 4. The thin (0.3mm) solder for miniature parts does not contain adequate flux. Supplementary flux is thus needed in most cases. Computer, OA and A/V systems are manufactured using flux which can be cleaned by water. When you replace the part or when troubleshooting, use proper flux and solder which can be cleaned by water. Improper flux may cause the soldering area to corrode and may cause a fatal system error. 5. Use care not to damage the circuit pattern, especially when desoldering. Because of the many pins, cleanliness of the pattern is extremely important after removing an IC. 6. Use care to avoid solder bridges. Remove any bridges that occur. 7. Position the part carefully. This also affects the soldering operation. Be very precise in positioning the IC. Soldering opposite pins first holds the IC in place and makes soldering the other pins easier. 8. Do not reuse removed parts. 9. Clock for solder joints, especially miniature parts with small lead. · 0.3mm thin solder that can be cleaned by water · Desoldering wire · Tweezers 3-2-3 Chip Resistor and Chip Capacitors TYPES The types of chip resistors and chip capacitor are as follows: · Thick Film Chip Resistors · Carbon Film Chip Resisters · Metal Film Chip Resisters · Chip Ceramic Capacitors · Chip Trimming Resisters REMOVING 1. Using Two soldering irons: a. Use thin tip soldering irons o b. Use soldering tip temperature of about 280 C. c. Simultaneously heat both ends of the part. d. While heating, grasp the part with the tips of the soldering irons and remove it. e. Use desoldering wire to completely remove the old solder from the part location on the board. A clean pattern for installing the new part is very important. 10. A defective trimming resistor cannot be adjusted externally. Replace with an ordinary variable resistor. 11. Always inspect the work with a magnifying lens. Check after installing cold solder joints, etc. Samsung Electronics 3-3 Reference Information INSTALLING INSTALLING 1. Clean the area where the new part is to be mounted. 2. Apply a water soluble flux. 3. Set part correctly into position and prevent is from shifting. 4. Bring the soldering iron tip close to the part contact without actually touching it. Melt thin (0.3mm) solder between the tip and part so that it flows into the part contact. 5. Check work quality with a magnifying lens. 1. Clean the area where the new part is to be mounted. 2. Apply a water soluble flux. 3. Set part correctly into position and prevent it from shifting. 4. Use a sharp soldering iron tip. Bring the tip close to the part contact without actually touching it. Melt thin (0.3mm) solder between the tip and part so that it flows into the part contact. 5. Check work quality with a magnifying lens. 3-2-4 Chip Tantalum Capacitors and Chip filters 3-2-5 Chip VRs, Chip Trimmer Capacitors, Diode and Tr. TYPES TYPES The types of chip tantalum capacitors and chip filters are as follows: The types of parts are as follows: · Chip VRs · Chip Trimmer Capacitors · Diode · Transistors · Chip Inductors · Chip Tantalum Capacitors · Chip Tantalum Electrolytic Capacitors · Chip Aluminum Electrolytic Capacitors · Chip Transformers · Chip Filters REMOVING 1. Using a special desoldering iron: a. Select soldering tip according to part size. b. Bring the tip into contact with the solder points. c. When the solder melts, remove the part. d. Remove the old solder with desoldering wire. REMOVING 1. Using two soldering irons. a. Use small-flat-blade tips. b. Heat the leads of the part simultaneously. c. When the solder melts, grasp and remove the part with the soldering iron tips. d. Remove the old solder with desoldering wire. 2. Using a special desoldering iron: a. Use small flat-blade tips. b. Heat both ends of the part simultaneously. c. When the solder melts, grasp and remove the part with the soldering iron tips. d. Remove the old solder with desoldering wire. 3-4 Samsung Electronics Reference Information INSTALLING INSTALLING 1. Clean the area where the new part is to be mounted. 1. Use desoldering wire to remove the previous solder 2. Clean the location. 2. Apply a water soluble flux. 3. Apply water soluble flux. 3. Set part correctly into position and prevent is from shifting. 4. Use a sharp soldering iron tip. Bring close to the part contact without actually touching it. Melt thin (0.3mm) solder between the tip and part so that it flows into the part contact. 4. Position the IC and solder two pins at opposite sides. 5. Use a sharp tipped soldering iron and carefully solder each pin. (After gaining experience, a thicker tip can be used for better work efficiency) 6. Remove any solder bridges with desoldering wire. 3-2-6 Chip ICs 7. Inspect the work with a magnifying lens. TYPES The types of chip ICs are as follows: 1. SOP (Small Outline Package) IC 2. SSOP (Shrink Small Outline Package) IC IC 3. VSOP (Very Small Outline Package) IC 4. QFP (Quad Flat Package) IC 5. VQFP (Very Quad Flat Package) IC 6. PLCC (Plastic Leaded Chip Carrier) IC 7. TSOP (Thin Small Outline Package) IC REMOVING 1. Using special desoldering iron: a. Select the tip according to the size shape of the IC. b.“Tin” the tip with a small amount of the IC leads. c. Set the tip squarely over the IC leads. d. When the solder melts, carefully twist the iron. e. Raise and remove the IC. 2. Using a shaped air-blower unit: a. Select the correct nozzle. b. Select the temperature and air-blow (suggested : temperature : 7, air-blow:4) c. Engage the IC removing tool. d. Use the air-blow the preheat the IC for about 5 seconds, then heat with the nozzle until the IC remove lifts the part from the board. Samsung Electronics 3-5 Reference Information 3-3 Recommended Test Equipment Samsung recommends the following equipment when servicing the Laser Printer. Digital Multimeter A digital multimeter with attached LED or LCD 4-digit Panel Oscilloscope A digitizing oscilloscope which can measure more than 100MHz High Voltage Probe A high voltage probe which can measure about less than 10KV DCU (Diagnostic Control Unit) DCU can be supplied from Samsung which can easily shows the engine’s error status Table 3-4-1 Equipment List Model :ML-6000 Series DocuPrint P1202 DIAGNOSTIC CINTROL UNIT QUICK REFERENCE 04 05 07 08 09 10 STATUS DIAGNOSTIC BIAS52 LSU READY 1ST PAPER ENVELOPE COVER OPEN OVER HEAT ON DIAGNOSTIC CODE 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 BIAS0 LSU MOTOR MP PAPER FEED SENSOR PRINT HEAT STANDBY SELF TEST OFF STATUS CODE MAIN MOTOR ON MHV ON THV "-"ON THV "+" REF VOLTAGE BIAS ON LSU ON PICK UP ON CHECK PAPER EMPTY SENSOR CHECK FEED EXIT SENSOR CHECK COVER SENSOR FUSER ON HOT BURNING CLEAN PRINT CHECK THV ON DUTY THERMISTER II CHECK FAN ON DCU MODE BIAS1 LSU MOTOR & LD SCF PAPER EMPTY EXIT SENSOR 00 01 02 03 04 05 20 22 23 30 31 40 50 60 61 62 64 68 70 71 72 73 90 94 95 99 DOWN READY(LEGAL) READY(LETTER) READY(A4) READY(EXECUTIVE) READY(B5) READY(FDLIO) PRINT START PRINT START(2’CASSETTE) PRINT START(MP TRAY) FEED SENSOR 1’st ON FEED SENSOR 1’st OFF FEED SENSOR 2’nd ON PAPER OUT OPEN FUSER ERROR WARM UP LOW HEAT ERROR COVER OPEN ERROR OVER HEAT ERROR NO PAPER or NO CASSETTE PAPER JAM0 PAPER JAM1 PAPER JAM2 MPF PRINT MODE NO PAPER in MP TRAY LSU NOT READY GREEN MODE SHIFT UP STOP ENTER IF YOU WANT TO ENTER THE DCU MODE. TURN THE POWER SWICH ON WHILE PRESSING ALL THREE KEYS. Figure 3-4-1 DCU 3-6 Samsung Electronics Reference Information 3-4 DCU Control 3-4-1 DCU Setup 1) Connect DCU to Controller Board Connector J6 (4 pins) or Engine Board CN2 (4pins). 2) To apply power, simultaneously press and hold down [DOWN], [SHIFT], and [STOP] keys. ‘78’ is displayed. 3) After 2-3 seconds, release the keys. ‘00’ is displayed. 4) Press [UP] or [SHIFT]+[DOWN] keys until the desired code number is displayed in the DCU display. 5) Press [ENTER] to begin operating. 6) Example : Select numbers ‘13’ and ‘14’ to adjust the electrophotography trigger voltage. 7) To end operation, press [SHIFT] and [STOP] keys. 3-4-2 DCU Diagnostic Mode The DCU is used to diagnose the printer malfunction status. Display Diagnostic Code Description 00 MAIN MOTOR ON 01 MHV ON 02 THV(-) ON 03 THV(+) REFERENCE ON 04 BIAS ON 05 LSU ON 06 PICK UP ON 07 CHECK PAPPER EMPTY SENSOR 08 CHECK FEED , EXIT SENSOR 09 CHECK COVER SENSOR 10 FUSER ON 11 HOT BURNING 12 CLEANING PRINT 13 CHECK THV ON DUTY 14 THERMISTER II CHECK 15 FAN ON Samsung Electronics 3-7 Reference Information 3-4-3 DCU Error Status Code DCU error code will indicate malfunction area of the machine. Display Error status 60 OPEN FUSER ERROR 62 LOW HEAT ERROR 68 OVER HEAT ERROR 64 COVER OPEN ERROR 70 NO PAPER or NO CASSETTE 71 PAPER JAM 0 72 PAPER JAM 1 73 PAPER JAM 2 95 LSU NOT READY 3-4-4 Error Solution Display 60, 62, 68 1. Measure the resistance of the AC connector on the Fuser. Normal resistance is 2-4 ohmsfor 110V, 6-8 ohms for 220V. 2. Check if the fuser lamp works properly. 3. Measure the resistance at Q101 on the engine board. If abnormal, replace Q101, Q3, PC151, Q8. 70 1. 2. 3. 4. 71 1. Make sure that paper is loaded in the cassette. 2. Check for pick-up unit. If it is heavily worn, replace it with new one. 3. Replace OP1 sensor. 72, 73 95 3-8 Solution 1. 2. 3. 4. Make sure that paper is loaded in the cassette. Replace OP2 sensor (photo interrapter). Check if the feed clutch works properly. If abnormal, replace the feed clutch or Q4 on the engine board. Make sure that the paper being used meets the specification. Check if there is a paper jam in the fuser. Replace OP1, OP3 on the engine board. Check the fuser roller for any dirt. If dirty, clean the roller. 1. Check for U205 on the engine board. 2. Replace LSU. 3. Measure the resistance at R62 and R8. If abnormal, replace them. Samsung Electronics 4. Disassembly and Reassembly 4-1 General Precautions on Disassembly When you disassemble and reassemble components, you must use extreme caution. The close proximity of cables to moving parts makes proper routing a must. If components are removed, any cables disturbed by the procedure must be restored as close as possible to their original positions. Before removing any component from the machine, note the cable routing that will be affected. Whenever servicing the machine, you must perform as follows: 1. Remove the paper cassette(s), and the print cartridge. Do not expose the cartridge to direct room light or sun light, and be careful not to scratch the drum surface. 2. Turn the power switch off. 3. Unplug all the cables from the printer. 4. Replace with only an authorized component. 5. Do not force to open or fasten a plastic material component. 6. Be careful no obstacles are included when you reassemble components. 7. When you reassemble components, be careful small size components are located in place. 8. If you turn the machine over to replace some parts, toner or paper particles may contaminate the LSU window. Protect the LSU window with clean paper. Releasing Plastic Latches Many of the parts are held in place with plastic latches. The latches break easily; release them carefully. To remove such parts, press the hook end of the latch away from the part to which it is latched. Samsung Electronics 4-1 Disassembly and Reassembly 4-2 Transfer Roller 1. Press the cover open switch and raise the printer cover. 3. Pull the roller slightly to the right to release the left end of the roller, then take it out. 2. Use a phillips screwdriver to release the right end of the roller. 4-2 Samsung Electronics Disassembly and Reassembly 4-3 Controller Board 1. Remove the cover located at the right side of the printer. 3. Unplug two connectors from the board. 2. Remove one screw. Slide the shield cover in the direction of OPEN arrow marked on the cover, then remove the cover. 4. Remove three screws securing the board and pull the board out of the printer. Samsung Electronics 4-3 Disassembly and Reassembly 4-4 Panel Board 1 Press the cover open switch and raise the printer cover. 4 Remove three screws from the board, and remove the board. 2 Remove two screws, unlatch the panel cap, then remove it. 5. Remove the Window LED and button panel LED. 3. Unplug one connector from the panel board. 4-4 Samsung Electronics Disassembly and Reassembly 4-5 Pickup Assembly 1. Turn the printer over. Remove three screws from the left base bracket, and take the bracket out. 2. Remove one ground screw. 3. Remove two screws securing the pickup assembly and take the assembly out. Push the solenoid if you have difficulty to remove the pickup assembly. 4. Check the pickup rubber wear. If the rubber is heavily worn, replace it with a new one. Squeeze this tab to remove the rubber. Samsung Electronics 4-5 Disassembly and Reassembly 4-6 MP (Multi-Purpose) Tray 1. Open the MP tray. 3. Rotate the MP tray upward to a 45O angle to unlatch the both ends of the tray, then take it out. 2. Release two stoppers. 4-6 Samsung Electronics Disassembly and Reassembly 4-7 Main Cover 6. Unlatch the front ends of the cover. 1. Before you remove the cover, you should remove: -Controller Board (see page 4-3) -Panel Board ( see page 4-4) -MP Tray (see page4-6) 2. Remove two screws at the back of the printer. Note: When you reassemble the cover, push the empty actuator in.If not, the cover is not in place. 3. Open the printer cover, and remove two screws. 7. Slide the main cover upward, out of printer. Note that the power switch is properly released when you remove the cover. Samsung Electronics 4-7 Disassembly and Reassembly 4-8 LSU 1. Before you remove the LSU, you should remove: 3. Remove three screws, and remove the LSU. Then unplug two connectors from the LSU. -Controller Board (see page 4-3) -MP Tray (see page xx) -Main Cover (see page 4-6) 2. Remove two screws securing the fuser cover, and remove the fuser cover. 4-8 Samsung Electronics Disassembly and Reassembly 4-9 Exit Assembly 1. Before you remove the exit assembly, you should remove: 4. If you want to remove the roller shaft, unlatch both ends of the shaft and take it out. -Controller Board (see page 4-3) -MP Tray (see page xx) -Main Cover (see page 4-6) -Fuser Cover (see page 4-10) 2. Remove three screws, and remove the bracket. 5. If you want to remove the exit rollers, sqeeze the bottom of roller and take it out. 3. Remove two screws, unlatch the exit tray and take it out. Samsung Electronics 4-9 Disassembly and Reassembly 4-10 Drive Assembly and Fan 1. Before you remove the drive assembly or fan, you should remove: 4. If you want to replace the fan, take it out. -Controller Board (see page 4-3) -Main Cover (see page 4-7) -MP Tray (see page 4-6) 2. Unplug four connectors. 5. If you want to remove the motor from the drive assembly, remove three gold screws securing the motor assembly to the gear bracket. 3. Remove seven screws securing the drive assembly from the gear bracket, and remove the drive assembly and motor drive board. Unplug one connector from the board. 6. Remove the motor assembly. Remove two screws securing the motor to the motor bracket, then take the motor out. 4-10 Samsung Electronics Disassembly and Reassembly 4-11 MP Plate Assembly 1. Before you remove the MP plate assembly, you should remove: -Controller Board (see page 4-3) -Main Cover (see page 4-7) -MP Tray (see page 4-6) 3. Remove seven screws securing the drive assembly from the gear bracket, and remove the drive assembly and motor drive board. Unplug one connector from the board. 2. Unplug four connectors. 4. Remove three screws, and remove the MP plate assembly. Samsung Electronics 4-11 Disassembly and Reassembly 4-12 Fuser 1. Before you remove the fuser, you should remove: 4. Remove the exit actuator. Unplug two connectors. -Controller Board (see page 4-3) -Main Cover (see page 4-7) -MP Tray (see page 4-6) 2. Remove three screws, and remove the bracket. Exit Actuator 5. Remove four screws, and remove the fuser assembly. 3. Remove two screws from the SMPS bracket. 4-12 Samsung Electronics Disassembly and Reassembly To remove the thermostat from the fuser assembly : Remove two screws, and take the thermostat out. To remove the halogen lamp from the fuser assembly : Remove one screw. Thermostat To remove the thermistor from the fuser assembly : 1. Release the wire from the three holders. 2. Remove one screw, then take the thermistor out. Note: When you reassemble the halogen lamp, make sure that it is inserted into the slot properly. Note: When you reassemble the thermistor, make sure that it puts in place. Samsung Electronics 4-13 Disassembly and Reassembly 4-13 MPF Assembly and Miscellaneous on MPF Assembly 1. Before you remove the MPF assembly, you should remove: -Controller Board (see page 4-3) -Main Cover (see page 4-7) -MP Tray (see page 4-6) 4. To replace the pickup roller on the MPF assembly: Squeeze the snap fit on the roller and remove the roller. 2. Unplug two connectors from the drive board. Snap fit To replace the damper gear on the MPF assembly : 1) Remove one screw, then remove the damp gear. 3. Remove five screws, then remove the MPF assembly. 4-14 Samsung Electronics Disassembly and Reassembly To replace the solenoid on the MPF assembly : 4) Pull the MPF bracket out in the direction of arrow. 1) Remove the spring. 2) Rotate the right end of the knockup plate until it is released, then take it out. 5) Unlatch the PE sensor, then take it out. 6) Remove two screws from the MP bracket, then remove the solenoid. 3) Remove two screws. Samsung Electronics 4-15 Disassembly and Reassembly To replace the pickup holder on the MPF assembly : 4) Remove the pickup guide. 1) Before you remove the pickup holder, you shoud remove the MP bracket (see page xx) and PE sensor (see page xx) on the MPF assembly. 2) Pull the pickup holder to the left and rotate it until the both ends of the holder are properly released, then pull it up. 5) Remove the holder pad. 3) Remove the pickup pad using a proper tool. 4-16 Samsung Electronics Disassembly and Reassembly 4-14 Engine Board and Miscellaneous 1. Before you remove the engine board, you should remove: 5. Remove three screws securing the ICU ground, and remove the ICU ground. -Controller Board (see page 4-3) -Main Cover (see page 4-7) -MP Tray (see page 4-6) 2. Remove the SMPS bracket as described in ‘4-10 Fuser’ and unplug four connectors. 3. Remove one screw from the engine board. 6. Remove one ground screw. 4. Turn the printer over. Remove six screws from the left and the right base brackets, and take them out. Samsung Electronics 4-17 Disassembly and Reassembly 7. Remove six screws securing the PCU shield. 9. Unplug all connectors from the PCU shield, and remove the shield. 8. While you push the stopper to release the PCU shield, take the PCU shield out of the printer. To replace HV terminals : Remove the terminals. Stopper HV terminals Note: When you replace with new ones, be careful that they are inserted in place. 