Download Cisco Catalyst 6500 48-Port 10/100 Upgradable to Voice, RJ-21

CH A P T E R
2
Ethernet Switching Modules
This chapter describes the 10BASE, 10/100BASE, 10/100/1000BASE, 1-Gigabit, and the 10-Gigabit
Ethernet modules and contains these sections:
Note
•
10 and 10/100 Fiber-Based Ethernet Modules, page 2-1
•
10/100 and 10/100/1000 Ethernet Modules, page 2-10
•
1-Gigabit Ethernet Modules, page 2-49
•
10-Gigabit Ethernet Modules, page 2-66
Service modules are not covered in this document. They have their own standalone documentation sets.
10 and 10/100 Fiber-Based Ethernet Modules
This section describes the following 10 and 10/100 fiber-based Ethernet modules:
•
WS-X6024-10FL-MT Ethernet Module, page 2-2
•
WS-X6148-FE-SFP Ethernet Module, page 2-4
•
WS-X6324-100FX-MM and WS-X6324-100FX-SM Ethernet Modules, page 2-6
•
WS-X6524-100FX-MM Ethernet Module, page 2-8
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-1
Chapter 2
Ethernet Switching Modules
10 and 10/100 Fiber-Based Ethernet Modules
WS-X6024-10FL-MT Ethernet Module
The WS-X6024-10FL-MT Ethernet module (Figure 2-1) provides 24 10-Mbps full- or half-duplex ports.
Table 2-1 lists the module features, and Table 2-2 lists the module physical and environmental
specifications.
Figure 2-1
WS-X6024-10FL-MT Ethernet Module Front Panel
Table 2-1
26947
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
24 PORT 10FL
LIN
K
ST
AT
US
WS-X6024-10FL-MT
WS-X6024-10FL-MT Ethernet Module Features
Feature
Description
Ports per module
24
Connector type
MT-RJ
Cabling distance
1.24 mi (2 km) full- or half-duplex over 62.5- and 125-micron MMF
Speed
10-Mbps
Buffer size
64 KB per port
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported by the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
•
Tx—2q2t
•
Rx—1q4t
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
Single connection into the 32-Gbps shared bus
Module upgrades available
PoE support
Not available.
Distributed forwarding
support
Not available.
Pluggable transceivers
support
Not supported.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-2
OL-6265-02
Chapter 2
Ethernet Switching Modules
10 and 10/100 Fiber-Based Ethernet Modules
Table 2-1
WS-X6024-10FL-MT Ethernet Module Features (continued)
Feature
Description
Digital Optical Monitoring
(DOM) support
Not supported
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Note
•
Table 2-2
Off—The port is not active or the link is not connected.
WS-X6024-10FL-MT Ethernet Module Physical and Environmental Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
7.0 lb (3.18 kg)
Power requirement
(at 42 VDC)
1.52 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-3
Chapter 2
Ethernet Switching Modules
10 and 10/100 Fiber-Based Ethernet Modules
WS-X6148-FE-SFP Ethernet Module
The WS-X6148-FE-SFP Ethernet module (Figure 2-2) provides 48 100-Mbps full- or half-duplex ports.
Table 2-3 lists the module features, and Table 2-4 lists the module physical and environmental
specifications.
Figure 2-2
WS-X6148-FE-SFP
WS-X6148-FE-SP Ethernet Module Front Panel
STATUS
1
2
3
4
5
6
7
8
9
Table 2-3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
184591
48 PORT 100BASE-X MODULE
WS-X6148-FE-SFP Features
Feature
Description
Ports per module
48
Connector type
LC or RJ-45 (depending on the type of 100-Mbps Fast Ethernet SFP
transceiver installed)
Cabling distance
Depends on the 100BASE-X Fast Ethernet SFP transceiver installed in
the module port. Refer to Appendix B for descriptions of the Fast
Ethernet SFP transceiver types and supported cabling distances.
Speed
100 Mbps
Buffer size
256 MB shared between 48 ports (5.4 MB per port)
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
•
Tx—1p3q8t (per port)
•
Rx—1p1q2t (per group of 8 ports)
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
Single connection into the 32-Gbps shared bus
Module upgrades available
PoE support
Not available.
Distributed forwarding
support
Not available.
Pluggable transceivers
support
The module supports 100BASE-X Fast Ethernet SFP transceivers.
Refer to your software release notes to determine which Fast Ethernet
SFP transceivers are supported. See Appendix B for additional
information on the Fast Ethernet SFP transceivers.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-4
OL-6265-02
Chapter 2
Ethernet Switching Modules
10 and 10/100 Fiber-Based Ethernet Modules
Table 2-3
WS-X6148-FE-SFP Features (continued)
Feature
Description
Digital Optical Monitoring
(DOM) support
Not supported
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Note
•
Table 2-4
Off—The port is not active or the link is not connected.
WS-X6148-FE-SFP Physical and Environmental Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in
the chassis.
Weight
6.6 lb (3 kg)
Power requirement
(at 42 VDC)
2.3 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to
3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-5
Chapter 2
Ethernet Switching Modules
10 and 10/100 Fiber-Based Ethernet Modules
WS-X6324-100FX-MM and WS-X6324-100FX-SM Ethernet Modules
The WS-X6324-100FX-MM and the WS-X6324-100FX-SM Ethernet modules (Figure 2-3) provide 24
100-Mbps full- or half-duplex ports. The WS-X6324-100FX-MM Ethernet module operates over
multimode fiber-optic (MMF) cable and the WS-X6324-100FX-SM Ethernet module operates over
G.652 single-mode fiber-optic (SMF) cable. Table 2-5 lists both modules features, and Table 2-6 lists
both modules physical and environmental specifications.
Figure 2-3
WS-X6324-100FX-MM and WS-X6324-100FX-SM Ethernet Modules Front Panel
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Table 2-5
N
K
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
Note
LI
N
K
LI
N
K
LI
N
K
LI
LI
N
K
LI
24 PORT 100FX-MMF
44744
1
ST
AT
US
WS-X6324-100FX-MM
The WS-X6324-100FX-SM Ethernet module front panel is identical to the WS-X6324-100FX-MM
Ethernet module front panel with the exception of the product part number.
WS-X6324-100FX-MM and WS-X6324-100FX-SM Ethernet Module Features
Feature
Description
Ports per module
24
Connector type
MT-RJ (both modules)
Cabling distance
•
WS-X6324-100FX-MM—1.24 mi (2 km) full-duplex over MMF
•
WS-X6324-100FX-MM—1312 ft (400 m) half-duplex over MMF
•
WS-X6324-100FX-SM—6.2 mi (10 km) full- or half-duplex over
G.652 SMF
Speed
100 Mbps
Buffer size
128 KB per port
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported by the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
Both modules:
•
Tx—2q2t
•
Rx—1q4t
Chassis/slot restrictions
No chassis or slot restrictions; the modules can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
Single connection into the 32-Gbps shared bus
Catalyst 6500 Series Ethernet Modules Installation Guide
2-6
OL-6265-02
Chapter 2
Ethernet Switching Modules
10 and 10/100 Fiber-Based Ethernet Modules
Table 2-5
WS-X6324-100FX-MM and WS-X6324-100FX-SM Ethernet Module Features (continued)
Feature
Description
Module upgrades available
PoE support
Not available.
Distributed forwarding
support
Not available.
Pluggable transceivers
support
Not supported.
Digital Optical Monitoring
(DOM) support
Not supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
Table 2-6
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
Off—The port is not active or the link is not connected.
WS-X6324-100FX-MM and WS-X6324-100FX-SM Ethernet Modules Physical and Environmental
Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
7.0 lb (3.18 kg)
Power requirement
(at 42 VDC)
1.52 A (both modules)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-7
Chapter 2
Ethernet Switching Modules
10 and 10/100 Fiber-Based Ethernet Modules
WS-X6524-100FX-MM Ethernet Module
The WS-X6524-100FX-MM Ethernet module (Figure 2-4) provides 24 100-Mbps full- or half-duplex
ports. Table 2-7 lists the module features, and Table 2-8 lists the module physical and environmental
specifications.
Figure 2-4
WS-X6524-100FX-MM Switching Modules Front Panel
Table 2-7
N
K
N
K
24
LI
N
K
23
LI
N
K
22
LI
N
K
21
LI
N
K
20
LI
N
K
19
LI
N
K
18
LI
N
K
17
LI
N
K
16
LI
N
K
15
LI
N
K
14
LI
N
K
13
LI
N
K
12
LI
N
K
11
LI
N
K
10
LI
N
K
9
LI
N
K
8
LI
N
K
7
LI
N
K
6
LI
N
K
5
LI
N
K
4
LI
N
K
3
LI
LI
N
K
2
LI
1
STATUS
63671
WS-X6524-100FX-MM
24 PORT 100FX-MMF
WS-X6524-100FX-MM Features
Feature
Description
Ports per module
24
Connector type
MT-RJ
Cabling distance
1.24 mi (2 km) full-duplex; 1312 ft (400 m) half-duplex over MMF
Speed
100 Mbps
Buffer size
1.2 MB per port
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported by the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
•
Tx—1p3q1t
•
Rx—1p1q0t
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
Single connection into the 32-Gbps shared bus
Catalyst 6500 Series Ethernet Modules Installation Guide
2-8
OL-6265-02
Chapter 2
Ethernet Switching Modules
10 and 10/100 Fiber-Based Ethernet Modules
Table 2-7
WS-X6524-100FX-MM Features (continued)
Feature
Description
Module upgrades available
PoE support
Not available
Distributed forwarding
support
Field upgradeable to support distributed forwarding with the following
daughter cards:
•
WS-F6K-DFC
•
WS-F6K-DFC3A
•
WS-F6K-DFC3B
•
WS-F6K-DFC3BXL
See Appendix A for further information on the DFC daughter cards.
See the Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL
Installation Note for field installation procedures.
