Download Bosscom BEO4 User manual
Transcript
®Powmascables BOSSCOM DAB/FM Tuner Compatible with B&O Remote Controls User Manual ®Powmascables ®Powmascables Everyday control with Beo4, Beo5, Beo6 Everyday control with Beolink 1000 Special commands, used only by initial installation Special commands, used by initial installation *1 Not all Bang & Olufsen equipment responds to numeric commands. Using the Direct Mode option is recommended. ®Powmascables ®Powmascables List of Contents Getting started ........................................................................................................ page 5 Direct or CableLink mode ........................................................................................ page 5 Factory settings ....................................................................................................... page 5 Installation .............................................................................................................. page 6 Connection to B&O Equipment ................................................................................ page 6 Antenna connection ................................................................................................ page 7 Automatic power on and off .................................................................................... page 7 Option programming ............................................................................................... page 8 Source & Option selection. ................................................................................... page 9 BeoSound5, Encore, BeoCenter2 ................................................................ BeoSound4, BeoSound1 ............................................................................. BeoSound Century, BeoSound 9000, BeoSound 3000/3200 ........................ BeoSoundOuverture, BeoSystem 2500, BeoCenter 2500 ............................. BeoCenter 2300, BeoMaster 3300/3500/4500/ 5500/6500/7000 ............... BeoCenter 8000/ 8500/9000/9300/9500 .................................................... BeoSystem 3 ............................................................................................... BeoLink Converter 1611/ 1612 .................................................................... BeoLink Active ............................................................................................. Bang & Olufsen TV, all models .................................................................... page page page page page page page page page page 9 10 11 12 13 14 15 16 17 18 o o o o o o o o o o ®Powmascables ®Powmascables BOSSCOM DAB/FM is equipped with a 7 pin DIN Data Link cable for connection to Bang & Olufsen equipment. Thus an adaptor cable is required for connection to equipment not having a DIN input socket. See below examples and the Option Programming section page 8. ®Powmascables ®Powmascables Getting Started This BOSSCOM DAB/FM tuner has been designed for operation in a Bang & Olufsen remote control system allowing full control with a Bang & Olufsen remote control terminal either directly or via connection to Bang & Olufsen equipment. Thus the tuner is Beolink compatible. Direct Mode or CableLink Mode The BOSSCOM DAB/FM tuner is connected to Bang & Olufsen equipment via the 7-pin DIN cable with or without adaptor, and through option programming it may be controlled as follows: 1. Via the tuner’s built in IR-receiver, ”Direct Mode” Direct Mode is used when connection to an input with control data is not possible. 2. Via the cable connected Bang & Olufsen equipment, ”CableLink Mode” CableLink Mode is used only when connection to an input with control data is possible. See page 8 for Option Programming. Factory Settings The factory setting is for “Direct Mode” and manual power control. The factory setting for input socket and selected source is: Remote control Beo4, Beo5 or Beo6 Beolink 1000 Source N.MUSIC, A.MEM2 or TAPE2 SHIFT A.TAPE If the DAB/FM tuner is connected to a different input, the option should be programmed accordingly. See page 8 for Option Programming ®Powmascables ®Powmascables Installation 1) 2) 3) 4) 5) 6) 7) 8) Connect power