Download Wolf IDF606CG Specifications
Transcript
INTERNATIONAL DESIGN GUIDE CONTENTS Wolf Built-In Ovens 4 Wolf Electric Cooktops 9 Wolf Gas Cooktops 14 Wolf Integrated Modules 19 Wolf Warming Drawers 30 Wolf Dual Fuel Ranges 34 Wolf Sealed Burner Rangetops 40 Wolf Gas Ranges 46 Wolf Gas Rangetops 53 Wolf Cooktop Ventilation 57 Wolf Ventilation Recommendations 67 Features and specifications indicated herein and on our website are subject to change at any time without notice. Check our website, wolfappliance.com for the most up-to-date specifications. IMPORTANT NOTE As you follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and efficient installation of Wolf equipment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. WOLF ® is a registered trademark of Wolf Appliance, Inc. Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problem-free installation. WELCOME TO WOLF APPLIANCE In this Design Guide, you’ll find all the necessary information for specifying a Wolf oven, cooktop, range, rangetop or ventilation equipment into the next kitchen or home you design. Each unit is handcrafted with the knowledge and experience gleaned from being the premier supplier of cooking equipment to professional chefs and their restaurants for nearly 75 years. Sub-Zero, a corporate companion and kitchen soul mate, shares the identical values and pride we take in providing the best cooking equipment. A Wolf is beautiful and will complement any design you use, whether it be contemporary or traditional. But that’s not why many customers turn to us. We have a passion for cooking and it shows in our work. Consumers appreciate the unique features we have built in to our many different models. You can refer to specifics as you page through this guide. The features are as numerous as the various units you have to choose from. But one of the more prominent highlights is the Wolf Dual Convection System that is in all our built-in ovens and dual fuel ranges. It delivers even temperature and airflow throughout the oven. Its combination of fans and heating elements operate either simultaneously or in sequence, depending on which of the ten different cooking modes your client chooses. Our electric cooktops are unique to the industry with their capabilities of providing simmer on all elements and the melt feature on one of the elements. The triple element on the 914 mm cooktop can generate up to 2,700 watts for those large pots that need fast boiling. If you are looking for cooking performance, but don’t want to shout it out in your kitchen design, one of our unframed electric cooktops may be your choice. There’s no stainless steel trim, just the sophisticated black ceramic glass top that can be mounted flush with the top of the countertop or as a frameless installation sitting on top of the countertop surface. The sizes, alternative tops, and selection of the standard classic stainless steel and the premium finishes of carbon or platinum stainless steel make your decision-making process much more fun for you and your clients. Now you can give them exactly what they want without sacrificing the quality they demand. In all your applications you can depend on Wolf. That reputation is even stronger because it is backed by Sub-Zero. The combination of the two is really greater than their sum. Review this Design Guide in greater detail when you get a chance and keep it as a handy reference. We are confident you will like what you see. In addition, our dual-stacked burners on the gas cooktops, dual fuel ranges and sealed burner rangetops are all sealed and offer you the capability of simmering foods. 3 B U I LT- I N O V E N S Model ISO30U/S Model ISO36U/S W O L F L S E R I E S B U I LT- I N O V E N S FEATURES It’s hard to put into a few words the differences you will see in the Wolf L Series ovens compared to others on the market. Some of those differences are very dramatic. Did you notice that the control panel closes? It’s an attractive feature and will enable you to hide that control panel that many of us have labored to make functional and tried to make beautiful. Dual convection logic control system Inside, the beauty, design and functionality continue. Brilliant halogen lights illuminate the beautiful blue interior. As you open the oven door, feel the smoothness of the door damper system. Pull that bottom oven rack all the way out and notice how it is nestled on the door rails. With the dual convection fans, all models offer ten different cooking modes. Three removable racks, six-level rack guide and full-extension bottom rack—five-level rack guide for 914 mm oven Ten cooking modes—bake, roast, broil, convection bake, convection roast, convection broil, convection, bake stone (accessory required), proof and dehydrate (accessory required) Rotating glass touch control panel Cobalt blue porcelain oven interior Large viewing triple-pane window Dual interior halogen lighting Hidden bake element and recessed broil element Temperature probe and receptacle Self-clean, delayed start and Sabbath features Door hinge with hydraulic damper assures smooth opening and closing of the door Model IDO30U/S Factory-installed trim This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. L S E R I E S O V E N F E AT U R E S Model ISO30U/S shown Electronics and door cooling vents Rotating electronic control panel Recessed broil element Oven door light switch Thermostat Location of rating plate Three removable racks Probe receptacle Hidden bake element Halogen lights Door hinge with hydraulic damper Exhaust vent Removable six-level rack guide 4 Triple-pane window Gasket B U I LT- I N O V E N S PLANNING INFORMATION ELECTRICAL REQUIREMENTS There are only three different sizes to consider when planning for your layout. You can choose either a 762 mm or 914 mm built-in single oven or a 762 mm double oven. International (I) models come with a factory installed transformer and require a 220-240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. The appropriate electrical connection must be provided in accordance with local requirements. For ease of installation, Wolf recommends using 838 mm wide cabinets with 762 mm ovens and 991 mm wide cabinets with the 914 mm oven. You will need a minimum 610 mm of usable cabinet depth. The cabinet must be able to support 113 kg for a single oven and 181 kg for a double oven. Wolf built-in ovens have a face trim on all four sides and will overlap stiles and rails. The trim overlaps 3 mm on the bottom, 5 mm on the top and 19 mm on each side. Specifications on the following pages provide overall dimensions, rough openings and installation specifics for the three different oven sizes. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation. IMPORTANT NOTE: Unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in an adjacent cabinet within reach of the conduit. A 51 mm diameter hole to route the conduit through cabinetry will be required. Refer to the Installation Specifications illustrations on the following pages for location of the electrical supply. You must follow all local codes and ordinances when installing your service. A Wolf single oven may be installed below an electric or gas cooktop. Wolf built-in ovens are designed and agency approved for installation with Wolf cooktops only. Refer to the electric and gas cooktops sections for additional specifications. A built-in oven cannot be installed below a Wolf rangetop. MODEL OPTIONS Built-In Ovens 762 mm Single Oven – Unframed Classic Stainless ISO30U/S This appliance must be installed in accordance with local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit that is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency and amperage ratings are listed on the product rating plate. 914 mm Single Oven – Unframed Classic Stainless ISO36U/S 762 mm Double Oven – Unframed Classic Stainless IDO30U/S ACCESSORIES Built-In Ovens Bake stone accessory, includes stone, rack and peel Additional oven racks Two-piece broiler pan and temperature probe Dehydration racks with door stop Accessories are available through your Wolf dealer. 5 B U I LT- I N O V E N S OVERALL DIMENSIONS 762 mm Built-In Single Oven MODEL OPTIONS Unframed / Classic 32 mm TOP VIEW RIGHT SIDE VIEW 762 mm Built-In Single Oven 48 mm CONDUIT CHANNEL ISO30U/S 662 mm 699 mm 610 mm INSIDE SIDE TRIM S P E C I F I C AT I O N S 716 mm 48 mm 762 mm Built-In Single Oven 759 mm Overall Dimensions (W x H x D) 759 mm x 699 mm x 610 mm Door Clearance 527 mm Overall Oven Interior Capacity 127 L Overall Interior Dim (W x H x D) 635 mm x 419 mm x 483 mm Usable Interior Dim (W x H x D) 546 mm x 419 mm x 416 mm Cabinet Width 838 mm rec 762 mm min Cabinet Depth 610 mm min Min Base Support 113 kg Opening Width 724 mm Opening Height 691 mm Trim Overlaps 5 mm top 3 mm bottom 19 mm each side Electrical Supply 1.2 m flexible 4-wire Electrical Rating 5.1 kW at 240 V Total Amps 21 Shipping Weight 124 kg 610 mm BEHIND FRAME OPEN OVEN DOOR Unit dimensions may vary to ± 3 mm. 527 mm 711 mm I N S TA L L AT I O N S P E C I F I C AT I O N S 762 mm Built-In Single Oven Wall Application 838 mm RECOMMENDED CABINET WIDTH 762 mm min 610 mm min OPENING DEPTH 220-240 V AC, 50/60 Hz 30 amp dedicated circuit Conduit 76 mm E 724 mm 691 mm OPENING HEIGHT OPENING WIDTH ELECTRICAL LOCATION WITHIN OPENING APPLIES ONLY TO CABINETS DEEPER 127 THAN 610 mm mm 102 mm E E E I N S TA L L AT I O N O P T I O N S The Wolf 762 mm single oven may be installed below a Wolf 762 mm electric or gas cooktop. Unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven within reach of the conduit. The Wolf 762 mm single oven may also be installed below a Wolf 914 mm electric or gas cooktop. Undercounter Installation 838 mm RECOMMENDED CABINET WIDTH 762 mm min The Wolf 762 mm single oven may be installed in combination with a Wolf warming drawer. A Wolf 762 mm single oven may be installed next to another 762 mm single oven. You must allow for a 64 mm space between the oven rough openings. Also, a separate inner wall is required for each oven between openings. Refer to installation instructions shipped with each Wolf product for detailed specifications. 6 95 mm min 691 mm OPENING HEIGHT 127 ELECTRICAL LOCATION WITHIN mm OPENING APPLIES ONLY TO CABINETS DEEPER THAN 610 mm E E 102 mm 914 mm 610 mm min OPENING DEPTH STANDARD FLOOR TO COUNTER HEIGHT 724 mm OPENING WIDTH 121 mm min IMPORTANT NOTE: Unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in an adjacent cabinet within reach of the conduit. Choose the location shown in the illustrations that best suits your installation. B U I LT- I N O V E N S OVERALL DIMENSIONS 914 mm Built-In Single Oven RIGHT SIDE VIEW 32 mm TOP VIEW MODEL OPTIONS 914 mm Built-In Single Oven 48 mm CONDUIT CHANNEL 619 mm Unframed / Classic 584 mm ISO36U/S 610 mm INSIDE SIDE TRIM 48 mm 867 mm S P E C I F I C AT I O N S 914 mm Built-In Single Oven 905 mm 76 mm 610 mm BEHIND FRAME OPEN OVEN DOOR Unit dimensions may vary to ± 3 mm. 870 mm I N S TA L L AT I O N S P E C I F I C AT I O N S 914 mm Built-In Single Oven Wall Application 991 mm RECOMMENDED CABINET WIDTH 914 mm min E 451 mm Overall Dimensions (W x H x D) 905 mm x 619 mm x 610 mm Door Clearance 451 mm Overall Oven Interior Capacity 125 L Overall Interior Dim (W x H x D) 762 mm x 337 mm x 483 mm Usable Interior Dim (W x H x D) 673 mm x 337 mm x 416 mm Cabinet Width 991 mm rec 914 mm min Cabinet Depth 610 mm min Min Base Support 113 kg Opening Width 876 mm Opening Height 611 mm Trim Overlaps 5 mm top 3 mm bottom 19 mm each side Electrical Supply 220-240 V AC, 50/60 Hz 30 amp dedicated circuit Conduit .9 m flexible 4-wire Electrical Rating 5.1 kW at 240 V Total Amps 21 Shipping Weight 131 kg 876 mm 610 mm min OPENING DEPTH 611 mm OPENING HEIGHT OPENING WIDTH ELECTRICAL LOCATION WITHIN OPENING APPLIES ONLY TO CABINETS DEEPER THAN 610 mm 102 mm 127 E mm E E I N S TA L L AT I O N O P T I O N S Undercounter Installation 991 mm RECOMMENDED CABINET WIDTH 914 mm min 95 mm min 611 mm OPENING HEIGHT 610 mm min OPENING DEPTH ELECTRICAL LOCATION WITHIN OPENING APPLIES ONLY TO CABINETS DEEPER THAN 610 mm 914 mm STANDARD FLOOR TO COUNTER HEIGHT 127 mm E 102 mm E The Wolf 914 mm single oven may be installed below a Wolf 914 mm electric or gas cooktop. Unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven within reach of the conduit. The 914 mm single oven may also be installed below a Wolf 762 mm framed electric cooktop, but not below a 762 mm unframed electric cooktop or 762 mm gas cooktop. When installed below a cooktop, it is recommended that the opening for the oven be 197 mm from the floor to ease the use of the oven door. The Wolf 914 mm single oven may be installed above or below a Wolf warming drawer with integrated drawer front. 876 mm OPENING WIDTH 197 mm rec 121 mm min IMPORTANT NOTE: Unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in an adjacent cabinet within reach of the conduit. Choose the location shown in the illustrations that best suits your installation. A Wolf 914 mm single oven may be installed directly above another 914 mm oven. You must allow enough space between the oven rough openings to accommodate a base support for the top oven. A 914 mm single oven may be installed next to another 914 mm oven. You must allow for a 64 mm space between the oven rough openings. Also, a separate inner wall is required for each oven between openings. Each base cabinet support must be able to support 113 kg. 7 B U I LT- I N O V E N S OVERALL DIMENSIONS 762 mm Built-In Double Oven MODEL OPTIONS 32 mm TOP VIEW RIGHT SIDE VIEW 762 mm Built-In Double Oven 48 mm Unframed / Classic CONDUIT CHANNEL IDO30U/S 610 mm 48 mm S P E C I F I C AT I O N S 762 mm Built-In Double Oven Overall Width 759 mm Overall Height 1270 mm Overall Depth 610 mm Door Clearance 527 mm Overall Oven Interior Capacity (per oven) 127 L INSIDE SIDE TRIM OPEN OVEN DOOR 711 mm 759 mm 610 mm 76 mm BEHIND FRAME Overall Interior Dim (W x H x D) 635 mm x 419 mm x 483 mm each Usable Interior Dim (W x H x D) 546 mm x 419 mm x 416 mm each Cabinet Width 838 mm rec 762 mm min Cabinet Depth 610 mm min I N S TA L L AT I O N S P E C I F I C AT I O N S Min Base Support 181 kg Opening Width 724 mm 762 mm Built-In Double Oven Wall Application Opening Height 1260 mm Trim Overlaps 5 mm top 3 mm bottom 19 mm each side Electrical Supply 220-240 V AC, 50/60 Hz 50 amp dedicated circuit Conduit 1.5 m flexible 4-wire Electrical Rating 8.9 kW at 240 V Total Amps 37 Shipping Weight 211 kg I N S TA L L AT I O N Refer to installation instructions shipped with each Wolf product for detailed specifications. 716 mm 1232 mm 1270 mm Unit dimensions may vary to ± 3 mm. 838 mm RECOMMENDED CABINET WIDTH 762 mm min 610 mm min OPENING DEPTH E 724 mm 1260 mm OPENING WIDTH OPENING HEIGHT 1702 mm typical ELECTRICAL LOCATION WITHIN OPENING APPLIES ONLY TO CABINETS DEEPER 127 THAN 610 mm mm 102 mm E E IMPORTANT NOTE: Unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in an adjacent cabinet within reach of the conduit. Choose the location shown in the illustrations that best suits your installation. 