Pluggable transceivers
support
Not supported
Digital Optical Monitoring
(DOM) support
Not supported
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Off—The port is not active or the link is not connected.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-9
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-8
WS-X6524-100FX-MM Physical and Environmental Specifications
Item
Specification
Dimensions
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
Base module—7.0 lb (3.18 kg)
Power required
(at 42 VDC)
•
Base module—1.90 A
•
Base module + DFC3 daughter card (WS-F6K-DFC3)—4.00 A
•
Base module + DFC3A daughter card (WS-F6K-DFC3A)—4.47 A
•
Base module + DFC3B daughter card (WS-F6K-DFC3B)—3.57 A
•
Base module + DFC3BXL daughter card (WS-F6K-DFC3BXL)—3.37 A
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
10/100 and 10/100/1000 Ethernet Modules
This section describes the following 10/100 and 10/100/1000BASE Ethernet modules:
•
WS-X6148-GE-TX and WS-X6148A-GE-TX Ethernet Modules, page 2-11
•
WS-X6148-RJ21 Ethernet Modules, page 2-15
•
WS-X6148-RJ-45 and WS-X6148A-RJ-45 Ethernet Modules, page 2-18
•
WS-X6148X2-RJ-45 and WS-X6148X2-45AF Ethernet Modules, page 2-22
•
WS-X6196-RJ-21 and WS-X6196-21AF Ethernet Modules, page 2-26
•
WS-X6348-RJ21V Ethernet Module, page 2-29
•
WS-X6348-RJ45 and WS-X6348-RJ45V Ethernet Modules, page 2-32
•
WS-X6516-GE-TX Ethernet Module, page 2-35
•
WS-X6548-GE-TX, WS-X6548-GE-45AF, and WS-X6548V-GE-TX Ethernet Modules, page 2-38
•
WS-X6548-RJ-21 Ethernet Module, page 2-41
•
WS-X6548-RJ-45 Ethernet Module, page 2-44
•
WS-X6748-GE-TX Ethernet Module, page 2-47
Catalyst 6500 Series Ethernet Modules Installation Guide
2-10
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6148-GE-TX and WS-X6148A-GE-TX Ethernet Modules
The base WS-X6148-GE-TX and the base WS-X6148A-GE-TX Ethernet modules and their variants,
listed in Table 2-9, provide 48 10/100/1000-Mbps full- or half-duplex ports. Figure 2-5 shows the
module front panel.
Table 2-9
Description
WS-X6148-GE-TX
Base module without daughter cards installed.
WS-X6148-GE-45AF
Base module equipped with a factory-installed
IEEE 802.3af PoE daughter card (WS-F6K-GE48-AF).
WS-X6148V-GE-TX
Base module equipped with a factory-installed Cisco
prestandard PoE daughter card (WS-F6K-VPWR-GE).
WS-X6148A-GE-TX
Base module (with enhanced port buffer size) without
daughter cards installed.
WS-X6148A-GE-45AF
Base module (with enhanced port buffer size) equipped
with a factory-installed IEEE 802.3af PoE daughter
card (WS-F6K-GE48-AF).
WS-X6148-GE-TX Ethernet Module Front Panel
47
48
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
PHONE
90852
37
38
SWITCHING MODULE
31
10/100/1000
BASE-T GE
35
36
30
24
23
22
21
20
19
18
17
16
15
14
9
12
8
11
7
10
6
5
4
3
2
1
48 PORT
25
26
29
23
24
28
STATUS
13
14
27
11
12
2
26
1
13
WS-X6148-GE-TX
Module
25
Figure 2-5
WS-X6148-GE-TX and WS-X6148A-GE-TX Ethernet Module Variants
Table 2-10 lists the features and descriptions for the base modules and their variants, and Table 2-11 lists
the physical and environmental specifications for the base modules and their variants.
Note
Table 2-10
The WS-X6148-GE-TX and the WS-X6148A-GE-TX Ethernet modules share the same front panel. The
product numbers located in the upper-left corner will differ.
WS-X6148-GE-TX Features
Feature
Description
Ports per module
48 ports (all variants)
Connector type
RJ-45 (all variants)
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable (all variants)
Speed
10/100/1000 IEEE 802.3 triple-speed autonegotiation (all variants)
Buffer size
•
WS-X6148-GE-TX, WS-X6148V-GE-TX, and
WS-X6148-GE-45AF—1.4 MB per 8 ports
•
WS-X6148A-GE-TX and WS-X6148A-GE-45AF—5.5 MB per port
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-11
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-10
WS-X6148-GE-TX Features (continued)
Feature
Description
Maximum frame size
Supervisor engine support
Queues per port
•
WS-X6148-GE-TX, WS-X6148V-GE-TX, and
WS-X6148-GE-45AF—Up to 1518 bytes per frame
•
WS-X6148A-GE-TX and WS-X6148A-GE-45AF—Up to 9216 bytes
per frame
Supported by the following supervisor engines:
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
WS-X6148-GE-TX, WS-X6148V-GE-TX, and WS-X6148-GE-45AF:
•
Tx—1p2q2t (per 8 ports)
•
Rx—1p2t (per port)
WS-X6148A-GE-TX and WS-X6148A-GE-45AF:
•
Tx—1p3q8t
•
Rx—1q2t
Chassis/slot restrictions
No chassis or slot restrictions: the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis (all variants)
Bus connection
Single connection into the 32-Gbps shared bus (all variants).
Module upgrades available
PoE support
WS-X6148-GE-TX and WS-X6148A-GE-TX:
•
The WS-X6148-GE-TX is field upgradeable with the
WS-F6K-VPWR-GE= daughter card that supports only the Cisco
prestandard.
•
Both the WS-X6148-GE-TX and the WS-X6148A-GE-TX are field
upgradeable with the WS-F6K-GE48-AF= daughter card that supports
both the Cisco prestandard and the IEEE 802.3af standard.
Refer to the Catalyst 6500 Series Power over Ethernet Daughter Cards
Field-Upgrade Installation Note for field upgrade procedures.
Refer to Appendix A for additional information on the PoE daughter cards.
Distributed forwarding
support
Not supported.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-12
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-10
WS-X6148-GE-TX Features (continued)
Feature
Description
Pluggable transceivers
support
Not supported.
TDR support
All variants are supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-13
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-11
WS-X6148-GE-TX and Variants Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
Power requirement
(at 42 VDC)
•
WS-X6148-GE-TX (base module only)—7.6 lb (3.4 kg)
•
WS-X6148A-GE-TX (base module only)—6.6 lb (3 kg)
•
WS-X6148-GE-TX (base module)—2.47 A
•
WS-X6148-GE-45AF (base module + PoE daughter card)—2.65 A
•
WS-X6148V-GE-TX (base module + PoE daughter card)—2.89 A
•
WS-X6148A-GE-TX (enhanced base module)—2.50 A
•
WS-X6148A-GE-45AF (enhanced base module + PoE daughter
card)—2.68 A
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-14
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6148-RJ21 Ethernet Modules
The WS-X6148-RJ21 Ethernet module and its two variants, listed in Table 2-12, provide 48
10/100/1000-Mbps full- or half-duplex ports. Figure 2-6 shows the module front panel.
Table 2-12
Figure 2-6
WS-X6148-RJ21 Ethernet Module Variants
Module
Description
WS-X6148-RJ21
Base module without daughter cards installed.
WS-X6148-21AF
Base module equipped with a factory-installed
IEEE 802.3af PoE daughter card (WS-F6K-GE48-AF).
WS-X6148-RJ21V
Base module equipped with a factory-installed Cisco
prestandard PoE daughter card (WS-F6K-VPWR-GE).
WS-X6148-RJ-21 Ethernet Module Front Panel
8
48 PORT
10/100 BASE-T
ETHERNET
SWITCHING MODULE
48
47
46
45
44
43
42
41
40
39
38
PHONE
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
9
12
8
11
7
10
6
5
4
3
2
1
STATUS
184592
37
-4
25
-3
13
1-
12
-2
6
4
WS-X6148-RJ-21
Table 2-13 lists the features and descriptions for the modules, and Table 2-14 lists the physical and
environmental specifications for the modules.
Table 2-13
WS-X6148-RJ-21 Ethernet Modules Features
Feature
Description
Ports per module
48 ports (all variants)
Connector type
RJ-21 (all variants)
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable (all variants)
Speed
10/100/1000 IEEE 802.3 triple-speed autonegotiation (all variants)
Buffer size
128 KB per port (all variants)
Maximum frame size
Up to 8092 bytes per frame (all variants)
Supervisor engine support
Supported by the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
All variants:
•
Tx—2q2t
•
Rx—1q4t
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-15
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-13
WS-X6148-RJ-21 Ethernet Modules Features (continued)
Feature
Description
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis (all variants).
Bus connection
Single connection into the 32-Gbps shared bus (all variants)
Daughter card support
PoE support
WS-X6148-RJ-21—Field upgradeable to Cisco Prestandard only by
installing the WS-F6K-VPWR= daughter card.
Refer to the Cisco Catalyst 6500 Series Power over Ethernet Daughter
Cards Field-Upgrade Installation Note for field upgrade procedures.
An IEEE 802.3af standard PoE daughter card is available
through factory advance replacement only; the IEEE 802.3af
standard PoE daughter card is not field upgradeable.
Note
Distributed forwarding
support
Not available.
Pluggable transceivers
support
Not supported.
TDR support
All variants supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-16
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-14
WS-X6148-RJ-21 Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
•
Base module only—8.0 lb (3.6 kg)
Power requirement
(at 42 VDC)
•
WS-X6148-RJ-21 (base module)—2.39 A
•
WS-X6148-21AF (base module + PoE daughter card)—2.57 A
•
WS-X6148-RJ21V (base module + PoE daughter card)—2.81 A
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-17
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6148-RJ-45 and WS-X6148A-RJ-45 Ethernet Modules
The WS-X6148-RJ-45 and the WS-X6148A-RJ-45 Ethernet modules provide 48 10/100/1000-Mbps
full- or half-duplex ports. Table 2-15 lists the two base modules and their variants. Figure 2-7 shows the
module front panel.
Table 2-15
Figure 2-7
WS-X6148-RJ-45 and WS-X61248A-RJ-45 Ethernet Modules and Variants
Module
Description
WS-X6148-RJ-45
Base module without daughter cards installed.
WS-X6148-45AF
Base module equipped with a factory-installed
IEEE 802.3af PoE daughter card (WS-F6K-GE48-AF).
WS-X6148-RJ45V
Base module equipped with a factory-installed Cisco
prestandard PoE daughter card (WS-F6K-VPWR-GE).
WS-X6148A-RJ-45
Base module (with enhanced port buffer size) without
daughter cards installed.
WS-X6148A-45AF
Base module (with enhanced port buffer size) equipped
with a factory-installed IEEE 802.3af PoE daughter
card (WS-F6K-GE48-AF).
WS-X6148-RJ-45 Ethernet Module Front Panel
48
47
46
45
44
43
42
41
40
39
38
39334
47
48
37
38
37
36
35
34
33
32
31
30
29
28
27
26
PHONE
25
ETHERNET SWITCHING
MODULE
35
36
25
26
23
24
24
23
22
21
20
19
18
17
16
15
13
14
48 PORT
10/100 BASE-T
14
9
12
8
11
7
10
6
5
4
3
2
1
STATUS
13
2
1
11
12
WS-X6348-RJ-45V
Table 2-16 lists the features and descriptions for the modules, and Table 2-17 lists the physical and
environmental specifications for the modules.
Note
Table 2-16
The WS-X6148-RJ-45 and the WS-X6148A-RJ-45 Ethernet modules share the same front panel. The
product numbers in the upper-left corner will differ.
WS-X6148-RJ-45 and WS-X6148A-RJ-45 Ethernet Modules Features
Feature
Description
Ports per module
48 ports (all variants)
Connector type
RJ-45 (all variants)
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable (all variants)
Speed
10/100/1000 IEEE 802.3 triple-speed autonegotiation (all variants)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-18
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-16
WS-X6148-RJ-45 and WS-X6148A-RJ-45 Ethernet Modules Features (continued)
Feature
Buffer size
Maximum frame size
Supervisor engine support
Queues per port
Description
•
WS-X6148-RJ-45, WS-X6148-45AF, and
WS-X6148-RJ45V—1 MB per 8 ports
•
WS-X6148A-RJ-45 and WS-X6148A-45AF—5.3 MB per 8 ports
•
WS-X6148-RJ-45, WS-X6148-45AF, and
WS-X6148-RJ45V—Up to 8092 bytes per frame
•
WS-X6148A-RJ-45 and WS-X6148A-45AF—Up to 9216 bytes
per frame
Supported on the following supervisor engines:
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
WS-X6148-RJ-45, WS-X6148-45AF, and WS-X6148-RJ45V:
•
Tx—1p2q2t per 8 ports
•
Rx—1p2t per port
WS-X6148A-RJ-45 and WS-X6148A-45AF:
•
Tx—1p3q8t
•
Rx—1q2t
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis (all variants).
Bus connection
Single connection into the 32-Gbps shared bus (all variants)
Module upgrades available
PoE support
•
WS-X6148-RJ-45—Field upgradeable to the Cisco prestandard
only with the WS-F6K-VPWR-GE= daughter card or both the
Cisco prestandard and the IEEE 802.3af standard by installing the
WS-F6K-GE48-AF= daughter card.
•
WS-X6148A-RJ-45—Field upgradeable to the Cisco prestandard
and the IEEE 802.3af standard by installing the
WS-F6K-GE48-AF= daughter card.
See the Cisco Catalyst 6500 Series Power over Ethernet Daughter
Cards Field-Upgrade Installation Note for field upgrade procedures.
See Appendix A for further information on the PoE daughter cards.
Distributed forwarding
support
Not supported.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-19
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-16
WS-X6148-RJ-45 and WS-X6148A-RJ-45 Ethernet Modules Features (continued)
Feature
Description
Pluggable transceivers
support
Not supported.
TDR support
Yes
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics.
An overtemperature condition has occurred. (A minor temperature
threshold has been exceeded during environmental monitoring.)
•
Red—The module is resetting. The switch has just been powered
on or the module has been hot inserted during the normal
initialization sequence.
An overtemperature condition has occurred. (A major temperature
threshold has been exceeded during environmental monitoring.)
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
LINK
•
Green—The port is active (the link is connected and operational).
•
Orange—The module or port is disabled through the CLI command
or the module is initializing.
•
Flashing orange—The port is faulty and has been disabled.
•
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-20
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-17
WS-X6148-RJ-45 Ethernet Modules Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
Power requirement
(at 42 VDC)
•
WS-X6148-RJ-45 (Base module)—6.8 lb (3.08 kg)
•
WS-X6148A-RJ-45 (Enhanced base module)—7.2 lb (3.27 kg)
•
WS-X6148-RJ-45—2.39 A
•
WS-X6148-45AF (base module + PoE daughter card) —2.57 A
•
WS-X6148-RJ45V (base module + PoE daughter card)—2.81 A
•
WS-X6148A-RJ-45—1.00 A
•
WS-X6148A-RJ45AF (enhanced base module + PoE daughter card)—1.18 A
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-21
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6148X2-RJ-45 and WS-X6148X2-45AF Ethernet Modules
The WS-X6148X2-RJ-45 and the WS-X6148X2-45AF Ethernet modules, listed in Table 2-18, provide
96 10/100-Mbps full- or half-duplex ports. The WS-X6148X2-RJ-45 and the WS-X6148X2-RJ-45AF
modules, see Figure 2-8, are shipped with a 96-port splitter panel (WS-F6K-48X2-SPLTR). (See
Figure 2-9.)
Table 2-18
WS-X6148X2-RJ-45 and the WS-X6148X2-45AF Ethernet modules
Module
Description
WS-X6148X2-RJ-45
Base module without daughter cards installed.
WS-X6148X2-45AF
Base module equipped with a factory-installed
IEEE 802.3af PoE daughter card (WS-F6K-GE48-AF).
WS-X6148X2-RJ-45 Ethernet Module Front Panel
Figure 2-9
WS-F6K-48X2-SPLTR Splitter Panel
184593
Figure 2-8
1
CATALYST
184594
49
2
50
Table 2-19 lists the features for the modules, and Table 2-20 lists the physical and environmental
specifications for the module.
Note
With the IEEE 802.3af PoE daughter card installed, the WS-X6148X2-RJ-45 module can support up to
48 Class 3 (15.4 W) devices per module when operating as a 48-port module or up to 96 Class 2 (7 W)
devices per module when operating as a 96-port module.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-22
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-19
WS-X6148X2-RJ-45 and WS-X6148X2-45AF Ethernet Modules Features
Feature
Description
Ports per module
48, but scalable to 96 ports with the use of the supplied splitter panel
(both modules)
Connector type
RJ-45 (both modules)
RJ-45 (splitter panel)
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable (both
modules)
Speed
10/100 IEEE 802.3 double-speed autonegotiation (both modules)
Buffer size
1.116 MB per port (both modules)
Maximum frame size
Up to 9216 bytes per frame (both modules)
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
Both modules:
•
Tx—2q2t
•
Rx—1q4t
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
Single connection into the 32-Gbps shared bus (both modules)
Module upgrades available
PoE support
•
Note
WS-X6148X2-RJ-45—Field upgradeable to both Cisco
prestandard and IEEE 802.3af with the WS-F6K-FE48X2-AF=
PoE daughter card.
With the IEEE 802.3af PoE daughter card installed, the
WS-X6148X2-RJ-45 module can support up to 48 Class 3
(15.4 W) devices per module when operating as a 48-port
module or up to 96 Class 2 (7 W) devices per module when
operating as a 96-port module.
See the Cisco Catalyst 6500 Series Power over Ethernet Daughter
Cards Field-Upgrade Installation Note for field upgrade procedures.
See Appendix A for further information on the PoE daughter cards.
Distributed forwarding
support
Pluggable transceivers
support
Not supported.
Not supported.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-23
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-19
WS-X6148X2-RJ-45 and WS-X6148X2-45AF Ethernet Modules Features (continued)
Feature
Description
TDR support
Not supported
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics.
An overtemperature condition has occurred. (A minor temperature
threshold has been exceeded during environmental monitoring.)
•
Red—The module is resetting. The switch has just been powered
on or the module has been hot inserted during the normal
initialization sequence.
An overtemperature condition has occurred. (A major temperature
threshold has been exceeded during environmental monitoring.)
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
LINK
•
Green—The port is active (the link is connected and operational).
•
Orange—The module or port is disabled through the CLI command
or the module is initializing.
•
Flashing orange—The port is faulty and has been disabled.
•
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-24
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-20
WS-X6148X2-RJ-45 Specifications
Item
Specification
Dimensions (H x W x D)
Module—1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the
chassis.
Splitter panel—3.5 x 19 x 1.25 in. (8.9 x 48.26 x 3.18 cm). Occupies 2 RUs in the
rack.
Weight
WS-X6148X2-RJ-45 (base module)—7.2 lb (3.26 kg)
Splitter panel—5.2 lb (2.36 kg)
Power requirement
(at 42 VDC)
•
WS-X6148X2-RJ-45 (base module)—2.65 A
•
WS-X6148X2-45AF (base module + PoE daughter card)—3.07 A
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-25
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6196-RJ-21 and WS-X6196-21AF Ethernet Modules
The WS-X6196-RJ-21 and the WS-X6196-21AF Ethernet modules, listed in Table 2-21, provide 96
10/100-Mbps full- or half-duplex ports. Figure 2-10 shows the module front panel.
Table 2-21
Description
WS-X6196-RJ-21
Base module without daughter cards installed.
WS-X6196-21AF
Base module equipped with a factory-installed
IEEE 802.3af PoE daughter card (WS-F6K-GE48-AF).
