Download Universal Remote Control RNC-100 Operating instructions
Transcript
OPERATING INSTRUCTIONS RD-8601 Audio/Video Receiver Introduction This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Note to CATV System Installer : This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FOR YOUR SAFETY Units shipped to the U.S.A and Canada are designed for operation on 120 V AC only. Safety precaution with use of a polarized AC plug. However, some products may be supplied with a nonpolarized plug. U.S.A CANADA 120 V CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert. ATTENTION • • • • • • • • : Pour éviter chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’ au fond. Avoid high temperatures. Allow for sufficient heat dispersion when installed on a rack. Keep the set free from moisture, water, and dust. Do not let foreign objects in the set. Handle the power cord carefully. Hold the plug when unplugging the cord. Unplug the power cord when not using the set for long periods of time. Do not obstruct the ventilation holes. Do not let insecticides, benzene, and thinner come in contact with the set. Never disassemble or modify the set in any way. 2 ENGLISH READ THIS BEFORE OPERATING YOUR UNIT ENGLISH SAFETY INSTRUCTION 1. Read Instructions - All the safety and operating instructions should be read before the product is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement, or near a swimming pool; and the like. 8. Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. 9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. PORTABLE CART WARNING The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 11. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Alternate Warnings - This product is equipped with a three-wire grounding-type plug, a plug having a third(grounding) pin. This plug will only fit into a grounding-type power outlet. this is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure 1. Figure 1 Example of antenna grounding as per National Electrical Code, ANSI/NFPA 70 ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) NEC - NATIONAL ELECTRICAL CODE 15. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 19. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service - Unplug this product form the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance - this indicates a need for service. 21. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 24. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 3 CONTENTS Introduction | 2 ENGLISH • READ THIS BEFORE OPERATING YOUR UNIT • SAFETY INSTRUCTION | 3 System Connections | 5 Front Panel Controls | 11 Universal Remote Controls | 13 • OPERATING COMPONENTS WITH REMOTE CONTROL • REMOTE CONTROL OPERATION RANGE | 15 • LOADING BATTERIES | 15 • USING FUNCTIONS OF REMOTE CONTROL | 16 | 15 Speaker Setup | 19 • SETTING THE SPEAKER SETUP MANUALLY | 20 • SETTING THE SPEAKER SETUP AUTOMATICALLY (AUTO SPEAKER SETUP) Operations • LISTENING TO A PROGRAM SOURCE | 25 • SURROUND SOUND | 28 • ENJOYING SURROUND SOUND | 30 • LISTENING TO RADIO BROADCASTS | 35 • RECORDING | 37 • DIGITAL AUDIO RECORDING WITH MD RECORDER • OTHER FUNCTIONS | 39 | 38 Using the OSD • CURRENT STATUS DISPLAY | 40 OSD Menu Settings | 40 • SETTING THE SPEAKER SETUP | 42 • SELECTING THE FUNCTION | 45 • SELECTING THE SURROUND MODE | 47 • SETTING THE CH LEVEL SETUP | 48 Troubleshooting Guide | 50 Specifications | 51 Setup Code Table | 52 4 | 22 • Do not plug the AC input cord into the wall AC outlet until all connections are completed. • Be sure to observe the color coding when connecting audio, video and speaker cords. • Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver. 1 7 5 2 11 ANTENNA VIDEO VIDEO S-VIDEO DIGITAL OUT 1 IN MONITOR OUT VIDEO 1 9 SUB WOOFER CENTER VIDEO 2 VIDEO 1 OPT 2 OPTICAL PRE OUT SUB WOOFER EXTERNAL IN SETUP MIC VIDEO 1 VIDEO 2 OPT 1 GND AM LOOP COMPONENT VIDEO IN IN IN FM 75 COAX OUT 2 MONITOR ENGLISH System Connections IN 3 PLAY CD REC TAPE AUX FRONT SURROUND SURROUND VIDEO 1 IN BACK VIDEO 1 OUT VIDEO 2 4 DIGI-LINK FRONT SPEAKERS (6 ) 6 SURROUND SPEAKERS (6 ) CENTER SPEAKER (6 ) SURROUND BACK (6 ) 10 8 1. CONNECTING ANTENNAs FM Outdoor Antenna FM Indoor Antenna ANTENNA ANTENNA FM 75 FM 75 GND AM LOOP GND AM LOOP • A 75Ω outdoor FM antenna may be used to further improve the reception. Disconnect the indoor antenna before replacing it with the outdoor one. • Change the position of the FM indoor antenna until you get the best reception of your favorite FM stations. AM Outdoor Antenna ANTENNA FM 75 AM Loop Antenna GND AM LOOP • Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set it to a direction for the best reception. • If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of the AM loop antenna. 5 2. CONNECTING VIDEO COMPONENTS VIDEO 2 DVD player, etc. VIDEO 1 Video deck, DVD recorder, etc. R OUT L ENGLISH COMPONENT Y OUT CB AUDIO (COMPOSITE) VIDEO OUT CR S-VIDEO OUT Y COMPONENT CB OUT CR AUDIO OUT AUDIO (COMPOSITE) S-VIDEO IN VIDEO R R L L IN OUT IN OUT VIDEO VIDEO S-VIDEO IN VIDEO 1 COMPONENT VIDEO IN MONITOR IN OUT VIDEO 2 VIDEO 1 VIDEO 1 VIDEO 2 OUT VIDEO 1 IN MONITOR VIDEO 1 OUT VIDEO 1 OUT VIDEO 2 CR S-VIDEO IN (COMPOSITE) VIDEO IN MONITOR CB Y COMPONENT IN TV, Projector, etc. • There are three types of video jacks(COMPONENT, S-VIDEO, (composite) VIDEO) for connecting video components. Connect them to the corresponding video jacks according to their capability. • For your reference, the excellence in picture quality is as follows : “COMPONENT” > “S-VIDEO” > “(composite) VIDEO”. • When making COMPONENT VIDEO connections, connect “Y” to “Y”, “PB/CB” to “CB”(or “B-Y”, “PB”) and “PR/CR” to “CR”(or “RY”, “PR” ). • When connecting to video recording component such as video deck, DVD recorder, etc., you must use the same type of video jacks that you did connect to video playback components such as DVD player, LD player, etc. • This unit is equipped with a function that up-converts composite video or S-Video signals to component video signals or downconverts S-Video signals to composite video signals and outputs them from the MONITOR OUTs. Because of this, one of three types of MONITOR OUT jacks can be connected to the monitor TV regardless of how the video components are connected to VIDEO IN jacks of this unit. • Connect the video components, referring to the following table. Relationship between the video input signal and video output signal MONITOR OUTs Video input signals COMPONENT S-VIDEO × × × (COMPOSITE) VIDEO × × × × × × COMPONENT S-VIDEO (COMPOSITE) VIDEO Composite video Composite video Composite video S-Video S-Video S-Video S-Video S-Video Composite video Component × × Component Composite video Composite video Component S-Video S-Video Component S-Video Composite video Notes : • In such a case of making only COMPONENT VIDEO connections between this receiver and video component, while viewing a movie via MONITOR COMPONENT OUTs, if the OSD menu operation is performed with the OSD, CURSOR control(▲, ▼, ◀, ▶), ENTER buttons, etc., the picture is automatically turned off and only the OSD menu is displayed. • When S-Video signals and composite video signals are input into this receiver, even though the OSD menu operation is performed, the OSD menu cannot be displayed via MONITOR COMPOSITE OUT. • When Sherwood DVD player such as V-768, etc. is connected to the DIGI-LINK jack for system control, you should connect the DVD player to the “ VIDEO 2” jacks of this unit. Because, if the PLAY button, etc. is pressed on the DVD player, the VIDEO 2 is automatically selected as an input source on this unit. Then playback, etc. starts. 6 3. CONNECTING AUDIO COMPONENTS ENGLISH • The AUX jacks may be connected to an additional audio component such as a CD player, a tape deck, etc. TAPE Tape deck, MD recorder, etc. L AUDIO R OUT L R CD AUDIO IN AUX CD player AUDIO L OUT R L R PLAY CD other audio component AUDIO OUT REC TAPE AUX 4. CONNECTING EXTERNAL INs EXTERNAL IN SUB WOOFER CENTER • Use these jacks to connect the corresponding outputs of a DVD player or external decoder, etc. that has 6 or 7 channel analog audio outputs • In case of 6 channel outputs, do not connect this SURROUND BACK input to your audio component.(For details, refer to the operating instructions of the component to be connected.) FRONT L R CENTER FRONT SURROUND R SURROUND BACK L BACK SURROUND SUBWOOFER 7 CH AUDIO OUTPUT Decoder with 6 or 7 channel outputs 5. CONNECTING DIGITAL INs and OUT • The OPTICAL and the COAXIAL DIGITAL OUTs of the components that are connected to CD and VIDEO 1~ VIDEO 3 of this unit can be connected to these DIGITAL INs. • A digital input should be connected to the components such as a CD player, LD player, DVD player, etc. capable of outputting DTS Digital Surround, Dolby Digital or PCM format digital signals, etc. • If the component with OPTICAL IN jack is connected to the OPTICAL OUT jack of this unit, you can record the high quality sound of CDs, etc. without degradation. • For details, refer to the operating instructions of the component connected. • When making the COAXIAL DIGITAL connection, be sure to use a 75 Ω COAXIAL cord, not a conventional AUDIO cord. • All of the commercially available optical fiber cords cannot be used for the equipment. If there is an optical fiber cord which cannot be connected to your equipment, consult your dealer or nearest service organization. Note : • Be sure to make either a OPTICAL or a COAXIAL DIGITAL connection on each component. (You don’t need to do both.) 7 DIGITAL IN OPT 1 Component with OPTICAL DIGITAL OUT OPT 2 Component with OPTICAL DIGITAL OUT OPTICAL Component such as an MD recorder, CD recorder with OPTICAL DIGITAL IN OUT 1 COAX 2 IN Component with COAXIAL DIGITAL OUT Component with COAXIAL DIGITAL OUT 6. CONNECTING SYSTEM CONTROL • Connect this jack to the DIGI LINK jack of the external Sherwood component that uses the DIGI LINK II or III remote control system. Sherwood component with DIGI LINK II or III System control cord Tape deck DIGI-LINK DVD player 7. SUBWOOFER PREOUT connection • To emphasize the deep bass sounds, connect a powered subwoofer. PRE OUT SUB WOOFER Powered subwoofer 8. CONNECTING SPEAKERS • Be sure to connect speakers firmly and correctly according to the channel(left and right) and the polarity(+ and -). If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connection is incorrect, the sound will be unnatural and lack bass. • For installing the speakers, refer to “Speaker placement” on page 9. • After installing the speakers, first adjust the speaker settings according to your environment and speaker layout.(For details, refer to “Speaker Setup” on page 19.) Front right (Front) Center Front left Caution : • Be sure to use the speakers with the impedance of 6 ohms or above. • Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers. FRONT SPEAKERS (6 ) SURROUND SPEAKERS (6 ) CENTER SPEAKER (6 ) Surround Surround left right 8 SURROUND BACK (6 ) Surround back ENGLISH CD player Speaker placement ENGLISH Ideal speaker placement varies depending on the size of your room and the wall coverings, etc. The typical example of speaker placement and recommendations are as follows : TV or SCREEN 1 SUBWOOFER ■Front left and right speakers and center speaker FRONT (LEFT) • Place the front speakers with their front surfaces as flush with TV or monitor screen as possible. • Place the center speaker between the front left and right speakers and no further from the listening position than the front speakers. • Place each speaker so that sound is aimed at the location of the listener’s ears when at the main listening position. 3 CENTER 4 FRONT (RIGHT) 5 2 LISTENING POSITION 6 ■Surround left and right speakers • Place the surround speakers approximately 1 meter (40 inches) above the ear level of a seated listener on the direct left and right of them or slightly behind. 7 SURROUND (LEFT) SURROUND (RIGHT) 9 8 ■Surround back speaker • Place the surround back speaker at the rear center facing the front at a slightly higher position (0 to 10 inches) than the surround speakers. • We recommend installing the surround back speaker at a slightly downward facing angle. This effectively prevents the surround back channel signals from reflecting off the TV or screen at the front center, resulting in interference and making the sense of movement from the front to the back less sharp. SURROUND BACK Surround speaker Surround back speaker Point slightly downward Front speaker ■Subwoofer • The subwoofer reproduces powerful deep bass sounds. Place a powered subwoofer anywhere in the front as desired. ■Notes : • When using a conventional TV , to avoid interference with the TV picture, use only magnetically shielded front left and right and center speakers. • To obtain the best surround effects, the speakers except the subwoofer should be full range speakers. 9 60 to 90 cm 9. CONNECTING MICROPHONE Note: • Because the microphone for Auto Speaker Setup is designed for use with this receiver, do not use a microphone other than the one supplied with this receiver. 10. SWITCHED AC OUTLETs • Theses outlets are switched on(power-on mode) and off(standby mode) according to power control as follows(Maximum total capacity is 100 W, 1 A). Standby mode - Switched AC outlet off Power-on mode - Switched AC outlet on 11. AC INPUT CORD • Plug this cord into a wall AC outlet. 10 ENGLISH • To use Auto Speaker Setup function, connect the microphone to the SETUP MIC jack.(For details, refer to “SETTING THE SPEAKER SETUP AUTOMATICALLY(AUTO SPEAKER SETUP)” on page 22.) SETUP MIC Microphone Front Panel Controls ENGLISH 23 24 26 25 21 20 AUDIO/VIDEO RECEIVER RD-8601 MASTER VOLUME POWER REMOTE SENSOR 1 ON/ 2 22 OFF INPUT SELECTOR STANDBY AUDIO VIDEO SURROUND MODE EXTERNAL IN AUTO DSP MODE STEREO PARAMETER DIGITAL INPUTS ON/STANDBY 27 16 3 VIDEO 3 PHONES CHANNEL SELECTOR SPEAKER ADJUST TONE MODE SPEAKER SETUP DYNAMIC RANGE CINEMA EQ MEMO/ENTER TUNING/PRESET T/P MODE FM MODE BAND ON/OFF VIDEO 4 5 6 7 8 9 10 11 1. POWER switch 2. STANDBY button/indicator 3. HEADPHONE jack 4. SPEAKER button/indicator 5. CHANNEL SELECTOR button 6. ADJUST UP/DOWN(▲/▼) buttons 7. TONE MODE button 8. SPEAKER SETUP button 9. DYNAMIC RANGE button 10. CINEMA EQ button 11. MEMORY/ENTER button 12. TUNING/PRESET UP/DOWN(▲/▼) buttons 13. TUNING/PRESET MODE button 14. FM MODE button 15. BAND button 19 13 14 15 12 L - AUDIO - R 16. AUTO button 17. DSP MODE UP/DOWN(▶/◀) buttons 18. STEREO button 19. VIDEO 3 INPUT jacks - For details, see next page. 20. PARAMETER button 21. DIGITAL INPUTS button 22. MASTER VOLUME CONTROL knob 23. FLUORESCENT DISPLAY - For details, see below. 24. REMOTE SENSOR 25. AUDIO INPUT SELECTOR button 26. VIDEO INPUT SELECTOR button 27. EXTERNAL IN button ■ FLUORESCENT DISPLAY 2 11 HVS 10 9 ST TUNED dB kHz 8 7 PRESET MEM MHz DTS ES 96 24 NEO:6 MPEG 1 D EX PLIIx DSP AUTO DIGITAL 2 3 4 1. Input, frequency, volume level, operating information, etc. 2. Surround mode indicators 3. AUTO indicator 4. DIGITAL INPUT indicator 5. DIRECT indicator 6. Preset number, sleep time, speaker distance display 11 mft DIRECT 5 6 7. MEMORY indicator 8. PRESET indicator 9. SLEEP indicator 10. TUNED indicator 11. STEREO indicator 18 17 ■ VIDEO 3 INPUT JACKS ENGLISH VIDEO 3 L - AUDIO - R VIDEO VIDEO 3 VIDEO L - AUDIO - R When not using the VIDEO 3 INPUT jacks, cover these jacks with the supplied cap. L VIDEO OUT VIDEO 3 R AUDIO OUT • The VIDEO 3 jacks may be also connected to an additional video component such as a camcorder, LD player, video game player, etc. Camcorder, video game player, etc. 12 ENGLISH Universal Remote Controls This universal remote control can operate not only this receiver but also most popular brands of audio and video components such as CD players, cassette decks, TVs, cable boxes, VCRs, DVD players, satellite receivers, etc. • To operate 7 components other than this receiver, you should enter the setup code for each component. (For details, refer to “USING FUNCTIONS OF REMOTE CONTROL” on page 16.) Digi link system remote controls This remote control can also operate Sherwood compatible components bearing the DIGI LINK (II or III) logo. • For digi link system remote control operation, first make the DIGI LINK connections between Sherwood components. • The numbered buttons on the remote control have different functions in different device modes. For details, refer to “FUNCTION TABLE of the NUMBERED BUTTONS” on the following page 14. LED POWER button 1 POWER ON STANDBY AUD CD AUX TV VCR DVD SAT CBL 2 DEVICE buttons • To operate the desired component with this remote control, first select the corresponding DEVICE button. DEVICE SELECT CHANNEL SELECTOR button 3 CHANNEL LEVEL UP/DOWN( / ) buttons 4 TEST TONE button 7 CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE OSD MENU SLEEP DIMMER DISPLAY RETURN SLEEP button 10 TUNE TUNE PRESET P.SCAN PRESET AUTO DSP STEREO SPK SET ADJUST PARAMATER AUTO button SPEAKER SETUP button NUMERIC(0~9, +10) / 18 INPUT SELECTOR buttons • To select the desired input source of TUNER~VIDEO 3 MUTE button 8 OSD button 9 CURSOR CONTROL( ENTER buttons , , , 11 DIMMER button 13 14 PRESET SCAN button STEREO button ADJUST UP/DOWN( / ) buttons PARAMETER button TUNER CD AUX TAPE 1 2 3 4 VIDEO 1 5 6 VIDEO 2 VIDEO 3 7 8 EXT. IN 9 MACRO buttons • To operate a macro function, press the corresponding MACRO button. 6 15 PRESET UP/DOWN(+/-) buttons 17 16 DSP MODE UP/DOWN( / ) buttons VOLUME UP/DOWN( / ) buttons SETUP ENTER TUNING UP/DOWN(+/-) buttons 12 5 0 +10 MACRO M1 M2 13 M3 EXTERNAL IN button ), FUNCTION TABLE of the NUMBERED BUTTONS Button symbol CD AUX TV VCR (for CD player) (for tape deck) (for TV) (for VCR) DVD CBL SAT (for DVD player) (for satellite receiver) (for cable box) 1 POWER ON POWER ON POWER ON POWER ON POWER ON POWER ON POWER ON POWER ON 2 STANDBY STANDBY (POWER OFF) STANDBY (POWER OFF) STANDBY (POWER OFF) STANDBY (POWER OFF) STANDBY (POWER OFF) STANDBY (POWER OFF) STANDBY (POWER OFF) ENGLISH Device to be controlled CH.SEL 3 T/V 4 CH/LEVEL 5 VOLUME INPUT SELECTOR INPUT SELECTOR INPUT SELECTOR INPUT SELECTOR CHANNEL LEVEL CHANNEL LEVEL UP/DOWN( / ) UP/DOWN( / ) CHANNEL LEVEL CHANNEL LEVEL UP/DOWN( / ) UP/DOWN( / ) VOLUME UP/DOWN( / VOLUME UP/DOWN( / ) VOLUME UP/DOWN( / ) VOLUME ) UP/DOWN( / MUTE MUTE 6 MUTE MUTE MUTE NUMERIC NUMERIC T.TONE 7 MENU MENU OSD SETUP 8 SETUP CURSOR CONTROL 9 ENTER ENTER SLEEP 10 DISPLAY DISPLAY DIMMER 11 RETURN RETURN TUNE TUNE 12 REWIND( ) / FAST FORWARD( REWIND( ) / FAST FORWARD( 13 RECORD RECORD STOP STOP ) REVERSE SEARCH( ) / ) FORWARD SEARCH( ) P.SCAN STOP 14 STOP 15 REVERSE SKIP( ) / FORWARD SKIP( ) 16 PAUSE REVERSE PLAY PAUSE PAUSE 17 PLAY FORWARD PLAY PLAY PLAY NUMERIC NUMERIC PRESET 18 0 PRESET 9 +10 NUMERIC REVERSE SKIP( ) / FORWARD SKIP( ) NUMERIC Notes: • Some functions for each component may not be available or may work differently. • Depending on other kinds of components that are available for each DEVICE button, some functions may not be available or may work differently, too. • For details about functions, refer to the operating instructions of each component. 14 ) ENGLISH OPERATING COMPONENTS WITH REMOTE CONTROL 1 2 REMOTE CONTROL OPERATION RANGE Enter the setup code for each component other than this receiver you wish to control. For details, refer to “Entering a setup code” on page 16. • Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor. Turn on the component you want to operate. AUDIO/VIDEO RECEIVER RD-8601 MASTER VOLUME POWER REMOTE SENSOR ON/ OFF INPUT SELECTOR STANDBY AUDIO VIDEO SURROUND MODE EXTERNAL IN AUTO DSP MODE STEREO PARAMETER DIGITAL INPUTS ON/STANDBY VIDEO 3 PHONES SPEAKER CHANNEL SELECTOR ADJUST TONE MODE SPEAKER SETUP DYNAMIC RANGE CINEMA EQ MEMO/ENTER TUNING/PRESET T/P MODE FM MODE BAND ON/OFF VIDEO 3 4 Press the DEVICE button on the remote control corresponding to the component you wish to operate. L - AUDIO - R 7m 30 Aim the remote control at the REMOTE SENSOR of the component you wish to control and press the button corresponding to the operation you want. 30 POWER ON AUD VCR STANDBY ST ANDBY CD AUX TV DVD SAT CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU • When operating a Sherwood CD player or tape deck using digi link system remote control, aim the remote control at the REMOTE SENSOR of this receiver. However, to operate a Sherwood DVD player, aim at the REMOTE SENSOR of the corresponding component. SETUP ENTER DIMMER SLEEP DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN 1 STEREO ADJUST SPK SET TUNER PRESET DSP AUTO CD 2 VIDEO 1 PARAMA ARAMATER AUX 3 TAPE 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A LOADING BATTERIES • When the remote control does not operate, the old batteries should be replaced. In this case, load new batteries within several minutes after removing old batteries. • If the batteries are removed or have been exhausted for a longer period of time, memorized contents will be cleared. Should this happen, you should memorize them again. 1 Remove the cover. 2 Load two batteries(“AAA” size) matching the polarity. + + • Remove the batteries when they are not used for a long time. • Do not use the rechargeable batteries(Ni-Cd type). • Be sure to use alkaline batteries. 