Download Texas Instruments TPS65020EVM-110 User's Manual

User's Guide
SLVU138 – August 2005
TPS65020EVM-110 User's Guide
This User’s Guide describes the characteristics, operation, and use of the
TPS65020EVM-110 evaluation module (EVM). This EVM is designed to help the user
evaluate and test the various operating modes of the TPS65020. This User’s Guide
includes setup instructions for the hardware and software, a schematic diagram, a bill
of materials (BOM), and PCB layout drawings for the evaluation module.
1
2
3
4
5
Contents
Introduction .......................................................................................... 1
Setup ................................................................................................. 2
Board Layout ........................................................................................ 3
Schematic and Bill of Materials ................................................................... 8
Related Documentation .......................................................................... 10
List of Figures
1
2
3
4
5
6
Assembly Layer .....................................................................................
Top Layer ............................................................................................
Routing, GND Plane................................................................................
Routing, VIN Plane .................................................................................
Routing, Bottom Layer .............................................................................
TPS65020EVM-110 Schematic ...................................................................
4
5
6
7
8
9
List of Tables
1
1
HPA110A BOM .................................................................................... 10
Introduction
The Texas Instruments TPS65020EVM is an integrated Power Management IC for applications that are
powered with one Li-Ion or Li-Polymer cell, and require multiple power rails. The TPS65020 contains three
highly efficient switching step-down converters, two LDOs, and additional status and I/O pins. The device
is controlled via an I2C™ interface.
1.1
Requirements
In order for this EVM to operate properly, the following components must be connected, and properly
configured.
1.2
Personal Computer (PC)
A computer with a USB port is required to operate this EVM. The TPS65020 interface software, which is
run on the PC, communicates with the EVM via the PC USB port. The user sends commands to the EVM
as well as reads the contents of the TPS65020 internal registers through the USB port.
I2C is a trademark of Philips Electronics.
SLVU138 – August 2005
TPS65020EVM-110 User's Guide
1
www.ti.com
Setup
1.3
Printed Circuit Board Assembly
The TPS65020EVM-110 PCB contains the TPS65020 IC and its required external components. This
board contains several jumpers and connectors that allow the user to customize the board for specific
operating conditions.
1.4
USB to I2C Interface Board (EV2300)
The EV2300 is the link that allows the PC and the EVM to communicate. One end of the EV2300
connects to the PC with the supplied USB cable, and the other end of the EV2300 connects to the EVM
with the supplied Molex cable. When the user writes a command to the EVM, the interface program, which
is run from the PC, sends the command to the PC USB port. The EV2300 receives the USB command
and converts the signal to an I2C protocol. It then sends the I2C signal to the TPS65020 board. When the
user reads a status register from the EVM, the PC sends a command to read a register on the EVM.
When the EVM receives the command, it reports the status of the register via the I2C interface. The
EV2300 receives the information on the I2C interface, converts it to a USB protocol, and sends it to the
PC.
1.5
Software
Texas Instruments has provided software to assist the user in evaluating this EVM. To install the software,
insert the enclosed CD into your computer. The software should start automatically. If it does not, simply
go to <Start>, <Run>, and type “D:\SLVU138.exe”, and click <OK> (assuming that D: is your CD drive).
The program should run without errors. If any problems occur that result in the program not being
installed, view the readme.txt file on the CD for further information. Check the TPS65020 product folder on
the TI website for the latest revision of the software.
2
Setup
This section describes the jumpers and connectors on the EVM as well as how to properly connect, setup,
and use the TPS65020EVM-110.
2.1
Input / Output Connector Descriptions
INPUT / OUTPUT
DESCRIPTION
J1 – VIN
Input voltage from external power supply, recommended maximum 5.5 V. Input current is dependent
on load but is typically below 2 A.
J2 – GND
This is the return connection for VI.
