Download Fujitsu Siemens Computers Primergy RX220 User's Manual
Transcript
PRIMERGY RX220 System configurator and order-information guide January 2006 Contents Instructions Configuration diagram Configurator 0 System software I Basic unit II Processor III Memory IV Graphics V Accessible drives VI Hard disk drives VII SCSI controller VIII Fibre-Channel controller IX Disk array X Communication/Network XI System Management Products (RemoteView) XII Miscellaneous XIII Country specific power cord Change report PRIMERGY Server System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 Instructions This document contains basic product and configuration information that will enable you to configure your system via PC-/System-Architect Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system. You can configure your individual PRIMERGY server in order to adjust your specific requirements. The System configurator is divided into several chapters that are identical to the current price list and PC-/System-Architect. Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom. Section III Memory, example There are X memory slots which can be equipped with XXX MB It is permissible to make up to X passes through the memory upgrade options S26361-XXX-XXX Memory XXX MB S26361-XXX-XXX Memory XXX MB max. X times per system max. X times per system X times In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x Please note that there are information symbols which indicate necessary information. Further information in the internet see: http://www.primergy.com (internet) http://extranet.fujitsu-siemens.com/primergy (extranet) Prices and availability see price list and PC-/System-Architect. Subject to change and errors excepted. Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 2 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 Configuration diagram PRIMERGY RX220 System unit ( I ) Bank I (2 Modules) Opteron 2xx Bank II Standard (2 Modules) Power supply Bank III (2 Modules) Opteron 2xx Bank IV (2 Modules) 5.25"x0.5" Empty/CD/ DVD-ROM Memory ( III ) Processor ( II ) Note: Memory is directly connected to the CPU. So, if only one CPU is configured only 2 banks are possible. Extension slots SCSI Controller ( VII ) Disk Array ( IX ) Communication/Network ( X ) System Management ( XI ) Miscellaneous ( XIII ) Accessible drives ( V ) Hard disk drives ( VI ) 3.5"x1" id-0 Slot 1: PCI-X 64 Bit / 133 MHz, Standard - long 3.5"x1" id-1 Slot 2: PCI-Express x8, Standard - short Key: Included in basic unit Option Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 3 of 15 PRIMERGY-Software Configurators and Release Lists PRIMERGY RX220 Status 2005-12-20 Start PRIMERGY RX220 SW - Configurator 32 bit with OEM-Software for PRIMERGY Server without OEM-Software for PRIMERGY Server Usage of OEM SW from MS is not possible under ESX or GSX Later use of OEM operating system software is not allowed, apart from few VMware add-ons VMware-Software - VCMS VirtualCenter Management Server - GSX Server and GSX Virtual Infrastructure Node - P2V Assistant Enterprise Edition For all SW products please refer to the corresponding software configurator accessible via the Extranet under Configuration & Tools, -All configurations, -Software, URL see below. Microsoft - Software: W - Windows Server 2003, Web Edition (only English) Standard Edition Enterprise Edition - Additional loose Client-Access-Licenses (CALs) (not for Web Edition) Linux - Software: L **) - SuSE Linux Enterprise Server - Red Hat Enterprise Linux CITRIX-Software for Windows: W-MF - Presentation Server LoadBalancing Additional User Licences Adaptive Services Control Center (ASCC)*) ASCC Satellite Node SLES, RHEL, W2K3 Manageability Software: V**) - RemoteView Software - RemoteView Service Board - RemoteView Diagnosis - RemoteDeploy - vPMS 2005std - Altiris Server Deployment Details eg. version numbers are published on the page referred to *) Pay attention to the ASCC release and ordering information in the Extranet under http://extranet.fujitsu-siemens.com/ascc **) Pay attention to release and order information in PRINCE -> Operating System Backup-Software / Application-Software: U - ARCserve - openSM2 http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses: for internal users: http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm for partners: http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm Continue with PRIMERGY HW configurator Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 4 of 15 PRIMERGY-Software Configurators and Release Lists PRIMERGY RX220 Status 2005-12-20 Start PRIMERGY RX220 SW - Configurator EM64T with OEM-Software for PRIMERGY Server without OEM-Software for PRIMERGY Server For all SW products please refer to the corresponding software configurator accessible via the Extranet under "Configuration & Tools, -All configurations, -Software, URL see below. only EM64T Microsoft - Software: W - Windows Server 2003, x64 Standard Edition x64 Enterprise Edition - Additional loose Client-Access-Licenses (CALs) only Later use of OEM operating system software is not allowed. Linux - Software: L *) **) only - SuSE Linux Enterprise Server EM64T - Red Hat Enterprise Linux VMware GSX Server EM64T and GSX Virtual Infrastructure Node Manageability Software: V**) only - RemoteView Software EM64T - RemoteView Service Board - RemoteView Diagnosis Details eg. version numbers are published on the page referred to *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under http://extranet.fujitsu-siemens.com/primecluster **) Pay attention to release and order information in PRINCE -> Operating System http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses: for internal users: http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm for partners: http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm Continue with PRIMERGY HW configurator Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 5 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 Start PRIMERGY RX220 I Section Basic unit System unit consisting of: * 1U Housing including standard power supply * Fans - Fans for Power Supply and Chassis * Drives / Bays - 2 bays 1" for SATA hot-plug or "easy change" HD - 1 bay (for accessible drives) with - 1 IDE-CD- or DVD- or CD-RW-ROM 0,5" height Systemboard with: - Dual Processor Board with Opteron 940 pin socket (s. section II) - 8 memory slots (s. section III) - SATA RAID controller on-board (s. section IX) - Dual LAN on-board 10/100/1000TX (s. section X) - Graphics controller (s. section IV) - 2 PCI Slots: 1x PCI-X 64 Bit / 133 MHz standard long 1x PCI-Express x8 standard short 1xx mm - BMC (Baseboard Management Controller) Servermanagement Chip on board External Interfaces: - 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared) - 1x keyboard (PS/2) - 1x mouse (PS/2) - 1x VGA (15 pins) - 4x USB 2.0 (2x front and 2x rear) - 2x LAN RJ45 Cables: 1. IDE cable for CD/DVD. 2. SATA cables for up to 2 internal HDDs 3. Power cable Software: - ServerStart packet incl. ServerBooks CD, ServerSupport CD and ServerView - Documentation engl. (multilingual on CD) Mounting kit for PRIMERGY RX220 is part of the basic unit - 1 pair of telescopic rails (650 - 790mm) - 1 bracket DC-PC-Rack Mounting kit for mounting of servers in in FSC 19" PRIMECENTER- racks and all server racks conforming to EIA standard EIA-310-D for 19" racks. Therefore the mounting kit is variable in depth from 650 - 790mm Cables included in basic unit Connections Cable PRIMERGY RX220 1. IDE CD/DVD ¡ ¡ 2. SATA cables HDDs ¥ ¥ 3. Power cable A Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 6 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 A All Basic units include a pair of identical Memory Modules. Maximum Memory expendability depends on chosen base unit! 1U Rack server for 19'' racks 1U Rack server for 19'' racks Basic unit with: - 1x Opteron ( 1MB SLC ) single core processor Basic unit with: - 1x