15 • This remote control can control up to 8 different components. • Before operating audio and video components other than this receiver with using this remote control, the setup code for each component should be entered. • For system remote control operation, “000” was stored previously in the memory of the device button “CD” for Sherwood CD player, “DVD” for Sherwood DVD player and “AUX” for Sherwood tape deck respectively as its factory setup code. So, you don’t need to enter its code for each Sherwood component except in such a case that its code does not work. Entering a setup code CD AUX TV DVD SAT CBL POWER ON STANDBY CD 1 VCR Turn on the component you want to control. ENGLISH USING FUNCTIONS OF REMOTE CONTROL AUX TV Find the setup codes according to the type and the brand name of your component, referring to “Setup Code Table” on page 52. DVD VCR SAT CBL CH.SEL 2 T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET ENTER P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 3 Press and hold down both the “ENTER” button and the desired one of the DEVICE buttons for more than 1 second. M2 M3 Enter a 3 digit code, aiming the remote control at the remote sensor on the component. Example) When entering “001”. REMOTE CONTROL RNC-50A 4 POWER ON AUD CD AUX TV STANDBY ST ANDBY CD VCR AUD AUX DVD TV SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL POWER ON AUD VCR DVD SAT CBL STANDBY ANDBY CD AUX TV DVD SAT SA CBL VOLUME MUTE T.TONE .TONE OSD MENU VCR DIMMER DISPLAY DISPLA CH.SEL RETURN TUNE T/V CH/LEVEL SETUP ENTER SLEEP DEVICE SELECT VOLUME MUTE T.TONE .TONE TUNE PRESET P.SCAN PRESET TUNER OSD MENU SETUP AUTO DSP SPK SET ADJUST STEREO ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE 0 0 1 TUNER PRESET P.SCAN CD 3 VIDEO 1 PRESET PARAMA ARAMATER TER AUX 2 1 TUNE TAPE 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN ENTER AUTO DSP STEREO SPK SET ADJUST PARAMA ARAMATER TER MACRO M1 TUNER CD AUX 2 1 3 VIDEO 1 TAPE M2 M3 REMOTE CONTROL RNC-50A RNC 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 • If entering is performed successfully, the LED will flicker twice. • To be sure that the setup code is correct, press the POWER(or STANDBY) button. If your component is tuned off, the setup code is correct. • When your component is not turned off, repeat the above steps ② to ④, trying each code for your component until you find one that works. REMOTE CONTROL RNC-50A RNC • The LED will flicker once. Note: • The “AUD” button is unavailable for the audio components other than this receiver. POWER ON VCR POWER ON AUX TV SAT CBL AUX TV SAT CBL POWER ON T/V MUTE T.TONE OSD MENU SETUP AUX TV SAT CBL CH.SEL T/V CH/LEVEL STANDBY CD DVD VCR CH.SEL MUTE T.TONE DVD VCR CH.SEL CH/LEVEL STANDBY CD STANDBY CD DVD T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP OSD ENTER MENU ENTER SETUP SLEEP DIMMER SLEEP DIMMER DISPLAY RETURN DISPLAY RETURN ENTER SLEEP 0 0 1 TUNE DIMMER DISPLAY PRESET TUNE P.SCAN PRESET DSP STEREO ADJUST SPK SET 1 2 5 9 PARAMATER 3 4 6 7 8 0 +10 TUNE Notes: • If the LED did not flicker twice, then repeat the above steps ③ to ④ and try entering the same code again. • Manufacturers may use different setup codes for the same product category. For that reason, it is important that you check to see if the code you have entered operates as many controls as possible. If only a few functions operate, check to see if another code will work with more buttons. • When operating a Sherwood CD player or tape deck using the system remote control, aim the remote control at the REMOTE SENSOR on this receiver. However, in case of Sherwood DVD player and MD recorder, aim it at the REMOTE SENSOR on the corresponding component. RETURN TUNE PRESET AUTO P.SCAN PRESET TUNE STEREO AUTO DSP PARAMATER SPK SET ADJUST M2 M3 3 4 1 2 3 4 6 7 8 5 6 7 8 0 +10 0 +10 M2 M3 REMOTE CONTROL RNC-50A 5 Repeat the above steps ① to ④ for each of your components. POWER ON STANDBY CD DVD VCR AUX TV SAT CBL POWER ON STANDBY CD DVD VCR AUX TV SAT CBL POWER ON STANDBY CD DVD VCR CH.SEL CH/LEVEL AUX TV SAT CBL CH.SEL T/V T/V CH/LEVEL MUTE MUTE CH.SEL T.TONE OSD T.TONE T/V OSD CH/LEVEL MENU SETUP MENU MUTE SETUP T.TONE ENTER OSD ENTER MENU SLEEP SLEEP DIMMER SETUP DIMMER ENTER DISPLAY RETURN TUNE DISPLAY TUNE RETURN TUNE TUNE DIMMER SLEEP PRESET P.SCAN PRESET PRESET P.SCAN PRESET DISPLAY RETURN TUNE AUTO STEREO AUTO PARAMATER SPK SET 3 4 1 2 6 7 8 5 0 +10 9 DSP ADJUST SPK SET 1 2 5 9 MACRO M1 M2 DSP STEREO ADJUST 4 6 7 8 0 +10 M1 M2 TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M3 AUTO PARAMATER 3 M3 MACRO REMOTE CONTROL RNC-50A REMOTE CONTROL RNC-50A 16 STEREO PARAMATER 2 5 M1 MACRO PRESET 1 9 MACRO M1 P.SCAN DSP ADJUST 9 REMOTE CONTROL RNC-50A TUNE PRESET AUTO SPK SET M1 M2 M3 REMOTE CONTROL RNC-50A MACRO M1 M2 M3 REMOTE CONTROL RNC-50A T.TONE OSD MENU DVD VCR SAT CBL SETUP ENTER CH.SEL SLEEP DIMMER DISPLAY RETURN T/V CH/LEVEL TUNE MUTE TUNE T.TONE PRESET P.SCAN OSD PRESET MENU SETUP ENTER ENTER AUTO DSP STEREO SPK SET ADJUST PARAMATER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET 1 2 3 4 5 6 7 8 9 0 +10 0 MACRO M1 M2 M3 1 0 REMOTE CONTROL RNC-50A P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 POWER ON STANDBY CD 9 DVD VCR AUX TV SAT CBL MACRO M1 M2 M3 CH.SEL T/V REMOTE CONTROL RNC-50A CH/LEVEL MUTE T.TONE Using a punch-through function OSD MENU SETUP Removing a punch-through function ENTER DIMMER SLEEP • When removing the AUDIO volume punchthrough, press and 1 hold down both “AUD” button 0 0 and “VOLUME ▼” button for more than 1 second. DISPLAY RETURN TUNE TUNE ENGLISH PRESET This remote control may be programmed to operate either the AUDIO volume punch-through or the TV volume and/or TV channel punch-through in conjunction with any of the eight components controlled by this remote control. For example, since this receiver will likely be used as the sound system while watching TV, you may want to 1 0 0 adjust this receiver’s volume although this remote control is set to control the TV. • When programming this remote control for the AUDIO volume punch-through, press and hold down both “AUD” button and “VOLUME ▲” button for more than 1 second. POWER ON STANDBY CD DVD VCR AUX TV SAT CBL P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU AUD SETUP ENTER SLEEP DIMMER DISPLAY RETURN POWER ON TUNE STANDBY POWER ON CD AUX TV AUD DVD SAT CBL VCR STANDBY ST ANDBY CD AUX TV SAT SA CBL TUNE PRESET P.SCAN AUTO VCR PRESET DSP CH.SEL T/V T/V CH/LEVEL ADJUST SPK SET CH/LEVEL MUTE T.TONE 2 3 4 5 6 7 8 9 0 +10 OSD T.TONE .TONE SETUP MENU SLEEP DIMMER SLEEP DIMMER DISPLAY RETURN DISPLAY DISPLA RETURN MENU OSD SETUP ENTER ENTER TUNE MACRO M2 VOLUME MUTE PARAMATER 1 M1 DVD DEVICE SELECT CH.SEL STEREO TUNE TUNE TUNE M3 PRESET P.SCAN PRESET PRESET P.SCAN PRESET VOLUME REMOTE CONTROL RNC-50A AUTO DSP STEREO AUTO DSP SPK SET ADJUST PARAMATER SPK SET ADJUST TUNER 1 2 3 4 5 6 7 8 CD 0 9 VCR M2 4 STANDBY 7 M1 SAT M2 T.TONE MENU POWER ON SLEEP DIMMER DISPLAY RETURN TUNE P.SCAN OSD AUX TV STEREO AUTO DSP PARAMATER SPK SET ADJUST RETURN SAT CBL P.SCAN 3 4 1 2 3 4 6 7 8 5 6 7 8 0 +10 0 +10 STEREO PARAMA ARAMATER TER AUX 2 3 AUX TV SAT CBL 7 0 9 M1 M2 4 CH.SEL T/V 8 CH/LEVEL MUTE T.TONE OSD MENU SETUP PRESET DSP STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 +10 M2 P.SCAN ADJUST MACRO M3 M1 ENTER M3 DIMMER SLEEP REMOTE CONTROL RNC RNC-50A REMOTE CONTROL RNC-50A DISPLAY RETURN TUNE TUNE PRESET AUTO P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET • If programming is performed successfully, the LED will flicker twice. • When you want either TV volume or TV channel punch-through, press and hold down both “TV” button and either “VOLUME ▲” or “CH/LEVEL ▲” button for more than 1 second. POWER ON M2 AUD PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 POWER ON AUD M2 STANDBY ANDBY CD AUX DVD VCR MACRO M1 TV SAT SA CBL DEVICE SELECT M3 CH.SEL T/V REMOTE CONTROL RNC-50A CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET AUTO P.SCAN AUTO DSP SPK SET ADJUST TUNER CD STEREO PARAMA ARAMATER TER 3 VIDEO 1 5 PRESET AUX 2 1 TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 STANDBY CD AUX TV DVD SAT CBL MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A CH.SEL Note : • If you use one of AUDIO and TV volume punchAUTO you cannot use the other. through functions, ENTER T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP • If removing all punch-through functions is performed successfully, the LED will flicker twice. ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN POWER ON STANDBY CD AUX TV DVD SAT CBL POWER ON PRESET AUTO DSP STEREO SPK SET ADJUST PARAMATER VCR VCR AUX TV SAT CBL CH.SEL 2 1 3 4 6 7 8 0 +10 CH.SEL T/V CH/LEVEL T/V CH/LEVEL MUTE T.TONE 5 MENU 9 STANDBY CD DVD OSD T.TONE SETUP MENU DIMMER SLEEP MUTE OSD SETUP ENTER ENTER SLEEP DIMMER MACRO M1 M2 DISPLAY M3 RETURN TUNE DISPLAY TUNE PRESET P.SCAN RETURN TUNE PRESET TUNE PRESET P.SCAN PRESET REMOTE CONTROL RNC-50A 1 AUTO DSP SPK SET ADJUST STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 M1 AUTO DSP SPK SET ADJUST STEREO PARAMATER 1 2 3 5 6 7 0 +10 4 POWER ON STANDBY 8 CD 9 9 DVD VCR ENTER MACRO M1 M2 M3 REMOTE CONTROL RNC-50A AUX TV SAT CBL POWER ON M2 T/V REMOTE CONTROL RNC-50A CH/LEVEL CH/LEVEL MUTE MUTE OSD T.TONE SETUP MENU SLEEP DIMMER SLEEP DIMMER DISPLAY RETURN DISPLAY RETURN OSD SETUP ENTER TUNE TUNE PRESET 1 STANDBY POWER ON TV DVD VCR SAT AUX DVD VCR SAT STEREO AUTO DSP PARAMATER SPK SET ADJUST 1 2 3 4 5 6 7 8 0 +10 9 M3 M1 9 T/V CH/LEVEL MUTE T.TONE OSD T.TONE OSD MENU SETUP MENU SETUP ENTER ENTER SLEEP SLEEP DIMMER DISPLAY RETURN TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST TUNE PRESET TUNE AUTO DSP PARAMATER SPK SET ADJUST 2 3 4 5 6 7 8 9 0 +10 M3 M1 M1 PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 MACRO M2 RETURN P.SCAN STEREO 1 M1 DIMMER DISPLAY TUNE PRESET MACRO REMOTE CONTROL RNC-50A M2 M3 REMOTE CONTROL RNC-50A 17 M1 PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 MACRO M2 MACRO M2 M3 CBL CH.SEL T/V MUTE P.SCAN DSP ADJUST REMOTE CONTROL RNC-50A CH.SEL PRESET AUTO TV ENTER 1 PRESET TUNE STANDBY CD CBL P.SCAN TUNE SPK SET M1 CH/LEVEL CBL CH.SEL T/V ENTER AUX TV SAT CH.SEL T.TONE CD AUX M3 MENU POWER ON STANDBY CD DVD VCR MACRO M1 M3 REMOTE CONTROL RNC-50A Press and hold down both “AUD” button and “AUTO” button for more than 1 second. TAPE MACRO VCR M3 Removing all punch-through functions SPK SET EXT. IN M1 M2 MACRO TUNE STANDBY CD DVD VIDEO 2 VIDEO 3 6 RETURN AUTO VCR CD DIMMER PRESET POWER ON DSP ADJUST VIDEO 1 9 MACRO SETUP SLEEP DISPLAY TUNE PRESET AUTO SPK SET STEREO PARAMATER 2 5 OSD MENU TUNE PRESET 1 ENTER DIMMER 5 P.SCAN DSP ADJUST MUTE T.TONE SETUP ENTER 1 PRESET AUTO REMOTE CONTROL RNC-50A SLEEP TUNER PRESET TUNE T/V T.TONE .TONE VOLUME RETURN CH.SEL CH/LEVEL VOLUME MENU PRESET DVD VCR T/V DISPLAY DISPLA OSD SETUP DIMMER DISPLAY TUNE SPK SET M1 CBL CH.SEL TUNE MUTE SLEEP STANDBY CD DEVICE SELECT MUTE CBL ENTER • If removing is performed successfully, the LED will flicker twice. • When you want to remove either TV volume or TV channel punch-through, press and hold down both “TV” button and either “VOLUME ▼” or “CH/LEVEL ▼” button for more than 1 second. TV SAT SA CH/LEVEL OSD SETUP ENTER STANDBY ANDBY DVD VCR TV SAT T/V T.TONE 9 CH/LEVEL AUX CH.SEL T/V MENU AUD AUX DVD CH.SEL REMOTE CONTROL RNC-50A RNC CH/LEVEL MUTE PRESET CD VCR CBL M3 TUNE POWER ON STANDBY CD +10 DVD MACRO M3 REMOTE CONTROL RNC-50A AUD POWER ON 8 EXT. TV IN AUX 0 9 +10 MACRO TAPE VIDEO 2 VIDEO 3 6 CD M1 STEREO 3 VIDEO 1 5 PARAMA ARAMATER TER AUX 2 1 POWER ON REMOTE CONTROL RNC-50A POWER ON STANDBY CD CBL DVD VCR AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU POWER ON RETURN AUX TV SAT CBL DVD VCR DIMMER DISPLAY TUNE STANDBY CD SETUP ENTER SLEEP OSD CH.SEL TUNE T/V PRESET P.SCAN CH/LEVEL PRESET MUTE T.TONE AUTO DSP STEREO SPK SET ADJUST PARAMATER OSD MENU SETUP ENTER SLEEP 2 1 3 4 6 7 8 0 +10 DIMMER DISPLAY TUNE PRESET 9 MACRO M2 SETUP RETURN TUNE 5 M1 P.SCAN AUTO PRESET DSP STEREO M3 ADJUST SPK SET REMOTE CONTROL RNC-50A PARAMATER Programming a macro function 2 1 5 3 6 4 7 POWER ON 9 0 2 8 STANDBY +10 CD MACRO DVD VCR AUX TV SAT CBL • The macro function enables you to program a series of button operations(up to 10) on this remote control into a single button. • You can store upAUTO to three separate macro command sequences into “M1”, “M2” and “M3” buttons. M1 M2 M3 CH.SEL REMOTE CONTROL RNC-50A T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP Press the operation buttons you want to program in order. ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO STANDBY CD VCR DVD AUX TV SAT CBL STEREO ADJUST SPK SET POWER ON PRESET DSP 2 1 5 6 4 7 0 9 PARAMATER 3 8 +10 POWER ON STANDBY Press and hold down both “ENTER” button and one of three NUMERIC buttons (“1”~“3”) corresponding to “M1”~“M3” buttons for more than 1 second. Example) When programming a series of button operations into “M1” button. MACRO CD CH.SEL T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE P.SCAN PRESET 1 TV M2 M3 DVD VCR MUTE PRESET AUX M1 T/V CH/LEVEL SAT CBL REMOTE CONTROL RNC-50A CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE AUTO DSP STEREO TUNE PRESET 1 ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 MACRO M1 M2 M3 P.SCAN DSP ADJUST STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 REMOTE CONTROL RNC-50A PRESET AUTO SPK SET MACRO M1 M2 M3 REMOTE CONTROL RNC-50A POWER ON AUD VCR ENTER STANDBY ANDBY POWER ON CD AUX TV DVD SAT SA CBL CD DVD VCR DEVICE SELECT CH.SEL T.TONE .TONE MENU OSD T.TONE SETUP MENU OSD SETUP ENTER AUX TV SAT CBL SLEEP DIMMER DISPLAY DISPLA RETURN TUNE P.SCAN DIMMER DISPLAY TUNE PRESET CBL MUTE STANDBY ENTER CD SLEEP DVD TV SAT T/V CH/LEVEL VOLUME MUTE POWER ON VCR STANDBY AUX CH.SEL T/V CH/LEVEL Note: You should press the corresponding DEVICE buttons before pressing each operation button. Example) When playing a DVD on the DVD player connected to VIDEO 2 jacks of this receiver. 1. Press “AUDIO” button to control this receiver. 2. Press “POWER” button to turn this receiver on. 3. Press “AUDIO” button to control this receiver. 4. Press “VIDEO 2(7)” button to select the desired input source. 5. Press “DVD” button to control the DVD player. 6. Press “POWER” button to turn the DVD player on. 7. Press “DVD” button to control the DVD player. 8. Press “▶” button to start playback. RETURN TUNE PRESET TUNE PRESET P.SCAN PRESET CH.SEL AUD T/V CH/LEVEL MUTE DSP AUTO T.TONE POWER ON TUNER STANDBY CD AUX MENU DVD SAT 1 3 6 7 VCR DISPLAY 0 PRESET AUX TV SAT CBL 1 8 DVD M1 EXT. IN RETURN 9 TUNE CD 4 VIDEO 2 VIDEO 3 DIMMER 5 9 TUNE +10 P.SCAN 3 4 6 7 8 0 +10 POWER ON VIDEO 2 7 CH.SEL T/V T/V MACRO M1 MUTE T.TONE M2 M3 CH/LEVEL DSP AUTO OSD MACRO M1 MUTE STEREO T.TONE ADJUST SPK SET SETUP DVD SETUP ENTER DIMMER RETURN TUNE TUNE P.SCAN PRESET 1 2 3 5 6 7 DIMMER 8 POWER ON RETURN TUNE TUNE • If the macro mode is entered, the LED will flicker once. 0 DVD 4 SLEEP DISPLAY 9 M3 REMOTE CONTROL RNC-50A PARAMATER MENU ENTER SLEEP M2 OSD REMOTE CONTROL RNC RNC-50A MENU DISPLAY PRESET 2 PRESET CH.SEL CH/LEVEL AUD STEREO PARAMATER STANDBY TAPE AUX 2 VIDEO 1 5 CBL DSP ADJUST POWER ON CD ENTER 1 SLEEP VCR AUTO SPK SET SETUP TUNER TV STEREO PARAMA ARAMATER TER OSD ADJUST SPK SET +10 PRESET P.SCAN PRESET MACRO M1 M2 M3 AUTO DSP STEREO SPK SET ADJUST PARAMATER SPK SET AUTO DSP STEREO REMOTE CONTROL RNC-50A ADJUST PARAMATER 1 2 3 4 1 2 3 4 5 6 7 8 5 6 7 8 0 +10 0 +10 9 9 MACRO M1 M2 MACRO M3 Press “ENTER” button. M1 REMOTE CONTROL RNC-50A M2 M3 REMOTE CONTROL RNC-50A 3 To remove a macro program POWER ON AUD VCR • When removing a macro program, perform the above steps ① and ③, but ignore the step ②. STANDBY ANDBY CD AUX DVD SAT SA TV CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU To change a macro program SETUP ENTER DIMMER SLEEP DISPLAY DISPLA ENTER • When a new macro program is stored into a MACRO button with performing the above steps ① to ③, the previous macro program is cleared from the memory of the MACRO button. RETURN TUNE TUNE PRESET P.SCAN PRESET DSP AUTO STEREO ADJUST SPK SET TUNER CD PARAMA ARAMATER TER TAPE AUX 2 1 3 VIDEO 1 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN POWER ON VCR STANDBY CD AUX TV DVD SAT CBL MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE AUTO TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET • If the programming is performed successfully, the LED will flicker twice. PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 POWER ON MACRO M1 M2 VCR M3 REMOTE CONTROL RNC-50A AUX TV SAT CBL Operating a macro function CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP Notes: • The codes programmed into a MACRO button will be transmitted at an interval of 0.5 seconds. However, some components may not be able to complete one operation in 0.5 seconds and may miss the next code. In this case, the macro function cannot control the corresponding components correctly. • Be sure to use the remote control within the remote control operation range of the components. • Depending on the operation status of the components, etc., the macro function cannot control the corresponding components correctly. • Aim the remote control at the REMOTE SENSORs of the components to be controlled and press the MACRO button you want. Example) When pressing “M1” button. ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET DSP AUTO STEREO ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A POWER ON STANDBY CD DVD VCR POWER ON AUX TV AUD SAT CBL VCR TER 1 STANDBY CD DVD STANDBY ANDBY CD DVD AUX TV SAT SA CBL DEVICE SELECT CH.SEL CH.SEL T/V T/V CH/LEVEL CH/LEVEL MUTE T.TONE VOLUME MUTE OSD T.TONE .TONE SETUP MENU SLEEP DIMMER SLEEP DIMMER DISPLAY RETURN DISPLAY DISPLA RETURN MENU OSD SETUP ENTER ENTER TUNE TUNE PRESET P.SCAN TUNE PRESET TUNE PRESET P.SCAN AUTO DSP STEREO AUTO DSP SPK SET ADJUST PARAMATER SPK SET ADJUST TUNER 1 2 3 4 5 6 7 8 0 +10 9 1 M1 M2 2 STEREO PARAMA ARAMATER TER AUX 3 TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 CD VIDEO 1 5 PRESET MACRO M3 REMOTE CONTROL RNC-50A M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A 18 ENGLISH TER ENGLISH Speaker Setup • After you have installed this receiver and connected all the components, you should adjust the speaker settings for the optimum sound acoustics according to your environment and speaker layout. • Even when you change speakers, speaker positions, or the layout of your listening environment, you should adjust the speaker settings, too. About the speaker size The composition of the signals output from the different channels and the frequency response are adjusted automatically according to the combination of speakers actually being used. • Select “Large” or “Small” not according to the actual size of the speaker but according to the speaker’s capacity for playing low frequency (bass sound below frequency set for the Crossover Frequency mode and below) signals. • Depending or relationship between speakers, settings possible for each speaker are as follows: Front L/R Center Surr. L/R Large Large Small Large : Select this when connecting speakers that can fully reproduce sounds below crossover frequency(*) of your speaker. Small : Select this when connecting speakers that cannot fully reproduce sounds below crossover frequency. When this setting is selected, sounds below crossover frequency are sent to the subwoofer or speakers which are set to “Large”(when not using a subwoofer). None : Select this when no speakers are connected. When this is selected, sounds are sent to the speakers which are not set to None. Yes / None : Select the desired depending on whether a subwoofer is connected or not. None Large Large Small Small None Large None • (*) : Crossover frequency is the frequency (Hz) below which the bass sound of each main speakers is to output from the subwoofer or from speakers which are set to “Large” (when not using a subwoofer). • Refer to the operating instructions of the speakers to be connected. If the frequency range of your speaker is 100 Hz ~ 20 kHz, the crossover frequency have to be set to 100 Hz(or slightly higher). • If you do not know, try comparing the sound at both settings (setting the volume to a level low enough so as not to damage the speakers) to determine the proper setting. Small None Small Small Small None None Small None Surr. Back Large Small None Small None X Large Small None Small None X Large Small None Small None X Small None X Small Subwoofer Yes or None Yes None X About the speaker distance When enjoying multi-channel surround playback with Dolby Digital and DTS sources, etc., it is ideal that the center and surround speakers, etc. should be the same distance from the main listening position as the front speakers. By entering the distance between the listening position and each speaker, the delay times of center and surround speakers are automatically adjusted to create an ideal listening environment virtually as if the center and surround speakers were at their ideal locations respectively as below: Ideal location of a center speaker FL SW FR C Dc Df All speakers should be located within a circle with a radius of Df Ds Db SL SB SR Ideal location of a surround speaker Ideal location of a surround back speaker 19 Df : Distance between front speakers and listening position Dc : Distance between center speaker and listening position Ds : Distance between surround speakers and listening position Db : Distance between surround back speaker and listening position SETTING THE SPEAKER SETUP MANUALLY ENGLISH Note: When the SPEAKER button is set to off or the EXTERNAL IN is selected as an input source, the speaker setup procedure cannot be performed. Before setting the speaker setup • Press the POWER switch to enter the standby mode and then turn the power on. POWER POWER ON POWER ON AUD STANDBY CD VCR AUX DVD TV SAT SA CBL POWER ON STANDBY DEVICE SELECT CD AUX TV SAT CBL CH.SEL STANDBY VCR T/V CH/LEVEL DVD VOLUME MUTE T.TONE .TONE OSD CH.SEL T/V MENU SETUP CH/LEVEL MUTE ENTER T.TONE ON/ SLEEP OFF ON/STANDBY OSD DIMMER MENU DISPLAY DISPLA SETUP RETURN TUNE TUNE ENTER PRESET or P.SCAN PRESET SLEEP DIMMER DISPLAY RETURN TUNE AUTO DSP STEREO ADJUST SPK SET TUNER CD 3 VIDEO 1 PRESET PRESET TAPE AUTO 4 DSP STEREO VIDEO 2 VIDEO 3 5 6 7 9 0 +10 SPK SET MACRO M2 ADJUST SPK SET 8 EXT. IN M1 P.SCAN PARAMA ARAMATER TER AUX 2 1 TUNE PARAMATER 1 2 3 4 5 6 7 8 0 +10 M3 9 REMOTE CONTROL RNC RNC-50A 50A MACRO M1 M2 M3 REMOTE CONTROL RNC-50A 1 When selecting each setting mode, POWER ON AUD SPEAKER SETUP 2 POWER ON STANDBY CD VCR When adjusting the selected mode to the desired setting, DVD AUX TV SAT SA CBL POWER ON ADJUST POWER ON VCR DEVICE SELECT STANDBY CD AUX TV DVD SAT CBL STANDBY AUD STANDBY ANDBY CD VCR AUX DVD CH.SEL T/V T/V CH/LEVEL VOLUME MUTE TV SAT SA CBL DEVICE SELECT CH.SEL CH/LEVEL CH.SEL VOLUME MUTE T/V T.TONE .TONE CH/LEVEL OSD MENU or SETUP RETURN P.SCAN SETUP PRESET SLEEP DIMMER DISPLAY RETURN TUNE DSP AUX TAPE 2 3 4 VIDEO 1 5 SLEEP DIMMER RETURN P.SCAN PRESET 7 P.SCAN DSP STEREO ADJUST PARAMATER DSP 1 2 3 4 5 9 6 7 8 0 +10 STEREO ADJUST SPK SET ADJUST PARAMA ARAMATER TER TUNER CD AUX 1 2 3 VIDEO 1 8 PRESET PRESET AUTO SPK SET VIDEO 2 VIDEO 3 6 TUNE AUTO PARAMA ARAMATER TER CD 1 SETUP ENTER STEREO ADJUST TUNER OSD MENU DISPLAY DISPLA TUNE TUNE PRESET AUTO or ENTER TUNE SPK SET SPK SET T.TONE .TONE OSD MENU DIMMER PRESET MUTE T.TONE ENTER SLEEP DISPLAY DISPLA TUNE 5 9 0 7 0 +10 M2 4 8 EXT. IN +10 9 MACRO MACRO M1 TAPE VIDEO 2 VIDEO 3 6 EXT. IN M1 M3 M2 M3 MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A REMOTE CONTROL RNC RNC-50A 50A REMOTE CONTROL RNC-50A • Each time the SPEAKER SETUP button is pressed, the speaker setting mode changes in succession and is displayed for several seconds as follows. • When the speaker setting mode disappears, press the SPEAKER SETUP button repeatedly to select the desired mode. POWER ON STANDBY CD • When selecting the subwoofer, VCR • Each time the ADJUST UP(▲/ ) or DOWN(▼/ ) button is pressed, one of the settings is selected and displayed for several seconds as follows. DVD AUX TV SAT CBL Y(es) N(one) • When the subwoofer is set to “N”, the front speaker is automatically set to “L”. CH.SEL T/V CH/LEVEL MUTE T.TONE “SUB-W Y” OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET ADJUST P.SCAN AUTO DSP SPK SET ADJUST 1 2 PRESET STEREO PARAMATER 3 4 • When selecting the front speaker size, 5 9 6 7 0 +10 • You can select one of 2 different speaker settings. L S 8 MACRO M1 “FRONT L” M2 M3 REMOTE CONTROL RNC-50A (L: Large, S: Small) • When selecting the center speaker size, • You can select one of 3 different speaker settings. L S N “CENTER L” (L: Large, S: Small, N: None) • When selecting the surround speaker size, • You can select one of 3 different speaker settings. L S N “SURR L ” • You can select one of 3 different speaker settings. L S N • When selecting the surround back speaker size, “SURR-B L” 20 Continued ENGLISH • When selecting the distance of front left speaker, • You can adjust the distance within the range of 1 ~ 30 feet in 1 foot intervals. 