8 E 527 mm WOLF ELECTRIC COOKTOPS WOLF FRAMED ELECTRIC COOKTOPS FEATURES Behind the sophisticated, minimalist exterior, beneath that perfectly smooth, subtly patterned glass that cleverly reduces scratches, there is a high-performance cooking tool. Classic stainless steel trim finish The black ceramic glass top is beautifully complemented by the classic stainless steel trim. Multiple cooking elements with different zones allow your customer a variety of different applications. The 914 mm cooktop features a 305 mm diameter triple heating element—concentric rings that give you exceptional control of temperature for pans and pots of every size. All of the heating elements offer True Simmer, and with each cooktop there is one element that enables you to set a temperature for melting. Easy-to-clean black ceramic glass surface is resistant to scratching, staining, impact and heat—translucent surface allows you to see the glow of hot elements Illuminated electronic touch controls with graduated control lighting Model ICT15E/S 381 mm Framed Electric Cooktop Ribbon-type radiant heating elements—some elements with multiple temperature zones True Simmer setting on all elements Melt setting on one element Hot surface indicators on all elements High frequency pulsation elements improve cooking performance and control Model ICT30E/S 762 mm Framed Electric Cooktop Temperature limiter to ensure that safe operating temperature of ceramic glass is never exceeded Child safety lock key and universal off Model ICT36E/S 914 mm Framed Electric Cooktop This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. F R A M E D E L E C T R I C C O O K T O P F E AT U R E S Model ICT36E/S shown Triple-zone element Illuminated electronic touch controls Dual-zone element OFF SIM SIM MODEL OPTIONS H HIG ON E2 3 ZON E ZON OFF O H HIG OFF ON SIM Framed Electric Cooktops H HIG H HIG OFF ON OFF ON E2 ZON SIM H HIG ON OFF MELT 381 mm Framed Electric Cooktop Lock key and universal off Classic Trim ICT15E/S 762 mm Framed Electric Cooktop True Simmer on all elements Classic Trim 914 mm Framed Electric Cooktop Classic Trim Framed edge ICT30E/S ICT36E/S Location of rating plate Hot surface indicators 9 WOLF ELECTRIC COOKTOPS ACCESSORIES Optional accessories are available through your Wolf dealer. PLANNING INFORMATION ELECTRICAL REQUIREMENTS From a planning perspective, your selection process is made easier by the three different sizes you have to choose from. For ease of installation, Wolf recommends using 838 mm cabinets with the 762 mm cooktop and 991 mm cabinets with the 914 mm cooktop. Electric cooktops require a separate, grounded 220-240 V AC, 50/60 Hz electrical supply with its own circuit breaker. Locate electrical supply within the shaded area shown in the Installation Specifications illustration for your model. Specifications on the following pages provide overall dimensions, countertop cut-out dimensions and installation specifics for the three different-sized cooktops. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation. A Wolf single built-in oven may be installed below these cooktops. Wolf framed electric cooktops are designed and agency approved for installation with Wolf built-in ovens only. Also, be aware of the depth of the cooktop when planning for this installation. IMPORTANT NOTE: When an oven is installed below the cooktop, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven, unless you are using cabinets deeper than 610 mm. Refer to pages 6–7 for additional specifications for built-in ovens. You must follow all local codes and ordinances when installing your service. These cooktops are intended for indoor use. Multiple cooktops and/or integrated modules can be installed side by side. Refer to the countertop cut-out dimensions on page 19 when planning for this installation. These cooktops can accommodate a Wolf cooktop hood or downdraft system. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications. ACCESSORIES Electric Cooktops Filler strip Bracket supports for installation of two integrated modules with downdraft (Model DD30 only) Accessories are available through your Wolf dealer. 10 This appliance must be installed in accordance with local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit that is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency and amperage ratings are listed on the product rating plate. WOLF ELECTRIC COOKTOPS OVERALL DIMENSIONS Model ICT15E/S MODEL OPTIONS 381 mm Framed Electric Cooktop Classic Trim Finish 533 mm ICT15E/S OVERALL DEPTH S P E C I F I C AT I O N S 381 mm Framed Electric Cooktop 381 mm OVERALL WIDTH 89 mm Overall Width 381 mm Overall Height 89 mm Overall Depth 533 mm Heating Elements Two Temperature Zones Three Max Element Power 750 W / 2200 W (dual) Unit dimensions may vary to ± 3 mm. Max Element Power 1200 W (single) Cabinet Depth 578 mm min I N S TA L L AT I O N S P E C I F I C AT I O N S Height Clearance 102 mm min Model ICT15E/S Cut-Out Width* 340 mm Cut-Out Depth 489 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Conduit 1.2 m flexible 3-wire Electrical Rating 3.4 kW at 240 V Shipping Weight 14 kg 838 mm RECOMMENDED 330 mm max CABINET WIDTH 457 mm 51** 489 mm mm COOKTOP CUT-OUT DEPTH 64 mm min 51 mm min* 762 mm COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 340 mm CUT-OUT TO COMBUSTIBLE COOKTOP CUT-OUT WIDTH MATERIALS (BOTH SIDES) 102 mm E 914 mm STANDARD FLOOR TO COUNTERTOP HEIGHT 381 mm 381 mm *If the 381 mm cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width increases to 356 mm. The outer diameter of the heating elements are 229 mm and 165 mm. I N S TA L L AT I O N Refer to installation instructions shipped with each Wolf product for detailed specifications. NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. 340 mm Countertop Cut-Out Dimensions COOKTOP CUT-OUT WIDTH 489 mm 64 mm min COOKTOP CUT-OUT DEPTH FRONT OF COUNTERTOP 11 WOLF ELECTRIC COOKTOPS OVERALL DIMENSIONS 762 mm Framed Electric Cooktop MODEL OPTIONS 762 mm Framed Electric Cooktop Classic Trim Finish ICT30E/S 533 mm OVERALL DEPTH S P E C I F I C AT I O N S 762 mm Framed Electric Cooktop Overall Width 762 mm Overall Height 89 mm Overall Depth 533 mm Heating Elements Four Temperature Zones Six 762 mm OVERALL WIDTH 89 mm Max Element Power 750 W / 2200 W and (two dual) 950 W / 1900 W Max Element Power 1200 W and 1500 W (two single) Unit dimensions may vary to ± 3 mm. Cabinet Width 838 mm rec 762 mm min I N S TA L L AT I O N S P E C I F I C AT I O N S Cabinet Depth 578 mm min 762 mm Framed Electric Cooktop Height Clearance 102 mm min Cut-Out Width* 721 mm Cut-Out Depth 489 mm Electrical Supply 220-240 V AC, 50/60 Hz 40 amp dedicated circuit Conduit 1.2 m flexible 3-wire Electrical Rating 6.8 kW at 240 V Shipping Weight 20 kg *If the 762 mm cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width increases to 737 mm. 838 mm RECOMMENDED 330 mm max 51** 457 mm 489 mm mm COOKTOP CUT-OUT DEPTH 64 mm min 51 mm min* CUT-OUT TO COMBUSTIBLE MATERIALS (BOTH SIDES) The outer diameter of the heating elements are 229 mm, 216 mm, 179 mm and 165 mm. A Wolf 762 mm single oven may be installed below the Wolf 762 mm framed electric cooktop. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. A Wolf 914 mm single oven may also be installed below the Wolf 762 mm framed electric cooktop. Refer to pages 6 and 7 for additional specifications. 762 mm 762 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 721 mm COOKTOP CUT-OUT WIDTH 102 mm E 89 mm 610 mm min I N S TA L L AT I O N O P T I O N S CABINET WIDTH 95 mm min 914 mm STANDARD FLOOR TO COUNTERTOP HEIGHT 254 mm 762 mm OVEN OPENING *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. 721 mm Countertop Cut-Out Dimensions COOKTOP CUT-OUT WIDTH Refer to installation instructions shipped with each Wolf product for detailed specifications. 489 mm COOKTOP CUT-OUT DEPTH 64 mm min FRONT OF COUNTERTOP 12 WOLF ELECTRIC COOKTOPS OVERALL DIMENSIONS 914 mm Framed Electric Cooktop MODEL OPTIONS 914 mm Framed Electric Cooktop Classic Trim Finish 533 mm ICT36E/S OVERALL DEPTH S P E C I F I C AT I O N S 914 mm Framed Electric Cooktop 914 mm OVERALL WIDTH 89 mm Overall Width 914 mm Overall Height 89 mm Overall Depth 533 mm Heating Elements Five Temperature Zones Eight Max Element Power 1050 W / 2200 W / (triple) 2700 W Unit dimensions may vary to ± 3 mm. Max Element Power 750 W / 2200 W (dual) Max Element Power 1200 W, 1500 W (three single) and 1800 W I N S TA L L AT I O N S P E C I F I C AT I O N S 914 mm Framed Electric Cooktop 991 mm 330 mm max 51** 457 mm 489 mm mm COOKTOP CUT-OUT DEPTH 64 mm min 51 mm min* CUT-OUT TO COMBUSTIBLE MATERIALS (BOTH SIDES) RECOMMENDED CABINET WIDTH 762 mm 914 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 873 mm COOKTOP CUT-OUT WIDTH 102 mm 89 mm 610 mm min 95 mm min 914 mm STANDARD FLOOR TO COUNTERTOP HEIGHT Cabinet Width 991 mm rec 914 mm min Cabinet Depth 578 mm min Height Clearance 102 mm min Cut-Out Width* 873 mm Cut-Out Depth 489 mm Electrical Supply 220-240 V AC, 50/60 Hz 50 amp dedicated circuit Conduit 1.2 m flexible 3-wire Electrical Rating 9.4 kW at 240 V Shipping Weight 27 kg *If the 914 mm cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width increases to 889 mm. E The outer diameter of the heating elements are 302 mm, 232 mm, 200 mm, 181 mm and 165 mm. 254 mm 914 mm OVEN OPENING I N S TA L L AT I O N O P T I O N S A Wolf 914 mm single oven may be installed below the Wolf 914 mm framed electric cooktop. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. A Wolf 762 mm single oven may also be installed below the Wolf 914 mm framed electric cooktop. Refer to pages 6 and 7 for additional specifications. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. 873 mm Countertop Cut-Out Dimensions COOKTOP CUT-OUT WIDTH 489 mm COOKTOP CUT-OUT DEPTH 64 mm min When a 914 mm oven is installed below a cooktop, it is recommended that the rough opening for the oven be 197 mm from the floor to ease the use of the oven door. FRONT OF COUNTERTOP 13 WOLF GAS COOKTOPS Model ICBCT15G/S 381 mm Gas Cooktop Model ICBCT30G/S 762 mm Gas Cooktop WOLF GAS COOKTOPS FEATURES New features make cooking a greater pleasure than ever. For instance, at higher settings the dual-stacked burner design uses its upper-level burner for maximum heat transfer. Merely turn down the illuminated knob and the lower-tier burners deliver fine-tuning control and True Simmer. You’ll see why we patented this concept when you can have the slightest of flame and enjoy a simmer with no boiling or scorching. This is heat tailored for every cooking vessel you’re using—from the largest stockpot to the smallest melting pan. Available in natural and LP gas A more powerful 5.0 kW burner is standard on the 762 mm and 914 mm gas cooktops. The dual-stacked sealed burners and deep recess of the seamless drawn pan area make cleanup of any of those previously unsightly spills a snap. Stainless steel top construction, available in classic stainless steel finish Dual-stacked, sealed burners with automatic reignition on all settings Large 5.0 kW burner with .2 kW delivered at simmer—Models ICBCT30G/S and ICBCT36G/S only Medium 4.0 kW burner with .2 kW delivered at simmer Small 3.2 kW burners with .1 kW delivered at simmer Electronic spark ignition system True Simmer setting on all burners Illuminated control panel with two-tiered control knobs Low-profile, cast iron continuous burner grates with matte porcelain finish Seamless drawn burner pan Model ICBCT36G/S 914 mm Gas Cooktop CE certified This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. G A S C O O K T O P F E AT U R E S Model ICBCT36G/S shown Small 3.2 kW burners Low-profile continuous grates Two-tiered control knobs MODEL OPTIONS Gas Cooktops 381 mm Gas Cooktop Illuminated control panel Classic Stainless 762 mm Gas Cooktop Classic Stainless Medium 4.0 kW burner Large 5.0 kW burner 14 ICBCT30G/S 914 mm Gas Cooktop Classic Stainless Location of rating plate Seamless drawn pan ICBCT15G/S ICBCT36G/S WOLF GAS COOKTOPS PLANNING INFORMATION ELECTRICAL | GAS REQUIREMENTS Wolf recommends using 838 mm cabinets with the 762 mm cooktop and 991 mm cabinets with the 914 mm cooktop. IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. Specifications on the following pages provide overall dimensions, countertop cut-out dimensions and installation specifics for the three different-sized cooktops. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation. Wolf gas cooktops are designed to operate on natural gas, I2H, I2E, and I2E+ at 20 mb pressure or LP (propane) gas at 37 mb WC pressure. They are supplied with an ISO 14 male gas connection at the right rear corner on the bottom of the cooktop. The male connector exits the unit straight down. A Wolf single built-in oven may be installed below these cooktops. Wolf gas cooktops are designed and agency approved for installation with Wolf built-in ovens only. Also, be aware of the depth of the cooktop when planning for this installation. Locate electrical and gas supply within the shaded area shown in the Installation Specifications illustration for your model. Multiple cooktops and/or integrated modules can be installed side by side. Refer to the countertop cut-out dimensions on page 19 when planning for this installation. These cooktops can accommodate a Wolf cooktop hood or downdraft system. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications. IMPORTANT NOTE: When an oven is installed below the cooktop, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven, unless you are using cabinets deeper than 610 mm. Refer to pages 6–7 for additional specifications for built-in ovens. When a gas cooktop is installed above cabinets, the gas and electrical placement is not critical. A grounded outlet needs to be placed within 1.2 m of the right rear of the cooktop. You must follow all local codes and ordinances when installing your services. These cooktops are intended for indoor use. ACCESSORIES Gas Cooktops One-piece wok and single burner grate (Models ICBCT30G/S and ICBCT36G/S) Filler strip Bracket supports for installation of two integrated modules with downdraft (Model DD30 only) Accessories are available through your Wolf dealer. 15 WOLF GAS COOKTOPS OVERALL DIMENSIONS 381 mm Gas Cooktop MODEL OPTIONS 381 mm Gas Cooktop Classic / Natural Gas ICBCT15G/S 533 mm Classic / LP Gas OVERALL DEPTH ICBCT15G/S-LP S P E C I F I C AT I O N S 381 mm Gas Cooktop 381 mm OVERALL WIDTH Overall Width 381 mm Overall Height 102 mm Overall Depth 533 mm Burner Rating (1) 4.0 kW with .2 kW delivered at simmer (1) 3.2 kW with .1 kW delivered at simmer 102 mm Unit dimensions may vary to ± 3 mm. Cabinet Depth 578 mm min Height Clearance 102 mm min Cut-Out Width 356 mm I N S TA L L AT I O N S P E C I F I C AT I O N S Cut-Out Depth 489 mm 381 mm Gas Cooktop Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Gas Rating 7.2 kW Shipping Weight 14 kg Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N O P T I O N S 838 mm RECOMMENDED 330 mm max For the 381 mm gas cooktop, the gas service may be supplied through the floor if the cooktop is not installed above an oven. Refer to the illustration for specifics on placement of gas and electrical. 64** mm CABINET WIDTH 457 mm 489 mm COOKTOP CUT-OUT DEPTH 64 mm min 178 mm min* 762 mm COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 356 mm CUT-OUT TO COMBUSTIBLE COOKTOP CUT-OUT WIDTH MATERIALS (BOTH SIDES) 102 mm Refer to installation instructions shipped with each Wolf product for detailed specifications. E 914 mm LOCATION OF GAS SUPPLY MAY ALSO EXTEND 127 mm ON FLOOR FROM BACK WALL STANDARD FLOOR TO COUNTERTOP HEIGHT G 381 mm 381 mm LOCATION OF GAS SUPPLY MAY ALSO EXTEND 127 mm ON FLOOR FROM BACK WALL 127 mm 381 mm NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 33" (838) recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. 356 mm Countertop Cut-Out Dimensions COOKTOP CUT-OUT WIDTH 489 mm 64 mm min COOKTOP CUT-OUT DEPTH FRONT OF COUNTERTOP 16 WOLF GAS COOKTOPS OVERALL DIMENSIONS 762 mm Gas Cooktop MODEL OPTIONS 762 mm Gas Cooktop 533 mm Classic / Natural Gas ICBCT30G/S OVERALL DEPTH Classic / LP Gas ICBCT30G/S-LP S P E C I F I C AT I O N S 762 mm Gas Cooktop 762 mm OVERALL WIDTH 102 mm Overall Width 762 mm Overall Height 102 mm Overall Depth 533 mm Burner Rating (1) 5.0 kW with .2 kW delivered at simmer (1) 4.0 kW with .2 kW delivered at simmer Unit dimensions may vary to ± 3 mm. (2) 3.2 kW with .1 kW delivered at simmer I N S TA L L AT I O N S P E C I F I C AT I O N S 762 mm Gas Cooktop 838 mm RECOMMENDED 330 mm max 64** mm 457 mm 489 mm COOKTOP CUT-OUT DEPTH 610 mm min 64 mm min 229 mm min* CUT-OUT TO COMBUSTIBLE MATERIALS (BOTH SIDES) CABINET WIDTH 762 mm 762 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 737 mm COOKTOP CUT-OUT WIDTH 102 mm 89 mm 95 mm min 914 mm STANDARD FLOOR TO COUNTERTOP HEIGHT E Cabinet Width 838 mm rec 762 mm min Cabinet Depth 578 mm min Height Clearance 102 mm min Cut-Out Width 737 mm Cut-Out Depth 489 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Gas Rating 15.4 kW Shipping Weight 23 kg Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N O P T I O N S A Wolf 762 mm single oven may be installed below the Wolf 762 mm gas cooktop. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical and gas supply be placed in the base cabinet to the right of the oven. Refer to page 6 for additional specifications. G 254 mm 762 mm OVEN OPENING *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. 737 mm Countertop Cut-Out Dimensions COOKTOP CUT-OUT WIDTH 489 mm COOKTOP CUT-OUT DEPTH 64 mm min FRONT OF COUNTERTOP 17 WOLF GAS COOKTOPS OVERALL DIMENSIONS 914 mm Gas Cooktop MODEL OPTIONS 914 mm Gas Cooktop Classic / Natural Gas ICBCT36G/S 533 mm Classic / LP Gas OVERALL DEPTH ICBCT36G/S-LP S P E C I F I C AT I O N S 914 mm Gas Cooktop 914 mm Overall Width 914 mm Overall Height 102 mm Overall Depth 533 mm Burner Rating (1) 5.0 kW with .2 kW delivered at simmer (1) 4.0 kW with .2 kW delivered at simmer OVERALL WIDTH 102 mm Unit dimensions may vary to ± 3 mm. (3) 3.2 kW with .1 kW delivered at simmer Cabinet Width 991 mm rec 914 mm min Cabinet Depth 578 mm min Height Clearance 102 mm min Cut-Out Width 889 mm Cut-Out Depth 489 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Gas Rating 18.6 kW Shipping Weight 30 kg I N S TA L L AT I O N O P T I O N S I N S TA L L AT I O N S P E C I F I C AT I O N S 914 mm Gas Cooktop 64** mm A Wolf 914 mm single oven may be installed below the Wolf 914 mm gas cooktop. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical and gas supply be placed in the base cabinet to the right of the oven. A Wolf 762 mm single oven may also be installed below the Wolf 914 mm gas cooktop. Refer to pages 6 and 7 for additional specifications. 991 mm 330 mm max 457 mm 489 mm COOKTOP CUT-OUT DEPTH 64 mm min 229 mm min* CUT-OUT TO COMBUSTIBLE MATERIALS (BOTH SIDES) RECOMMENDED CABINET WIDTH 762 mm 914 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 889 mm COOKTOP CUT-OUT WIDTH 102 mm 89 mm 610 mm min 95 mm min 914 mm STANDARD FLOOR TO COUNTERTOP HEIGHT E G 254 mm 914 mm OVEN OPENING When a 914 mm oven is installed below a cooktop, it is recommended that the rough opening for the oven be 197 mm from the floor to ease the use of the oven door. Refer to installation instructions shipped with each Wolf product for detailed specifications. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. 889 mm Countertop Cut-Out Dimensions COOKTOP CUT-OUT WIDTH 489 mm COOKTOP CUT-OUT DEPTH 64 mm min FRONT OF COUNTERTOP 18 WOLF INTEGRATED MODULES WOLF INTEGRATED MODULES With Wolf‘s integrated modules, you have the ultimate in customization. You can create your own design by mixing and matching the various components within this system. And when you couple these modules with other cooktops within the Wolf inventory, you and your client will truly understand freedom of choice. IMPORTANT NOTE: Refer to specifications on the following pages for specific installation requirements and limitations for each integrated module. Review specific installation instructions for product-to-product capabilities. Additional information is provided in the specifications pdf files on our website, wolfappliance.com Some modules integrate with their larger counterparts, right down to their low-profile grates, dual-stacked gas burners, deep spill pan and illuminated controls. The two-element electric and dual-stacked sealed burner gas cooktop modules deliver the same performance and appearance as the larger electric and gas cooktops. Refer to the following illustration for countertop cut-out dimensions for the installation of multiple cooktops or modules. Some integrated modules can be installed together or with a 762 mm or 914 mm cooktop. When multiple cooktops or modules are installed side by side, the cut-out dimensions shown in the illustration below are derived by adding 32 mm additional space for each additional unit, to give you your total cut-out width. IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, each unit must have its own separate recommended electrical circuit. When multiple gas cooktops or modules are installed next to one another, they can receive their gas supply from a common line. However, each unit must have its own regulator installed between the mainline and the cooktop or module. Model CT15I/S Induction Cooktop Model ICT15E/S Electric Cooktop Model ICBIG15/S Electric Grill These integrated modules are intended for indoor use. Model ICBIS15/S Electric Steamer C O U N T E R T O P C U T- O U T D I M E N S I O N S Installation of Multiple Cooktops or Modules 1518 mm – FOUR MODULES WIDTH OR 1511 mm – 762 mm COOKTOP AND TWO MODULES OR 1276 mm – 914 mm COOKTOP AND ONE MODULE 1130 mm – THREE MODULES WIDTH OR 1124 mm – 762 mm COOKTOP AND ONE MODULE 743 mm Model ICBIF15/S Electric Fryer I N T E G R AT E D M O D U L E S 381 mm Width TWO MODULES WIDTH 356 mm 64 mm min CUT-OUT WIDTH 489 mm CUT-OUT DEPTH Induction Cooktop CT15I/S Electric Cooktop ICT15E/S Electric Grill ICBIG15/S Electric Steamer ICBIS15/S Electric Fryer ICBIF15/S Gas Cooktop ICBCT15G/S Gas Multi-Function Cooktop IIM15/S Model ICBCT15G/S Gas Cooktop FRONT OF COUNTERTOP All integrated modules are available in the classic stainless steel finish. IMPORTANT NOTE: When two or more modules are installed together, an integrated module filler strip is recommended. If a Model DD30 downdraft system is also installed, an integrated module support for downdraft ventilation is required. Contact your Wolf dealer for information on these accessory components. IMPORTANT NOTE: Refer to specifications on the following pages for specific installation requirements and limitations for each integrated module. Specifications for Model ICT15E/S are found on page 11 and Model ICBCT15G/S specifications are on page 16. Model IIM15/S Gas Multi-Function Cooktop 19 WOLF INTEGRATED MODULES Model CT15I/S Induction Cooktop INDUCTION COOKTOP FEATURES While induction cooking is new to North America, it has been used in Europe for decades by professionals and homeowners demanding the best in performance. Integrated design allows for installation of multiple cooktops or modules Cooking with this sleek 15-inch powerhouse is simply the best way to cook. Electricity flows through a coil to produce a magnetic field under the sleek black ceramic top. When an iron or magnetic stainless steel pan is placed on the surface, the magnetic field creates a current in the pan, exciting the molecules and heating the pan and not the cooktop. That‘s why the cooktop stays cool to the touch and the food cooks efficiently. In fact, this unit is so efficient that it outperforms gas and electric cooktops. There is no wasted heat because energy is supplied directly to the cooking vessel, so nearly 90 percent of the energy gets used to cook. You can keep sauces and chocolates melted at 50 watts of power, or with the touch of a finger, activate the hi-power boost feature and boil water in nearly half the time you normally do. Classic stainless steel trim finish Easy-to-clean black ceramic glass surface is resistant to scratching, staining, impact and heat Induction elements heat cookware not the glass, for a cooler and safer cooking surface Cookware sensing—elements will not be energized without an iron or magnetic stainless steel pan on the cooktop surface Illuminated electronic touch controls with graduated control lighting High-efficiency elements deliver power and control Hi-Power mode boosts power on rear element to 2200 W maximum power output by diverting power from front element Simultaneous operation of both elements at 1800 W each True Simmer setting on both elements Melt setting on both elements Temperature limiter to ensure that safe operating temperature of ceramic glass is never exceeded The Wolf induction cooktop has it all. Child safety lock key and universal off I N D U C T I O N C O O K T O P F E AT U R E S OVERALL DIMENSIONS Model CT15I/S Model CT15I/S Two induction elements Illuminated electronic touch controls 533 mm OVERALL DEPTH Lock key and universal off H HIG LT ME ON OFF WER HI-PO HIGH ON OFF SIM O OFF 381 mm OVERALL WIDTH 64 mm Classic stainless steel trim finish True Simmer and melt on both elements Location of rating plate ACCESSORIES Induction Cooktop Filler strip Bracket supports for installation of two integrated modules with 762 mm downdraft Accessories are available through your Wolf dealer. 20 WOLF INTEGRATED MODULES PLANNING INFORMATION ELECTRICAL REQUIREMENTS The illustrations provide the overall dimensions and finished cut-out dimensions that you need to plan for in your installation. We have minimized the information contained in the illustrations, concentrating on the critical information you must plan into your installation. The Wolf induction cooktop requires a separate, grounded 3-wire 220-240 V AC, 50/60 Hz, 20 amp service with its own circuit breaker. Locate electrical within the shaded area shown in the illustration. You must follow all local codes and ordinances when installing your service. IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, refer to page 19 for countertop cut-out dimensions. I N S TA L L AT I O N The induction cooktop can accommodate a Wolf cooktop hood or downdraft system. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications. Refer to installation instructions shipped with each Wolf product for detailed specifications. I N S TA L L AT I O N S P E C I F I C AT I O N S S P E C I F I C AT I O N S Model CT15I/S Model CT15I/S Induction Cooktop 838 mm RECOMMENDED 330 mm max 51** CABINET WIDTH 457 mm 489 mm mm COOKTOP CUT-OUT DEPTH 64 mm min 51 mm min* 762 mm COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 340 mm CUT-OUT TO COMBUSTIBLE COOKTOP CUT-OUT WIDTH MATERIALS (BOTH SIDES) 114 mm E 914 mm STANDARD FLOOR TO COUNTERTOP HEIGHT 381 mm 381 mm NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. Trim Finish Classic Overall Width 381 mm Overall Height 64 mm Overall Depth 533 mm Induction Elements Two Max Element Power 1800 W (front) Max Element Power 2200 W (rear) Cabinet Depth 578 mm min Height Clearance 152 mm min Cut-Out Width* 340 mm Cut-Out Depth 489 mm Electrical Supply 220-240 V AC, 50/60 Hz 20 amp dedicated circuit Conduit 1.2 m flexible 3-wire Electrical Rating 3.4 kW Shipping Weight 14 kg *If the induction cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width increases to 356 mm. 340 mm Countertop Cut-Out Dimensions COOKTOP CUT-OUT WIDTH 489 mm 64 mm min COOKTOP CUT-OUT DEPTH IMPORTANT NOTE: A minimum height clearance of 152 mm is required. If a shelf is installed below the unit, a 25 mm gap at the rear of the cabinet shelf is necessary to allow for proper ventilation. Failure to do so could result in decreased performance or product damage. Unit dimensions may vary to ± 3 mm. FRONT OF COUNTERTOP 21 WOLF INTEGRATED MODULES Model ICBIG15/S Electric Grill Module ELECTRIC GRILL MODULE FEATURES Who says you have to sacrifice the fun of grilling when the weather changes and you cannot take advantage of the outdoors? With this grill cooktop you can easily handle steaks and all sorts of food without the hassle of lava rocks or briquettes. Integrated design allows for installation of multiple cooktops or modules There are two individual heating elements—front and back—on this module that enable you to cook on one side while keeping other items at serving temperature. For ease of cleaning, there are porcelainized plates below two 1400-watt heating elements that accumulate any unwanted grease and drain it away. The Wolf electric grill module is available in classic stainless steel. Stainless steel top construction with classic stainless steel finish Two 1400-watt, individually controlled heating elements—front and back—for even grilling Illuminated electronic touch controls with graduated control lighting Low-profile, one-piece cast iron grilling grate with matte porcelain finish Black porcelain-coated grease deflection plates Easy-to-clean, removable porcelain collection pan Independent digital timer CE certified This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. E L E C T R I C G R I L L F E AT U R E S OVERALL DIMENSIONS Model ICBIG15/S Model ICBIG15/S Low-profile, one-piece grilling grate Two 1400-watt heating elements 533 mm OVERALL DEPTH Illuminated electronic touch controls 381 mm OVERALL WIDTH 159 mm Removable collection pan Graduated control lighting Location of rating plate ACCESSORIES Electric Grill Module Filler strip Accessories are available through your Wolf dealer. 22 WOLF INTEGRATED MODULES PLANNING INFORMATION ELECTRICAL REQUIREMENTS The illustrations provide the overall dimensions and finished cut-out dimensions that you need to plan for in your installation. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation. The Wolf International electric grill module is CB approved and and is manufactured for a 220-240 V AC, 50/60 Hz electrical supply. Locate electrical within the shaded area shown in the illustration. You must follow all local codes and ordinances when installing your service. IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, refer to page 19 for countertop cut-out dimensions. I N S TA L L AT I O N The grill module can accommodate a Wolf cooktop hood. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications. Refer to installation instructions shipped with each Wolf product for detailed specifications. IMPORTANT NOTE: Wolf does not recommend the use of downdraft ventilation with the grill module. I N S TA L L AT I O N S P E C I F I C AT I O N S S P E C I F I C AT I O N S Model ICBIG15/S Model ICBIG15/S Electric Grill Module 838 mm RECOMMENDED 330 mm max 51** CABINET WIDTH 457 mm 489 mm mm COOKTOP CUT-OUT DEPTH 64 mm min 178 mm min* 762 mm COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 356 mm CUT-OUT TO COMBUSTIBLE COOKTOP CUT-OUT WIDTH MATERIALS (BOTH SIDES) 159 mm 914 mm E STANDARD FLOOR TO COUNTERTOP HEIGHT 381 mm Exterior Finish Classic Overall Width 381 mm Overall Height 159 mm Overall Depth 533 mm Temperature Zones Two Heating Element Zone (front) 1400 W Heating Element Zone (rear) 1400 W Total Element Power 2800 W Cabinet Depth 578 mm min Height Clearance 159 mm min Cut-Out Width 356 mm Cut-Out Depth 489 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Electrical Rating 2.8 kW Shipping Weight 28 kg 381 mm Unit dimensions may vary to ± 3 mm. NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. 