Opteron ( 2x 1MB SLC ) dual core processor Opteron 244 (1.80 GHz) Opteron 265 (1.8 GHz) Opteron 265 2x 1MB 1GB Opteron 265 2x 1MB 2GB Opteron 265 2x 1MB 4GB S26361-K986-V211 S26361-K986-V212 S26361-K986-V214 Opteron 270 (2.0 GHz) Opteron 270 2x 1MB 1GB Opteron 270 2x 1MB 2GB Opteron 270 2x 1MB 4GB S26361-K986-V221 S26361-K986-V222 S26361-K986-V224 Opteron 275 (2.2 GHz) Opteron 275 2x 1MB 1GB Opteron 275 2x 1MB 2GB Opteron 275 2x 1MB 4GB S26361-K986-V231 S26361-K986-V232 S26361-K986-V234 Opteron 244 1MB 1GB Opteron 244 1MB 2GB Opteron 244 1MB 4GB Opteron 246 (2.00 GHz) S26361-K986-V121 S26361-K986-V122 S26361-K986-V124 Opteron 246 1MB 1GB Opteron 246 1MB 2GB Opteron 246 1MB 4GB Opteron 248 (2.20 GHz) S26361-K986-V131 S26361-K986-V132 S26361-K986-V134 Opteron 248 1MB 1GB Opteron 248 1MB 2GB Opteron 248 1MB 4GB Opteron 250 (2.40 GHz) S26361-K986-V141 S26361-K986-V142 S26361-K986-V144 Opteron 250 1MB 1GB Opteron 250 1MB 2GB Opteron 250 1MB 4GB Opteron 252 (2.60 GHz) S26361-K986-V151 S26361-K986-V152 S26361-K986-V154 Opteron 252 1MB 1GB Opteron 252 1MB 2GB Opteron 252 1MB 4GB Opteron 254 (2.80 GHz) S26361-K986-V161 S26361-K986-V162 S26361-K986-V164 Opteron 254 1MB 1GB Opteron 254 1MB 2GB Opteron 254 1MB 4GB S26361-K986-V171 S26361-K986-V172 S26361-K986-V174 PRIMERGY Rack S26361-F1647-E302 Installation ex works for one server or subsystem. Hereby the rack will be delivered completely pre-mounted and all wired connections are tested. With racks 12U, 24U, 38U: Systems and components will be delivered installed in the rack With racks 46U: Systems and components will be delivered separately To be ordered only together with a PRIMERGY PRIMECENTER rack e.g.: S26361-K826-V10x refer configurator PC-Rack max. 1x per System S26361-F1331-L200 Mounting kit for PRIMERGY19" Classic rack RMK CR RX220 complete for mounting in PRIMERGY Classic racks It is necessary to leave one height unit between each server in order to arrange the cables. Restrictions from the Inform: prim_racks_0603 are to be fulfilled. "Rack-mounting ex factory" This service is to be ordered once per installable server/storage subsystem, in order to get the server/storage subsystem mounted into the PRIMERGY racks. In case of the 46 U PRIMERGY Rack, this service has to be ordered, to get the mounting kits and the cables installed. B Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 7 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 B II Section Processor There are 2 processor 940 pin sockets available. One CPU is included in each basic unit. It is also possible to upgrade a dual-processor system later on. Two processors with different clock frequencies or different caches are not possible. A multi-processor operating system is required for a dual-processor system. 2nd. CPU III Section S26361-F3167-E244 Opteron 244 with 1.8 GHz with 1MB SLC on Chip (SLC=Second Level Cache) and passive heat sink occupies CPU socket max. 1x per system S26361-F3167-E246 Opteron 246 with 2.0 GHz with 1MB SLC on Chip (SLC=Second Level Cache) and passive heat sink occupies CPU socket max. 1x per system S26361-F3167-E248 Opteron 248 with 2.2 GHz with 1MB SLC on Chip (SLC=Second Level Cache) and passive heat sink occupies CPU socket max. 1x per system S26361-F3167-E250 Opteron 250 with 2.4 GHz with 1MB SLC on Chip (SLC=Second Level Cache) and passive heat sink occupies CPU socket max. 1x per system S26361-F3167-E252 Opteron 252 with 2.6 GHz with 1MB SLC on Chip (SLC=Second Level Cache) and passive heat sink occupies CPU socket max. 1x per system S26361-F3167-E254 Opteron 254 with 2.8 GHz with 1MB SLC on Chip (SLC=Second Level Cache) and passive heat sink occupies CPU socket max. 1x per system S26361-F3167-E265 Opteron 265 with 1.8 GHz with 2x 1MB SLC on Chip (SLC=Second Level Cache) and passive heat sink occupies CPU socket max. 1x per system S26361-F3167-E270 Opteron 270 with 2.0 GHz with 2x 1MB SLC on Chip (SLC=Second Level Cache) and passive heat sink occupies CPU socket