supply. Connect external antenna if required. Turn the power switch on, located on the cabinet. Select option and complete option programming, if required. Connect the tuner to the correct input socket on the Bang & Olufsen equipment. Select the corresponding source on the remote control terminal. Turn on the tuner manually, if it is not in the automatic power up mode. Select and program your favorite stations. Connection to Bang & Olufsen Equipment This BOSSCOM DAB/FM tuner may be connected to any Bang & Olufsen BeoSound, BeoCenter, BeoMaster, BeoSystem or BeoVision TV and controlled with a Bang & Olufsen remote control terminal, but it may also be connected to equipment of any other brand and still be controlled with the Bang & Olufsen remote control terminal. Through the years Bang & Olufsen equipment has had input sockets added, removed and renamed. A newer Bang & Olufsen remote control has the button N.MUSIC, which is identical to SHIFT A.TAPE or A.TAPE2 on older remotes. Below tables are showing available input sockets and their designation on various Bang & Olufsen equipment. The tables below also show the source that has to be selected to open a given input. Thus with identified Bang & Olufsen equipment and the selected input socket the required option for the tuner to be operable may be determined. Some input sockets allow for the CableLink option to be selected, whereas most of the newer audio equipment requires the Direct Mode option to be used. The Direct Mode Option: The tuner is controlled directly with the Bang & Olufsen remote control terminal. Control from a linkroom is not possible, although the tuner may be listened to there. The CableLink Option: The tuner is controlled with the Bang & Olufsen remote control terminal through the connected Bang & Olufsen equipment sending control data via the connection cable. The tuner may be controlled from any linkroom too. CableLink Direct Mode The CableLink option allows for the tuner to be listened to and controlled from any linkroom. The Direct Mode option allows for the tuner to be listened to but not controlled from any linkroom. The Direct Mode option works in any Bang & Olufsen set up, but the tuner’s IR receiver is not plasma safe. ®Powmascables ®Powmascables Antenna Connection BOSSCOM DAB/FM tuner may be connected to any antenna designed for FM and the DAB reception, if the supplied one is not sufficient. o o o If the FM signal strength is not sufficient the reception will be noisy. If the DAB signal strength is not sufficient the reception is varying from disturbing ”bubbles” to complete quietness. If no signal is received the display indicates N/A. Automatic Power Up and Down As default factory setting the tuner is manually powered up and down with the button. As the display is automatically dimmed 10 seconds after any operation, powering the tuner down is not a strict requirement. If automatic powering up and down with the source selection is desired, programming a specific option allows for that. Option Code Option 990 Option 991 Function The tuner can only be powered up and down, using button. the The tuner automatically powers up and down. Important Info about the Automatic Power Mode When the automatic power option has been set, the tuner turns on and off automatically with the source selection. But if the tuner’s clock has not been set, automatic power up and down is NOT possible. The clock is automatically set 10-30 seconds after power has been applied to the tuner, provided a DAB station has been received. Thus the automatic power option cannot be used if the tuner is switched off the mains regularly. Menu Pressing Use the • • • • enters the tuner’s main Menu. buttons to select one of the sub menus: Manual scan Contrast System reset Software version ®Powmascables ®Powmascables Option Programming Option programming is required only when installing the tuner. The programming is performed with a Bang & Olufsen remote control terminal by initiating a 5 button sequence within 8 seconds after powering up the tuner. When powering up the tuner the red control LED flashes for 8 seconds, and the programming has to be carried out before the control LED stops