1 (ft) ~ 30 (ft) “FRONT L 10 (ft)” • When selecting the distance of front right speaker, • You can adjust the distance within the range of 1 ~ 30 feet in 1 foot intervals. 1 (ft) ~ 30 (ft) “FRONT R 10 (ft)” • You can adjust the distance within the range of 1 ~ 30 feet in 1 foot intervals. 1 (ft) ~ 30 (ft) • When selecting the distance of center speaker, “CENTER 10 (ft)” • You can adjust the distance within the range of 1 ~ 30 feet in 1 foot intervals. 1 (ft) ~ 30 (ft) • When selecting the distance of surround left speaker, “SURR L 05 (ft)” • When selecting the distance of surround right speaker, “SURR R 05 (ft)” • You can adjust the distance within the range of 1 ~ 30 feet in 1 foot intervals. 1 (ft) ~ 30 (ft) • When selecting the distance of surround back speaker, “SURR-B 05 (ft)” • You can adjust the distance within the range of 1 ~ 30 feet in 1 foot intervals. 1 (ft) ~ 30 (ft) • When selecting the crossover frequency, “FC 80 Hz” • You can adjust the crossover frequency within the range of 40 ~ 130 Hz in 10 Hz intervals. 40 Hz ~ 130 Hz Notes: • You cannot adjust the distances of subwoofer and the speakers set to “None”. • When speakers are set to “Small”, you should set the crossover frequency according to their frequency characteristics. 3 Memorize the adjusted speaker settings. POWER ON AUD STANDBY CD VCR AUX DVD TV SAT SA CBL • The adjusted settings are memorized in the memory. DEVICE SELECT MEMO/ENTER CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER or DIMMER SLEEP DISPLAY DISPLA TUNE P.SCAN STEREO ADJUST SPK SET 1 PRESET DSP AUTO TUNER ENTER RETURN TUNE PRESET CD 2 VIDEO 1 PARAMATER TER AUX 3 TAPE 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A 21 • Auto Speaker Setup lets you avoid troublesome listening-based speaker setup and achieve good surround sound. You should connect the microphone to the SETUP MIC jack so that this receiver can analyze the information from a series of test tones emitted from speakers and can adjust the size, distance and sound level of each speaker automatically. • If you want to personalize your speaker setup and channel level setup by making the settings manually, perform the “SETTING THE SPEAKER SETUP MANUALLY” procedure on page 20, “Adjusting each channel level with test tone” procedure on page 32 and “Adjusting the current channel level” procedure on page 33. Note: • Because the microphone for Auto Speaker Setup is designed for use with this receiver, to use the auto speaker setup function, do not use a microphone other than the one supplied with this receiver. Before setting the speaker setup • Press the POWER switch to enter the standby mode and then turn the power on. POWER POWER ON POWER ON AUD STANDBY CD VCR AUX DVD TV SAT SA CBL DEVICE SELECT CH.SEL STANDBY T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER ON/ OFF ON/STANDBY SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET or P.SCAN AUTO DSP SPK SET ADJUST TUNER CD STEREO 3 VIDEO 1 5 PARAMA ARAMATER AUX 2 1 PRESET TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A 1 Connect the optional microphone to the SETUP MIC jack on the rear panel.(For details, refer to “CONNECTING MICROPHONE” on page 10.) 2 Place the microphone on a flat level surface at your normal listening position. • If possible, use a tripod, etc. to attach the microphone at the same height as your ears would POWER ON STANDBY be when you are seated in your listening position. • Ensure there are no obstacles between the speakers and the microphone. POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET 3 Press and hold down the SPEAKER SETUP button on the front panel for more than 2 seconds to enter the auto speaker setup mode. POWER ON STANDBY CD SPEAKER SETUP DVD VCR AUX TV SAT CBL T/V MUTE T.TONE OSD MENU DSP ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A • Then “SET ALL S” is displayed. • For your reference, the default settings for auto speaker setup are as follows: Speaker layout: ALL channels, Subwoofer: Yes, CUToff frequency: 80 Hz CH.SEL CH/LEVEL P.SCAN AUTO SPK SET SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN DSP AUTO STEREO ADJUST SPK SET SPK SET PRESET 2 1 5 9 PARAMATER 3 4 6 7 8 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER 22 • When performing auto speaker setup according to the default settings, skip the step ④ and perform the step ⑤. • However, you can specify these settings according to the number of speakers installed and speakers’ frequency characteristics with performing the step ④. • To cancel the auto speaker setup mode, press and hold down the SPEAKER SETUP button on the front panel for more than 2 seconds again. ENGLISH SETTING THE SPEAKER SETUP AUTOMATICALLY (AUTO SPEAKER SETUP) ENGLISH 4 Specify the setting condition. When specifying the number of speakers installed. • Each time this button is pressed, the speaker layout changes as follows: POWER ON AUD SPEAKER SETUP STANDBY CD VCR DVD AUX TV SAT SA CBL ALL : All speakers DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU or 3/2 : 2 front, center and 2 surround speakers SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN DSP AUTO TUNER CD PARAMATER TAPE AUX 2 1 3 VIDEO 1 2/2 : 2 front and 2 surround speakers STEREO ADJUST SPK SET SPK SET PRESET 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN 3/0 : 2 front and center speakers MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A 2/0 : 2 front speakers When specifying the subwoofer or the crossover frequency. • Each time the ADJUST UP(▲) or CURSOR RIGHT(▶) button is pressed, the subwoofer changes as follows: POWER ON AUD STANDBY CD VCR POWER ON AUX AUX S TV DVD SAT SA STANDBY CD CBL TV DEVICE SELECT VCR DVD SAT CBL CH.SEL T/V CH/LEVEL VOLUME MUTE (Subwoofer: Yes) No display (None) CH.SEL T.TONE .TONE T/V CH/LEVEL OSD MUTE MENU PTY SELECT T.TONE ADJUST MENU SETUP SEARCH MODE DIMMER SLEEP ENTER DISPLAY DISPLA RETURN TUNE TUNE DIMMER SLEEP PRESET P.SCAN DISPLAY AUTO PRESET RETURN TUNE TUNE PRESET or ADJUST SETUP OSD RDS ENTER P.SCAN PRESET AUTO DSP STEREO SPK SET ADJUST PARAMATER DSP TUNER 1 CD 2 STEREO AUX 3 TAPE 4 ADJUST PARAMATER VIDEO 1 VIDEO 2 VIDEO 3 SPK SET 5 1 2 9 5 6 9 0 M1 6 7 3 0 4 7 8 8 EXT. IN +10 MACRO +10 M2 M3 MACRO M1 REMOTE CONTROL RNC-55A RNC 55A M2 M3 REMOTE CONTROL RNC-50A 5 • Each time the ADJUST DOWN(▼) or CURSOR LEFT(◀) button is pressed, the crossover frequency(“CUT”) changes within the range of 40~130 Hz in 10 Hz intervals. • In case that the subwoofer setting is “S”(Subwoofer:Yes), if it is possible to adjust the volume and crossover frequency on your subwoofer, set the volume to about medium level (or slightly less), and set the crossover frequency to the maximum. Start the auto speaker setup procedure. POWER ON AUD VCR STANDBY ANDBY CD AUX TV DVD SAT SA CBL DEVICE SELECT MEMO/ENTER CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER or SLEEP DIMMER DISPLAY DISPLA RETURN TUNE PRESET P.SCAN STEREO ADJUST SPK SET 1 PRESET DSP AUTO TUNER ENTER TUNE CD 2 VIDEO 1 PARAMATER AUX 3 TAPE 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A Notes: • Because the test tones are very loud, ensure there are no infants or small children in the room. • For best results, ensure the room is as quiet as possible during the auto speaker setup procedure. If there is too much ambient noise, the results may not be satisfactory. • Loud test tones are output from each speaker. • To stop the auto speaker setup procedure, press the (MEMORY/) ENTER button. To retry the procedure, press the (MEMORY/) ENTER button again. •After the auto speaker setup procedure has been completed, “SET MEMO” will be displayed. • If “>ERROR<” is displayed, there may be a problem with the speaker or microphone connection. While displaying “>ERROR<”, to retry the procedure, press the ADJUST UP(▲) or CURSOR RIGHT(▶) button and to exit from the procedure, press the ADJUST DOWN(▼) or CURSOR LEFT(◀) button. • If retrying the procedure does not fix the problem, turn off the power and check the speaker or microphone connections. 23 POWER ON AUD SPEAKER SETUP POWER ON STANDBY CD VCR 7 Confirm the results. AUX DVD AUD TV SAT SA AUX DVD T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP SETUP ENTER ENTER DISPLAY DISPLA RETURN TUNE TUNE P.SCAN ADJUST TUNER CD AUX 2 1 3 VIDEO 1 SLEEP DIMMER DISPLAY DISPLA RETURN TUNE STEREO AUTO PARAMA ARAMATER SPK SET TAPE TUNER 4 1 6 7 9 0 +10 P.SCAN 8 PRESET DSP STEREO ADJUST CD 2 VIDEO 1 VIDEO 2 VIDEO 3 5 PARAMATER AUX 3 6 7 9 0 +10 M1 M3 • Each time this button is pressed, the result changes as follows: • You cannot check the channel level results. To check the channel level results, perform the auto speaker setup procedure, using the OSD menu setting procedure.(For details, refer to “When selecting the AUTO SPEAKER SETUP” on page 42.) • If the results are not satisfactory, set the speaker setup manually.(For details, refer to “SETTING THE SPEAKER SETUP MANUALLY” on page 20.) POWER ON STANDBY CD DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET DSP AUTO STEREO ADJUST SPK SET ADJUST PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 8 M3 • Then “COMPLETE” is displayed and the results are memorized. CENTER L ---- FRONT L 10(ft) FC 80Hz ---- FRONT R 10(ft) VCR M2 REMOTE CONTROL RNC RNC-50A 50A REMOTE CONTROL RNC-50A RNC 50A Example) FRONT L SUB-W Y 4 EXT. IN MACRO MACRO M2 TAPE VIDEO 2 VIDEO 3 5 EXT. IN M1 ENTER TUNE PRESET PRESET DSP SPK SET SPK SET or DIMMER SLEEP PRESET VOLUME MUTE T.TONE .TONE OSD MENU AUTO CBL CH.SEL T/V or TV SAT SA DEVICE SELECT MEMO/ENTER CH.SEL STANDBY ANDBY CD VCR CBL DEVICE SELECT CH/LEVEL ENGLISH 6 While displaying “SET MEMO”, check the result of each adjustment. M3 REMOTE CONTROL RNC-50A 24 Operations ENGLISH • Note : Before operating this receiver with the supplied remote control, refer to “Universal Remote Controls” on page 13 for details about operation. LISTENING TO A PROGRAM SOURCE Before operation • Enter the standby mode. 3 POWER Select the desired input source. POWER ON POWER ON STANDBY CD DVD VCR AUX TV SAT CBL CH.SEL T/V CH/LEVEL • The STANDBY indicator lights up. POWER ON POWER ON AUX TV ※ When the power operation switch is in the OFF or STANDBY state, the apparatus is still connected on some AC line voltages. Please be sure to unplug the cord when you leave home for, say, a vacation. VCR DVD SAT CBL MUTE T.TONE POWER ON INPUT SELECTOR STANDBY CD ON/ OFF AUDIO STANDBY ANDBY AUD CD AUX TV VCR DVD SAT SA CBL OSD MENU SETUP ENTER VIDEO DEVICE SELECT SLEEP DIMMER DISPLAY RETURN TUNE TUNE CH.SEL T/V CH/LEVEL PRESET P.SCAN PRESET VOLUME MUTE CH.SEL T/V CH/LEVEL T.TONE .TONE OSD MUTE T.TONE OSD MENU SETUP MENU ENTER SLEEP DIMMER DISPLAY RETURN TUNE AUTO SETUP P.SCAN DISPLAY DISPLA DSP AUTO 5 PRESET or AUTO 2 3 4 5 6 7 8 9 0 +10 DSP 4 7 8 0 +10 CD AUX TAPE 2 3 4 VIDEO 1 STEREO MACRO ADJUST SPK SET TUNER CD M1 PARAMA ARAMATER TER AUX 2 1 3 M2 5 4 VIDEO 2 VIDEO 3 6 7 0 +10 VIDEO 2 VIDEO 3 M3 TAPE REMOTE CONTROL RNC-50A VIDEO 1 PARAMATER 1 PARAMATER 3 6 1 TUNE P.SCAN 9 STEREO ADJUST SPK SET 2 1 RETURN TUNE PRESET PRESET STEREO ADJUST SPK SET DIMMER TUNE PRESET DSP TUNER ENTER SLEEP 6 7 8 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A MACRO M1 M2 M3 • To switch the power off, push the POWER switch again. • Then the power is cut off and the STANDBY indicator goes off. REMOTE CONTROL RNC-50A • Each time the “AUDIO” button on the front panel is pressed, the input source changes as follows; → TUNER → CD → TAPE → AUX POWER ON STANDBY CD (frequency display) VCR DVD AUX TV SAT CBL CH.SEL 1 In the standby mode, turn the power on. T/V CH/LEVEL MUTE T.TONE OSD • Each time the “VIDEO” button on the front panel is pressed, the input source changes as follows; STANDBY POWER ON MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET POWER ON AUTO DSP ADJUST SPK SET POWER ON POWER ON AUD STANDBY CD AUX TV DVD SAT SA CBL 1 STANDBY PARAMATER 1 2 3 4 5 6 7 8 STANDBY CD STEREO → VIDEO 1 → VIDEO 2 → VIDEO 3 DVD VCR AUX TV SAT CBL CH.SEL T/V 9 0 CH/LEVEL +10 MUTE T.TONE OSD MACRO M1 M2 M3 MENU VCR SETUP ENTER REMOTE CONTROL RNC-50A DEVICE SELECT SLEEP DIMMER DISPLAY RETURN CH.SEL STANDBY T/V CH/LEVEL TUNE VOLUME MUTE TUNE When selecting the EXTERNAL IN as desired, PRESET T.TONE .TONE OSD MENU SETUP ENTER ON/STANDBY SLEEP DIMMER DISPLAY DISPLA RETURN TUNE DSP ADJUST P.SCAN 2 3 4 5 6 7 8 0 +10 9 AUTO DSP STEREO ADJUST PARAMA ARAMATER 1 CD 2 VIDEO 1 5 AUX 3 MACRO INPUT SELECTOR TAPE 4 7 0 +10 M2 M2 M3 STANDBY ANDBY REMOTE CONTROL RNC-50A 8 EXTERNAL IN AUD VCR POWER ON MACRO M1 M1 POWER ON VIDEO 2 VIDEO 3 6 EXT. IN 9 STEREO PARAMATER 1 PRESET SPK SET TUNER PRESET TUNE PRESET or P.SCAN AUTO SPK SET M3 CD AUX TV SAT CBL CD AUX TV DVD SAT SA CBL DEVICE SELECT STANDBY CH.SEL T/V VCR DVD CH/LEVEL VOLUME MUTE REMOTE CONTROL RNC-50A RNC 50A T.TONE .TONE OSD CH.SEL MENU T/V CH/LEVEL SETUP MUTE ENTER or • In the operating mode, if the STANDBY button on the remote control is pressed, the receiver is turned off and enters the standby mode. • In the standby mode, if the INPUT SELECTOR button on the remote control is pressed, the receiver is turned on automatically and the desired input is selected. 2 Switch the speakers on. T.TONE OSD MENU SETUP SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE ENTER PRESET SLEEP P.SCAN PRESET DIMMER DISPLAY 2 EXT. 3 IN 6 7 RETURN TUNE TUNE PRESET P.SCAN PRESET DSP STEREO SPK SET ADJUST PARAMATER 1 DSP AUTO STEREO ADJUST SPK SET AUTO PARAMA ARAMATER TUNER CD AUX TAPE 1 2 3 4 VIDEO 1 5 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 2 1 5 3 4 6 7 8 0 +10 9 8 MACRO 9 M1 MACRO M1 M2 M2 M3 REMOTE CONTROL RNC-50A RNC 50A M3 REMOTE CONTROL RNC-50A • “EXT IN” is displayed and the 7 or 6 separate analog signals from the component connected to this input can be controlled only by channel level(s) and volume depending on the surround back speaker setting. • Press the EXTERNAL IN button or select the desired input source to cancel the external in function. • These analog signals can be heard only, not recorded. SPEAKER POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE ON/OFF OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 7 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A • Then the SPEAKER indicator lights up and the sound can be heard from the speakers connected to the speaker terminals. • When using the headphone for private listening, press the SPEAKER button again to switch the speakers off. POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE 25 OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO 1 PRESET DSP STEREO ADJUST SPK SET 2 PARAMATER 3 4 7 8 7 To compensate for edgy or shrill movie sound tracks. CINEMA EQ Select the digital or analog input connected as desired. 4 ENGLISH When CD, VIDEO 1~3 is selected as an input source DIGITAL INPUTS • Then “C-EQ OFF” is scrolled. • Press it again to work, the “C-EQ ON” is scrolled. • When 96 kHz PCM(2 CH stereo) signals are input or the SPEAKER button is set to off, the cinema EQ function does not work. • Each time this button is pressed, the corresponding input is selected as follows ; A(nalog) o(ptical) 1 o(ptical) 2 c(oaxial) 2 c(oaxial) 1 8 • When TUNER, TAPE, AUX or EXTERNAL IN is selected as an input source, the digital input cannot be selected. To mute the sound. POWER ON AUD STANDBY CD VCR AUX DVD TV SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE Notes : • When the selected optical or coaxial digital input is not connected, the “DIGITAL” indicator flickers, meaning no sound. (Refer to “ENJOYING SURROUND SOUND” on page 30.) • The sound from the component connected to the selected digital input can be heard regardless of the selected input source. SETUP ENTER DIMMER SLEEP DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN PRESET DSP AUTO STEREO ADJUST SPK SET TUNER CD 3 VIDEO 1 5 PARAMATER AUX 2 1 TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A • “MUTE” will flicker. • To resume the previous sound level, press it again. POWER ON STANDBY CD VCR T.TONE DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE Operate the selected component for playback. 5 MUTE OSD MENU OSD To listen with the headphones. MENU SETUP ENTER 9 MENU SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET PHONES P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A • When playing back the program sources with surround sound, refer to “ENJOYING SURROUND SOUND” on page 30. Adjust the (overall) volume. 6 POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE • Ensure that the SPEAKER button is set to off. • Depending on the signal format which P.SCANis being input, you can listen in different Dolby Headphone modes, stereo mode, etc. with pressing the DSP MODE ◀(<) /▶(>) buttons.(For details, refer to “Listening in a Dolby Headphone mode” on page 31). T.TONE OSD MENU SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET POWER ON MASTER VOLUME STANDBY AUD CD AUX TV VCR DVD SAT SA CBL DEVICE SELECT P.SCAN AUTO DSP SPK SET ADJUST T/V VOLUME MUTE T.TONE .TONE VOLUME 2 3 4 5 6 7 8 0 +10 MACRO M1 OSD MENU SETUP DIMMER SLEEP DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN TUNER 1 UP STEREO ADJUST CD 2 VIDEO 1 5 M3 PRESET DSP AUTO SPK SET DOWN M2 REMOTE CONTROL RNC-50A ENTER or STEREO PARAMATER 1 9 CH.SEL CH/LEVEL PRESET PARAMA ARAMATER AUX 3 TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE 26 SLEEP OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE PRESET DISPLAY TUNE P.SCAN PRESET AUTO DSP STEREO SPK SET ADJUST PARAMATER ENGLISH Adjusting the tone(bass and treble) 11 Enter the tone mode. 10 At the desired tone mode, adjust the tone as desired. ADJUST TONE MODE • At “TONE ON” mode, you can select “TONE OFF” mode and vice versa. TONE ON : When adjusting the tone for your taste. (“DIRECT” indicator goes off.) TONE OFF : When listening to a program source without the tone effect. (“DIRECT” indicator lights up.) • Each time this button is pressed, the corresponding tone mode is selected and shown for several seconds as follows: BASS TRBL(treble) TONE ON • In general, we recommend the bass and the treble to be set to 0(flat) level. • When the tone mode is off, “TONE OFF” is shown. Notes: • If the tone display disappears, start from the step ⑩ again. • Extreme settings at high volume may damage your speakers. • When the digital signals from DTS, Dolby Digital or MPEG program sources are input or the EXTERNAL IN is selected as an input source, you cannot adjust the tone and can hear a program source without the tone effect. 27 SURROUND SOUND Surround modes • DTS Neo : 6 Cinema This mode is optimum for playing movies. Decoding is performed with emphasis on separation performance to achieve the same atmosphere with 2-channel sources as with 6.1-channel sources. ■DTS Digital Surround DTS Digital Surround(also called simply DTS) is a multichannel digital signal format which can handle higher data rates. Discs bearing the “ ” include the recording of up to 5.1 channels of digital signals, which can be generally thought to provide better sound quality due to the lower audio compression required. It also provides wide dynamic range and separation, resulting in magnificent sound. ■DTS - ES Extended Surround™ ( • DTS Neo : 6 Music This mode is suited mainly for playing music. The front left and front right signals bypass the decoder and are played directly so there is no loss of sound quality, and the effect of the surround signals from the center, surround left, surround right and surround back channels adds a natural sense of expansion to the sound field. ) This is a new multi channel digital signal format which greatly improves the 360- degree surround impression and space expression thanks to further expanded surround signals, offering high compatibility with the conventional DTS format. In addition to the 5.1 channels, DTS-ES Extended Surround also offers the surround back (sometimes also referred to as “surround center”) channel for surround playback with a total of 6.1 channels. DTS-ES Extended Surround includes two signal formats with different surround signal recording methods as follows: ■DTS 96/24 Conventional surround formats used sampling frequencies of 48 or 44.1 kHz, so 20 kHz was about the maximum playback signal frequency. With DTS 96/24, the sampling frequency is increased to 96 or 88.2 kHz to achieve a wide frequency range of over 40 kHz. In addition, this format has a resolution of 24 bits, resulting in the same frequency band and dynamic range as 96kHz / 24 bit PCM signals. As with conventional DTS surround, DTS 96/24 is compatible with a maximum of 5.1 channels. DTS 96/24 is fully compatible with the conventional DTS surround format, so DTS 96/24 sources can be played using a conventional DTS 5.1 channel decoder. • DTS-ES™ Discrete 6.1 Because the signals for 6.1 channels (including the surround back channel) are fully independent, it is possible to achieve a sense that the acoustic image are moving about freely among the background sounds surrounding the listener from 360 degrees. Though maximum performance is achieved when sound tracks recorded with this system are played using a DTS -ES decoder, when played with a conventional DTS decoder, the surround back channel signals are automatically downmixed to the surround left and surround right channels so that none of the signal components are lost. “DTS”, “DTS-ES”, “DTS 96/24” and “Neo:6” are trademarks of Digital Theater Systems, Inc. ■Dolby Digital Dolby Digital is the multi- channel digital signal format developed by Dolby Laboratories. Discs bearing the “ DOLBY ” includes the recording of up to 5.1 channels of • DTS - ES™ Matrix 6.1 With this format, the additional surround back channel signals undergo matrix encoding and are input to the surround left and surround right channels beforehand. During playback, they are decoded to the surround left, surround right and surround back channels. Because the bit stream format is 100% compatible with conventional DTS signals, the effect of the DTS-ES Matrix 6.1 format can be achieved even with DTS 5.1- channel signal sources. Of course, it is possible to play DTS-ES Matrix 6.1 channel signal sources with a DTS 5.1 - channel decoder. When DTS-ES Discrete 6.1 or Matrix 6.1 sources are decoded with a DTS - ES decoder, the format is automatically detected upon decoding and the optimum surround mode is selected. However, some DTS - ES Matrix 6.1 sources may be detected as DTS sources. In this case, the DTS - ES Matrix mode should be selected manually to play these sources. D I G I T A L digital signals, which can reproduce much better sound quality, spatial expansion and dynamic range characteristics than the previous Dolby Surround effect. ■Dolby Digital EX This mode creates the back (sometimes also referred to as “surround center”) signals from the surround left and right signals in Dolby Digital 5.1 channel source using a matrix decoder and provides 6.1 channel surround playback. For the best results, this mode should be selected during playback of DOLBY ”) recorded in Dolby Digital sources(bearing the “ EX. With this additional channel, you can experience more dynamic and realistic moving sound especially. When Dolby Digital EX sources are decoded with a Dolby Digital EX decoder, the format is automatically detected upon decoding and the Dolby Digital EX mode is selected. However, some Dolby Digital EX sources may be detected as Dolby Digital sources. In this case, the Dolby Digital EX mode should be selected manually to play these sources. DTS Neo : 6™ surround This mode applies conventional 2-channel signals such as digital PCM or analog stereo signals to the high precision digital matrix decoder used for DTS-ES Matrix 6.1 to achieve 6.1channel surround playback. DTS Neo : 6 surround includes two modes for selecting the optimum decoding for the signal source. 