J3 – VINLDO/GND
Input voltage and return for LDO1 and LDO2C. Resistor R23 connects this pin to VDCDC1. If an
external power supply is used, remove R23. Recommended maximum input voltage is 5.5 V
J4 – VSYSIN/GND
Input voltage and return for VSYSIN, one of the input voltages for RTC. Resistor R24 connects this
input to VDCDC1. If an external power supply is used, remove R24. Recommended maximum input
voltage is 4 V
J5 – VBACKUP/GND
J6 – GPIO1/GPIO2
J7 – VRTC/GND
Input voltage and return for VBACKUP, one of the input voltages for RTC. There is no on board
connections to a voltage input. Recommended maximum input voltage is 4 V.
Direct connection to the GPIO1 and GPIO2 pins. For this EVM, GPIO1 is configured as a
push-button input, and GPIO2 is configured as an LED output.
Output voltage from the RTC circuit.
Four fault outputs are available on this connector:
PWRFAIL - Fault occurs when input voltage is below 3 V. Pulled up to VRTC when safe, low for fail.
J8 – Fault Outputs
INT - Fault occurs when there is a fail on an input or output voltage. It acts as a sum fail. Pulled up
to VI when safe, low for fail.
RESPWRON– Low reset signal controlled by SW2, 300 mS. Pulled up to VI normally.
LOWBAT– Fault occurs when input voltage is below 3.6 V. Pulled up to VI when safe, low for fail.
J9 – USB
J10 – VDCDC1
2
This header duplicates the signals from the J20 interface connector.
Output from DCDC1 switching regulator, maximum output current is 1.2 A, default voltage setting is
3.3 V.
TPS65020EVM-110 User's Guide
SLVU138 – August 2005
www.ti.com
Board Layout
INPUT / OUTPUT
J11 – GND
J12 – VDCDC2
J13 – GND
J14 – VLDO1
J15 – GND
J16 –VLDO2
J17 – GND
J18 – VDCDC3
Return for VDCDC1
Output from DCDC2 switching regulator, maximum output current 1 A, default voltage setting 2.5 V.
Return for VDCDC2
Output from the low drop out regulator VLDO1, maximun current out is 50 mA, default value 1.1 V.
Return for VLDO1
Output from the low drop out regulator, VLDO2 maximum current out is 50 mA, default value 1.3 V.
Return for VLDO2
Output from the switching regulator DCDC3, maximum current is 800 mA, default value 1.55 A
J19 – GND
Return for VDCDC3
J20 – USB
USB interface connector
JP1 – DEF 1
Sets voltage for DCDC1 to 3 V or 3.3 V.
JP2 – DEF 2
Sets voltage for DCDC2 to 2.5 V or 1.8 V.
JP3 – DEF 3
Sets voltage for DCDC3 to 1.55 V or 1.3 V.
JP4 – DCDC1 ON/OFF
EN for regulator DCDC1, default setting is ON.
JP5 – DCDC2 ON/OFF
EN for regulator DCDC2, default setting is ON.
JP6 – DCDC3 ON/OFF
EN for regulator DCDC3, default setting is ON.
JP7 – LDO ON/OFF
S1 – GPIO1
S2 – HOT_RST
2.2
DESCRIPTION
EN for both LDO1 and LDO2 regulators, default setting is ON.
S1 is a normally open momentary push-button switch that, when pressed, connects VI to GPIO1.
The GPIO1 input is configured on the TPS65020 as a debounced push button that drives an
ON/OFF circuit with output at GPIO2.
S2 is a normally open momentary push-button switch that, when pressed, connects the HOT_RST
input of the TPS65020 to GND generating the Hot_Reset pulse. The HOT_RST pin is externally
pulled up.
Setup
The following steps must be followed before the EVM is operated
1. Install the TPS65020EVM Software.
2. Connect input voltages and loads to the EVM.
3. Configure all EVM jumpers to factory setting.
– JP4—ON
– JP1—3.3 V
– JP3—1.55 V
– JP2—2.5 V
– JP5—ON
– JP6—ON
– JP7—ON
4. Connect the Molex cable between the EVM and the EV2300. Note that the Molex cable must connect
to the I2C connector on the EV2300.
5. Connect the USB cable between the computer and the EVM.
6. Turn on all supplies and loads.
7. Run the TPS65020EVM software.
3
Board Layout
This section provides the TPS65020EVM-110 board layout and illustrations.