356 mm Countertop Cut-Out Dimensions COOKTOP CUT-OUT WIDTH 489 mm 64 mm min COOKTOP CUT-OUT DEPTH FRONT OF COUNTERTOP 23 WOLF INTEGRATED MODULES Model ICBIS15/S Electric Steamer Module ELECTRIC STEAMER MODULE FEATURES From a temperature of 60˚C to boil, you can keep food hot for long periods of time or defrost easily without drying out or losing flavor. Integrated design allows for installation of multiple cooktops or modules The beauty of this steamer module is accented by the sculptured glass domed lid, which is easily inverted for storage to keep a low profile. The deep, large vessel with a 7.6 L capacity can hold up to 3.3 L of cooked pasta. Includes one solid and one perforated stackable insert pan. The diversity of our electric steamer includes slow cooking, double boiling, steaming eggs, steaming custard, proofing bread dough, warming food and melting chocolate as well as steaming vegetables. The Wolf electric steamer module is available in classic stainless steel. Stainless steel top construction with classic stainless steel finish Hidden 2600-watt heating element Illuminated electronic touch controls with graduated control lighting Large 7.6 L maximum capacity tub—2.4 L capacity for steaming Two stackable stainless steel steamer insert pans—one solid and one perforated Uses include steaming vegetables, eggs and custard, double boiling, proofing bread dough, warming food and melting chocolate Can function as a slow cooker for 8–10 hours Reversible domed glass lid for easy storage Independent digital timer This steamer module must be installed at least 381 mm away from a Wolf fryer module, as contact between water and hot oil may cause burns from steam and hot oil. Digital temperature readout and preheat indicator Electronic drain CE certified This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. E L E C T R I C S T E A M E R F E AT U R E S OVERALL DIMENSIONS Model ICBIS15/S Model ICBIS15/S Reversible domed glass lid Hidden 2600-watt heating element 533 mm OVERALL DEPTH Illuminated electronic touch controls 381 mm OVERALL WIDTH Graduated control lighting Deep drawn pan 191 mm 343 mm TO DRAIN OUTLET Location of rating plate Digital temperature readout ACCESSORIES Electric Steamer Module Filler strip Accessories are available through your Wolf dealer. 24 WOLF INTEGRATED MODULES PLANNING INFORMATION The illustrations provide the overall dimensions and finished cut-out dimensions that you need to plan for in your installation. The steamer module can accommodate a Wolf cooktop hood. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications. IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, refer to page 19 for countertop cut-out dimensions. IMPORTANT NOTE: Wolf does not recommend the use of downdraft ventilation with the steamer module. For the drain connection, the 16 mm outlet from the valve will accept a drain hose that must flow downward to, and tie into, an existing sink drain. A separate drain with a freefall may also be installed. (Following local building codes, your plumber will dictate how to plumb the unit.) As a third option, the consumer will supply a heat resistant bucket for drainage in the location of the drain outlet. Refer to the illustration for location of the drain outlet. ELECTRICAL REQUIREMENTS The Wolf International electric steamer module is CB approved and and is manufactured for a 220-240 V AC, 50/60 Hz electrical supply. Locate electrical within the shaded area shown. I N S TA L L AT I O N Refer to installation instructions shipped with each Wolf product for detailed specifications. You must follow all local codes and ordinances when installing your service. I N S TA L L AT I O N S P E C I F I C AT I O N S S P E C I F I C AT I O N S Model ICBIS15/S Model ICBIS15/S Electric Steamer Module 838 mm RECOMMENDED 330 mm max 51** CABINET WIDTH 457 mm 489 mm mm COOKTOP CUT-OUT DEPTH 64 mm min 178 mm min* 343 mm 314 mm 194 mm DRAIN OUTLET LOCATION COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 356 mm CUT-OUT TO COMBUSTIBLE COOKTOP CUT-OUT WIDTH MATERIALS (BOTH SIDES) 314 mm 152 mm 914 mm STANDARD FLOOR TO COUNTERTOP HEIGHT E 762 mm DRAIN OUTLET LOCATION Exterior Finish Classic Overall Width 381 mm Overall Height 343 mm Overall Depth 533 mm Heating Element 2600 W Cabinet Depth 578 mm min Height Clearance 343 mm min Cut-Out Width 356 mm Cut-Out Depth 489 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Electrical Rating 2.6 kW Shipping Weight 18 kg Unit dimensions may vary to ± 3 mm. 381 mm 381 mm NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. 356 mm Countertop Cut-Out Dimensions COOKTOP CUT-OUT WIDTH This steamer module must be installed at least 381 mm away from a Wolf fryer module, as contact between water and hot oil may cause burns from steam and hot oil. 489 mm 64 mm min COOKTOP CUT-OUT DEPTH FRONT OF COUNTERTOP 25 WOLF INTEGRATED MODULES Model ICBIF15/S Electric Fryer Module ELECTRIC FRYER MODULE FEATURES To round out your options for the ideal kitchen, you can choose a fryer, and Wolf offers a great option that the market has never seen. When your clients use this module, they‘ll be able to create dinner specialties never tried before. Integrated design allows for installation of multiple cooktops or modules The accurate temperature control will enable your customer to seal in that great flavor of the food without absorbing any unnecessary grease. The fryer can handle a variety of foods at a wide range of oil temperatures. The Wolf fryer module is available in classic stainless steel. In addition, there is a metal storage lid to keep the grease area free from particles falling into the fryer. Stainless steel top construction with classic stainless steel finish Hidden 2600-watt heating element Illuminated electronic touch controls with graduated control lighting Large 3.8 L capacity tub Three baskets included—one large and two small side by side, each with wire basket hanger Low-profile lid Melt feature for shortening or lard Independent digital timer Digital temperature readout and preheat indicator This fryer module must be installed at least 381 mm away from any open flame cooking device. The open flame may cause ignition of oil. Easy manual locking drain capability Recommended for installation with any Wolf framed electric cooktop or the Wolf electric grill module CE certified This fryer module must be installed at least 381 mm away from a Wolf steamer module, as contact between water and hot oil may cause burns from steam and hot oil. E L E C T R I C F R Y E R F E AT U R E S OVERALL DIMENSIONS Model ICBIF15/S Model ICBIF15/S Low-profile lid Hidden 2600-watt heating element 533 mm OVERALL DEPTH Illuminated electronic touch controls 381 mm OVERALL WIDTH Graduated control lighting Deep drawn pan 191 mm 343 mm TO DRAIN OUTLET Location of rating plate Digital temperature readout ACCESSORIES Electric Fryer Module Filler strip Accessories are available through your Wolf dealer. 26 WOLF INTEGRATED MODULES PLANNING INFORMATION The illustrations provide the overall dimensions and finished cut-out dimensions that you need to plan for in your installation. IMPORTANT NOTE: Wolf does not recommend the use of downdraft ventilation with the fryer module. IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, refer to page 19 for countertop cut-out dimensions. ELECTRICAL REQUIREMENTS The Wolf International electric fryer module is CB approved and and is manufactured for a 220-240 V AC, 50/60 Hz electrical supply. Locate electrical within the shaded area shown in the illustration. The electric fryer module must be installed in a base cabinet with access to the bottom of the unit to drain the oil through a manual valve. The consumer must supply a heat resistant bucket to accept the drained oil. Refer to the illustration for location of the drain outlet. You must follow all local codes and ordinances when installing your service. The fryer module can accommodate a Wolf cooktop hood. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications. I N S TA L L AT I O N S P E C I F I C AT I O N S S P E C I F I C AT I O N S Model ICBIF15/S Model ICBIF15/S Electric Fryer Module 838 mm RECOMMENDED 330 mm max 51** CABINET WIDTH 457 mm 489 mm mm COOKTOP CUT-OUT DEPTH 64 mm min 178 mm min* 314 mm 194 mm DRAIN OUTLET LOCATION 914 mm STANDARD FLOOR TO COUNTERTOP HEIGHT COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 356 mm CUT-OUT TO COMBUSTIBLE COOKTOP CUT-OUT WIDTH MATERIALS (BOTH SIDES) 314 mm 152 mm DRAIN OUTLET LOCATION 762 mm 343 mm I N S TA L L AT I O N Refer to installation instructions shipped with each Wolf product for detailed specifications. Exterior Finish Classic Overall Width 381 mm Overall Height 343 mm Overall Depth 533 mm Heating Element 2600 W Cabinet Depth 578 mm min Height Clearance 343 mm min Cut-Out Width 356 mm Cut-Out Depth 489 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Electrical Rating 2.6 kW Shipping Weight 14 kg Unit dimensions may vary to ± 3 mm. E 381 mm 381 mm NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. NOTE: Fryer module must be installed in a base cabinet with access to manual valve at base of unit to drain oil into heat resistant receptacle. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. This fryer module must be installed at least 381 mm away from any open flame cooking device. The open flame may cause ignition of oil. 356 mm Countertop Cut-Out Dimensions COOKTOP CUT-OUT WIDTH 489 mm 64 mm min COOKTOP CUT-OUT DEPTH This fryer module must be installed at least 381 mm away from a Wolf steamer module, as contact between water and hot oil may cause burns from steam and hot oil. FRONT OF COUNTERTOP 27 WOLF INTEGRATED MODULES Model IIM15/S Gas Multi-Function Cooktop G A S M U LT I - F U N C T I O N C O O K T O P FEATURES It’s really a misnomer to describe this wonderful cooktop module as a wok instrument because it is much more than that. The large, low-profile grate will fit in nicely with any Wolf gas cooktop. Integrated design allows for installation of multiple cooktops or modules For true wok cooking, the burner sculpts the gas flame into a plume, focusing heat in the center of the wok, then dispersing it outward for precisely controlled cooking. The larger grate will handle your wok perfectly but will also accommodate your largest stockpots and Dutch ovens. The powerful burner exceeds 5.3 kW. The Wolf multi-function cooktop is available in classic stainless steel. Available in natural and LP gas Stainless steel top construction with classic stainless steel finish High output 5.3 kW burner Automatic electronic reignition system Illuminated control panel Individual spark ignition system Two interchangeable cast iron burner grates with matte porcelain finish—wok grate and lowprofile continuous grate Deep drawn burner pan G A S M U LT I - F U N C T I O N C O O K T O P F E AT U R E S OVERALL DIMENSIONS Model IIM15/S Gas Multi-Function Cooktop High-output 5.3 kW burner Wok grate shown 533 mm OVERALL DEPTH 381 mm OVERALL WIDTH Illuminated control panel Deep drawn pan 127 mm Continuous control knob ACCESSORIES Location of rating plate Gas Multi-Function Cooktop Filler strip Bracket supports for installation of two integrated modules with 762 mm downdraft Accessories are available through your Wolf dealer. 28 WOLF INTEGRATED MODULES PLANNING INFORMATION ELECTRICAL | GAS REQUIREMENTS The illustrations provide the overall dimensions and finished cut-out dimensions that you need to plan for in your installation. The Wolf International gas multifunction cooktop is CB approved and and is manufactured for a 220-240 V AC, 50/60 Hz electrical supply. Locate electrical within the shaded area shown. You must follow all local codes and ordinances when installing your service. IMPORTANT NOTE: When multiple cooktops or modules are installed side by side, refer to page 19 for countertop cut-out dimensions. IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. This cooktop can accommodate a Wolf cooktop hood or downdraft system. When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. Refer to pages 57–66 for ventilation specifications. The gas multi-function cooktop is designed to operate on natural gas at 12.5 mb or LP (propane) gas at 25 mb. The minimum line pressure for natural gas is 17.5 mb and 27.4 mb for LP gas. The maximum gas supply pressure to the regulator should never exceed 34.9 mb. It is supplied with an ISO 14 male gas connection at the right rear corner of the module. The male connector exits the unit straight down, and you are supplied with a regulator with two female connectors. I N S TA L L AT I O N S P E C I F I C AT I O N S MODEL OPTIONS Gas Multi-Function Cooktop Gas Multi-Function Cooktop Classic / Natural Gas IIM15/S Classic / LP Gas IIM15/S-LP S P E C I F I C AT I O N S Gas Multi-Function Cooktop 838 mm RECOMMENDED 330 mm max 64** mm CABINET WIDTH 457 mm 489 mm COOKTOP CUT-OUT DEPTH 64 mm min 178 mm min* 762 mm COUNTERTOP TO COMBUSTIBLE MATERIALS ABOVE COOKTOP 356 mm CUT-OUT TO COMBUSTIBLE COOKTOP CUT-OUT WIDTH MATERIALS (BOTH SIDES) 127 mm E 914 mm LOCATION OF GAS SUPPLY MAY ALSO EXTEND 127 mm ON FLOOR FROM BACK WALL STANDARD FLOOR TO COUNTERTOP HEIGHT G 381 mm 381 mm Overall Height 127 mm Overall Depth 533 mm Burner Rating 5.3 kW Cabinet Depth 578 mm min Height Clearance* 127 mm min Cut-Out Width 356 mm Cut-Out Depth 489 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Gas Rating 5.3 kW Shipping Weight 14 kg 381 mm LOCATION OF GAS SUPPLY MAY ALSO EXTEND 127 mm ON FLOOR FROM BACK WALL 127 mm 381 mm NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop. 356 mm Countertop Cut-Out Dimensions Overall Width *A minimum height clearance of 140 mm is required between countertop and any combustible surface directly below the cooktop. Unit dimensions may vary to ± 3 mm. COOKTOP CUT-OUT WIDTH I N S TA L L AT I O N 489 mm 64 mm min COOKTOP CUT-OUT DEPTH Refer to installation instructions shipped with each Wolf product for detailed specifications. FRONT OF COUNTERTOP 29 WOLF WARMING DRAWERS Model ICBWWD30 with Stainless Steel Drawer Front Model ICBWWD30 with Integrated Drawer Front WOLF WARMING DRAWER FEATURES Warming drawers have a clear mission in life— to take good care of good food until it’s time for you to eat. Our superior air control helps keep moist foods moist and crisp foods crisp. In addition, Wolf warming drawers are among the most spacious on the market, so you will have little problem storing items. Stainless steel drawer front and tubular handle There is a rack for stacking food plus an optional set of six stainless steel containers with lids that divide the drawer into sections, keeping different dishes warm at the same time. Preset automatic shut-off or extended operation in Sabbath Mode Electronic controls are hidden regardless of your panel selection. Choose from the classic stainless steel look or the integrated drawer front, which allows for a custom wood panel. Wolf offers optional decorative handles for the integrated drawer front. Keep in mind, there are significant changes to the installation procedure if you plan on using the integrated drawer front. Integrated drawer front allows for custom wood panel application 850-watt heating element Hidden electronic touch control panel Preset and variable temperature control Stainless steel interior Rack for stacking food Removable stainless steel drawer pan Full-extension, ball bearing drawer glides CE certified This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. W A R M I N G D R A W E R F E AT U R E S Model ICBWWD30 (stainless steel drawer front shown) Removable stainless steel drawer pan Galvanized exterior Rack for stacking food Stainless steel interior Hidden electronic touch control panel ACCESSORIES Warming Drawer Ball bearing drawer glides Location of rating plate Stainless steel drawer front shown (sold as an accessory) Six-piece container set—includes six stainless steel pans with lids; one 6.3 L pan, one 3.9 L pan, two 2.8 L pans, two 1.7 L pans and pan rack Accessories are available through your Wolf dealer. 