28 ENGLISH • This receiver incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound atmosphere in your personal Home Theater. ENGLISH ■Dolby Pro Logic IIx surround ■Dolby Headphone Dolby Pro Logic IIx decodes all stereo (2 channel ) and 5.1 channel sources and extends to 7.1channel surround playback. It delivers the most natural, full range and immersing 7.1 channel listening experience. Dolby Pro Logic IIx surround includes two modes as follows : The Dolby Headphone function simulates 5.1 channel surround sound, which allows you to enjoy 5.1 channel surround sound through 2 channel headphones, just like listening from 5.1 channel speakers. This mode is effective not only for 5.1 channel sources but also for stereo(2 channel) sources. • Dolby Pro Logic IIx Movie When enjoying movies, this mode allows you to further enhance the cinematic quality by adding processing that emphasizes the sounds of the action special effects. Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. • Dolby Pro Logic IIx Music When listening to music, this mode allows you to further enhance the sound quality by adding processing that emphasizes the musical effects. ■MPEG Multichannel This mode is a surround system which faithfully reproduces the ambience and dynamics of movie soundtracks and music alike. Though the number of audio channels are same as Dolby Digital, discs bearing the “ ” provides much better at locating individual sounds to the correct and stable position in the sound stage. ■Dolby Pro Logic II surround This mode applies conventional 2-channel signals such as digital PCM or analog stereo signals as well as Dolby Surround signals, etc. to surround processing to offer improvements over conventional Dolby Pro Logic circuits. Dolby Pro Logic II surround includes Dolby Pro Logic II Movie and Dolby Pro Logic II Music like Dolby Pro Logic IIx surround. • The following modes apply conventional 2-channel signals such as digital PCM or analog stereo signals to high performance Digital Signal Processor to recreate sound fields artificially. Select one of the 3 provided surround modes according to the program source you want to play. ■Dolby Virtual Speaker This mode creates a virtual surround sound field using as few as two front speakers, allowing you to experience listening from 5.1 channel speakers. This mode is effective not only for 5.1 channel sources but also for stereo(2 channel) sources. Dolby VIrtual Speaker includes two listening mode as follows: ■Theater This mode provides the effect of being in a movie theater when watching a movie. ■Hall This mode provides the ambience of a concert hall for classical music sources such as orchestral, chamber music or an instrumental solo. • Dolby Virtual Speaker Reference The width of the front sound image is defined by the actual distance between front speakers. ■Stadium • Dolby Virtual Speaker Wide The width of the front sound image seems to extend beyond the front speakers. This mode provides the expansive sound field to achieve the true stadium effect when watching baseball or soccer games. • When using the EXTERNAL INs to play back the sound from the additional multi-channel decoder for surround sound, you can enjoy the corresponding surround sound, too.( For details, refer to the operating instructions of the component to be connected.) For your reference, the sound from each channel can be reproduced according to the surround modes as follows: Modes Channels FRONT L/R CENTER SURROUND L/R SURROUND BACK SUBWOOFER — DTS, DTS 96/24 DTS ES DISCRETE/MATRIX —(*) DTS NEO 6: CINEMA/MUSIC — DOLBY DIGITAL DOLBY DIGITAL EX —(*) DOLBY PRO LOGIC IIx MOVIE/MUSIC DOLBY PRO LOGIC II MOVIE/MUSIC — —(*) DOLBY VIRTUAL SPEAKER — —(*) MPEG — —(*) Other Surrounds STEREO — — — —(*) EXTERNAL IN (*): Depending on the subwoofer mode setting, the sound from the subwoofer channel may be reproduced. • Depending on the speaker settings and the number of the encoded channels, etc., the sound from the corresponding channels cannot be reproduced.(For details, refer to “Speaker Setup” on page 19.) 29 • Surround sound effect will not work properly if the signal passes through a graphic equalizer. Please refer to your equalizer operating instructions for guidance on switching off (or defeating) the equalizer. Note: • Before surround playback, first perform the SPEAKER SETUP procedure, etc. for optimum performance. (For details, refer to “Speaker Setup” on page 19.) 1 Depending on the input digital signal format, select the desired decoding mode. • Each time the AUTO button is pressed, the decoding mode changes as follows : SURROUND MODE POWER ON AUD AUTO STANDBY CD VCR DVD AUX TV SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD IN-AUTO : The input digital signal format(DTS, Dolby Digital, MPEG or PCM(2 channel stereo), etc.) used by the selected digital input source is detected automatically to perform the necessary decoding process for optimum surround mode. IN-DTS : The DTS signal processing is performed only when DTS signals are input. IN-PCM : The PCM signal processing is performed only when PCM AUTO signals are input. POWER ON MENU SETUP STANDBY CD or ENTER VCR SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE DVD AUX TV SAT CBL CH.SEL PRESET P.SCAN PRESET T/V CH/LEVEL MUTE T.TONE DSP AUTO STEREO OSD MENU ADJUST SPK SET PARAMA ARAMATER SETUP ENTER AUTO TUNER 1 CD 2 VIDEO 1 5 AUX TAPE 3 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 ■Notes : • Only when the digital input is selected as signal input for the input sources except TUNER, TAPE, AUX and EXTERNAL IN, the decoding mode can be selected. • Noise may be generated at the beginning of playback and while searching during DTS playback in the IN-AUTO mode. In this case, try playing in the IN-DTS mode. MACRO M1 M2 M3 REMOTE CONTROL RNC-50A POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL Select the desired surround mode. T/V CH/LEVEL MUTE T.TONE 2 SURROUND MODE OSD MENU SETUP POWER ON AUD ENTER SLEEP DIMMER DISPLAY RETURN DSP MODE STANDBY ANDBY CD VCR AUX DVD TV SAT SA CBL DEVICE SELECT TUNE TUNE CH.SEL PRESET P.SCAN T/V PRESET CH/LEVEL VOLUME MUTE T.TONE .TONE DSP AUTO 2 1 5 9 PARAMATER 3 6 7 0 +10 MENU DSP M2 SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN 4 8 TUNE TUNE PRESET MACRO M1 OSD STEREO ADJUST SPK SET M3 • Each time the DSP MODE ◀(<) or ▶(>) button is pressed, the surround mode changes depending on the input signal format and the selected decoding mode as follows : or P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMA ARAMATER REMOTE CONTROL RNC-50A Signal format being input Dolby Digital EX 6.1 channel sources Dolby Digital 5.1 channel sources Dolby Digital 2 channel sources POWER ON STANDBY CD VCR DVD AUX TV SAT CBL Selected decoding mode IN-AUTO mode CH.SEL T/V CH/LEVEL MUTE T.TONE OSD TUNER CD AUX 2 1 3 VIDEO 1 6 7 9 0 +10 SETUP MACRO M1 M2 M3 Selectable surround mode DOLBY DIGITAL EX, DOLBY D VS REF, DOLBY D VS WIDE <DOLBY D PL IIx MUSIC>, DOLBY DIGITAL, DOLBY D VS REF, DOLBY D VS WIDE <DOLBY D PL IIx MOVIE, DOLBY D PL IIx MUSIC,> / [DOLBY D PL II MOIVE, DOLBY D PL II MUSIC,] DOLBY PRO LOGIC, DOLBY D VS REF, DOLBY D VS WIDE (DTS +NEO: 6,) corresponding DTS mode, DOLBY VS REF, DOLBY VS WIDE MPEG STEREODOLBY VS [DOLBY PL II MOVIE,] DOLBY PL II MUSIC, DOLBY PRO LOGIC, REF, DOLBY VS WIDE <DOLBY PL IIx MOVIE, DOLBY PL IIx MUSIC,> / [DOLBY PL II MOVIE, DOLBY PL II MUSIC,] DOLBY PRO LOGIC, DOLBY VS REF, DOLBY VS WIDE, NEO: 6 CINEMA, NEO: 6 MUSIC, THEATER, HALL, STADIUM VCR DIMMER RETURN TUNE 8 REMOTE CONTROL RNC-50A RNC 50A STANDBY CD ENTER SLEEP 4 EXT. IN POWER ON MENU DISPLAY TUNE DSP TAPE VIDEO 2 VIDEO 3 5 DVD AUX TV SAT CBL CH.SEL PRESET P.SCAN T/V PRESET CH/LEVEL MUTE T.TONE DSP AUTO DTS sources MPEG sources 96 kHz PCM(2 channel) sources 1 5 9 STEREO ADJUST SPK SET 2 PARAMATER 3 6 7 0 +10 4 8 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A STEREO IN-AUTO, IN-DTS mode IN-AUTO mode IN-AUTO, IN-PCM mode SETUP ENTER SLEEP DIMMER RETURN TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 PCM( 2 channel ) sources Analog stereo sources OSD MENU DISPLAY MACRO M1 M2 M3 REMOTE CONTROL RNC-50A - • Depending on surround back speaker setting, some surround modes can be selected or not as follows: < >: Possible only when surround back speaker is not set to “None”. [ ] : Possible only when surround back speaker is set to “None”. ( ): Possible only when surround back speaker is not set to “None” while playing the digital signals from DTS sources except DTS ES 6.1 channel sources. ■Notes: • When the selected decoding mode is not matched to the input signal format, the “DIGITAL” indicator flickers and no sound is heard. Therefore, be sure to select the required decoding mode and the available surround mode according to the input signal format. • When the EXTERNAL IN is selected as an input source, the decoding and surround modes cannot be selected. • When the digital signals are not inputted, the desired surround mode cannot be selected. 30 ENGLISH ENJOYING SURROUND SOUND CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN Continued PRESET DSP AUTO STEREO ADJUST SPK SET 1 2 5 9 DSP PARAMATER 3 4 6 7 8 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A To cancel the surround mode for stereo operation POWER ON AUD STERO • Depending on the signal format which is being input, either the stereo mode or the 2CH downmix mode is selected. • To cancel either the stereo mode or the 2 CH downmix mode, select the desired surround mode with using the DSP MODE ◀(<) or ▶(>) button. STANDBY CD AUX DVD VCR TV SAT CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE ENGLISH T.TONE .TONE OSD MENU SETUP ENTER DIMMER SLEEP or DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET DSP AUTO STEREO ADJUST SPK SET TUNER CD TAPE 3 VIDEO 1 STEREO PARAMA ARAMATER TER AUX 2 1 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A 2CH downmix mode • This mode allows the multi-channel signals encoded in DTS, Dolby Digital or MPEG format to be mixed down into 2 front channels and to be reproduced through only two front speakers or through headphones. • When the SPEAKER button is set to off to listen with headphones, if the STEREO button is pressed while playing the multichannel digital signals from DTS or Dolby Digital sources, it will enter the 2 CH downmix mode automatically. • To cancel the 2 CH downmix mode, select the desired Dolby Headphone mode with using the DSP MODE ◀(<) or ▶(>) button.(For details, refer to the following “Listening in a Dolby Headphone mode” procedure.) POWER ON STANDBY CD DVD VCR AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP Listening in a Dolby Headphone mode ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO • The Dolby Headphone function simulates 5.1 channel surround sound, which allows you to enjoy 5.1 channel surround sound through 2 channel headphones, just like listening from 5.1 channel speakers. ■Note : Only when the SPEAKER button is set to off, the Dolby Headphone mode can be selected. However, in case of playing the digital signals from MPEG source, either the stereo mode or the 2CH downmix mode will be automatically selected depending on its signal format. • While listening with headphones, select the desired Dolby Headphone mode. ADJUST SPK SET AUTO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A SURROUND MODE POWER ON DSP MODE • Each time the DSP MODE ◀(<) or ▶(>) button is pressed, the mode changes as follows : STANDBY ANDBY AUD CD AUX TV VCR DVD SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET or P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET TUNER CD TAPE 3 VIDEO 1 DSP PARAMA ARAMATER TER AUX 2 1 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 → DH 1 : This simulates the soundfield as if you were in a relatively small room with less reverberations. DH 2 : This simulates the soundfield as if you were in a typical listening room with moderate reverberations. → DH 3 : This simulates the soundfield as if you were in a large space like theater. REMOTE CONTROL RNC-50A RNC 50A ■In case of playing analog stereo, PCM 2 channel or Dolby Digital 2 channel source in a Dolby Headphone mode, press the PARAMETER button to select the desired listening mode. POWER ON • Each time this button is pressed, the mode changes as follows : STANDBY CD AUX DVD VCR TV SAT CBL POWER ON AUD → MOVIE : This provides the surround effect suitable for movie sources. STANDBY ANDBY CD AUX TV SAT SA CBL CH.SEL T/V DVD VCR CH/LEVEL MUTE DEVICE SELECT T.TONE OSD CH.SEL T/V MENU CH/LEVEL SETUP VOLUME MUTE ENTER T.TONE .TONE SLEEP OSD DIMMER MENU DISPLAY MUSIC 1 : This provides the surround effect suitable for music sources. SETUP RETURN TUNE TUNE ENTER PRESET or P.SCAN PRESET SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE AUTO DSP PRESET STEREO P.SCAN PRESET ADJUST SPK SET 2 1 AUTO 5 SPK SET 9 TUNER 6 0 4 STEREO 7 TAPE AUX 3 4 VIDEO 2 VIDEO 3 6 7 M2 8 M3 9 MUSIC 2 : This provides less surround effect compared to MUSIC 1 mode. PARAMA ARAMATER TER +10 2 VIDEO 1 MACRO 5 8 ADJUST CD 1 M1 STEREO PARAMATER PARAMATER 3 DSP 0 EXT. IN +10 REMOTE CONTROL RNC-50A MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A Adjusting the Dolby Pro Logic IIx/Dolby Pro Logic II Music parameters • When selecting the Dolby Pro Logic IIx Music mode or the Dolby Pro Logic II Music mode, you can adjust the various surround parameters for optimum surround effect. 1 Press the PARAMETER button to select the desired parameter. POWER ON AUD STANDBY ANDBY CD AUX DVD VCR TV SAT CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER or DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET PARAMATER DSP AUTO TUNER 1 CD 2 VIDEO 1 5 STEREO ADJUST SPK SET 6 PARAMA ARAMATER TER AUX 3 TAPE 4 VIDEO 2 VIDEO 3 7 8 EXT. IN 9 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A • Each time this button is pressed, the parameter changes and is displayed for several seconds as follows; ※Panorama mode(“PANO”, default value : OFF) This mode extends the front stereo image to include the surround speakers for an exciting “wraparound” effect with side wall imaging. Select “OFF” or “ON”. ※Center width control(“C-WID”, default value : 0) This adjusts the center image so it may be heard only from the center speaker, only from the left/right speakers as a phantom image, or from all three front speakers to varying degrees. The control can be set in 8 steps from 0 to 7. ※Dimension control(“DIMEN”, default value : -1) This gradually adjusts the soundfield either towards the front or towards the rear. The control can be set in 7 steps from -4 to +2. 31 DSP AUTO STEREO ADJUST SPK SET SPK SET PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A POWER ON ADJUST AUD STANDBY CD VCR 3 Repeat the above steps ① and ② to adjust other parameters. ENGLISH 2 At the desired parameter, adjust it as desired. AUX DVD TV SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE or OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET ADJUST P.SCAN AUTO DSP SPK SET ADJUST TUNER 1 CD 2 VIDEO 1 5 PRESET STEREO PARAMA ARAMATER AUX 3 TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A • If the parameter display disappears, start from the step ① again. Selecting the desired speaker layout for Dolby Virtual Speaker mode • When selecting the Dolby Virtual Speaker Reference mode(“DOLBY (D) VS REF”) or the Dolby Virtual Speaker Wide mode(“DOLBY (D) VS WIDE”), you can select the desired one of different speaker layouts for actual speakers to be used. • Press the PARAMETER button to select the desired speaker layout. • Each time this button is pressed, the speaker layout mode changes depending on the selected Dolby Virtual Speaker mode as follows: POWER ON AUD STANDBY CD VCR DVD AUX TV SAT SA CBL * In case of Dolby Virtual Speaker Reference mode, DEVICE SELECT 2 SPK : When using 2 front speakers only CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER or 3 SPK : When using 2 front and center speakers DIMMER SLEEP DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN PRESET PARAMATER AUTO DSP STEREO SPK SET ADJUST PARAMATER TER TUNER CD AUX 2 1 3 VIDEO 1 → 2 SPK : When using 2 front speakers only TAPE 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 * In case of Dolby Virtual Speaker Wide mode, 8 EXT. IN MACRO M1 M2 M3 3 SPK : When using 2 front and center speakers REMOTE CONTROL RNC-50A RNC 50A 4 SPK : When using 2 front and 2 surround speakers 5 SPK : When using 2 front, center and 2 surround speakers ■Note : When the speakers are set to “None”, the corresponding speaker layout modes cannot be selected. POWER ON STANDBY CD VCR DVD AUX TV SAT CBL MUTE CH.SEL T/V CH/LEVEL Adjusting each channel level with test tone MUTE T.TONE OSD MENU SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE • The volume level of each channel can be adjusted easily with the test tone function. ■Note : When the EXTERNAL IN is selected as an input source, the SPEAKER button is set to off or it is in the stereo mode, the test tone function does not work. PRESET P.SCAN PRESET DSP AUTO STEREO ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A 1 Enter the test tone mode. • The test tone will be heard from the speaker of each channel for 2 seconds as follows: POWER ON STANDBY AUD CD AUX TV VCR DVD SAT SA CBL FL C FR SR SB Front Left Center Front Right Surround Right Surround Back DEVICE SELECT T.TONE SW CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU Subwoofer SETUP ENTER DIMMER SLEEP MENU DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST TUNER 1 CD 2 VIDEO 1 PRESET • When the speaker setting is “N”, the test tone of the corresponding channel is not available. STEREO PARAMA ARAMATER TER AUX 3 TAPE 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 SL Surround Left M2 M3 REMOTE CONTROL RNC RNC-50A 50A 32 POWER ON STANDBY TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 POWER ON STANDBY CD VCR DVD AUX TV SAT CBL MACRO M1 M2 MUTE CH.SEL M3 T/V CH/LEVEL MUTE REMOTE CONTROL RNC-50A T.TONE OSD MENU SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN POWER ON VCR STANDBY AUX TV SAT CBL 9 T/V 2 T.TONE OSD MENU SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN 2 3 5 6 7 0 +10 M1 0 +10 4 8 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A 4 8 POWER ON MACRO AUD CH/LEVEL 7 PARAMATER 1 9 6 STEREO ADJUST SPK SET ADJUST PRESET DSP AUTO ENGLISH 3 MUTE PARAMATER 3 Cancel the test tone function. 5 CH.SEL CH/LEVEL 2 1 At each channel, adjust the level as desired until the sound level of each speaker is heard to be equally loud. STEREO ADJUST SPK SET CD DVD PRESET DSP AUTO STANDBY CD M2 M3 VCR DVD AUX TV SAT SA CBL REMOTE CONTROL RNC-50A DEVICE SELECT POWER ON CH.SEL AUD STANDBY ANDBY CD AUX TV T/V CH/LEVEL VOLUME MUTE VCR T.TONE .TONE OSD MENU ADJUST DVD SAT SA CBL DEVICE SELECT SETUP T.TONE ENTER CH.SEL T/V CH/LEVEL VOLUME MUTE DIMMER SLEEP T.TONE .TONE DISPLAY DISPLA OSD RETURN TUNE TUNE PRESET P.SCAN MENU SETUP PRESET ENTER DSP AUTO or TUNER CD RETURN TUNE TUNE P.SCAN PRESET TAPE 3 VIDEO 1 DIMMER PRESET PARAMA ARAMATER AUX 2 1 MENU STEREO ADJUST SPK SET SLEEP DISPLAY DISPLA 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 AUTO DSP SPK SET ADJUST STEREO EXT. IN TUNER CD M3 5 TAPE 3 VIDEO 1 M2 PARAMATER AUX 2 1 MACRO M1 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 REMOTE CONTROL RNC-50A RNC 50A MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A • You can select the desired channel and adjust its level with repeating the steps ① and ② in “Adjusting the current channel level” procedure. POWER ON STANDBY CD VCR AUX TV SAT CBL DVD CH/LEVEL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET DSP AUTO STEREO Adjusting the current channel level ADJUST SPK SET 2 5 6 3 7 0 +10 STANDBY 8 CD VCR STANDBY CD 4 POWER ON 9 POWER ON PARAMATER 1 DVD AUX TV SAT CBL VCR DVD AUX TV SAT CBL CH.SEL CH.SEL T/V T/V CH/LEVEL MUTE • After adjusting each channel level with test tone, adjust the channel levels either according to the program sources or to suit your tastes. P.SCAN • You can adjust the current channel levels as desired. These adjusted levels are just memorized into user’s memory(“USER”), not into preset memory(“REF. 1”, “REF. 2”). MACRO M1 M2 M3 T.TONE CH.SEL OSD T/V CH/LEVEL MENU MUTE SETUP REMOTE CONTROL RNC-50A ENTER T.TONE OSD MENU SETUP SLEEP DIMMER DISPLAY RETURN TUNE ENTER PRESET DIMMER SLEEP DISPLAY TUNE P.SCAN PRESET RETURN TUNE TUNE PRESET P.SCAN PRESET DSP AUTO PARAMATER STEREO ADJUST SPK SET STEREO ADJUST SPK SET DSP AUTO PARAMATER 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 0 +10 9 MACRO 9 0 M1 +10 M2 M3 REMOTE CONTROL RNC-50A MACRO Press the CHANNEL SELECTOR button. M1 M2 M3 REMOTE CONTROL RNC-50A 1 POWER ON CHANNEL SELECTOR CD AUX TV VCR DVD SAT SA CBL • Each time this button is pressed, “REF. 1” (or “USER”) is displayed and the corresponding channel is selected as follows: CH.SEL STANDBY AUD T/V DEVICE SELECT POWER ON STANDBY CH.SEL CD T/V CH/LEVEL AUX TV VOLUME MUTE VCR DVD SAT T.TONE .TONE OSD MENU SETUP CBL REF. 1(or USER) FL <DTS L or DD L> CH.SEL or T/V ENTER CH/LEVEL MUTE DIMMER SLEEP T.TONE OSD DISPLAY DISPLA RETURN TUNE TUNE MENU PRESET SETUP P.SCAN POWER ON PRESET DTS LFE DIMMER SLEEP AUTO DSP DISPLAY STEREO RETURN TUNE TUNE SPK SET ADJUST PRESET STANDBY CD ENTER AUX TV C FR SW SR SL SB Dolby Digital LFE VCR DVD PARAMA ARAMATER TER P.SCAN PRESET SAT CBL CH.SEL T/V TUNER 1 CD TAPE AUX 2 VIDEO 1 5 3 CH/LEVEL 7 T.TONE 8 DSP 0 SET SPK OSD < >: Possible only when the digital signals from Dolby Digital or DTS SLEEP program sources that include LFE signal are input. STEREO EXT. IN 9 ADJUST MUTE 4 VIDEO 2 VIDEO 3 6 AUTO MENU +10ADJUST PARAMATER SETUP ENTER 2 1 MACRO M1 M2 M3 5 6 3 4 7 8 DIMMER SLEEP DISPLAY RETURN TUNE 9 0RNC-50A +10 REMOTE CONTROL RNC 50A DISPLAY MACRO M1 M2 TUNE PRESET M3 REMOTE CONTROL RNC-50A P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER • Depending on the speaker setting and surround mode, etc., some channels cannot be selected. • When the SPEAKER button is set to off, only the front L/R channel can be selected. 