WS-X6196-RJ-21 Switching Module Front Panel
1
12
13
24
25
36
37
48
60
49
72
61
84
73
96
85
ST
AT
US
WS-X6196-RJ-21
Module
8X12 PORT
10/100 BASE T
ETHERNET SWITCHING MODULE
47
95
48
96
46
94
93
92
45
43
91
44
90
89
42
41
40
88
38
86
39
87
85
84
37
36
82
35
83
80
33
81
34
79
32
30
78
31
77
75
28
76
29
27
72
25
74
24
73
26
22
70
23
71
69
67
20
68
21
66
19
18
65
63
16
64
17
15
61
14
62
59
12
60
13
11
10
58
8
56
9
57
6
54
7
55
3
51
4
52
5
53
1
49
2
50
INLINE POWER
184595
Figure 2-10
WS-X6196-RJ-21 Modules
Table 2-22 lists the module features, and Table 2-23 lists the module physical and environmental
specifications.
Note
Table 2-22
With the PoE daughter card installed, the WS-X6196-RJ-21 module can support 96 Class 2 (7 W)
devices or 62 Class 3 (15.4 W) devices per module.
WS-X6196-RJ-21 and WS-X6196-21AF Ethernet Modules Features
Feature
Description
Ports per module
96 ports (both modules)
Connector type
RJ-21 (both modules)
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable (both
modules)
Speed
10/100 IEEE 802.3 double-speed autonegotiation (both modules)
Buffer size
1.116 MB per port (both modules)
Maximum frame size
Up to 9216 bytes (both modules)
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
Both modules:
•
Tx—1p3q1t
•
Rx—1p1q0t
Catalyst 6500 Series Ethernet Modules Installation Guide
2-26
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-22
WS-X6196-RJ-21 and WS-X6196-21AF Ethernet Modules Features (continued)
Feature
Description
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
32-Gbps shared bus (both modules)
Module upgrades available
PoE support
WS-X6196-RJ-21—Field upgradeable to both Cisco prestandard and
IEEE 802.3af with the WS-F6K-FE48X2-AF= PoE daughter card.
With the PoE daughter card installed, the WS-X6196-RJ-21
module can support 96 Class 2 (7 W) devices or 62 Class 3
(15.4 W) devices per module.
Note
See the Cisco Catalyst 6500 Series Power over Ethernet Daughter
Cards Field-Upgrade Installation Note for field upgrade procedures.
See Appendix A for further information on the PoE daughter cards.
Distributed forwarding
support
Not supported.
Pluggable transceivers
support
Not supported.
TDR support
Not supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics.
An overtemperature condition has occurred. (A minor temperature
threshold has been exceeded during environmental monitoring.)
•
Red—The module is resetting. The switch has just been powered
on or the module has been hot inserted during the normal
initialization sequence.
An overtemperature condition has occurred. (A major temperature
threshold has been exceeded during environmental monitoring.)
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
LINK
•
Green—The port is active (the link is connected and operational).
•
Orange—The module or port is disabled through the CLI command
or the module is initializing.
•
Flashing orange—The port is faulty and has been disabled.
•
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-27
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-23
WS-X6196-RJ-21 and WS-X6196-21AF Ethernet Modules Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
WS-X6196-RJ-21—7.8 lb (3.54 kg)
WS-X6196-21AF—11.2 lb (5.08 kg)
Power requirement
(at 42 VDC)
•
WS-X6196-RJ-21 (base module)—2.74 A
•
WS-X6196-21AF (base module + PoE daughter card)—3.16 A
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-28
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6348-RJ21V Ethernet Module
The WS-X6348-RJ21V Ethernet module (Figure 2-11) provides 48 10/100-Mbps full- or half-duplex
ports. Table 2-24 lists the features and description for the module, and Table 2-25 lists the physical and
environmental specifications for the module.
Figure 2-11
WS-X6348-RJ21 Switching Module
8
48 PORT
10/100 BASE-T
ETHERNET
SWITCHING MODULE
48
47
46
45
44
43
42
41
40
39
38
PHONE
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
9
12
8
11
7
Table 2-24
10
6
5
4
3
2
1
STATUS
68149
37
-4
6
25
-3
13
1-
12
-2
4
WS-X6348-RJ21
WS-X6348-RJ21V Features
Feature
Description
Ports per module
48
Connector type
RJ-21
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable
Speed
10/100 IEEE 802.3 double-speed autonegotiation
Buffer size
128 KB
Maximum frame size
Up to 8092 bytes per frame
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
•
Tx—2q2t
•
Rx—1q4t
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
32-Gbps shared bus
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-29
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-24
WS-X6348-RJ21V Features (continued)
Feature
Description
Module upgrades available
PoE support
Cisco prestandard only. The WS-F6K-VPWR= PoE daughter card is
factory installed on the module. No PoE field upgrades are available.
Distributed forwarding
support
Not supported.
Pluggable transceivers
support
Not supported.
TDR support
Not supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics.
An overtemperature condition has occurred. (A minor temperature
threshold has been exceeded during environmental monitoring.)
•
Red—The module is resetting. The switch has just been powered
on or the module has been hot inserted during the normal
initialization sequence.
An overtemperature condition has occurred. (A major temperature
threshold has been exceeded during environmental monitoring.)
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
LINK
•
Green—The port is active (the link is connected and operational).
•
Orange—The module or port is disabled through the CLI command
or the module is initializing.
•
Flashing orange—The port is faulty and has been disabled.
•
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-30
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-25
WS-X6348-RJ21V Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the
chassis.
Weight
9.1 lb (4.13 kg)
Power required
(at 42 VDC)
2.81 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to
3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-31
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6348-RJ45 and WS-X6348-RJ45V Ethernet Modules
The WS-X6348-RJ45 and the WS-X6348-RJ45V Ethernet modules, listed in Table 2-26, provide 48
10/100-Mbps full- or half-duplex ports. Figure 2-12 shows the module front panel.
Table 2-26
Figure 2-12
WS-X6348-RJ45 Modules
Module
Description
WS-X6348-RJ45
Base module without daughter cards installed.
WS-X6348-RJ45V
Base module equipped with a factory-installed Cisco
prestandard PoE daughter card (WS-F6K-VPWR-GE).
WS-X6348-RJ45 and WS-X6348-RJ45V Ethernet Modules Front Panel
48
47
46
45
44
42
41
40
43
39
38
37
36
35
34
33
32
31
30
29
28
27
PHONE
26
ETHERNET SWITCHING
MODULE
25
24
23
22
21
20
19
18
17
16
15
14
48 PORT
10/100 BASE-T
13
9
12
8
11
7
10
6
5
4
3
2
1
STATUS
39496
48
36
38
24
26
12
2
14
1
WS-X6348-RJ-45
Table 2-27 lists the module features, and Table 2-28 lists the module physical and environmental
specifications.
Table 2-27
WS-X6348-RJ45 and WS-X6348-RJ45V Ethernet Modules Features
Feature
Description
Ports per module
48 (both modules)
Connector type
RJ-45 (both modules)
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable (both
modules)
Speed
10/100 IEEE 802.3 double-speed autonegotiation (both modules)
Buffer size
128 KB per port (both modules)
Maximum frame size
Up to 8092 bytes per frame (both modules)
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
Both modules:
•
Tx—2q2t
•
Rx—1q4t
Chassis/slot restrictions
No chassis or slot restrictions; the modules can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
32-Gbps shared bus (both modules)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-32
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-27
WS-X6348-RJ45 and WS-X6348-RJ45V Ethernet Modules Features (continued)
Feature
Description
Module upgrades available
PoE support
•
WS-X6348-RJ45—Field upgradeable to Cisco prestandard with
the WS-F6K-VPWR= PoE daughter card.
See the Cisco Catalyst 6500 Series Power over Ethernet Daughter
Cards Field-Upgrade Installation Note for field upgrade procedures.
See Appendix A for further information on the PoE daughter cards.
Distributed forwarding
support
Not supported.
Pluggable transceivers
support
Not supported.
TDR support
Not supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics.
An overtemperature condition has occurred. (A minor temperature
threshold has been exceeded during environmental monitoring.)
•
Red—The module is resetting. The switch has just been powered
on or the module has been hot inserted during the normal
initialization sequence.
An overtemperature condition has occurred. (A major temperature
threshold has been exceeded during environmental monitoring.)
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
LINK
•
Green—The port is active (the link is connected and operational).
•
Orange—The module or port is disabled through the CLI command
or the module is initializing.
•
Flashing orange—The port is faulty and has been disabled.
•
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-33
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-28
WS-X6348-RJ45 and WS-X6348-RJ45V Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the
chassis.
Weight
Power requirement
(at 42 VDC)
•
WS-X6348-RJ45—7.2 lb (3.26 kg)
•
WS-X6348-RJ45V—8.8 lb (3.99 kg)
•
WS-X6348-RJ45—2.39 A
•
WS-X6348-RJ45V (base module + PoE daughter card)—2.81 A
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to
3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-34
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6516-GE-TX Ethernet Module
The WS-X6516-GE-TX Ethernet module (Figure 2-13) provides 16 10/100/1000-Mbps full- or
half-duplex ports. Table 2-29 lists the features and description for the module, and Table 2-30 lists the
physical and environmental specifications for the module.
Figure 2-13
WS-X6516-GE-TX Ethernet Module
5
6
7
8
LIN
K
4
LIN
K
3
LIN
K
2
LIN
K
1
9
10
11
12
13
14
15
16
Table 2-29
63187
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
LIN
K
16 PORT 1000 BASE-T GE
LIN
K
ST
AT
U
S
WS-X6516-GE-T X
WS-X6516-GE-TX Ethernet Module Features
Feature
Description
Ports per module
16
Connector type
RJ-45
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable
Speed
10/100/1000 IEEE 802.3 triple-speed autonegotiation
Buffer size
512 KB per port
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
•
Tx—1p2q2t
•
Rx—1p1q4t
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
32-Gbps shared bus
Module upgrades available
PoE support
Not supported.
Distributed forwarding
support
Not supported.
Pluggable transceivers
support
Not supported.