30 WOLF WARMING DRAWERS PLANNING INFORMATION INTEGRATED DRAWER FRONT The Wolf 762 mm warming drawer is shipped without any decorative drawer front. You must order a stainless steel drawer front (tubular handle included) or the integrated front (no handle) for a custom wood application. IMPORTANT NOTE: A minimum 838 mm wide cabinet is required for the warming drawer with integrated drawer front. A minimum 610 mm deep cabinet is required for an overlay application and 635 mm deep cabinet for a flush inset application. Specifications on the following pages provide overall dimensions, rough openings and installation options for Model ICBWWD30 with stainless steel and integrated drawer fronts. Note that there are significant differences to the installation requirements for the integrated drawer front. An anti-tip block or platform must be installed to prevent the unit from tipping forward when the drawer is opened. The base platform must be able to support 91 kg. This platform must be a minimum of 25 mm above the toe kick to allow for the 16 mm overlap of the warming drawer trim. Model ICBWWD30 may be installed below a Wolf built-in oven or an electric or gas cooktop, provided the warming drawer is fully enclosed, top and bottom. It may also be installed next to or above another Model ICBWWD30. Dimensions will vary according to the specific installation. STAINLESS STEEL DRAWER FRONT Wolf recommends using a 838 mm wide cabinet for the warming drawer with stainless steel drawer front. A minimum 762 mm wide by 610 mm deep cabinet is required. Model ICBWWD30 with integrated drawer front can accommodate installations with a 762 mm or 914 mm cooktop. It may also be installed in combination with a 762 mm single or double oven or a 914 mm single oven. Dimensions will vary according to the specific installation. Keep in mind that the width of the custom panel for the warming drawer with integrated drawer front will vary according to the specific installation. The opening width will remain 749 mm whether installed in combination with a 762 mm or 914 mm cooktop or oven. ACCESSORIES Optional accessories are available through your Wolf dealer. The decorative wood drawer front panel must be a minimum of 16 mm thick. ELECTRICAL REQUIREMENTS Model ICBWWD30 is CB approved and manufactured for a 220-240 V AC, 50/60 Hz electrical supply. The service should have its own 15 or 20 amp circuit breaker, and a grounded 3-prong receptacle should be located within reach of the power cord and flush with the back wall. Locate electrical within the shaded area shown in the installation illustrations on the following pages. OVERALL DIMENSIONS Model ICBWWD30 with Stainless Steel Drawer Front 689 mm OVERALL DEPTH 260 mm 229 mm FRONT PANEL OPTIONS Model ICBWWD30 759 mm 597 mm OVERALL WIDTH BEHIND FRAME Classic Stainless Model ICBWWD30 with Integrated Drawer Front 257 mm 229 mm 746 mm 597 mm OVERALL WIDTH BEHIND FRAME WWDFRONT/S Integrated WWDFRONT/I (accepts wood panel) Optional drawer front panels are ordered and shipped as sales accessories. Stainless steel drawer front panels include matching tubular handle. 31 WOLF WARMING DRAWERS I N S TA L L AT I O N S P E C I F I C AT I O N S Model ICBWWD30 with Stainless Steel Drawer Front Undercounter Installation S P E C I F I C AT I O N S Model ICBWWD30 with Stainless Steel Drawer Front 838 mm RECOMMENDED CABINET WIDTH 51 mm x 51 mm Overall Width 759 mm Overall Height 260 mm Overall Depth (behind frame) 597 mm ANTI-TIP BLOCK 762 mm min DIMENSION WILL VARY* 127 mm 232 mm OPENING HEIGHT Interior Capacity 45 L Cabinet Width 838 mm rec 762 mm min 914 mm 606 mm min OPENING DEPTH Cabinet Depth 610 mm min Min Base Support 91 kg Opening Width 727 mm Opening Height 232 mm Opening Depth 606 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 or 20 amp circuit Heating Element 850 W Shipping Weight 45 kg 610 mm min STANDARD FLOOR TO COUNTER HEIGHT ALLOW FOR 16 mm OVERLAP OF DRAWER FACE ON ALL SIDES E 102 mm 727 mm 127 mm min OPENING WIDTH BOTTOM OF OPENING TO FLOOR CABINET DEPTH *Allow enough room for placement of anti-tip block and drawer face overlap. Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N OPTIONS Model ICBWWD30 with stainless steel drawer front may be installed above or below a Wolf 762 mm single or double oven, or below an electric or gas cooktop, provided the warming drawer is fully enclosed, top and bottom, with a minimum base support of 91 kg. Refer to the built-in oven and cooktop sections for additional specifications. It may also be installed next to or above another Model ICBWWD30. Model ICBWWD30 with stainless steel drawer front may be installed in combination with a 762 mm single oven. Refer to the installation instructions provided with the stainless steel drawer front for detailed specifications. These instructions can also be found on our website, wolfappliance.com. Dimensions will vary according to the specific installation. 32 Installation below 762 mm Built-In Single Oven 610 mm min 610 mm min CABINET DEPTH CABINET DEPTH 838 mm RECOMMENDED CABINET WIDTH 762 mm min 724 mm 610 mm min 691 mm 610 mm min 691 mm 762 mm OVEN ROUGH OPENING 22 mm 51 mm x 51 mm PLATFORM ANTI-TIP BLOCK 232 mm OPENING HEIGHT OPENING HEIGHT 606 mm min 606 mm min OPENING DEPTH OPENING DEPTH PLATFORM APPLICATION 127 E mm 232 mm 22 mm ANTI-TIP BLOCK APPLICATION 60 mm ALLOW FOR 16 mm OVERLAP OF DRAWER FACE ON ALL SIDES 102 mm 727 mm WARMING DRAWER OPENING WIDTH NOTE: Refer to the built-in 762 mm single oven specifications for electrical location. WOLF WARMING DRAWERS I N S TA L L AT I O N S P E C I F I C AT I O N S Model ICBWWD30 with Integrated Drawer Front Undercounter Installation S P E C I F I C AT I O N S Model ICBWWD30 with Integrated Drawer Front Overlay Application 838 mm 51 mm x 51 mm ANTI-TIP BLOCK DIMENSION WILL VARY* RECOMMENDED CABINET WIDTH 762 mm min 127 E mm 260 mm 251 mm OPENING HEIGHT 914 mm STANDARD FLOOR TO COUNTER HEIGHT 610 mm min OPENING DEPTH 610 mm min 102 mm ALLOW FOR OVERLAP OF DECORATIVE DRAWER FACE ON ALL SIDES** 749 mm OPENING WIDTH 127 mm min BOTTOM OF OPENING TO FLOOR CABINET DEPTH *Allow enough room for placement of anti-tip block and drawer face overlap. **Overlap of decorative drawer face will vary depending on the size of the custom panel. Flush Inset Application ANTI-TIP BLOCK DIMENSION WILL VARY* 746 mm Overall Height 257 mm Overall Depth (behind frame) 597 mm Interior Capacity 45 L Min Cabinet Width 838 mm Min Cabinet Depth Overlay Flush Inset 610 mm 635 mm Min Base Support 91 kg Opening Width 749 mm Opening Height 260 mm Opening Depth* 610 mm Min Panel Size (W x H) Overlay 762 mm x 264 mm Flush Inset 746 mm x 257 mm 838 mm 51 mm x 51 mm Overall Width MINIMUM CABINET WIDTH Min Panel Thickness 16 mm 127 E mm 260 mm 251 mm OPENING HEIGHT 102 mm 914 mm 610 mm + THICKNESS OF DRAWER FACE FOR OPENING DEPTH Electrical Supply 220-240 V AC, 50/60 Hz 15 or 20 amp circuit Heating Element 850 W Shipping Weight 45 kg 749 mm STANDARD FLOOR TO COUNTER HEIGHT OPENING WIDTH 127 mm min BOTTOM OF OPENING TO FLOOR 635 mm min *For flush inset application, add thickness of drawer face to opening depth. CABINET DEPTH Unit dimensions may vary to ± 3 mm. *Allow enough room for placement of anti-tip block. I N S TA L L AT I O N OPTIONS Installation below 762 mm Built-In Single Oven 610 mm min 635 mm min 838 mm CABINET DEPTH CABINET DEPTH CABINET WIDTH 610 mm min 691 mm 610 mm min 691 mm 724 mm 762 mm OVEN OPENING WIDTH 51 mm x 51 mm 51 mm x 51 mm ANTI-TIP BLOCK ANTI-TIP BLOCK 251 mm OPENING HEIGHT 610 mm min OPENING DEPTH OVERLAY APPLICATION 127 E mm 260 mm 260 mm 251 mm 38 mm min* OPENING HEIGHT 610 mm + THICKNESS OF DRAWER FACE FOR OPENING DEPTH FLUSH INSET APPLICATION 102 mm 38 mm min* 749 mm WARMING DRAWER OPENING WIDTH NOTE: Refer to the built-in 762 mm single oven specifications for electrical location. Model ICBWWD30 with integrated drawer front may be installed above or below any Wolf built-in oven, or below an electric or gas cooktop, provided the warming drawer is fully enclosed, top and bottom, with a minimum base support of 91 kg. Refer to the cooktop and oven sections for additional specifications. It may also be installed next to or above another Model ICBWWD30. Model ICBWWD30 with integrated drawer front may be installed in combination with a 762 mm or 914 mm single oven. Refer to the installation instructions provided for detailed specifications. These instructions can also be found on our website, wolfappliance.com. *Dimension may increase depending on the size of the drawer front panel. 33 WOLF DUAL FUEL RANGES WOLF DUAL FUEL RANGES With Wolf‘s dual fuel ranges you have state-ofthe-art cooking expertise in any number of sizes to meet the discriminating consumer’s precise needs. Patented features ensure this range stands out from the rest in performance and also beauty. T O P C O N F I G U R AT I O N S Dual Fuel Ranges IDF364C IDF486C IDF606CG IDF364G IDF486G IDF604CF IDF484CG IDF484F This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. Wolf dual fuel ranges come in 914 mm, 1219 mm and 1524 mm widths. Combined with the top configuration options, the different configurations you can choose from are numerous. Model numbers indicate the top configurations: (C) charbroiler, (G) griddle and (F) French Top. All Wolf dual fuel ranges come in the classic stainless steel finish. The electric oven(s) feature the Wolf exclusive dual convection system that delivers even temperature and airflow throughout. Its combination of convection fans and heating elements give the user convenience and superior control over ten different cooking modes. Advanced standard features such as dualstacked sealed burners, dual convection fans, cobalt blue porcelain oven interior, pivoting control panel, along with the Wolf exclusive infrared charbroiler, infrared griddle and French Top are all yours for the asking. The freedom to customize your dual fuel range will make you and your client look great. COOKING MODES Bake Roast Broil Convection Bake Convection Roast Convection Broil Convection Bake Stone* Dehydrate* Proof * Accessory required. 34 WOLF DUAL FUEL RANGES FEATURES Natural or LP gas rangetop with dual convection electric oven(s) Pivoting hidden touch control panel 457 mm oven on 1219 mm range is single convection Self-cleaning oven(s) with cobalt blue porcelain oven interior Optional infrared charbroiler, infrared griddle and French Top configurations Coaxial temperature-displaying oven selector knob Classic stainless steel exterior finish with island trim included Proof mode for 457 mm oven on 1219 mm range Distinctive red or black control knobs Temperature probe Platinum bezels surround all knobs—chrome or brass bezels optional Three removable oven racks, six-level rack guide and full-extension bottom rack Dual-stacked, sealed surface burners, all with simmer capabilities and automatic reignition at all settings Hidden bake element and recessed broil element 4.4 kW burners with .3 kW delivered at simmer 2.7 kW burner with .1 kW delivered at simmer and melt feature Ten cooking modes Triple-pane oven door window(s) and dual halogen lighting Spring/Damper door system on oven door(s) Adjustable stainless steel legs in front and adjustable rear casters Porcelain-coated cast iron continuous top grates D U A L F U E L R A N G E F E AT U R E S Model IDF484CG shown Infrared griddle (optional) Infrared charbroiler (optional) Continuous cast iron top grates ACCESSORIES Dual Fuel Ranges 127 mm and 254 mm classic stainless steel risers Stainless steel island trim Pivoting hidden control panel Dual-stacked, sealed burners Control knobs with platinum bezels Griddle indicator light Location of rating plate Chrome or brass bezels Coaxial oven selector knob Coaxial oven selector knob Porcelain-cast two-burner S-grate Stainless steel exterior finish Dual halogen oven lighting Single convection oven— 1219 mm range only Spring/Damper door system 508 mm classic stainless steel riser with shelf Red or black control knobs— must be ordered with the range One-piece wok grate and single burner grate Two-piece broiler pan and temperature probe Additional oven racks Hardwood cutting board— griddle models only Bake stone accessory Dehydration accessory Spring/Damper door system Front leg extension covers and rear leg caster covers Adjustable front legs and rear casters Blue porcelain oven interiors Dual convection oven Accessories are available through your Wolf dealer. 35 WOLF DUAL FUEL RANGES PLANNING INFORMATION ELECTRICAL | GAS REQUIREMENTS Wolf dual fuel ranges come in 914 mm, 1219 mm and 1524 mm widths. Specifications on the following pages provide overall dimensions, finished rough opening dimensions and installation specifics for each size of dual fuel range. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation. Specifications on the following pages provide electrical and gas requirements for each size of dual fuel range. IMPORTANT NOTE: Caution must be used in planning the proper installation of the Wolf dual fuel range to avoid fires or damage to adjacent cabinetry or kitchen equipment. Please follow the minimum clearances established in the finished rough opening dimensions. Refer to specifications on the following pages for your model. Locate electrical and gas supply within the shaded area shown in the Installation Specifications illustration for your model. International (I) models come with a factory installed transformer and require a 220-240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. The appropriate electrical connection must be provided in accordance with local requirements. Wolf dual fuel ranges are designed to operate on natural gas at 12.5 mb WC (water column) pressure or LP (propane) gas at 25 mb WC pressure. The minimum line pressure for natural gas is 17.5 mb WC and 27.4 mb WC for LP gas. The maximum gas supply pressure to the regulator should never exceed 34.9 mb WC; 3.5 kPa. Wolf recommends the use of a 13 mm I.D. commercial-type flex hose; this is the minimum size that may be used. All plumbing to the flex hose must be 19 mm minimum I.D. pipe. IMPORTANT NOTE: A separate external gas shut-off valve must be located near the range in an accessible location. You must follow all local codes and ordinances when installing your services. B U R N E R R AT I N G Dual Fuel Ranges Surface Burners 4.4 kW with .3 kW delivered at simmer (1) 2.7 kW with .1 kW delivered at simmer Infrared Charbroiler 4.7 kW Infrared Griddle Natural Gas LP Gas 4.4 kW 3.8 kW French Top 4.4 kW Refer to the specific model requirements for risers in non-island installations. 36 WOLF DUAL FUEL RANGES OVERALL DIMENSIONS 914 mm Dual Fuel Range S P E C I F I C AT I O N S 749 mm OVERALL DEPTH 914 mm Dual Fuel Range 699 mm Overall Width 235 mm 1445 mm WITH 508 mm RISER 616 mm 1191 mm 937 mm OVERALL HEIGHT TO COOKING SURFACE WITH 254 mm RISER 911 mm 1064 mm WITH 127 mm RISER 911 mm 1194 mm OVERALL WIDTH LEGS AND CASTERS ALLOW 54 mm HEIGHT ADJUSTMENT 911 mm Overall Height (to cooking surface) 937 mm Overall Depth 749 mm Overall Oven Interior Capacity 153 L Overall Interior Dim (W x H x D) 762 mm x 419 mm x 483 mm Usable Interior Dim (W x H x D) 673 mm x 419 mm x 416 mm Opening Width 914 mm Electrical Supply 220-240 V AC, 50/60 Hz 30 amp dedicated circuit Electrical Rating 5.2 kW at 240 V Total Amps 21.7 Shipping Weight 202–213 kg Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N S P E C I F I C AT I O N S MODEL OPTIONS 914 mm Dual Fuel Range 914 mm Dual Fuel Range Four Surface Burners 914 mm min 152 mm min 762 mm min TO 914 mm max 1118 mm min FOR CHARBROILER TO COMBUSTIBLE MATERIALS (BOTH SIDES) TO BOTTOM OF VENTILATION HOOD 330 mm max 457 mm min IMPORTANT NOTE: A minimum 254 mm riser is required when installing a 914 mm dual fuel range with a charbroiler or griddle against a combustible surface. TO COUNTERTOP 914 mm 914 mm 937 mm Refer to installation instructions shipped with each Wolf product for detailed specifications. TO COOKING SURFACE 381 mm LOCATION OF GAS SUPPLY IDF364G I N S TA L L AT I O N FINISHED ROUGH OPENING WIDTH 216 mm IDF364C Griddle Natural gas models listed; for LP gas add (-LP) to the model number. VENTILATION HOOD COUNTERTOP TO COMBUSTIBLE MATERIALS Charbroiler 83 mm 483 mm LOCATION OF GAS AND ELECTRICAL EXTENDS 76 mm ON FLOOR FROM BACK WALL LOCATION OF ELECTRICAL ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP– 0 mm TO NON-COMBUSTIBLE MATERIALS 37 WOLF DUAL FUEL RANGES OVERALL DIMENSIONS 1219 mm Dual Fuel Range S P E C I F I C AT I O N S 749 mm OVERALL DEPTH 1219 mm Dual Fuel Range Overall Width 699 mm 1216 mm 235 mm Overall Height (to cooking surface) 937 mm 1445 mm Overall Depth 749 mm Large Oven — Overall Interior Cap 127 L Overall Interior Dim (W x H x D) 635 mm x 419 mm x 483 mm Usable Interior Dim (W x H x D) 546 mm x 419 mm x 416 mm Small Oven — Overall Interior Cap 71 L Overall Interior Dim (W x H x D) 356 mm x 419 mm x 483 mm Usable Interior Dim (W x H x D) 295 mm x 419 mm x 416 mm Opening Width 1219 mm Electrical Supply 220-240 V AC, 50/60 Hz 50 amp dedicated circuit Electrical Rating 10.2 kW at 240 V Total Amps 42.5 Shipping Weight 302–340 kg WITH 508 mm RISER 616 mm 1191 mm 937 mm OVERALL HEIGHT TO COOKING SURFACE WITH 254 mm RISER 911 mm 1064 mm WITH 127 mm RISER 1194 mm 1216 mm OVERALL WIDTH LEGS AND CASTERS ALLOW 54 mm HEIGHT ADJUSTMENT Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N S P E C I F I C AT I O N S 1219 mm Dual Fuel Range MODEL OPTIONS 1219 mm Dual Fuel Range Six Surface Burners Charbroiler IDF486C Griddle IDF486G VENTILATION HOOD Four Surface Burners Charbroiler and Griddle IDF484CG French Top IDF484F 914 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS 152 mm min Natural gas models listed; for LP gas add (-LP) to the model number. IMPORTANT NOTE: A minimum 254 mm riser is required for all 1219 mm dual fuel range models installed against a combustible surface. 