4-18 Samsung Electronics Disassembly and Reassembly To replace the SCF connector : Remove two screws and take it out. To replace the pickup sensor : Take the sensor out while you push the both ends of the sensor. To replace the paper empty sensor : Take the sensor out while you push the both ends of the sensor inward. Paper empty sennsor Samsung Electronics 4-19 Disassembly and Reassembly To replace the actuator : 1. Turn the mechanism back and push down the points as shown to unlatch the actuator. To remove the transfer guide : Remove four screws and take the guide out. M3 x 8 2. Turn the unit over, and remove the actuator. To replace the PTL module : Release the three tabs latching the sensor using a phillips screwdriver, then push the sensor down. 4-20 Samsung Electronics Disassembly and Reassembly To replace the transfer roller bushings (left and right) : Release each tab latching the left and right holder, then push the holder down. To replace the thermistor assembly : Remove one screw, and remove the thermistor assembly. Note: When you reassemble the thermistor assembly, make sure that it puts in place. Samsung Electronics 4-21 Disassembly and Reassembly 4-15 Cover Open Sensor 1. Before you remove the sensor, you should remove: 4. Remove two screws, then remove the sensor. -Controller Board (see page 4-3) -Main Cover (see page 4-7) -MP Tray (see page 4-6) -Engine Board (see page 4-17) 2. Remove one screw, then remove the ICU shield. 3. Remove two screws securing the sensor to the main frame. 4-22 Samsung Electronics Disassembly and Reassembly 4-16 ROM 1. Press the cover open switch and raise the printer cover. 3. Replace ROM using the specified jig. Note: When you install a new ROM, be careful for the direction. 2. Remove the ROM cover. Samsung Electronics 4-23 Disassembly and Reassembly Memo 4-24 Samsung Electronics 5. Troubleshooting Error code 1-010 Fault Black vertical stripes Model ML-6100 Description Black vertical stripes occur in the printing. Check 1. Developer cartridge 2. Transfer roller 3. Charge roller Cause 1. Defective develop roller or bad blade of toner cartridge. 2. Defective transfer roller or charge roller. Solution 1. Replace the toner cartridge, if defective. 2. Replace the roller defective. Remark Others Samsung Electronics 5-1 Troubleshooting Error code 1-020 Fault White vertical stripes Model ML-6100 Description White vertical voids in the image. Check 1. LSU 2. Developer cartridge 3. Fuser Cause 1. Foreign matter stuck onto the window of internal lens of LSU mirror 2. Foreign matter or toner particles between the developer roller and blade 3. If the fuser is defective, voids occur periodically at the top of a black image. Solution 1. Clean the LSU window with a recommended cleaner, or replace the LSU window. 2. Replace the developer cartridge if defective. 3. Open rear cover and check ribs in the fuser for contamination. Clean if necessary. Remark Use LSU cleaner dated after January 1997. Others If white streaks occurs fewer than 5 or 6 times, it can be considered as normal. 5-2 Samsung Electronics Troubleshooting Error code 1-030 Fault Black horizontal stripes Model ML-6100 Description Dark or blurry horizontal stripes occur in the printing periodically. Check Developer cartridge Cause 1. Bad contacts of the voltage terminals to developer 2. The rollers may be stained with toner particles. * Abnormal image periodicity : 37.7 mm = Charge roller 31.3 mm = Supply roller 94.2 mm = OPC drum 46 mm = Develop roller non periodical = Blade Solution 1. Check all voltages, and adjust as necessary. 2. Check for terminal contacts, and replace the cartridge, if necessary. Remark Others Samsung Electronics 5-3 Troubleshooting Error code 1-040 Fault Black or white spots Model ML-6100 Description Dark or blurry black or white spots occur periodically. Check 1. Developer cartridge 2. Transfer voltage 3. Transfer roller’s life Cause 1. If dark or blurry black spots occur periodically, the rollers in the Developer may be contaminated with foreign matter or paper particles. (Charge roller : 37 mm interval, OPC drum : 94 mm interval). 2. If faded areas or voids occur in a black image at intervals of 94 mm, or black spots occur elsewhere, the OPC drum surface is damaged. 3. If a black image is partially broken, the transfer voltage is abnormal or the transfer roller’s life has expired. Solution 1. Run OPC cleaning to remove excess toner and paper particles on the charge roller and OPC drum. Repeat 2 or 3 times. Run the self-test. If the same problem persists, replace the developer. 2. Clean the rollers. If problem persists, replace the Developer. 3. The transfer roller guarantees 50,000 sheets printing. If the roller’s life is expired, replace it. Remark Others 5-4 Samsung Electronics Troubleshooting Error code 1-050 Fault Light image (1) Model ML-6100 Description The printed image is light, with no ghost. Check Developer cartridge Cause 1. The life of cartridge is ended. 2. Ambient temperature is below than 10 oC. 3. Agitator gear in the Developer is defective. 4. Bad contact of supply roller and abnormal supply voltage. Solution 1. Check the weight of the developer cartridge, and replace if necessary. When the cartridge is almost used up, the weight will be as follows: ML+6000D5 : 960 grams +/- 20 grams 2. In low temperature, wait 30 minutes after printer is powered on before you start printing. 3. Check if the hopper gear is visible from the side of the developer. If not, replace the developer. 4. Check for the supply roller contact and the supply voltage. Remark Others Samsung Electronics 5-5 Troubleshooting Error code 1-051 Fault Light image (2) Model ML-6100 Description The printed image is light, with no ghost. Check Engine board Cause 1. Charge voltage (=MHV) on the engine board exceeds 1520V. (Perform DCU diagnostic mode 01 to measure the voltage). 2. No power to the supply roller. Solution Check the following parts and replace if defective : U201(KA324), Q211(C1008), T202(Transformer), resistors, and diodes in the output and feedback area. Remark Check the charge voltage (MHV) at : U201; while operating, #10/#9 2.5~2.9V, #8 5.5~8.5V while idling, #9 2.7V, #10/#8 0V Q201 operating voltage; Base 2~2.5V, Emitter 0~1V, Collector 30~60V U203; #1 0V input, #2 0V output Others 5-6 Samsung Electronics Troubleshooting Error code 1-052 Fault Light image (3) Model ML-6100 Description The printed image is light, with no ghost. Check 1. Engine board 2. Main body Cause 1. Engine board bias (350-485V) and supply voltage (570-630V) may be low (Perform DCU diagnostic mode 04 to measure the voltage). 2. Direct strong light may be entered into the manual feed slot. Solution 1. Check the following parts : U201(KA324), Q204(D526-Y), T204(Transformer), U203(SN7407N), resistors, diodes in the output and feedback area. 2. Check if contrast mode is set to ‘Light’. If not, change the install position of the printer or attach OPC cover sheet (P/No: JC72-49093A). Remark Bias and supply voltage check point: U203; #9 pulse input, #8 pulse output Others Samsung Electronics 5-7 Troubleshooting Error code 1-060 Fault Dark image (1) Model ML-6100 Description The printed image is dark. Check Engine board Cause 1. No charge voltage in the engine board. (Perform DCU diagnostic code ‘01’ to measure the voltage). Solution 1-1. Check the following parts : U201(KA324), Q211(C1008), Q201(D526-Y), T202, U203 (SN7407N), resistors, diodes in the output and feedback area. 1-2. Clean the high voltage terminal on the engine and its PBA. 1-3. Refer to the following information. U201(KA324)’s pin #12, #13 ; 2.5~2.9 V, pin #14 ; 5.5~8.5 V For standby, pin #13 ; 2.7V, pin #12 & #14 ; 0V Q201’s operating voltage ; base=+2~2.5 V, emitter=0~1 V collector=30~60 V U203(7407N)’s pin #1 ; 0V input, pin #2 ; 0V output Remark Others 5-8 Samsung Electronics Troubleshooting Error code 1-061 Fault Dark image (2) Model ML-6100 Description The printed image is dark. Check Engine board Cause 1. No supply or bias voltage at the engine board (Perform DCU diagnostic code ‘04’ to measure the voltage). Solution 1-1. Check the following parts : U201(KA324), Q204(D526-Y), T204, U203 (SN7407N), resistors, diodes in the output and feedback area. 1-2. Refer to the following information. U203(7407N)’s pin #1; pulse input, pin #2; pulse output. Remark Others Samsung Electronics 5-9 Troubleshooting Error code 1-062 Fault Dark image (3) Model ML-6100 Description The printed image is dark. Check Engine board Cause 1. Voltage higher than normal. (normal supply voltage : 570-630V, normal bias voltage : 350-485V). Solution 1-1. Check the following parts : U201(KA324), Q204(D526-Y), T204, U203 (SN7407N) resistors, diodes in the output and feedback area. 1-2. Refer to the following information. U203(7407N)’s pin #9; pulse input, pin #8; pulse output. 1-3. Check developer contacts for contamination by toner particles. Remark Others 5-10 Samsung Electronics Troubleshooting Error code 1-070 Fault Uneven density Model ML-6100 Description Print density is uneven between left and right. Check 1. Transfer roller pressure 2. Developer cartridge Cause 1. The pressure force on the left and right springs of the transfer roller is not even (left : 450 gf, right : 600 gf), the springs are damaged, the transfer roller is improperly installed, or the transfer roller bushing or holder is damaged. 2. The toner level is not even on the developer roller due to the bad blade. Solution 1. Replace defective holder or springs. Adjust the transfer voltage. 2. Replace the developer cartridge. Remark Others Samsung Electronics 5-11 Troubleshooting Error code 1-080 Fault Background Model ML-6100 Description Background appears in the printing. Check 1. Engine board 2. Developer cartridge 3. Transfer roller 4. Operating environment Cause 1-1. Low transfer voltage (10% below than normal) 1-2. High supply and / or bias voltage. 1-3. No transfer voltage. 2. Unauthorized recording paper has been used. 3. Abnormal ambient temperature or humidity. 4. Defective develop roller. Solution 1-1. Refer to Error Code 1-060. 1-2. Refer to Error Code 1-061. 1-3. Refer to Error Codes 1-090 and 1-091. 2. Use a recommended type of recording paper. 3. If the printer is under abnormal ambient condition for a long time, print errors may occur. Improve the operating environment. 4. Replace the toner cartridge. Remark Others 5-12 Samsung Electronics Troubleshooting Error code 1-090 Fault Ghost (1) Model ML-6100 Description Ghost occurs at 94 mm intervals. Check 1. Developer cartridge 2. Main body Cause 1. Contamination of high voltage terminals in the main body , engine board, and / or developer. 2. Transfer roller lifetime has expired. 3. No using recommended recording paper. 4. The Pre-Transfer Lamp (Refer to 18 on page 6-6.) Solution 1. Open top cover and disassemble the unit and clean contamination components. 2. After replacing the transfer roller, make sure the transfer voltage is normal. 3. Use a recommended type of recording paper. 4. Check for the PTL operation, and if required, check for the main board. Remark Others Samsung Electronics 5-13 Troubleshooting Error code 1-090-1 Fault Ghost (2) Model ML-6100 Description Ghost occurs at 94 mm intervals. Check Operating environment Cause 1. Abnormal low temperature and humidity. In this case, ghost occurs on the entire page and the print density is too light. Solution 1. If the operating temperature and relative humidity are too low, try waiting about 1 hour after power on before using printer. Remark Others 5-14 Samsung Electronics Troubleshooting Error code 1-091 Fault Ghost (3) Model ML6100 Description When xerographic paper is used in ADF, ghost occurs at 94 mm intervals. Check Engine board Cause 1. No minus (-) transfer voltage output from the engine board. (Normal voltage : 1250 -1450V with 660 Mohm load) 2. The (+) transfer voltage may be abnormal when performing DCU #13 with 660 Mohm load on the transfer voltage output. (Normal voltage: 2200V (+30/-30V) DCU #14, 3250-3350V DCU #13). Solution Check the following parts : U201(KA324), Q207(A708), Q202(KSD526-Y), T201, U203 (SN7407), resistors, or diodes in the output and feedback area. Remark Others In case of no minus transfer output voltage, image quality may be poor, and background may occur in the printing. Samsung Electronics 5-15 Troubleshooting Error code 1-093 Fault Ghost (4) Model ML-6100 Description When printing on card stock or transparencies using manual feeder, ghost occurs at 94 mm intervals. Check 1. Selected paper type in the software application 2. Engine board Cause 1. When printing on card stock or transparencies, higher transfer voltage is required. Select ‘Thick Mode’ on paper type menu from the software application. 2. Defective transfer voltage terminal in the engine board. Solution 1. Select ‘Thick Mode’ on paper type menu from software application to print on card stock or transparencies. 2. If the transfer voltage in the engine board is out of specification, refer to Error Code 1-091 Remark Others 5-16 Samsung Electronics Troubleshooting Error code 1-094 Fault Ghost (5) Model ML-6100 Description Dark ghost occurs in printing at 69 mm intervals Check Fuser Cause The heat roller and pressure roller in the fuser are contaminated with toner or paper particles. Solution Open the rear cover and check if the heat roller is stained. If stained, disassemble the fuser and clean the rollers with soft cloth dampened with alcohol. If ghost still occurs, replace the fuser. Remark Others Samsung Electronics 5-17 Troubleshooting Error code 1-095 Fault Ghost (6) Model ML-6100 Description White ghost occurs in the black image printing at 46 mm intervals. Check 1. Developer cartridge Cause 1. The life of the developer may be expired. 2. Abnormal transfer voltage or bad contact of the transfer roller Solution 1. Measure the weight of the developer and replace if the weight is less than 960g +/-20g. 2. Check the supply voltage and adjust if necessary. Check for the contact. Remark Others 5-18 Samsung Electronics Troubleshooting Error code 1-100 Fault Partial blank image Model ML-6100 Description Partially blank image appears either periodically or non-periodically. Check 1. Transfer roller 2. Developer cartridge Cause 1. The pressure force on the left and right transfer roller springs are not even, the springs are damaged, the transfer roller is improperly installed, or the transfer roller bushing or holder is damaged. 2. If a black image prints light or gradually light at intervals of 49 mm, the transfer roller is defective. 3. If there is a partial blank image on left and right side of the page: 1) The life of the transfer roller has expired. 2) Abnormal transfer voltage. 3) The life of the developer has expired. Solution 1. Replace the defective components. 2. Replace the transfer roller. 3-1. Replace the transfer roller. 3-2. Measure the transfer voltage. If the voltage is abnormal, disassemble the main board and clean the components stained with toner or paper particles. 3-3. Measure the weight of the developer. If the weight is less than 960 g ±20 g, replace the developer. Remark Others Samsung Electronics 5-19 Troubleshooting Error code 1-110 Fault Stains on the face of page Model ML-6100 Description Background too dark on the face of printed page Check 1. Developer cartridge 2. Main body Cause 1. Toner leakage due to improperly sealed developer. 2. Transfer roller length is out of spec. (218 mm) or the roller is defective. 3. The inside of the unit is contaminated with toner or paper particles. Solution 1. Clean the unit thoroughly. If problems still occurs, replace the developer. 2. If the roller is shorter than the recording paper or the roller is severely stained, replace the roller. 3. Clean the contaminated components. Remark Others 5-20 Samsung Electronics Troubleshooting Error code 1-111 Fault Stains on back of page Model ML-6100 Description The back of the page is stained at 49 mm intervals Check Transfer roller Cause 1. Transfer roller is contaminated. 2. Abnormal (+) (-) transfer voltage, or cleaning voltage. 3. Defective transfer roller Solution 1. Clean the transfer roller thoroughly. Replace if contaminated severely. 2. Adjust the voltages. 3. Replace if necessary. Remark Others Samsung Electronics 5-21 Troubleshooting Error code 1-120 Fault Blank page printout Model ML-6100 Description Blank page is printed. Check 1. Bad ground contacts in OPC and/ or developer. 2. Seal tape on the cartridge Cause 1. GND OPC is not well grounded. 2. Seal tape is not removed. 3. Low toner Solution 1. Repair or replace the GND terminal. 2. Remove the seal tape. 3. Shake the toner cartridge and print. Or replace with new one. Remark Others 5-22 Samsung Electronics Troubleshooting Error code 1-121 Fault Partial black image Model ML-6100 Description One or several blank pages are printed. When the printer turns on, several blank pages print. Check Control board Cause Defective control board Solution 1. Perform the engine self test using DCU. If blank page prints, the control board is defective. If the printer works normally, refer to next solution (2). If the control board is defective, check the connection on the control board, QP1700 pin 125, and 202. 2. If blank page is printed one time or continuously, check that the video controller oscillates properly at 47.7789 MHz. (lower than 0.75V, higher than 3.5V) 3. If blank pages prints continuously when the printer turns on, check the CPU works properly, and replace if defective. Remark Others Samsung Electronics 5-23 Troubleshooting Error code 1-130 Fault Data error Model ML-6100 Description Incomplete or missing characters. Check Control board Cause 1. Bad connections of port 2. Defective oscillators in the video controller. 3. Defective CPU in the video controller. Solution 1. Check that the port and related parts are properly connected or soldered. 2. Check the oscillators (47.7789 MHz, 50MHz) on the video controller. 3. Replace the CPU on the video controller. Remark Others 5-24 Samsung Electronics Troubleshooting Error code 1-140 Fault Poor fusing grade (1) Model ML-6100 Description When printing on xerographic paper from cassette, the printed image is diffused. Check Engine board Cause Defective the fuser (Heat lamp) control circuit in the engine board. Solution Refer to solution 2-1 under Error Code 3-011. Remark Others Samsung Electronics 5-25 Troubleshooting Error code 1-141 Fault Poor fusing grade (2) Model ML6100 Description When printing on card stock or transparencies using manual feeder, the printed image is diffused. Check 1. Improper paper type menu setup 2. Engine board Cause 1. When printing on card stock or transparencies, higher transfer voltage is required. 2. Defective transfer voltage circuit in the engine board. Solution 1-1. Select ‘Thick Mode’ on paper type menu from the software application to print on card stock or transparencies. 1-2. Check the fuser control circuit. Refer to Solution 2-1 under Error Code 3-011. 2. Check the transfer voltage and adjust if necessary. Remark Others 5-26 Samsung Electronics Troubleshooting Error code 2-010 Fault Wrong print position Model ML-6100 Description Printing begins at wrong position on the paper. Check Feed sensor actuator, LSU, Pick-up ass’y, Bracket-dust, Solenoid, Video Controller. Cause 1. Wrong sence time caused by defective feed sensor actuator. 