SLVU138 – August 2005
TPS65020EVM-110 User's Guide
3
www.ti.com
Board Layout
3.1
Layout
Board layout is critical for all switch mode power supplies. Figure 1 through Figure 5 show the board
layout for the TPS65020EVM-110 PWB. The nodes with high switching frequencies and currents are short
and are isolated from the noise sensitive feedback circuitry. Careful attention has been given to the routing
of high frequency current loops. See to the datasheet for specific layout guidelines.
Figure 1. Assembly Layer
4
TPS65020EVM-110 User's Guide
SLVU138 – August 2005
www.ti.com
Board Layout
Figure 2. Top Layer
SLVU138 – August 2005
TPS65020EVM-110 User's Guide
5
www.ti.com
Board Layout
Figure 3. Routing, GND Plane
6
TPS65020EVM-110 User's Guide
SLVU138 – August 2005
www.ti.com
Board Layout
Figure 4. Routing, VIN Plane
SLVU138 – August 2005
TPS65020EVM-110 User's Guide
7
www.ti.com
Schematic and Bill of Materials
Figure 5. Routing, Bottom Layer
4
Schematic and Bill of Materials
This section provides the TPS65020EVM-110 schematic and bill of materials.
8
TPS65020EVM-110 User's Guide
SLVU138 – August 2005
www.ti.com
Schematic and Bill of Materials
4.1
Schematic
Figure 6. TPS65020EVM-110 Schematic
SLVU138 – August 2005
TPS65020EVM-110 User's Guide
9
www.ti.com
Related Documentation
4.2
Bill of Material
Table 1. HPA110A BOM
Count
–001
Value
Description
Size
Part No.
MFR
10 µF
Capacitor, ceramic, 10 µF, 6.3 V, X5R, 20%
0805
C2012X5R0J106K
TDK
–002
9
9
C1, C2,
C4, C9,
C10, C11,
C14, C15,
C16
4
4
C8, C12,
C13, C18
2.2 µF
Capacitor, ceramic, 2.2 µF, 6.3 V, X5R, 10%
0603
C1608X5R0J225K
TDK
4
4
C3, C6,
C7, C17
1.0 µF
Capacitor, Ceramic, 1.0 µF, 6.3 V, X5R,10%
0603
C1608X5R0J105K
TDK
1
1
C5
1500 pF Capacitor, Ceramic, 1500 pF, 50 V, X7R, 10%
0603
C1608X7R1H152K TDK
0.087 x 0.120
LN1261CAL
Panasonic
1
1
D1
Red
Diode, LED, Red, Gullwing, GW Type, 20 ma,
1.4 mcd typ
0
0
D2
Open
Diode, LED, Red, Gullwing, GW Type, 20 ma,
1.4 mcd typ.
0.087 x 0.120
17
17
J1 - J7,
J10 - J19
Header, 2-pin, 100 mil spacing, (36-pin strip)
0.100 x 2
PTC36SAAN
Sullins
1
1
J20
Header, Friction Lock Assembly, 4-pin Right
Angle
0.400 x 0.500
22-05-3041
Molex
2
2
J8, J9
Header, 4-pin, 100 mil spacing, (36-pin strip)
0.100 x 4
PTC36SAAN
Sullins
7
7
JP1 - JP7
Header, 3-pin, 100 mil spacing, (36-pin strip)
0.100 x 3
PTC36SAAN
Sullins
0
2
JP8, JP9
Header, 2-pin, 100 mil spacing, (36-pin strip)
0.100 x 2
PTC36SAAN
Sullins
0.157 x 0.157
VLCF4020T2R2N1R7
TDK
VLF4012AT2R2M1R5
TDK
2
2
L1, L2
2.2 µH
Inductor, SMT, 1.72-A, 59-milliohm
1
1
L3
2.2 µH
Inductor, SMT, 1.5-A, 87-milliohm
0.137 X 0.147
0
0
R1 - R7,
R20, R21
Open
Resistor, Chip, xx-Ohms, 1/16-W, 1%
0603
1
1
R11
10
Resistor, Chip, 10-Ohms, 1/16-W, 1%
0603
Std
Std
1
1
R12
1.20M
Resistor, Chip, 1.20M-Ohms, 1/16-W, 1%
0603
Std
Std
1
1
R13
499k
Resistor, Chip, 499k-Ohms, 1/16-W, 1%
0603
Std
Std
2
2
R18, R19
4.75k
Resistor, Chip, 4.75k-Ohms, 1/16-W, 1%
0603
Std
Std
3
3
R22, R23,
R24
0
Resistor, Chip, 0-Ohms, 1/16-W, 1%
0603
Std
Std
1
1
R8
1.0k
Resistor, Chip, 1.0k-Ohms, 1/16-W, 1%
0603
Std
Std
6
6
R9, R10,
R14, R15,
R16, R17
100k
Resistor, Chip, 100k-Ohms, 1/16-W, 1%
0603
Std
Std
0
3
R25, R26,
R27
100k
Resistor, Chip, 100k-Ohms, 1/16-W, 1%
0603
Std
Std
2
2
SW1, SW2
Switch, SPST, PB Momentary, Sealed Washable
0.245 X 0.251
KT11P2JM
C&K
U1
IC, Power Management IC for Li-Ion Powered
Systems
0.242 x 0.242
TPS65020RHA
TI
1
IC, Power Management IC for Li-Ion Powered
Systems
0.242 x 0.242
TPS65021RHA
TI
1
1
PCB, 3.65 In x 2.95 In x 0.062 In
HPA110
Any
7
9
Shunt, 100-mil, Black
929950-00
3M
1
5
Ref Des
0
0.100
Related Documentation
1. TPS65020, Power Management IC for Li-Ion Powered Systems data sheet, SLVS607
10
TPS65020EVM-110 User's Guide
SLVU138 – August 2005
FCC Warnings
This equipment is intended for use in a laboratory test environment only. It generates, uses, and