762 mm min TO 914 mm max 1118 mm min FOR CHARBROILER TO COMBUSTIBLE MATERIALS (BOTH SIDES) TO BOTTOM OF VENTILATION HOOD 330 mm max 457 mm min TO COUNTERTOP 1219 mm FINISHED ROUGH OPENING WIDTH 914 mm 937 mm TO COOKING SURFACE 254 mm 610 mm LOCATION OF GAS SUPPLY 83 mm 330 mm LOCATION OF GAS AND ELECTRICAL EXTENDS 76 mm ON FLOOR FROM BACK WALL 38 LOCATION OF ELECTRICAL ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP– 0 mm TO NON-COMBUSTIBLE MATERIALS WOLF DUAL FUEL RANGES OVERALL DIMENSIONS 1524 mm Dual Fuel Range S P E C I F I C AT I O N S 749 mm OVERALL DEPTH 1524 mm Dual Fuel Range 699 mm Overall Width 235 mm 1445 mm WITH 508 mm RISER 616 mm 1191 mm 937 mm OVERALL HEIGHT TO COOKING SURFACE WITH 254 mm RISER 911 mm 1064 mm WITH 127 mm RISER 1527 mm 1194 mm OVERALL WIDTH LEGS AND CASTERS ALLOW 54 mm HEIGHT ADJUSTMENT 1527 mm Overall Height (to cooking surface) 937 mm Overall Depth 749 mm Overall Oven Interior Capacity (per oven) 127 L Overall Interior Dim (W x H x D) 635 mm x 419 mm x 483 mm each Usable Interior Dim (W x H x D) 546 mm x 419 mm x 416 mm each Opening Width 1530 mm Electrical Supply 220-240 V AC, 50/60 Hz 50 amp dedicated circuit Electrical Rating 10.2 kW at 240 V Total Amps 42.5 Shipping Weight 397–431 kg Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N S P E C I F I C AT I O N S MODEL OPTIONS 1524 mm Dual Fuel Range 1524 mm Dual Fuel Range Six Surface Burners 914 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS 762 mm min TO 914 mm max 1118 mm min FOR CHARBROILER TO COMBUSTIBLE MATERIALS (BOTH SIDES) IDF606F Charbroiler and Griddle IDF606CG Natural gas models listed; for LP gas add (-LP) to the model number. VENTILATION HOOD 152 mm min French Top TO BOTTOM OF VENTILATION HOOD 330 mm max IMPORTANT NOTE: A minimum 254 mm riser is required for all 1524 mm dual fuel range models installed against a combustible surface. 457 mm min TO COUNTERTOP I N S TA L L AT I O N 1530 mm FINISHED ROUGH OPENING WIDTH 914 mm 937 mm TO COOKING SURFACE 254 mm 787 mm LOCATION OF GAS SUPPLY Refer to installation instructions shipped with each Wolf product for detailed specifications. 83 mm 330 mm LOCATION OF GAS AND ELECTRICAL EXTENDS 76 mm ON FLOOR FROM BACK WALL LOCATION OF ELECTRICAL ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP– 0 mm TO NON-COMBUSTIBLE MATERIALS 39 WOLF SEALED BURNER RANGETOPS WOLF SEALED BURNER RANGETOPS T O P C O N F I G U R AT I O N S Sealed Burner Rangetops ICBSRT304 ICBSRT364C ICBSRT364G ICBSRT486C ICBSRT486G ICBSRT484CG ICBSRT484F This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. 40 There’s a good reason why professional chefs choose gas cooking: control. The patented, dual-stacked sealed gas burners of our new sealed burner rangetop take control to a new level. Two levels, really. The upper-tier burner delivers maximum heat transfer at higher settings; the lower-tier continuous flame ably handles the subtleties of simmering and melting. Patented features along with the Wolf exclusive infrared charbroiler, infrared griddle and French Top ensure this rangetop stands out from the rest in performance as well as beauty. Wolf sealed burner rangetops come in 762 mm, 914 mm and 1219 mm widths and are available in natural or LP gas, with your choice of several top configurations. Model numbers indicate the top configurations; (C) charbroiler, (G) griddle and (F) French Top. The model number followed by (-LP) denotes an LP gas model. All Wolf sealed burner rangetops come in the classic stainless steel finish. WOLF SEALED BURNER RANGETOPS FEATURES Natural or LP gas models 5.0 kW burners with .3 kW delivered at simmer Classic stainless steel exterior finish with island trim 3.2 kW burner with .1 kW delivered at simmer and melt feature Optional infrared charbroiler, infrared griddle and French Top configurations Porcelain-coated cast iron continuous top grates Distinctive red control knobs—optional black knobs available at no cost Platinum bezels surround all knobs—chrome or brass bezels optional Dual-stacked, sealed surface burners, all with simmer capabilities and electronic reignition at all settings S E A L E D B U R N E R R A N G E T O P F E AT U R E S Model ICBSRT484CG shown Infrared griddle (optional) Infrared charbroiler (optional) Low-profile island trim Continuous, cast iron top grates Dual-stacked, sealed burners ACCESSORIES Sealed Burner Rangetops 127 mm and 254 mm classic stainless steel risers 508 mm classic stainless steel riser with shelf Stainless steel exterior finish Black control knobs—one set available at no cost Griddle indicator light Control knobs with platinum bezels Location of rating plate Chrome or brass bezels One-piece wok grate and single burner grate Porcelain-cast two-burner S-grate SRT/Downdraft trim kit—Model ICBSRT304 only Hardwood cutting board—griddle models only Accessories are available through your Wolf dealer. 41 WOLF SEALED BURNER RANGETOPS PLANNING INFORMATION ELECTRICAL | GAS REQUIREMENTS Wolf sealed burner rangetops come in 762 mm, 914 mm and 1219 mm widths. Specifications on the following pages provide overall dimensions, finished rough opening dimensions and installation specifics for each size of sealed burner rangetop. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation. Specifications on the following pages provide electrical and gas requirements for each size of sealed burner rangetop. IMPORTANT NOTE: Caution must be used in planning the proper installation of the Wolf sealed burner rangetop to avoid fires or damage to adjacent cabinetry or kitchen equipment. Please follow the minimum clearances established in the finished rough opening dimensions. Refer to specifications on the following pages for your model. A downdraft can be used with Model ICBSRT304. An accessory trim kit is necessary for this installation. Contact your Wolf dealer for details. The Wolf sealed burner rangetop is CB approved and manufactured for a 220-240 V AC, 50/60 Hz electrical supply to operate the electronic ignition system. The service should have its own 15 amp circuit breaker. IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. Wolf sealed burner rangetops are designed to operate without a regulator on natural gas at 17-25 mb pressure or LP (propane) gas at 25-45 mb. If local codes permit, a certified, .9 m long, 13 mm or 19 mm I.D. flexible metal appliance connector is recommended for connecting the rangetop to the gas supply line. The platform for the rangetop must be 19 mm thick and include a cut-out at the right rear for gas supply and electrical connections. Locate electrical and gas supply within the shaded area shown in the Installation Specifications illustration for your model. You must follow all local codes and ordinances when installing your services. B U R N E R R AT I N G Sealed Burner Rangetops Surface Burners 5.0 kW with .3 kW delivered at simmer (1) 3.2 kW with .1 kW delivered at simmer Infrared Charbroiler Natural Gas LP Gas 6.2 kW 5.4 kW Infrared Griddle Natural Gas LP Gas 5.5 kW 5.5 kW French Top 5.0 kW Refer to the specific model requirements for risers in non-island installations. 42 WOLF SEALED BURNER RANGETOPS OVERALL DIMENSIONS 762 mm Sealed Burner Rangetop S P E C I F I C AT I O N S 762 mm Sealed Burner Rangetop 724 mm OVERALL DEPTH Overall Width 699 mm 235 mm COOKING SURFACE WITH 508 mm RISER 318 mm 216 mm OVERALL HEIGHT WITH WITH 254 mm RISER 127 mm RISER 191 mm 759 mm 445 mm 759 mm Overall Height (to cooking surface) 216 mm Overall Depth 724 mm Opening Width 762 mm Opening Height 191 mm (platform to countertop) 616 mm Opening Depth 1219 mm Electrical Supply 220-240 V AC 50/60 Hz, 15 amp dedicated circuit Shipping Weight 73 kg OVERALL WIDTH Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N S P E C I F I C AT I O N S MODEL OPTIONS 762 mm Sealed Burner Rangetop 762 mm Sealed Burner Rangetops Four Surface Burners ICBSRT304 Natural gas model listed; for LP gas add (-LP) to the model number. VENTILATION HOOD I N S TA L L AT I O N 762 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS 330 mm max 762 mm min TO 914 mm max TO BOTTOM OF VENTILATION HOOD 152 mm min TO COMBUSTIBLE MATERIALS (BOTH SIDES) 457 mm min TO COUNTERTOP Refer to installation instructions shipped with each Wolf product for detailed specifications. COOKING SURFACE 216 mm 762 mm OPENING WIDTH 19 mm 19 mm 406 mm PLATFORM PLATFORM LOCATION OF GAS AND ELECTRICAL SUPPLY CUT-OUT WITHIN SHADED AREA THROUGH BOTTOM OF PLATFORM TOP VIEW OF PLATFORM 102 mm E 191 mm 914 mm 610 mm BACK WALL G 406 mm ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGETOP TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP– 0 mm TO NON-COMBUSTIBLE MATERIALS 43 WOLF SEALED BURNER RANGETOPS OVERALL DIMENSIONS 914 mm Sealed Burner Rangetop S P E C I F I C AT I O N S 914 mm Sealed Burner Rangetop 724 mm OVERALL DEPTH Overall Width 911 mm Overall Height (to cooking surface) 216 mm Overall Depth 724 mm Opening Width 914 mm COOKING SURFACE Opening Height 191 mm (platform to countertop) Opening Depth 1219 mm Electrical Supply 220-240 V AC 50/60 Hz, 15 amp dedicated circuit Shipping Weight 699 mm 235 mm WITH 508 mm RISER 318 mm 216 mm 191 mm OVERALL HEIGHT 911 mm 445 mm WITH WITH 254 mm 127 mm RISER RISER 616 mm OVERALL WIDTH 86–100 kg Unit dimensions may vary to ± 3 mm. MODEL OPTIONS I N S TA L L AT I O N S P E C I F I C AT I O N S 914 mm Sealed Burner Rangetops 914 mm Sealed Burner Rangetop Four Surface Burners Charbroiler ICBSRT364C Griddle ICBSRT364G Natural gas models listed; for LP gas add (-LP) to the model number. VENTILATION HOOD IMPORTANT NOTE: A minimum 254 mm riser is required for charbroiler (C) or griddle (G) models installed against a combustible surface. 914 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS 152 mm min 1118 mm min FOR CHARBROILER TO COMBUSTIBLE MATERIALS (BOTH SIDES) 762 mm min TO 914 mm min TO BOTTOM OF VENTILATION HOOD 330 mm max 457 mm min TO COUNTERTOP COOKING SURFACE 216 mm 914 mm FINISHED ROUGH OPENING WIDTH 19 mm 19 mm 406 mm PLATFORM PLATFORM LOCATION OF GAS AND ELECTRICAL SUPPLY CUT-OUT WITHIN SHADED AREA THROUGH BOTTOM OF PLATFORM TOP VIEW OF PLATFORM 102 mm E 191 mm 914 mm 610 mm BACK WALL G 406 mm ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGETOP TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP– 0 mm TO NON-COMBUSTIBLE MATERIALS 44 WOLF SEALED BURNER RANGETOPS OVERALL DIMENSIONS 1219 mm Sealed Burner Rangetop S P E C I F I C AT I O N S 1219 mm Sealed Burner Rangetop 724 mm OVERALL DEPTH Overall Width 699 mm 235 mm COOKING SURFACE WITH 508 mm RISER 318 mm 216 mm WITH WITH 254 mm 127 mm RISER RISER 191 mm OVERALL HEIGHT 1216 mm 445 mm 616 mm 1216 mm Overall Height (to cooking surface) 216 mm Overall Depth 724 mm Opening Width 1219 mm Opening Height 191 mm (platform to countertop) Opening Depth 1219 mm Electrical Supply 220-240 V AC 50/60 Hz, 15 amp dedicated circuit Shipping Weight 109–127 kg OVERALL WIDTH Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N S P E C I F I C AT I O N S MODEL OPTIONS 1219 mm Sealed Burner Rangetop 1219 mm Sealed Burner Rangetops Six Surface Burners Charbroiler ICBSRT486C Griddle ICBSRT486G Four Surface Burners VENTILATION HOOD 914 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS 152 mm min 762 mm min TO 914 mm max 1118 mm min FOR CHARBROILER TO COMBUSTIBLE MATERIALS (BOTH SIDES) TO BOTTOM OF VENTILATION HOOD 330 mm max 457 mm min COOKING SURFACE 216 mm 1219 mm 19 mm PLATFORM LOCATION OF GAS AND ELECTRICAL SUPPLY CUT-OUT WITHIN SHADED AREA THROUGH BOTTOM OF PLATFORM TOP VIEW OF PLATFORM 102 mm E PLATFORM 914 mm ICBSRT484F Natural gas models listed; for LP gas add (-LP) to the model number. 191 mm 19 mm 406 mm ICBSRT484CG French Top IMPORTANT NOTE: A minimum 254 mm riser is required for charbroiler (C) or griddle (G) models installed against a combustible surface. TO COUNTERTOP FINISHED ROUGH OPENING WIDTH Charbroiler and Griddle I N S TA L L AT I O N 610 mm Refer to installation instructions shipped with each Wolf product for detailed specifications. BACK WALL G 406 mm ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGETOP TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP– 0 mm TO NON-COMBUSTIBLE MATERIALS 45 WOLF GAS RANGES WOLF GAS RANGES If it looks as if it could be in a restaurant kitchen, well, that’s natural. That’s precisely where Wolf has spent the past seven decades, perfecting the form, function and sheer durability of our stainless steel gas ranges. T O P C O N F I G U R AT I O N S Gas Ranges IR304 IR364C IR486C IR364G IR486G IR484CG This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. 46 IR606CG Wolf gas ranges come in 762 mm, 914 mm, 1219 mm and 1524 mm widths, and combined with the top configuration options, the different configurations you can choose from are numerous. Model numbers indicate the top configurations: (C) charbroiler, (G) griddle and (F) French Top. Advanced standard features such as an infrared oven broiler, convection baking and dual burners along with the Wolf exclusive infrared charbroiler, infrared griddle and French Top are all yours for the asking. The freedom to customize your gas range will make you and your client look great. All Wolf gas ranges come in the classic stainless steel finish and are shipped with the distinctive red control knobs. Contact your Wolf dealer for optional black knobs available at no cost. WOLF GAS RANGES FEATURES Natural or LP gas models Large-capacity convection oven(s) with infrared broiler, porcelain interior, three adjustable racks, lights and door window Fits standard 610 mm deep cabinets with zero clearance for easy installation Optional infrared charbroiler, infrared griddle and French Top configurations Classic stainless steel exterior finish Dual brass burners with automatic reignition at all settings, .1 kW simmer to 4.7 kW high Porcelain-coated cast iron top grates Large red control knobs with four position settings and chrome bezels—optional black knobs available 457 mm oven with porcelain interior, two adjustable racks, lights and door window on 1219 mm range Spring/Damper door system on oven door(s) Stainless steel drip tray on ball bearing slides Adjustable 76 mm stainless steel legs in front and rear casters Full side panels and skirt G A S R A N G E F E AT U R E S Model IR484CG shown with 127 mm riser Porcelain-coated, cast iron top grates Infrared charbroiler (optional) Infrared griddle (optional) 127 mm riser (optional) Large red control knobs Dual brass burners Location of rating plate Burner drip pan Oven light switch Oven light switch Stainless steel exterior finish Pull-out drip tray Full side panels and skirt Convection fan switch Spring/Damper door system Oven indicator light ACCESSORIES Gas Ranges 457 mm oven— 1219 mm range only Large capacity convection oven Griddle indicator light 127 mm and 254 mm classic stainless steel risers 508 mm classic stainless steel riser with shelf Classic stainless steel island trim Black control knobs—available at no cost Porcelain-coated, cast iron wok grate Porcelain-coated, cast iron two-burner S-grate Hardwood cutting board—griddle models only Additional oven racks Accessories are available through your Wolf dealer. 