TDR support
Not supported.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-35
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-29
WS-X6516-GE-TX Ethernet Module Features (continued)
Feature
Description
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics.
An overtemperature condition has occurred. (A minor temperature
threshold has been exceeded during environmental monitoring.)
•
Red—The module is resetting. The switch has just been powered
on or the module has been hot inserted during the normal
initialization sequence.
An overtemperature condition has occurred. (A major temperature
threshold has been exceeded during environmental monitoring.)
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
LINK
•
Green—The port is active (the link is connected and operational).
•
Orange—The module or port is disabled through the CLI command
or the module is initializing1.
•
Flashing orange—The port is faulty and has been disabled.
•
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
1. Verify that all LINK LEDs are functioning.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-36
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-30
WS-X6516-GE-TX Ethernet Module Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the
chassis.
Weight
7.65 lb (3.43 kg)
Power requirement
(at 42 VDC)
3.45 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to
3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-37
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6548-GE-TX, WS-X6548-GE-45AF, and WS-X6548V-GE-TX Ethernet
Modules
The WS-X6548-GE-TX Ethernet module and its variants, listed in Table 2-31, provide 48
10/100/1000-Mbps full- or half-duplex ports. Figure 2-14 shows the module front panel.
Table 2-31
Description
WS-X6548-GE-TX
Base module without daughter cards installed.
WS-X6548-GE-45AF
Base module equipped with a factory-installed
IEEE 802.3af PoE daughter card (WS-F6K-GE48-AF).
WS-X6548V-GE-TX
Base module equipped with a factory-installed Cisco
prestandard PoE daughter card (WS-F6K-VPWR-GE).
WS-X6548-GE-TX Ethernet Module Front Panel
47
48
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
PHONE
184596
37
38
SWITCHING MODULE
31
10/100/1000
BASE-T GE
35
36
30
24
23
22
21
20
19
18
17
16
15
14
12
9
11
8
10
7
6
5
4
3
2
1
48 PORT
25
26
29
23
24
28
STATUS
13
14
27
11
12
2
26
1
13
WS-X6548-GE-TX
Module
25
Figure 2-14
WS-X6548-GE-TX Ethernet Module Variants
Table 2-32 lists the features and descriptions for the modules, and Table 2-33 lists the physical and
environmental specifications for the modules.
Table 2-32
WS-X6548-GE-TX Modules Features
Feature
Description
Ports per module
48 (all variants)
Connector type
RJ-45 (all variants)
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable (all variants)
Speed
10/100/1000 IEEE 802.3 triple-speed autonegotiation (all variants)
Buffer size
1.4 MB per 8 ports
Maximum frame size
Up to 1518 bytes per frame
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
•
Tx—1p2q2t (per 8 ports)
•
Rx—1p2t (per 8 ports)
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis (all variants).
Bus connection
32-Gbps shared bus (all variants)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-38
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-32
WS-X6548-GE-TX Modules Features (continued)
Feature
Description
Module upgrades available
PoE support
WS-X6548-GE-TX—Field-upgradeable to Cisco prestandard only by
installing the WS-F6K-VPWR-GE= daughter card or both Cisco
prestandard and IEEE 802.3af by installing the WS-F6K-GE48-AF=
daughter card.
Refer to the Cisco Catalyst 6500 Series Power over Ethernet
Daughter Cards Field-Upgrade Installation Note for field
upgrade procedures.
Note
Distributed forwarding
support
Not supported.
Pluggable transceivers
support
Not supported.
TDR support
All module variants support TDR.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics.
An overtemperature condition has occurred. (A minor temperature
threshold has been exceeded during environmental monitoring.)
•
Red—The module is resetting. The switch has just been powered
on or the module has been hot inserted during the normal
initialization sequence.
An overtemperature condition has occurred. (A major temperature
threshold has been exceeded during environmental monitoring.)
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
LINK
•
Green—The port is active (the link is connected and operational).
•
Orange—The module or port is disabled through the CLI command
or the module is initializing1.
•
Flashing orange—The port is faulty and has been disabled.
•
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
1. Verify that all LINK LEDs are functioning.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-39
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-33
WS-X6548-GE-TX and Variants Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the
chassis.
Weight
Base module—7.2 lb (3.3 kg)
Power requirement
(at 42 VDC)
•
WS-X6548-GE-TX (base module)—2.98 A
•
WS-X6548-GE-45AF (base module + PoE daughter card)—3.16 A
•
WS-X6548V-GE-TX (base module + PoE daughter card)—3.40 A
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to
3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-40
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6548-RJ-21 Ethernet Module
The WS-X6548-RJ-21 Ethernet module (Figure 2-15) provides 48 10/100-Mbps full- or half-duplex
ports. Table 2-34 lists the features and description of the module, and Table 2-35 lists the physical and
environmental specifications for the module.
Figure 2-15
WS-X6548-RJ-21 Ethernet Module Front Panel
8
48 PORT
10/100 BASE-T
ETHERNET
SWITCHING MODULE
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
9
12
8
11
7
Table 2-34
10
6
5
4
3
2
1
STATUS
63672
37
-4
6
25
-3
13
1-
12
-2
4
WS-X6548-RJ21
WS-X6548-RJ-21 Ethernet Module Features
Feature
Description
Ports per module
48 ports
Connector type
RJ-21
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable
Speed
10/100 IEEE 802.3 double-speed autonegotiation
Buffer size
1.116 MB per port
Maximum frame size
Up to 1518 bytes per frame.
Supervisor engine support
All module variants support all supervisor engines.
Queues per port
•
Tx—1p3q8t
•
Rx—1q2t
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
32-Gbps shared bus
Module upgrades available
PoE support
Not available.
Distributed forwarding
support
Can be field-upgraded with either the WS-F6K-DFC,
WS-F6K-DFC3B, or WS-F6K-DFC3BXL daughter cards.
See the Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL
Installation Note for additional information and field upgrade
procedures.
See Appendix A for additional information on the DFC daughter cards.
Pluggable transceivers
support
Not supported.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-41
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-34
WS-X6548-RJ-21 Ethernet Module Features (continued)
Feature
Description
TDR support
Not supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics.
An overtemperature condition has occurred. (A minor temperature
threshold has been exceeded during environmental monitoring.)
•
Red—The module is resetting. The switch has just been powered
on or the module has been hot inserted during the normal
initialization sequence.
An overtemperature condition has occurred. (A major temperature
threshold has been exceeded during environmental monitoring.)
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
LINK
•
Green—The port is active (the link is connected and operational).
•
Orange—The module or port is disabled through the CLI command
or the module is initializing1.
•
Flashing orange—The port is faulty and has been disabled.
•
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
1. Verify that all LINK LEDs are functioning.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-42
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-35
WS-X6548-RJ-21 Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the
chassis.
Weight
7.6 lb (3.45 kg)
Power required
(at 42 VDC)
2.90 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to
3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-43
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6548-RJ-45 Ethernet Module
The WS-X6548-RJ-45 Ethernet module (Figure 2-16) provides 48 10/100-Mbps full- or half-duplex
ports. Table 2-36 lists the features and descriptions of the module, and Table 2-37 lists the physical and
environmental specifications for the module.
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
63673
47
48
48
PH
O
N
E
37
38
SWITCHING MODULE
31
10/100 BASE-T
ETHERNET
35
36
30
24
23
22
21
20
19
18
17
16
15
14
9
12
8
11
7
Table 2-36
10
6
5
4
3
2
1
48 PORT
25
26
29
23
24
28
STATUS
13
14
27
11
12
2
26
1
13
WS-X6548
WS-X6548-RJ-45 Switching Module Front Panel
25
Figure 2-16
WS-X6548-RJ-45 Features
Feature
Description
Ports per module
48 ports
Connector type
RJ-45
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable
Speed
10/100 IEEE 802.3 double-speed autonegotiation
Buffer size
1.116 MB per port
Maximum frame size
Up to 1518 bytes per frame
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
•
Tx—1p3q1t
•
Rx—1p1q
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
One 8-Gbps fabric connection and 32-Gbps shared bus
Module upgrades available
PoE support
Not supported.
Distributed forwarding
support
Can be field-upgraded with either the WS-F6K-DFC,
WS-F6K-DFC3B, or WS-F6K-DFC3BXL daughter cards.
See the Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL
Installation Note for additional information and field upgrade
procedures.
See Appendix A for additional information on the DFC daughter cards.
Pluggable transceivers
support
Not supported.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-44
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-36
WS-X6548-RJ-45 Features (continued)
Feature
Description
TDR support
Not supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics.
An overtemperature condition has occurred. (A minor temperature
threshold has been exceeded during environmental monitoring.)
•
Red—The module is resetting. The switch has just been powered
on or the module has been hot inserted during the normal
initialization sequence.
An overtemperature condition has occurred. (A major temperature
threshold has been exceeded during environmental monitoring.)
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
LINK
•
Green—The port is active (the link is connected and operational).
•
Orange—The module or port is disabled through the CLI command
or the module is initializing1.
•
Flashing orange—The port is faulty and has been disabled.
•
Off—The port is not active or the link is not connected.
PHONE
•
Green—The PoE daughter card is installed and detected.
•
Off—The PoE daughter card is not detected or is not installed.
1. Verify that all LINK LEDs are functioning.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-45
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-37
WS-X6548-RJ-45 Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the
chassis.
Weight
7.6 lb (3.45 kg)
Power required
(at 42 VDC)
2.9 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to
3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-46
OL-6265-02
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
WS-X6748-GE-TX Ethernet Module
The WS-X6748-GE-TX Ethernet module (Figure 2-17) provides 48 10/100/1000-Mbps full- or
half-duplex ports. Table 2-38 lists the module features, and Table 2-39 lists the module physical and
environmental specifications.
Figure 2-17
48 PORT 10/100/1000 RJ-45
11
12
2
13
14
23
24
25
26
35
36
37
38
47
48
99884
1
48
47
46
45
44
43
42
41
40
39
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
9
12
8
11
7
10
6
5
4
3
2
1
Table 2-38
38
SWITCHING MODULE
STATUS
37
WS-X6748-GE-TX
WS-X6748-GE-TX Ethernet Module Front Panel
WS-X6748-GE-TX Ethernet Module Features
Feature
Description
Ports per module
48 ports
Connector type
RJ-45
Cabling distance
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable
Speed
10/100/1000 IEEE 802.3 triple-speed autonegotiation
Buffer size
1.3 MB per port
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 720
•
Tx—1p3q8t
•
Rx—1q8t (when using distributed CEF)
Chassis/slot restrictions
The module can occupy any slot in any Catalyst 6500 or
Catalyst 6500-E chassis except the Catalyst 6513 chassis where the
module must be installed in slots 9 through 13.
Bus connection
Dual 20-GBps channel connection to the switch fabric on the
Supervisor Engine 720
Module upgrades available
PoE support
Distributed forwarding
support
Not supported.
•
Can be upgraded in the field to support dCEF with the installation
of a dCEF daughter card (WS-F6700-DFC3A, WS-F6700-DFC3B,
or the WS-F6700-DFC3BXL).
See the Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL
Installation Note for additional information and field upgrade
procedures.
See Appendix A for additional information on the DFC daughter cards.
Pluggable transceivers
support
Not supported.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-47
Chapter 2
Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Modules
Table 2-38
WS-X6748-GE-TX Ethernet Module Features (continued)
Feature
Description
TDR support
Supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics.
An overtemperature condition has occurred. (A minor temperature
threshold has been exceeded during environmental monitoring.)
•
Red—The module is resetting. The switch has just been powered
on or the module has been hot inserted during the normal
initialization sequence.
An overtemperature condition has occurred. (A major temperature
threshold has been exceeded during environmental monitoring.)
If the module fails to download code and configuration information
successfully during the initial reset, the LED stays red; the module
does not come online.
LINK
Green—The port is active (the link is connected and operational).
Orange—The module or port is disabled through the CLI command or
the module is initializing1.
Flashing orange—The port is faulty and has been disabled.
Off—The port is not active or the link is not connected.
PHONE
Green—The PoE daughter card is installed and detected.
Off—The PoE daughter card is not detected or is not installed.
1. Verify that all LINK LEDs are functioning.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-48
OL-6265-02
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-39
WS-X6748-GE-TX Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
Base module + CFC daughter card (WS-F6700-CFC)—10.2 lb (4.63 kg)
Power requirement
(at 42 VDC)
7.0 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
1-Gigabit Ethernet Modules
This section describes the following 1-Gigabit Ethernet modules:
•
WS-X6408A-GBIC, page 2-50
•
WS-X6416-GBIC, page 2-53
•
WS-X6516-GBIC and WS-X6516A-GBIC, page 2-55
•
WS-X6724-SFP, page 2-58
•
WS-X6748-SFP, page 2-61
•
WS-X6816-GBIC, page 2-64
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-49
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
WS-X6408A-GBIC
The WS-X6408A-GBIC Ethernet module (Figure 2-18) provides 8 1-Gbps full- or half-duplex ports.
Table 2-40 lists the features and descriptions for the module, and Table 2-41 lists the physical and
environmental specifications for the module.
Figure 2-18
WS-X6408A-GBIC Ethernet Module Front Panel
2
3
4
5
6
7
8
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
N
K
LI
LI
N
K
ST
8 PORT GIGABIT ETHERNET
16061
1
AT
US
WS-X6408
1000BASE-X GBIC ports
Table 2-40
WS-X6408A-GBIC Ethernet Module Features
Feature
Description
Ports per module
8
Connector type
SC or RJ-45 depending on the GBIC transceiver installed
Cabling distance
Depends on the GBIC transceiver installed in the module port. Refer to
Appendix B for descriptions of the GBIC transceiver types and
supported cabling distances.
Speed
1 Gbps
Buffer size
512 KB per port
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
•
Tx—1p2q2t
•
Rx—1p1q4t
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
32 Gbps shared bus
Module upgrades available
PoE support
Not supported.
Distributed forwarding
support
Not supported.
Pluggable transceivers
support
GBIC transceivers are supported. Refer to your software release notes
to determine which GBIC transceivers are supported. Refer to
Appendix B for additional information on the GBIC transceivers.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-50
OL-6265-02
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-40
WS-X6408A-GBIC Ethernet Module Features (continued)
Feature
Description
TDR support
Not supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Off—The port is not active or the link is not connected.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-51
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-41
WS-X6408A-GBIC Physical and Environmental Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
6.4 lb (2.9 kg)
Power requirement
(at 42 VDC)
2.00 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-52
OL-6265-02
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
WS-X6416-GBIC
The WS-X6416-GBIC Ethernet module (Figure 2-19) provides 16 1-Gbps full- or half-duplex ports.
Table 2-42 lists the module features, and Table 2-43 lists the module physical and environmental
specifications.
Figure 2-19
WS-X6416-GBIC Ethernet Module Front Panel
Table 2-42
8
9
10
11
12
13
14
15
16
30694
7
LIN
K
6
LIN
K
5
LIN
K
4
LIN
K
3
LIN
K
2
LIN
K
1
LIN
K
16
16 PORT GIGABIT ETHERNET
LIN
K
15
14
LIN
K
13
12
LIN
K
11
10
LIN
K
9
8
LIN
K
7
6
LIN
K
5
4
LIN
K
3
2
LIN
K
1
LIN
K
ST
AT
US
WS-X6416-GBIC
WS-X6416-GBIC Features
Feature
Description
Ports per module
16
Connector type
SC or RJ-45 depending on the GBIC transceiver installed
Cabling distance
Depends on the GBIC transceiver installed in the module port. Refer to
Appendix B for descriptions of the GBIC transceiver types and
supported cabling distances.
Speed
1 Gbps
Buffer size
512 KB per port
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
•
Tx—1p2q2t
•
Rx—1p1q4t
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
32-Gbps shared bus
Forwarding architecture
Cisco Express Forwarding (CEF)
Module upgrades available
PoE support
Not supported.
Distributed forwarding
support
Not supported.
Pluggable transceivers
support
GBIC transceivers are supported. Refer to your software release notes
to determine which GBIC transceivers are supported. Refer to
Appendix B for additional information on the GBIC transceivers.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-53
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-42
WS-X6416-GBIC Features (continued)
Feature
Description
Digital Optical Monitoring
(DOM) support
Supported on some GBIC transceivers
Module front panel LEDs
STATUS
Refer to your software release notes for specific information on
which GBIC transceivers support DOM and the software
release required for support.
Note
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Note
•
Table 2-43
Off—The port is not active or the link is not connected.
WS-X6416-GBIC Ethernet Module Physical and Environmental Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
7.0 lb (3.17 kg)
Power requirement
(at 42 VDC)
2.81 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-54
OL-6265-02
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
WS-X6516-GBIC and WS-X6516A-GBIC
The WS-X6516-GBIC and the WS-X6516A-GBIC Ethernet modules (Figure 2-20) provide 16 1-Gbps
full- or half-duplex ports. Table 2-44 lists the module features, and Table 2-45 lists the module physical
and environmental specifications.
Figure 2-20
WS-X6516-GBIC and WS-X6516A-GBIC Ethernet Modules Front Panel
14
16
Table 2-44
3
4
5
6
LIN
K
2
LIN
K
1
7
8
9
10
11
12
13
14
15
16
44315
12
LIN
K
10
LIN
K
8
LIN
K
6
LIN
K
4
LIN
K
2
16 PORT GIGABIT ETHERNET
LIN
K
15
LIN
K
13
LIN
K
11
LIN
K
9
LIN
K
7
LIN
K
5
LIN
K
3
LIN
K
1
LIN
K
ST
AT
US
WS-X6516-GBIC
WS-X6516-GBIC and WS-X6516A-GBIC Features
Feature
Description
Ports per module
16
Connector type
SC or RJ-45 depending on the type of GBIC transceiver installed in the
module port
Cabling distance
Depends on the GBIC transceiver installed in the module port. Refer to
Appendix B for descriptions of the GBIC transceiver types and
supported cabling distances.
Speed
1 Gbps
Buffer size
•
512 KB per port—WS-X6516-GBIC
•
1 MB per port—WS-X6516A-GBIC
Maximum frame size
Up to 9216 bytes per frame (both modules)
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 2
•
Supervisor Engine 32
•
Supervisor Engine 720
Both modules:
•
Tx—1p2q2t
•
Rx—1p1q4t
Chassis/slot restrictions
No chassis or slot restrictions; the module can occupy any slot in any
Catalyst 6500 or Catalyst 6500-E chassis.
Bus connection
32-Gbps shared bus
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-55
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-44
WS-X6516-GBIC and WS-X6516A-GBIC Features (continued)
Feature
Description
Module upgrades available
PoE support
Not supported.
Distributed forwarding
support
Can be field-upgraded with either the WS-F6K-DFC,
WS-F6K-DFC3B, or WS-F6K-DFC3BXL daughter cards.
Refer to the Catalyst 6500 Series DFC, DFC3A, DFC3B, and
DFC3BXL Installation Note for additional information and field
upgrade procedures.
Pluggable transceivers
support
GBIC transceivers are supported. Refer to your software release notes
to determine which GBIC transceivers are supported. Refer to
Appendix B for additional information on the GBIC transceivers.
Digital Optical Monitoring
(DOM) support
Supported on some GBIC transceivers.
Module front panel LEDs
STATUS
Refer to your software release notes for specific information on
which GBIC transceivers support DOM and the software
release required for support.
Note
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Off—The port is not active or the link is not connected.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-56
OL-6265-02
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-45
WS-X6516-GBIC and WS-X6516A-GBIC Physical and Environmental Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
8.6 lb (3.9 kg)
Power requirement
(at 42 VDC)
WS-X6516-GBIC (base module)—3.40 A
WS-X6516A-GBIC (enhanced base module)—3.62 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-57
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
WS-X6724-SFP
The WS-X6724-SFP Ethernet module (Figure 2-21) provides 24 1-Gbps full- or half-duplex ports.