max. 1x per system S26361-F3167-E275 Opteron 275 with 2.2 GHz with 2x 1MB SLC on Chip (SLC=Second Level Cache) and passive heat sink occupies CPU socket max. 1x per system Memory There are 8 memory slots available (4 banks, each bank consists of two slots => 2 modules per bank are necessary). They can optionally be equipped with 512MB, 1GB, 2GB (or 4GB if available) registered DDR 400 PC3200 SDRAM modules. In every basic unit the first memory bank is already equipped with either 1GB, 2GB or 4GB memory, so the memory extensions can still be configured up to three times for the second, third and fourth memory bank. Note: Memory is directly connected to the CPU. So, if only one CPU is configured only 4 modules are possible. Then 1x memory extension can be ordered. For a Dual CPU configuration 3x memory extension can be ordered. Maximum configurable memory extension is 16 GB (or 28GB when 4 GB modules are available), depending on basic unit. ECC with memory scrubbing and Chipkill is standard for RX220. S26361-F3166-E521 Main memory 1GB PC3200 registered DDR RAM consisting of two modules occupies 2 slots / 1 bank max. 1x or 3x per system S26361-F3166-E522 Main memory 2GB PC3200 registered DDR RAM consisting of two modules occupies 2 slots / 1 bank max. 1x or 3x per system S26361-F3166-E523 Main memory 4GB PC3200 registered DDR RAM consisting of two modules occupies 2 slots / 1 bank max. 1x or 3x per system as soon as available S26361-F3166-E524 Main memory 8GB PC3200 registered DDR RAM consisting of two modules occupies 2 slots / 1 bank max. 1x or 3x per system 1x or 3x IV Section Graphics Graphics controller on-board (ATI Radeon, 16MB) C Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 8 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 C V Section Accessible drives Setup RX220 by ServerStart is supported with following configurations: no Floppy, no DVD, no CD: remote installation only ( PXE service & DHCP server required) built in CD/DVD or USB CD/DVD, no Floppy disk drive: UNC Network share reachable or USB Floppy connected USB Floppy, no CD/DVD: USB CD/DVD connected One of the following USB devices must be used for integrating the drivers during installation process if no automized (e.g. Serverstart / Altiris / RIS / ADS / …) installation is done: S26391-F3152-L200 1) USB DVD-ROM: (USB cable included) Traveller III DVD-ROM drive S26391-F3152-L300 2) USB DVD+-RW: (USB cable included) Traveller III DVD DL super multi drive S26391-F264-L226 3) FDD USB (external): (USB cable included) external USB FDD S26381-K340-V120 4) USB Keyboard: KBPC PX D, professional keyboard S26381-K403-L100 5) USB Mouse: Optical Wheel Mouse 6) USB Memorybird: Memorybird 256 MB S26391-F6046-L256 S26391-F6046-L24 Memorybird 1GB SNP:SY-F2313E1-P CD-ROM 0,5" 24xATAPI Connector: LD50 incl. description (Ger/US) 0.5" * 5.25", anthracite bezel max. 1x per system VI Section S26361-F3123-E1 CD-RW / DVD drive 0.5" 24/24/24x / 8x ATAPI only W2K, W3K and Linux 0.5 x 5.25", anthracite bezel max. 1x per system S26361-F3236-E1 DVD-RW 8x super multi drive all formats, DUAL/DL, DVD-RAM only W2K, W3K and Linux 0.5 x 5.25", anthracite bezel max. 1x per system Hard disk drives Every base unit is prepared for easy change SATA standard hard disks. An option for hot plug hard disks is possible to order. S26361-F3219-E80 Hard disk 80GB SATA standard 7.200 rpm, <9,0 ms, 8MB Cache SATA 3Gb/s easy change occupies 1" bay S26361-F3219-E160 Hard disk 160GB SATA standard 7.200 rpm, <9,0 ms, 8MB Cache SATA 3Gb/s easy change occupies 1" bay S26361-F3219-E250 Hard disk 250GB SATA standard 7.200 rpm, <9,0 ms, 8MB Cache SATA 3Gb/s easy change occupies 1" bay S26361-F3199-E1 Upgrade kit hot-plug hard disks including SATA backplane max. 1x per system max. 2x per system max. 2x per system max. 2x per system S26361-F3218-E80 Hard disk 80GB 7200rpm,<9.0 ms, 8MB Cache SATA 3Gb/s hot plug/hot replace tray occupies 1" bay S26361-F3218-E160 Hard disk 160GB 7200rpm,<9.0 ms, 8MB Cache SATA 3Gb/s hot plug/hot replace tray occupies 1" bay S26361-F3218-E250 Hard disk 250GB 7200rpm,<9.0 ms, 8MB Cache SATA 3Gb/s hot plug/hot replace tray occupies 1" bay max. 2x per system max. 2x per system max. 2x per system max. 2x D Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 9 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 D E PCI-X 133 MHz slot long PCI-Express x8 slot short only 1x per System only 1x per System VII Section SCSI-Controller SCSI-controller for external drives and peripheral devices S26361-F2399-E1 SCSI U160 controller Adaptec SCSI Card 29160 1 channel: LVD + Fast/ Ultra (decoupl.) LVD connect. for HD, without cable Fast/Ultra connect. for acc. drives 64/66 PCI, min 180 mm int: Fast 50 pol oder Ultra HD68 + LVD HD68; ext: HD68(LVD) SW: max. 1x per system Only released for SX10. All contr. for the connection of external storage systems are delivered without cables. For the configuration of external cabling see configurator of external storage systems. E F Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 10 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 F G PCI-X 133 MHz slot long PCI-Express x8 slot short only 1x per System only 1x per System VIII Section Fibre-Channel Controller No mix and match for Qlogic and Emulex Fibre Channel Controllers possible. With Qlogic Controller H With Emulex Controller as soon as available S26361-F3141-E10 2GBit/s FC Controller Emulex LP1050, full height bracket 1 channel 2GBit/sec FC controller LC Interface for 50um Fiber PCI-X 64Bit / 133MHz, 170mm 3.3V / 5V tolerant signaling max. 1x per system max. 1x S26361-F3141-E1 2GBit/s FC Controller Emulex LP1050Ex 1 channel 2GBit/sec FC controller LC Interface for 50um fiber PCI-Express x4, 170mm max. 1x per system All controllers for the connection of external storage systems are delivered without cables. For the configuration of external cabling see the configurator for external storage systems. For Fibre Channel SAN also other componets like switches, SFPs and optical wires are orderable (for details see price liste) G J H I With Qlogic Controller S26361-F3097-E1 2GBit/s FC Controller Qlogic QLA2340 1 channel 2GBit/sec FC controller LC Interface for 50um fiber PCI-X 64Bit / 133MHz, 170mm 3.3V / 5V tolerant signaling max. 1x per system All controllers for the connection of external storage systems are delivered without cables. For the configuration of external cabling see the configurator for external storage systems. For Fibre Channel SAN also other componets like switches, SFPs and optical wires are orderable (for details see price liste) I J Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 11 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 K J PCI-X 133 MHz slot long PCI-Express x8 slot short only 1x per System only 1x per System IX Sections Disk Array On board SATA RAID Controller RAID 0, 1 Promise PDC20319u 2-channel SATA 150 RAID Controller max. 150MB/s, with cable 32/66 PCI int.: 2 x SATA 150 SW: 2-channel Ultra 320 SCSI controller for Disk Array S26361-F3006-E128 2-channel RAID Controller U320 LSI 320-2 128MB SDRAM ECC Cache default with TBBU plug: internal 2x HD68; external: 2x VHDCI without cable 64/66 PCI controller, 180mm 3.3V and 5V tolerant signaling max. 1x per system S26361-F3090-E256 2-channel RAID Controller U320 LSI 320-2x 256MB SDRAM ECC Cache default with TBBU plug: internal 2x HD68; external: 2x VHDCI without cable 64/133 PCI-X controller, 180mm 3.3V and 5V tolerant signaling max. 1 x per system K Attention 2-channel RAID Controller only usable for external HDDs (SX30) L Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 12 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 L M X Section Communication / Network Communication / Network Low Profile Dual Gigabit Ethernet Contr. Teaming: Failover, Load Balancing onboard The Intel LAN Controllers 10/100TX. 1000SX , 1000TX Broadcom can be used with the on-board controller in Teaming Mode. ext: 2x RJ 45 connector PCI-X 133 MHz slot long PCI-Express x8 slot short only 1x per System only 1x per System A) Adapters with Teaming capability 10-1000TX /SX S26361-F3142-E1 Gigabit Ethernet Contr. 