47 WOLF GAS RANGES PLANNING INFORMATION ELECTRICAL | GAS REQUIREMENTS Wolf gas ranges come in 762 mm, 914 mm, 1219 mm and 1524 mm widths. Specifications on the following pages provide overall dimensions, finished rough opening dimensions and installation specifics for each size of gas range. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation. International (I) models come with a factory installed transformer and require a 220-240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. The appropriate electrical connection must be provided in accordance with local requirements. The service should have its own 15 amp circuit breaker. IMPORTANT NOTE: Caution must be used in planning the proper installation of the Wolf gas range to avoid fires or damage to adjacent cabinetry or kitchen equipment. Please follow the minimum clearances established in the finished rough opening dimensions. Refer to specifications on the following pages for your model. IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. Locate electrical and gas supply within the shaded area shown in the Installation Specifications illustration for your model. Wolf gas ranges are designed to operate on natural gas at 12.5 mb WC (water column) pressure or LP (propane) gas at 25 mb WC pressure. The minimum line pressure for natural gas is 17.5 mb WC and 27.4 mb WC for LP gas. The maximum gas supply pressure to the regulator should never exceed 34.9 mb WC; 3.5 kPa. Wolf recommends the use of a 13 mm I.D. commercial-type flex hose; this is the minimum size that may be used. All plumbing to the flex hose must be 19 mm minimum I.D. pipe. IMPORTANT NOTE: A separate external gas shut-off valve must be located near the range in an accessible location. You must follow all local codes and ordinances when installing your services. B U R N E R R AT I N G Gas Ranges Surface Burners 4.7 kW with .1 kW delivered at simmer Infrared Charbroiler 4.7 kW Infrared Griddle 5.3 kW French Top 4.4 kW Oven Burner (Bake) 8.8 kW Infrared Oven Broiler 5.3 kW Refer to the specific model requirements for risers in non-island installations. 48 WOLF GAS RANGES OVERALL DIMENSIONS 762 mm Gas Range 721 mm S P E C I F I C AT I O N S OVERALL DEPTH 762 mm Gas Range 692 mm Overall Width 235 mm 1441 mm WITH 508 mm RISER 622 mm 1187 mm 940 mm WITH 254 mm RISER 914 mm OVERALL HEIGHT TO COOKING SURFACE 1060 mm WITH 127 mm RISER 64 mm 762 mm 641 mm OVERALL WIDTH 762 mm Overall Height (to cooking surface) 940 mm Overall Depth 721 mm Overall Oven Interior Capacity 125 L Overall Interior Dim (W x H x D) 610 mm x 473 mm x 432 mm Usable Interior Dim (W x H x D) 610 mm x 419 mm x 432 mm Opening Width 768 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Power Cord 1.8 m 3-prong Shipping Weight 147 kg 1102 mm LEGS AND CASTERS ALLOW 25 mm HEIGHT ADJUSTMENT Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N S P E C I F I C AT I O N S MODEL OPTIONS 762 mm Gas Range 762 mm Gas Range Four Surface Burners IR304 Natural gas model listed; for LP gas add (-LP) to the model number. VENTILATION HOOD IMPORTANT NOTE: A minimum 127 mm riser is required when installing a 762 mm gas range against a combustible surface. 762 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS 330 mm max 762 mm TO 914 mm 152 mm min 457 mm min COUNTERTOP TO BOTTOM OF VENTILATION HOOD TO COMBUSTIBLE MATERIALS (BOTH SIDES) I N S TA L L AT I O N TO COUNTERTOP Refer to installation instructions shipped with each Wolf product for detailed specifications. 768 mm FINISHED ROUGH OPENING WIDTH 254 mm 203 mm 140 mm 914 mm 940 mm 305 mm E TO COOKING SURFACE 51 mm G 305 mm 127 mm 76 LOCATION OF GAS SUPPLY EXTENDS 76 mm ON FLOOR FROM BACK WALL mm ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP – 0 mm TO NON-COMBUSTIBLE MATERIALS 49 WOLF GAS RANGES OVERALL DIMENSIONS 914 mm Gas Range S P E C I F I C AT I O N S 721 mm OVERALL DEPTH 914 mm Gas Range Overall Width 692 mm 914 mm 235 mm Overall Height (to cooking surface) 940 mm Overall Depth 1441 mm 721 mm Overall Oven Interior Capacity 156 L Overall Interior Dim (W x H x D) 762 mm x 473 mm x 432 mm Usable Interior Dim (W x H x D) 762 mm x 419 mm x 432 mm Opening Width 921 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Power Cord 1.8 m 3-prong Shipping Weight 202–213 kg WITH 508 mm RISER 622 mm 1187 mm 940 mm WITH 254 mm RISER 914 mm OVERALL HEIGHT TO COOKING SURFACE 1060 mm WITH 127 mm RISER 64 mm 914 mm 641 mm OVERALL WIDTH 1102 mm LEGS AND CASTERS ALLOW 25 mm HEIGHT ADJUSTMENT Unit dimensions may vary to ± 3 mm. MODEL OPTIONS I N S TA L L AT I O N S P E C I F I C AT I O N S 914 mm Gas Range 914 mm Gas Range Four Surface Burners Charbroiler IR364C Griddle IR364G Natural gas models listed; for LP gas add (-LP) to the model number. VENTILATION HOOD IMPORTANT NOTE: A minimum 254 mm riser is required when installing a gas range with a charbroiler or griddle against a combustible surface. 762 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS 152 mm min TO COMBUSTIBLE MATERIALS (BOTH SIDES) 914 mm min FOR 330 mm max 762 mm TO 914 mm CHARBROILER COUNTERTOP TO BOTTOM OF VENTILATION HOOD 457 mm min TO COUNTERTOP 921 mm FINISHED ROUGH OPENING WIDTH 254 mm 203 mm 140 mm 940 mm 305 mm TO COOKING SURFACE E 51 mm G 305 mm ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP – 0 mm TO NON-COMBUSTIBLE MATERIALS 50 914 mm 127 mm 76 LOCATION OF GAS SUPPLY EXTENDS 76 mm ON FLOOR FROM BACK WALL mm WOLF GAS RANGES OVERALL DIMENSIONS 1219 mm Gas Range S P E C I F I C AT I O N S 721 mm OVERALL DEPTH 1219 mm Gas Range 692 mm Overall Width 235 mm 1441 mm WITH 508 mm RISER 622 mm 1187 mm 940 mm WITH 254 mm RISER 914 mm OVERALL HEIGHT TO COOKING SURFACE 1060 mm WITH 127 mm RISER 64 mm 1219 mm 641 mm OVERALL WIDTH 1219 mm Overall Height (to cooking surface) 940 mm 1102 mm LEGS AND CASTERS ALLOW 25 mm HEIGHT ADJUSTMENT Overall Depth 721 mm Large Oven — Overall Interior Cap 125 L Overall Interior Dim (W x H x D) 610 mm x 473 mm x 432 mm Usable Interior Dim (W x H x D) 610 mm x 419 mm x 432 mm Small Oven — Overall Interior Cap 71 L Overall Interior Dim (W x H x D) 343 mm x 473 mm x 432 mm Usable Interior Dim (W x H x D) 343 mm x 419 mm x 432 mm Opening Width 1226 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Power Cord 1.8 m 3-prong Shipping Weight 295–340 kg Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N S P E C I F I C AT I O N S 1219 mm Gas Range MODEL OPTIONS 1219 mm Gas Range Six Surface Burners Charbroiler IR486C Griddle IR486G VENTILATION HOOD Four Surface Burners Charbroiler and Griddle IR484CG 762 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS 152 mm min TO COMBUSTIBLE MATERIALS (BOTH SIDES) 762 mm TO 914 mm COUNTERTOP TO BOTTOM OF VENTILATION HOOD 914 mm min FOR CHARBROILER 330 mm max 457 mm min TO COUNTERTOP IMPORTANT NOTE: A minimum 254 mm riser is required when installing a gas range with a charbroiler or griddle against a combustible surface. 1226 mm FINISHED ROUGH OPENING WIDTH 914 mm 940 mm 305 mm 660 mm 203 mm 140 mm Natural gas models listed; for LP gas add (-LP) to the model number. TO COOKING SURFACE E 51 mm G 305 mm 127 mm 76 LOCATION OF GAS SUPPLY EXTENDS 76 mm ON FLOOR FROM BACK WALL mm ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP – 0 mm TO NON-COMBUSTIBLE MATERIALS 51 WOLF GAS RANGES OVERALL DIMENSIONS 1524 mm Gas Range S P E C I F I C AT I O N S 721 mm OVERALL DEPTH 1524 mm Gas Range Overall Width 692 mm 1524 mm 235 mm Overall Height (to cooking surface) 940 mm Overall Depth 1441 mm 721 mm Overall Oven Interior Capacity (per oven) 125 L WITH 508 mm RISER 622 mm Overall Interior Dim (W x H x D) 610 mm x 473 mm x 432 mm each Usable Interior Dim (W x H x D) 610 mm x 419 mm x 432 mm each Opening Width 1530 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Power Cord 1.8 m 3-prong Shipping Weight 397–431 kg 1187 mm WITH 254 mm RISER 940 mm 914 mm OVERALL HEIGHT TO COOKING SURFACE 1060 mm WITH 127 mm RISER 64 mm 1524 mm 641 mm OVERALL WIDTH 1102 mm LEGS AND CASTERS ALLOW 25 mm HEIGHT ADJUSTMENT Unit dimensions may vary to ± 3 mm. MODEL OPTIONS I N S TA L L AT I O N S P E C I F I C AT I O N S 1524 mm Gas Range 1524 mm Gas Range Four Surface Burners Charbroiler and Griddle IR606CG Natural gas models listed; for LP gas add (-LP) to the model number. VENTILATION HOOD IMPORTANT NOTE: A minimum 254 mm riser is required when installing a gas range with a charbroiler or griddle against a combustible surface. 152 mm min I N S TA L L AT I O N TO COMBUSTIBLE MATERIALS (BOTH SIDES) 1118 mm min 762 mm TO 914 mm COUNTERTOP TO COMBUSTIBLE MATERIALS COUNTERTOP TO BOTTOM OF VENTILATION HOOD Refer to installation instructions shipped with each Wolf product for detailed specifications. TO COUNTERTOP 1530 mm FINISHED ROUGH OPENING WIDTH 914 mm 254 mm 203 mm 940 mm 305 mm TO COOKING SURFACE E 140 mm ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGE TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP – 0 mm TO NON-COMBUSTIBLE MATERIALS 52 330 mm max 457 mm min 51 mm G 305 mm 127 mm 76 LOCATION OF GAS SUPPLY EXTENDS 76 mm ON FLOOR FROM BACK WALL mm WOLF GAS RANGETOPS WOLF GAS RANGETOPS If you want to offer a more professional look to your client’s kitchen and still use a cooktop, look to the rangetops from Wolf. They offer you that commercial look but give you flexibility to use the ovens in other locations in the kitchen. In fact, the Wolf framed ovens would be a beautiful complement to these cooking instruments. Choose from four or six dual burners or consider the Wolf exclusive infrared charbroiler, infrared griddle or French Top for the ultimate in restaurant cooking in the home. Wolf gas rangetops come in 914 mm and 1219 mm widths and are available in natural or LP gas, with your choice of several top configurations. Model numbers indicate the top configurations: (C) charbroiler, (G) griddle and (F) French Top. All Wolf gas rangetops come in the classic stainless steel finish and are shipped with the distinctive red control knobs. Contact your Wolf dealer for optional black knobs available at no cost. The dual burners can produce 4.7 kW for professional cooking heat or as little as .1 kW for those delicate sauces. G A S R A N G E T O P F E AT U R E S T O P C O N F I G U R AT I O N S Model IRT484CG shown with island trim Gas Rangetops Infrared charbroiler (optional) Infrared griddle (optional) Porcelain-coated cast iron top grates Low-profile island trim Dual brass burners IRT364C IRT486C IRT364G IRT486G Stainless steel exterior finish Location of rating plate Pull-out drip tray Large red control knobs Griddle indicator light IRT484CG ACCESSORIES Gas Rangetops 267 mm classic stainless steel riser Classic stainless steel island trim Black control knobs—available at no cost IRT484F This appliance is certified by Star-K to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. Porcelain-coated, cast iron wok grate Porcelain-coated, cast iron two-burner S-grate Hardwood cutting board—griddle models only Accessories are available through your Wolf dealer. 53 WOLF GAS RANGETOPS FEATURES ELECTRICAL | GAS REQUIREMENTS Natural or LP gas models Specifications on the following pages provide electrical and gas requirements for each size of gas rangetop. Fits standard 610 mm deep cabinets with zero clearance for easy installation Porcelain-coated cast iron top grates International (I) models come with a factory installed transformer and require a 220-240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. The appropriate electrical connection must be provided in accordance with local requirements. The service should have its own 15 amp circuit breaker. Large red control knobs with four position settings and chrome bezels—optional black knobs available IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. Stainless steel drip tray on ball bearing slides Wolf gas rangetops are designed to operate on natural gas at 12.5 mb WC (water column) pressure or LP (propane) gas at 25 mb WC pressure. The minimum line pressure for natural gas is 17.5 mb WC and 27.4 mb WC for LP gas. The maximum gas supply pressure to the regulator should never exceed 34.9 mb WC; 3.5 kPa. Optional infrared charbroiler, infrared griddle and French Top configurations Classic stainless steel exterior finish Dual brass burners with automatic reignition at all settings, .1 kW simmer to 4.7 kW high PLANNING INFORMATION Wolf gas rangetops come in 914 mm and 1219 mm widths. Specifications on the following pages provide overall dimensions, finished rough opening dimensions and installation specifics for each size of gas rangetop. We have minimized the information contained in the illustrations, concentrating on the critical information you need to plan your installation. IMPORTANT NOTE: Caution must be used in planning the proper installation of the Wolf gas rangetop to avoid fires or damage to adjacent cabinetry or kitchen equipment. Follow the minimum clearances established in the finished rough opening dimensions. Refer to specifications on the following pages for your model. Wolf recommends the use of a 13 mm I.D. commercial-type flex hose; this is the minimum size that may be used. All plumbing to the flex hose must be 19 mm minimum I.D. pipe. IMPORTANT NOTE: A separate external gas shut-off valve must be located near the range in an accessible location. The platform for the rangetop must be 19 mm thick and include a cut-out at the right rear for gas supply and electrical connections. Locate electrical and gas supply within the shaded area shown in the Installation Specifications illustration for your model. You must follow all local codes and ordinances when installing your services. B U R N E R R AT I N G Gas Rangetops Surface Burners 4.7 kW with .1 kW delivered at simmer Infrared Charbroiler 4.7 kW Infrared Griddle 5.3 kW French Top 4.4 kW Refer to the specific model requirements for risers in non-island installations. 54 WOLF GAS RANGETOPS OVERALL DIMENSIONS 914 mm Gas Rangetop S P E C I F I C AT I O N S 914 mm Gas Rangetop 692 mm OVERALL DEPTH TO KNOBS COOKING SURFACE 508 mm WITH 267 mm RISER 267 mm 241 mm 914 mm Overall Width 914 mm Overall Height (to cooking surface) 267 mm 70 mm OVERALL HEIGHT 51 mm Overall Depth 692 mm Opening Width 921 mm Opening Height 241 mm (platform to countertop) 610 mm Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Power Cord 1.8 m 3-prong Shipping Weight 86–100 kg OVERALL WIDTH Unit dimensions may vary to ± 3 mm. I N S TA L L AT I O N S P E C I F I C AT I O N S MODEL OPTIONS 914 mm Gas Rangetop 914 mm Gas Rangetop Four Surface Burners 762 mm min 152 mm min 762 mm min 914 mm min FOR CHARBROILER TO COMBUSTIBLE MATERIALS (BOTH SIDES) TO 914 mm max COUNTERTOP TO BOTTOM OF VENTILATION HOOD I N S TA L L AT I O N 241 mm 13 mm E G 203 mm 203 mm 356 mm LOCATION OF GAS AND ELECTRICAL SUPPLY CUT-OUT WITHIN SHADED AREA THROUGH BOTTOM OF PLATFORM IMPORTANT NOTE: In nonisland applications, a riser is required when installing a 914 mm gas rangetop against a combustible surface. TO COUNTERTOP OPENING HEIGHT BACK WALL 76 mm 330 mm max 921 mm TOP VIEW OF PLATFORM IRT364G 457 mm min FINISHED ROUGH OPENING WIDTH 19 mm PLATFORM IRT364C Griddle Natural gas models listed; for LP gas add (-LP) to the model number. VENTILATION HOOD COUNTERTOP TO COMBUSTIBLE MATERIALS Charbroiler 914 mm 19 mm PLATFORM 70 mm Refer to installation instructions shipped with each Wolf product for detailed specifications. 