Table 2-46 lists the module features, and Table 2-47 lists the module physical and environmental
specifications.
Figure 2-21
24 PORT GIGABIT ETHERNET-SFP
99886
WS-X6724-SFP
WS-X6724-SFP Ethernet Module Front Panel
STATUS
Table 2-46
WS-X6724-SFP Ethernet Module Features
Feature
Description
Ports per module
24
Connector type
LC (optical) or RJ-45 (copper)
Cabling distance
Depends on the SFP transceiver installed in the module port. Refer to
Appendix B for descriptions of the SFP transceiver types and supported
cabling distances.
Speed
1 Gbps
Buffer size
•
Rx—166 kB per port
•
Tx—1.17 MB per port
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported by the Supervisor Engine 720 only.
Queues per port
•
Tx—1p3q8t
•
Rx—1q8t
Note
Rx is 2q8t when using dCEF.
Chassis/slot restrictions
The module is not supported in the Catalyst 6503 chassis.
Bus connection
Connects to the switch fabric using a single 20-Gbps channel.
Module upgrades available
PoE support
Not supported.
Distributed forwarding
support
Ships with the WS-F6700-CFC daughter card factory-installed. The
module can be upgraded in the field to support dCEF with the
installation of a dCEF daughter card (WS-F6700-DFC3A,
WS-F6700-DFC3B, or the WS-F6700-DFC3BXL).
Note
Pluggable transceivers
support
Refer to the Catalyst 6500 Series CFC, DFC3A, DFC3B, and
DFC3BXL Installation Note for additional information and
field upgrade procedures.
SFP transceivers are supported. Refer to your software release notes to
determine which SFP transceivers are supported. Refer to Appendix B
for additional information on the SFP transceivers.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-58
OL-6265-02
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-46
WS-X6724-SFP Ethernet Module Features (continued)
Feature
Description
Digital Optical Monitoring
(DOM) supported
Not supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Off—The port is not active or the link is not connected.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-59
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-47
WS-X6724-SFP Ethernet Module Physical and Environmental Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
Base module—8.8 lb (4.0 kg)
Base module + DFC daughter card—9.4 lb (4.3 kg)
Power requirement
(at 42 VDC)
•
WS-X6724-SFP (base module)—2.23 A
•
Base module + CFC daughter card (WS-F6700-CFC)—2.98 A
•
Base module + DFC3A daughter card (WS-F6700-DFC3A)—5.23 A
•
Base module + DFC3B daughter card (WS-F6700-DFC3B)—4.93 A
•
Base module + DFC3BXL daughter card (WS-F6700-DFC3BXL)—5.53 A
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-60
OL-6265-02
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
WS-X6748-SFP
The WS-X6748-SFP Ethernet module (Figure 2-22) provides 48 1-Gbps full- or half-duplex ports.
Table 2-48 lists the module features, and Table 2-48 lists the module physical and environmental
specifications.
Figure 2-22
48 PORT GIGABIT ETHERNET-SFP
144612
WS-X6748-SFP
WS-X6748-SFP Switching Module Front Panel
STATUS
Table 2-48
WS-X6748-SFP Features
Feature
Description
Ports per module
48
Connector type
LC (optical) or RJ-45 (copper)
Cabling distance
Depends on the SFP transceiver installed in the module port. Refer to
Appendix B for descriptions of the SFP transceiver types and supported
cabling distances.
Speed
1 Gbps
Buffer size
Rx—166 kB per port
Tx—1.17 MB per port
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported by the Supervisor Engine 720 only.
Queues per port
•
Tx—1p3q8t
•
Rx—1q8t
Note
Rx is 2q8t when using dCEF.
Chassis/slot restrictions
Can occupy any slot in any Catalyst 6500 or Catalyst 6500-E chassis
with the exception of the Catalyst 6513 chassis where the module can
occupy only slots 9 through 13.
Bus connection
Connects to the switch fabric using dual 20-Gbps channels.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-61
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-48
WS-X6748-SFP Features (continued)
Feature
Description
Module upgrades available
PoE support
Not supported.
Distributed forwarding
support
Ships with the WS-F6700-CFC daughter card factory-installed. The
module can be upgraded in the field to support dCEF with the
installation of a dCEF daughter card (WS-F6700-DFC3A,
WS-F6700-DFC3B, or the WS-F6700-DFC3BXL).
Refer to the Catalyst 6500 Series DFC3A, DFC3B, and
DFC3BXL Installation Note for additional information and
field upgrade procedures.
Note
Pluggable transceivers
support
SFP transceivers are supported. Refer to your software release notes to
determine which SFP transceivers are supported. Refer to Appendix B
for additional information on the SFP transceivers.
Digital Optical Monitoring
(DOM) support
Not supported.
Module front panel LEDs
STATUS
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Off—The port is not active or the link is not connected.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-62
OL-6265-02
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-49
WS-X6748-SFP Physical and Environmental Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
Base module with CFC daughter card (WS-F6700-CFC) installed—9.0 lb (4.1 kg)
Base module with DFC daughter card WS-F6700-DFC installed—10.8 lb (4.5 kg)
Power requirement
(at 42 VDC)
•
WS-X6748-SFP (base module)—5.32 A
•
Base module + CFC daughter card WS-X6700-CFC)—6.07 A
•
Base module + DFC3A daughter card (WS-F6700-DFCA)—8.32 A
•
Base module + DFC3B daughter card (WS-F6700-DFC3B)—8.02 A
•
Base module + DFC3BXL daughter card (WS-F6700-DFC3BXL)—8.62 A
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-63
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
WS-X6816-GBIC
The WS-X6816-GBIC Ethernet module (Figure 2-23) provides 16 1-Gbps full- or half-duplex ports.
Table 2-50 lists the module features, and Table 2-51 lists the module physical and environmental
specifications.
Figure 2-23
WS-X6816-GBIC Switching Module Front Panel
14
16
Table 2-50
3
4
5
6
LIN
K
2
LIN
K
1
7
8
9
10
11
12
13
14
15
16
52719
12
LIN
K
10
LIN
K
8
LIN
K
6
LIN
K
4
LIN
K
2
16 PORT GIGABIT ETHERNET
LIN
K
15
LIN
K
13
LIN
K
11
LIN
K
9
LIN
K
7
LIN
K
5
LIN
K
3
LIN
K
1
LIN
K
ST
AT
US
WS-X6816-GBIC
WS-X6816-GBIC Ethernet Module Features
Feature
Description
Ports per module
16
Connector type
SC (optical) or RJ-45 (copper)
Cabling distance
Depends on the GBIC transceiver installed in the module port. Refer to
Appendix B for supported GBIC transceiver types and cabling
distances.
Speed
1 Gbps
Buffer size
•
Tx—1.17 MB per port
•
Rx—166 kB per port
Maximum frame size
Up to 9216 bytes per frame
Supervisor engine support
Supported by the following supervisor engines:
Queues per port
•
Supervisor Engine 2 (requires a Switch Fabric Module or SFM2 be
installed in the switch chassis and a DFC3 daughter card installed
on the WS-X6816-GBIC)
•
Supervisor Engine 720 (requires a DFC3A, DFC3B, or DFC3BXL
daughter card be installed on the module)
•
Tx—1p2q2t
•
Rx—1p1q4t
Note
Rx is 2q8t when using dCEF.
Chassis/slot restrictions
Can occupy any slot in any Catalyst 6500 or Catalyst 6500-E chassis
with the exception of the Catalyst 6513 chassis where the module can
occupy only slots 9 through 13.
Bus connection
Connects to the switch fabric using dual 20-Gbps channels.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-64
OL-6265-02
Chapter 2
Ethernet Switching Modules
1-Gigabit Ethernet Modules
Table 2-50
WS-X6816-GBIC Ethernet Module Features (continued)
Feature
Description
Module upgrades available
PoE support
Not supported.
Distributed forwarding
support
Can be upgraded in the field to support dCEF with the installation of a
DFC daughter card (WS-F6700-DFC3A, WS-F6700-DFC3B, or the
WS-F6700-DFC3BXL).
Refer to the Catalyst 6500 Series DFC3A, DFC3B, and
DFC3BXL Installation Note for additional information and
field upgrade procedures.
Note
Pluggable transceivers
support
GBIC transceivers are supported. Refer to your software release notes
to determine which GBIC transceivers are supported. Refer to
Appendix B for additional information on the GBIC transceivers.
Digital Optical Monitoring
(DOM) support
Supported on some GBIC transceivers.
Module front panel LEDs
STATUS
Refer to your software release notes for specific information on
which GBIC transceivers support DOM and the software
release required for support.
Note
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Off—The port is not active or the link is not connected.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-65
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
Table 2-51
WS-X6816-GBIC Physical and Environmental Specifications
Item
Specification
Dimensions (H x W x D)
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis.
Weight
Base module—9.2 lb (4.2 kg)
Power requirement
(at 42 VDC)
Environment
•
WS-X6816-GBIC (base module)—3.84 A
•
Base module + DFC daughter card (WS-F6K-DFC)—5.94 A
•
Base module + DFC daughter card (WS-F6K-DFC3B)—5.51 A
•
Base module + DFC daughter card (WS-F6K-DFC3BXL)—6.22 A
11.2 lb (5.08 kg)
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)
10-Gigabit Ethernet Modules
This section describes the following 10-Gigabit Ethernet modules:
•
WS-X6704-10GE Ethernet Module, page 2-67
•
WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet Modules, page 2-70
•
WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Modules, page 2-73
Catalyst 6500 Series Ethernet Modules Installation Guide
2-66
OL-6265-02
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
WS-X6704-10GE Ethernet Module
The WS-X6704-10GE Ethernet module (Figure 2-24) provides 4 10-Gbps full- or half-duplex ports.
Table 2-52 lists the module features, and Table 2-53 lists the module physical and environmental
specifications.