2. Skew: Bad LSU-assembling Uneven pressure force of the pick-up ass’y Defective mechanical parts 3. Top margin; Early feeding by the solenoid Wrong OP1 sensor position Wrong video controller connection Solution 1. Replace the defective actuator. 2. Reassemble or replace the LSU. Reassemble or replace the pick-up ass’y. Reassemble or replace the defective mechanical parts. (for example, Bracket-dust). 3. Replace the solenoid. Check OP1. Check the Vedio Controller or its connection. Remark Others Samsung Electronics 5-27 Troubleshooting Error code 2-020 Fault Jam 0 Model ML-6100 Description 1. Paper is not exited from the cassette. 2. Paper is stopped just after cassette, before feed sensor, or on the feed sensor. Check Engine board Cause 1. Open the printer cover, and close it. Then check : 1-1. If the paper does not feed into the printer, the feed clutch driving circuit in the engine board may be defective. 1-2. If the paper feeds into the printer and ‘Jam 0’ occurs, the feed sensor OP1 on the engine board may be defective. 2. Defective PLT-Knockup (12) (Refer to 9 on page 6-14.) Solution 1. Check for the solenoid driving circuit using DCU diagnostic mode 06. 1) Check for 24V input on D1 cathode. If 24V is not present, check Q4. If they work normally, check for 24V output from SMPS. 2) Measure the feed clutch resistance. Replace if not approximately 60 ohms. 3) Check Q4. if Q4 is OK, the collector and base should be 0V and 0.7V DC to GND, respectively. 2. Check for Feed sensor OP1 and related parts. 1) Replace Feed sensor actuator if defective. 2) When OP1 sensor is blocked, U6 (74HC245) pin#16 should be over 3.5V. When the sensor is not blocked, the pin should be below 0.7V. One side of R15 in OP1 transmitter should be 5V, and the other end 1.2V. If normal, check OP1 receiver. If not shorted, replace CPU. 3. Replace the cassette, if damaged. Remark Others 5-28 Samsung Electronics Troubleshooting Error code 2-030 Fault Jam 1 Model ML-6100 Description Recording paper is jammed in the output area (inside the fuser), or multiple sheets of the paper are fed at once. Check Engine board Cause 1. Open the printer cover, and close it. Then check : - If the paper does not feed into the printer, the feed clutch driving circuit in the engine board may be defective. - If the paper feeds into the printer and ‘Jam 1’ occurs, the feed sensor OP1 on the engine board may be defective. - If paper is stopped in just front of fuser: 1-1. Feed sensor OP1 or feed actuator may be defective. 1-2. Exit sensor OP3 or exit actuator may be defective. 2. In case of multi-feeding, refer to Error Code 2-050. Solution 1-1. Check the feed sensor OP1. Refer to Error Code 2-020. Replace the feed actuator if defective. 1-2. Check OP contacts. In operating mode, U6 (74HC245) pin#13 should be below 0.7V. If not, check OP3 contact resistance. Replace OP3 if over 100 ohms. If the switch works normally, check R30. If defective, replace the exit sensor actuator. 2. In case of multi feeding, refer to Error Code 2-050. Remark Others Samsung Electronics 5-29 Troubleshooting Error code 2-040 Fault Jam 2 Model ML-6100 Description Paper is completely fed out of the printer, but Jam 2 occurs. Or, the paper is stuck in the fuser roller. Check 1. Engine board 2. Fuser Cause 1. Check if paper is jammed in the pressure roller. 2. Open the printer cover, and close it : If Jam 2 occurs after the paper is completely fed out of the printer, the exit sensor contact may be bad or the exit sensor actuator may be deformed. Solution 1-1. Check if the exit sensor actuator is defective, and replace if required. 1-2. Check the exit sensor OP3 contact and related parts. Refer to Error Code 2-030. 2. If the paper is stuck in the fuser, disassemble the fuser and remove the jammed paper, and clean the surface of the pressure roller with soft cloth, dampened with alcohol. Remark Others 5-30 Samsung Electronics Troubleshooting Error code 2-050 Fault Multi-feeding Model ML-6100 Description Multiple sheets of paper are fed at once. Check Engine board Cause 1. Solenoid malfunction. 2. Feed clutch armature does not engage the pick-up housing in the pick-up ass’y. Solution 1. If the solenoid does not work properly: 1-1. Measure the resistance of the feed clutch coil. If below 40 ohm (normal: 55-60 ohm), replace. 1-2. Check Q4 C/E short, and replace as necessary. (If C and E are shorted, multiple sheets of paper feed when the printer powers on.) 1-3. Check if the solenoid spring is returned to the original state. Replace if the return force is weak. 2. If the clutch works properly, but the armature does not engage the pick-up housing in the pick-up ass’y, bend the armature to pick up properly. Remark The feed clutch spring has 40 turns. A pad is attached to solenoid yoke, the armature angle is 90 degrees. Others Samsung Electronics 5-31 Troubleshooting Error code 3-010 Fault Fuser Error Model ML-6100 Description All the lamps on the operator panel blink and the system stops. Check 1. Fuser 2. Engine board Cause 1-1. Thermostat, AC wire, or heat lamp may be open. 1-2. Thermistor may be open. (DCU error code 60, 62, 68.) 2-1. Abnormal heat lamp on/off 2-2. Malfunction of the overheat circuit Solution 1-1. Check thermostat, AC wire, and heat lamp. If the thermostat is open, check also R37, R47, or Q8. 1-2. If thermistor is open, check the wire. If the wire is good, check Q8. Q8 collector should be 0.2V, base 0.7V. 2-1. Check Q3 and its related parts in the order shown below. 1) Check Q3 C-E, B-E, B-C, and replace if shorted. If the voltage between B and E is below 0.7V, replace the transistor. 2) When lamp is on, if the base is 0V, check CPU pin 38. 3) When lamp is on, if the collector is 0V with lamp off, check PC151, Q101, and its related parts. 2-2. Check the overheat circuit. When U5 pin 7 is below 0.5V, the overheat circuit should activate and the lamp turns off. In normal mode, pin 6 is approximately 2.6V, pin 5 is over 2.6V, and pin 7 is over 4V. If not, check all related parts. Remark Others 5-32 Samsung Electronics Troubleshooting Error code 3-011 Fault Malfunction of the gear motor in the fuser Model ML-6100 Description When printing, motor breaks away from its place due to the defective fuser gear. Check 1. Fuser 2. Engine board Cause 1. Fuser control temperature is set too high. 2. PC151 or Q3 is defective. 3. Overheat circuit is not operating properly. Solution 1-1. Check if the thermostat is open, and replace. 1-2. Check if the thermistor sensor is in place, and replace if required. 2-1. R57 and R58 = 3.3k and 1k, respectively. Check if R57 and R58 are 3.3K and 1K respectively. 2-2. Replace Q3 if C and E are short. 2-3. Replace PC151 if pin 4 and 6 are short. 2-4. Replace Q101 if T1 and T2 are short. 3. Check if the overheat circuit works properly : Refer to the solution 2-2 under ‘Error Code 3-010’. Remark Others Samsung Electronics 5-33 Troubleshooting Error code 3-020 Fault Scanner Error Model ML-6100 Description The feeding paper is stopped in the front of transfer roller and all lamps on the operator panel blink. Check 1. LSU 2. Engine board Cause 1. Defective LSU 2. Defective Q5, or CPU 3. Abnormal resistance value of R8, R62 Solution 1. Perform DCU diagnostic code 05. If the DCU error code 95 is displayed, replace LSU. If you cannot solve the problem after you replace LSU, follow the steps below. (1) When you press ENTER key with DCU code ‘05’, if the LSU motor does not run, check U205 pin 5, pin 6. If U205 pin 5, and pin 6 are normal, check CPU pin 40 and the related parts. If the motor drives properly, and CPU pin 25 is not below 0.5V, replace R51 and CPU. (2) When you press UP key with DCU code ‘05’, if ON and OFF lamps do not turn on, check CPU pin 28 and 41, and their related parts. Normally pin 28 is over 3.5V when high, and below 0.7V when low. If the transformer works normally, replace CPU. Remark Others Q3, U3, CN3, SW151 5-34 Samsung Electronics Troubleshooting Error code 3-030 Fault Paper Empty Model ML-6100 Description • The PAPER lamp on the operator panel is on even when paper is loaded in the cassette. • The PAPER lamp on the operator panel does not come on when the paper cassette is empty. Check 1. Actuator-Empty (Refer to 52 on page 6-6.) 2. Engine board Cause 1. Empty actuator may be defective. 2. Photo sensor OP2 on the engine board may be defective. Solution 1. Replace the defective actuator. 2-1. U6 (74HC245) pin 15 should be over 3.5V when OP2 sensor is blocked, and below 0.7V when the sensor is not blocked. 2-2. One end of R24 in the transmitter of OP2 should be 5V, and the other end 1.2V. 2-3. If the related resistors are good, check for short circuit of OP2 receiver. If OP2 is normal, replace U6 (74HC245). Remark Others Samsung Electronics 5-35 Troubleshooting Error code 3-040/3-041 Fault Cover Open Model ML-6100 Description • The ERROR lamp is on even when the printer cover is closed. • The ERROR lamp does not come on even when the printer cover is open. Check 1. Hook lever in the top cover (Refer to 2 on page 6-4.) 2. Engine board 3. Actuator-cover open (Refer to 48 49 on page 6-6.) Cause 1. The hook lever may be defective. 2. Malfunction of the circuit containing the micro switch SW151 and its related parts on the engine board. 3. Defective actuator-cover open. Solution 1. Replace the hook lever, if defective. 2. Check SW151 and its related parts : 2-1. Check SMPS 24V output. 2-2. Check D4 anode when SW151 is pressed. D4 anode will be below 3.5V when SW151 is open. Check for R38 and R39, and replace if defective. 2-3. If D4 anode is over 3.5V, check if CPU pin 48 is short. If not, replace CPU. 3. Replace the defective actuator. Remark Others 5-36 Samsung Electronics Troubleshooting Error code 3-050 Fault All Lamps Blinking Model ML-6100 Description When printer power is on, all lamps on the operator panel blink. Check 1. Harness between the engine and control boards 2. Engine board Cause Defective interface between the engine board and control boards (DCU error code ‘78’) Solution 1. Check the harness between the engine and control boards. 2-1. Check if the engine board works properly when the printer resets. U5 pin 1 should be below 0.7V for about 122 ms after power is on, then remain over 3.5V. -Check U5 pin 2 = approx. 3.8V. If so, check R54 or R55. -Check U5 pin 3 = approx 4V. If so, check R53 or R56, or C35. -If the voltages are normal, and U5 pin 1 is below 0.7V, replace U5. -If all are normal, check CPU pin 55. If OK, replace CPU. 2-2. Check for X1 oscillation (6.94407MHz). 2-3. Replace EPROM in the engine board, if defective. 2-4. If all above are OK, replace CPU. Remark Others U4, U202, Q9 Samsung Electronics 5-37 Troubleshooting Error code 3-060 Fault Memory Overflow Model ML-6100 Description When printing, error message is printed out. Check Control board Cause Insufficient printer memory. Solution Install optional SIMM memory in the control board. Remark Others 5-38 Samsung Electronics Troubleshooting Error code 3-080 Fault Defective motor operation Model ML-6100 Description Main motor is not driving when printing, and paper does not feed into the printer, resulting ‘Jam 0’. Check 1. Engine board 2. Sub motor board (Refer to 12 on page 6-6.) Cause 1. Motor harness or CN104 may be defective. 2. U1 defective in the sub motor board. Solution 1. Check the motor harness. replace it, if defective. 2-1. Perform DCU diagnostic code 00 and check the motor operation. 2-2. With DCU code ‘00’, check for pulse at U1 pin 8 and pin 13. Or, check the related parts. 2-3. With DCU code ‘00’, check U1 pin 4 and pin 17 are over 4V. If the pins are below 1V, check R424. 2-4. If all above are OK, replace U1. Remark Others Samsung Electronics 5-39 Troubleshooting Error code 3-090 Fault Ear-splitting noise or allophone Model ML-6100 Description While operating, ear-splitting noise occurs. Check LSU motor, Main motor bracket, Fan, Developer, Fuser gear Cause 1. Defective LSU motor and main motor bracket, or defective harness 2. Foreign materials in the fuser gear or developer Solution 1-1. Replace the LSU, if defective. 1-2. Check the main motor bracket or its wiring harness. 1-3. Check pick-up ass’y rolls. 2. Reassemble or replace the fuser and developer if defective. Remark Others 5-40 Samsung Electronics Troubleshooting Error code 3-100 Fault No power Model ML-6100 Description When system power is turned on, all lamps on the operator panel do not come on. Check Engine board Cause 1. Defective harness between engine and control boards. 2. Defective harness between the control board and panel. 3. Defective fuse F151 4. Defective fuse F101 5. BD101 short. Check for the resistance value of Q102. 6. Defective U101 Solution 1. Check the connection between engine and control boards, and replace, if defective. 2. Check the connection between control board and operator panel. If defective, replace the harness. 3. Check F151 on the engine board. If open, measure the resistance between 5V and ground. If it is below 50 ohm, it is short. 4. Check F101 on the engine board. If open, check also : - R114 open - Q102, D-S, G-D, or G-S short - Defective BD101 Remark Others Samsung Electronics 5-41 Troubleshooting Error code 3-110 Fault Vertical line getting curved Model ML-6100 Description When printing, vertical line gets curved. Check LSU Engine board Cause 1. For LSU, +24V supply is unstable in the engine board. 2. Difference according to LSU vendors Solution • Check the capacitor between CN 3 pin 5 and +24V is 100nF. • Check the resistor R63 (12.1Kohm). • Replace LSU. • Replace the main board. Remark Others 5-42 Samsung Electronics Troubleshooting Fault All LEDs On Model ML-6100 Description When turning on, all LEDs are continuously on. Check Fuser, LSU, Engine board Cause 1. Fuser error 2. LSU error 3. Bad connection between engine board and control board. Solution 1. Replace the fuser. 2. Replace the LSU. 3. Check the wiring between the engine board and the control board. 4. Replace engine board. Remark Others Samsung Electronics 5-43 Troubleshooting Fault Jitter Model ML-6100 Description When printing, image is irregular. Check LSU, Motor bracket Cause 1. LSU hexahedron period 2. Defective motor bracket gears Solution 1. Replace the LSU. 2. Replace the motor bracket ass’y. Remark Others 5-44 Samsung Electronics 6. Exploded Views and Parts List 6-1 Main Exploded View 6-2 Main Parts List 6-3 Frame Ass’y Exploded View 6-4 Frame Ass’y Parts List 6-5 Cover Ass’y Exploded View 6-6 Cover Ass’y Parts List 6-7 MP-Tray/MPF Exploded View 6-7-1 MP-Tray Exploded View 6-7-2 MPF Exploded View 6-8 MP-Tray/MPF Parts List 6-8-1 MP-Tray Parts List 6-8-2 MPF Parts List 6-9 Motor-Main Exploded View 6-10 Motor-Main Parts List 6-11 Fuser Ass’y Exploded View 6-12 Fuser Ass’y Parts List 6-13 Pick-Up Exploded View 6-14 Pick-Up Parts List 6-15 Cassette Exploded View 6-16 Cassette Parts List 6-17 Second Cassette Frame Exploded View (option) 6-18 Second Cassette Frame Parts List (option) 6-19 Second Cassette Exploded View (option) 6-20 Second Cassette Parts List (option) Samsung Electronics 6-1 Exploded Views and Parts List 6-1 Main Exploded View 0 3 5 8 4 2 7 19 6 18 20 1 14 9 13 12 11 10 16-2 16-1 15 16 17 6-2 Samsung Electronics Exploded Views and Parts List 6-2 Main Parts List NO Seq Ass’y Name Ass’y Code Part Name Sub Code Q’ty 1 Frame Ass’y 2 UNIT-LSU 17833RPM 3 Cover Main Ass’y 4 MEA RACK-MP TRAY JC97-01202D 1 5 MEA RACK-MPF JC97-01201A 1 6 ELA-Hou- Motor Main JC96-01099A 1 7 PBA MAIN-MOTOR SUB JC92-01045A 1 8 Fuser Ass’y 9 MEA RACK-FEEDER JC97-01078A 1 10 MEA RACK-CAST_A4 JC97-01261A 1 11 MEA RACK-BOTTOM L JC97-01103B 1 12 MEA RACK-BOTTOM R JC97-01102B 1 13 IPR-SHIELD SIMM JC70-10234A 1 14 PMO-COVER SIMM JC72-41224A 1 15 IPR-SHIELD SMPS JC70-10227A 1 ELA HOU-ENG B’D JC96-01350A 16 1 JC59-10507A 1 1 1 1 (110V) 1 FUSE-FERRULE 3601-000003 1 (220V) 2 FUSE-FERRULE 3601-000296 1 17 IPR-GROUND-ICU JC70-10006A 1 18 ELA HOU-CONTROL XEU (A4) JC96-01566A 1 (220V) 19 IPR-DUMMY_SRL(PLUS) JC70-00015A 1 20 IC-RAM MODULE 1105-001213 1 Samsung Electronics 6-3 Exploded Views and Parts List 6-3 Frame Exploded View 1 1-15-3 1-12 1-15 1-12-1 1-15-1 1-16 1-15-4 1-13 1-15-2 1-12-2 1-17 1-19 -5 1-18 1-14 1-19 -3 1-12-3 1-17-2 1-19 -4 1-17-1 1-19 -4 1-19 -2-1 1-17-3 1-19 -2-2 1-19 -2-3 1-19 -2-4 1-11-1 1-9 1-19 -2 1-11-3 1-20 1-19 1-11 1-11-2 1-11-1 1-10 1-1-5 1-32 1-39 1-26 1-19 -1 1-1-7 1-25 1-1-6 1-8 1-7 1-8-3 1-1 1-1-4 1-8-1 1-8-2 1-1-1 1-37 1-1-2 1-27 1-29 1-1-3 1-6 1-1-8 1-22 1-28 1-30 1-35-1 1-3 1-2 1-35-2 1-35 1-34-1 1-34-2 1-34-3 1-33 1-5-1 1-4 1-23 1-24 1-34 1-5-2 1-34-4 1-5 1-31-5 1-38 1-31 1-31-1 1-31-4 1-31-2 1-31-3 6-4 Samsung Electronics Exploded Views and Parts List 6-4 Frame Ass’y Parts List NO Seq 1 1 Ass’y Name Ass’y Code Frame Ass’y MEA RACK-FRAME SUB JC96-01446C 1 2 3 4 5 6 7 8 2 3 4 5 PBA MAIN-H/V,TERMINA PBA MAIN-H/V,TERMINA ELA HOU-THERMISTOR MEA RACK-ACTUATOR TR PMO-ACTUATOR FEED (12) CBF HARNESS-PTL LUG MEA RACK-PLT MP,DRV FAN-DC SWITCH MEA RACK-BRKT_EXIT ELA HOU-PTL CBF HARNESS-GND WIRE IPR-GROUND_EXIT MEA RACK-TR_HOLD L ROLLER-TRANSFER MEA RACK-TR HOLDER,R GEAR-TRANSFER(12) MEA RACK-HOU EXIT JC66-40949A JC97-01104A MEA RACK-EXIT ROLLER JC97-01098A 1 2 2.1 2 3 4 3 4 5 20 22 23 24 25 26 27 28 29 30 31 PMO-GUIDE-FUSER CBF-HARNESS PBA MAIN-CLN CBF-HARNESS LSU-HARNESS CBF HARNESSIPR-SHIELD_CAP WIRE IPR-GROUND_PLATE MOT IPR-SHIELD ICU MPR-FILM_EMI MEA RACK-TR GUIDE,12 ELA HOU-DEVELOPER,GU ELA HOU-DEVELOPER,GUID ELA HOU-SENSOR C/O MEA RACK-EMPTY_ACT IPR-GROUND_MP(R) PMO-GUIDE P/U,PATH ELA HOU-CLEANIG PLT CAP-GND WIRE Samsung Electronics JC66-40006A JC70-11075A JC66-40964A IPR-EARTH_TRANS(12) PMO-HOLDER_PTL PBA MAIN-PTL ASS’Y JC70-11023A JC72-41187A JC92-01050A SPRING-TR(12) IPR-SPRING_PLATE12 PMO-BUSING_TR12,L PMO-HOLDER TR(12),L JC61-70940A JC70-11050A JC72-41283A JC72-41285A SPRING-TR(12) PMO-BUSHING TR12(R) PMO-HOLDER TR,R(12) JC61-70940A JC72-41060A JC72-41062A PMO-HOU_EXIT(250) JC72-41114A PMO-ROLLER_EXIT,MAIN PMO-ROLLER_EXIT,FR PMO-HOLDER_EXIT SPRING-EXIT(12) GEAR-EXIT MEC-BEARING,EXIT MEC-ROLL_EXIT,FR/UP JC72-41081A JC72-41082A JC72-41080A JC61-70939A JC66-40209A JC75-10529A JC75-10957A JC70-11088A JC72-41361A JC96-01229A JC72-00011A Q’ty 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 2 1 1 1 1 1 1 IPR-GUIDE TRANSFER IPR-PLATE SAW PMO-HOLDER SAW PLATE MPR-SHEET,GUIDE TR CBF HARNESS-MOTOR JC70-10220A JC70-10232A JC72-40247A JC74-10907A JC39-40575A PMO-LEVER_OPEN SPRING-LEVER PMO-HOLDER_SENSOR SWITCH-MICRO JC72-41351A JC61-70974A JC72-41359A 3405-000125 SPRING-EMPTY PMO-ACTUATOR_EMPTY12 JC61-70965A JC72-41290A JC97-01207A 1 2 36 37 38 39 GEAR-EXIT/U ID IPR-BRACKET_EXIT GEAR-EXIT,IDLE(Z17) JC96-00290A JC96-00291A JC96-01353A 1 2 3 4 35 JC70-11089A JC66-40966A JC66-40967A JC72-40233A JC39-40009A JC92-01084A JC39-40513A JC39-40540A JG39-40179A JC70-10003A JC70-10013A JC70-10225A JC74-10908A JC97-01183A 1 2 3 4 5 32 33 34 IPR-PLATE MP GEAR-IDLE A,MP GEAR-IDLE B,MP JC75-10962A JC97-01071A 1 2 3 18 19 JC72-41287A JC72-41289A JC39-40546A JC70-11058A JC97-01079A 1 2 3 4 16 17 PMO-ACTUATOR TR PMO-HOLDER_ACTUATOR JC96-01150A 1 2 3 13 14 15 JC72-41113A JC72-41186A JC72-41350A JC70-11070A JC70-10911A JC70-11068A JC70-10980A JC72-41288A 3103-001062 JC39-00004A JC97-01198A 1 2 3 12 PMO-BASE FRAME(12) PMO-ROM COVER PMO-GUIDE_SKEW(12) IPR-GROUND_OPC(12) IPR-EARTH PLATE,FU IPR-GUIDE_DUST IPR-GND PLT G/TR(12) PMO-DAMPER_PLATE JC72-00012A JC39-40576A JC97-01229A 1 2 3 9 10 11 Sub Code JC92-00338A JC92-00339A JC96-01148A JC97-01208A 1 2 6 7 8 Part Name 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 6-5 Exploded Views and Parts List 6-5 Cover Ass’y Exploded View 3 3-1-10 3-1-9 3-1-8 3-1-7 3-1-6 3-1-19 3-1-5 3-1-20 3-1 3-1-22 3-1-21 3-1-23 3-1-20 3-1-19 3-1-15 3-1-18 3-1-24 3-1-18 3-1-25 3-1-26 3-1-27 3-1-24 3-1-1 3-1-3 3-1-2 3-1-4 3-1-16 3-1-12 3-1-17 3-1-14 3-1-13 3-3 3-1-11 3-2 6-6 Samsung Electronics Exploded Views and Parts List 6-6 Cover Ass’y Parts List NO Seq 3 Ass’y Name Ass’y Code Part Name Sub Code Q’ty Cover Main Ass’y 1 ELA HOU-CVR MAIN JC96-01477A 1 1 SPRING-COVER_OPEN,R JC61-70944A 1 2 SPRING-OPEN JC61-70975A 1 3 PMO-HSG_BUTTON C/O JC72-41366B 1 4 PMO-BUTTON C/O JC72-41367B 1 5 PMO-GUIDE_EXIT UP JC72-41369A 1 6 PMO-STACKER_EXIT A JC72-41371B 1 7 PMO-GUIDE_EXIT LR JC72-41374B 1 8 PMO-COVER_EXIT JC72-41370B 1 9 PMO-STACKER_EXIT B JC72-41372B 1 10 PMO-STACKER_EXIT C JC72-41373B 1 11 SPRING-ES 6107-000133 1 12 IPR-PLATE SPRING DEV JC70-10223A 2 PMO-LEVER_HOOK JC72-40325A 1 14 13 PMO-BUTTON_PANEL,LED JC72-41219A 1 15 PMO-STACKER SUB JC72-41220A 1 16 PMO-CVR_FRONT LED JC72-41368B 1 17 PMO-WINDOW_LED JC72-41397A 1 18 PMO-COVER_MAIN JC72-41365B 1 19 PMO-LOCKER_EXIT JC72-41395A 1 20 PMO-GUIDE_DUMMY JC72-41111A 2 21 RCT-PAD_DUMMY JC73-30912A 2 22 IPR-GROUND_ANTI JC70-11057A 1 23 MCT-BRUSH_ANTI JC74-40902A 1 24 PMO-HINGE HSG,R JC72-41216A 2 25 IPR-SHAFT COVER OPEN JC70-10228A 1 26 SPRING-COVER_OPEN,L JC61-70945A 1 27 PMO-LEVER EMPTY MP JC72-41353A 1 2 PMO-CAP_PANEL WIRE JC72-41375B 3 PBA BPA-PANEL,LED JC92-00346A Samsung Electronics 1 6-7 Exploded Views and Parts List 6-7 MP-Tray/MPF Exploded View 6-7-1 MP-Tray Exploded View 4-5 4-6 4 4-2 4-6 4-4 4-7 4-3 4-1 6-7-2 MPF Exploded View 5 5-24 5-26 5-23 5-16 5-20 5-26 5-2 5-27 5-22 5-16 5-27 5-13 5-18 5-19 5-11 5-17 5-16 5-6 5-15 5-14 5-21 5-5 5-4 5-12 5-3 5-8-3 5-8 5-8-2 5-8-4 5-8-1 5-9 5-7 5-10 5-1 6-8 Samsung Electronics Exploded Views and Parts List 6-8 MP-Tray/MPF Parts List 6-8-1 MP-Tray Parts List NO Seq 4 Ass’y Name MEA RACK-MP TRAY Ass’y Code Part Name Sub Code Q’ty JC97-01202D 1 1 PMO-COVER_MP JC72-41377D 1 2 PMO-TRAY_MP,A JC72-41378B 1 3 PMO-TRAY_MP,B JC72-41379B 1 4 PMO-TRAY_MP,C JC72-41380B 1 5 PMO-ADJUSTER_P SIDE JC72-41381B 1 6 PMO-LOCKER_MP JC72-41398A 2 7 IPR-GUIDE LATCH JB70-10906A 1 Samsung Electronics 6-9 Exploded Views and Parts List 6-8 MP-Tray/MPF Parts List 6-8-2 MPF Parts List NO Seq 5 6-10 Ass’y Name MEA RACK-MPF Ass’y Code Part Name Sub Code JC97-01201A Q’ty 1 1 PMO-FRAME_MP JC72-41352A 1 2 IPR-BRACKET_MP JC70-11080A 1 3 IPR-PLT KNOCK_UP,MP JC70-11081A 1 4 MPR-PAD_K/U,MP JC74-10911A 1 5 PMO-GUIDE_K/U,MP JC72-41354A 1 6 IPR-GUIDE_SIDE,MP JC70-11082A 1 7 PMO-ADJUSTER_END,MP JC72-41355A 1 8 MEC-HOLDER PAD ASS’Y JC75-00005A 1 1 PMO-HOLDER_P/U,MP JC72-41356A 1 2 PMO-HOLDER_PAD,MP JC72-41357A 1 3 RCT-PAD_P/U,MP JC73-30913A 1 4 IPR-GUIDE_P/U,MP JC70-11083A 1 9 SPRING-PICK UP,MP JC61-70973A 1 10 IPR-GROUND_MP JC70-11084A 1 11 ICT-SHAFT_P/U,MP JC70-40920A 1 12 PMO-GUIDE_LEFT,PATH JC72-41360A 1 13 PMO-ROLLER_IDLE,P/U JC72-41362A 1 14 PMO-HOUSING_P/U,MP JC72-41363A 1 15 RMO-RUBBER_P/U,MP JC73-40916A 1 16 PMO-BUSHING_P/U,MP JC72-41364A 2 17 GEAR-TRANS,MP JC66-40965A 1 18 PHOTO-INTERRUPTER 0604-001095 1 19 SPRING-KNOCKUP JC61-00001A 1 20 DAMPER JC72-00010A 1 21 SOLENOIDE JC33-00001A 1 22 CBF HARNESS MP SENSOR JC39-00003A 1 23 PMO-HOLDER-CAM,MPF JC72-00055A 1 24 PMO-GEAR-P/U,MPF JC72-00056A 1 25 PMO-CAM-PICKUP,MPF JC72-00057A 1 26 SPRING-CAM,MP JC61-00003A 1 27 WASHER-PLAIN 6031-000021 2 Samsung Electronics Exploded Views and Parts List 6-9 Motor-Main Exploded View 6 6-6 6-2 6-3 6-7 6-5 6-1 6-8 6-10 Samsung Electronics 6-9 6-11 6-4 6-11 Exploded Views and Parts List 6-10 Motor-Main Parts List NO Seq 6 6-12 Ass’y Name ELA-Hou- Motor Main Ass’y Code Part Name Sub Code Q’ty JC96-01099A 1 MOTOR-STEP 3101-001144 1 2 GEAR-125/18 JC66-40376A 1 3 IPR-BRKT_MOTOR JC70-10985A 1 4 GEAR-Z132/50(12) JC66-40959A 1 5 GEAR-IDLE FU JC66-40377A 1 6 GEAR-FUSER DRIVE JC66-40378A 1 7 IPR-BRKT_GEAR JC70-10984A 1 8 GEAR-IDLE OPC(12) JC66-40960A 1 9 GEAR-OPC DRIVE(12) JC66-40961A 1 10 GEAR-FEED DRV(12) JC66-40962A 1 11 GEAR-OPC DRV2 JC66-40910A 1 12 FILM-BRACKET JC73-00002A 1 Samsung Electronics Exploded Views and Parts List 6-11 Fuser Exploded View 8 8-2-4 8-2-6 8-2 8-2-12 8-2-3 8-2-27 8-2-2 8-2-5 8-2-8 8-2-11 8-2-9 8-2-7 8-2-10 8-2-14 8-2-1 8-2-16 8-1 8-2-21 8-2-25 8-2-15 8-2-18 8-2-20 8-2-26 8-2-17 8-2-22 8-2-24 8-2-13 8-2-19 8-2-23 Samsung Electronics 6-13 Exploded Views and Parts List 6-12 Fuser Ass’y Parts List NO Seq 8 Ass’y Code Part Name Sub Code Q’ty Fuser Ass’y 1 PMO-ACTUATOR_EXIT JC72-41079A 1 2 ELA HOU-FUSER(110V) JC96-01093A 1 (110V) ELA HOU-FUSER(220V) JC96-01094A 2 6-14 Ass’y Name 1 (220V) 1 LAMP-HALOGEN 4713-001076 1 (110V) 1 LAMP-HALOGEN 4713-001075 1 (220V) 2 SPRING-CLAW JC61-70922A 5 3 LABEL(R)-HOT FU JC68-30512A 1 4 NPR-ELECTRODE FUSER JC71-10902A 1 5 PMO-CLAW SEPARATOR JC72-41064A 5 6 THERMOSTAT 4712-000001 1 7 NPR-ELECTRODE FU R JC71-10201A 1 8 PMO-FUSER_UPPER JC72-41073A 1 9 PMO-ROLLER_EXIT F/UP JC72-40342A 4 10 IPR-SPRING_EXIT,PLT JC70-11067A 4 1 11 THERMISTOR-NTC 1404-001117 12 CBF HARNESS-FU(110V) JC39-40609A 1 (110V) 12 CBF HARNESS-FU(220V) JC39-40610A 1 (220V) 13 SPRING-PR JC61-70923A 2 14 BEARING-EXIT FU L JC66-10200A 1 15 BEARING-EXIT FU JC66-10201A 1 16 GEAR-EXIT JC66-40209A 1 17 GEAR-FUSER,Z32 JC66-40926A 1 18 IPR-FUSER_LOWER JC70-10983A 1 19 NEX-ROLLER_HEAT JC71-20901A 1 20 PMO-GUIDE_PATH JC72-41074A 1 21 PMO-FUSER_REAR JC72-41075A 1 22 PMO-BUSHING HR,L JC72-41076A 1 23 PMO-BUSHING HR,R JC72-41077A 1 24 PMO-BUSHING PR JC72-41078A 2 25 MEC-ROLL_EXIT,FU/LR JC75-10955A 1 26 MEC-ROLLER_PRESSURE JC75-10956A 1 27 GEAR-EXIT,IDLE(Z17) JC66-40964A 2 Samsung Electronics Exploded Views and Parts List 6-13 Pick-Up Exploded View 9 9-22 9-3 9-8 9-23 9-3 9-18 9-21 9-4 9-11 9-9 9-19 9-15 9-5 9-10 9-3 9-3 9-6 9-2 9-17 9-13 9-14 9-20 9-12 9-7 9-12 9-1 9-16 Samsung Electronics 9-7 6-15 Exploded Views and Parts List 6-14 Pick-Up Parts List NO Seq 9 6-16 Ass’y Name MEA RACK-FEEDER Ass’y Code Part Name Sub Code JC97-01078A Q’ty 1 1 SPRING-FEED(1) JC61-70941A 1 2 SPRING-FEED(2) JC61-70942A 1 3 BEARING-PICK UP JC66-10202A 4 4 GEAR-P/UP DRIVE JC66-40219A 1 5 GEAR-FEED JC66-40375A 1 6 IPR-SHAFT FEED JC70-10229A 1 7 IPR-SHAFT FEED IDLER JC70-10230A 1 8 IPR-SHAFT PICK UP JC70-10231A 1 9 IPR-GND_FEED JC70-10991A 1 10 IPR-GUIDE_FEED JC70-10992A 1 11 PMO-HOUSING P/UP JC72-40252A 1 12 PMO-ROLLER FEED L JC72-40261A 2 13 PMO-ROLLER FEED S JC72-40262A 1 14 PMO-SUB HOLDER FEED JC72-40266A 1 15 PMO-FRAME_FEED JC72-41115A 1 16 PMO-HOLDER FEED(1) JC72-41184A 1 17 PMO-HOLDER FEED(2) JC72-41185A 1 18 PMO-IDLE PICK_UP JC72-41234A 1 19 RMO-RUBBER PICK_UP JC73-40907A 1 20 PMO-ROLL_FEED,DRV 12 JC72-41295A 1 21 SPRING-PICKUP(12) JC61-70966A 1 22 GEAR-PICK UP(12) JC66-40958A 1 23 PMO-LEVER_PICKUP JC72-41339A 1 Samsung Electronics Exploded Views and Parts List 6-15 Cassette Exploded View 10 10-2 10-8 10-5 10-13 10-11 10-7 10-20 10-9 10-12 10-1 10-10 10-11 10-3 10-4 10-21 10-24 10-6 10-22 10-15 10-23 10-14 10-16 Samsung Electronics 10-18 10-17 10-19 6-17 Exploded Views and Parts List 6-16 Cassette Parts List NO Seq 10 6-18 Ass’y Name MEA RACK-CAST_X/A4 Ass’y Code Part Name Sub Code JC97-01261A Q’ty 1 1 SPRING-KNOCK UP(12) JC61-70951A 1 2 LABEL(R)-PLATE JC68-30929A 1 3 IPR-FINGER JC70-10213A 1 4 IPR-GUIDE PAPER JC70-10219A 2 5 IPR-PLT KNOCK UP(12) JC70-11022A 1 6 PMO-HOLDER FINGER JC72-41182A 1 7 PMO-LOCKER PLATE JC72-41210A 1 8 RPR-MMP PAD JC73-10911A 1 9 SPRING-LOCKER,PLATE JG61-70531A 1 10 LABEL(R)-HEIGHT JG68-30572A 1 11 IPR-TENSION_LETTER JC70-11085A 2 12 IPR-BRACKET_LEGAL JC70-11086A 1 13 IPR-BRACKET_LETTER JC70-11087A 1 14 PMO-FRAME_CASSETTE JC72-41382B 1 15 PMO-GUIDE_CASSETTE JC72-41383B 1 16 PMO-GUIDE_S CAST,P JC72-41384B 1 17 PMO-INDICATOR_EMPTY JC72-41385B 1 18 PMO-WINDOW_EMPTY JC72-41386A 1 19 PMO-HOLDER_INDICATOR JC72-41388A 1 20 PMO-GUIDE_LETTER JC72-41392A 1 21 PMO-GUIDE_LEGAL JC72-41393A 1 22 PMO-ADJUSTER_S CAST JC72-41394A 1 23 IPR-GUIDE_PLATE JC70-10993A 1 24 PMO-GUIDE REAR JC72-41180A 1 Samsung Electronics 23-25 Samsung Electronics 23-22 23-21 23-26 23-2 23-4 23-28 23-35 23-3 23-28-3 23-5 23-10 23-10 23-11 23-20 23-19 23-28-1 23-28-2 23-28-4 23-34 23-14 23-13 23-27 23-30 23-1 23-3 23-31 23-14 23-12 23-32 23-15 23-16 23-18 23-6 23-8 23-9 23-29-1 23-29-2 23-7 23-29-3 23-27 23-29-4 23-29 9-19 23-24 23-7 23-17 23-23 23-33 23 Exploded Views and Parts List 6-17 Second Cassette Frame Exploded View (option) 6-19 Exploded Views and Parts List 6-18 Second Cassette Frame Parts List (option) NO Seq 23 1 2 3 4 29 1 2 3 4 6-20 Ass’y Code Part Name Sub Code ELA HOU-SCF(ML6100) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 9 23 Ass’y Name 19 30 31 32 33 34 PBA MAIN-SCF MEC-ROLLER_INNER UPP BEARING-ROLLER IDLER GEAR-FEED PMO-GUIDE-INNER UP IPR-FRAME_RIGHT(SCF) IPR-BRKT_SUPPORT IPR-GROUND_ROLLER PMO-GUIDE_RAIL GEAR-IDLE 19 GEAR-IDLER OPTION IPR-FRAME_LEFT(SCF) PMO-GUIDE_RAIL FOOT-RUBBER IPR-FRAME_LOWER(12) PMO-STOPPER_SCF IPR-FRAME_UPPER PMO-ACTUATOR_ARM SOLENOID-MAGNET GEAR-DOUBLE OPTION MOTOR-STEP IPR-BRKT_MOTOR(SCF) PMO-COVER_REAR PMO-COVER_RIGHT.SCF/P PMO-COVER_LEFT.SCF/P IPR-SHIELD-PCB(SCF) PMO-BEARING_FEED ELA HOU-FEEDER CLUTC PMO-HUB_CLUTCH SPRING-TS, CLUTCH GEAR-P/UP OPTION PMO-COLLAR_CLUTCH_PI MEA RACK-FEEDER P/U ICT-SHAFT_PICK UP ICT-PIN_PARELLED,P/U PMO-HOLDER_HOUSING PMO-IDLE_SCF RMO-RUBBER PICK_UP CBF HARNESS-SCF CORE CBF HARNESSLABEL WARNING LABEL SCF CABLE CLAMP JC92-01077A JC75-10028B JC66-10304A JC66-40014A JC72-40307A JC70-10022A JC70-10461A JC70-10467A JC72-40371A JC66-40012A JC66-40365A JC70-10023A JC72-40371A JC61-40301A JC70-11065A JC72-41347A JC70-10027A JC72-40370A JC33-10001A JC66-40363A 3101-001158 JC70-10986A JC72-40362B JC72-41390B JC72-41389B JC70-10451A JC72-40531A JC96-00406B JC72-40587A JC61-70331A JC66-40364A JC72-40569B JC97-01212A JC70-40002A JC70-40360A JC72-40654A JC72-41348A JC73-40907A JC39-40541A JC39-40305B JC68-00059A 6502-000003 Q’ty 1 1 1 2 1 1 1 2 1 1 2 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Samsung Electronics Exploded Views and Parts List 6-19 Second Cassette Exploded View (option) 23-35 23-35-13 23-35-11 23-35-2 23-35-22 23-35-8 23-35-6 23-35-4 23-35-3 23-35-5 23-35-7 23-35-9 23-35-4 23-35-10 23-35-23 23-35-1 23-35-26 23-35-8 23-35-17 23-35-24 23-35-15 23-35-14 23-35-16 Samsung Electronics 23-35-20 23-35-25 23-35-19 23-35-21 6-21 Exploded Views and Parts List 6-20 Second Cassette Parts List (option) NO 23 6-22 Seq 35 Ass’y Name MEA RACK-CAST,SCF Ass’y Code Part Name Sub Code JC97-01240C Q’ty 1 1 SPRING-KNOCK UP(12) JC61-70951A 1 2 LABEL(R)-PLATE JC68-30929A 1 3 IPR-FINGER JC70-10213A 1 4 IPR-GUIDE PAPER JC70-10219A 1 5 IPR-GUIDE_SCF JC70-11076A 1 6 IPR-PLT KNOCK UP(12) JC70-11022A 1 7 PMO-LOCKER PLATE JC72-41210A 1 8 RPR-MMP PAD JC73-10911A 1 9 SPRING-LOCKER,PLATE JG61-70531A 1 10 LABEL(R)-HEIGHT JG68-30572A 1 11 IPR-TENSION_LETTER JC70-11085A 2 12 IPR-BRACKET_LEGAL JC70-11086A 1 13 IPR-BRACKET_LETTER JC70-11087A 1 14 PMO-FRAME_CASSETTE JC72-41382B 1 15 PMO-GUIDE-CST JC72-40306B 1 16 PMO-GUIDE 2’ND CAST JC72-41391B 1 17 PMO-ROLLER_EXIT JC72-40361A 2 18 SPRING-ES 6107-001047 2 19 PMO-INDICATOR_EMPTY JC72-41385A 1 20 PMO-WINDOW_EMPTY JC72-41386A 1 21 PMO-HOLDER_INDICATOR JC72-41388B 1 22 PMO-GUIDE_LETTER JC72-41392B 1 23 PMO-GUIDE_LEGAL JC72-41393B 1 24 PMO-ADJUSTER_S CAST JC72-41394A 1 25 IPR-GUIDE_PLATE JC70-10993A 1 26 PMO-GUIDE REAR JC72-41180B 1 Samsung Electronics SEC CODE JC96-01350A JC92-01083A 0201-000008 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0402-000012 0402-000104 0402-000129 0402-000129 0402-000351 0402-000468 0402-001193 0402-001193 0403-000227 0403-000346 0403-000356 0403-000475 0501-000010 0501-000010 0501-000010 0501-000294 0501-000294 0502-000245 0502-001124 0604-000001 0604-000146 0604-001033 0801-000528 0801-000722 0803-000679 0803-001097 0903-000219 1103-001045 1201-000229 1202-000103 1203-000531 1404-000167 1405-000125 2001-000003 2001-000003 2001-000003 2001-000005 2001-000010 2001-000012 2001-000015 2001-000016 2001-000019 2001-000023 2001-000027 2001-000045 2001-000085 2001-000105 2001-000118 2001-000221 2001-000273 2001-000281 2001-000281 2001-000281 2001-000281 2001-000294 2001-000319 DESCRIPTION ELA HOU-ENG B'D,XRX PBA MAIN-ENGINE ADHESIVE-HM DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-BRIDGE DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-POWER TR-POWER PHOTO-COUPLER PHOTO-COUPLER PHOTO-INTERRUPTER IC-CMOS LOGIC IC-CMOS LOGIC IC-TTL IC-TTL IC-MICROCOMPUTER IC-EEPROM IC-OP AMP IC-VOLTAGE COMP. IC-SWITCH VOL. REG. THERMISTOR-NTC VARISTOR R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON SPEC LOCATION ML-6100,XEROX,USA,-,-,-,ML-6100,SEC,-,110V,-,-,PP_#3748,WHT,6500CPS,1N4148,100V,200MA,DO-35,TP 1N4148,100V,200MA,DO-35,TP 1N4148,100V,200MA,DO-35,TP 1N4148,100V,200MA,DO-35,TP 1N4148,100V,200MA,DO-35,TP 1N4148,100V,200MA,DO-35,TP 1N4148,100V,200MA,DO-35,TP 1N4148,100V,200MA,DO-35,TP 1N4148,100V,200MA,DO-35,TP UF4007,1KV,1A,DO-41,TP D3SBA60,600V,4A,-,ST 1N4003,200V,1A,DO-41,TP 1N4003,200V,1A,DO-41,TP 1N4937,600V,1A,DO-41,TP ESJS58-06,6KV,2mA,DO-201 SHV-04,4KV,20mA,-,TP SHV-04,4KV,20mA,-,TP 1N751A,5.1V,5%,500mW,DO-35,TP UZ33B,33V,30-36V,500mW,DO-35,T UZ5.6BCB,5.6V,5.46-5.7V,500mW, 1N5274B,130V,5%,500mW,DO-35,TP KSC1008,NPN,800mW,TO-92,TP,120 KSC1008,NPN,800mW,TO-92,TP,120 KSC1008,NPN,800mW,TO-92,TP,120 KSA708-Y,PNP,800mW,TO-92,TP,12 KSA708-Y,PNP,800mW,TO-92,TP,12 KSB1151-Y,PNP,1.3W,TO-126,-,16 KSD526,NPN,30W,TO-220,BK,120-2 TR,50-60%,200mW,DIP-4,ST TRIAC,-,250mW,DIP-6,ST TR,-,150mW,DIP-4,ST 74HCT574,D FLIP-FLOP,DIP,20P,3 74HC245,TRANSCEIVER,DIP,20P,30 7406,BUFFER/DRIVER,DIP,14P,300 7407,BUFFER/DRIVER,DIP,14P,300 88C4316,8BIT,DIP,64P,-,8MHz,ST 27E512,64Kx8BIT,DIP,28P,600MIL 324,DIP,14P,300MIL,QUAD,100V/m 393,DIP,8P,300MIL,DUAL,36V,CMO 5311,DIP,8P,300MIL,PLASTIC,-,3 5ohm,10%,3150K,18.7mW/C,TP 220V,4500A,17x4.2mm,TP 330ohm,5%,1/8W,AA,TP,1.8x3.2mm 330ohm,5%,1/8W,AA,TP,1.8x3.2mm 330ohm,5%,1/8W,AA,TP,1.8x3.2mm 390ohm,5%,1/8W,AA,TP,1.8x3.2mm 68KOHM,5%,1/8W,AA,TP,1.8X3.2MM 680KOHM,5%,1/8W,AA,TP,1.8X3.2MM 0.5OHM,5%,1/2W,AA,TP,2.4X6.4MM 1OHM,5%,1/2W,AA,TP,2.4X6.4MM 10OHM,5%,1/2W,AA,TP,2.4X6.4MM 47OHM,5%,1/4W,AA,TP,2.4X6.4MM 100OHM,5%,1/4W,AA,TP,2.4X6.4MM 1.8KOHM,5%,1/4W,AA,TP,2.4X6.4MM 100KOHM,5%,1/2W,AA,TP,2.4X6.4MM 1.5KOHM,5%,1/4W,AA,TP,2.4X6.4MM 180OHM,5%,1/2W,AA,TP,2.4X6.4MM 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10MOHM,5%,1/4W,AA,TP,2.4X6.4MM 120KOHM,5%,1/8W,AA,TP,1.8X3.2MM Page 1 D154,D209 D215,D220 D221,D222,D223,D224 D225,D226,D227,D228 D229,D230,D231,D232 D233,D401 D4,D5,D6,D7,D101 D500,D501,D502 D504,D505 D102 DB101 D1,D216,D217 D503 D103 D205,D206,D207,D208 D201,D202,D203,D204 D210 ZD102 ZD152,ZD204,ZD205 ZD151,ZD201 ZD203 Q211 Q3,Q4,Q8,Q10,Q208 Q500,Q503 Q207,Q209 Q501,Q502 Q9 Q201,Q202,Q203,Q204 PC152,PC153 PC151 OP1,OP2,OP3,OP4 U4 U6 U205 U203 U3 U2 U201 U5 U101 TH101 TNR101 JP122 R25,R52,R111,R151 R406 R221,R231 R240 R236 R62 R8 R217,R230 R109 R104 R274 R106,R107 R14 R103 R39 R238 R15,R24,R29,R30,R31 R155,R252,R282,R283 R284,R285,R293,R422 R514 R205 R215 Q'TY 1 1 0.005 2 2 4 4 4 2 5 3 2 1 1 3 1 1 4 4 1 1 3 2 1 1 5 2 2 2 1 4 2 1 4 1 1 1 1 1 1 1 1 1 1 1 1 4 1 2 1 1 1 1 2 1 1 1 2 1 1 1 1 5 4 4 1 1 1 2001-000331 2001-000362 2001-000362 2001-000429 2001-000429 2001-000429 2001-000429 2001-000435 2001-000449 2001-000449 2001-000515 2001-000552 2001-000563 2001-000565 2001-000577 2001-000660 2001-000660 2001-000660 2001-000734 2001-000734 2001-000761 2001-000780 2001-000786 2001-000812 2001-000812 2001-000812 2001-000812 2001-000816 2001-000832 2001-000864 2001-001015 2001-001070 2001-001093 2001-001150 2001-001165 2003-000703 2003-000706 2004-000002 2004-000003 2004-000345 2004-000345 2004-000345 2004-000385 2004-000433 2004-000544 2004-000691 2004-000699 2004-000754 2004-000869 2004-000884 2004-000900 2004-000965 2004-001156 2004-001231 2004-001231 2004-001315 2004-001315 2004-001357 2004-001357 2004-002001 2004-004179 2005-000164 2009-001041 2009-001042 2009-001082 2009-001083 2009-001084 2009-001085 2103-000156 2103-000270 2103-001079 R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON(S) R-METAL OXIDE(S) R-METAL OXIDE(S) R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-METAL R-WIRE WOUND,NON R-METAL GLAZE R-METAL GLAZE R-METAL GLAZE R-METAL GLAZE R-METAL GLAZE R-METAL GLAZE VR-SEMI VR-SEMI VR-SEMI 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM 150OHM,5%,1/8W,AA,TP,1.8X3.2MM 150OHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 220OHM,5%,1/8W,AA,TP,1.8X3.2MM 270OHM,5%,1/4W,AA,TP,2.4X6.4MM 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM 27OHM,5%,1/2W,AA,TP,3.3X9MM 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 430OHM,5%,1/8W,AA,TP,1.8X3.2MM 470OHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6OHM,5%,1/4W,AA,TP,2.4X6.4MM 510OHM,5%,1/8W,AA,TP,1.8X3.2MM 56KOHM,5%,1/8W,AA,TP,1.8X3.2MM 9.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 120OHM,5%,1/2W,AA,TP,2.4X6.4MM 2.2KOHM,5%,1/2W,AA,TP,2.4X6.4MM 470KOHM,5%,1/2W,AA,TP,2.4X6.4MM 56OHM,5%,1/2W,AA,TP,2.4X6.4MM 470ohm,5%,3W,AA,TP,6x16mm 47Kohm,5%,2W,AA,TP,4.3x12mm 78.7Kohm,1%,1/8W,AA,TP,1.8x3.2 16.2Kohm,1%,1/8W,AA,TP,1.8x3.2 15Kohm,1%,1/8W,AA,TP,1.8x3.2mm 15Kohm,1%,1/8W,AA,TP,1.8x3.2mm 15Kohm,1%,1/8W,AA,TP,1.8x3.2mm 17.4Kohm,1%,1/8W,AA,TP,1.8x3.2 1Kohm,1%,1/8W,AA,TP,1.8x3.2mm 21.5Kohm,1%,1/8W,AA,TP,1.8x3.2 3.16Kohm,1%,1/8W,AA,TP,1.8x3.2 3.3Kohm,1%,1/8W,AA,TP,1.8x3.2m 309Kohm,1%,1/8W,AA,TP,1.8x3.2m 3Kohm,1%,1/8W,AA,TP,1.8x3.2mm 4.3Kohm,1%,1/8W,AA,TP,1.8x3.2m 4.7Kohm,1%,1/8W,AA,TP,1.8x3.2m 470Kohm,1%,1/8W,AA,TP,1.8x3.2m 619Kohm,1%,1/8W,AA,TP,1.8x3.2m 75Kohm,1%,1/8W,AA,TP,1.8x3.2mm 75Kohm,1%,1/8W,AA,TP,1.8x3.2mm 86.6Kohm,1%,1/8W,AA,TP,1.8x3.2 86.6Kohm,1%,1/8W,AA,TP,1.8x3.2 93.1Kohm,1%,1/8W,AA,TP,1.8x3.2 93.1Kohm,1%,1/8W,AA,TP,1.8x3.2 12.1Kohm,1%,1/8W,AA,TP,1.8x3.2 174Kohm,1%,1/8W,AA,TP,1.8x3.2mm 0.1ohm,5%,2W,AA,BK,4x12mm 2Mohm,1%,1/4W,AA,TP,3X9mm 4.7Mohm,1%,1/4W,AA,TP,3x9mm 30Mohm,2%,2W,-,BK,30x8.5mm 200Mohm,2%,1/2W,CM,BK,18x6mm 30Mohm,2%,0.5W,CM,BK,18x6mm 10Mohm,3%,1/2W,CM,BK,18x4mm 10Kohm,10%,1/2W,TOP 20Kohm,10%,1/2W,TOP 100Kohm,15%,1/2W,TOP Page 2 R56,R63 R16,R23,R64 R512 R18,R33,R34 R408 R41,R42,R44,R45,R46 R49 R502 R48,R225,R250,R256 R501,R504 R27,R424,R425,R426 R112 R253 R517 R152 R249 R257,R263,R266 R500,R503,R507 R110 R251 R218 R156 R54,R223,R224,R227 R19,R26,R28,R35,R36 R261,R405 R38,R40,R51,R59 R60,R61,R260 R113 R20,R407 R53,R248 R262 R102 R292 R101,R105 R216,R219 R157,R158 R108 R247 R237 R17,R22,R55,R222 R43 R513 R510,R268 R58,R213 R508 R153 R516,R57 R511 R154 R37 R47 R243 R509 R269 R506 R234 R505 R233 R515 R245 R258 R114 R208,R209 R204,R207,R277 R280 R220 R211 R201 VR201,VR202,VR204 VR203 VR205 2 3 1 3 1 5 1 1 4 2 4 1 1 1 1 1 3 3 1 1 1 1 4 5 2 4 3 1 2 2 1 1 1 2 2 2 1 1 1 4 1 1 2 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 3 1 1 1 1 3 1 1 2201-000003 2201-000004 2201-000004 2201-000017 2201-000017 2201-000017 2201-000019 2201-000023 2201-000119 2201-000119 2201-000119 2201-000138 2201-000326 2201-000326 2201-000326 2201-000391 2201-000473 2201-000473 2201-000645 2201-000724 2201-000724 2201-002066 2201-002067 2202-000002 2202-000002 2202-000654 2301-000490 2305-000002 2306-000212 2401-000183 2401-000207 2401-002075 2401-003203 2801-000002 2902-001011 2902-001011 3301-000344 3601-000151 3601-000157 3602-000001 3704-000235 3711-000164 3711-000217 3711-000236 3711-000633 3711-000782 3711-000865 3711-001108 3711-002410 3711-002653 3711-003204 3711-003205 3711-003969 JC26-20301B JC26-20301C JC26-30506A JC27-40502A JC27-60101B JC27-60101C JC27-60502A JC27-60503A JC33-10501B JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL C-CERAMIC,MLC-AXIAL C-CERAMIC,MLC-RADIAL C-FILM,PEF C-FILM,MPEF C-FILM,MPPF C-AL C-AL C-AL C-AL CRYSTAL-UNIT FILTER-LINE FILTER-LINE CORE-FERRITE BEAD FUSE-FERRULE FUSE-FERRULE FUSE-CLIP SOCKET-IC CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER TRANS AFTRANS AFTRANS POWER-THV COIL CHOCK-68UH COIL FILTERCOIL FILTERCOIL FILTER-LINE110V COIL FILTER-3MH SOLENOID-6000 CBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESS- 68pF,10%,2KV,SL,TP,8x5,5 100pF,10%,2KV,SL,TP,8x5,5 100pF,10%,2KV,SL,TP,8x5,5 1nF,10%,50V,Y5P,TP,4x3.5,5 1nF,10%,50V,Y5P,TP,4x3.5,5 1nF,10%,50V,Y5P,TP,4x3.5,5 10nF,+80-20%,500V,Y5V,TP,13.5x 2.2nF,20%,125V,Y5U,TP,11x7,5 100nF,+80-20%,50V,Y5V,TP,8x3.5 100nF,+80-20%,50V,Y5V,TP,8x3.5 100nF,+80-20%,50V,Y5V,TP,8x3.5 100pF,10%,50V,Y5P,TP,4.0X4.0,2 2.2nF,10%,50V,Y5P,TP,6.5x3,5 2.2nF,10%,50V,Y5P,TP,6.5x3,5 2.2nF,10%,50V,Y5P,TP,6.5x3,5 22pF,5%,50V,SL,TP,5.0x3.0,5 33nF,+80-20%,50V,Y5V,TP,6x3,5 33nF,+80-20%,50V,Y5V,TP,6x3,5 680pF,5%,50V,SL,TP,10*3,5 470pF,0.1,3KV,Y5P,TP,8x5,5 470pF,0.1,3KV,Y5P,TP,8x5,5 470pF,10%,6KV,Y5P,TP,10x7,10 100pF,10%,6KV,Y5P,TP,8x7,10 10nF,0.05,500V,X7R,TP,5.1x6.4x 10nF,0.05,500V,X7R,TP,5.1x6.4x 100nF,10%,50V,X7R,TP,5.1x6.6,5 4.7nF,5%,100V,TP,5.8x3.1x12.5, 47NF,20%,275V,TP,18X12.5X5.5MM,15 470NF,20%,275V,BK,-,22.5 1000uF,20%,35V,WT,TP,12.5x25,5 100uF,20%,50V,WT,TP,8x12,5 4.7uF,20%,50V,GP,TP,5x11,5 470uF,20%,200V,GP,BK,30X25,10m 6.94407MHz,50ppm,28-AAM,20pF,5 -,-,-,-,ZZ,3.5x6.5mm,-,125V,5A,FA,GLASS,5X20MM 125V,8A,SB,GLASS,5X20MM -,-,30mohm 28P,DIP,SN,2.54mm 1WALL,2P,1R,2.5mm,STRAIGHT,SN 1WALL,3P,1R,3.96mm,STRAIGHT,SN 1WALL,4P,1R,3.96mm,STRAIGHT,SN BOX,11P,1R,2mm,STRAIGHT,SN BOX,2P,1R,2.0mm,STRAIGHT,SN BOX,3P,1R,2mm,STRAIGHT,SN BOX,8P,1R,2mm,STRAIGHT,SN BOX,10P,2R,2mm,STRAIGHT,SN BOX,3P,1R,2.5mm,STRAIGHT,SN BOX,24P,2R,2mm,STRAIGHT,SN BOX,4P,1R,2.0mm,STRAIGHT,SN BOX,2P,1R,2.5mm,STRAIGHT,SN ML-80,-,95MH ML-80,-,0.4WIRE ML-7000,-,57.5/1.3uH,180mH ML5500,68uH,0.04ohm,32T -,9UH,-,-,6UH,-,ML5500,7.0mH,0.10ohm,26T ML5500,3.0mH,0.40ohm,30T ML-6000,24VDC,72W,57,39X39X22, ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER Page 3 C203 C220 C404 C17,C22,C27,C29 C31,C38,C39,C40,C41 C42,C43,C45,C237 C106,C501 C103,C104,C115 C209 C222,C226,C227,C229 C26,C32,C34,C37,C46 C16,C28,C30,C402 C221,C223,C225 C230 C500 C20,C21 C207,C208,C210,C214 C224 C111 C201,C204,C219 C202,C206 C211,C212,C215,C216 C213 C10,C12,C15,C18,C401 C502 C110,C112 C113,C505 C102 C101 C156,C157 C228,C503,C504,C506 C33,C35 C107 X1 BD1,BD101,BD102 BD103,BD151,BD152 FB1,FB2,FB3,FB4,FB5 F151 F101 FH1,FH2,FH3,FH4 U2 CN4 CN101 CN12 CN3 CN105 CN103 CN6 CN104 CN7 CN5 CN2 CN8,CN10 T201,T202,T204 T101 T203 L103 L152 L151 L101 L102 JP104,JP105,JP106,JP107,JP108,JP109 JP110,JP111,JP112,JP113,JP114,JP115 JP116,JP117,JP118,JP119,JP120 JP121,JP123,JP124,JP125,JP126 JP127,JP128,JP129,JP130,JP131,JP132 JP133,JP134,JP135,JP136,JP137,JP138 JP139,JP140,JP141,JP142,JP142,JP143 JP144,JP145,JP146,JP147,JP148 JP149,JP150,JP151,JP152,JP153,JP154 1 1 1 4 5 4 2 3 1 4 5 4 3 1 1 2 4 1 1 3 2 4 1 5 1 2 2 1 1 2 4 2 1 1 3 3 5 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 2 3 1 1 1 1 1 1 1 1 6 6 5 5 6 6 6 5 6 JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC41-10529A JC70-10909A JC96-00320A 0402-000304 0402-000314 0502-001124 0505-000134 1401-000108 6003-000008 6003-000119 JC61-70100A JC62-20001A JC62-30001A JC62-30002A JF62-30201A JF68-30527H CBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSPCB-ENGINE IPR-CONNECTOR HV ELA HOU-H/SINK DIODE-RECTIFIER DIODE-RECTIFIER TR-POWER FET-SILICON THYRISTOR-TRIAC SCREW-TAPTITE SCREW-TAPTITE SPRING-PS TUBE-IRF840 HEAT SINK-TRANS HEAT SINK-SMPS HEAT SINK LABEL(R)-BAR CODE ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-80,JUMPER,AWG22,52mm,SILVER ML-5500,FR-1,1L,T1.6,247X299mm ML-80,AL,T0.8,ML-80(SEAU),-,EUROPE,-,-,-,STPR1020CF,200V,5A,TO-220,ST D10SC4M,40V,10A,ITO-220 KSD526,NPN,30W,TO-220,BK,120-2 IRF840,N,500V,8A,0.85OHM,125W,TO-220AB 100A,600V,-,5V/uS,TO-220AB BH,+,S,M3,L4,ZPC3,SWRCH18A BH,+,B,M3,L8,CBLACK,SWRCH18A ML-66G,STS304-W1/2H,T0.5,-,-,SSP5N90,IRF840,-,T0.45,L23,ML-80,AL,ML-80,AL,HVPS,SPCC,t1.0 SF1000,PY,38X6.5,T0.1,WHT JF68-30527N LABEL(R)-BAR CODE SF500,PY,20X10,T0.1,WHT JP155,JP156,JP157,JP158,JP159,JP160 JP16,JP17,JP21,JP22,JP23 JP161,JP162,JP163,JP164,JP165,JP166 JP167,JP168,JP169,JP170,JP171,JP172 JP173,JP174,JP175,JP176,JP177 JP178,JP179,JP180,JP181,JP182 JP188,JP189,JP190,JP191,JP192 JP193,JP194,JP195,JP196,JP197,JP198 JP199,JP200,JP203,JP187,JP268 JP204,JP205,JP206,JP208 JP209,JP210,JP211,JP212,JP213,JP214 JP217,JP218,JP219,JP220,JP221,JP222 JP223,JP224,JP225,JP226,JP227,JP228 JP229,JP230,JP231,JP232,JP233,JP234 JP25,JP26,JP27,JP28,JP29,JP30,JP31,JP216 JP272,JP273,JP274,JP275,JP276,JP601 JP33,JP34,JP35,JP36,JP37,JP38,JP39 JP40,JP41,JP42,JP43,JP44,JP45,JP46,JP47 JP49,JP50,JP51,JP52 JP55,JP56,JP57,JP58,JP59,JP60,JP62,JP63 JP602,JP605,JP616,JP7 JP617,R412 JP65,JP66,JP67,JP68,JP69,JP70,JP71,JP72 JP73,JP74,JP75,JP76,JP77,JP78,JP79,JP80 JP8,JP10,JP11,JP13 JP81,JP82,JP83,JP84,JP85,JP86,JP87,JP88 JP89,JP90,JP91,JP92,JP93,JP94,JP95,JP96 JP97,JP98,JP99,JP100,JP101,JP102,JP103 JS3,JS4,JS5,JP4,JP5,JP6 HP1,HP2,HP3,HP4 D153 D152 Q201,Q203 Q102 Q101 Q201,Q101 D152,D153,Q203 FOR SMPS H/SINK Q102 Q102,D152.D153 Q203 Q101,Q201 6 5 6 6 5 5 5 6 5 4 6 6 6 6 8 6 7 8 4 8 4 2 8 8 4 8 8 7 6 1 4 1 1 1 2 1 1 2 3 1 1 1 1 2 1 1 Page 4 Network Card Parts List 07-5. Network Card Parts List Lev SEC Code 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 6001-000131 JC69-00045A JC69-30906A JC70-00021A JC92-01119A 0601-000105 0601-000105 0801-001072 0903-001118 1103-001061 1105-001252 1106-001275 1106-001275 1107-001046 1205-001675 2007-000023 2007-000023 2007-000026 2007-000026 2007-000026 2007-000026 2007-000029 2007-000029 2007-000029 2007-000029 2007-000029 2007-000029 2007-000029 2007-000238 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000297 2007-000449 2007-000468 2007-000468 2007-000468 2007-000468 2007-000468 2007-000468 2007-000511 2007-000766 2007-000766 2007-000766 2007-000766 2007-000766 2007-000781 2007-000781 2007-000781 2007-000781 2007-000781 2007-000781 2007-000953 2007-000953 2007-001067 2007-001092 2007-001092 2007-001133 2007-001133 2007-002826 2011-001094 2011-001094 2203-000192 2203-000192 2203-000192 Location NO. PBA ASSY LED1 LED2 U20 U26 U15 U18 U24 U25 U19 U165 R79 R80 R68 R69 R70 R71 L1 L2 R30 R72 R73 R97 R98 R148 R118 R119 R120 R121 R124 R126 R127 R128 R129 R147 R150 R92 R94 R95 R96 R105 R74 R75 R76 R78 R87 R88 R111 R125 R146 R89 R90 R91 R104 R123 R138 R144 R145 R149 R108 R109 R110 R106 R107 R103 R113 R112 RA1 RA10 C100 C101 C102 Samsung Electronics Q’ty 2 0.2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Description/Specification A/S SCREW-MACHINE “BH,+,M3,L6,ZPC(YEL),SM20C,-” “BOX-MASTER NET,NEC” “NEC,ML-7000,SW-1,284*210*190,-” BAG-NETWORK “SHIELDING,T1,250*160,ML-7000” CAP-BRKT NET OPT “ML-7000,SPCC,T0.8,-” PBA SUB-NPC(NEC) “ML-7000N3/NEC,NEC,USA,100BASE NETWORK CARD,-,-,-” LED “CBI-ANGLE,GRN,5mm,560nm” LED “CBI-ANGLE,GRN,5mm,560nm” IC-CMOS LOGIC “74ACT32,OR GATE,SOP,14P,150MIL” IC-MICROCONTROLLER “32C5000,32BIT,QFP,208P,-,33MHz” IC-EEPROM “24C32,4Kx8BIT,SOP,8P,150MIL,10” IC-DRAM “416C4100,4MX16BIT,TSOP,50P,400MIL,45NS,5V,10%,PLASTIC,0TO+70C,” IC-SRAM “68257,32KX8BIT,TSOP,28P,300MIL,15NS,5V,10%,PLASTIC,0TO+70C,2MA” IC-SRAM “68257,32KX8BIT,TSOP,28P,300MIL,15NS,5V,10%,PLASTIC,0TO+70C,2MA” IC-FLASH MEMORY “29F800,512Kx16BIT,TSOP,48P,724” IC-TRANSCEIVER “ICS1892Y,MQFP,64P,551MIL,PLASTIC,5V,-,-5TO+85C,TR,-” R-CHIP “120OHM,5%,1/10W,DA,TP,2012” R-CHIP “120OHM,5%,1/10W,DA,TP,2012” R-CHIP “200OHM,5%,1/10W,DA,TP,2012” R-CHIP “200OHM,5%,1/10W,DA,TP,2012” R-CHIP “200OHM,5%,1/10W,DA,TP,2012” R-CHIP “200OHM,5%,1/10W,DA,TP,2012” R-CHIP “0OHM,5%,1/10W,DA,TP,2012” R-CHIP “0OHM,5%,1/10W,DA,TP,2012” R-CHIP “0OHM,5%,1/10W,DA,TP,2012” R-CHIP “0OHM,5%,1/10W,DA,TP,2012” R-CHIP “0OHM,5%,1/10W,DA,TP,2012” R-CHIP “0OHM,5%,1/10W,DA,TP,2012” R-CHIP “0OHM,5%,1/10W,DA,TP,2012” R-CHIP “1.5KOHM,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “10Kohm,1%,1/10W,DA,TP,2012” R-CHIP “180OHM,5%,1/10W,DA,TP,2012” R-CHIP “1KOHM,5%,1/10W,DA,TP,2012” R-CHIP “1KOHM,5%,1/10W,DA,TP,2012” R-CHIP “1KOHM,5%,1/10W,DA,TP,2012” R-CHIP “1KOHM,5%,1/10W,DA,TP,2012” R-CHIP “1KOHM,5%,1/10W,DA,TP,2012” R-CHIP “1KOHM,5%,1/10W,DA,TP,2012” R-CHIP “2.4KOHM,5%,1/10W,DA,TP,2012” R-CHIP “330OHM,5%,1/10W,DA,TP,2012” R-CHIP “330OHM,5%,1/10W,DA,TP,2012” R-CHIP “330OHM,5%,1/10W,DA,TP,2012” R-CHIP “330OHM,5%,1/10W,DA,TP,2012” R-CHIP “330OHM,5%,1/10W,DA,TP,2012” R-CHIP “33OHM,5%,1/10W,DA,TP,2012” R-CHIP “33OHM,5%,1/10W,DA,TP,2012” R-CHIP “33OHM,5%,1/10W,DA,TP,2012” R-CHIP “33OHM,5%,1/10W,DA,TP,2012” R-CHIP “33OHM,5%,1/10W,DA,TP,2012” R-CHIP “33OHM,5%,1/10W,DA,TP,2012” R-CHIP “49.9OHM,1%,1/10W,DA,TP,2012” R-CHIP “49.9OHM,1%,1/10W,DA,TP,2012” R-CHIP “6.8KOHM,1%,1/10W,DA,TP,2012” R-CHIP “620OHM,5%,1/10W,DA,TP,2012” R-CHIP “620OHM,5%,1/10W,DA,TP,2012” R-CHIP “68OHM,5%,1/10W,DA,TP,2012” R-CHIP “68OHM,5%,1/10W,DA,TP,2012” R-CHIP “110OHM,1%,1/10W,DA,TP,2012” R-NETWORK “39ohm,5%,1/16W,L,CHIP,8P,TP” R-NETWORK “39ohm,5%,1/16W,L,CHIP,8P,TP” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” 7-9 Network Card Parts List Network Card Parts List Lev SEC Code 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000316 2203-001002 2203-001002 2203-001002 2404-000128 2404-000128 2404-000128 2804-001056 2804-001311 3301-000344 3702-001102 3711-003205 3722-001319 JC13-00004A JC41-00011A JK68-10100A 7-10 Location NO. C103 C104 C105 C106 C107 C108 C109 C110 C127 C128 C129 C130 C131 C132 C133 C134 C135 C136 C137 C138 C139 C140 C141 C142 C143 C144 C145 C146 C147 C148 C149 C150 C151 C152 C153 C154 C158 C159 C160 C161 C162 C163 C169 C170 C88 C90 C94 C95 C96 C97 C185 C182 C183 C184 C186 C91 C92 Y1 Y2 BD2 J1 CN6 CN5 U22 PCB - Q’ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Description/Specification “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-CERAMIC,CHIP” “C-TA,CHIP” “C-TA,CHIP” “C-TA,CHIP” OSCILLATOR-CLOCK OSCILLATOR-CLOCK CORE-FERRITE BEAD CONNECTOR-RIBBON CONNECTOR-HEADER JACK-MODULAR IC-ASIC-NPC PCB—NPC2 LABEL(P)-BLANK Svc. “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “100nF,+80-20%,50V,Y5V,TP,2012,” “120pF,5%,50V,NPO,TP,2012,-” “.047NF,5%,50V,NPO,TP,2012” “.047NF,5%,50V,NPO,TP,2012” “.047NF,5%,50V,NPO,TP,2012” “10uF,20%,16V,-,TP,6032,-” “10uF,20%,16V,-,TP,6032,-” “10uF,20%,16V,-,TP,6032,-” “33MHz,100ppm,10TTL,-,5V,30mA” “25MHZ,50PPM,CMOS,ST,5V,30MA” “ZZ,3.5x6.5mm,-,-” “60P,FEMALE,STRAIGHT,AU” “BOX,4P,1R,2.0mm,STRAIGHT,SN” “8P/8C,-,AU30U,BLK,NO” “ML-7000N3,NETBRIDGE,TQFP,160,945MIL” “ML-7000N3,FR-4,4 LAYER,1.6T,1.6T*124*80” “ER-4615(SESAB),ART,W70*L30,120” Samsung Electronics Electrical Parts List 07-Electrical Parts List 07-1 Controller Board Lev SEC Code 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0407-000101 0801-001072 0803-000117 0803-000207 0803-000270 0803-000303 0803-000468 0803-001381 0803-003058 0904-001319 1006-000243 1103-000133 1105-001213 1107-001121 1203-000346 1203-001026 2007-000028 2007-000029 2007-000029 2007-000029 2007-000241 2007-000290 2007-000290 2007-000300 2007-000300 2007-000300 2007-000300 2007-000300 2007-000300 2007-000300 2007-000300 2007-000300 2007-000300 2007-000300 2007-000300 2007-000300 2007-000300 2007-000308 2007-000312 2007-000449 2007-000468 2007-000468 2007-000468 2007-000468 2007-000477 2007-000493 2007-000551 2007-000671 2007-000686 2007-000781 2007-000781 2007-000781 2007-000781 2007-000781 2007-000931 2007-000964 2007-001133 2011-001093 2011-001094 2011-001094 2011-001094 2011-001094 2011-001094 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 Location NO. “D2,D3” “U3,U5,U12” “U15,U28” U4 U9 U19 U23 U16 U21 U7 U17 U26 “U1,U2” “U8,U11” U20 “U25,U27” R201 “R21,R27,R58,R70,R71” “R7,R17,R20” “R75,R77,R82,R199” R52 “R101,R29” “R33,R36,R38,R39,R79,R98” “R113,R114,R123,R133,R134,R135” “R136,R137,R139,R140,R141,R142” “R143,R144,R145,R146,R147,R148” “R150,R151,R152,R153,R155,R157” “R166,R168,R169,R170,R171,R172” “R173,R175,R177,R182” R190 “R191,R192,R193,R194,R195,R198” “R37,R40,R42,R65,R66,R45” “R46,R47,R49,R67,R181,R53” “R60,R69,R106,R72,R76,R78” “R8,R18,R23,R34,R64,R35” “R80,R84,R91,R93,R94” “R95,R96,R97,R100,R103” “R54,R63,R68,R89,R154,R9” R167 R90 “R110,R117,R118,R119,R120,R121” “R161,R163,R165,R179,R180” “R24,R81,R87,R107,R108,R109” “R28,R48,R86” R200 R85 “R31,R51” R11 “R122,R132” “R1,R2,R55,R56,R57,R62” “R124,R127,R130,R131,R149,R156” “R158,R160,R162,R164,R174,R176” “R178,R61” “R83,R92,R99,R104” “R16,R116” “R125,R126,R128,R129,R138,R159” “R74,R112” “RA11,RA12,RA13,RA22,RA23,RA31” “RA1,RA2,RA3,RA4,RA5,RA6” “RA16,RA17,RA18,RA19,RA20,RA21” “RA24,RA25,RA26,RA27,RA28,RA29” “RA30,RA32” “RA7,RA8,RA9,RA10,RA14,RA15” “C106,C107,C113,C114,C125” “C11,C12,C13,C14,C31,C32” “C136,C137,C138,C139,C140,C141” “C147,C148,C149,C150,C159,C160” “C161,C162,C163,C164,C172,C173” “C174,C175,C176,C177,C178,C179” “C185,C187,C188,C189,C190,C191” “C192,C194,C213,C214,C215,C217” “C2,C3,C7,C8,C9,C10” “C218,C219,C209” Samsung Electronics Q’ty 2 3 2 1 1 1 1 1 1 1 1 1 2 2 1 2 1 5 3 4 1 2 6 6 6 6 6 6 4 1 6 6 6 6 6 5 5 6 1 1 6 5 6 3 1 1 2 1 2 6 6 6 2 4 2 6 2 6 6 6 6 2 6 5 6 6 6 6 6 6 6 6 3 Description/Specification Svc. DIODE-ARRAY “DA204K,20V,100mA,C2-3,SOT-23,T” IC-CMOS LOGIC “74ACT32,OR GATE,SOP,14P,150MIL” IC-TTL “74F14,INVERTER,SOP,14P,150MIL,” IC-TTL “74F08,AND GATE,SOP,14P,150MIL,” IC-TTL “74F04,INVERTER,SOP,14P,150MIL,” IC-TTL “74F74,D FLIP-FLOP,SOP,14P,150M” IC-TTL “74LS273,D FLIP-FLOP,SOP,20P,30” IC-TTL “74F273,D FLIP-FLOP,SOP,20P,300” IC-TTL “74F1071,ESD,SOP,20P,-,-,TP,PLA” IC-USC “USBN9602-28M,8BIT,SOP,28P,300MIL,48MHZ,ST,3.3V,-,0TO+70C” IC-LINE TRANSCEIVER “74ACT245,SOP,20P,-,OCTAL,ST,PL” IC-EEPROM “93C66,256x16BIT,SOP,8P,150MIL,” IC-DRAM “416C1204,1Mx16BIT,SOJ,42P,400M” IC-FLASH MEMORY “29F800,512Kx16BIT,TSOP,48P,720” IC-VOL. SUPERVISORY “7705,SOP,8P,150MIL,PLASTIC,20V” IC-POSI.FIXED REG. “33269,DPAK,3P,265MIL,3.37/3.33V40TO+150C,800MA,-,ST” R-CHIP “39OHM,5%,1/8W,DA,TP,2012” R-CHIP “0OHM,5%,1/8W,DA,TP,2012” R-CHIP “0OHM,5%,1/8W,DA,TP,2012” R-CHIP “0OHM,5%,1/8W,DA,TP,2012” R-CHIP “1.5KOHM,5%,1/8W,DA,TP,2012” R-CHIP “100OHM,5%,1/8W,DA,TP,2012” R-CHIP “100OHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10KOHM,5%,1/8W,DA,TP,2012” R-CHIP “10OHM,5%,1/8W,DA,TP,2012” R-CHIP “10OHM,5%,1/8W,DA,TP,3216” R-CHIP “180OHM,5%,1/8W,DA,TP,2012” R-CHIP “1KOHM,5%,1/8W,DA,TP,2012” R-CHIP “1KOHM,5%,1/8W,DA,TP,2012” R-CHIP “1KOHM,5%,1/8W,DA,TP,2012” R-CHIP “1KOHM,5%,1/8W,DA,TP,2012” R-CHIP “1MOHM,5%,1/8W,DA,TP,2012” R-CHIP “2.2KOHM,5%,1/8W,DA,TP,2012” R-CHIP “20OHM,5%,1/8W,DA,TP,2012” R-CHIP “2KOHM,5%,1/8W,DA,TP,2012” R-CHIP “3.3KOHM,5%,1/8W,DA,TP,2012” R-CHIP “33OHM,5%,1/8W,DA,TP,2012” R-CHIP “33OHM,5%,1/8W,DA,TP,2012” R-CHIP “33OHM,5%,1/8W,DA,TP,2012” R-CHIP “33OHM,5%,1/8W,DA,TP,2012” R-CHIP “33OHM,5%,1/8W,DA,TP,2012” R-CHIP “470OHM,5%,1/8W,DA,TP,2012” R-CHIP “5.1KOHM,5%,1/8W,DA,TP,2012” R-CHIP “68OHM,5%,1/8W,DA,TP,2012” R-NETWORK “100OHM,5%,1/16W,L,CHIP,8P,TP” R-NETWORK “39ohm,5%,1/16W,L,CHIP,8P,TP” R-NETWORK “39ohm,5%,1/16W,L,CHIP,8P,TP” R-NETWORK “39ohm,5%,1/16W,L,CHIP,8P,TP” R-NETWORK “39ohm,5%,1/16W,L,CHIP,8P,TP” R-NETWORK “39ohm,5%,1/16W,L,CHIP,8P,TP” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” N N N N N N N N N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y 7-1 Electrical Parts List Controller Board Lev SEC Code 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 7-2 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000192 2203-000239 2203-000239 2203-000239 2203-000239 2203-000274 2203-000274 2203-000274 2203-000316 2203-000361 2203-000455 2203-000455 2203-000455 2203-000595 2203-000595 2203-000634 2203-000634 2203-000818 2203-000818 2203-000938 2203-000938 2203-001002 2203-001158 2404-000128 2404-000308 2404-000308 2801-003699 2804-000378 2804-001230 2901-000229 2901-000229 2901-000235 3301-000271 3301-001034 3301-001074 3301-001074 3702-000118 3702-001104 3702-001121 3709-000177 3711-001091 3711-003204 3711-003205 3722-001101 4701-001020 JC09-00001A JC11-10507A JC11-10510A JC13-00002A JC41-00005A JC61-70938A JC62-30905A Location NO. “C220,C127,C132,C133,C134,C135” “C34,C35,C36,C37,C38,C42” “C43,C44,C45,C46,C47,C49” “C50,C52,C59,C60,C61,C65” “C66,C70,C75,C80,C81,C85” “C86,C89,C90,C91,C93,C94” “C97,C100,C102,C103,C104,C105” “C122,C123,C124,C167,C168” “C15,C16,C18,C25,C26,C27” “C21,C28,C39,C41,C48,C53” “C54,C64,C72,C88,C121,C131” “C210,C211,C212” “C55,C56,C57,C58” “C67,C68,C69,C87,C118” C95 “C84,C29,C221” “C195,C196,C197,C198,C199,C200” C201 “C92,C101,C108,C152,C154,C156” “C128,C129,C130,C142,C143,C144” “C145,C146” “C17,C71,C96,C111,C112,C119” “C20,C4” “C30,C63,C73,C74,C76,C77” “C78,C79,C99,C109,C110,C216” “C151,C153,C155,C158,C165,C166” “C169,C170,C181,C182,C183,C184” C40 C83 “C62,C82,C186,C19” “C1,C5,C24,C120,C126,C157” “C180,C193” Y1 Y2 Y3 “LF2,LF3,LF4,LF5,LF7,LF8” “LF9,LF10,LF11,LF12,LF14,LF15” LF13 B14 R88 “B1,B2,B6,B7,B8,B9” “B10,B11,B12,B13,R73” J11 J10 J4 “J2,J3” J12 J7 J6 CN2 “U14,U6” U18 U22 U13 U32 ML-6100 CONT(SPGP) U32 U32 Q’ty 6 6 6 6 6 6 6 5 6 6 6 3 4 5 1 3 6 1 6 6 2 6 2 6 6 6 6 1 1 4 6 2 1 1 1 6 6 1 1 1 6 5 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 Description/Specification Svc. “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “100nF,+80-20%,50V,Y5V,TP,2012,” “C-CERAMIC,CHIP” “.1NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “.1NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “.1NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “.1NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “10pF,0.25pF,50V,NPO,TP,2012,2.” “C-CERAMIC,CHIP” “10pF,0.25pF,50V,NPO,TP,2012,2.” “C-CERAMIC,CHIP” “10pF,0.25pF,50V,NPO,TP,2012,2.” “C-CERAMIC,CHIP” “120pF,5%,50V,NPO,TP,2012,-” “C-CERAMIC,CHIP” “150pF,5%,50V,NPO,TP,2012,-” “C-CERAMIC,CHIP” “1nF,5%,50V,NPO,TP,2012,-” “C-CERAMIC,CHIP” “1nF,5%,50V,NPO,TP,2012,-” “C-CERAMIC,CHIP” “1nF,5%,50V,NPO,TP,2012,-” “C-CERAMIC,CHIP” “.22NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “.22NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “22pF,5%,50V,NPO,TP,2012,-” “C-CERAMIC,CHIP” “22pF,5%,50V,NPO,TP,2012,-” “C-CERAMIC,CHIP” “.033NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “.033NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “.47NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “.47NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “.047NF,5%,50V,NPO,TP,2012” “C-CERAMIC,CHIP” “.068NF,5%,50V,NPO,TP,2012” “C-TA,CHIP” “10uF,20%,16V,-,TP,6032,-” “C-TA,CHIP” “33uF,20%,10V,-,TP,7342,4.4mm” “C-TA,CHIP” “33uF,20%,10V,-,TP,7342,4.4mm” CRYSTAL-UNIT “48MHz,50ppm,28-ABM,12pF,80ohm,” OSCILLATOR-CLOCK “40MHz,100ppm,10 TTL,-,5V,30mA” OSCILLATOR-CLOCK “47.7789MHz,50ppm,10TTL & CMOS,” FILTER-EMI SMD “50V,300mA,-,22nF,4.5x1.8x3.2mm” FILTER-EMI SMD “50V,300mA,-,22nF,4.5x1.8x3.2mm” FILTER-EMI SMD “50V,300mA,-,150pF,4.5x1.8x3.2,” CORE-FERRITE BEAD “-,-,-,-” CORE-FERRITE BEAD “AB,2.0x1.25x0.9mm,-,-” CORE-FERRITE BEAD “AB,2.0x1.25x0.9mm,-,-” CORE-FERRITE BEAD “AB,2.0x1.25x0.9mm,-,-” CONNECTOR-RIBBON “36P,FEMALE,ANGLE,AU” CONNECTOR-RIBBON “30P,FEMALE,STRAIGHT,AU” CONNECTOR-RIBBON “60P,MALE,STRAIGHT,AUF” CONNECTOR-CARD EDGE “72P,1.27mm,ANGLE,SN” CONNECTOR-HEADER “BOX,7P,1R,2.5mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,24P,2R,2mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,4P,1R,2.0mm,STRAIGHT,SN” JACK-USB “4P/2C,8.38mm,AU,IVR,#22-28” FREQ-ATTENUATOR “5-80MHz,15dB,-,0.03W” IC MICRO COMPUTER-CPU “ML-6100,IBM25EMPPC603EPG-,32X32MM” IC MASK ROM-HIGH “ML-165,KM23C8105DG,SOP,44P,600” “IC MASK ROM-PCL6,LOW” “ml-165,KM23C8105DG,SOP,44P,600” IC-ASIC-SPGP1 “ML-7000,SPGP1,QFP,240P,34.6X4.15BSC” PCB—CONTRLLER(NETWORK) “ML-6100N,FR4,-,1.6T,-” SPRING-CLIP “ML-6000,SUS304CSP,0.6*3.5,-,44” HEAT SINK-CPU “ML-6000,AL6063,-” Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N Y Y Y Y Y Y Y Y Y Y Y N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N Y Y Samsung Electronics Electrical Parts List 07-2 Engine Board(SEUK) Lev SEC Code 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0201-000008 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0402-000012 0402-000104 0402-000129 0402-000129 0402-000351 0402-000468 0402-001193 0402-001193 0403-000227 0403-000338 0403-000346 0403-000356 0403-000475 0403-000554 0501-000010 0501-000010 0501-000010 0501-000294 0501-000294 0502-000245 0502-001124 0604-000142 0604-000146 0604-001033 0801-000528 0801-000722 0803-000679 0803-001097 0903-000219 1103-001045 1201-000229 1202-000103 1203-000002 1203-000258 1203-000531 1404-000167 1405-000147 2001-000002 2001-000003 2001-000003 2001-000003 2001-000005 2001-000010 2001-000012 2001-000015 2001-000016 2001-000019 2001-000023 2001-000027 2001-000045 2001-000105 2001-000118 2001-000221 2001-000273 2001-000281 2001-000281 2001-000281 2001-000281 2001-000294 2001-000319 2001-000331 2001-000362 2001-000362 2001-000429 2001-000429 2001-000429 Location NO. “D154,D209” “D215,D220” “D221,D222,D223,D224” “D225,D226,D227,D228” “D229,D230,D231,D232” “D233,D401” “D4,D5,D6,D7,D101” “D500,D501,D502” “D504,D505” D102 DB101 “D1,D216,D217” D503 D103 “D205,D206,D207,D208” “D201,D202,D203,D204” D210 ZD102 ZD103 “ZD152,ZD204,ZD205” “ZD151,ZD201” “ZD101,ZD203” ZD202 Q211 “Q3,Q4,Q8,Q10,Q208” “Q500,Q503” “Q207,Q209” “Q501,Q502” Q9 “Q201,Q202,Q203,Q204” “PC152,PC153” PC151 “OP1,OP2,OP3,OP4” U4 U6 U205 U203 U3 U2 U201 U5 U151 U202 U101 TH101 TNR101 R107 JP122 “R25,R52,R111,R151” R406 “R221,R231” R240 R236 R62 R8 “R217,R230” R109 R104 R274 R14 R103 R39 R238 “R15,R24,R29,R30,R31” “R155,R252,R282,R283” “R284,R285,R293,R422” R514 R205 R215 “R56,R63” “R16,R23,R64” R512 “R18,R33,R34” R408 “R41,R42,R44,R45,R46” Samsung Electronics Q’ty 0 2 2 4 4 4 2 5 3 2 1 1 3 1 1 4 4 1 1 1 3 2 2 1 1 5 2 2 2 1 4 2 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 2 1 1 1 1 2 1 1 1 1 1 1 1 5 4 4 1 1 1 2 3 1 3 1 5 Description/Specification ADHESIVE-HM “PP_#3748,WHT,6500CPS,-” DIODE-SWITCHING “1N4148,100V,200MA,DO-35,TP” DIODE-SWITCHING “1N4148,100V,200MA,DO-35,TP” DIODE-SWITCHING “1N4148,100V,200MA,DO-35,TP” DIODE-SWITCHING “1N4148,100V,200MA,DO-35,TP” DIODE-SWITCHING “1N4148,100V,200MA,DO-35,TP” DIODE-SWITCHING “1N4148,100V,200MA,DO-35,TP” DIODE-SWITCHING “1N4148,100V,200MA,DO-35,TP” DIODE-SWITCHING “1N4148,100V,200MA,DO-35,TP” DIODE-SWITCHING “1N4148,100V,200MA,DO-35,TP” DIODE-RECTIFIER “UF4007,1KV,1A,DO-41,TP” DIODE-BRIDGE “D3SBA60,600V,4A,-,ST” DIODE-RECTIFIER “1N4003,200V,1A,DO-41,TP” DIODE-RECTIFIER “1N4003,200V,1A,DO-41,TP” DIODE-RECTIFIER “1N4937,600V,1A,DO-41,TP” DIODE-RECTIFIER “ESJS58-06,6KV,2mA,DO-201” DIODE-RECTIFIER “SHV-04,4KV,20mA,-,TP” DIODE-RECTIFIER “SHV-04,4KV,20mA,-,TP” DIODE-ZENER “1N751A,5.1V,5%,500mW,DO-35,TP” DIODE-ZENER “UZ27BM,27V,25.7-28.0V,500mW,DO” DIODE-ZENER “UZ33B,33V,30-36V,500mW,DO-35,T” DIODE-ZENER “UZ5.6BCB,5.6V,5.46-5.7V,500mW,” DIODE-ZENER “1N5274B,130V,5%,500mW,DO-35,TP” DIODE-ZENER “UZ7.5BM,7.2-7.7V,500mW,DO-35,T” TR-SMALL SIGNAL “KSC1008,NPN,800mW,TO-92,TP,120” TR-SMALL SIGNAL “KSC1008,NPN,800mW,TO-92,TP,120” TR-SMALL SIGNAL “KSC1008,NPN,800mW,TO-92,TP,120” TR-SMALL SIGNAL “KSA708-Y,PNP,800mW,TO-92,TP,12” TR-SMALL SIGNAL “KSA708-Y,PNP,800mW,TO-92,TP,12” TR-POWER “KSB1151-Y,PNP,1.3W,TO-126,-,16” TR-POWER “KSD526,NPN,30W,TO-220,BK,120-2” PHOTO-COUPLER “TR,-,200mW,DIP-4,ST” PHOTO-COUPLER “TRIAC,-,250mW,DIP-6,ST” PHOTO-INTERRUPTER“TR,-,150mW,DIP-4,ST” IC-CMOS LOGIC “74HCT574,D FLIP-FLOP,DIP,20P,3” IC-CMOS LOGIC “74HC245,TRANSCEIVER,DIP,20P,30” IC-TTL “7406,BUFFER/DRIVER,DIP,14P,300” IC-TTL “7407,BUFFER/DRIVER,DIP,14P,300” IC-MICROCOMPUTER“88C4316,8BIT,DIP,64P,-,8MHz,ST” IC-EEPROM “27E512,64Kx8BIT,DIP,28P,600MIL” IC-OP AMP “324,DIP,14P,300MIL,QUAD,100V/m” IC-VOLTAGE COMP. “393,DIP,8P,300MIL,DUAL,36V,CMO” IC-POSI.ADJUST REG.“431,TO-92,3P,-,PLASTIC,2.44/2.” IC-POSI.FIXED REG. “7818,TO-220,3P,-,PLASTIC,17.3/” IC-SWITCH VOL. REG.“5311,DIP,8P,300MIL,PLASTIC,-,3” THERMISTOR-NTC “5ohm,10%,3150K,18.7mW/C,TP” VARISTOR “470V,4500A,17x12mm,BK” R-CARBON(S) “200KOHM,5%,1/2W,AA,TP,6.4X2.4MM” R-CARBON “330OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “330OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “330OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “390OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “68KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “680KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON(S) “0.5OHM,5%,1/2W,AA,TP,2.4X6.4MM” R-CARBON(S) “1OHM,5%,1/2W,AA,TP,2.4X6.4MM” R-CARBON(S) “10OHM,5%,1/2W,AA,TP,2.4X6.4MM” R-CARBON “47OHM,5%,1/4W,AA,TP,2.4X6.4MM” R-CARBON “100OHM,5%,1/4W,AA,TP,2.4X6.4MM” R-CARBON “1.8KOHM,5%,1/4W,AA,TP,2.4X6.4MM” R-CARBON “1.5KOHM,5%,1/4W,AA,TP,2.4X6.4MM” R-CARBON(S) “180OHM,5%,1/2W,AA,TP,2.4X6.4MM” R-CARBON “1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “100KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “100OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “100OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “100OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “100OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “10MOHM,5%,1/4W,AA,TP,2.4X6.4MM” R-CARBON “120KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “12KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “150OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “150OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “1KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “1KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “1KOHM,5%,1/8W,AA,TP,1.8X3.2MM” Svc. N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y 7-3 Electrical Parts List Engine Board Lev SEC Code 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 7-4 2001-000429 2001-000435 2001-000449 2001-000449 2001-000515 2001-000552 2001-000563 2001-000565 2001-000577 2001-000660 2001-000660 2001-000660 2001-000734 2001-000734 2001-000761 2001-000780 2001-000786 2001-000812 2001-000812 2001-000812 2001-000812 2001-000816 2001-000832 2001-000864 2001-001015 2001-001070 2001-001093 2001-001119 2001-001119 2001-001150 2001-001165 2003-000703 2003-000706 2004-000002 2004-000003 2004-000345 2004-000345 2004-000345 2004-000385 2004-000433 2004-000544 2004-000691 2004-000699 2004-000754 2004-000869 2004-000884 2004-000900 2004-000965 2004-001156 2004-001231 2004-001315 2004-001315 2004-001357 2004-001357 2004-002001 2004-004179 2004-004425 2005-000168 2009-001041 2009-001042 2009-001082 2009-001083 2009-001084 2009-001085 2103-000156 2103-000270 2103-001079 2201-000003 2201-000004 2201-000004 2201-000017 2201-000017 2201-000017 2201-000019 2201-000023 2201-000119 2201-000119 Location NO. R49 R502 “R48,R225,R250,R256” “R501,R504” “R27,R424,R425,R426” R112 R253 R517 R152 R249 “R257,R263,R266” “R500,R503,R507” R110 R251 R218 R156 “R54,R223,R224,R227” “R19,R26,R28,R35,R36” “R261,R405” “R38,R40,R51,R59” “R60,R61,R260” R113 “R20,R407” “R53,R248” R262 R102 R292 “R210,R212,R226,R229” R239 “R101,R105” “R216,R219” “R157,R158” R108 R247 R237 “R17,R22,R55,R222” R43 R513 “R510,R268” “R58,R213” R508 R153 “R516,R57” R511 R154 R37 R47 R243 R509 R269 R234 R505 R233 R515 R245 R258 R506 R114 “R208,R209” “R204,R207,R277” R280 R220 R211 R201 “VR201,VR202,VR204” VR203 VR205 C203 C220 C404 “C17,C22,C27,C29” “C31,C38,C39,C40,C41” “C42,C43,C45,C237” “C106,C501” “C103,C104,C115” C209 “C222,C226,C227,C229” Q’ty 1 1 4 2 4 1 1 1 1 1 3 3 1 1 1 1 4 5 2 4 3 1 2 2 1 1 1 4 1 2 2 2 1 1 1 4 1 1 2 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 3 1 1 1 1 3 1 1 1 1 1 4 5 4 2 3 1 4 Description/Specification Svc. R-CARBON “1KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “1MOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “220OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “270OHM,5%,1/4W,AA,TP,2.4X6.4MM” R-CARBON “27KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “27OHM,5%,1/2W,AA,TP,3.3X9MM” R-CARBON “2KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “33KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “33KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “33KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “430OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “470OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “47KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “5.6OHM,5%,1/4W,AA,TP,2.4X6.4MM” R-CARBON “510OHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “56KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON “9.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM” R-CARBON(S) “120OHM,5%,1/2W,AA,TP,2.4X6.4MM” R-CARBON(S) “2.2KOHM,5%,1/2W,AA,TP,2.4X6.4MM” R-CARBON(S) “3.3MOHM,5%,1/2W,AA,TP,2.4X6.4MM” R-CARBON(S) “3.3MOHM,5%,1/2W,AA,TP,2.4X6.4MM” R-CARBON(S) “470KOHM,5%,1/2W,AA,TP,2.4X6.4MM” R-CARBON(S) “56OHM,5%,1/2W,AA,TP,2.4X6.4MM” R-METAL OXIDE(S) “470ohm,5%,3W,AA,TP,6x16mm” R-METAL OXIDE(S) “47Kohm,5%,2W,AA,TP,4.3x12mm” R-METAL “78.7Kohm,1%,1/8W,AA,TP,1.8x3.2” R-METAL “16.2Kohm,1%,1/8W,AA,TP,1.8x3.2” R-METAL “15Kohm,1%,1/8W,AA,TP,1.8x3.2mm” R-METAL “15Kohm,1%,1/8W,AA,TP,1.8x3.2mm” R-METAL “15Kohm,1%,1/8W,AA,TP,1.8x3.2mm” R-METAL “17.4Kohm,1%,1/8W,AA,TP,1.8x3.2” R-METAL “1Kohm,1%,1/8W,AA,TP,1.8x3.2mm” R-METAL “21.5Kohm,1%,1/8W,AA,TP,1.8x3.2” R-METAL “3.16Kohm,1%,1/8W,AA,TP,1.8x3.2” R-METAL “3.3Kohm,1%,1/8W,AA,TP,1.8x3.2m” R-METAL “309Kohm,1%,1/8W,AA,TP,1.8x3.2m” R-METAL “3Kohm,1%,1/8W,AA,TP,1.8x3.2mm” R-METAL “4.3Kohm,1%,1/8W,AA,TP,1.8x3.2m” R-METAL “4.7Kohm,1%,1/8W,AA,TP,1.8x3.2m” R-METAL “470Kohm,1%,1/8W,AA,TP,1.8x3.2m” R-METAL “619Kohm,1%,1/8W,AA,TP,1.8x3.2m” R-METAL “75Kohm,1%,1/8W,AA,TP,1.8x3.2mm” R-METAL “86.6Kohm,1%,1/8W,AA,TP,1.8x3.2” R-METAL “86.6Kohm,1%,1/8W,AA,TP,1.8x3.2” R-METAL “93.1Kohm,1%,1/8W,AA,TP,1.8x3.2” R-METAL “93.1Kohm,1%,1/8W,AA,TP,1.8x3.2” R-METAL “12.1Kohm,1%,1/8W,AA,TP,1.8x3.2” R-METAL “174KOHM,1%,1/8W,AA,TP,1.8X3.2MM” R-METAL “76.8KOHM,1%,1/8W,AA,TP,1.8X3.2MM” “R-WIRE WOUND,NON”“0.22ohm,5%,2W,AA,BK,4x12mm” R-METAL GLAZE “2Mohm,1%,1/4W,AA,TP,3X9mm” R-METAL GLAZE “4.7Mohm,1%,1/4W,AA,TP,3x9mm” R-METAL GLAZE “30Mohm,2%,2W,-,BK,30x8.5mm” R-METAL GLAZE “200Mohm,2%,1/2W,CM,BK,18x6mm” R-METAL GLAZE “30Mohm,2%,0.5W,CM,BK,18x6mm” R-METAL GLAZE “10Mohm,3%,1/2W,CM,BK,18x4mm” VR-SEMI “10Kohm,10%,1/2W,TOP” VR-SEMI “20Kohm,10%,1/2W,TOP” VR-SEMI “100Kohm,15%,1/2W,TOP” “C-CERAMIC,DISC” “68pF,10%,2KV,SL,TP,8x5,5” “C-CERAMIC,DISC” “100pF,10%,2KV,SL,TP,8x5,5” “C-CERAMIC,DISC” “100pF,10%,2KV,SL,TP,8x5,5” “C-CERAMIC,DISC” “1nF,10%,50V,Y5P,TP,4x3.5,5” “C-CERAMIC,DISC” “1nF,10%,50V,Y5P,TP,4x3.5,5” “C-CERAMIC,DISC” “1nF,10%,50V,Y5P,TP,4x3.5,5” “C-CERAMIC,DISC” “10nF,+80-20%,500V,Y5V,TP,13.5x” “C-CERAMIC,DISC” “2.2nF,20%,125V,Y5U,TP,11x7,5” “C-CERAMIC,DISC” “100nF,+80-20%,50V,Y5V,TP,8x3.5” “C-CERAMIC,DISC” “100nF,+80-20%,50V,Y5V,TP,8x3.5” Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Samsung Electronics Electrical Parts List Engine Board Lev SEC Code 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2201-000119 2201-000138 2201-000154 2201-000162 2201-000162 2201-000162 2201-000162 2201-000162 2201-000326 2201-000326 2201-000326 2201-000391 2201-000473 2201-000473 2201-000645 2201-000724 2201-000724 2201-002066 2201-002067 2202-000002 2202-000002 2202-000654 2301-000490 2305-001021 2306-000212 2401-000183 2401-000207 2401-000613 2401-000697 2401-001476 2401-001585 2401-001691 2401-001700 2401-002075 2801-000002 2902-001011 2902-001011 3301-000344 3601-000003 3601-000296 3602-000001 3704-000235 3711-000164 3711-000217 3711-000236 3711-000633 3711-000782 3711-000865 3711-001108 3711-002104 3711-002410 3711-002653 3711-003204 3711-003205 3711-003969 JC26-20301B JC26-20301D JC26-30506A JC27-40502A JC27-60101B JC27-60101C JC27-60501A JC27-60503A JC33-10501B JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A Location NO. “C26,C32,C34,C37,C46” “C16,C28,C30,C402” C108 “C1,C13,C14” C19 “C217,C231” “C24,C36” C405 “C221,C223,C225” C230 C500 “C20,C21” “C207,C208,C210,C214” C224 C111 “C201,C204,C219” “C202,C206” “C211,C212,C215,C216” C213 “C10,C12,C15,C18,C401” C502 “C110,C112” “C113,C505” C102 C101 “C156,C157” “C228,C503,C504,C506” “C109,C152” C151 C11 C114 C107 “C153,C154,C155” “C33,C35” X1 “BD1,BD101,BD102” “BD103,BD151,BD152” “FB1,FB2,FB3,FB4,FB5” F151 F101 “FH1,FH2,FH3,FH4” U2 CN4 CN101 CN12 CN3 CN105 CN103 CN6 CN102 CN104 CN7 CN5 CN2 “CN8,CN10” “T201,T202,T204” T101 T203 L103 L152 L151 L101 L102 “JP104~JP109” “JP110~,JP115” “JP116~JP120” “JP121~JP126” “JP127~JP132” “JP133~JP138” “JP139~JP143” “JP144,~JP148” “JP149~JP154” “JP155~JP160” “JP16,JP17,JP21~JP23” “JP161~JP166” “JP167~JP172” Samsung Electronics Q’ty 5 4 1 3 1 2 2 1 3 1 1 2 4 1 1 3 2 4 1 5 1 2 2 1 1 2 4 2 1 1 1 1 3 2 1 3 3 5 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 2 3 1 1 1 1 1 1 1 1 6 6 5 5 6 6 6 5 6 6 5 6 6 Description/Specification “C-CERAMIC,DISC” “100nF,+80-20%,50V,Y5V,TP,8x3.5” “C-CERAMIC,DISC” “100pF,10%,50V,Y5P,TP,4.0X4.0,2” “C-CERAMIC,DISC” “10nF,+80-20%,2KV,Y5P,TP,20x5,1” “C-CERAMIC,DISC” “10NF,+80-20%,50V,Y5V,TP,6.3X3,5” “C-CERAMIC,DISC” “10NF,+80-20%,50V,Y5V,TP,6.3X3,5” “C-CERAMIC,DISC” “10NF,+80-20%,50V,Y5V,TP,6.3X3,5” “C-CERAMIC,DISC” “10NF,+80-20%,50V,Y5V,TP,6.3X3,5” “C-CERAMIC,DISC” “10NF,+80-20%,50V,Y5V,TP,6.3X3,5” “C-CERAMIC,DISC” “2.2nF,10%,50V,Y5P,TP,6.5x3,5” “C-CERAMIC,DISC” “2.2nF,10%,50V,Y5P,TP,6.5x3,5” “C-CERAMIC,DISC” “2.2nF,10%,50V,Y5P,TP,6.5x3,5” “C-CERAMIC,DISC” “22pF,5%,50V,SL,TP,5.0x3.0,5” “C-CERAMIC,DISC” “33nF,+80-20%,50V,Y5V,TP,6x3,5” “C-CERAMIC,DISC” “33nF,+80-20%,50V,Y5V,TP,6x3,5” “C-CERAMIC,DISC” “680pF,5%,50V,SL,TP,10*3,5” “C-CERAMIC,DISC” “470pF,0.1,3KV,Y5P,TP,8x5,5” “C-CERAMIC,DISC” “470pF,0.1,3KV,Y5P,TP,8x5,5” “C-CERAMIC,DISC” “470pF,10%,6KV,Y5P,TP,10x7,10” “C-CERAMIC,DISC” “100pF,10%,6KV,Y5P,TP,8x7,10” “C-CERAMIC,MLC-AXIAL” “10nF,0.05,500V,X7R,TP,5.1x6.4x” “C-CERAMIC,MLC-AXIAL” “10nF,0.05,500V,X7R,TP,5.1x6.4x” “C-CERAMIC,MLC-RADIAL” “100nF,10%,50V,X7R,TP,5.1x6.6,5” “C-FILM,PEF” “4.7nF,5%,100V,TP,5.8x3.1x12.5,” “C-FILM,MPEF” “100nF,20%,275V,TP,17.5x7x13.5,” “C-FILM,MPPF” “470NF,20%,275V,BK,-,22.5” C-AL “1000uF,20%,35V,WT,TP,12.5x25,5” C-AL “100uF,20%,50V,WT,TP,8x12,5” C-AL “1uF,20%,50V,WT,TP,5x11,5” C-AL “2200uF,20%,16V,WT,TP,12.5x25,5” C-AL “47uF,20%,10V,GP,TP,6.3x5mm,2.5” C-AL “47uF,20%,50V,WT,TP,8x11.5,5” C-AL “150uF,20%,400V,WT,BK,30x25,10” C-AL “470uF,20%,10V,-,-,10x12.5,-” C-AL “4.7uF,20%,50V,GP,TP,5x11,5” CRYSTAL-UNIT “6.94407MHz,50ppm,28-AAM,20pF,5” FILTER-LINE “-,-,-” FILTER-LINE “-,-,-” CORE-FERRITE BEAD “ZZ,3.5x6.5mm,-,-” FUSE-FERRULE “250V,5A,FA,GLASS,20X5.2MM” FUSE-FERRULE “250V,5A,TL,CERAMIC,5X20MM” FUSE-CLIP “-,-,30mohm” SOCKET-IC “28P,DIP,SN,2.54mm” CONNECTOR-HEADER “1WALL,2P,1R,2.5mm,STRAIGHT,SN” CONNECTOR-HEADER “1WALL,3P,1R,3.96mm,STRAIGHT,SN” CONNECTOR-HEADER “1WALL,4P,1R,3.96mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,11P,1R,2mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,2P,1R,2.0mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,3P,1R,2mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,8P,1R,2mm,STRAIGHT,SN” CONNECTOR-HEADER “1WALL,2P,1R,7.92mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,10P,2R,2mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,3P,1R,2.5mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,24P,2R,2mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,4P,1R,2.0mm,STRAIGHT,SN” CONNECTOR-HEADER “BOX,2P,1R,2.5mm,STRAIGHT,SN” TRANS AF“ML-80,-,95MH” TRANS AF“ML-80,-,0.32WIRE” TRANS POWER-THV “ML-7000,-,57.5/1.3uH,180mH” COIL CHOCK-68UH “ML5500,68uH,0.04ohm,32T” COIL FILTER“-,9UH,-,-” COIL FILTER“-,6UH,-,-” COIL FILTER-LINE220V “ML5500,13.0mH,0.10ohm,-” COIL FILTER-3MH “ML5500,3.0mH,0.40ohm,30T” SOLENOID-6000 “ML-6000,24VDC,72W,57,39X39X22,” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” CBF HARNESS“ML-80,JUMPER,AWG22,52mm,SILVER” Svc. Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y 7-5 Electrical Parts List Engine Board Lev SEC Code 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 1 1 7-6 JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC39-40511A JC41-10529A JC70-10909A JC96-00319A 0402-000304 0402-000314 0502-001124 0505-000173 1401-000108 6003-000008 6003-000119 JC61-70100A JC62-20001A JC62-30001A JC62-30002A JF62-30201A JF68-30527H JF68-30527N Location NO. “JP173~JP177” “JP178,JP179,JP180,JP181,JP182” “JP188,JP189,JP190,JP191,JP192” “JP193~JP198” “JP199,JP200,JP203,JP187,JP268” “JP204,JP205,JP206,JP208” “JP209~JP214” “JP217~JP222” “JP223~JP228” “JP229~JP234” “JP25~JP31,JP216” “JP272~JP276,JP601” “JP33~JP39” “JP40~JP47” “JP49,JP50,JP51,JP52” “JP55~JP60,JP62,JP63” “JP602,JP605,JP616,JP7” “JP617,R412” “JP65~JP72” “JP73~JP80” “JP8,JP10,JP11,JP13” “JP81~JP88” “JP89~JP96” “JP97~JP103” “JS3,JS4,JS5,JP4,JP5,JP6” “HP1,HP2,HP3,HP4” D153 D152 “Q201,Q203” Q102 Q101 “Q201,Q101” “D152,D153,Q203” SMPS H/SINK Q102 “Q102,D152,D153” Q203 “Q101,Q201” - Q’ty 5 5 5 6 5 4 6 6 6 6 8 6 7 8 4 8 4 2 8 8 4 8 8 7 6 1 4 1 1 1 2 1 1 2 3 1 1 1 1 2 1 1 Description/Specification CBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSCBF HARNESSPCB-ENGINE IPR-CONNECTOR HV ELA HOU-H/SINK DIODE-RECTIFIER DIODE-RECTIFIER TR-POWER FET-SILICON THYRISTOR-TRIAC SCREW-TAPTITE SCREW-TAPTITE SPRING-PS TUBE-IRF840 HEAT SINK-TRANS HEAT SINK-SMPS HEAT SINK LABEL(R)-BAR CODE LABEL(R)-BAR CODE Svc. “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-80,JUMPER,AWG22,52mm,SILVER” “ML-5500,FR-1,1L,T1.6,247X299mm” “ML-80,AL,T0.8,-” “ML-80(SEA),-,USA,-,-,-,-” “STPR1020CF,200V,5A,TO-220,ST” “D10SC4M,40V,10A,ITO-220” “KSD526,NPN,30W,TO-220,BK,120-2” “SSP5N90,N,900V,5A,2.5ohm,150W,” “100A,600V,-,5V/uS,TO-220AB” “BH,+,S,M3,L4,ZPC3,SWRCH18A” “BH,+,B,M3,L8,CBLACK,SWRCH18A” “ML-66G,STS304-W1/2H,T0.5,-,-,-” “SSP5N90,IRF840,-,T0.45,L23,-” “ML-80,AL,-” “ML-80,AL,-” “HVPS,SPCC,t1.0” “SF1000,PY,38X6.5,T0.1,WHT” “SF500,PY,20X10,T0.1,WHT” Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N N N Y Y Y Y N Y Y Y N N Samsung Electronics Electrical Parts List 07-3 Panel Board Lev SEC Code 1 1 1 1 1 1 1 1 0601-000161 0601-000255 0601-000304 2001-000032 2202-000579 3404-000116 3711-001096 JC41-10003A Samsung Electronics Location NO. Q’ty 1 1 2 4 1 1 1 1 Description/Specification LED LED LED R-CARBON “C-CERAMIC,MLC-AXIAL” SWITCH-TACT CONNECTOR-HEADER PCB-PANEL LED “ROUND,GRN,5mm,563nm” “ROUND,RED,5mm,700nm” “ROUND,YEL,5mm,585nm” “180OHM,5%,1/4W,AA,TP,2.4X6.4MM” “100nF,+80-20%,50V,Z5U,TP,2.5x4” “12V,50mA,160gf,6X6X3.6mm,SPST” “BOX,7P,1R,2.5mm,ANGLE,SN” “ML-85/84,FR-4,2L,1.6T,47X71” Svc. N N N Y Y Y Y Y 7-7 Electrical Parts List 07-4 PTL Board Lev SEC Code 1 1 1 7-8 Location NO. 0601-001383 “LD1~LD10” 0601-001383 “LD11~LD18” JC41-10530A - Q’ty 10 8 1 Description/Specification LED LED PCB-PTL Svc. “ROUND,RED,3.0MM,700NM” “ROUND,RED,3.0MM,700NM” “ML-5500,FRI,1L,T1.6,218X8.5” Y Samsung Electronics 8. Schematic Diagrams 8-1. Engine Controller (1/6) +5V +5V D504 1N4148 CN105 1 2 +5V R516 3.3K 1/8 +5V SLCON2P D505 1N4148 A(0:15) AD(0:7) C15 10NF 500V MLC AXIAL U2 10 9 8 7 6 5 4 3 25 24 21 23 2 26 27 A(0) A(1) A(2) A(3) A(4) A(5) A(6) A(7) A(8) A(9) A(10) A(11) A(12) A(13) A(14) A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 20 CE* 22 OE* 1 VPP A(15) O0 O1 O2 O3 O4 O5 O6 O7 11 12 13 15 16 17 18 19 AD(0) AD(1) AD(2) AD(3) AD(4) AD(5) AD(6) AD(7) U4 A(0) A(1) A(2) A(3) A(4) A(5) A(6) A(7) +5V 28 C18 10NF 50V C13 10NF 50V GND 19 18 17 16 15 14 13 12 20 +5V VCC 10 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 D1 D2 D3 D4 D5 D6 D7 D8 2 3 4 5 6 7 8 9 U3 AD(0) AD(1) AD(2) AD(3) AD(4) AD(5) AD(6) AD(7) A(15) A(14) A(13) A(12) A(11) A(10) A(9) A(8) VCC GND 11 CLK 1 OC 74HCT574 14 R25 330 1/8 +5V FB4 FB5 NOT USED U6 A(15) 1 18 17 16 15 14 13 12 11 R406 3301/8 B1 B2 B3 B4 B5 B6 B7 B8 A1 A2 A3 A4 A5 A6 A7 A8 1 DIR 19 *G VCC GND 74LS06 2 3 4 5 6 7 8 9 AD(7) AD(6) AD(5) AD(4) AD(3) AD(2) AD(1) AD(0) +5V JS1 20 10 74HC245 CLN D401 1N4148 DCU_DATA DCU_CLK THERM SCF_CLUTCH SLEEP FUSER C401 CLUTCH 10NF SEL_CASSET 500V MLC AXIAL SUPPLY SCF_MOTOR 1 2 3 4 5 6 7 8 63 62 61 60 59 58 57 56 AD(0) AD(1) AD(2) AD(3) AD(4) AD(5) AD(6) AD(7) R36 5.6K 1/8 BDCORE BDCORE 27C256 PSIZE COVER FEED PEMPTY TONER EXIT +5V MP_PAPER SCF_EMPTY R408 1K U205-1 1/8 2 C14 10NF 50V 33 P2.0 31 P2.1 42 EA 52 49 48 47 46 45 22 39 38 9 11 12 30 36 55 +5V P1.0_AD0 P1.1_AD1 P1.2_AD2 P1.3_AD3 P1.4_AD5 P1.5_AD5 P1.6_AD6 P1.7_AD7 P5.7_ADC7 P5.4_ADC4 P5.3_ADC3 P5.2_ADC2 P5.1_ADC1 P5.0_ADC0 P3.2 P6.5 P6.4 LDON PMOTOR VDO LREADY 64 VDD 43 AVREF P0.7_A15 P0.6_A14 P0.5_A13 P0.4_A12 P0.3_A11 P0.2_A10 P0.1_A9 P0.0_P8 +5V P6.7 P6.6 P2.5 P2.7 P6.1 P4.6 P4.0 P3.7 P3.6 P3.5 P3.4 P3.3 P2.6 P2.4 P2.3 P5.5_ADC5 41 40 27 25 35 +5V R45 1K 1/8 3 PT_LAMP JS3 R27 C28 100PF 50V 23 24 51 37 34 C39 1NF 50V C40 1NF 50V C38 1NF 50V C29 1NF 50V C27 1NF 50V 100 220 1/8 READY CMSG EBUSY EMSG PSYNC CCLK MP_CLUTCH VDI HSYNC PRINT C19 0.01UF 50V R424 R425 R426 220 1/8 220 1/8 220 1/8 MOTOR_EA MOTOR_PB MOTOR_PA BIASPWM THVPWM THVREAD THVEA MHV 44 AVSS 32 VSS RESET* R34 1K 1/8 R422 54 XIN 53 XOUT P4.7 P4.5 P4.4 P2.2 P6.2 U205-2 4 74LS06 10 16 17 18 19 20 21 26 28 29 50 13 P4.3 14 P4.2 15 P4.1 P3.1 P3.0 P5.6_ADC6 P6.3 P6.0 +5V R33 1K 1/8 O:USED +5V KS88C4316 D7 1N4148 R56 12K 1/8 5 U5-2 Q1 Q0 6 Q2 C35 4.7UF 50V R53 56K 1/8 R54 47K 1/8 R31 100 1/8 R46 1K 1/8 R55 15K 1/8 X1 R52 7 LM393 C34 100NF 50V R407 510 1/8 FAN_E C405 10NF 50V VIDEO C20 22PF 50V 6.94407MHZ C21 22PF 50V JS5 JS6 SEC O O O X LM X O X O JS2 R405 JS2 FB1 C402 100PF 50V +5V R405 5.6K 1/8 330 1/8 C33 4.7UF 50V X:NOT USED JS3 JS4 MP EXIST BDCORE NON-EXIST 11 U205-5 10 13 U205-6 12 X O O X 74LS06 74LS06 Samsung Electronics 8-1 Schematic Diagrams Engine Controller (2/6) +5V +5V 1 2 3 4 DCU_DATA DCU_CLK SEL_CASSET SCF_MOTOR SCF_CLUTCH SCF_EMPTY SLCON4P-DCU C42 1NF 50V C41 1NF 50V +5V R282 R283 R284 R285 +24V +5V CN2 D228 1N4148 D229 1N4148 D230 1N4148 D231 1N4148 D224 1N4148 D225 1N4148 D226 1N4148 D227 1N4148 R61 5.6K 1/8 R60 5.6K 1/8 +5V R59 5.6K 1/8 CN6 1 2 3 4 5 6 7 8 100 1/8 100 1/8 100 1/8 100 1/8 SLCON8P-SCF CN5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 EBUSY EMSG CCLK PRINT VDI JS4 PSYNC READY HSYNC +5VT +5V CMSG TONER R293 R48 2.2K 1/8 D233 1N4148 C22 1NF 50V D232 1N4148 CN103 1 2 3 100 1/4 SLCON3P-TONER DLCON_24P-VIDEO C32 100NF 50V JS6 +5VT +24VS1 +5VS +5V +5V +5V +5V +5V +24VS1 C46 R28 5.6K 1/8 R62 0.5 1/2 100NF 50V CN3 11 10 9 8 7 6 5 4 3 2 1 R26 5.6K 1/8 R51 5.6K 1/8 R63 12K 1/8 CN7 R42 1K 1/8 R8 1 1/2 1 2 3 CLN SLCON3P-CLN U205-3 6 BD1 BDCORE 5 R29 100 1/8 PMOTOR 74LS06 LREADY HSYNC U203-3 6 JS5 LDON 5 +5V VDO 7407 SLCON11P C503 100UF 50V C26 100NF 50V C17 1NF 50V C16 100PF 50V C31 1NF 50V C30 100PF 50V C11 47UF 10V C24 10NF 50V C36 10NF 50V C231 10NF 50V +5V R517 33 1/2 CN10 1 2 SLCON2P-FAN C B PT_LAMP Q10 E KSC1008 8-2 Samsung Electronics Schematic Diagrams Engine Controller (3/6) T204 +24VS1 +18V +18V R234 86.6K 1/8 R262 9.1K 1/8 U203-1 2 1 BIASPWM R269 75K 1/8 C209 100NF 50V R223 47K 1/8 R412 10 R239 3.3M 1/2 R226 3.3M 1/2 R229 3.3M 1/2 2 LM324 R253 27K 1/8 D210 ESJA57-04 1 2 Q2 Q0 3 Q1 1 C219 470PF 3KV C220 100PF 2KV R231 390 1/8 R224 47K 1/8 4 1 HP1 SUPPLY 1 HP2 DEV ZD204 UZ33B ZD203 1N5274B ZD205 UZ33B U201-1 7407 5 VR204 C229 100NF 50V 10KOHM C223 2.2NF 500V D215 1N4148 C210 33NF 50V R222 15K 1/8 6 C TRANS10P Q204 KSD526 B R210 3.3M 1/2 R212 3.3M 1/2 E R268 17.4K 1/8 R230 10 1/2 R418 10K 1/8 9 SUPPLY U203-4 8 R416 2.2K 1/8 R415 3.3K 1/8 C R419 33K 1/8 B R413 33K 1/8 Q402 2SA1413 E +24VS1 C Q403 R414 KSC1008 E 1K 1/8 7407 C403 100PF 2KV R417 10K 1/8 B NOT USED +18V R258 174K 1/8 R233 93.1K 1/8 +5V 13 MHV U203-6 12 7407 +24VS1 1 IN C226 100NF 50V Samsung Electronics +18V U202 KA7818 VR203 20KOHM R257 33K 1/8 R261 5.6K 1/8 R266 33K 1/8 LM324 9 8 C227 100NF 50V C228 100UF 50V C217 10NF 50V D201 ESJA57-04 1 6 R227 47K 1/8 C404 100PF 2KV R218 430 1/8 C201 470PF 3KV R237 16.2K 1/8 4 10 5 D223 1N4148 C208 33NF 50V R205 10M 1/4 C TRANS10P B Q201 KSD526 E HS201 HEAT_SINK2 CN8 1 2 U201-3 C230 2.2NF 50V HP3 MHV 2 R217 10 1/2 OUT 3 GND 2 B Q211 KSC1008 E +24VS1 R238 100K 1/8 Q2 Q0 10 Q1 C 1 D202 ESJA57-04 C222 100NF 50V C204 470PF 3KV T202 +24VS1 R209 2M 1/4 R208 2M 1/4 R201 10M BR 1/4 SLCON2P-MHV R207 4.7M 1/4 R204 4.7M 1/4 8-3 Schematic Diagrams Engine Controller (4/6) T203 1 R249 33K 1/8 R240 68K 1/8 D216 1N4003 U201-2 LM324 5 Q1 Q0 6 Q2 R251 1.2K 1/8 R245 12.1K 1/8 C224 33NF 50V C225 2.2nF 50V R247 78.7K 1/8 D217 1N4003 R236 680K 1/8 7 D209 1N4148 R256 2.2K 1/8 R225 ZD201 ZD202 2.2K UZ5.6BCB UZ7.5BM 1/8 C221 2.2nF 50V R221 390 1/8 C213 100PF 6K C212 470PF 6K 4 5 C214 33NF 50V 6 C B Q203 KSD526 E C211 470PF 6K D207 ESJA58-06 R248 C 56K 1/8 2 R243 470K 1/8 D205 ESJA58-06 7407 Q209 KSA708 10 D208 ESJA58-06 E B VR202 10KOHM D206 ESJA58-06 U203-2 4 3 THVPWM R252 100 1/8 R274 1.8K 1/8 C215 470PF 6K C216 470PF 6K +24VS1 +18V R277 4.7M 1/4 1 HP4 THV R280 30M BR TRANS10P HS202 HEAT_SINK2 R220 200M BR +18V R216 56 1/2 R219 56 1/2 1 +18V C202 470PF 6K T201 6 D203 ESJA57-04 R509 619K,MF 1/8 1N4148 +5V +18V D501 C500 2.2nF 50V B Q500 KSC1008 R213 1K 1/8 C207 33NF 50V R507 33K 1/8 Q2 Q0 Q1 C203 68PF 2K C206 470PF 6K R211 30M BR 4 5 C Q502 C KSA708 13 14 R510 KSC1008 17.4K,MF E Q503 1/8 B R215 120K 1/8 B VR201 10KOHM R503 33K 1/8 1N4148 R508 21.5K,MF 1/8 E THVREAD C R506 75K 1/8 R515 68K 1/8 R504 2.2K 1/8 2 D204 ESJA57-04 D500 10 C B TRANS10P Q202 KSD526 E D503 1N4003 12 E LM324 U201-4 R505 56K 1/8 C505 4.7nF 50V 1N4148 C501 10nF 50V R511 309K 1/8 D502 VR205 100KOHM R501 2.2K 1/8 JP641 +18V R500 33K 1/8 E Q501 KSA708 B C R502 1M 1/8 +18V +5V R260 5.6K 1/8 THVEA 11 U203-5 10 R250 2.2K 1/8 E Q207 KSA708 B 7407 8-4 R263 33K 1/8 C Samsung Electronics Schematic Diagrams Engine Controller (5/6) +5V E +24VS1 FUSER R18 1K 1/8 +5V C37 100NF 50V +5V SLEEP R41 1K 1/8 9 B R40 5.6K 1/8 R292 2.2K 1/2 R49 1K 1/8 D221 1N4148 Q208 KSC1008 E 74LS06 R58 1K 1/8 R35 5.6K 1/8 R47 4.7K 1/8 D222 1N4148 R57 3.3K 1/8 C C43 Q8 1NF 50V KSC1008 E +5V R16 150 1/8 CLUTCH U5-1 B R20 510 1/8 1 D1 1N4003 B R19 5.6K 1/8 Q4 KSC1008 E LM393 CN4 BDCORE THERM FEED_CLUCH C504 100UF 50V E 2 Q1 Q0 2 Q2 C 1 C 3 B +24VS1 Q3 KSC1008 R37 4.3K 1/8 +5V U205-4 8 FUSERON C B C Q9 KSB1151-Y +24VS2 R44 1K 1/8 BDCORE C45 1NF 50V FB2 1 2 FB3 SLCON2P-THER +24VS2 +5V R38 5.6K 1/8 R17 15K 1/8 D4 1N4148 COVER R15 100 1/8 OP1 S58VT R39 1.2K 1/8 FEED C237 1NF 50V D220 1N4148 C10 10NF 500V MLC AXIAL +5V +5V R23 150 1/8 +24V R22 15K 1/8 CN104 R24 100 1/8 OP2 S58VT PEMPTY MOTOR_EA C12 10NF 500V MLC AXIAL MOTOR_PA FAN_E MOTOR_PB MP_PAPER MP_CLUTCH +5V 1 2 3 4 5 6 7 8 9 10 DLCON_10P R64 150 1/8 R43 15K 1/8 C506 47UF 50V R30 100 1/8 OP3 S58VT EXIT C1 10NF 50V +5V R512 150 1/8 R513 15K 1/8 R514 OP4 S58VT Samsung Electronics 100 1/8 PSIZE C502 10NF 8-5 Schematic Diagrams Engine Controller (6/6) F101 250V/T5A FH2 L102 6MH BD152 BDCORE 4 R105 470k 1/2 1 C104 2.2NF 250V 3 C107 150UF 400V DB101 D3SBA60 R106 100K ZD601 1N5274B 1/2 [V2] [V1] C108 10NF 250V R108 47K 2W 12 R107 200K 1/2 R157 470 3W SW152 M_SW 4 2 6 1 7 FUSERON FH3 1 R151 330 1/8 R153 3.16K 1/8 R109 47 1/4 BD102 BDCORE Q102 SSP5N90 D6 1N4148 1 R152 2K 1/8 D154 1N4148 PC152-1 PC123FY 1 2 D PC153-1 PC123FY G S C152 1UF 50V D101 1N4148 R113 5.6 1/4 4 U151 STL431_S R A 6 D103 1N4937GB 10 4 3 PC152-2 PC123FY R110 4.7K 1/8 +5V C155 470UF 10V JP622 JP623 JP614 +24VS2 +24V 1 2 3 4 5 GND OUT 4 IS+ VCC 6 CN12 C112 0.1UF 50V C111 680PF 50V C153 C154 470UF 470UF 10V 10V R155 100 1/8 +5VS 3 7 CT 2 FB 8 CS RT 1 U101 KA7552 R154 3K 1/8 11 ZD103 UZ27BM C110 100NF 50V MLC RADIAL 2 K BD103 BDCORE PC153-2 PC123FY 3 3 2 ZD151 UZ5.6BCB R14 1.5K 1/4 R104 100 1/4 +5VS FH4 L151 6UH 2 BD151 BDCORE 1 G PC151 MOC3061 +5V D152 D10SC4M C151 2200UF 16V ZD102 5.1V D5 1N4148 F151 +24VS1 HS101 HEAT_SINK2 C109 1UF 50V R158 470 3W R156 470 1/8 D102 UF4007 BD101 BDCORE Q101 TRIAC 3 2 3 R102 120 1/2 SLCON2P-LAMP MT2 1 2 C157 1000UF 35V 250V/5A MT1 C115 2.2NF 250V C106 10NF 500V 1 ZD152 UZ33B R103 180 1/2 CN102 L152 9UH C156 1000UF 35V 3 L103 300UH +24VS2 +24V D153 STPR1020CT 2 2 C102 100NF 250V 1 2 3 2 3 SW151 M_SW THERMISTER 4 1 C101 470NF 250V R101 470k 1/2 TNR101 TNR-471K 4 1 2 SLCON2P-AC 1 C103 2.2NF 250V CN101 T101 TRANS TH101 1 L101 11MH 3 FH1 R111 C113 330 4.7NF 1/8 50V C114 47UF 50V SLCON4P-POW SMPS[V1] R112 270 1/4 R114 0.22 1W DESCRIPTION 220NF,250V NO 1 LOCATION C101 2 C102 47NF,250V 3 4 C107 F101 220UF,200V 125V/8A 5 F151 125V/5A 6 PC152,PC153 PC817 7 Q102 IRF840 8 T101 1900UH 9 R114 0.1OHM,2W 10 R106,R107 100KOHM,1/2W 5 8-6 Samsung Electronics Schematic Diagrams 8-2. Controller Diagram(1/11) DATA(0:31) DH_R(0:31) ADDR(22) ADDR(20) ADDR(18) ADDR(16) RA28 39 1 3 5 7 RA27 39 1 3 5 7 RA25 39 1 3 5 7 RA24 39 1 3 5 7 RA32 39 7 5 3 1 RA30 39 7 5 3 1 ADDR(14) ADDR(12) ADDR(10) ADDR(8) RA29 39 7 5 3 1 8 6 4 2 A_R(17) A_R(19) A_R(21) A_R(23) ADDR(6) ADDR(4) ADDR(2) ADDR(0) RA26 39 7 5 3 1 8 6 4 2 A_R(25) A_R(27) A_R(29) A_R(31) 8 6 4 2 A_R(1) 8 6 4 2 A_R(9) A_R(11) A_R(13) A_R(15) A_R(5) A_R(7) VCC VCC VCC TT1 TSIZ(2) TSIZ(1) TSIZ(0) 1 3 5 7 C210 C211 10pF 10pF R192 10K 2 4 6 8 R154 nTS nBG R112 TS* 10K 10K R114 10K R115 0 10K 10K nAACK 10K UNUSED 149 TT0 TT1 TT2 TT3 TT4 U25 LF11 MC33269DT LF10 SCF451832-223T SCF451832-223T 1 3 3 2 1 3 IN OUT 2 2 TC0 TC1 *CI *WT *GBL Samsung Electronics 2 GND 1 R169 R168 R175 10K 10K 10K R142 10K 10K 235 *QACK 31 *QREQ R178 33 205 *LSSD_MODE 204 *L1_TSTCLK 203 *L2_TSTCLK R150 R148 R172 10K 10K 10K 213 PLL_CFG0 211 PLL_CFG1 210 PLL_CFG2 208 PLL_CFG3 R151 R174 R173 R149 10K 33 10K SYSCLK *TS C180 33UF 10V C214 C215 C217 100nF 100nF 100nF 209 C186 10uF 16V 1 3 5 7 DH_R(19) DH_R(18) DH_R(17) DH_R(16) 1 3 5 7 DH_R(15) DH_R(14) DH_R(13) DH_R(12) 1 3 5 7 DH_R(11) DH_R(10) DH_R(9) DH_R(8) 1 3 5 7 DH_R(7) DH_R(6) DH_R(5) DH_R(4) 1 3 5 7 DH_R(3) DH_R(2) DH_R(1) DH_R(0) 1 3 5 7 33 VCC R153 10K VCC R140 10K VCC R146 10K R139 10K nTA INT* RST* 33 212 SYSCLK 201 TCK 199 TDI 198 TDO R145 R171 10K 10K 200 TMS 202 *TRST R143 10K C216 33pF RST* C187 C163 C141 C164 C140 C139 C138 C137 C136 C135 C134 C133 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF U27 LF12 LF14 MC33269DT SCF451832-223T SCF451832-223T 1 3 1 3 3 2 IN OUT 2 10K 10K DH_R(23) DH_R(22) DH_R(21) DH_R(20) 3216 3.3V GND 1 R147 R144 1 3 5 7 VCC *TBST TSIZ0 TSIZ1 TSIZ2 R167 10 VCC 188 187 186 215 216 214 189 10K DH_R(27) DH_R(26) DH_R(25) DH_R(24) RA21 2 39 DATA(0) DATA(1) 4 DATA(2) 6 DATA(3) 8 RA20 39 DATA(4) 2 DATA(5) 4 DATA(6) 6 DATA(7) 8 RA19 2 39 DATA(8) DATA(9) 4 6 DATA(10) 8 DATA(11) RA18 2 39DATA(12) 4 DATA(13) 6 DATA(14) 8 DATA(15) RA17 2 39DATA(16) 4 DATA(17) 6 DATA(18) 8 DATA(19) RA16 2 39DATA(20) 4 DATA(21) 6 DATA(22) 8 DATA(23) RA15 2 39DATA(24) 4 DATA(25) 6 DATA(26) 8 DATA(27) RA14 2 39DATA(28) 4 DATA(29) 6 DATA(30) 8 DATA(31) APE C131 10pF UNUSED 33 R177 R176 219 *BR 27 *BG 36 *ABB 68 R156 R157 221 CLK_OUT 232 *RSRV 234 TBEN 233 *TLBSYNC U18 XPE603EFE100LL 32 *ARTRY 28 *AACK 10 10K *INT *SMI *MCP *CKSTP_IN *CKSTP_OUT *HRESET *SRESET 225 CSE0 150 CSE1 R155 R193 R123 VCC R152 R113 10pF R141 26 *DBG 25 *DBWO 145 *DBB 155 *TA 156 *DRTRY 154 *TEA 224 223 237 236 1 VCC VCC C212 R170 10K 191 190 185 184 180 R194 10K 192 197 196 195 153 *DBDIS 231 AP0 230 AP1 227 AP2 226 AP3 218 VCC 217 1 3 5 7 OGND0 OGND1 OGND2 OGND3 OGND4 OGND5 OGND6 OGND7 OGND8 OGND9 OGND10 OGND11 OGND12 OGND13 OGND14 OGND15 OGND16 OGND17 OGND18 OGND19 OGND20 OGND21 OGND22 RA31 100 TSIZ(0:2) R191 10K *DPE 38 40 41 42 46 47 48 50 DH_R(31) DH_R(30) DH_R(29) DH_R(28) 8 18 33 43 53 60 69 77 86 95 103 111 120 127 136 146 161 171 181 193 220 228 238 nTBST R190 10K DP0 DP1 DP2 DP3 DP4 DP5 DP6 DP7 R195 VCC A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 10K VCC DH0 DH1 DH2 DH3 DH4 DH5 DH6 DH7 DH8 DH9 DH10 DH11 DH12 DH13 DH14 DH15 DH16 DH17 DH18 DH19 DH20 DH21 DH22 DH23 DH24 DH25 DH26 DH27 DH28 DH29 DH30 DH31 A_R(24) A_R(26) A_R(28) A_R(30) 143 141 140 139 135 134 133 131 130 129 126 125 124 123 119 118 117 107 106 105 102 101 100 51 52 55 56 57 58 62 63 64 2 4 6 8 A_R(4) A_R(5) A_R(6) A_R(7) A_R(8) A_R(9) A_R(10) A_R(11) A_R(12) A_R(13) A_R(14) A_R(15) A_R(16) A_R(17) A_R(18) A_R(19) A_R(20) A_R(21) A_R(22) A_R(23) A_R(24) A_R(25) A_R(26) A_R(27) A_R(28) A_R(29) A_R(30) A_R(31) DL0 DL1 DL2 DL3 DL4 DL5 DL6 DL7 DL8 DL9 DL10 DL11 DL12 DL13 DL14 DL15 DL16 DL17 DL18 DL19 DL20 DL21 DL22 DL23 DL24 DL25 DL26 DL27 DL28 DL29 DL30 DL31 A_R(16) A_R(18) A_R(20) A_R(22) 179 2 178 3 176 5 175 6 174 7 170 11 169 12 168 13 166 15 165 16 164 17 160 21 159 22 158 23 151 30 144 37 GND0 GND1 GND2 GND3 GND4 GND5 GND6 GND7 GND8 GND9 GND10 GND11 GND12 GND13 GND14 ADDR(26) ADDR(24) 2 4 6 8 A_R(0) A_R(1) 9 19 29 39 49 65 116 132 142 152 162 172 182 206 239 ADDR(30) A_R(8) A_R(10) A_R(12) A_R(14) OVDD0 OVDD1 OVDD2 OVDD3 OVDD4 OVDD5 OVDD6 OVDD7 OVDD8 OVDD9 OVDD10 OVDD11 OVDD12 OVDD13 OVDD14 OVDD15 OVDD16 OVDD17 OVDD18 OVDD19 OVDD20 OVDD21 OVDD22 ADDR(7) ADDR(5) ADDR(3) ADDR(1) 2 4 6 8 10 20 35 45 54 61 70 79 88 96 104 112 121 128 138 148 173 183 194 222 229 240 163 ADDR(15) ADDR(13) ADDR(11) ADDR(9) A_R(4) A_R(6) VDD0 VDD1 VDD2 VDD3 VDD4 VDD5 VDD6 VDD7 VDD8 VDD9 VDD10 VDD11 VDD12 ADDR(23) ADDR(21) ADDR(19) ADDR(17) A_R(0) 2 4 6 8 AVDD ADDR(27) ADDR(25) 4 14 24 34 44 59 122 137 147 157 167 177 207 ADDR(31) 115DH_R(0) 114DH_R(1) 113DH_R(2) 110DH_R(3) 109DH_R(4) 108DH_R(5) 99 DH_R(6) 98 DH_R(7) 97 DH_R(8) 94 DH_R(9) 93DH_R(10) 92DH_R(11) 91DH_R(12) 90DH_R(13) 89DH_R(14) 87DH_R(15) 85DH_R(16) 84DH_R(17) 83DH_R(18) 82DH_R(19) 81DH_R(20) 80DH_R(21) 78DH_R(22) 76DH_R(23) 75DH_R(24) 74DH_R(25) 73DH_R(26) 72DH_R(27) 71DH_R(28) 68DH_R(29) 67DH_R(30) 66DH_R(31) A_R(0:31) ADDR(0:31) C218 C219 C220 C191 C192 C177 C178 C176 C179 C162 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF C159 C132 C160 C161 C174 C172 C175 C173 C189 C190 C188 C213 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 8-7 8-8 2 C61 100nF Y3 DXO-CLOCK 47.7789MHZ 4 VCC 3 OUT NC GND 1 2 C73 33pF 32 VSSP1 74 VSSP2 153 VSSP3 193 VSSP4 VCC R73 7 VSSO1 20 VSSO2 26 VSSO3 45 VSSO4 87 VSSO5 106 VSSO6 124 VSSO7 136 VSSO8 141 VSSO9 154 VSSO10 166 VSSO11 176 VSSO12 181 VSSO13 201 VSSO14 207 VSSO15 217 VSSO16 222 VSSO17 227 VSSO18 236 $O,$V,$P VSSO19 VCLK* 33 C71 22pF DRAMA(0:11) nDRAMRAS(0:3) nDRAMCAS(0:3) nDRAMWE nDRAMOE DRAMD(0:31) SPGP nIOCS4-OP2 nIOCS3-BUFFER_SEL nIOCS2-TONE_OUT nIOCS1-nIOCS5_JBIG nIOCS0 VDDO1 VDDO2 VDDO3 VDDO4 VDDO5 VDDO6 VDDO7 VDDO8 VDDO9 VDDO10 nEPRDY-RXD0 nEMSG nCMSG nEBSY nCBSY-TXD0 CCLK nPRINT VDO nLSYNC nFSYNC VCLK nRSTOUT nRESET MCLK2 MCLK nFAULT PERROR SELECT BUSY nACK nINIT nAUTOFD nSTROBE nSELECTIN PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 R57 R56 104 105 103 102 100 4 3 239 237 75 76 78 79 81 82 84 85 C41 100pF R58 R89 PD(0) PD(1) PD(2) PD(3) PD(4) PD(5) PD(6) PD(7) 33 33 EVIDEO* C72 13 39 83 115 131 159 171 186 212 231 U32 100pF C100 100nF 38 VDDP1 70 VDDP2 148 VDDP3 196 VDDP4 C101 C66 100nF R90 1nF C85 100nF VSSI1 VSSI2 VSSI3 VSSI4 VSSI5 VSSI6 VSSI7 VSSI8 VSSI9 VSSI10 VSSI11 DATA31 DATA30 DATA29 DATA28 DATA27 DATA26 DATA25 DATA24 DATA23 DATA22 DATA21 DATA20 DATA19 DATA18 DATA17 DATA16 DATA15 DATA14 DATA13 DATA12 DATA11 DATA10 DATA9 DATA8 DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 47 46 44 43 42 41 40 37 36 35 34 33 31 30 29 28 27 25 24 23 22 21 19 18 17 16 15 12 11 10 9 8 R45 R46 R47 10K 10K R72 10K 10K R49 R69 10K R78 10K 10K R60 R76 10K 10K DATA(31) DATA(30) DATA(29) DATA(28) DATA(27) DATA(26) DATA(25) DATA(24) DATA(23) DATA(22) DATA(21) DATA(20) DATA(19) DATA(18) DATA(17) DATA(16) DATA(15) DATA(14) DATA(13) DATA(12) DATA(11) DATA(10) DATA(9) DATA(8) DATA(7) DATA(6) DATA(5) DATA(4) DATA(3) DATA(2) DATA(1) DATA(0) 235 ADDR(31) 234 ADDR(30) 233 ADDR(27) 232 ADDR(26) 230 ADDR(25) 229 ADDR(24) 228 ADDR(23) 226 ADDR(22) 225 ADDR(21) 224 ADDR(20) 223 ADDR(19) 221 ADDR(18) 220 ADDR(17) 219 ADDR(16) 218 ADDR(15) 216 ADDR(14) 215 ADDR(13) 214 ADDR(12) 213 ADDR(11) 211 ADDR(10) 210 ADDR(9) 209 ADDR(8) 208 ADDR(7) 206 ADDR(6) 205 ADDR(5) 204 ADDR(4) 203 ADDR(3) 200 ADDR(2) 199 ADDR(1) 198 ADDR(0) R92 33 C118 C60 100nF C45 100nF ADDR31 ADDR30 ADDR27 ADDR26 ADDR25 ADDR24 ADDR23 ADDR22 ADDR21 ADDR20 ADDR19 ADDR18 ADDR17 ADDR16 ADDR15 ADDR14 ADDR13 ADDR12 ADDR11 ADDR10 ADDR9 ADDR8 ADDR7 ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0 DATA(31:0) 10pF C59 100nF C46 100nF 6 52 64 80 99 128 142 165 192 202 240 56 57 58 54 53 51 49 48 C99 C47 100nF C90 100nF TSIZ0 TSIZ1 TSIZ2 nTA nBG nTS nTBST TT1 33pF C42 100nF C49 100nF C89 100nF VDDI1 VDDI2 VDDI3 VDDI4 VDDI5 VDDI6 VDDI7 VDDI8 VDDI9 194 nRD 195 nWR C43 100nF C106 100nF 188 nROMCS0 189 nROMCS1 190 nROMCS2 191 nROMCS3 C50 100nF 1 TESTSE 2 TM ADDR(31:0) nROMCS(0) nROMCS(1) nROMCS(2) nROMCS(3) LF3 SCF451832-223T 1 3 C70 100nF C105 100nF DRAMD0 DRAMD1 DRAMD2 DRAMD3 DRAMD4 DRAMD5 DRAMD6 DRAMD7 DRAMD8 DRAMD9 DRAMD10 DRAMD11 DRAMD12 DRAMD13 DRAMD14 DRAMD15 DRAMD16 DRAMD17 DRAMD18 DRAMD19 DRAMD20 DRAMD21 DRAMD22 DRAMD23 DRAMD24 DRAMD25 DRAMD26 DRAMD27 DRAMD28 DRAMD29 DRAMD30 DRAMD31 C86 100nF C104 100nF 14 50 77 101 130 147 160 187 238 125 126 127 129 132 133 134 135 137 138 139 140 143 144 145 146 149 150 151 152 155 156 157 158 161 162 163 164 167 168 169 170 C44 100nF C103 100nF C120 33uF 10V DRAMD(0) DRAMD(1) DRAMD(2) DRAMD(3) DRAMD(4) DRAMD(5) DRAMD(6) DRAMD(7) DRAMD(8) DRAMD(9) DRAMD(10) DRAMD(11) DRAMD(12) DRAMD(13) DRAMD(14) DRAMD(15) DRAMD(16) DRAMD(17) DRAMD(18) DRAMD(19) DRAMD(20) DRAMD(21) DRAMD(22) DRAMD(23) DRAMD(24) DRAMD(25) DRAMD(26) DRAMD(27) DRAMD(28) DRAMD(29) DRAMD(30) DRAMD(31) C91 100nF 2 SPGP_5V 116 nDRAMCAS0 117 nDRAMCAS1 118 nDRAMCAS2 119 nDRAMCAS3 2 3 120 nDRAMRAS0 121 nDRAMRAS1 122 nDRAMRAS2 123 nDRAMRAS3 C102 100nF 1 nDRAMCAS(0) nDRAMCAS(1) nDRAMCAS(2) nDRAMCAS(3) R61 0 3 114 nDRAMWE 113 nDRAMOE LF8 SCF451832-223T 1 DRAMA0 DRAMA1 DRAMA2 DRAMA3 DRAMA4 DRAMA5 DRAMA6 DRAMA7 DRAMA8 DRAMA9 DRAMA10 DRAMA11 LF9 SCF451832-223T 172 173 174 175 177 178 179 180 182 183 184 185 VCC nDRAMRAS(0) nDRAMRAS(1) nDRAMRAS(2) nDRAMRAS(3) DRAMA(0) DRAMA(1) DRAMA(2) DRAMA(3) DRAMA(4) DRAMA(5) DRAMA(6) DRAMA(7) DRAMA(8) DRAMA(9) DRAMA(10) DRAMA(11) Schematic Diagrams Controller Diagram(2/11) VCC 55 CPUTYPE 197 A20 5 nIPL 59 nAACK R62 33 A20 TSIZ(0) TSIZ(1) TSIZ(2) R199 AD_20 INT* nAACK TSIZ(0:2) 180 nTA nBG nTS nTBST TT1 94 DMACK0-OP1 93 nDREQ0-IP1 89 TXD1-nSYSWAIT 88 RXD1-CH_STATUS nDREQ(0) TXD_1 RXD_1 91 DMACK1 90 nDREQ1 DMACK(1) nDREQ(1) 98 nWAIT-EIRQ3 97 EIRQ2 96 EIRQ1 95 EIRQ0 nWAIT EIRQ2 EIRQ1 EIRQ0 92 63 62 61 60 nIOCS4 nIOCS3 nIOCS2 nIOCS1 nIOCS0 108 110 112 111 109 107 RXD_0 nEMSG nCMSG nEBSY TXD_0 CCLK* 0 B10 10 B11 LSYNC nFSYNC VCLK* RST* nRESET SYSCLK MCLK nPRINT 66 71 69 72 73 68 67 86 65 nFAULT PERROR SELECT BUSY nACK nINIT nAUTOFD nSTROBE nSELECTIN B9 0 PD(0:7) WR* RD* C40 10pF Samsung Electronics Schematic Diagrams Controller Diagram(3/11) VCC VCC C97 100nF R84 10K VCC UNUSED R40 R35 R37 10K R105 R34 1 nTS 10K 10K 14 VCC CLR 10K 0 2 TS* nROMCS(0) D Q nROMCS(1) 5 R104 33 nTS U19-1 74F74 nROMCS(2) 3 SYSCLK CLK _Q C119 22pF 6 nROMCS(3) C57 10pF C58 10pF C56 C55 PR GND 10pF 10pF 4 7 RST* Y2 DXO-CLOCK 50MHZ VCC R55 33 LF5 SCF451832-223T 1 R74 68 3 4 C65 100nF 2 3 VCC NC 1 C83 68pF OUT GND 0 4 LF7 SCF451832-223T XIN VCC XOUT VI REF VO LF GND 8 1 R86 10K 7 6 2 R87 1K 5 R88 68 TXD0 R70 3 C82 10uF 16V C84 150pF MCLK 0 RXD_0 RXD0 R75 TXD_1 R68 10 C96 22pF C95 R71 3 2 100pF TXD_0 1 2 R85 2.2K VCC U14 FS741 0 C98 10pF TXD1 R77 0 RXD_1 RXD1 C69 C68 C87 C67 10pF 10pF 10pF 10pF VCC VCC VCC VCC VCC R106 10K 2 R116 R91 10K R93 10K R94 10K R95 10K 10K RA13 100 1 3 5 7 nIOCS4 nIOCS3 nIOCS2 nIOCS1 nIOCS0 C121 100pF Samsung Electronics C127 100nF R80 C122 100pF C123 100pF C124 100pF C126 33uF 10V 470 3 4 REF VCC *RESIN SENSE CT RESET GND *RESET TL7705ACD 2 4 6 8 R79 100 IOCS4 IOCS3 IOCS2 IOCS1 IOCS0 R81 1K C125 100nF U20 1 VCC C107 100nF R96 10K 8 U15-2 74F14 2 1 7 6 7 5 R82 14 U15-1 74F14 3 0 F_RST* 5 U15-3 74F14 6 13 U15-6 74F14 12 4 nRESET C92 1nF R97 10K C88 100pF 8-9 Schematic Diagrams Controller Diagram(4/11) VCC ADDR(2:25) DATA(0:31) U11 (L) ADDR(19) ADDR(18) ADDR(17) ADDR(16) ADDR(15) ADDR(14) ADDR(13) ADDR(12) ADDR(11) ADDR(10) ADDR(9) ADDR(8) ADDR(7) ADDR(6) ADDR(5) ADDR(4) ADDR(3) ADDR(2) U13 (L) 2 3 34 35 36 37 38 39 40 41 42 4 5 6 7 8 9 10 11 43 44 1 ADDR(20) ADDR(19) ADDR(18) ADDR(17) ADDR(16) ADDR(15) ADDR(14) ADDR(13) ADDR(12) ADDR(11) ADDR(10) ADDR(9) ADDR(8) ADDR(7) ADDR(6) ADDR(5) ADDR(4) ADDR(3) ADDR(2) ADDR(21) ADDR(22) ADDR(23) A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC2 NC3 NC1 12 CE* 14 OE* RCS1* D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 15 17 19 21 24 26 28 30 16 18 20 22 25 27 29 31 DATA(0) DATA(1) DATA(2) DATA(3) DATA(4) DATA(5) DATA(6) DATA(7) DATA(8) DATA(9) DATA(10) DATA(11) DATA(12) DATA(13) DATA(14) DATA(15) VCC 16 17 48 1 2 3 4 5 6 7 8 18 19 20 21 22 23 24 25 9 10 13 14 23 VCC 33 BHE 13 VSS1 32 VSS2 KM23C8105DG-LOW J2 822030-3 A20 26 28 11 C81 C113 100nF 100nF A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC1 NC2 NC3 NC4 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 VCC 45 43 41 39 36 34 32 30 44 42 40 38 35 33 31 29 DATA(15) DATA(14) DATA(13) DATA(12) DATA(11) DATA(10) DATA(9) DATA(8) DATA(7) DATA(6) DATA(5) DATA(4) DATA(3) DATA(2) DATA(1) DATA(0) VCC C52 100nF 37 R53 47 1 10K _BYTE VCC 46 VSS1 27 VSS2 11 12 13 14 15 16 17 18 19 20 21 22 23 28 29 31 32 33 34 40 41 ADDR(2) ADDR(3) ADDR(4) ADDR(5) ADDR(6) ADDR(7) ADDR(8) ADDR(9) ADDR(10) ADDR(11) ADDR(12) ADDR(13) ADDR(14) ADDR(15) ADDR(16) ADDR(17) ADDR(18) ADDR(19) ADDR(20) ADDR(21) ADDR(22) 42 43 RD_FLASH* WR_FLASH2* 45 RCS3* 47 F_RST* AM29F800B-90EC 2 3 34 35 36 37 38 39 40 41 42 4 5 6 7 8 9 10 11 43 44 1 ADDR(20) ADDR(19) ADDR(18) ADDR(17) ADDR(16) ADDR(15) ADDR(14) ADDR(13) ADDR(12) ADDR(11) ADDR(10) ADDR(9) ADDR(8) ADDR(7) ADDR(6) ADDR(5) ADDR(4) ADDR(3) ADDR(2) ADDR(21) ADDR(22) ADDR(23) A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC2 NC3 NC1 12 CE* 14 OE* RD* 66 67 68 69 70 71 VCC U22 (H) D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 15 17 19 21 24 26 28 30 16 18 20 22 25 27 29 31 DATA(16) DATA(17) DATA(18) DATA(19) DATA(20) DATA(21) DATA(22) DATA(23) DATA(24) DATA(25) DATA(26) DATA(27) DATA(28) DATA(29) DATA(30) DATA(31) VCC U8 (H) A20 ADDR(19) ADDR(18) ADDR(17) ADDR(16) ADDR(15) ADDR(14) ADDR(13) ADDR(12) ADDR(11) ADDR(10) ADDR(9) ADDR(8) ADDR(7) ADDR(6) ADDR(5) ADDR(4) ADDR(3) ADDR(2) 23 VCC 33 BHE 13 VSS1 32 VSS2 KM23C8105DG-HIGH 16 17 48 1 2 3 4 5 6 7 8 18 19 20 21 22 23 24 25 9 10 13 14 C149 C150 100nF 100nF 26 28 11 RCS0* RD_FLASH* WR_FLASH1* A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 VCC 45 43 41 39 36 34 32 30 44 42 40 38 35 33 31 29 DATA(8) DATA(9) DATA(10) DATA(11) DATA(12) DATA(13) DATA(14) DATA(15) 3 5 7 9 25 27 35 50 DATA(16) DATA(17) DATA(18) DATA(19) DATA(20) DATA(21) DATA(22) DATA(23) 52 54 56 58 60 62 64 38 DATA(24) DATA(25) DATA(26) DATA(27) DATA(28) DATA(29) DATA(30) DATA(31) 46 48 10 30 59 VCC C36 100nF 51 53 55 57 61 63 65 37 C147 100nF C75 100nF WR_FLASH3* 1 39 72 C34 100nF 37 47 1 _BYTE NC1 NC2 NC3 NC4 VCC DATA(31) DATA(30) DATA(29) DATA(28) DATA(27) DATA(26) DATA(25) DATA(24) DATA(23) DATA(22) DATA(21) DATA(20) DATA(19) DATA(18) DATA(17) DATA(16) DATA(0) DATA(1) DATA(2) DATA(3) DATA(4) DATA(5) DATA(6) DATA(7) 44 RCS2* _CE 15 1 _OE _BUSY 12 _WE_RESET 2 4 6 8 24 26 36 49 VCC R18 10K R7 0 RD* RD_FLASH* 6 9 U9-4 74F04SC 8 4 RCS3* _CE 15 _OE _BUSY 12 _WE_RESET 13 U5-4 11 74ACT32SCX F_RST* 5 11 U9-5 74F04SC 10 R32 13 U9-6 74F04SC 12 U12-4 74ACT32SCX 100 100 nROMCS(0) nROMCS(1) R39 R38 100 100 1 RCS0* C37 100nF 1 RCS1* FLASH_WR_E nROMCS(2) nROMCS(3) R36 R33 100 100 1 RCS2* 1 RCS3* 14 RCS2* C13 100nF VCC U5-2 6 74ACT32SCX WR_FLASH2* U5-3 8 74ACT32SCX WR_FLASH1* 12 14 1 RCS0* 10 U5-1 3 74ACT32SCX 7 WR* 4 11 5 U9-1 74F04SC 2 1 6 13 VCC R41 U4-2 74F08 WR_FLASH3* 12 AM29F800B-90EC NOT USED 5 U9-3 74F04SC 46 VSS1 27 VSS2 2 9 7 8-10 Samsung Electronics Schematic Diagrams Controller Diagram(5/11) J3-1 822030-3 DRAMD(0:31) DR_A(0:11) DRAMA(0:11) RA7 39 DRAMA(0) DRAMA(1) DRAMA(2) DRAMA(3) RA6 39 DRAMA(4) DRAMA(5) DRAMA(6) DRAMA(7) RA10 39 DRAMA(8) DRAMA(9) DRAMA(10) DRAMA(11) 1 3 5 7 2 4 6 8 DR_A(0) DR_A(1) DR_A(2) DR_A(3) 1 3 5 7 2 4 6 8 DR_A(4) DR_A(5) DR_A(6) DR_A(7) 1 3 5 7 2 4 6 8 DR_A(8) DR_A(9) DR_A(10) DR_A(11) 12 13 14 15 16 17 18 28 31 32 19 DR_A(0) DR_A(1) DR_A(2) DR_A(3) DR_A(4) DR_A(5) DR_A(6) DR_A(7) DR_A(8) DR_A(9) DR_A(10) 40 43 41 42 DR_CAS0* DR_CAS1* DR_CAS2* DR_CAS3* 34 44 DR_RAS1* 45 33 DR_RAS2* 29 46 66 71 DR_A(11) 47 DR_WR* C112 22pF R99 DR_WR* nDRAMWE 33 C111 22pF 2 4 6 8 20 22 24 26 36 49 51 53 55 57 61 63 65 37 3 5 7 9 21 23 25 27 35 50 52 54 56 58 60 62 64 38 67 68 69 70 RA11 100 1 3 5 7 C78 C74 C76 C77 33pF 33pF 33pF 33pF 2 4 6 8 DR_CAS0* DR_CAS1* DR_CAS2* DR_CAS3* C35 C80 C148 100nF 100nF 100nF U1 KM416C1200BLJ-6 RA12 100 1 3 5 7 nDRAMRAS(0) nDRAMRAS(1) nDRAMRAS(2) nDRAMRAS(3) C79 33pF C110 33pF C109 C63 33pF 33pF 2 4 6 8 DR_RAS0* DR_RAS1* DR_RAS2* DR_RAS3* DR_A(0) DR_A(1) DR_A(2) DR_A(3) DR_A(4) DR_A(5) DR_A(6) DR_A(7) DR_A(8) DR_A(9) 17 18 19 20 23 24 25 26 27 28 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 16 NC1 15 NC2 14 30 31 13 29 DR_RAS0* DR_CAS1* DR_CAS0* DR_WR* R1 33 Samsung Electronics DRAMD(8) DRAMD(9) DRAMD(10) DRAMD(11) DRAMD(12) DRAMD(13) DRAMD(14) DRAMD(15) DRAMD(16) DRAMD(17) DRAMD(18) DRAMD(19) DRAMD(20) DRAMD(21) DRAMD(22) DRAMD(23) DRAMD(24) DRAMD(25) DRAMD(26) DRAMD(27) DRAMD(28) DRAMD(29) DRAMD(30) DRAMD(31) VCC 1 39 72 10 30 59 nDRAMCAS(0) nDRAMCAS(1) nDRAMCAS(2) nDRAMCAS(3) DRAMD(0) DRAMD(1) DRAMD(2) DRAMD(3) DRAMD(4) DRAMD(5) DRAMD(6) DRAMD(7) RAS* UCAS* LCAS* WR* OE* 11 NC3 12 NC4 32 NC5 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQ16 VCC1 VCC2 VCC3 GND1 GND2 GND3 U2 KM416C1200BLJ-6 2 3 4 5 7 8 9 10 33 34 35 36 38 39 40 41 VCC DRAMD(0) DRAMD(1) DRAMD(2) DRAMD(3) DRAMD(4) DRAMD(5) DRAMD(6) DRAMD(7) DRAMD(8) DRAMD(9) DRAMD(10) DRAMD(11) DRAMD(12) DRAMD(13) DRAMD(14) DRAMD(15) C1 33UF 10V 17 18 19 20 23 24 25 26 27 28 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 16 NC1 15 NC2 VCC 14 30 31 13 29 DR_RAS0* DR_CAS3* DR_CAS2* DR_WR* 1 6 21 22 37 42 DR_A(0) DR_A(1) DR_A(2) DR_A(3) DR_A(4) DR_A(5) DR_A(6) DR_A(7) DR_A(8) DR_A(9) C8 C7 C9 100nF 100nF 100nF R2 33 RAS* UCAS* LCAS* WR* OE* 11 NC3 12 NC4 32 NC5 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQ16 VCC1 VCC2 VCC3 GND1 GND2 GND3 2 3 4 5 7 8 9 10 33 34 35 36 38 39 40 41 DRAMD(16) DRAMD(17) DRAMD(18) DRAMD(19) DRAMD(20) DRAMD(21) DRAMD(22) DRAMD(23) DRAMD(24) DRAMD(25) DRAMD(26) DRAMD(27) DRAMD(28) DRAMD(29) DRAMD(30) DRAMD(31) VCC 1 6 21 22 37 42 C11 C10 C2 100nF 100nF 100nF 8-11 Schematic Diagrams Controller Diagram(6/11) 1 U23 DATA(0:23) 3 4 7 8 13 14 17 18 DATA(0) DATA(1) DATA(2) DATA(3) DATA(4) DATA(5) DATA(6) DATA(7) D0 D1 D2 D3 D4 D5 D6 D7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 11 CP 1 _MR VCC GND VCC FLASH_WR_E 2 5 6 9 12 15 16 19 LCD_D4 LCD_D5 LCD_D6 LCD_D7 LCD_E LCD_RS LCD_DRV_E 1 2 VCC 1 VCC 20 2 C114 100nF 74LS273 (FAN) C222 100nF 3 VCC 10 RST* C194 100nF R181 10K J8-1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 LCD_E U16 U12-1 74ACT32SCX14 1 3 11 CP 1 _MR 2 WR* D0 D1 D2 D3 D4 D5 D6 D7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 VCC GND 7 LED1 LED2 DPO_RST* USB_RST* $V 1 2 3 4 VCC 20 CS VCC 8 7 SK DC DI ORG 6 5 DOGND 10 74F273SCX C196 1nF VCC C198 1nF C200 1nF C195 1NF C197 1NF C199 1NF U26 C185 100nF KM93C66G C93 100nF DF11-20DP-2DSA(20) (CONN20) 4 74F14 U28-3 5 C53 100pF C54 100pF 2 5 6 9 12 15 16 19 LED1 LED2 LCD_D4 LCD_D5 LCD_D6 LCD_D7 LCD_RS LCD_DRV_E 74F14 U28-2 3 VCC C38 100nF 3 4 7 8 13 14 17 18 DATA(8) DATA(9) DATA(10) DATA(11) DATA(12) DATA(13) DATA(14) DATA(15) J13-1 J13-2 LF13 ACF451832-151T C117 100nF U12-3 10 8 19 _G 1 DIR 9 74ACT32SCX VCC A1 A2 A3 A4 A5 A6 A7 A8 GND P_SW1 P_SW2 P_SW3 P_SW4 P_SW5 P_SW6 P_SW7 P_SW8 10 3 8 18 17 16 15 14 13 12 11 74ACT245 R111 33 C39 100pF B1 B2 B3 B4 B5 B6 B7 B8 74F14 U28-5 11 DATA(0) DATA(1) DATA(2) DATA(3) DATA(4) DATA(5) DATA(6) DATA(7) 74ACT32SCX RD* VCC U24 20 2 3 4 5 6 7 8 9 1 2 4 5 R182 R183 R184 R185 R186 R187 R189 R188 10K 10K 10K 10K 10K 10K 10K 10K 10 6 5 IOCS0 6 VCC 4 ADDR(15) 74F14 U28-4 9 J12-1 U12-2 6 7 P_SW1 P_SW2 P_SW3 P_SW4 P_SW5 P_SW6 P_SW7 P_SW8 VCC 14 1 U28-1 74F14 2 VCC 7 C201 1NF VCC VCC C94 100nF R166 10K U17 20 2 3 4 5 6 7 8 9 DATA(8) DATA(9) DATA(10) DATA(11) DATA(12) DATA(13) DATA(14) DATA(15) VCC A1 A2 A3 A4 A5 A6 A7 A8 19 _G 1 DIR R83 33 8-12 VCC B1 B2 B3 B4 B5 B6 B7 B8 GND 18 17 16 15 14 13 12 11 R101 R100 10K 100 VCC R103 10K C202 1NF C203 1NF C204 1NF C205 1NF C206 1NF C208 1NF C209 100nF C207 1NF 13 U28-6 74F14 VCC R198 10K 12 LED PANEL RDY* EXITP* nFSYNC BRDIN* 10 74ACT245 Samsung Electronics Schematic Diagrams Controller Diagram(7/11) SEN_5V VCC LF15 SCF451832-223T 1 3 2 5V1 R180 1K R179 1K 5V2 C193 33UF 10V nSTROBE C108 1nF R98 100 R109 R108 R120 R117 R121 R119 1K 1K 1K 1K 1K 1K R107 R110 1K 1K R118 1K J11-1 PD(0:7) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PD(0) PD(1) PD(2) PD(3) PD(4) PD(5) PD(6) PD(7) C130 C129 C128 C145 C143 C144 C146 C142 220pF 220pF 220pF 220pF 220pF 220pF 220pF 220pF U21 74F1071SCX1 C1 2 C2 3 C3 4 C4 5 C5 7 C6 8 C7 9 C8 10 C9 6 GND FGND C10 C11 C12 C13 C14 C15 C16 C17 C18 R129 5.1K nACK BUSY PERROR SELECT nAUTOFD 11 R128 5.1K R126 5.1K R125 5.1K 13 14 15 17 18 19 (CENT36) 5V2 20 33 33 33 33 33 C168 C167 C182 470pF 100pF 100pF C166 C165 470pF 470pF SEN_5V R161 1K nSELECTIN nFAULT nINIT Samsung Electronics 12 LCTL4036E09 R159 5.1K R130 R131 R127 R124 R160 5V1 16 GND SEN_5V 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 R158 33 R162 33 R163 1K R165 1K R164 C181 C183 C184 470pF 470pF 470pF 33 8-13 Schematic Diagrams Controller Diagram(8/11) VCC J6-1 1 2 3 4 J7-1 VCC VCC R122 3.3K nCMSG RA23 100 8 LSYNC 10 U15-4 9 74F14 U15-5 11 74F14 1 3 5 7 nFSYNC RDY* EVIDEO* 1 3 5 7 C153 C152 C151 470pF 1nF 8-14 C170 C169 470pF 470pF 470pF C156 C155 1nF R136 10K R137 10K R132 3.3K R134 10K R135 10K R133 10K C157 33UF 10V B12 1 2 B13 1 2 2 4 6 8 RA22 100 CCLK* nPRINT nEMSG EXITP* nEBSY R138 5.1K 2 4 6 8 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C154 C158 470pF 1nF 470pF Samsung Electronics Schematic Diagrams Controller Diagram(9/11) VCC DATA(24:31) J10-1 C14 100nF RA2 39 IOCS3 DATA(24) DATA(25) DATA(26) C17 22pF VCC R24 1K DATA(27) DATA(28) DATA(29) DATA(30) DATA(31) RD* WR* EIRQ1 RA1 39 RA3 39 1 3 5 7 2 4 6 8 1 3 5 7 2 4 6 8 1 3 5 7 2 4 6 8 B1 B2 B3 B4 ADDR(4) ADDR(5) ADDR(6) ADDR(7) C26 C27 C28 100pF 100pF 100pF 1 1 1 1 UNUSED 2 2 2 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 DHB-RB30-S13NN Samsung Electronics 8-15 Schematic Diagrams Controller Diagram(10/11) VCC VCC ADDR(2:18) DATA(16:31) RA4 39 J4-31 FX2M6A-60P-1.27DSAL 1 3 5 7 2 4 6 8 R66 10K DATA(27) DATA(26) DATA(25) DATA(24) 4 34 5 35 6 36 7 37 ADDR(6) 8 38 ADDR(10) 9 39 10 40 11 41 12 42 13 43 14 44 15 45 16 46 ADDR(5) 17 47 ADDR(4) 18 48 ADDR(3) 19 49 20 50 21 51 22 52 23 53 24 54 25 55 26 56 27 57 EIRQ2 RA9 39 ADDR(2) DATA(23) DATA(22) DATA(21) DATA(20) ADDR(17) ADDR(16) ADDR(15) ADDR(14) 1 3 5 7 2 4 6 8 ADDR(13) ADDR(12) VCC VCC R65 10K ADDR(11) DPO_RST* R20 ADDR(9) R21 0 0 IOCS2 nWAIT VCC VCC ADDR(8) U4-1 ADDR(7) 74F08 UNUSED 14 1 VCC R22 0 3 TT1 2 GND IOCS1 7 ADDR(18) R63 10 R54 10 RD* 13 WR* 11 VCC U4-4 74F08 12 10 8 C12 100nF U4-3 74F08 9 28 58 29 59 30 60 BRDIN* C24 33uF 10V 8-16 VCC R23 10K RA8 39 3 33 C25 100pF VCC 2 4 6 8 2 R64 10K 1 3 5 7 31 32 100pF DATA(31) DATA(30) DATA(29) DATA(28) 1 C64 IOCS1 2 DATA(19) 4 DATA(18) 6 DATA(17) 8 DATA(16) R67 10K RA5 39 1 3 5 7 Samsung Electronics Schematic Diagrams Controller Diagram(11/11) VCC VCC R8 10K LF2 SCF451832-223T U7 6 5 VCC1 *DACK DRQ C5 33uF C32 100nF DATA(24:31) 8 9 10 11 12 13 14 15 DATA(24) DATA(25) DATA(26) DATA(27) DATA(28) DATA(29) DATA(30) DATA(31) VCC R42 10K D0-SO D1 D2 D3 D4 D5 D6 D7 R27 0 1 20 MODE0 MODE1 19 R31 20 B6 R51 20 B8 3 B7 4 R52 18 V3.3 1 2 3 4 7 16 2 CN2-1 787780-1 D+ USBCS 1 10V D25 24 EIRQ0 ADDR(14) USB_RST* 3 22 *CS *RD *WR_SK INTR A0-ALE-SI *RESET VCC 1.5K R16 C31 C62 10uF 16V D2 DA204K 470 100nF 3 2 1 D3 DA204K 2 3 2 1 R17 0 C30 33pF C48 100pF C18 100pF 28 CLKOUT 26 XIN 27 XOUT 17 GND1 21 GND2 23 GND3 VCC USBN9602-28M U3-1 74ACT32SCX 14 1 USBCS VCC 3 U3-3 74ACT32SCX C15 2 100pF U9-2 74F04SC C3 100nF U3-4 7 74ACT32SCX U3-2 74ACT32SCX 4 8 9 4 13 10 WR* 3 ADDR(15) 11 6 12 IOCS0 C16 5 RD* 100pF Y1 MA-506,48MHz VCC U6 FS741 LF4 SCF451832-223T R9 10 3 1 2 8 C19 10uF 16V C29 150pF R48 1K R29 68 R28 1K 7 6 5 VCC VI VO GND XIN XOUT REF LF 1 2 3 4 C22 22pF R201 39 3 1 2 R200 1M R11 2K C21 100pF 4 C221 150pF C20 22pF C4 22pF B14 1uH 3216 C23 10pF Samsung Electronics 8-17 Schematic Diagrams 8-3. Panel Board SW1 J1 7 6 LED4 5 LED3 4 LED2 3 LED1 2 LED1 GREEN 1 7P LED5 GREEN PANEL LED2 AMBER LED3 AMBER LED4 RED C1 104 VCC R5 180 POWER 8-18 R1 180 READY R2 180 PAPER R3 180 MANUAL R4 180 ERROR Samsung Electronics Schematic Diagrams 8-4. Motor-SUB Board Diagram +24V +5V C1 10UF 50V NOT USED C6 330PF 50V C8 330PF 50V 5 +5V 11 +24V C2 47UF 50V 1 2 3 4 5 6 7 8 9 10 DLCON_10P MOTOR_PA 13 14 7 8 MOTOR_EA CN3 OUT1 OUT4 OUT2 OUT3 PHASE1 U1 *ENABLE1 *ENABLE2 A2918SWV PHASE2 1 2 3 4 1 17 2 4 RC1 SENSE1 E1 REFE GND E2 SENSE RC2 MOTOR_PB LOAD LOGIC CN1 C11 10NF 50V C10 10NF 50V 12 16 18 15 10 3 6 9 C9 10NF 50V SLCON4P R5 1K C7 330PF 50V R3 56K C4 820PF 50V R6 1K R2 0.33 2W +5V R1 0.33 2W C3 820PF 50V R4 56K R7 1K C5 330PF 50V R8 5.6K +24V FB1 BDCORE D7 1N4003 CN2 1 2 +5V C FAN_E SLCON2P-FAN B 2 D1 DIODE_3P 3 1 R12 5.6K 1/8 Q1 KSC1008 E +24V CN4 1 2 D8 1N4003 SLCON2P C MP_CLUTCH R9 5101/8 B R13 5.6K 1/8 2 Q2 KSC1008 E D2 DIODE_3P 3 1 +5V R11 15K 1/8 +5V R10 150 1/8 CN5 1 2 3 MP_PAPER 2 1 Samsung Electronics D3 DIODE_3P 3 SLCON3P 8-19 8-20 LD18 SR3312-V LD17 SR3312-V LD16 SR3312-V LD15 SR3312-V LD14 SR3312-V LD13 SR3312-V LD12 SR3312-V LD11 SR3312-V LD10 SR3312-V LD9 SR3312-V LD8 SR3312-V LD7 SR3312-V LD6 SR3312-V LD5 SR3312-V LD4 SR3312-V LD3 SR3312-V LD2 SR3312-V LD1 SR3312-V Schematic Diagrams 8-5. PTL Diagram VCC CN1 1 2 CONN2 Samsung Electronics Schematic DiagramsSchematic Diagrams 8-6. Localtalk diagram U6 1 U6 3 2 74LS14 5 9 6 74LS14 8 11 10 74LS14 74LS14 R3 33 U6 U6 U6 U6 4 13 12 VCC C20 0.1UF 74LS14 74LS14 VCC SCC_CS* C2 1UF U3 16 VCC C4 1UF R4 33 1 (N.A) 4 3 C5 1UF VCC 5 U1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 1 D(0) D(1) 1 2 44 3 43 4 42 5 U5 3 2 D(2) D(3) D(4) 4 5 SCC_CS* DCDA RXDA TXTA TRXCA* RTXCA* SYNCA* W_REQA* DTRA* RTSA* CTSA* 41 RD* 40 WE* 74F32 U5 6 D(5) D(6) D(7) C2- MAX232 SCC_CS* 74F32 VCC Z85230 39 A_B* 38 CE* 37 D_C* R16 10K 9 INTACK* 8 IEI 7 IEO 6 INT* 23 Y- 6 14 T1_OUT 7 T2_OUT DCDB RXDB TXTB TRXCB* RTXCB* SYNCB* W_REQB* DTRB* RTSB* CTSB* GND2 36 BEAD 2 B4 1 B3 1 B21 BEAD 2 BEAD 2 BEAD 2 B5 1 BEAD 2 C6 C9 C7 C8 330PF 330PF 330PF 330PF 22 14 16 15 13 12 11 19 20 21 24 31 29 30 32 33 34 27 26 25 VCC U7 1 2 74LS14 PCLK GND1 35 B1 1 J1 1 6 2 7 3 8 4 9 5 DESUB-9P 13 R1_IN 8 R2_IN GND 15 D0 D1 D2 D3 D4 D5 D6 D7 1K C1- 10 VCC D(0) D(1) D(2) D(3) D(4) D(5) D(6) D(7) R15 C3 1UF 12 R1_OUT 9 R2_OUT D(0:7) C1 33UF J3 2 C2+ 11 T1_IN 10 T2_IN C18 0.1UF VCC Y+ C1+ C23 330PF R5 33 C21 0.1UF U2 MAX491 C12 C13 330PF 330PF 14 J2 VCC Y 9 R7 27 R8 27 5 DI Z 10 R9 27 R10 27 A 12 R11 27 R12 27 B 11 R13 27 R14 27 B61 BEAD 2 B7 1 B81 BEAD 2 BEAD 2 4 DE CON30 3 _RE 2 RO VCC GND2 GND1 7 6 C10 C11 330PF 330PF 6 3 4 1 7 2 8 5 DIN-8P U4 2 OSC1 4 3 2 VCC CLK GND NC 1 2 3 3 PR 4 R6 33 Q D CLK C15 100PF Q_ 5 C14 100PF 6 1 1 R1 68 R2 68 CL LF1 VCC FILTER-150PF C17 0.1UF 7.3728MHZ 3 74LS74 U7 4 74LS14 VCC 5 VCC U7 6 74LS14 C19 0.1UF C16 0.1UF C22 0.1UF C24 0.1UF 9 U7 8 74LS14 11 U7 10 74LS14 13 U7 12 74LS14 Samsung Electronics 8-21