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A 2 Adjust the level of the selected channel as desired. • The LFE level can be adjusted within the range of -10~0 dB and other channel levels within the range of -15~+15 dB. • In general, we recommend the LFE level to be DIMMER adjusted to 0 dB.(However, the recommended LFE level for some early DTS software is -10 dB.) If the RETURN recommended levels seem too high, lower the setting as necessary. • If the channel display disappears, start from the step ① again. POWER ON POWER ON STANDBY AUD CD AUX TV VCR DVD SAT SA CBL CH/LEVEL VCR AUX TV SAT CBL CH.SEL DEVICE SELECT T/V CH/LEVEL CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE T.TONE OSD SETUP ENTER SETUP ENTER DIMMER SLEEP MUTE MENU OSD MENU ADJUST STANDBY CD DVD SLEEP DIMMER DISPLAY RETURN TUNE DISPLAY DISPLA RETURN TUNE P.SCAN or PRESET DSP STEREO ADJUST SPK SET TUNER CD VIDEO 1 PARAMA ARAMATER AUX TAPE 3 4 2 1 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 TUNE PRESET TUNE PRESET AUTO DSP ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 8 EXT. IN P.SCAN AUTO SPK SET MACRO M1 MACRO M1 M2 M3 M2 M3 REMOTE CONTROL RNC-50A REMOTE CONTROL RNC-50A RNC 50A 3 Repeat the above steps ① and ② to adjust each channel level. POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE PRESET AUTO TUNE P.SCAN DSP PRESET STEREO 33 • You can memorize the adjusted channel levels into preset memory(“REF. 1”, “REF. 2”) and recall the memorized whenever you want. 1 After performing the steps ①~③ in “Adjusting the current channel level” procedure on page 33, press the (MEMORY/) ENTER button. POWER ON POWER ON AUD STANDBY STANDBY CD CD AUX TV DVD SAT SA CBL VCR VCR DVD AUX TV SAT CBL DEVICE SELECT MEMO/ENTER CH.SEL T/V CH.SEL T/V CH/LEVEL CH/LEVEL MUTE VOLUME MUTE T.TONE T.TONE .TONE OSD OSD MENU MENU SETUP SETUP ENTER ENTER or DISPLAY DISPLA DIMMER RETURN TUNE RETURN TUNE SLEEP DISPLAY ENTER DIMMER SLEEP TUNE TUNE PRESET PRESET P.SCAN DSP STEREO ADJUST PARAMA ARAMATER ADJUST TUNER 1 CD 2 TAPE ON AUX POWER 3 6 STANDBY AUX TV SAT CBL VIDEO 2 VIDEO 3 7 DVD EXT. IN 0 DSP ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 • The “1” of “REF. 1” indication flickers. 8 VCR 9 AUTO SPK SET 4 CD VIDEO 1 5 P.SCAN PRESET AUTO SPK SET 9 +10 MACRO CH.SEL MACRO M1 M2 M3 T/V M1 M2 M3 CH/LEVEL MUTE REMOTE CONTROL RNC-50A T.TONE REMOTE CONTROL RNC-50A RNC 50A OSD MENU SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN DSP AUTO 2 STEREO ADJUST SPK SET ADJUST PRESET PARAMATER Select the desired one of REF. 1 and REF. 2. 1 2 3 4 5 6 7 8 9 0 +10 3 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A Confirm your selection. POWER ON AUD DVD AUX TV SAT SA CBL DEVICE SELECT MEMO/ENTER STANDBY STANDBY CD VCR POWER ON CH.SEL T/V AUD CD AUX TV CH/LEVEL VCR DVD SAT SA VOLUME MUTE CBL T.TONE .TONE CH/LEVEL OSD DEVICE SELECT MENU SETUP CH.SEL ENTER T/V CH/LEVEL ADJUST or VOLUME MUTE T.TONE .TONE OSD MENU SETUP SLEEP DIMMER DISPLAY DISPLA RETURN TUNE ENTER TUNE PRESET P.SCAN PRESET ENTER DIMMER SLEEP DSP AUTO DISPLAY DISPLA POWER ON STANDBY RETURN TUNE TUNE ADJUST SPK SET PRESET P.SCAN VCR 1 CD 2 VIDEO 1 AUTO DSP STEREO SPK SET ADJUST PARAMATER TER CD AUX TV DVD SAT CBL PARAMATER PRESET TUNER or STEREO AUX TAPE 3 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 CH.SEL EXT. IN T/V TUNER POWER ON STANDBY CD AUX 2 1 3 AUX TV SAT CBL TAPE 5 M2 7 0 +10 OSD M3 VIDEO 2 VIDEO 3 6 MUTE T.TONE MACRO 4 M1 VIDEO 1 CD DVD CH/LEVEL MENU SETUP 8 EXT. IN VCR 9 CH/LEVEL CH.SEL M1 M2 ENTER REMOTE CONTROL RNC-50A RNC 50A MACRO SLEEP DIMMER DISPLAY RETURN TUNE TUNE M3 T/V PRESET CH/LEVEL P.SCAN PRESET MUTE REMOTE CONTROL RNC-50A RNC 50A T.TONE OSD MENU SETUP ENTER ADJUST RETURN TUNE P.SCAN DSP ADJUST STEREO PARAMATER • The adjusted channel levels have now been memorized into the selected memory. DIMMER SLEEP DISPLAY TUNE PRESET AUTO SPK SET PRESET 1 2 3 4 5 6 7 8 0 +10 9 MACRO DSP AUTO STEREO ADJUST SPK SET M1 M2 M3 PARAMATER REMOTE CONTROL RNC-50A 1 2 3 4 5 6 7 8 9 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A Recalling the memorized channel levels POWER ON STANDBY CD VCR DVD AUX TV SAT CBL 2 CH.SEL Press the CHANNEL SELECTOR button. T/V Select the desired one of REF. 1 and REF. 2. CH.SEL 1 T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET POWER ON AUD AUTO DSP SPK SET ADJUST VCR CHANNEL SELECTOR STANDBY AUD CD AUX TV VCR DVD SAT SA CBL 1 5 9 2 3 6 7 0 +10 8 CH/LEVEL M2 VOLUME MUTE T.TONE .TONE T/V M1 CBL T/V OSD MENU ADJUST M3 T/V SETUP ENTER VOLUME MUTE TV SAT SA CH.SEL MACRO CH.SEL AUX DVD DEVICE SELECT 4 CH.SEL DEVICE SELECT CH/LEVEL STANDBY ST ANDBY CD STEREO PARAMATER CH/LEVEL POWER ON SLEEP DIMMER DISPLAY DISPLA RETURN REMOTE CONTROL RNC-50A T.TONE .TONE OSD TUNE MENU or SETUP TUNE PRESET P.SCAN PRESET ENTER DIMMER SLEEP DSP AUTO DISPLAY DISPLA RETURN TUNE or TUNE PRESET P.SCAN PRESET TUNER CD 2 1 3 TUNER CD TAPE 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 STEREO ADJUST SPK SET PARAMATER AUX VIDEO 1 DSP AUTO STEREO ADJUST SPK SET 8 EXT. IN PARAMATER AUX TAPE 3 4 MACRO 1 2 VIDEO 1 M1 M2 M3 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN REMOTE CONTROL RNC-50A RNC 50A MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A • “REF.1” (or “USER”) is displayed for several seconds. • If the channel level mode display disappears, press the CHANNEL SELECTOR button again. • Then the channel levels memorized into the selected preset memory are recalled. POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET 34 P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A ENGLISH Memorizing the adjusted channel levels POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP LISTENING TO RADIO BROADCASTS ENTER SLEEP DIMMER DISPLAY RETURN TUNE 1 TUNE PRESET P.SCAN PRESET AUTO DSP STEREO SPK SET ADJUST PARAMATER 2 1 5 9 3 4 6 7 8 0 +10 2 3 4 6 7 8 MACRO M1 M2 M3 ENGLISH REMOTE CONTROL RNC-50A Auto tuning 1 2 Select the tuner. Select the desired band. BAND MHz INPUT SELECTOR POWER ON AUDIO AUD STANDBY CD VCR AUX DVD TV SAT SA CBL BAND DEVICE SELECT FREQUENCY CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP • Each time this button is pressed, the band is changed to FM or AM. • When pressing the BAND button without selecting the TUNER, the tuner will be selected automatically. ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE or TUNE PRESET TUNER P.SCAN DSP STEREO SPK SET ADJUST PARAMA ARAMATER TER TUNER CD 2 1 VIDEO 1 5 1 PRESET AUTO AUX 3 TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A 3 Select the auto tuning mode. POWER ON VCR T/P MODE 4 Press the TUNING/PRESET ▲/▼ buttons briefly or press the TUNE +/- buttons for more than 0.5 second. STANDBY CD AUX TV DVD SAT CBL CH.SEL T/V CH/LEVEL POWER ON MUTE AUD T.TONE STANDBY ANDBY CD AUX TV OSD VCR MENU DVD TUNING/PRESET SETUP ENTER SAT CBL DEVICE SELECT CH.SEL SLEEP T/V DIMMER CH/LEVEL DISPLAY VOLUME MUTE RETURN TUNE TUNE PRESET P.SCAN 2 1 PRESET 3 T.TONE .TONE OSD MENU SETUP ENTER AUTO DSP STEREO SPK SET ADJUST PARAMATER 2 1 5 3 4 6 7 8 0 +10 or 6 7 SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN DSP TUNER CD VIDEO 1 5 TUNE PARAMA ARAMATER TER AUX TAPE 3 4 2 1 M3 TUNE STEREO ADJUST SPK SET MACRO M2 PRESET 8 AUTO 9 M1 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 REMOTE CONTROL RNC-50A MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A • Each time this button is pressed, the mode changes as follows; Auto tuning mode • The tuner will now search until a station of sufficient strength has been found. The display shows the tuned frequency and “TUNED”. • If the station found is not the desired one, simply repeat this operation. • Weak stations are skipped during auto tuning. • When pressing the TUNE +/- buttons for more than 0.5 second on the remote control, you need not select the auto tuning mode on step ③. Manual tuning mode (“AUTO” lights up) (No indication) POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V Preset tuning mode(“PRESET” lights up) CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET 1 2 5 9 7 PARAMATER 3 4 6 7 8 0 +10 8 MACRO M1 M2 M3 POWER ON REMOTE CONTROL RNC-50A STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE PRESET T.TONE PRESET OSD MENU Manual tuning SETUP Presetting radio stations ENTER SLEEP DIMMER DISPLAY RETURN TUNE P.SCAN POWER ON VCR AUX TV SAT CBL T.TONE 4 7 8 0 +10 1 SETUP DIMMER RETURN TUNE P.SCAN M2 POWER ON M3 STANDBY Tune in the desired station with auto or manual tuning. CD VCR ENTER SLEEP PRESET 3 6 9 DVD AUX TV SAT CBL REMOTE CONTROL RNC-50A OSD MENU AUTO 2 5 MACRO MUTE DISPLAY PARAMATER 1 M1 T/V TUNE ADJUST SPK SET CH.SEL CH/LEVEL STEREO • You can store up to 30 preferred stations in the memory. STANDBY CD DVD PRESET DSP AUTO • Manual tuning is useful when you already know the frequency of the desired station. • Select the manual tuning mode performing the steps ① to ③ in “Auto tuning” procedure and press the TUNING/PRESET ▲/▼or TUNE +/- buttons repeatedly until the right frequency has been7 reached. • When pressing the TUNE +/- buttons repeatedly on the remote control, you need not select the manual tuning mode on step ③ in “Auto tuning” procedure. CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE PRESET TUNE PRESET P.SCAN PRESET STEREO AUTO PARAMATER SPK SET 1 2 3 4 1 2 3 4 5 6 7 8 5 6 7 8 9 0 +10 9 0 +10 DSP ADJUST SPK SET M2 DSP STEREO ADJUST 2 PARAMATER POWER ON MACRO M1 M1 M2 CD T/V MUTE T.TONE OSD MENU SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN POWER ON AUX 2 1 T/V6 5 0 DEVICE SELECT 4 7 8 +10 OSD MACRO M1 M2 SETUP M3 ENTER POWER ON TUNING/PRESET PARAMATER VOLUME MUTE 9 T.TONE MENU CBL CBL 3 CH.SEL CH/LEVEL TV SAT SA STEREO SAT SA ADJUST DEVICE SELECT STANDBY ST ANDBY AUX PRESET TV DSP DVD SPK SET CD PRESET STANDBY ST ANDBY CD AUTO VCR DVD CBL CH.SEL CH/LEVEL AUD POWER ON TV SAT DVD REMOTE CONTROL RNC-50A MEMO/ENTER VCR AUX M3 VCR 2 STANDBY Press the MEMORY/ENTER button. MACRO M3 REMOTE CONTROL RNC-50A AUD ENTER TUNE PRESET STANDBY CD VCR DVD AUX TV SAT CBL or SLEEPREMOTE CONTROL DIMMER RNC-50A DISPLAY DISPLA ENTER RETURN TUNE TUNE PRESET CH.SEL P.SCAN PRESET T/V CH/LEVEL VOLUME MUTE CH.SEL T/V T.TONE OSD MENU CH/LEVEL AUTO MUTE T.TONE TUNER SETUP 1 DIMMER TUNE P.SCAN DIMMER TUNE DISPLAY RETURN TUNE PRESET AUTO DSP STEREO SPK SET ADJUST PARAMA ARAMATER TER P.SCAN CD 2 VIDEO 1 5 AUX 3 AUX 3 7 0 +10 7 0 +10 2 4 8 MACRO M1 M2 M3 DSP STEREO TAPE 4 ADJUST SPK SET PARAMATER 8 MACRO M2 TAPE VIDEO 2 VIDEO 3 6 9 VIDEO 2 VIDEO 3 6 EXT. IN 9 PRESET TUNE REMOTE CONTROL RNC RNC-50A 50A AUTO 1 2 5 EXT. IN SLEEP PRESET TUNE M1 CD VIDEO 1 ENTER RETURN TUNE PRESET TUNER PARAMA ARAMATER TER OSD MENU SLEEP DISPLAY DISPLA STEREO ADJUST SPK SET SETUP ENTER or DSP 1 2 3 4 5 6 7 8 9 0 +10 6 7 8 • “MEM” is flickering for several seconds. M3 MACRO REMOTE CONTROL RNC-50A RNC 50A M1 M2 M3 REMOTE CONTROL RNC-50A 35 PRESET POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V POWER ON CH/LEVEL STANDBY MUTE CD T.TONE OSD MENU VCR DVD AUX TV SAT CBL SETUP ENTER CH.SEL T/V SLEEP DIMMER CH/LEVEL DISPLAY MUTE RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP ADJUST SPK SET T.TONE TUNE TUNE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN STEREO TUNE PARAMATER TUNE PRESET 1 2 3 4 5 6 7 8 9 0 +10 DSP ADJUST MACRO M1 M2 P.SCAN AUTO SPK SET 5 AUX TV SAT CBL 4 T.TONE ENGLISH POWER ON MENU CH/LEVEL SETUP DSP 5 9 6 7 8 0 +10 DIMMER RETURN PRESET TUNE PRESET STEREO 4 PRESET OSD SETUP ENTER SLEEP DISPLAY TUNE PARAMATER 3 CBL MUTE T.TONE TUNE PRESET ADJUST TV SAT MENU RETURN 2 AUX T/V DIMMER P.SCAN DVD CH.SEL ENTER SLEEP DISPLAY TUNE STANDBY CD OSD 1 REMOTE CONTROL RNC-50A VCR T/V AUTO 8 M3 MEMORY BACKUP FUNCTION MUTE SPK SET 7 +10 M2 The following items, set before the receiver is turned off, are memorized. • INPUT SELECTOR settings ENTER • Surround mode settings • Preset stations,etc. CH.SEL PRESET 0 MACRO M1 STANDBY CD DVD CH/LEVEL 6 Repeat the above steps ① to ③ to memorize other stations. 9 • The station has now been stored in the memory. • A stored frequency is erased from the memory by storing another frequencyPRESET in its PRESET place. ENTER • If “MEM” goes off, start again from the above step ②. POWER ON 4 MEMO/ENTER TUNING/PRESET VCR TUNE PARAMATER 3 M3 Select the desired preset number (1~30) and press the MEMORY/ENTER button. REMOTE CONTROL RNC-50A 3 TUNE STEREO 2 1 PRESET P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 MACRO M1 M2 M3 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A REMOTE CONTROL RNC-50A POWER ON STANDBY CD 1 2 After selecting the tuner as an input source, select the preset tuning mode. POWER ON AUX TV Select the desired preset number. MUTE VCR Tuning to preset stations DVD SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET STANDBY P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 POWER ON AUD CD AUX TV DVD SAT CBL TUNING/PRESET T/P MODE STANDBY CD VCR VCR AUX DVD TV SAT SA CBL MACRO DEVICE SELECT M1 M2 M3 CH.SEL T/V CH.SEL REMOTE CONTROL RNC-50A T/V CH/LEVEL CH/LEVEL VOLUME MUTE MUTE T.TONE .TONE T.TONE OSD OSD MENU MENU SETUP SETUP ENTER ENTER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET PRESET DIMMER SLEEP or DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN PRESET PRESET AUTO DSP AUTO DSP STEREO SPK SET ADJUST SPK SET ADJUST PARAMATER TUNER CD AUX TAPE 1 2 3 4 VIDEO 1 1 3 4 6 2 7 8 0 +10 5 PRESET PRESET STEREO PARAMA ARAMATER TER VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 5 9 9 POWER ON MACRO STANDBY M1 CD AUX M2 M3 TV MACRO M1 M2 M3 VCR DVD SAT CBL REMOTE CONTROL RNC-50A RNC 50A REMOTE CONTROL RNC-50A T.TONE CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP • When pressing the PRESET +/- buttons on the remote MENU control, you need not select the preset tuning mode on step ①. ENTER • Then “PRESET” lights up. DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A Listening to FM stereo broadcasts Scanning preset stations in sequence • While listening to FM broadcasts. FM MODE POWER ON AUD VCR STANDBY ANDBY CD AUX DVD SAT SA TV CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN DSP STEREO ADJUST PARAMA ARAMATER TER TUNER CD AUX 2 1 3 VIDEO 1 • Each time this button is pressed, the FM mode changes as follows; PRESET AUTO SPK SET 5 P.SCAN TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A Stereo mode : “ST” lights up. Mono mode : “ST” goes off. • The receiver will start scanning the stations in the preset sequence and each station is received for 5 seconds. • At the desired station, press this button again to stop scanning. • When FM stereo broadcasts are poor because of weak broadcast signals, select the FM mono mode to reduce the noise, then FM broadcasts are reproduced in monaural sound. POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE SLEEP OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET DISPLAY 36 P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A MENU SETUP ENTER DIMMER SLEEP DISPLAY RETURN TUNE 1 TUNE PRESET P.SCAN PRESET AUTO DSP STEREO SPK SET ADJUST PARAMATER 2 1 3 4 6 7 8 0 +10 POWER ON 5 9 STANDBY CD VCR AUX TV SAT CBL DVD 2 3 4 6 7 8 MACRO M1 M2 M3 CH.SEL T/V CH/LEVEL MUTE REMOTE CONTROL RNC-50A T.TONE OSD MENU SETUP ENTER RECORDING SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN 1 POWER ON STANDBY CD PRESET VCR DSP AUTO DVD AUX TV SAT CBL 2 3 4 6 7 8 STEREO CH.SEL ADJUST SPK SET PARAMATER T/V CH/LEVEL 2 1 3 4 7 8 MUTE T.TONE 5 6 OSD MENU SETUP • The analog signals from the EXTERNAL INs as well as the digital signals from the coaxial or optical digital input can be heard 2 3 4 1 but cannot be recorded. • The volume and tone (bass, treble) settings have no effect on the recording signals. 9 0 +10 ENTER SLEEP DIMMER DISPLAY RETURN MACRO M1 M2 M3 TUNE POWER ON TUNE STANDBY PRESET CD AUX REMOTE CONTROL RNC-50A VCR DVD SAT ENGLISH P.SCAN PRESET TV CBL CH.SEL AUTO DSP SPK SET ADJUST STEREO PARAMATER T/V POWER ON STANDBY CH/LEVEL MUTE CD AUX TV T.TONE VCR 1 2 3 4 5 6 7 8 0 +10 6 OSD DVD SAT CBL MENU 7 8 SETUP 9 ENTER CH.SEL SLEEP DIMMER T/V CH/LEVEL MACRO M1 MUTE DISPLAY M2 M3 RETURN TUNE TUNE T.TONE PRESET OSD PRESET P.SCAN MENU REMOTE CONTROL RNC-50A SETUP ENTER DSP AUTO STEREO DIMMER SLEEP ADJUST SPK SET DISPLAY PARAMATER RETURN TUNE Recording with1TAPE 1 TUNE 2 1 PRESET 3 P.SCAN 5 PRESET 6 7 0 +10 4 DSP ADJUST MACRO AUX TV SAT CBL 2 3 6 4 7 CH.SEL T/V 8 CH/LEVEL 7 8 2 MUTE Select the desired input as a recording source except for TAPE. 9 0 +10 T.TONE OSD MENU MACRO M1 1 6 M3 REMOTE CONTROL RNC-50A 5 4 PARAMATER M2 1 3 STANDBY CD DVD STEREO VCR M1 2 8 POWER ON 9 AUTO SPK SET M2 SETUP M3 ENTER SLEEP DIMMER DISPLAY RETURN Start recording on the TAPE. REMOTE CONTROL RNC-50A TUNE TUNE PRESET P.SCAN POWER ON VCR DSP AUTO STANDBY CD PRESET AUX DVD TV SAT CBL STEREO CH.SEL ADJUST SPK SET PARAMATER T/V CH/LEVEL 2 1 3 MUTE 4 T.TONE 5 6 7 0 +10 OSD 8 MENU 1 9 SETUP ENTER DIMMER SLEEP MACRO M1 M2 M3 DISPLAY RETURN TUNE POWER ON STANDBY ANDBY TUNE PRESET P.SCAN PRESET REMOTE CONTROL RNC-50A INPUT SELECTOR AUDIO AUD CD VCR VIDEO DVD AUX TV SAT SA CBL AUTO DSP SPK SET ADJUST STEREO 3 DEVICE SELECT PARAMATER CH.SEL POWER ON T/V CH/LEVEL VOLUME MUTE T.TONE VCR OSD MENU STANDBY CD AUX TV 1 2 3 4 DVD SAT CBL 5 6 7 8 0 +10 1 SETUP 9 TUNER ENTER CH.SEL T/V DIMMER SLEEP CH/LEVEL DISPLAY CD AUX 2 3 MACRO M1 MUTE M2 M3 RETURN TUNE TUNE PRESET P.SCAN 1 PRESET T.TONE OSD MENU SETUP Start play on the desired input. REMOTE CONTROL RNC-50A ENTER or DSP AUTO STEREO ADJUST SPK SET VIDEO 1 DIMMER SLEEP PARAMA ARAMATER TER DISPLAY CD AUX 2 1 3 VIDEO 1 TUNE TAPE PRESET 4 P.SCAN PRESET 6 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 VIDEO 2 VIDEO 3 RETURN TUNE TUNER 8 7 8 EXT. IN DSP AUTO POWER ON STANDBY ADJUST SPK SET CD AUX TV DVD SAT CBL MACRO M1 M2 STEREO PARAMATER M3 VCR REMOTE CONTROL RNC-50A RNC 1 5 1 CH.SEL 9 2 3 4 6 7 8 0 +10 T/V CH/LEVEL MUTE MACRO T.TONE M1 OSD MENU M2 M3 SETUP REMOTE CONTROL RNC-50A ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN POWER ON VCR DSP AUTO STANDBY 1 CD PRESET DVD AUX TV SAT CBL 2 3 STEREO Dubbing from video components onto 6 7 VIDEO 1 CH.SEL ADJUST SPK SET PARAMATER T/V CH/LEVEL 1 2 3 4 5 6 7 8 9 0 +10 2 3 2 6 7 8 MUTE T.TONE OSD MENU SETUP 8 ENTER POWER ON DIMMER SLEEP STANDBY MACRO CD AUX TV SAT CBL M1 M2 M3 DISPLAY RETURN TUNE VCR DVD TUNE PRESET P.SCAN 1 PRESET REMOTE CONTROL RNC-50A Start recording on the VIDEO 1. CH.SEL T/V DSP AUTO CH/LEVEL Select VIDEO 2 or VIDEO 3 as a recording source. ADJUST SPK SET T.TONE PARAMATER OSD POWER ON MENU 1 STEREO MUTE SETUP STANDBY CD AUX TV 1 2 3 4 SAT CBL 5 6 7 8 9 0 +10 ENTER VCR SLEEP DIMMER DISPLAY RETURN TUNE DVD TUNE CH.SEL PRESET P.SCAN T/V PRESET CH/LEVEL MACRO M1 MUTE T.TONE M2 M3 OSD REMOTE CONTROL RNC-50A DSP AUTO STEREO MENU ADJUST SPK SET SETUP 7 PARAMATER ENTER 1 2 3 4 5 6 7 8 0 +10 9 SLEEP DIMMER DISPLAY RETURN TUNE 8 TUNE PRESET P.SCAN 1 PRESET 2 3 6 7 MACRO M1 M2 POWER ON M3 STANDBY DSP AUTO INPUT SELECTOR AUD CD VCR TV ADJUST SPK SET REMOTE CONTROL RNC-50A VIDEO STEREO AUX DVD PARAMATER SAT SA CBL 2 SELECT 3 1 DEVICE 5 6 CH.SEL CH/LEVEL 9 0 MUTE 4 7 8 8 T/V VOLUME +10 T.TONE .TONE 3 Start play on the VIDEO 2 or the VIDEO 3. OSD MACRO M1 M2 MENU M3 SETUP ENTER REMOTE CONTROL RNC-50A DIMMER SLEEP or DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN POWER ON STANDBY CD PRESET DSP STEREO SPK SET ADJUST PARAMA ARAMATER AUX TV • The audio and video signals from the VIDEO 2 or the VIDEO 3 will be dubbed onto the VIDEO 1 and you can enjoy them on the TV set and from the speakers. VIDEO 2 VIDEO 3 VCR AUTO DVD SAT CBL CH.SEL CH/LEVEL TUNER CD AUX TAPE 3 4 2 1 VIDEO 1 5 7 0 +10 8 OSD 8 MENU EXT. IN 9 MUTE T.TONE VIDEO 2 VIDEO 3 6 7 T/V SETUP ENTER POWER ON STANDBY POWER ON DIMMER SLEEP CD AUX TV DVD SAT CBL STANDBY CD MACRO M1 VCR M2 M3 DISPLAY RETURN TUNE VCR TUNE PRESET P.SCAN DVD AUX TV SAT CBL PRESET REMOTE CONTROL RNC-50A RNC 50A CH.SEL CH.SEL T/V CH/LEVEL T/V CH/LEVEL MUTE DSP AUTO T.TONE OSD MENU MUTE STEREO ADJUST SPK SET POWER ON SETUP 7 PARAMATER STANDBY CD AUX TV 1 2 3 4 DVD SAT CBL 5 6 7 8 9 0 +10 8 T.TONE OSD MENU SETUP ENTER ENTER VCR SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN STEREO PARAMATER OSD SETUP M2 3 4 6 7 8 SLEEP DIMMER DISPLAY RETURN TUNE 0 9 2 TUNE PRESET P.SCAN PRESET M3 DSP AUTO POWER ON REMOTE CONTROL RNC-50A STEREO STANDBY ADJUST SPK SET VCR CD TV SAT 2 5 6 7 PARAMATER AUX DVD 1 0 8 CBL 3 4 7 8 PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 POWER ON STANDBY REMOTE CONTROL RNC-50A CD VCR Example) When dubbing the VIDEO 2 video signal and the CD audio signal separately onto VIDEO 1. CH.SEL 9 STEREO Select CD as 2an audio recording source. ADJUST SPK SET +10 M2 DSP AUTO 7 MACRO M1 PRESET M3 REMOTE CONTROL RNC-50A ENTER 2 5 TUNE P.SCAN MACRO M1 MUTE T.TONE MENU Dubbing the audio and video signals separately onto VIDEO 1 1 RETURN PRESET T/V CH/LEVEL DSP ADJUST DIMMER TUNE CH.SEL PRESET AUTO SPK SET SLEEP DISPLAY DVD T/V CH/LEVEL AUX TV SAT CBL CH.SEL +10 T/V CH/LEVEL MUTE MUTE MACRO T.TONE M1 M3 OSD M2 MENU T.TONE SETUP OSD MENU SETUP REMOTE CONTROL RNC-50A ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN POWER ON CD PRESET AUX AUTO DSP STEREO SPK SET ADJUST PARAMATER DVD SAT AUDIO 2 1 3 4 6 7 8 0 +10 7 T/V MUTE STANDBY 5 AUX TV SAT CBL 9 P.SCAN POWER ON PRESET AUD VCR DSP STEREO AUX SAT SA SPK SET ADJUST PARAMATER 2 2 T/V 3 4 6 7 8 0 +10 VOLUME MUTE T.TONE .TONE 5 SETUP OSD MENU 9 SETUP ENTER SLEEP DIMMER DISPLAY RETURN MACRO M1 TV CBL CH.SEL CH/LEVEL ENTER VCR STANDBY ANDBY CD DVD DEVICE SELECT AUTO OSD MENU CD DVD TUNE 1 T.TONE POWER ON RETURN PRESET CBL CH.SEL CH/LEVEL DIMMER INPUT SELECTOR TV Select VIDEO 2 as a video recording source. VCR 1 ENTER SLEEP DISPLAY TUNE STANDBY SLEEP DIMMER DISPLAY DISPLA RETURN MACRO M2 M3 TUNE M1 M2 M3 TUNE TUNE TUNE CH.SEL T/V CH/LEVEL PRESET PRESET PRESET AUTO DSP STEREO SPK SET ADJUST PARAMATER POWER ON 7 STANDBY ANDBY DIMMER SLEEP AUD DISPLAY CD AUX TV DVD SAT SA CBL 1 2 3 4 5 9 6 7 8 0 +10 STANDBY VCR PRESET DEVICE SELECT 2 VCR CD AUX TAPE AUX TV 1 2 3 4 DVD SAT CBL 5 6 7 9 0 +10 CH/LEVEL 8 CH.SEL T/V MACRO VOLUME MUTE M1 M2 CH/LEVEL M3 MACRO M1 MUTE M2 M3 PARAMATER T.TONE .TONE OSD T.TONE OSD REMOTE CONTROL RNC-50A 1 2 3 4 5 6 7 8 0 +10 9 VIDEO 2 VIDEO 3 EXT. IN T/V STEREO ADJUST STEREO PARAMA ARAMATER TUNER CD CH.SEL DSP AUTO SPK SET or DSP ADJUST VIDEO 1 TUNE P.SCAN VIDEO PRESET CD POWER ON AUTO SPK SET RETURN TUNE PRESET P.SCAN REMOTE CONTROL RNC-50A or OSD SETUP ENTER INPUT SELECTOR P.SCAN REMOTE CONTROL RNC-50A MUTE T.TONE MENU MENU SETUP ENTER 6 7 REMOTE CONTROL RNC-50A RNC 50A MENU 8 DIMMER SLEEP DISPLAY DISPLA DIMMER SLEEP RETURN TUNE SETUP ENTER DISPLAY TUNE RETURN TUNE TUNE MACRO M1 M2 M3 PRESET P.SCAN PRESET PRESET P.SCAN PRESET VIDEO 2 REMOTE CONTROL RNC-50A DSPSTANDBY STEREO AUTO POWER ON CD AUX VCR TUNER TV ADJUST SPK SET DVD CD SAT AUX 2 1 9 0 TAPE 4 7 T/V MACRO 8 M1 M2 2 3 4 5 6 7 8 0 +10 9 MACRO M3 MENU M1 M2 M3 SETUP ENTER REMOTE CONTROL RNC-50A RNC 50A REMOTE CONTROL RNC-50A DIMMER SLEEP RETURN TUNE P.SCAN POWER ON STANDBY CD PRESET VCR DSP AUTO AUX DVD SAT 2 TV CBL STEREO CH.SEL ADJUST SPK SET PARAMATER T/V CH/LEVEL 2 3 MUTE 4 6 T.TONE 6 7 0 +10 OSD 8 MENU 9 STEREO PARAMATER 1 OSD DISPLAY 5 ADJUST EXT. IN +10 TUNE PRESET SETUP 7 8 ENTER DIMMER SLEEP MACRO M1 SPK SET MUTE T.TONE 1 DSP VIDEO 2 VIDEO 3 6 CH.SEL CH/LEVEL 7 CBL 3 VIDEO 1 5 PARAMATER AUTO M2 M3 DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET REMOTE CONTROL RNC-50A DSP AUTO CD STEREO ADJUST SPK SET POWER ON PARAMATER STANDBY AUX TV 1 2 3 4 2 37 2 2 POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE OSD SETUP ENTER 3 SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET DSP AUTO ADJUST SPK SET 1 2 3 6 7 4 STEREO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 8 Start play on the VIDEO 2 and the CD respectively. MACRO M1 M2 M3 REMOTE CONTROL RNC-50A POWER ON STANDBY CD VCR • The audio signal from the CD and the video signal from the VIDEO 2 will be dubbed and you can enjoy them on the TV set and from the speakers. Note : Be sure to observe the order of the above steps ① and ②. DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET DIGITAL AUDIO RECORDING WITH MD RECORDER AUTO DSP SPK SET ADJUST STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 7 8 MACRO M1 M2 M3 • Only when the OPTICAL DIGITAL OUT of this receiver is connected to the OPTICAL DIGITAL IN of the MD recorder or CD recorder, you can enjoy high-quality sound of digital recording without converting the original signals. Refer to “CONNECTING VIDEO COMPONENTS”, “CONNECTING AUDIO COMPONENTS” and “CONNECTING DIGITAL INs and OUT” on pages 6~7 and the operating instructions of the MD recorder or CD recorder. Notes: • Digital recording is available for the digital audio program sources such as CDs, MDs, some DVDs, etc. • In most DVDs as well as some CDs, etc., digital recording may not be available depending on the signal format. • There are some restrictions on recording digital signals. When making digital recordings, refer to the operating instructions of your digital recording equipment to know what restrictions are imposed. REMOTE CONTROL RNC-50A POWER ON STANDBY CD VCR DVD AUX TV SAT CBL POWER ON DVD CH/LEVEL MUTE T.TONE OSD MENU 1 CBL MUTE T.TONE SETUP OSD MENU SETUP ENTER ENTER SLEEP DIMMER DISPLAY RETURN TUNE P.SCAN DSP STEREO ADJUST PARAMATER 2 3 6 7 9 0 +10 4 RETURN TUNE 2 M3 REMOTE CONTROL RNC-50A P.SCAN AUTO DSP SPK SET ADJUST 1 8 MACRO M2 DIMMER PRESET 7 Select a desired input of CD, VIDEO 1~3 as a recording source. 5 SLEEP DISPLAY TUNE PRESET AUTO SPK SET M1 TV SAT T/V TUNE 1 AUX CH.SEL T/V CH/LEVEL PRESET STANDBY CD VCR CH.SEL 2 PRESET STEREO PARAMATER 3 2 4 For digital recording, select the desired digital input as recording signal input. 5 6 7 9 0 +10 8 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A DIGITAL INPUTS POWER ON INPUT SELECTOR AUDIO AUD STANDBY CD VCR VIDEO AUX DVD TV SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP CD ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET or P.SCAN DSP STEREO ADJUST PARAMA ARAMATER TER AUTO SPK SET TUNER 1 PRESET CD 2 VIDEO 1 AUX 3 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 2 VIDEO 1 • Each time this button is pressed, the corresponding input is selected as follows: VIDEO 2 VIDEO 3 TAPE 8 6 7 8 EXT. IN A(nalog) o(ptical) 1 o(ptical) 2 c(oaxial) 2 c(oaxial) 1 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A Note : When the selected digital input is not connected, “DIGITAL” indicator flickers. There will be no recording as well as no sound. 3 Start recording on the component connected to OPTICAL DIGITAL OUT. 4 38 Start play on the desired input. ENGLISH T.TONE MENU Start recording on the VIDEO 1. AUTO POWER ON VCR AUX TV SAT CBL STEREO T/V MUTE ADJUST SPK SET MUTE CH.SEL CH/LEVEL DSP STANDBY CD DVD PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO T.TONE OSD M1 MENU M2 M3 SETUP REMOTE CONTROL RNC-50A ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET 2 1 9 PARAMATER 3 4 6 7 8 0 +10 OTHER FUNCTIONS 5 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A POWER ON STANDBY ENGLISH CD Compressing the dynamic range (Dolby Digital sources only) VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU • This function compresses the dynamic range of previously specified parts of the Dolby Digital sound T.TONE track(with extremely high volume) to minimize the difference inMENU volume between the specified and nonspecified parts. This makes it easy to hear all of the sound track when watching movies at night at low levels. • When the digital signals from Dolby Digital program source are input in available surround mode. POWER ON VCR DVD AUX TV ENTER SAT CBL T.TONE SLEEP DIMMER DISPLAY RETURN TUNE DYNR 0.0 : Off TUNE PRESET P.SCAN DSP ADJUST PRESET STEREO PARAMATER DSP STEREO ADJUST PARAMATER 3 4 6 2 7 8 0 +10 2 3 4 5 6 7 8 0 +10 9 M1 M2 M3 REMOTE CONTROL RNC-50A DYNR 0.5 : Low compression MACRO M2 1 MACRO PRESET AUTO SPK SET 9 TUNE P.SCAN AUTO SPK SET OSD SETUP ENTER 5 RETURN MUTE MENU 1 DIMMER TUNE T/V M1 SLEEP DISPLAY PRESET CH.SEL CH/LEVEL SETUP • Each time this button is pressed, the mode changes P.SCAN and the display scrolls. STANDBY CD DYNR 1.0 : High compression M3 REMOTE CONTROL RNC-50A • In some Dolby Digital softwares, this function may not be available. DYNAMIC RANGE POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE POWER ON SLEEP STANDBY CD AUX TV DVD SAT CBL OSD MENU SETUP ENTER VCR SLEEP DIMMER DISPLAY RETURN TUNE TUNE CH.SEL PRESET T/V CH/LEVEL P.SCAN PRESET MUTE T.TONE DISPLAY OSD MENU AUTO DSP SPK SET ADJUST STEREO SETUP PARAMATER ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET P.SCAN 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 AUTO DSP M3 STEREO ADJUST SPK SET M2 PARAMATER REMOTE CONTROL RNC-50A Operating the sleep timer 1 2 3 4 5 6 7 8 9 0 +10 Adjusting the brightness of the fluorescent displays MACRO M1 M2 M3 • The sleep timer allows the system to continue to operate for a specified period of time before automatically shutting off. • To set the receiver to automatically turn off after the specified period of time. REMOTE CONTROL RNC-50A POWER ON AUD VCR STANDBY ANDBY CD AUX DVD SAT SA TV CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP DIMMER ENTER POWER ON AUD SLEEP STANDBY ST ANDBY CD AUX TV DVD SAT SA CBL DIMMER DISPLAY DISPLA RETURN TUNE VCR TUNE PRESET P.SCAN PRESET DEVICE SELECT CH.SEL T/V CH/LEVEL AUTO DSP STEREO RETURN VOLUME MUTE ADJUST SPK SET T.TONE .TONE OSD MENU SETUP TUNER SLEEP 1 CD 2 VIDEO 1 5 ENTER PARAMA ARAMATER TER AUX TAPE 3 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN SLEEP 9 DIMMER DISPLAY DISPLA RETURN TUNE TUNE MACRO PRESET DISPLAY P.SCAN M1 PRESET M2 M3 REMOTE CONTROL RNC RNC-50A AUTO DSP STEREO ADJUST SPK SET TUNER CD VIDEO 1 5 PARAMA ARAMATER TER AUX TAPE 3 4 2 1 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC • Each time this button is pressed, the brightness of all fluorescent displays of Sherwood components connected by the DIGI LINK III changes together as follows; • Each time this button is pressed, the sleep time changes as follows: → 10 → 20 → 30 → --- → 90 → OFF → ON → dimmer → OFF Unit : minutes POWER ON STANDBY CD AUX TV SAT CBL • While operating the sleep timer, “ ” lights up. • When the sleep time is selected, all display panels DIMMER of Sherwood components connected by the DIGI LINK III are dimly lit. RETURN DVD VCR • In the display OFF mode, pressing any button will restore the display ON mode. CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET DSP AUTO STEREO ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A 39 This unit incorporates an OSD(On-screen display) function to provide information about basic operation of this unit and to simplify the setup procedures. The OSD function uses a monitor TV connected to this unit as a display and has two kinds of display modes such as current status display and menu screen. ■Notes: • Any on-screen display shown on the monitor TV will not be recorded. • Because this unit cannot support the OSD function for the progressively scanned video signal, the OSD for current status and menu settings may be displayed abnormally or may not be displayed. CURRENT STATUS DISPLAY This mode shows the status corresponding to each operation. • The on-screen display will automatically disappear in several seconds. • For examples, there are 2 status displays as follows. Notes • When watching a movie earnestly, if you want to turn off the current status display function, set the OSD auto display mode to Off(For details, refer to “When selecting the AUTO OSD” on page 41) ※Current status display function might not operate as expected if : • You view a movie via MONITOR COMPONENT OUTs while component video signals are input into this receiver. • You view a movie via MONITOR COMPOSITE OUT while S-Video signals and composite video signals are input into this receiver. When selecting the desired input source When selecting the TEST TONE mode V I DEO 1 ( OP T I CA L 1 ) FL C FR SW SL FL Input source Signal input ------- SB SR ---- --- Channel level or master volume display 0 • When adjusting overall volume, the volume level display will be shown. • The test tone display will be shown until the test tone mode is canceled. OSD Menu Settings • The OSD menu allows you to perform the setup procedures easily. In most situations, you will only need to set this once during the installation and layout of your home theater, and it rarely needs to be changed later. The OSD menu consists of 5 main menus : speaker setup, function select, surround mode, CH level setup and auto OSD. Some of these menus are divided into sub-menus. • The OSD menu settings are performed easily with the CURSOR control(▲, ▼, ◀, ▶), OSD and ENTER buttons. ■Notes : • In such a case of making only COMPONENT VIDEO connections between this receiver and video component, while viewing a movie via the MONITOR COMPONENT OUTs, if the OSD menu operation is performed, the picture is automatically turned off and only the OSD menu is displayed. • When S-Video signals and composite video signals are input into this receiver, even though the OSD menu operation is performed, the OSD menu cannot be displayed via MONITOR COMPOSITE OUT. 1 Turn the menu screen on. POWER ON MA I N MENU S P E A K E R S E T UP F UNC T I ON S E L E C T SURROUND MODE CH L E V E L S E T U P AU TO OSD : ON STANDBY AUD CD AUX TV VCR DVD SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL MUTE VOLUME PTY SELECT SETUP T.TONE .TONE OSD OSD MENU RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN DSP STEREO ADJUST PARAMA ARAMATER TER TUNER CD AUX TAPE 3 4 2 1 VIDEO 1 5 : MOV E O S D : E ND SETUP PRESET AUTO SPK SET EN T ER : SEL . VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 • In the bottom of the display, “OSD” stands for the OSD button. “ENTER” for “ENTER”, “▲”, “▼”, “◀”, and “▶” for CURSOR UP(▲), DOWN(▼), LEFT(◀) and RIGHT(▶). MACRO M1 M2 M3 REMOTE CONTROL RNC-55A RNC 55A • The main menu will be shown. • To turn the menu screen off, press this button again. POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE MENU OSD PTY SELECT RDS ENTER SETUP 40 ENGLISH Using the OSD DISPLAY ENTER SETUP RETURN TUNE TUNE DIMMER SLEEP PRESET P.SCAN DISPLAY PRESET RETURN TUNE TUNE PRESET P.SCAN PRESET AUTO DSP SPK SET ADJUST STEREO PARAMATER DSP AUTO STEREO 2 1 3 ADJUST SPK SET 5 7 8 3 9 4 0 5 4 PARAMATER 6 2 1 +10 6 7 8 0 MACRO+10 9 M1 M2 M3 MACRO REMOTE CONTROL RNC-55A M2 M3 M1 REMOTE CONTROL RNC-50A 2 Select the desired menu using the CURSOR UP(▲)/DOWN(▼) buttons. POWER ON STANDBY CD AUX POWER ON AUD TV STANDBY ANDBY CD VCR AUX DVD TV SAT VCR CBL DVD SAT SA CBL DEVICE SELECT CH.SEL T/V CH.SEL MUTE CH/LEVEL T/V CH/LEVEL VOLUME MUTE T.TONE OSD T.TONE .TONE MENU OSD SETUP ENGLISH MENU ENTER PTY SELECT SETUP RDS ENTERDIMMER SLEEP SEARCH MODE DIMMER SLEEP DISPLAY RETURN TUNE TUNE DISPLAY DISPLA TUNE PRESET RETURN TUNE PRESET P.SCAN PRESET P.SCAN PRESET DSP AUTO STEREO DSP ADJUST AUTO SPK SET 2 4 CD 1 3 7 VIDEO 1 6 0 TAPE AUX 2 6 5 9 PARAMATER 3 TUNER 5 STEREO PARAMATER ADJUST SPK SET 1 4 8 VIDEO 2 VIDEO 3 7 +10 8 EXT. IN 9 0 +10 MACRO M1 M2 M3 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A REMOTE CONTROL RNC-55A RNC 55A 3 Confirm your selection. POWER ON STANDBY CD VCR AUX DVD TV SAT POWER ON CBL STANDBY ANDBY AUD CD VCR DVD AUX TV CH.SEL SAT SA CBL T/V CH/LEVEL MUTE DEVICE SELECT T.TONE OSD CH.SEL T/V CH/LEVEL MENU PTY SELECT VOLUME SETUP MUTE RDS ENTER T.TONE .TONE OSD SEARCH MODE DIMMER SLEEP MENU SETUP DISPLAY RETURN TUNE TUNE ENTER PRESET SLEEP P.SCAN ENTER PRESET DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET AUTO P.SCAN DSP PRESET STEREO ADJUST SPK SET PARAMATER DSP AUTO STEREO 2 1 3 4 ADJUST SPK SET 5 6 TUNER 8 TAPE AUX 0 2 +10 3 VIDEO 1 5 PARAMATER 7 CD 9 1 4 VIDEO 2 VIDEO 3 6 7 8 MACRO M1 EXT. IN M2 9 M3 0 +10 REMOTE CONTROL RNC-55A MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A ■When selecting the SPEAKER SETUP ■When selecting the FUNCTION SELECT S PE A K ER S E T UP POWER ON STANDBY F UNC T I ON SE L E C T POWER ON CD AUX STANDBY CD AUX VCR VCR TV TV DVD DVD SAT SAT CBL CBL CH.SEL A U TO MA NUA L T/V CH.SEL CH/LEVEL D I G I T A L I NP U T V I DEO S E L E C T T ONE CON T ROL MUTE T/V CH/LEVEL MUTE T.TONE OSD T.TONE OSD PTY SELECT MENU MENU SETUP SETUP RDS ENTER ENTER SEARCH MODE DIMMER SLEEP DIMMER SLEEP 42 DISPLAY RETURN TUNE TUNE DISPLAY TUNE RETURN TUNE P.SCAN PRESET PRESET P.SCAN DSP AUTO AUTO DSP SPK SET 1 1 : MOV E O S D : BA CK 5 : MOV E O S D : B A CK EN T ER : SEL . 9 2 5 6 9 0 45 STEREO STEREO ADJUST PARAMATER ADJUST SPK SET RDS ENTER PRESET PRESET 2 PARAMATER 3 4 3 6 4 7 8 7 0 +10 8 +10 MACRO M1 M2 M3 MACRO M1 M2 M3 REMOTE CONTROL RNC-55A EN T ER : SEL . REMOTE CONTROL RNC-50A ■When selecting the SURROUND MODE ■When selecting the CH LEVEL SETUP CH L E V E L TR I M REF . 1 ------FL ------------------C FR - - - - - - ------------SR - - - - - - - S URROUND MOD E DO L B Y D I G I T A L E X DO L B Y D V S R E F DO L B Y D V S W I D E 2 CH DOWNM I X O S D : B A CK 47 : MOV E O S D : B A CK : SE L EC T 0 0 0 0 48 : C H A NGE E N T E R : MEMO • For the setting details, see page in . • Adjust the setting(s) in each setting category to your preference. • When the OSD button is pressed on a sub-menu, the previous menu is resumed. ■When selecting the AUTO OSD • Each time the ENTER button is pressed, the AUTO OSD mode is set to ON to turn on the current display or OFF to turn it off. • When the AUTO OSD mode is set to ON, the current status display overlays the program image on the monitor TV and may interference with your movie enjoyment. In such a case, set it to OFF. 41 • After you have installed this receiver and connected all the components, you should adjust the speaker settings for the optimum sound acoustics according to your environment and speaker layout. • Even when you change speakers, speaker positions, or the layout of your listening environment, you should adjust the speaker settings, too. S PE A K ER S E T UP To set the speaker setup automatically(Auto Speaker Setup) To set the speaker setup manually(Manual Speaker Setup) A U TO MA NUA L : MOV E O S D : BA CK Note: • Because the microphone for Auto Speaker Setup is designed for use with this receiver, to use the auto speaker setup function, do not use a microphone other than the one supplied with this receiver. EN T ER : SEL . When selecting the AUTO SPEAKER SETUP • Auto Speaker Setup lets you avoid troublesome listening-based speaker setup and achieve good surround sound. You should connect the supplied microphone to the SETUP MIC jack so that this receiver can analyze the information from a series of test tones emitted from speakers and can adjust the size, distance and sound level of each speaker automatically. ENTER • If you want to personalize your speaker setup and channel level setup by making the settings manually, perform the “When selecting the MANUAL SPEAKER SETUP” procedure on page 43, “Adjusting each channel level with test tone” procedure on page 32 and “Adjusting the current channel level”on page 33. POWER ON STANDBY CD VCR DVD TV SAT CBL DVD CH/LEVEL MUTE PRESET AUTO 1 5 OSD T.TONE SETUP OSD MENU SETUP ENTER DIMMER RETURN TUNE P.SCAN DIMMER RETURN PRESET TUNE PRESET P.SCAN PRESET STEREO AUTO PARAMATER SPK SET 3 4 1 2 3 4 6 7 8 5 6 7 8 0 +10 9 0 +10 M3 M1 DSP 9 SLEEP DISPLAY TUNE 2 ADJUST MACRO M1 CBL MUTE ENTER SPK SET TV SAT T/V T.TONE SLEEP AUX CH.SEL DISPLAY TUNE STANDBY CD VCR T/V CH/LEVEL MENU POWER ON AUX CH.SEL M2 DSP STEREO ADJUST PARAMATER MACRO Preparations REMOTE CONTROL RNC-50A 2. Place the microphone on a flat level surface at your normal listening position. • If possible, use a tripod, etc. to attach the microphone at the same height as your ears would be when you are seated in your listening position. • Ensure there are no obstacles between the speakers and the microphone. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the AUTO SPEAKER SETUP, then press the ENTER button. POWER ON AUD 2 STANDBY CD VCR AUX DVD M3 REMOTE CONTROL RNC-50A 1. Connect the supplied microphone to the SETUP MIC jack on the rear panel,(For details, refer to “CONNECTING MICROPHONE” on page 10) 1 M2 Press the CURSOR UP(▲)/DOWN(▼)/ LEFT(◀)/RIGHT(▶) buttons to specify the setting condition according to the number of speakers installed and speakers’ frequency characteristics. POWER ON TV SAT SA STANDBY CD VCR CBL DVD AUX TV SAT CBL DEVICE SELECT CH.SEL CH.SEL T/V CH/LEVEL T/V T.TONE .TONE OSD MENU POWER ON CH/LEVEL VOLUME MUTE SETUP T.TONE POWER ON STANDBY CD AUX TV DVD SAT CBL STANDBY CD AUX TV DVD SAT CBL SLEEP DIMMER DISPLAY DISPLA RETURN TUNE OSD MENU ENTER ENTER VCR VCR MUTE SETUP POWER ON AUD VCR SLEEP DIMMER DISPLAY RETURN TUNE DVD P.SCAN PRESET T/V CH/LEVEL P.SCAN PRESET CH/LEVEL MUTE T.TONE AUTO OSD DSP OSD ENTER 1 CD 2 VIDEO 1 AUX TAPE 3 4 5 6 7 9 0 +10 P.SCAN DIMMER RETURN VOLUME MUTE SETUP PARAMATER ENTER 1 8 TUNE TUNE PRESET P.SCAN PRESET 2 3 5 6 7 9 0 +10 MACRO M2 4 SLEEP 8 DISPLAY DISPLA DIMMER RETURN TUNE TUNE PRESET P.SCAN PRESET MACRO M3 M1 AUTO DSP DSP M2 M3 AUTO STEREO DSP STEREO STEREO ADJUST SPK SET ADJUST PARAMATER 2 3 4 5 6 7 8 0 +10 PARAMA ARAMATER TER REMOTE CONTROL RNC-50A 1 2 3 4 1 5 6 7 8 5 0 +10 9 M3 M1 CD 2 VIDEO 1 AUX 3 TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO MACRO ADJUST SPK SET PARAMATER REMOTE CONTROL RNC RNC-50A 50A TUNER 1 M2 OSD STEREO ADJUST SPK SET PRESET M1 AUTO SPK SET DSP MENU ENTER EXT. IN TUNE PRESET SLEEP DISPLAY VIDEO 2 VIDEO 3 RETURN TUNE SETUP PARAMA ARAMATER TER ENTER TUNER DIMMER DISPLAY ADJUST SPK SET T.TONE .TONE AUTO STEREO MENU SETUP ENTER SLEEP 9 CBL T/V MUTE T.TONE MENU M1 TV SAT SA CH.SEL PRESET T/V CH/LEVEL AUX DEVICE SELECT TUNE CH.SEL PRESET CH.SEL STANDBY ST CD ENTER TUNE M1 M2 MACRO M2 M3 M3 REMOTE CONTROL RNC-50A REMOTE CONTROL RNC-50A RNC 50A REMOTE CONTROL RNC-50A A U T O SE T UP • To specify the layout of the installed speakers, press the CURSOR UP(▲) or DOWN(▼) button. • To specify the crossover frequency, press the CURSOR LEFT(◀) button. You can specify the crossover frequency with the range of 40~130 Hz in 10 Hz intervals. • To specify the subwoofer, press the CURSOR RIGHT(▶) button. A L L C H A NNE L F L - C - F R - SR - S L F L - F R - SR - S L F L - C - FR F L - FR : CU TOF F : SW Yes POWER ON 42 STANDBY CD VCR 8 0 H z Enter : S T AR T : MOV E OSD : B AC K DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER ENTER ENGLISH SETTING THE SPEAKER SETUP ENGLISH 3 Press the ENTER button to start the auto speaker setup procedure. Example) When analyzing the test tones POWER ON POWER ON AUD AUX TV SAT SA CBL A U T O S E T UP STANDBY CD STANDBY CD DVD VCR VCR AUX TV SAT CBL DVD DEVICE SELECT T/V CH.SEL CH/LEVEL T/V MUTE VOLUME MUTE T.TONE T.TONE .TONE FL OSD OSD MENU MENU SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE SETUP ENTER PRESET P.SCAN PRESET DSP AUTO ADJUST DIMMER DISPLAY RETURN TUNE SETUP TUNE AUTO SPK SET CD AUX TAPE 1 2 3 4 VIDEO 1 5 PRESET STEREO PARAMA ARAMATER TER TUNER C FR ENTER SLEEP TUNE SPK SET FL+ FR+ C SL+ S R+ SB+ SW OSD CH.SEL CH/LEVEL Example) Result report P.SCAN PRESET DSP SW STEREO ADJUST 2 1 SL PARAMATER 3 4 SB SR VIDEO 2 VIDEO 3 6 7 0 +10 8 5 6 7 9 POWER +10 ON 0 STANDBY CD AUX TV DVD SAT CBL POWER ON Enter : S T OP MACRO M2 MACROVCR M3 M1 M2 M3 10 f 10 f 10 f 7f 8f 7f t t t t t t L A RGE L A RGE SMA L L SMA L L SMA L L SMA L L : TES T L EVE L SMA L L : EX I T : R E T R Y Enter : SE T UP 8 EXT. IN 9 M1 0 0 dB 0 0 dB - 1 5dB - 0 4 dB + 0 2 dB - 0 5 dB - 1 5 dB STANDBY CD VCR DVD AUX TV SAT CBL REMOTE CONTROL RNC-50A RNC REMOTE CONTROL RNC-50A CH.SEL CH.SEL T/V CH/LEVEL T/V CH/LEVEL MUTE T.TONE OSD MENU T.TONE SETUP DIMMER RETURN TUNE PRESET P.SCAN OSD MENU ENTER ENTER SLEEP DISPLAY MUTE SETUP Polarity Channel level Speaker distance ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET PRESET Speaker size TUNE P.SCAN PRESET • Loud test tones are output from each speaker and then if the auto speaker setup procedure has been completed, the results of each adjustment will be displayed. • To stop the auto speaker setup procedure while outputting the test tones, press the ENTER button. • If the polarity is incorrect, “-” will be displayed. • If there may be a problem with the speaker or microphone connection, “▶▶ ERROR ◀◀” message will be displayed. • When “▶▶ ERROR ◀◀” message is displayed, press the CURSOR RIGHT(▶) button to retry the auto speaker setup procedure. • If retrying the procedure dose not fix the problem, turn off the power and check the speaker or microphone connections. ■Notes : • For details on speaker size, crossover frequency and speaker distance, refer to “About the speaker size” and “About the speaker distance” on page 19. • Because the test tones are very loud, ensure there no infants or small children in the room. • It is possible to lower the volume of the test tomes, but this could result in incorrect speaker settings. • For best results, ensure the room is as quiet as possible during the auto speaker setup procedure. If there is too much ambient noise, the results may not be satisfactory. • If the results are not satisfactory, set the speaker setup manually. (For details, refer to “When selecting the MANUAL SPEAKER SETUP” on page 43) AUTO STEREO AUTO PARAMATER SPK SET 1 2 3 4 1 2 3 4 5 6 7 8 5 6 7 8 9 0 +10 9 0 +10 M3 M1 DSP ADJUST SPK SET POWER ON STEREO PARAMATER STANDBY AUXMACROTV CD M1 VCR DSP ADJUST MACRO M2 DVD SAT M2 M3 CBL REMOTE CONTROL RNC-50A REMOTE CONTROL RNC-50A CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER ENTER DIMMER SLEEP DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET POWER ON DSP AUTO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 STANDBY CD STEREO ADJUST SPK SET VCR AUX TV SAT CBL DVD CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MACRO M1 M2 MENU M3 SETUP ENTER REMOTE CONTROL RNC-50A SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A Confirm the results. POWER ON STANDBY CD VCR 4 AUX TV SAT CBL DVD CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN POWER ON TUNE AUD CD VCR DVD STANDBY AUX ENTER TUNE TV PRESET P.SCAN SAT SA PRESET CBL DEVICE SELECT AUTO DSP STEREO CH.SEL ADJUST T/V SPK SET CH/LEVEL PARAMATER VOLUME MUTE 1 2 5 6 9 0 T.TONE .TONE 3 4 7 8 OSD MENU SETUP ENTER +10 SLEEP ENTER DIMMER MACRO DISPLAY DISPLA M2 RETURN M3 M1 TUNE TUNE PRESET P.SCAN PRESET REMOTE CONTROL RNC-50A AUTO DSP STEREO SPK SET ADJUST PARAMA ARAMATER TER TUNER CD 3 VIDEO 1 • Then the results are memorized. TAPE AUX 2 1 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A When selecting the MANUAL SPEAKER SETUP POWER ON STANDBY CD VCR AUX TV SAT CBL DVD Press the CURSOR UP(▲)/DOWN(▼) buttons to select the MANUAL SPEAKER SETUP, then press the ENTER button. CH.SEL T/V CH/LEVEL 1 MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST 1 2 5 6 9 0 PRESET STEREO VCR M A NU A L S E TUP PARAMATER 3 POWER ON AUD CD 7 +10 4 STANDBY 8 DVD AUX TV SAT SA CBL S U BWOOF E R F RON T CE N T ER SURR SURR B - DEVICE SELECT MACRO M1 M2 CH.SEL M3 T/V CH/LEVEL VOLUME MUTE REMOTE CONTROL RNC-50A T.TONE .TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST TUNER 1 CD 2 VIDEO 1 5 ENTER PRESET STEREO 3 7 0 +10 TAPE 4 : MOV E O S D : B A CK 8 MACRO M2 YE S L ARGE L ARGE L ARGE L ARGE PARAMA ARAMATER TER AUX VIDEO 2 VIDEO 3 6 EXT. IN 9 M1 - M3 REMOTE CONTROL RNC-50A RNC 50A 43 : CH ANGE CD VCR AUX TV SAT CBL DVD OSD CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU PTY SELECT SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY TUNE P.SCAN PRESET DSP STEREO ADJUST PARAMATER 2 1 5 9 POWER ON SETUP RETURN TUNE PRESET AUTO SPK SET 3 4 6 7 8 0 +10 STANDBY MACRO VCR CD AUX TV DVD SAT CBL M1 M2 M3 REMOTE CONTROL RNC-55A OSD CH.SEL T/V CH/LEVEL MUTE Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired item. T.TONE OSD MENU SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY SETUP RETURN TUNE TUNE PRESET P.SCAN PRESET AUTO DSP STEREO SPK SET ADJUST PARAMATER 2 1 5 3 4 6 7 8 0 +10 POWER ON 9 AUD STANDBY CD VCR ENGLISH 2 PTY SELECT AUX DVD TV SAT SA CBL MACRO M1 M2 M3 DEVICE SELECT CH.SEL REMOTE CONTROL RNC-55A T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU PTY SELECT SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET PARAMA ARAMATER TER TUNER CD AUX 1 2 3 VIDEO 1 5 TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 POWER ON STANDBY MACRO VCR CD AUX TV DVD SAT CBL M1 M2 M3 REMOTE CONTROL RNC RNC-55A 55A CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU PTY SELECT SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY RETURN TUNE TUNE PRESET 3 P.SCAN PRESET Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to set the selected item as desired. AUTO DSP SPK SET ADJUST STEREO PARAMATER POWER ON 1 2 3 4 5 6 7 8 9 0 +10 STANDBY CD VCR AUX TV SAT CBL DVD CH.SEL T/V MACRO M1 M2 CH/LEVEL M3 ■In case of speaker size, you can select one of these following types. MUTE T.TONE OSD REMOTE CONTROL RNC-55A MENU PTY SELECT SETUP RDS ENTER SLEEP YES/NONE: Select the desired depending on whether a subwoofer is connected or not. LARGE: Select this when connecting speakers that can fully reproduce sounds below crossover frequency. SMALL: Select this when connecting speakers that can notOSD fully reproduce sounds below crossover frequency. When this is selected, sounds below crossover SETUP frequency are sent to the subwoofer or speakers which are set to LARGE(when not using a subwoofer) NONE: Select this when no speakers are connected. When this is selected, sounds are sent to the speakers which are not set to NONE. SEARCH MODE DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET AUTO DSP STEREO SPK SET ADJUST PARAMATER 2 1 3 4 6 7 8 0 +10 POWER ON 5 9 POWER ON MACRO CD AUX TV VCR DVD SAT SA CBL M1 M2 STANDBY CD VCR STANDBY AUD M3 AUX TV SAT CBL DVD CH.SEL T/V CH/LEVEL REMOTE CONTROL RNC-55A DEVICE SELECT T.TONE CH.SEL MUTE VOLUME PTY SELECT SETUP T.TONE .TONE RETURN TUNE P.SCAN PRESET AUTO DSP STEREO SPK SET ADJUST PARAMA ARAMATER TER CD 3 VIDEO 1 5 TAPE AUX 2 1 DIMMER RETURN TUNE PRESET SEARCH MODE DIMMER TUNER SLEEP DISPLAY TUNE RDS ENTER SLEEP DISPLAY DISPLA TUNE PRESET 4 7 P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 VIDEO 2 VIDEO 3 6 SETUP ENTER OSD MENU OSD MENU T/V CH/LEVEL MUTE MACRO 8 M1 M2 M3 EXT. IN 9 0 +10 POWER ON STANDBY REMOTE CONTROL RNC-50A CD AUX TV SAT CBL MACRO M1 M2 VCR M3 DVD REMOTE CONTROL RNC RNC-55A 55A CH.SEL T/V CH/LEVEL MUTE T.TONE MENU OSD PTY SELECT SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET PARAMATER RDS ENTER • Crossover frequency is the frequency(Hz) below which the bass sound of each main speakers is to output from the subwoofer or from speakers which are set to LARGE(when not using a subwoofer). • Refer to the operating instructions of the speakers to be connected. If the frequency range of your speaker is 100Hz~20kHz, the crossover frequency have to be set to 100Hz(or slightly higher) POWER ON 1 2 3 4 5 6 7 8 9 0 +10 STANDBY CD VCR POWER ON STANDBY AUX TV M1 M2 M3 DVD SAT TV SAT CBL T/V CH/LEVEL VCR AUX DVD CH.SEL MACRO CD CBL REMOTE CONTROL RNC-55A MUTE T.TONE OSD MENU SETUP CH.SEL T/V CH/LEVEL ENTER ■In case of speaker distance, you can adjust the distance between the MUTE T.TONE OSD SLEEP DIMMER DISPLAY RETURN TUNE MENU PTY SELECT SETUP TUNE PRESET RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET AUTO DSP STEREO SPK SET ADJUST PARAMATER 1 2 3 4 5 6 7 8 0 +10 RDS ENTER P.SCAN AUTO DSP SPK SET ADJUST 9 MACRO M2 M3 STEREO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 ■In case of crossover frequency, you can adjust the crossover frequency MACRO M1 M1 PRESET listening position and each speaker within the range of 1~30 feet in 1 foot intervals. M2 M3 REMOTE CONTROL RNC-50A within the range of 40~130Hz in 10Hz intervals. REMOTE CONTROL RNC-55A ■Notes : • When speakers are set to “SMALL”, you should set the CROSSOVER FREQUENCY correctly according to their frequency characteristics. • When “SUBWOOFER” is set to “NONE”, “FRONT” is automatically set to “LARGE”. • When the “FRONT” is set to “SMALL”, “CENTER”, ”SURR” , ”SURR B” cannot be set to “LARGE”. • When the “SURR” is set to “SMALL”, “SURR B” cannot be set to “LARGE”. • You cannot adjust the distances of subwoofer and the speakers set to “NONE”. POWER ON STANDBY CD VCR AUX TV SAT CBL DVD CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST PRESET STEREO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A 4 Repeat the above steps ② and ③ until the items are all set to the desired. 5 Confirm your selection. POWER ON AUD STANDBY ANDBY CD VCR DVD AUX TV SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY DISPLA ENTER RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET TUNER CD PARAMA ARAMATER TER TAPE AUX 2 1 3 VIDEO 1 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A • The adjusted settings are memorized. POWER ON STANDBY CD VCR 44 DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE PRESET TUNE P.SCAN PRESET SELECTING THE FUNCTION ENGLISH F UNC T I ON SE L E C T To select a digital input To select a video input source To adjust the tone as desired. D I G I T A L I NP U T V I DEO S E L E C T T ONE CON T ROL : MOV E O S D : B A CK EN T ER : SEL . When selecting the DIGITAL INPUT POWER ON AUX DVD SAT CH.SEL T/V CH/LEVEL Note: When TUNER, TAPE, AUX or EXTERNAL IN is selected as an input source, the DIGITAL INPUT cannot be selected. STANDBY CD VCR TV CBL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN TUNE 1 TUNE PRESET P.SCAN PRESET DSP AUTO STEREO ADJUST SPK SET PARAMATER 1 2 3 5 6 7 0 +10 9 ENTER Press the CURSOR UP(▲)/DOWN(▼) buttons to select the DIGITAL INPUT, then press the ENTER button. 4 8 MACRO M1 M2 M3 D I G I TA L REMOTE CONTROL RNC-50A POWER ON AUD VCR STANDBY CD AUX TV DVD SAT SA CBL CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER ENTER SLEEP DIMMER DISPLAYON DISPLA POWER RETURN STANDBY TUNE TUNE CD AUX PRESET VCR TV P.SCAN DVD PRESET SAT AUTO CBL DSP STEREO OSD CH.SEL T/V ADJUST SPK SET CH/LEVEL PARAMA ARAMATER TER MUTE TUNER CD TAPE AUX 2 1 T.TONE 3 VIDEO 1 5 MENU I N PU T A NA LOG OP T I C A L 1 OP T I C A L 2 CO A X I A L 1 CO A X I A L 2 DEVICE SELECT 4 OSD VIDEO 2 VIDEO 3 6 SELECT PTY 7 8 SETUP EXT. IN 0RDS +10 ENTER 9 SLEEP SEARCH MODE DIMMER RETURN M3 M2 TUNE STANDBY CD AUX TV SAT CBL PRESET P.SCAN O S D : B A CK SETUP MACRO DISPLAY M1 TUNE POWER ON PRESET : SE L EC T REMOTE CONTROL RNC RNC-50A 50A VCR DVD CH.SEL AUTO DSP STEREO SPK SET ADJUST PARAMATER T/V CH/LEVEL MUTE 2 1 T.TONE OSD MENU SETUP 5 9 3 4 6 7 8 0 +10 ENTER ENTER MACRO SLEEP DIMMER DISPLAY RETURN TUNE M1 M2 M3 TUNE REMOTE CONTROL RNC-55A PRESET P.SCAN PRESET DSP AUTO STEREO ADJUST SPK SET PARAMATER 1 2 3 5 6 7 9 0 +10 MACRO M1 M2 M3 2 Press the CURSOR UP(▲)/DOWN(▼) buttons to select the digital or analog input as desired. 4 8 POWER ON STANDBY REMOTE CONTROL RNC-50A CD VCR AUX DVD POWER ON AUD CBL T/V AUX CD CH/LEVEL VCR TV SAT STANDBY CH.SEL TV MUTE DVD SAT SA CBL T.TONE OSD DEVICE SELECT MENU SETUP ENTER CH.SEL ENTER T/V CH/LEVEL SLEEP VOLUME DIMMER MUTE T.TONE .TONE DISPLAY OSD RETURN TUNE TUNE MENU PTY SELECT PRESET P.SCAN • The sound from the component connected to the selected digital input can be heard regardless of the selected input source. SETUP PRESET RDS ENTER SLEEP SEARCH MODE DIMMER AUTO DSP STEREO DISPLAY DISPLA RETURN TUNE TUNE ADJUST SPK SET PRESET PARAMATER P.SCAN PRESET 1 2 3 5 6 7 AUTO 4 8 DSP 9 STEREO 0 +10 ADJUST SPK SET TUNER CD 2 M1 M2 TAPE 3 4 M3 VIDEO 1 5 PARAMA ARAMATER TER AUX MACRO 1 VIDEO 2 VIDEO 3 6 7 8 EXT. IN RNC-50A 9REMOTE 0 CONTROL +10 MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-55A 55A POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET POWER ON STANDBY CD DSP AUTO STEREO ADJUST SPK SET VCR DVD AUX TV SAT CBL PARAMATER CH.SEL 1 2 3 4 5 6 7 8 0 +10 T/V CH/LEVEL MUTE T.TONE 9 OSD MENU PTY SELECT SETUP POWER ON RDS ENTER MACRO M1 M2 STANDBY CD M3 SLEEP AUX TV SEARCH MODE DIMMER VCR DVD SAT DISPLAY CBL RETURN TUNE TUNE REMOTE CONTROL RNC-50A PRESET P.SCAN PRESET CH.SEL T/V CH/LEVEL MUTE AUTO DSP STEREO T.TONE OSD ADJUST SPK SET PARAMATER MENU SETUP ENTER 2 1 3 ENTER 4 SLEEP DIMMER 5 6 7 0 +10 8 DISPLAY 9TUNE RETURN PRESET TUNE P.SCAN PRESET MACRO M1 M2 M3 AUTO DSP STEREO REMOTE CONTROL RNC-55A ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE MENU OSD PTY SELECT SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 RDS ENTER 45 POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER ENTER SLEEP DIMMER When selecting the VIDEO SELECT DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 • Only when one of TUNER, CD, TAPE, AUX and EXTERNAL IN is selected, you can select a video input source on the VIDEO SELECT menu and enjoy the audio and video signals separately. • When dubbing them onto VIDEO 1, select either VIDEO2 or VIDEO 3 on the VIDEO SELECT menu. MACRO M2 M3 REMOTE CONTROL RNC-50A 1 Press the CURSOR UP(▲)/DOWN(▼) buttons to select the VIDEO SELECT, then press the ENTER button. V I DE O S E L E C T POWER ON AUD VCR STANDBY CD AUX TV DVD SAT SA CBL DEVICE SELECT POWER ON STANDBY CH.SEL CD T/V CH/LEVEL VCR AUX TV V I DE O 1 V I DE O 2 V I DE O 3 VOLUME MUTE DVD SAT CBL T.TONE .TONE OSD MENU SETUP OSD CH.SEL T/V ENTER CH/LEVEL MUTE SLEEP ENTER DIMMER POWER ON STANDBY T.TONE OSD DISPLAY DISPLA CD RETURN TV AUX TUNE TUNE MENU PTY SELECT VCR PRESET DVD SETUP SAT P.SCAN CBL PRESET RDS ENTER SLEEP SEARCH MODE DIMMER CH.SEL DISPLAY AUTO TUNE RETURN STEREO DSP TUNE T/V CH/LEVEL MUTE ADJUST SPK SET PRESET CD AUX 1 2 3 TAPE OSD VIDEO 1 SETUP PARAMA ARAMATER TER PRESET P.SCAN TUNER T.TONE 4 VIDEO 2 VIDEO 3 MENU SETUP AUTO 5 6 DSP EXT. IN ENTER ADJUST +10 0 SPK SET 9 ENTER STEREO 8 7 PARAMATER DIMMER SLEEP 2 1 3 MACRO DISPLAY TUNEM1 O S D : B A CK 4 RETURN TUNE M3 M2 5 6 PRESET 7 P.SCAN 8 : SE L EC T PRESET 9 0 +10 REMOTE CONTROL RNC RNC-50A 50A MACRO DSP AUTO M1 M2 STEREO M3 ADJUST SPK SET PARAMATER REMOTE CONTROL RNC-55A 1 2 3 4 5 6 7 8 9 0 +10 MACRO Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired video input source. M1 M2 M3 REMOTE CONTROL RNC-50A 2 POWER ON AUD STANDBY CD VCR AUX DVD TV SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE POWER ON T.TONE .TONE STANDBY CD MENU OSD AUX PTY SELECT VCR DVD TV SETUP SAT CBL RDS ENTER SLEEP SEARCH MODE DIMMER CH.SEL T/V DISPLAY DISPLA TUNE CH/LEVEL RETURN TUNE MUTE PRESET P.SCAN PRESET T.TONE OSD MENU SETUP AUTO DSP CD PARAMA ARAMATER TER DIMMER AUX TUNER DISPLAY CD TUNE 1 ENTER STANDBY ADJUST SPK SET SLEEP VCR STEREO ENTER POWER ON DVD TV TAPE RETURN AUX 2 TUNE 3 4 SAT CBL VIDEO 1 VIDEO 2 VIDEO 3 PRESET P.SCAN PRESET 5 6 7 9 0 +10 8 EXT. IN CH.SEL T/V AUTO CH/LEVEL DSP STEREO MUTE MACRO M2 ADJUST M3 SPK M1 SET PARAMATER T.TONE OSD 1 2 3 4 6 7 8 REMOTE CONTROL RNC RNC-55A 55A MENU SETUP 5 ENTER 9 0 SLEEP ENTER +10 DIMMER DISPLAY RETURN TUNE TUNE MACRO M1 M2 PRESET M3 P.SCAN PRESET REMOTE CONTROL RNC-50A DSP AUTO STEREO ADJUST SPK SET PARAMATER When selecting the TONE CONTROL 1 2 3 5 6 7 0 +10 9 4 8 POWER ON STANDBY MACRO CD M1 AUX M2 VCR TV M3 DVD SAT CBL REMOTE CONTROL RNC-50A ■Note: When the digital signals from DTS, Dolby Digital or MPEG program sources are input or the EXTERNAL IN is selected as an input source, you cannot select the TONE CONTROL and can hear a program source without the tone effect. CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU PTY SELECT SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST 1 STEREO 2 1 PRESET PARAMATER 3 4 Press the CURSOR UP(▲)/DOWN(▼) buttons to select the TONE CONTROL, then press the ENTER button. 5 6 7 9 0 +10 8 MACRO M1 M2 M3 REMOTE CONTROL RNC-55A T ONE CON TRO L POWER ON STANDBY AUD CD AUX TV VCR DVD SAT SA CBL TONE CON TROL DEVICE SELECT CH.SEL T/V POWER ON CH/LEVEL TV SAT OSD CBL SETUP ENTER CH.SEL POWER ON T/V SLEEP CH/LEVEL STANDBY DIMMER MUTE CD AUX DISPLAY DISPLA OSD - ENTER BA S S T RE B L E TV RETURN VCR TUNET.TONE SATOSD TUNE DVD CBL PPTY .SCAN SELECT PRESET SETUP RDS ENTER CH.SEL T/V SLEEP SEARCH MODE DIMMER CH/LEVEL MUTE DSP AUTO STEREO DISPLAY TUNE SPK SET OF F VOLUME AUX DVD PRESET MENU : STANDBY MUTE CD T.TONE .TONE VCR MENU RETURN TUNE OSD T.TONE ADJUST SETUP 0dB + -- -- -+--- -0 -- -- -+--- -0 PARAMA ARAMATER TER PRESET P.SCAN PRESET MENU PTY SELECT SETUP TUNER CD 3RDS 4 ENTER VIDEO 2 VIDEO 3 VIDEO 1 5 6 SLEEP AUTO TAPE AUX 2 1 7 MODE 8DIMMER SEARCH DSP STEREO EXT. IN 9 DISPLAY 0 SPK SET TUNE PRESET PARAMATER TUNE P.SCAN 2 1 MACRO M1 RETURN +10 ADJUST M2 : MOVE O S D : B A CK RDS ENTER PRESET 3 4 7 8 M3 5 6 AUTO DSP : CH A NGE E N T E R : SE L . STEREO 9 0 +10 REMOTE CONTROL RNC-50A RNC 50A ADJUST SPK SET PARAMATER MACRO M1 M2 1 5 M3 2 6 3 4 7 8 REMOTE CONTROL RNC-55A 9 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-55A 2 Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired mode. POWER ON AUD STANDBY CD VCR DVD AUX TV SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU PTY SELECT SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY DISPLA ■Note : • Only when the TONE CONTOL mode is set to on, the tome(BASS and TREBLE)modes can be select. RETURN TUNE TUNE PRESET P.SCAN PRESET AUTO DSP STEREO SPK SET ADJUST PARAMA ARAMATER TER TUNER CD AUX 2 1 3 VIDEO 1 5 TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-55A 55A POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE 46 ENGLISH M1 ADJUST SPK SET PARAMATER MACRO M1 M2 M3 1 2 3 4 5 6 7 8 9 0 +10 REMOTE CONTROL RNC-50A MACRO M1 M2 M3 REMOTE CONTROL RNC-55A POWER ON STANDBY CD VCR AUX TV SAT CBL DVD CH.SEL T/V CH/LEVEL MUTE T.TONE OSD POWER ON MENU STANDBY SETUP CD AUX TV SAT CBL ENTER Set the selected mode as desired. SLEEP DIMMER DISPLAY RETURN TUNE 3 VCR DVD TUNE PRESET P.SCAN CH.SEL T/V PRESET CH/LEVEL MUTE T.TONE AUTO DSP OSD STEREO MENU ADJUST SPK SET PTY SELECT PARAMATER 3 SETUP RDS ENTER SLEEP 2 1 SEARCH MODE DIMMER 4 DISPLAY 5 6 7 0 +10 RETURN TUNE 8 TUNE PRESET 9 P.SCAN PRESET MACRO ENGLISH M1 M2 M3 AUTO DSP SPK SET ADJUST STEREO PARAMATER REMOTE CONTROL RNC-50A ■When the TONE CONTROL mode is selected, press the ENTER button to select the desired mode. POWER ON VCR AUX TV SAT CBL T/V MUTE T.TONE MENU 3 4 6 7 8 9 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-55A OSD CH.SEL CH/LEVEL 2 5 ■When the BASS or TREBLE mode is selected, press the CURSOR LEFT(◀)/RIGHT(▶) buttons to adjust the tone as desired. STANDBY CD DVD 1 OSD SETUP POWER ON STANDBY CD ENTER AUD SLEEPVCR DVD AUX TV DIMMER SAT SA CBL DISPLAY SETUP RETURN TUNE DEVICE SELECT TUNE POWER ON PRESET STANDBY P.SCANCH.SEL PRESET AUD T/V CH/LEVEL CD AUX TV VOLUME MUTE VCR T.TONE .TONEDSP AUTO DVD SAT SA CBL OSD STEREO DEVICE SELECT MENU ADJUST SPK SET SETUP PARAMATER CH.SEL T/V ENTER CH/LEVEL 2 1 3 4 7 8 SLEEP 5 DIMMER 6 DISPLAY DISPLA ENTER MUTE T.TONE .TONE OSD RETURN TUNE 9 VOLUME TUNE 0 MENU +10 PRESET P.SCAN PTY SELECT SETUP PRESET RDS ENTER MACRO M1 SLEEP M2 SEARCH MODE DIMMER M3 AUTO DSP STEREO DISPLAY DISPLA RETURN TUNE REMOTE CONTROL RNC-50A PARAMA ADJUST SPK SET ARAMATER TUNER CD 3 VIDEO 1 TUNE PRESET P.SCAN PRESET TAPE AUX 2 1 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 AUTO DSP SPK SET ADJUST STEREO EXT. IN TUNER CD M2 TAPE 3 VIDEO 1 M3 PARAMA ARAMATER TER AUX 2 1 MACRO M1 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN REMOTE CONTROL RNC RNC-50A 50A MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-55A 55A • Each time this button is pressed, the mode changes as follows: POWER ON • The tone level can be adjusted within the range of -10 ~+10 dB • In general, we recommend the bass and treble to be adjusted to 0 dB(flat level) • Extreme settings at high volume may damage your speakers. RDS ENTER • To complete tone adjustment, repeat the above steps ② and ③. STANDBY CD VCR AUX TV SAT CBL DVD ON: When adjusting the tone for your taste. (“DIRECT” indicator goes off.) OFF: When listening to a program source without the tone effect.(“DIRECT”indicator lights up.) CH.SEL T/V CH/LEVEL MUTE T.TONE OSD POWER ON STANDBY CD MENU AUX SETUP TV ENTER DVD VCR SAT SLEEP CBL DIMMER DISPLAY RETURN CH.SEL TUNE TUNE T/V PRESET CH/LEVEL P.SCAN MUTE PRESET T.TONE POWER ON AUTOMENU VCR SETUP STEREO DSP ENTER ADJUST SPK SET PARAMATER SLEEP DIMMER 1 2 3 6 7 RETURN PRESET CH/LEVEL 8 P.SCAN 0 PRESET MACRO DSP M2 CBL MUTE OSD PTY SELECT SLEEP PARAMATER SEARCH MODE DIMMER DISPLAY 2 RETURN TUNE REMOTE CONTROL RNC-50A 1 3 4 6 7 8 0 +10 TUNE PRESET 5 9 P.SCAN AUTO M2 M3 PRESET DSP STEREO ADJUST SPK SET MACRO M1 SETUP RDS ENTER STEREO M3 ADJUST SPK SET TV SAT T.TONE +10 MENU AUTO M1 AUX T/V TUNE 9 DVD CH.SEL 4 DISPLAY TUNE 5 STANDBY CD OSD PARAMATER 1 2 3 4 5 6 7 8 0 +10 REMOTE CONTROL RNC-50A 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-55A POWER ON VCR STANDBY CD AUX TV DVD SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP SELECTING THE SURROUND MODE ENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO DSP SPK SET ADJUST STEREO 2 1 PRESET PARAMATER 3 4 Example) When digital signals from Dolby Digital EX 6.1 channel source are input. 5 6 7 9 0 +10 8 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A ■Notes : • Depending on the input signal format, surround back speaker setting and the selected decoding mode, the selectable surround modes may differ. • When the EXTERNAL IN is selected as input source, the SURROUND MODE cannot be selected. S URROUND MOD E DO L B Y D I G I T A L E X DO L B Y D V S R E F DO L B Y D V S W I D E 2 CH DOWNM I X POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER O S D : B A CK : SE L EC TENTER SLEEP DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A • Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired surround mode. POWER ON • In case of playing analog stereo, PCM 2 channel or Dolby Digital 2 channel source in a Dolby Headphone mode, press the CURSOR LEFT(◀)/ RIGHT(▶) buttons to select the desired listening mode. STANDBY AUD CD AUX TV VCR DVD SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET PARAMA ARAMATER TUNER CD AUX 1 2 3 VIDEO 1 5 TAPE 4 VIDEO 2 VIDEO 3 6 7 0 +10 8 EXT. IN 9 MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE MENU OSD PTY SELECT SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY RETURN TUNE PRESET AUTO TUNE P.SCAN DSP PRESET STEREO RDS ENTER 47 SETTING THE CH LEVEL SETUP : MOV E O S D : B A CK TR I M --------- CH L E V E L --------- SB - - - - - - SL - - - - - - SW - - - - - - DD L - - - - DT S L - - - - - 0 0 0 0 : CHANGE EN T E R : MEMO : MOV E O S D : B A CK TR I M ------------------- 0 0 0 0 0 : C H ANGE EN T E R : MEMO Preset memory mode ■Notes : • Depending on the speaker settings and surround mode, etc., some channels cannot be selected. • When the SPEAKER button is set to off, only the Front Left and Right channels can be selected. • Only when the digital signals from Dolby Digital or DTS program sources that include LFE signal are input, “DD L”(Dolby Digital LFE) or “DTS L” can be selected. POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP POWER ON ENTER SLEEP DIMMER DISPLAY RETURN TUNE ENTER STANDBY CD VCR DVD AUX TV SAT CBL TUNE PRESET P.SCAN PRESET Adjusting the current channel level OSD CH.SEL T/V CH/LEVEL DSP AUTO MUTE STEREO T.TONE ADJUST SPK SET OSD PARAMATER MENU 1 2 3 PTY SELECT SETUP RDS ENTER 4 SLEEP SEARCH MODE DIMMER • You can adjust the current channel levels as desired. These adjusted levels are just memorized into user’s memory(“USER”), not into preset memory(“REF. 1”, “REF. 2”) • After adjusting each channel level OSD with test tone, adjust the channel levels either according to the program sources or to suit your tastes.