1000TX Intel Pro/1000 MT Adapter PCI 32 (33/66MHz), min 122 mm S26361-F3143-E1 Gigabit Ethernet Contr. dual 1000TX Eth. Ctrl 2x1Gbit PCIe PRO/1000P Cu Intel Pro/1000P dual Server Adapter Adapter Teaming Support PCIe x4, 170mm ext: for RJ45-plug, Cat 5 connection with Cat 5 cabling SW: VLAN, Fast & Gbit Etherchannel max. 1x per system ext: for RJ45-plug, Cat 5 connection with Cat 5 cabling SW: VLAN, Fast Etherchannel max. 1x per system S26361-F3054-E1 Gigabit Ethernet Contr. 1000SX Eth. Ctrl 1x1Gbit PCI-X Pro/1000MF LC Intel PRO/1000 MF Server Adapter Adapter Teaming Support PCI-X (PCI64/133), min 165 mm ext:LC-connector SW: VLAN, Fast Etherchannel max. 1x per system max. 2x Gigabit Ethernet cards S26361-F3053-E1 Gigabit Ethernet Contr. 1000TX Eth. Ctrl 1x1Gbit PCI-X Pro/1000MT Cu Intel PRO/1000 MT Server Adapter Adapter Teaming Support PCI-X (PCI64/133), min 165 mm ext: for RJ45-connector, Cat 5 connection with Cat 5 cabling SW: VLAN, Fast & Gbit Etherchannel max. 1x per system while stocks last S26361-F3011-E1 Gigabit Ethernet Contr dual 1000TX Eth. Ctrl 2x1Gbit PCI-X PRO/1000MT Cu Intel Pro/1000MT dual Server Adapter Adapter Teaming Support PCI-X (PCI64/66), min 163 mm ext: for RJ45-plug, Cat 5 connection with Cat 5 cabling SW: VLAN, Fast & Gbit Etherchannel max. 1x per system S26361-F3227-E1 Gigabit Ethernet Contr dual 1000TX Eth. Ctrl 2x1Gbit PCI-X PRO/1000GT Cu Intel Pro/1000GT dual Server Adapter PCI-X (PCI64/133) ext: for RJ45-plug, Cat 5 max. 1x per system M N Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 13 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 N Section XI System Management Products (RemoteView) S26361-F1790-E221 S26361-F2425-E103 RemoteView Software V5.0 RSB S2 LP 3HU Installation and configuration of RemoteView Service Board S2 RemoteView Web and LAN FrontEnd Low Profile Version with 3 U bracket RSB, BMC-Manager, RTDS and FreeDOS for one standard PCI-slot Online manuals incl. cables and RV SW max. 1x per system S26361-F2425-E305 RSB S2 LP external power supply RemoteView Service Board S2 low profile external power supply including power cable with Euro- and Euro socket connector Section XIII Miscellaneous S26361-F1652-L4 In connection with rack configurations Modem external 56kbps (V.90) the install variant of the modem MultiTech (S26361-F1652-E4) has to be ordered MT5643ZBA-Global (see rack configurator) international approval incl. 2m Telephon cord RJ11/RJ11 Adapter Plug RJ11/TAE Serial Interface cable DB25m / DB9f AC-Adapter w. German Power Cord occupies one COM port max. 1x per system Section XIV Country specific power cord Options and other peripherals For other options, refer to separate "Product specific options" These options are supplied lose with the shipment For suitable peripherals for this product, please refer to the section "Peripherals/communication" Country specific power cords are not required for rack versions, except for USA&Canada. Power cords are shipped in a rack version with inlet connector for non-heating apparatus. Description in englisch. Both included in basic unit. (1x with Standard PSU, 2x with hot plug upgrade) T26139-Y1742-E10 USA, Canada For shipments to USA&Canada, you have to order one power cord (1,8m, grey) per power supply. End PRIMERGY RX220 Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 14 of 15 System configurator and order-information guide PRIMERGY RX220 Status 2005-12-20 Change Report Date Order number Changes 2005-12-15 2005-12-12 2005-12-12 2005-10-21 S26361-F3227-E1 S26361-F1790-E221 S26361-F1790-E220 Gigabit Ethernet Controller dual 1000TX - now available RemoteView Software V5.0 - now available RemoteView Software V4.0 - no longer available First release Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 15 of 15