can radiate radio frequency energy and has not been tested for compliance with the limits of
computing devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide
reasonable protection against radio frequency interference. Operation of this equipment in other
environments may cause interference with radio communications, in which case the user at his
own expense will be required to take whatever measures may be required to correct this
interference.
EVM IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR
EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use. As
such, the goods being provided may not be complete in terms of required design-, marketing-,
and/or manufacturing-related protective considerations, including product safety measures typically found in the end product incorporating the goods. As a prototype, this product does not fall
within the scope of the European Union directive on electromagnetic compatibility and therefore
may not meet the technical requirements of the directive.
Should this evaluation kit not meet the specifications indicated in the EVM User's Guide, the kit
may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING
WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further,
the user indemnifies TI from all claims arising from the handling or use of the goods. Please be
aware that the products received may not be regulatory compliant or agency certified (FCC, UL,
CE, etc.). Due to the open construction of the product, it is the user's responsibility to take any
and all appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY
SHALL BE Liable to the other FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the
user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software
performance, or infringement of patents or services described herein.
Please read the EVM User's Guide and, specifically, the EVM Warnings and Restrictions notice in
the EVM User's Guide prior to handling the product. This notice contains important safety
information about temperatures and voltages. For further safety concerns, please contact the TI
application engineer.
Persons handling the product must have electronics training and observe good laboratory practice
standards.
No license is granted under any patent right or other intellectual property right of TI covering or
relating to any machine, process, or combination in which such TI products or services might be
or are used.
www.ti.com
Related Documentation
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the input voltage range of 0 V to 4 V.
Exceeding the specified input range may cause unexpected operation and/or irreversible damage
to the EVM. If there are questions concerning the input range, please contact a TI field
representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or
possible permanent damage to the EVM. Please consult the EVM User's Guide prior to
connecting any load to the EVM output. If there is uncertainty as to the load specification, please
contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than
100°C. The EVM is designed to operate properly with certain components above 100°C as long
as the input and output ranges are maintained. These components include but are not limited to
linear regulators, switching transistors, pass transistors, and current sense resistors. These types
of devices can be identified using the EVM schematic located in the EVM User's Guide. When
placing measurement probes near these devices during operation, please be aware that these
devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2005, Texas Instruments Incorporated
12
TPS65020EVM-110 User's Guide
SLVU138 – August 2005
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated