Download Philips DVDR3512V/12 User's Manual
Transcript
3 DVDR3510V DVDR3512V DVD Recorder / VCR Enjoy Start playback A From a disc Start recording A Record to DVD or VCR A Press DVD on the remote control. B Press OPEN/CLOSE Z, load a disc and close the disc A Press DVD to record to a recordable DVD. Quick Start Guide OR, press VCR to record to a VHS tape. B Load in a blank recordable DVD to the disc tray or a tray. VHS tape to the tape deck. C Press PLAY/PAUSE u to start playback. D To stop playback, press STOP x. C Press SOURCE repeatedly to select the source to B z To record a TV programme, use P+/- on the remote control to select a programme channel. record from (eg, TUNER, CAM1, DV, EXT1 or EXT2). From a VHS tape D Press REC MODE repeatedly to select a desired A Press VCR on the remote control. B Insert a pre-record VHS tape into the tape deck. recording mode (refer to the Record Mode table). E Press REC z to start recording. Press REW m to rewind the tape if necessary to the beginning of the recording. 1 2 3 Note To set the recording time, press REC z repeatedly to extend the recording time in 30 minute increments. The recording will stop automatically at the designated end time. C Press PLAY/PAUSE u to start playback. D To stop playback, press STOP x. z To record from an external device, press PLAY on the device to start playback. F To stop the recording, press STOP x. B Connect Set up Enjoy Dubbing (VCR î DVD) A Press VCR to dub from VCR to DVD. OR, press DVD to dub from DVD to VCR. What’s in the box? B Load in a blank recordable DVD to the disc tray or a VCR VHS tape to the tape deck. DVD C Press DIRECT DUBBING. SOURCE Dubbing to DVD Remaining Time Rec. Mode PLAY/PAUSE OK 01:54 SP Cancel OK DVD Recorder / VCR D Select the desired recording mode, then move to Remote Control and 2 batteries in the menu and press OK on the remote control to start dubbing. OK E To stop the dubbing, press STOP x. REC MODE User Manual Need help? User Manual See the user manual that came with your Philips recorder. Online Go to www.philips.com/support. RF Coaxial Cable 2007 © Koninklijke Philips N.V. All rights reserved. 12 NC 3139 245 26222 DVDR3510V_qsg_eng_26222.indd 1 2007-07-26 4:53:58 PM 1 2 Connect Set up Basic Connection A Before Connecting A Press STANDBY-ON on the recorder. B Turn on the TV and other connected devices (e.g. Select one of the following basic connections ( A or B ) according to the type of connecting devices you have. D Setup and install TV channels. Highlight and press right X. Select { Channel Search } and press OK to start automatic TV channel search. Cable Box, Satellite Receiver). If your TV is currently connected to a VCR, you have to unplug all the connections from your VCR and TV. Your new Philips Recorder replaces the VCR for your recording needs. C If your TV does not switch to the correct viewing channel, press the Channel Down button (or AV, SELECT, ° button) on the TV’s remote control repeatedly until you see the blue DVD background screen. This is the correct viewing channel for the recorder. Television ( rear) Television ( rear) Finding the viewing channel Setup - Channel Setup Channel Search Search Modify Channel Information Edit Sort Channels Sort SCART IN From an offair antenna wall socket or cable box Note This process may take several minutes. Once complete, the total number of channels found and stored appears on the TV. SCART IN E Set the date and time. VIDEO (CVBS) EXT 2 AUX - I/O Y S-VIDEO (Y/C) PB L AUDIO PR R TV EXT 1 TO TV - I/O AUDIO / VIDEO OUT COMPONENT AUDIO OUT VIDEO OUT COAXIAL Philips Recorder (rear) DIGITAL AUDIO OUT B 3139 241 26501 MAINS ANTENNA VIDEO (CVBS) EXT 2 AUX - I/O L PB AUDIO R TV EXT 1 TO TV - I/O AUDIO / VIDEO OUT PR COMPONENT AUDIO OUT VIDEO OUT Start basic setup Use the recorder’s remote control and follow the onscreen instructions to complete the installation. Y S-VIDEO (Y/C) Highlight and press right X. Select { Date (dd/mm/yy) } or { Time (hh:mm:ss) } and press OK. Use the numeric keypad 0-9 to input the date/time, then press OK to confirm. MAINS ANTENNA COAXIAL DIGITAL AUDIO OUT Philips Recorder (rear) Cable Box (rear) A Press SETUP on the remote control. Setup - General From an off-air antenna wall socket Option A Option B Use this connection if you are connecting the antenna cable directly from the antenna wall socket or from a Cable Box without a Scart output socket. Use this connection if your current antenna cable is connecting through a Cable Box with Scart output socket. A Unplug the antenna cable that is currently connected A Keep the existing antenna connection from the Cable to your TV and plug in the antenna cable to the ANTENNA socket on this recorder. B Connect the supplied RF coaxial cable from the TV socket on this recorder to the Antenna In socket on the TV. C Connect a scart cable (not supplied) from the EXT1 TO TV-I/O socket on this recorder to the Scart input socket on your TV. D Plug in the power cable from the recorder to an AC box to your TV. B Connect a scart cable (not supplied) from the EXT1 TO TV-I/O socket on this recorder to the Scart input socket on your TV. C Connect another scart cable from the EXT2 AUXI/O socket on this recorder to the Scart output socket on the Cable Box. D Plug in the power cable from the recorder to an AC power outlet. power outlet. Note See the accompanying user manual for other possible connections (e.g. Composite Video, Component Video, S-VIDEO). DVDR3510V_qsg_eng_26222.indd 2 Screen Saver Date (dd / mm / yy) 01/01/07 Time (hh : mm : ss) 0 0 :0 1 :0 8 Date - Time Setting Auto Date - Time Preset P001/Ch003 Show DivX® Registration Code OK On Country Germany Video Output Selection SCART RGB Restore Factory Settings Setup - Clock OK Note The settings will be updated according to the broadcast channel information of preset Programme Number 1. F Press SETUP to exit. Note Use up S and down T keys to toggle through the options. Select an item by pressing right X. To confirm a setting, press OK. B Select the country of your residence. Highlight and press right X. Select { Country } and press OK to confirm your selection. C Select the recorder’s menu display language. Highlight and press right X. Select { On Screen Display Language } and press right X. Select the desired language option and press OK to confirm your selection. 2007-07-26 4:53:59 PM