flashing. When entering a button the timeout is prolonged with another 8 seconds. If not successful the operation may be repeated. Programming starts by pressing All options have 3 digits to be entered in between. and ends by pressing Option 106 is entered like this: *1 Control LED Indications Red/green flash By initial power up the LED starts flashing red/green, indicating that the tuner is in Option Programming Mode, i.e. an option may be entered. The Option Programming Mode is terminated after 30 seconds or prior hereto if any command , or is received. except for Red The tuner is powered down. Green The tuner is powered up or the tuner is searching for a signal to set the clock. Intermittently turned off The LED turns off very briefly as a command handshake indicator. *1. If using a Beolink1000 remote control, LIGHT must be replaced with SHIFT-LINK. ®Powmascables ®Powmascables Source & Option Selection The following tables show the available input sockets on various Bang & Olufsen audio and video products, how to select them using a remote control terminal and what the corresponding option program of the BOSSCOM DAB/FM tuner should be. The BOSSCOM DAB/ FM tuner has to be programmed with the right option to operate correctly: Input Socket BeoSound 5 Source Selected MasterLink Direct Option CableLink Option Remarks - 410 - 416 - 412 If the MasterLink socket is not used, the DAB/FM tuner might be connected and operated via a BeoLink Converter. See page 16 for details on connection of the BeoLink Converter 1611. Input Socket BeoSound 5 Encore Source Selected LINE-IN Direct Option CableLink Option Remarks 100 - The Encore input is a mini jack socket. Use BOSSCOM adaptor cable, type 39207437. Input Socket BeoCenter 2 ®Powmascables AUX-IN Source Selected Direct Option CableLink Option Remarks 100 - The input is RCA phono sockets. Use BOSSCOM adaptor cable, type 39207438. ®Powmascables BeoSound 4 AUX 100 - The input is RCA phono sockets. Use BOSSCOM adaptor cable, type 39207438. MasterLink - 410 - 416 If the MasterLink socket is not used, the DAB/FM tuner might be connected and operated via a BeoLink Converter. - 412 Direct Option CableLink Option AUX 100 - AUX 102 - Input Socket BeoSound 1 ®Powmascables Source Selected See page 16 for details on connection of the BeoLink Converter 1611. Remarks ®Powmascables Input Socket BeoSound Century Direct Option CableLink Option AUX 103 - AUX 106 - AUX 100 - Direct Option CableLink Option AUX 100 - AUX 102 - Direct Option CableLink Option AUX 100 - AUX 102 - AUX 103 - AUX 106 - Input Socket BeoSound 9000 Input Socket BeoSound 3000 BeoSound 3200 ®Powmascables Source Selected Source Selected Source Selected Remarks Remarks Remarks ®Powmascables BeoSound Ouverture AUX 103 302 In the CableLink mode numeric commands are not accepted. AUX 106 206 In the CableLink mode numeric commands are not accepted. AUX 100 - In the CableLink mode numeric commands are not accepted. MasterLink - 410 - 416 - 412 If the MasterLink socket is not used, the DAB/FM tuner might be connected and operated via a BeoLink Converter. See page 16 for details on connection of the BeoLink Converter 1611. Input Socket BeoSystem 2500 BeoCenter 2500 ®Powmascables Direct Option CableLink Option Remarks AUX 100 - In the CableLink mode numeric commands are not accepted. AUX 103 302 In the CableLink mode numeric commands are not accepted. AUX 106 206 In the CableLink mode numeric commands are not accepted. Source Selected ®Powmascables Input Socket BeoCenter 2300 Direct Option CableLink Option Remarks AUX 100 300 AUX 102 302 AUX 103 303 In the CableLink mode numeric commands are not accepted. In the CableLink mode numeric commands are not accepted. In the CableLink mode numeric commands are not accepted. AUX 106 306 In the CableLink mode numeric commands are not accepted. CableLink Option 302 Remarks TP Direct Option 102 CD 104 204 TP1 Direct Option 102 CableLink Option 302 CD 104 204 TP2 103 302 PHONO 106 206 Input Socket BeoMaster 3300 Source Selected Source Selected BeoMaster 5500 Input Socket BeoMaster 3500 BeoMaster 4500 ®Powmascables Source Selected In the CableLink mode numeric commands are not accepted. In the CableLink mode numeric commands are not accepted. Remarks In the CableLink mode numeric commands are not accepted. In the CableLink mode numeric commands are not accepted. In the CableLink mode numeric commands are not accepted. In the CableLink mode numeric commands are not accepted. ®Powmascables Input Socket BeoMaster 6500 BeoMaster 7000 TP1 Direct Option 102 CableLink Option 302 CD 104 204 TP2 103 302 PHONO 106 206 Direct Option CableLink Option Remarks 103 302 In the CableLink mode numeric commands are not accepted. Direct Option CableLink Option Remarks TAPE2 103 302 In the CableLink mode numeric commands are not accepted. AUX 100 - Direct Option CableLink Option Remarks PHONO 106 206 In the CableLink mode numeric commands are not accepted. TAPE2 103 302 In the CableLink mode numeric commands are not accepted. AUX 100 - Input Socket BeoCenter 8000 Input Socket BeoCenter 9300 ®Powmascables Source Selected TAPE2 Input Socket BeoCenter 8500 BeoCenter 9000 BeoCenter 9500 Source Selected Source Selected Source Selected Remarks ®Powmascables Input Socket BeoSystem 3 Direct Option CableLink Option Remarks AV1 AV2 AV3 - 410 414 412 The input is a scart socket, 21 pin AV socket. Use BOSSCOM adaptor cable, type 39207496. AV4 AV5 AV6 - 410 414 412 The input is RCA phono sockets. Use BOSSCOM adaptor cable, type 39207438. MasterLink Source Selected etc. - If the MasterLink socket is not used, the DAB/FM tuner might be connected and operated via a BeoLink Converter. See page 16 for details on connection of the BeoLink Converter 1611. ®Powmascables ®Powmascables Connection via BeoLink Converter 1611/1612 BOSSCOM DAB/FM tuner may be connected to a Bang & Olufsen stand-alone audio or video master, TV, via a BeoLink Converter using MasterLink and the AAL inputs. Connected to an audio master and programmed as an ”video source” the DAB/FM tuner may be selected as that, VMEM as an example. Connected to a video master and programmed as an “audio source” the DAB/FM may be selected as that, ATAPE as an example. Notice that Bang & Olufsen equipment has to be programmed in option 2. See the relevant Bang & Olufsen user guide. Input Socket BeoLink Converter 1611 or 1612 used with a Bang & Olufsen audio master and BOSSCOM DAB/FM tuner. Direct Option CableLink Option Remarks AAL - 410 AAL - 412 AAL - 414 BOSSCOM DAB/FM connects to the BeoLink Converter with BOSSCOM VSNUT adaptor cable, type 39207434. AAL - 416 Source Selected The BeoLink Converter 1611 connects to a stand-alone Bang & Olufsen audio master with a MasterLink cable. Connection of more Bang & Olufsen equipment might create control conflicts. Input Socket BeoLink Converter 1611 or 1612 used with a Bang & Olufsen TV and the DAB/FM. Direct Option CableLink Option Remarks AAL - 402 AAL - 404 AAL - 406 The DAB/FM connects to the BeoLink Converter with BOSSCOM ASNUT adaptor cable, type 39207432. AAL - 408 Source Selected The BeoLink Converter 1611 connects to a stand-alone Bang & Olufsen TV with a MasterLink cable. Connection of more Bang & Olufsen equipment might create control conflicts. ®Powmascables ®Powmascables Connection via BeoLink Active in any Link Room BOSSCOM DAB/FM tuner may be connected to a Bang & Olufsen BeoLink Active with a vacant ‘PC’ socket. Thus active speakers in any link room allow for the installation of the DAB/FM tuner and the opportunity of having a local radio source controlled directly with the Bang & Olufsen remote control terminal. Input Socket BeoLink Active ®Powmascables PC Source Selected Direct Option CableLink Option Remarks 118 - The DAB/FM connects to the BeoLink Active with BOSSCOM PCSNUT adaptor cable, type 39207436. ®Powmascables Connection to 21 Pin AV Socket on any Bang & Olufsen TV Input Socket All B&O TV models Scart BeoVision 10 BeoVision 8 BeoVision 7 BeoVision 6 BeoVision 4 BeoVision 3 BeoVision 1 BeoSystem 3 Avant models LX models LE models LS models L models MX models ME models AV1 - AV6 ®Powmascables NOT the DECODER input!! Source Selected Direct Option CableLink Option Remarks 110 410 110 410 The input is a scart socket, 21 pin AV socket. Use BOSSCOM adaptor cable, type 39207496. 116 416 112 412 114 414 Check the TV user guide for programming of the AV connections.