Figure 2-24
WS-X6704-10GE Ethernet Module Front Panel
WS-X6704-10GE
PORT 1
RX
TX
PORT 2
RX
TX
PORT 3
RX
TX
PORT 4
RX
99885
4
LIN
K
3
K
K
LIN
LIN
LIN
K
2
1
ST
AT
US
TX
4 PORT 10 GIGABIT ETHERNET
Table 2-52
WS-X6704-10GE Ethernet Module Features
Feature
Description
Ports per module
4
Connector type
SC or InfiniBand 4X depending on the type of XENPAK transceiver
installed in the module.
Cabling distance
Depends on the XENPAK transceiver installed in the module port.
Refer to Appendix B for supported XENPAK transceiver types and
cabling distances.
Speed
10 Mbps
Buffer size
16 MB
Maximum frame size
Up to 9216 bytes
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 720
•
Tx—1p7q8t (CoS to queue)
•
Rx—1q8t (when using dCEF); 8q8t (CoS to queue)
Chassis/slot restrictions
Not supported on the Catalyst 6503 chassis. Support on the
Catalyst 6513 chassis is restricted to slots 9 through 13.
Bus connection
Dual 20-Gbps serial channel connections to the switch fabric.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-67
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
Table 2-52
WS-X6704-10GE Ethernet Module Features (continued)
Feature
Description
Module upgrades available
PoE support
Not supported.
Distributed forwarding
support
Ships with the WS-F6700-CFC daughter card factory-installed. Can be
upgraded in the field to support dCEF with the installation of a DFC
daughter card (WS-F6700-DFC3A, WS-F6700-DFC3B, or the
WS-F6700-DFC3BXL).
Refer to the Catalyst 6500 Series DFC3A, DFC3B, and
DFC3BXL Installation Note for additional information and
field upgrade procedures.
Note
Pluggable transceivers
support
XENPAK transceivers are supported. Refer to your software release
notes to determine which XENPAK transceivers are supported. Refer to
Appendix B for additional information on the XENPAK transceivers.
Digital Optical Monitoring
(DOM) support
Supported on some XENPAK transceivers.
Module front panel LEDs
STATUS
Refer to your software release notes for specific information on
which XENPAK transceivers support DOM and the software
release required for support.
Note
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Off—The port is not active or the link is not connected.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-68
OL-6265-02
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
Table 2-53
WS-X6704-10GE Ethernet Module Specifications
Item
Specification
Dimensions
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the
chassis.
Weight
Base module + CFC daughter card (WS-F6700-CFC)—9.0 lb (4.08 kg)
Power requirement
(at 42 VDC)
WS-X6704-10GE (base module + CFC daughter card)—7.03 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to
3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-69
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet Modules
The WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet module (Figure 2-25) provides 8 10-Gbps
full- or half-duplex ports. Table 2-52 lists the module features, and Table 2-53 lists the module physical
and environmental specifications.
WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet Module Front Panel
184597
Figure 2-25
Note
Table 2-54
Both of the modules (WS-X6708-10G-3C and WS-X6708-10G-3CXL) are identified on the faceplate as
WS-X6708-10GE.
WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet Module Features
Feature
Description
Ports per module
8
Connector type
SC or CX4 depending on the type of X2 transceiver installed in the
module.
Cabling distance
Depends on the X2 transceiver installed in the module port. Refer to
Appendix B for supported X2 transceiver types and cabling distances.
Speed
10 Mbps
Buffer size
128 MB per port
Maximum frame size
Up to 9216 bytes
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
Chassis/slot restrictions
Bus connection
•
Supervisor Engine 720
•
Tx—1p7q4t
•
Rx—8q4t
•
Not supported in the Catalyst 6503 chassis.
•
Supported only in slots 9–13 in the Catalyst 6513 chassis.
•
When the WS-X6708-10G module is installed in a Catalyst 6500-E
series chassis or a Catalyst 6500-NEB- A chassis, the configuration
is NEBS 3 compliant (chassis supports operating temperatures up
to 55°C).
•
When the WS-X6708-10G module is installed in a Catalyst 6500
non-E series chassis that is equipped with a fan tray 2 and a
2500 W or larger power supply, the configuration is not NEBS 3
compliant (chassis supports operating temperatures up to 40°C
only).
Dual 20-Gbps serial channel connections to the switch fabric.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-70
OL-6265-02
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
Table 2-54
WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet Module Features (continued)
Feature
Description
Module upgrades available
PoE support
Distributed forwarding
support
Pluggable transceivers
support
Not supported.
•
WS-X6708-10G-3C comes factory-equipped with a DFC3C
daughter card.
•
WS-X6708-10G-3CXL comes factory-equipped with a DFC3CXL
daughter card.
X2 transceivers are supported. Not all types of X2 transceivers may be
supported. Refer to your software release notes to determine which X2
transceivers are currently supported. Refer to Appendix B for
additional information on the X2 transceivers.
Only X2 transceivers with part number revision -02 or later are
supported on this module. Check the part number label on the
X2 transceiver to verify its usability.
Note
Digital Optical Monitoring
(DOM) support
Supported on some X2 transceivers.
Module front panel LEDs
STATUS
Refer to your software release notes for specific information on
which X2 transceivers support DOM and the software release
required for support.
Note
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Off—The port is not active or the link is not connected.
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-71
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
Table 2-55
WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet Module Specifications
Item
Specification
Dimensions
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the
chassis.
Weight
16.0 lb (7.26 kg)
Power requirement
(at 42 VDC)
WS-X6708-10G-3C (base module + the DFC3C daughter
card)—10.58 A
WS-X6708-10G-3CXL (base module + the DFC3CXL daughter
card)—11.28 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to
3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
2-72
OL-6265-02
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Modules
The WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet modules (Figure 2-26) provide 16
10-Gbps full- or half-duplex ports. Table 2-56 lists the module features, and Table 2-57 lists the module
physical and environmental specifications.
WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Module Front Panel
186704
Figure 2-26
Note
Table 2-56
Both of the modules (WS-X6716-10G-3C and WS-X6716-10G-3CXL) are identified on the faceplate as
WS-X6708-10GE.
WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Module Features
Feature
Description
Ports per module
16
Connector type
SC or CX4 depending on the type of X2 transceiver installed in the
module.
Cabling distance
Depends on the X2 transceiver installed in the module port. Refer to
Appendix B for supported X2 transceiver types and cabling distances.
Speed
10 Mbps
Buffer size
Oversubscription mode—90 MB per port group
Performance mode—200 MB per port
Maximum frame size
Up to 9216 bytes
Supervisor engine support
Supported on the following supervisor engines:
Queues per port
•
Supervisor Engine 720
•
Supervisor Engine 720-10G
•
Oversubscription mode:
– Tx—1p7q4t per port group
– Rx—1p7q2t per port
•
Performance mode:
– Tx—1p7q4t per port
– Rx—8q4t per port
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-73
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
Table 2-56
WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Module Features (continued)
Feature
Description
Chassis/slot restrictions
•
Not supported in the Catalyst 6503 chassis.
•
Supported only in slots 9–13 in the Catalyst 6513 chassis.
•
When the WS-X6708-10G module is installed in a Catalyst 6500-E
series chassis or a Catalyst 6509-NEB-A chassis, the configuration
is NEBS 3 compliant (chassis supports operating temperatures up
to 55°C).
•
When the WS-X6708-10G module is installed in a Catalyst 6500
non-E series chassis that is equipped with a fan tray 2 and a
2500 W or larger power supply, the configuration is not NEBS 3
compliant (chassis supports operating temperatures up to 40°C
only).
Switch fabric connection
40-Gbps (80-Gbps full-duplex)
Oversubscription
4:1
Module upgrades available
PoE support
Distributed forwarding
support
Pluggable transceivers
support
Not supported.
•
WS-X6716-10G-3C comes factory-equipped with a DFC3C
daughter card.
•
WS-X6716-10G-3CXL comes factory-equipped with a DFC3CXL
daughter card.
X2 transceivers are supported. Not all types of X2 transceivers may be
supported. Refer to your software release notes to determine which X2
transceivers are currently supported. Refer to Appendix B for
additional information on the X2 transceivers.
Note
Only X2 transceivers with part number revision -02 or later are
supported on this module. Check the part number label on the
X2 transceiver to verify its usability.
Catalyst 6500 Series Ethernet Modules Installation Guide
2-74
OL-6265-02
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
Table 2-56
WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Module Features (continued)
Feature
Description
Digital Optical Monitoring
(DOM) support
Supported on some X2 transceivers.
Module front panel LEDs
STATUS
Refer to your software release notes for specific information on
which X2 transceivers support DOM and the software release
required for support.
Note
•
Green—All diagnostics pass; the module is operational.
•
Orange—The module is booting or running diagnostics; an
overtemperature condition has occurred.
LINK
•
Green—The port is active (the link is connected and operational).
•
Flashing orange—The port failed diagnostics and is disabled.
•
Orange—The port is disabled.
•
Red—The module is resetting; an overtemperature condition has
occurred.
Note
•
Table 2-57
If the module fails to download code and configuration
information successfully during the initial reset, the LED stays
red; the module does not come online.
Off—The port is not active or the link is not connected.
WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Module Specifications
Item
Specification
Dimensions
1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the
chassis.
Weight
13.0 lb ( kg) (Excludes weight of X2 transceivers)
Power requirement
(at 42 VDC)
WS-X6716-10G-3C (base module + the DFC3C daughter
card)—10.9 A
WS-X6716-10G-3CXL (base module + the DFC3CXL daughter
card)—11.6 A
Environment
Operating temperature
Humidity (RH) ambient
(noncondensing)
Operating altitude
•
Certified for operation: 32° to 104°F (0° to 40°C)
•
Designed and tested for operation: 32° to 130°F (0° to 55°C)
10 to 90%
•
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•
Designed and tested for operation: –200 to 10,000 ft (–60 to
3000 m)
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-02
2-75
Chapter 2
Ethernet Switching Modules
10-Gigabit Ethernet Modules
Catalyst 6500 Series Ethernet Modules Installation Guide
2-76
OL-6265-02