(For details, refer to “Adjusting each channel level with test tone” on page 32.) 5 6 7 0 +10 8 DISPLAY 9 SETUP RETURN TUNE TUNE PRESET P.SCAN PRESET MACRO POWER ON M1 M2 STANDBY M3 CD AUX AUTO REMOTE CONTROL RNC-50A VCR TV DSP DVD STEREO SAT CBL ADJUST SPK SET 2 1 PARAMATER 3 4 7 8 CH.SEL T/V 5 6 CH/LEVEL MUTE 9 0 +10 T.TONE OSD MENU PTY SELECT MACRO M1 SLEEP SETUP M2 M3 RDS ENTER SEARCH MODE DIMMER REMOTE CONTROL RNC-55A DISPLAY TUNE P.SCAN PRESET DSP STEREO Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired channel. ADJUST 2 1 1 SETUP RETURN TUNE PRESET AUTO SPK SET 5 9 PARAMATER 3 4 6 7 8 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-55A POWER ON AUD STANDBY CD VCR AUX DVD TV SAT SA CBL DEVICE SELECT CH.SEL T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU PTY SELECT SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN POWER ON PRESET STANDBY CD AUX AUTO VCR TV DSP DVD STEREO SAT CBL ADJUST SPK SET TUNER PARAMA ARAMATER TER CD AUX 2 3 1 CH.SEL VIDEO 1 TAPE 4 VIDEO 2 VIDEO 3 T/V 5 6 CH/LEVEL 7 8 MUTE EXT. IN 9 0 +10 T.TONE OSD MENU PTY SELECT MACRO M1 SLEEP SETUP M2 M3 RDS ENTER SEARCH MODE DIMMER REMOTE CONTROL RNC-55A RNC 55A DISPLAY RETURN TUNE TUNE PRESET P.SCAN PRESET AUTO DSP SPK SET ADJUST STEREO PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 MACRO M1 M2 M3 Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to adjust the level of the selected channel as desired. REMOTE CONTROL RNC-55A POWER ON STANDBY CD 2 VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU PTY SELECT SETUP RDS ENTER SLEEP SEARCH MODE DIMMER DISPLAY RETURN TUNE TUNE PRESET P.SCAN POWER ON AUD • The LFE level can be adjusted within the range of -10 ~ 0 dB and other channel levels within the range of -15 ~ +15 dB • In general, we recommend the LFE level to be adjusted to 0 dB.(However, the recommended LFE level for some early DTS software is -10 dB.) If the recommended levels seem too high, lower setting as necessary. PRESET STANDBY CD AUX AUTO VCR TV DSP DVD STEREO SAT SA CBL ADJUST SPK SET PARAMATER DEVICE SELECT 2 1 3 4 7 8 CH.SEL T/V 5 6 CH/LEVEL VOLUME MUTE 9 0 +10 T.TONE .TONE OSD MENU PTY SELECT MACRO M1 SLEEP SETUP M2 M3 RDS ENTER SEARCH MODE DIMMER REMOTE CONTROL RNC-55A DISPLAY DISPLA RETURN TUNE TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET TUNER CD 2 1 PARAMA ARAMATER TER TAPE AUX 3 VIDEO 1 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 REMOTE CONTROL RNC-55A RNC 55A POWER ON STANDBY CD VCR DVD AUX TV SAT CBL CH.SEL T/V CH/LEVEL MUTE T.TONE OSD MENU PTY SELECT SETUP RDS ENTER SEARCH MODE DIMMER RETURN TUNE PRESET 3 RDS ENTER Repeat the above steps ① and ② to adjust each channel level. SLEEP DISPLAY TUNE P.SCAN POWER ON AUX AUTO VCR PRESET STANDBY CD TV DSP DVD STEREO SAT CBL ADJUST SPK SET 2 1 PARAMATER 3 4 7 8 CH.SEL T/V 5 6 CH/LEVEL MUTE 9 0 +10 T.TONE MENU OSD PTY SELECT MACRO M1 SLEEP M2 SETUP M3 RDS ENTER SEARCH MODE DIMMER REMOTE CONTROL RNC-55A DISPLAY RETURN TUNE TUNE PRESET P.SCAN AUTO STEREO ADJUST SPK SET RDS ENTER PRESET DSP PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 MACRO M1 M2 M3 REMOTE CONTROL RNC-55A 48 ENGLISH CH L E V E L REF . 1 FL ------------C FR - - - - - - SR - - - - - - - AUTO DSP STEREO ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 REMOTE CONTROL RNC-50A POWER ON STANDBY CD VCR AUX TV SAT CBL DVD CH.SEL Memorizing the adjusted channel levels T/V CH/LEVEL MUTE T.TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY RETURN • You can memorize the adjusted channel levels into preset memory(“REF. 1”, “REF. 2”) and recall the memorized whenever you want. TUNE TUNE PRESET P.SCAN AUTO DSP STEREO ADJUST SPK SET ENGLISH PRESET PARAMATER 1 2 3 4 5 6 7 8 0 +10 9 MACRO M1 M2 M3 After performing the steps ①~③ in “Adjusting the current channel level” procedure on page 48, press the ENTER button. REMOTE CONTROL RNC-50A 1 POWER ON AUD STANDBY CD VCR AUX DVD TV SAT SA CBL DEVICE SELECT CH.SEL • The “1” of “REF. 1” indication flickers. T/V CH/LEVEL VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE ENTER TUNE PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET PARAMA ARAMATER TER TUNER CD AUX 1 2 3 VIDEO 1 TAPE 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A 2 Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired preset memory, then press the ENTER button. POWER ON POWER ON STANDBY CD VCR DVD TV SAT CBL VCR T.TONE T.TONE DISPLAY AUX SAT SA STEREO PARAMATER CH.SEL T/V 3 7 SETUP M1 SLEEPM2 ENTER 2 M1 M3 3 4 6 7 8 0 +10 MACRO M2 M3 DIMMER DISPLAY DISPLA RETURN TUNE TUNE REMOTE CONTROL RNC-50A REMOTE CONTROL RNC-50A PRESET P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET TUNER STEREO PARAMATER 9 +10 ENTER PRESET DSP ADJUST 5 8 OSD 0 MENU MACRO P.SCAN AUTO SPK SET 1 4 VOLUME MUTE 6 T.TONE .TONE 9 SETUP TUNE PRESET TV CBL DSP RETURN TUNE TUNE PRESET STANDBY CD DVD DEVICE SELECT ADJUST DIMMER DISPLAY RETURN TUNE PRESET P.SCAN POWER ON 5 SETUP ENTER SLEEP DIMMER 2 1CH/LEVEL OSD MENU SETUP ENTER SLEEP VCR OSD MUTE • Each time the CURSOR LEFT(◀) or RIGHT(▶) button is pressed, “REF. 1” or “REF. 2” is selected. • The adjusted channel levels has now been memorized into the selected memory. OSD MENU AUD CBL T/V CH/LEVEL AUTO TV SAT CH.SEL MUTE SPK SET AUX DVD T/V CH/LEVEL STANDBY CD AUX CH.SEL CD PARAMA ARAMATER TER TAPE AUX 2 1 3 VIDEO 1 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 EXT. IN MACRO M1 M2 M3 REMOTE CONTROL RNC-50A RNC 50A POWER ON POWER ON STANDBY STANDBY CD CD AUX TV DVD SAT CBL VCR VCR AUX TV SAT CBL DVD CH.SEL OSD CH.SEL T/V CH/LEVEL MUTE T/V CH/LEVEL MUTE T.TONE T.TONE OSD OSD MENU MENU SETUP SETUP ENTER ENTER SLEEP SLEEP DIMMER DISPLAY RETURN SETUP TUNE PRESET P.SCAN DSP STEREO ADJUST PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 2 Press the CURSOR UP(▲)/DOWN(▼) buttons to select the preset memory mode. MACRO M1 1 M2 Press the CURSOR LEFT(◀)/ RIGHT(▶) buttons to select the desired one of REF. 1 and REF. 2. RETURN TUNE PRESET PRESET AUTO SPK SET DIMMER DISPLAY TUNE Recalling the memorized channel levels TUNE P.SCAN AUTO PRESET DSP STEREO ADJUST SPK SET 1 2 5 9 PARAMATER 3 4 6 7 8 0 +10 MACRO M1 M2 M3 M3 REMOTE CONTROL RNC-50A REMOTE CONTROL RNC-50A POWER ON AUD AUX AUX DVD STANDBY CD STANDBY CD VCR POWER ON AUD TV SAT SA CBL DEVICE SELECT TV CH.SEL T/V VCR DVD SAT SA CBL CH/LEVEL VOLUME MUTE DEVICE SELECT T.TONE .TONE OSD CH.SEL MENU T/V CH/LEVEL SETUP VOLUME MUTE T.TONE .TONE OSD MENU SETUP ENTER SLEEP DIMMER DISPLAY DISPLA RETURN TUNE ENTER TUNE PRESET SLEEP P.SCAN PRESET DIMMER DISPLAY DISPLA RETURN TUNE TUNE AUTO PRESET P.SCAN DSP ADJUST SPK SET AUTO DSP TUNER CD VIDEO 1 CD AUX 1 2 3 VIDEO 1 TAPE 4 VIDEO 2 VIDEO 3 5 6 7 9 0 +10 8 PARAMA ARAMATER TER AUX TAPE 3 4 2 1 PARAMA ARAMATER TER TUNER STEREO ADJUST SPK SET STEREO PRESET EXT. IN VIDEO 2 VIDEO 3 5 6 7 9 0 +10 MACRO 8 M1 M2 M3 EXT. IN REMOTE CONTROL RNC RNC-50A 50A MACRO M1 M2 M3 REMOTE CONTROL RNC RNC-50A 50A • “USER” may be displayed instead of “REF. 1” or “REF. 2”. POWER ON VCR • Then the channel levels memorized into the selected preset memory are recalled. STANDBY CD AUX TV DVD SAT CBL POWER ON DVD T.TONE OSD MENU T.TONE SETUP OSD MENU SETUP ENTER DIMMER RETURN TUNE P.SCAN 9 4 7 8 0 +10 RETURN M2 P.SCAN PRESET DSP STEREO ADJUST SPK SET PARAMATER 1 2 3 4 5 6 7 8 9 0 +10 MACRO M1 TUNE AUTO PARAMATER 3 6 DIMMER PRESET STEREO ADJUST 2 5 SLEEP DISPLAY TUNE PRESET DSP 1 CBL MUTE ENTER SLEEP DISPLAY SPK SET TV SAT T/V CH/LEVEL TUNE PRESET AUX CH.SEL T/V MUTE AUTO STANDBY CD VCR CH.SEL CH/LEVEL MACRO M3 M1 REMOTE CONTROL RNC-50A M2 M3 REMOTE CONTROL RNC-50A 49 POWER ON POWER ON STANDBY CD AUX TV DVD SAT CBL STANDBY VCR VCR CD AUX TV DVD SAT CBL ENTER If a fault occurs, run through the table below before taking your receiver for repair. If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult your dealer. Under no circumstances should you attempt to repair the receiver yourself. This could void the warranty. PROBLEM POSSIBLE CAUSE REMEDY No power • The AC input cord is disconnected. • Poor connection at AC wall outlet or the outlet is inactive. • Connect the cord securely. • Check the outlet using a lamp or another appliance. No sound • The speaker cords are disconnected. • The master volume is adjusted too low. • The MUTE button on the remote control is pressed to ON. • Speakers are not switched on. • Incorrect selection of the input source. • Incorrect connections between the components. • Check the speaker connections. • Adjust the master volume. • Press the MUTE button to cancel the muting effect. • Press the SPEAKER button to ON. • Select the desired input source correctly. • Make connections correctly. No sound from the surround speakers • Surround mode is switched off(stereo mode). • Master volume and surround level are too low. • A monaural source is used. • Surround speaker setting is “N”. • Select a surround mode. • Adjust master volume and surround level. • Select a stereo or surround source. • Select the desired surround speaker setting. No sound from the center speaker • Dolby Virtual Speaker, stereo mode, etc. is selected. • Center speaker setting is “N”. • Master volume and center level are too low. • Select the desired surround. No sound from the surround back speaker • The input signal format or the current surround mode cannot support the 6.1 surround playback. • Master volume and surround back level are too low. • Surround back speaker setting is “N”. • Under the proper situations, perform the 6.1 surround playback. • Adjust master volume and surround back level. • Select the desired surround back speaker setting. Stations cannot be received • No antenna is connected. • The desired station frequency is not tuned in. • The antenna is in wrong position. • Connect an antenna. • Tune in the desired station frequency. • Move the antenna and retry tuning. Preset stations cannot be received • An incorrect station frequency has been memorized. • The memorized stations are cleared. • Memorize the correct station frequency. Poor FM reception • No antenna is connected. • The antenna is not positioned for the best reception. • Connect an antenna. • Change the position of the antenna. Continuous hissing noise during FM reception, especially when a stereo broadcast is received. • Weak signals. • Change the position of the antenna. • Install an outdoor antenna. Continuous or intermittent hissing noise during AM reception, especially at night. • Noise is caused by motors, fluorescent lamps or lightning, etc. • Keep the receiver away from noise sources. Remote control unit does not operate. • Batteries are not loaded or exhausted. • The remote sensor is obstructed. • Replace the batteries. • Remove the obstacle. Other Sherwood components do not react to remote control commands. • DIGI LINK connections are not made properly. • Make proper DIGI LINK connections. OSD function is not available • Video connections between this unit and the TV monitor are not made correctly. • Make proper video connections. • Select the desired center speaker setting. • Adjust master volume and center level. • Memorize the stations again. • Install an outdoor AM antenna. 50 ENGLISH Troubleshooting Guide ENGLISH Specifications AMPLIFIER SECTION ×100 W • Power output, stereo mode, 6 Ω, THD 0.2 %, 40 Hz~20 kHz | 2× • Total harmonic distortion, 6 Ω, 95 W, 1 kHz | 0.09% • Intermodulation distortion 60 Hz : 7 kHz= 4 : 1 SMPTE, 6 Ω, 95 W | 0.1% • Input sensitivity/impedance Line (CD, TAPE, VIDEO) | 230 mV/47kΩ • Signal to noise ratio, IHF “A” weighted Line (CD, TAPE, VIDEO) | 90 dB • Frequency response Line (CD, TAPE, VIDEO), 20 Hz~50 kHz | +0, -3 dB • Output level TAPE REC, 2.2 kΩ | 200 mV • Bass/Treble control, 100 Hz/10 kHz | ±10 dB • Surround mode, only channel driven Front power output, 6 Ω, 1 kHz, THD 0.7 % | 110 W+110 W Center power output, 6 Ω, 1 kHz, THD 0.7 % | 110 W Surround power output, 6 Ω, 1 kHz, THD 0.7 % | 110 W+110 W Surround back power output, 6 Ω, 1 kHz, THD 0.7 % | 110 W DIGITAL AUDIO SECTION • Sampling frequency | 32, 44.1, 48, 96 kHz • Digital input level Coaxial, 75 Ω | 0.5 Vp-p Optical, 660 nm | -15~-21 dBm VIDEO SECTION • Video format | NTSC • Input sensitivity(=Output level), 75 Ω Video (Composite(normal)) | 1 Vp-p S-Video (luminance signal) | 1 Vp-p (chrominance signal) | 0.286 Vp-p Component video (R-Y signal) | 0.5 Vp-p (B-Y signal) | 0.5 Vp-p (Y signal) | 1.0 Vp-p FM TUNER SECTION • Tuning frequency range | 87.5~108 MHz • Usable sensitivity, THD 3%, S/N 30 dB | 12.8 dBf • 50 dB quieting sensitivity, mono/stereo | 20.2 / 45.3 dBf • Signal to noise ratio, 65 dBf, mono/stereo | 70 / 65 dB • Total harmonic distortion, 65 dBf,1 kHz, mono/stereo | 0.5 / 0.8 % • Frequency response, 30 Hz~15 kHz | ±3 dB • Stereo separation, 1 kHz | 32 dB • Capture ratio | 4.0 dB • IF rejection ratio | 60 dB AM TUNER SECTION • Tuning frequency range | 520~1710 kHz • Usable sensitivity | 500 µV/m • Signal to noise ratio | 40 dB • Selectivity | 25 dB GENERAL • Power supply | 120 V ~ 60 Hz • Power consumption | 2.7 A • Switched AC outlets | TOTAL 100 W, 1 A max. ×141× ×330 mm(17-3/8× ×5-1/2× ×13 inches) • Dimensions (W×H×D) | 440× • Weight (Net) | 10.1 kg (22.3 Ibs) Note: Design and specifications are subject to change without notice for improvements. 51 Setup Code Table AOC Admiral Aiko Akai Alaron Ambassador America Action Ampro Anam Audiovox Baysonic Belcor Bell & Howell Bradford Brockwood Broksonic CXC Candle Carnivale Carver Celebrity Cineral Citizen Concerto Contec Craig Crosley Crown Curtis Mathes Daewoo Daytron Denon Dumont Dwin Electroband Emerson Envision Fisher Fujitsu Funai Futuretech GE Gibralter 005 041 014 005 026 024 027 043 027 030 027 003 019 027 003 028 027 005 005 010 050 030 012 011 027 027 010 027 007 012 022 030 003 016 002 044 050 019 003 005 019 026 027 027 007 004 002 003 031 047 027 048 014 Goldstar Gradiente Grunpy Hallmark Harley Davidson Harman/Kardon Havard Hitachi Infinity Inteq JBL JCB JVC KEC KTV Kenwood LG LXI Logik Luxman MGA MTC Magnavox Magestic Marantz Matsushita Magatron Memorex 049 034 001 031 011 014 005 006 010 005 032 003 011 019 016 038 006 006 008 011 040 014 014 030 001 041 006 034 035 Midland Minutz Mitsubishi Motorola Multitech NAD NEC NTC Nikko Onwa Optimus Optonica Orion Panasonic Penney 003 036 028 026 031 006 026 023 008 015 005 030 038 003 027 024 041 040 029 034 029 025 035 025 Pilco Philips 52 005 009 027 025 026 010 027 016 010 002 010 050 009 027 027 005 011 007 001 011 017 012 010 001 010 042 025 019 001 007 004 041 041 027 020 005 014 005 027 019 041 028 008 007 004 010 010 025 011 026 003 011 018 ENGLISH TV 011 046 005 003 003 010 006 019 020 005 005 005 025 003 026 003 011 016 042 031 017 025 002 008 006 015 017 025 003 025 003 022 011 025 014 042 021 031 042 020 003 031 022 025 005 011 026 008 011 005 012 006 016 005 015 003 025 040 ENGLISH Pilot Pioneer Portland Prism Proscan Proton Pulsar Quasar RCA Radio Shack Realistic Runco SSS Sampo Samsung Samsux Sansei Sansui Sanyo Scimitsu Scotch Scott Sears Semivox Semp Sharp Sherwood Shogun Signature Sony Soundesign Squareview Starlite Supreme Sylvania Symphonic TMK Tandy Technics Technoi Ace Techwood Teknika Telefunken Toshiba Totevision Vector Research Victor Vidikron 005 022 003 008 007 025 002 008 007 037 007 003 019 011 002 027 005 012 006 030 031 019 003 025 028 007 011 027 020 041 000 003 001 050 027 023 027 050 010 023 025 041 008 026 008 010 011 011 019 006 005 009 010 003 006 006 014 032 003 042 008 038 019 011 021 006 005 003 006 005 White Westinghouse Yamaha Zenith 021 041 039 021 006 027 003 040 027 013 015 005 025 005 025 003 025 025 019 021 006 003 003 020 011 026 025 Admiral Adventura Aiko Aiwa Akai America Action America High Asha Audiovox Beaumark Bell & Howell Brocksonic Broksonic CCE Calix Canon Carver Cineral Citizen Colt Craig Curtis Mathes Cybernex Daewoo Denon Dynatech Electrohome Electrophonic Emerex Emerson 045 026 026 005 011 024 Fisher Fuji Funai GE Garrard Go Video GoldStar Gradiente HI-Q Harley Davidson Harman/Kardon Harwood 042 011 027 001 017 006 020 012 012 014 003 025 010 026 031 005 002 003 021 011 034 003 031 027 000 025 005 026 025 004 023 005 023 017 021 020 015 005 004 081 025 005 015 005 013 023 010 008 000 005 005 002 005 001 012 004 000 013 000 052 005 000 012 000 016 015 021 005 001 035 025 004 001 014 021 001 023 026 015 028 024 020 025 017 003 000 018 009 004 027 023 003 VCR 033 027 010 006 025 Vidtech Wards 026 53 000 018 025 025 012 004 025 006 006 021 Minolta Mitsubishi Motorola Multitech NEC Nikko Noblex Olympus Opimus Orion Panasonic Penny Pentax Philco Philips Pilot Pioneer Profitronic Proscan Protec Pulsar Quarter Quartz Quasar RCA Radio Shack Radix Randex 011 000 008 014 026 005 015 014 004 005 000 015 004 023 023 023 025 004 023 004 005 004 004 000 008 027 004 000 017 005 023 004 005 031 020 004 004 008 004 004 005 014 023 013 015 007 011 011 004 013 000 005 005 Realistic 008 026 Runco STS Samsung Sanky Sansui Sanyo Scott Sears 026 025 026 005 006 Semp Sharp Shintom Shogun Singer Sony Syvania Symphonic TMK Tatung Teac Technics Teknika Thomas Toshiba Totevision Unitech Vector Vector Research Video Concepts Videosonic Wards 009 000 007 016 000 019 028 005 017 029 027 021 007 011 012 031 014 027 015 014 009 016 027 032 021 028 005 026 006 017 028 029 001 022 023 029 008 031 006 023 032 030 White WestingHouse XR-100 Yamaha Zenith Ameira High Brocksonic Colt Cutis Mathes Daewoo Emerson Funai GE 021 016 028 004 029 027 031 023 008 Hitachi HQ Lloyds MGA Megavox 019 54 004 011 007 008 023 027 000 012 020 004 011 010 027 015 023 015 004 004 000 023 026 000 004 004 000 010 005 023 010 006 010 023 013 000 005 027 012 000 010 007 014 023 010 005 033 021 017 018 012 026 011 009 000 024 002 016 000 000 003 009 026 028 005 000 017 ENGLISH Headquarter Hitachi Hughes Net.Sys JVC Jensen KEC KLH Kenwood Kodak LXI Lloyd’s Logik MEI MGA MGN Technology MTC Magnasonic Magnavox Magnin Marantz Marta Matsushita Memorex 008 017 016 023 009 023 004 008 027 015 021 025 004 000 015 006 007 000 021 004 (TV use 008) 001 015 004 (TV use 008) 025 001 000 004 (TV use 008) 027 (TV use 041) 004 (TV use 008) 000 000 023 016 (TV use 010) 000 012 019 003 013 (TV use 012) 023 000 004 (TV use 008) ENGLISH Magnin Memorex Mitsubishi Orion Panasonic Penney Quasar RCA Sansui Sanyo Sear Sharp Sony Symphonic Zenith 023 005 028 (TV use 025) 027 (TV use 041) 001 004 (TV use 008) 028 (TV use 042) 004 (TV use 008) 023 028 (TV use 042) 004 (TV use 008) 028 (TV use 042) 013 (TV use 012) 004 (TV use 008) 027 (TV use 041) 000 023 000 005 027 (TV use 041) 002 (TV use 000) 000 000 CBL ABC Allegro Archer Bell&Howell Century Citizen Comtronics Contec Easten Emerson Everquest Focus Garrard Gemini General Instrument GoldStar Goodmind Hamlin Hitachi Hytex Jasco Jerrold DVD Harman/Kardon JVC Kenwood Megavox Mitsubishi Onkyo Panasonic Philips Pioneer Proscan RCA Samsung Sherwood Sony Technics Theta Digital Toshiba Yamaha Zenith 009 008 005 011 016 011 013 011 003 002 002 017 001 020 004 013 014 011 013 011 006 014 012 021 Memolex Movie Time NSC Oak Optimus Panasonic Paragon Philips Pioneer Popular Mechanics Pulsar Quasar RCA Radio Shack Recoton Regal Regency Rembrandt Runco SL Marx Smasung Scientific Atlanta Signal Signature Sprucer Starcom 026 000 022 018 023 019 025 007 010 55 002 007 018 018 009 018 018 014 011 001 026 010 022 018 010 003 006 021 026 009 008 030 033 017 026 012 006 007 010 002 006 000 015 015 011 031 000 000 018 017 022 000 000 031 010 022 012 001 006 000 014 017 003 010 006 031 002 276 040 006 034 020 004 013 018 007 034 021 033 032 016 031 021 014 025 021 026 028 030 027 020 014 023 014 010 009 010 010 010 015 014 007 000 010 018 007 153 015 000 022 014 AUX-LD 026 Denon Mitsubishi NAD Pioneer Sony 008 008 001 009 009 016 009 011 007 009 016 006 006 006 017 006 016 003 018 014 004 018 010 006 013 AUX-TAPE 024 Aiwa Carver Harman/Kardon JVC Kenwood Megavox Marantz Onkyo Opimus Panasonic Pioneer Sansui Sony Technics Victor Wards Yamaha 015 018 015 005 005 015 000 005 004 004 016 022 008 004 004 012 002 038 002 004 021 038 024 002 010 034 004 024 025 020 020 011 014 026 009 AUX-AMP 002 012 Awia Carver Curtis Mathes Denon Harman/Kardon Linn Megavox Marantz Panasonic Philips Pioneer Sony Technics Wards Yamaha 014 AUX-TAPE/MD Sherwood 018 019 SAT AlphaStar Chaparral Echostar Expreevu General Instrument HTS Hitachi Hughes Net.Sys JVC Jerrold Megavox Memorex Next Level Panasonic Philips Primestar RCA Radio Shack Realistic Sony Star Choice Toshiba Uniden Zenith 007 007 007 007 017 ENGLISH Stargate Starquest TV86 Teleview Tocom Toshiba Tusa Unika United Artists Universal Viewstar Zenith Zentek 000 (for tape deck) 035 (for MD recorder) 56 029 023 027 037 040 023 023 023 039 023 003 019 039 003 028 040 027 033 ENGLISH AUX-HOME AUTOMATION GE Lutron One For All Radio Shack Security System Universal X10 X10 Kenwood Krell LXI Linn MCS MTC Megavox Marantz Mission NSM Nikko Onkyo Opimus 043 044 042 043 042 042 042 AUX-DBS Awia Fisher Harman/Kardon JBL JVC Jerrold RCA Scientific Artlanta Sony Starcom 045 005 046 046 047 031 006 032 045 031 059 Panasonic Parasound Philips Pioneer Proton QED Quasar RCA Realistic Rotel SAE Sansui Sanyo Scott Sears Sharp Sherwood 029 AUX-ACCESSARY Archer GC Electronics Jebsee Rabbit Radio Shack 013 013 013 036 013 Sony Soundesign Tascam Teac Technics Victor Wards Yamaha Yorx CD Awia Burmester California Audio Lab Carver DKK Denon Emerson Fisher Garrard Genexxa Harman/Kardon Hitachi JVC 010 019 002 010 001 028 035 012 019 004 010 004 007 030 012 020 034 033 018 035 011 57 003 010 035 010 002 019 010 002 010 010 033 008 001 019 002 019 010 004 010 010 002 012 012 010 010 010 012 035 035 029 013 000 001 009 019 019 002 007 010 005 032 029 016 035 010 013 026 004 009 031 023 035 035 019 019 024 025 012 021 035 020 029 021 017 006 013 036 035 013 027 037 038 014 022 018 031 033 006 015 039 013 040 041 RD-8601 Audio/Video Receiver 5707-21128-013-0