Download Atdec TH-WH-PJ-CM
Transcript
G Attaching the Ceiling Mount Assembly to the Ceiling Hanger G.1. Connect the Shaft to the Bottom Ceiling Hanger as shown below. Bottom Ceiling Hanger Shaft Locking Hook M8x50mm Socket Cap Screw universal projector Ceiling mount WARNING: This bracket supports up to 15kg (33lbs). DO NOT overload this bracket. Component Checklist Ceiling Mount Assembly (x1) Mounting Plate (x1) Ceiling Mount and Projector G.2. Insert the Locking Hook into the slot in the Bottom Ceiling Hanger to lock the Ceiling Mount Assembly. Extension Brackets 150mm (x2) Locking Hook Bits Bag Extension Brackets 100mm (x2) 6mm Allen Key H TELEHOOK Please read these instructions before commencing installation as faulty installation could result in injury. Atdec assumes no responsibility for faulty installations. G.3. Tighten the Locking Hook with the supplied M8x50mm Socket Cap Screw and the M8 Nyloc Nut. M8 Nyloc Nut Installation Instructions IMPORTANT Tip: When the projector requires servicing, remove the projector via this easy disconnection point to save time. Extension Brackets 50mm (x2) Top Ceiling Hanger (x1) Mid Ceiling Hanger (x1) Extension Brackets 75mm (x2) Fixing Coupler (x1) M5x10mm Socket Button Cap Screw (x4) Square Nut (x8) Bottom Ceiling Hanger (x1) Pitch Adjustment 6mm Allen Key M8x65mm Screw Loosen 6mm Allen Key Roll Loosen Bottom Spacer (x4) M8 Nyloc Nut (x8) M8x50mm Socket Head Cap Screw (x8) All bolts and screws must be used at the designated points in the installation instructions to prevent damage to the projector, or personal injury. DO NOT install near air conditioner vents or where there is excessive dust or smoke. Ensure the projector is mounted so that it is not possible for excessive loads to be placed on the bracket. Pitch Pitch a Component Checklist Check you have received all parts against the Component Checklist above. Shift To make Roll/Shift adjustments, first ensure the weight of the projector is supported. Then loosen the M8x65mm Screw with the supplied 6mm Allen Key, and adjust to your desired position. Re-tighten the screw firmly. Spacer Large (x4) Medium (x4) Small (x4) Ensure the Ceiling can support the total weight of the Projector and the Universal Ceiling Mount. M8x15mm Screw Tighten Roll 14 Gauge Coach Screw (x4) WARNING 6mm Allen Key Tighten Washer 20mm (x4) 10mm (x4) 8mm (x4) Nylon Anchor Plug (x4) 3mm Allen Cross Recessed Screws Key (x1) M2.5x15 (x4) M3x15 / M3x20 (x4 each) M4x15 / M4x20 / M4x25 (x4 each) M5x15 / M5x20 / M5x25 (x4 each) M6x15 / M6x20 / M6x25 (x4 each) Adjusting the Projector Roll / Shift Adjustment 6mm Allen Key (x1) To make Pitch adjustment, first ensure the weight of the projector is supported. Then loosen both M8x15mm Screws with the supplied 6mm Allen Key, and adjust to your desired position. Re-tighten both screws firmly. b Assembling the Mounting Plate and the Fixing Coupler Assemble the Mounting Plate and the Fixing Coupler as shown, then move onto the next step to attach it to the ceiling. Installation Complete Mounting Plate Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 22.03.07© Fixing Coupler NOTE If mounting onto an angled ceiling, ensure the Fixing Coupler is in the correct orientation. angled ceiling Fixing Coupler C Installing the Ceiling Plate F Choose the appropriate installation procedure depending on your ceiling type. Masonry F.1. Loosen the M5x10mm Screws using the supplied 3mm Allen Key until you can slide the extension brackets freely, as shown. Plaster Board Use the recommended mounting hole pattern shown: Use the recommended mounting hole pattern shown: 3mm (1/8 ”) Holes 8mm (5/16”) Holes Mounting Plate Timber Beam Nylon Anchor Plug Masonry Ceiling 14 Gauge Coach Screw D Mounting Plate 14 Gauge Coach Screw Tighten Tighten NOTE: Ensure the screws are securely fixed into the Timber Beam You may need to replace the attached Extension Brackets with the additional longer brackets supplied in the package, to suit the mounting hole configuration of your projector. 3mm Allen Key Extension Bracket M5x10mm Socket Button Cap Screw F.2. Place the Ceiling Mount Assembly over the Projector and align the centre of the Ceiling Mount with the Centre of Gravity marked previously on the Projector. Centre of Ceiling Mount Centre of Gravity Attaching the Ceiling Hangers to the Fixing Coupler D.1. Install the Ceiling Hangers to the required height as shown in the following diagrams. D.2. Top Ceiling Hanger Mounting Plate M8 Nyloc Nut Top Ceiling Hanger 6mm Allen Key M8x50mm Socket Head Cap Screw F.3. Place the Bottom Spacers in between the Extension Brackets and the Projector, and align the mounting holes as shown below. D.3. Mid Ceiling Hanger Fixing Coupler E Plaster Board 20mm Washer Washer Attaching the Ceiling Mount Assembly to the Projector M8x50mm Socket Head Cap Screw M8 Nyloc Nut Bottom Ceiling Hanger M8 Nyloc Nut 6mm Allen Key M8x50mm Socket Head Cap Screw Cable Management Option 6mm Allen Key Mid Ceiling Hanger projector cables Feed the projector cables through the slot on the Bottom Ceiling Hanger as shown. Centre of Gravity Step 1 Step 2 E.2. Repeat this process for the perpendicular side (follow Step 2) E.3. Where both balance points meet is the Centre of Gravity of your projector. Use a pencil to mark this point. Extension Bracket Extension Bracket Bottom Spacer Bottom Spacer Recessed Mounting Hole Spacer Mounting Hole Finding the Centre of Gravity of the Projector E.1. Pick up the projector using both of your index fingers. Move your fingers along the side of the Projector (follow Step 1) until it is level. Remember the balance point. Bottom Spacers NOTE If your mounting holes are recessed into the projector, you may need to use the additional Spacers supplied in the Bits Bag. Please select the appropriate Spacers according to the design of your projector. F.4. Select the correct Mounting Screws from the Bits Bag and firmly screw the Ceiling Mount Assembly onto your Projector. Once this is done, the Projector Ceiling Mount Assembly is ready to be mounted onto the Bottom Ceiling Hanger. Step 2 Step 1 Mounting Screws Bottom Spacer