610 mm ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGETOP TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP– 0 mm TO NON-COMBUSTIBLE MATERIALS 55 WOLF GAS RANGETOPS OVERALL DIMENSIONS 1219 mm Gas Rangetop S P E C I F I C AT I O N S 1219 mm Gas Rangetop 692 mm Overall Width OVERALL DEPTH TO KNOBS 1219 mm Overall Height (to cooking surface) 267 mm Overall Depth 692 mm Opening Width 1226 mm COOKING SURFACE OVERALL HEIGHT 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Power Cord 1.8 m 3-prong Shipping Weight 100–127 kg 70 mm 508 mm WITH 267 mm RISER 267 mm Opening Height 241 mm (platform to countertop) Electrical Supply 51 mm 241 mm 1219 mm 610 mm OVERALL WIDTH Unit dimensions may vary to ± 3 mm. MODEL OPTIONS I N S TA L L AT I O N S P E C I F I C AT I O N S 1219 mm Gas Rangetop 1219 mm Gas Rangetop Six Surface Burners Charbroiler IRT486C Griddle IRT486G Four Surface Burners Charbroiler and Griddle IRT484CG French Top VENTILATION HOOD IRT484F Natural gas models listed; for LP gas add (-LP) to the model number. IMPORTANT NOTE: In nonisland applications, a riser is required when installing a 1219 mm gas rangetop against a combustible surface. 762 mm min COUNTERTOP TO COMBUSTIBLE MATERIALS 762 mm min TO 914 mm max COUNTERTOP TO BOTTOM OF VENTILATION HOOD 914 mm min 152 mm min FOR CHARBROILER TO COMBUSTIBLE MATERIALS (BOTH SIDES) 1226 mm 241 mm OPENING HEIGHT TOP VIEW OF PLATFORM 13 mm BACK WALL E TO COUNTERTOP FINISHED ROUGH OPENING WIDTH 19 mm PLATFORM 76 mm 330 mm max 457 mm min G 406 mm 406 mm 356 mm LOCATION OF GAS AND ELECTRICAL SUPPLY CUT-OUT WITHIN SHADED AREA THROUGH BOTTOM OF PLATFORM 914 mm 19 mm PLATFORM 70 mm 610 mm ISLAND INSTALLATIONS: 305 mm MINIMUM CLEARANCE FROM BACK OF RANGETOP TO COMBUSTIBLE REAR WALL ABOVE COUNTERTOP– 0 mm TO NON-COMBUSTIBLE MATERIALS 56 WOLF COOKTOP VENTILATION WOLF E SERIES COOKTOP HOODS FEATURES Behind the contemporary lines of the Wolf E Series cooktop hoods, there's a lot of hardnosed functional thinking. Brilliant halogen lighting illuminates your cooking surface. Powerful multi-speed blowers whisk away smoke and odors. Wall-mount hoods in three widths and island hood are available in classic stainless steel. Classic stainless steel finish E Series cooktop wall and island hoods are recommended for use with Wolf electric and gas cooktops and integrated modules. Internal and remote blower options Front-mounted electronic controls with digital indicator Heavy-duty stainless steel construction Four-speed blower control Model ICTEWH30I Filter clean indicator lets you know when the filter needs cleaning Delay-off feature automatically turns unit off Sealed halogen lighting with three settings Stainless steel filter cover with dishwasher-safe aluminum mesh filter Heat sentry feature automatically turns unit on when heat is sensed and automatically adjusts blower speed Model ICTEWH36I Hood can be ducted to the outside or nonducted using a charcoal filter (internal blower (I) models only) Transition with back draft damper included Fits 2.4 m to 2.7 m ceilings Model ICTEWH45I W O L F E S E R I E S C O O K T O P H O O D F E AT U R E S Model ICTEWH36I shown Model ICTEIH42I Classic stainless steel finish Telescopic flue Transition with backdraft damper (I) Models include 500 CFM Internal blower Dishwasher-safe filter Filter clean indicator MODEL OPTIONS E Series Cooktop Hoods Wall Hoods Four-speed blower control Location of rating plate Halogen lighting Electronic controls with digital indicator 762 mm Width ICTEWH30I* 914 mm Width ICTEWH36I ICTEWH36I* 1143 mm Width ICTEWH45I* Island Hood ICTEIH42I* *500 CFM internal blower included. 57 WOLF COOKTOP VENTILATION PLANNING INFORMATION ELECTRICAL REQUIREMENTS Wolf E Series cooktop wall hoods are 450 mm deep and come in 762 mm, 914 mm and 1143 mm widths. The island hood is 1067 mm wide by 550 mm deep. (I) models include a 500 CFM internal blower. Wolf E Series cooktop wall and island hoods require a separate, grounded 220-240 V AC, 50/60 Hz power supply with a dedicated 15 amp circuit. Placement of the electrical supply is not critical, as long as it is accessible IMPORTANT NOTE: E Series cooktop wall and island hoods are recommended for use with Wolf electric and gas cooktops along with integrated modules, and should be at least as wide as the cooking surface. Locate electrical within the shaded area shown in the Installation Specifications illustration for your model. Wolf E Series cooktop wall and island hoods come with a telescopic flue that allows you to reach a ceiling height of 2.4 m to 2.7 m with a finished look. Specifications on the following pages provide overall dimensions, blower and ducting considerations, and installation specifics for cooktop wall and island hoods. We have minimized the information contained in the illustrations, concentrating on the critical information you must plan into your installation. Installation of the cooktop wall or island hood should be 650 mm to 760 mm from the bottom of the hood to the countertop. ACCESSORIES E Series Cooktop Hoods Internal and remote blower assemblies Charcoal filters for non-ducted applications (internal blower (I) models only) Accessories are available through your Wolf dealer. 58 IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. You must follow all local codes and ordinances when installing your service. WOLF COOKTOP VENTILATION OVERALL DIMENSIONS E Series Cooktop Wall Hoods Model ICTEWH30I S P E C I F I C AT I O N S 250 mm Model ICTEWH30I 274 mm 200 mm TO 620 mm Hood Type Wall Hood Overall Width 762 mm Overall Height 80 mm (excluding chimney) 790 mm TO 1210 mm 510 mm OVERALL HEIGHT 80 mm 762 mm 450 mm OVERALL WIDTH OVERALL DEPTH Models ICTEWH36 and ICTEWH36I 250 mm 274 mm 200 mm TO 620 mm 790 mm Overall Height (including chimney) 790 mm Maximum Height (full extension) 1210 mm Overall Depth 450 mm Bottom of Hood to Countertop 650 mm to 760 mm Duct Size 150 mm Round Discharge Vertical Internal Blower 500 CFM included Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Shipping Weight (shell only) 18 kg TO 1210 mm 510 mm OVERALL HEIGHT S P E C I F I C AT I O N S 80 mm 914 mm OVERALL WIDTH 450 mm OVERALL DEPTH Models ICTEWH36 and ICTEWH36I Hood Type Wall Hood Overall Width 914 mm Overall Height 80 mm (excluding chimney) Model ICTEWH45 250 mm 274 mm 200 mm TO 620 mm 790 mm TO 1210 mm 510 mm OVERALL HEIGHT 80 mm 1143 mm OVERALL WIDTH 450 mm OVERALL DEPTH OVERALL DIMENSIONS E Series Cooktop Island Hood — Model ICTEIH42 297 mm Overall Height (including chimney) 790 mm Maximum Height (full extension) 1210 mm Overall Depth 450 mm Bottom of Hood to Countertop 650 mm to 760 mm Duct Size 150 mm Round Discharge Vertical Internal Blower 500 CFM included with Model ICTEWH36I Blower Options Contact your Wolf dealer Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Shipping Weight (shell only) 21 kg 251 mm 222 mm TO *Blower options vary with the cooking surface. Refer to the cooktop ventilation recommendations on pages 68–69. 642 mm 790 mm TO 1210 mm 488 mm OVERALL HEIGHT 80 mm 1067 mm OVERALL WIDTH 550 mm OVERALL DEPTH 59 WOLF COOKTOP VENTILATION I N S TA L L AT I O N S P E C I F I C AT I O N S E Series Cooktop Wall Hoods S P E C I F I C AT I O N S Model ICTEWH45I Hood Type Wall Hood Overall Width 1143 mm 1210 mm MAXIMUM HEIGHT OF HOOD Overall Height 80 mm (excluding chimney) Overall Height (including chimney) 790 mm Maximum Height (full extension) 1210 mm Overall Depth 450 mm Bottom of Hood to Countertop 650 mm to 760 mm Duct Size 150 mm Round Discharge Vertical Internal Blower 500 CFM included Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Shipping Weight (shell only) 26 kg 790 mm MINIMUM HEIGHT OF HOOD 762 mm, 914 mm OR 1143 mm 450 mm OVERALL DEPTH OVERALL WIDTH 2.4 m TO 2.7 m 650 mm FLOOR TO CEILING HEIGHT TO 760 mm TO COUNTERTOP S P E C I F I C AT I O N S Model ICTEIH42I Hood Type Island Hood Overall Width 1067 mm Overall Height 80 mm (excluding chimney) Overall Height (including chimney) 790 mm Maximum Height (full extension) 1210 mm Overall Depth 550 mm Bottom of Hood to Countertop 650 mm to 760 mm Duct Size 150 mm Round Discharge Vertical Internal Blower 500 CFM included Electrical Supply 220-240 V AC, 50/60 Hz 15 amp dedicated circuit Shipping Weight (shell only) 32 kg I N S TA L L AT I O N S P E C I F I C AT I O N S E Series Cooktop Island Hood 1210 mm MAXIMUM HEIGHT OF HOOD 790 mm MINIMUM HEIGHT OF HOOD 550 mm OVERALL DEPTH 1067 mm OVERALL WIDTH 2.4 m TO 2.7 m FLOOR TO CEILING HEIGHT 650 mm TO 760 mm TO COUNTERTOP 60 WOLF COOKTOP VENTILATION BLOWER CONSIDERATIONS DUCTING CONSIDERATIONS Except for Model ICTEWH36, which is shipped without a blower assembly, E Series cooktop hoods include a 500 CFM internal blower. Wolf internal and remote blowers are available for Model ICTEWH36. Models with an internal blower can also use the charcoal filter if the hood will not be ducted to the outside. Charcoal filters are available as a sales accessory. Contact your local Wolf dealer for more information on remote blowers and charcoal filters. IMPORTANT NOTE: E Series cooktop hoods can be ducted to the outside or using a sales accessory charcoal filter, in a non-ducting installation (internal blower (I) models only). For Model ICTEWH36, the blower will vary in size when ducted to the outside. Blower size is dictated by the cooking surface, the volume of air to be moved and the length of the duct run. A straight, short duct run with a limited number of elbows and transitions will allow the ventilation hood to perform most efficiently. Wolf cooktop wall and island hoods have an 150 mm round vertical discharge. Ducting can run through the roof, external wall or eave. Ducting through an eave requires an internal blower. Refer to the illustrations below. E Series cooktop wall and island hoods will operate most efficiently when ductwork does not exceed 15 m in length. Local building codes may require the use of make-up air. Consult your local HVAC professional for specific requirements in your area. A remote-mounted blower will minimize the amount of blower noise, but will not eliminate the noise completely. All remote blowers will require a transition to a 254 mm duct. D U C T I N G C O N S I D E R AT I O N S E Series Cooktop Wall Hoods E Series Cooktop Island Hood DUCTWORK INSTALLATION THROUGH ROOF DUCTWORK INSTALLATION THROUGH ROOF ROOF CAP OR REMOTE BLOWER ROOF CAP OR REMOTE BLOWER 150 mm ROUND DUCT 150 mm ROUND DUCT WALL CAP OR REMOTE BLOWER 790 mm TELESCOPIC CHIMNEY FLUE TO 1210 mm HEIGHT OF HOOD 150 mm ROUND ELBOW 150 mm ROUND ELBOW TELESCOPIC CHIMNEY FLUE 790 mm DUCTWORK INSTALLATION THROUGH WALL EAVE VENT TO 1210 mm HEIGHT OF HOOD 150 mm ROUND VERTICAL DISCHARGE 150 mm ROUND VERTICAL DISCHARGE DUCTWORK INSTALLATION THROUGH EAVE – INTERNAL BLOWER ONLY 80 mm 80 mm 450 mm HOOD DEPTH 550 mm OVERALL DEPTH 650 mm 650 mm TO 760 mm COUNTERTOP TO BOTTOM OF HOOD TO 760 mm COUNTERTOP TO BOTTOM OF HOOD 61 WOLF COOKTOP VENTILATION Model DD30 Model DD36 WOLF DOWNDRAFT SYSTEMS FEATURES The cooktop downdraft unit rises from the countertop to whisk away odors and smoke into the easy-to-clean, five-layer mesh filter. The control module and top cover are available in classic stainless steel. Classic stainless steel control module and top cover Wolf downdraft systems come in 762 mm, 914 mm and 1143 mm widths and are recommended for use with Wolf framed electric cooktops, gas cooktops and integrated modules. IMPORTANT NOTE: Wolf downdraft ventilation systems are not recommended for use with the electric grill, steamer and fryer modules. Model DD45 A downdraft can be used with sealed burner rangetop Model ICBSRT304. An accessory trim kit is necessary for this installation. Contact your Wolf dealer for details. Remote-mounted control module Internal, in-line and remote blower options Three-speed blower control Filter clean timer lets you know when the filter needs cleaning Delay-off feature automatically turns unit off after five minutes, chimney remains up Stainless steel filter cover with dishwasher-safe aluminum mesh filter LED indicators Downdraft control kit, available as a sales accessory for Models DD30 and DD36 (included with Model DD45)—includes control module, top cover, mounting brackets, RJ45 connector and mounting hardware D O W N D R A F T S Y S T E M F E AT U R E S Model DD36 shown MODEL OPTIONS Downdraft Systems 229 mm chimney elevation Top cover (I) Models 500 CFM internal blower included Three-speed blower control 762 mm Width DD30I 914 mm Width DD36I 1143 mm Width DD45I (R) Models Remote blower required Remote-mounted control module Aluminum mesh filters Stainless steel filter covers 762 mm Width DD30R 914 mm Width DD36R 1143 mm Width DD45R Location of rating plate CONTROL KIT OPTIONS Downdraft Systems ACCESSORIES Downdraft Systems Model DD30I / DD30R Classic Bracket supports for installation of two integrated modules with 762 mm downdraft SRT/Downdraft trim kit for sealed burner rangetop Model ICBSRT304 Transitions in various sizes Accessories are available through your Wolf dealer. 62 DD30CONTROL/S Model DD36I / DD36R Classic DD36CONTROL/S Control module and top cover have the stainless steel finish. Control kits also include mounting brackets, RJ45 connector and hardware and are ordered and shipped as sales accessories for Models DD30 and DD36. Control kit components are included with Model DD45. WOLF COOKTOP VENTILATION PLANNING INFORMATION Wolf downdraft ventilation systems are available in 762 mm, 914 mm and 1143 mm widths. The downdraft should be at least as wide as the cooking surface. Downdraft Model DD30 will fit most 762 mm wide cabinets, Model DD36 will fit most 914 mm wide cabinets and Model DD45 will fit most 1156 mm wide cabinets. It is recommended that oversized cabinets be used for easier installation. Cabinet backs may need to be removed. Specifications on the following pages provide overall dimensions, blower and ducting considerations, and installation specifics for downdraft ventilation systems. Also refer to the cooktop ventilation recommendations on pages 68–69. If a Model DD30 is installed in combination with two integrated modules, an integrated module support for downdraft ventilation is required. Contact your Wolf dealer for information on accessory components. IMPORTANT NOTE: To install a downdraft system and a Wolf cooktop, you must allow for a minimum 638 mm flat counter space from front to back. A countertop with a raised lip and/or backsplash may not allow enough space for proper installation. 60 mm of flat countertop is required behind the cooktop and 44 mm is necessary between the back edge of the cooktop and inside of cabinet back. I N S TA L L AT I O N Refer to installation instructions shipped with each Wolf product for detailed specifications. IMPORTANT NOTE: This appliance must be used with a Wolf-approved control module and top cover. The remote-mounted control module is available as a sales accessory for Models DD30 and DD36 and is included with Model DD45. Installation of the control module must be within 3 m of the downdraft assembly and a minimum of 102 mm from the outer edge of cooktop element or burner. You will be required to drill three holes and connect the downdraft to the control module with the provided wire. OVERALL DIMENSIONS Downdraft Systems Models DD30I / DD30R 762 mm Models DD36I / DD36R 230 mm 230 mm 819 mm 667 mm 1156 mm 60 mm 914 mm 60 mm Models DD45I / DD45R 38 mm 38 mm DEPTH OF DOWNDRAFT CHIMNEY DEPTH OF DOWNDRAFT CHIMNEY 230 mm 60 mm 1048 mm 38 mm DEPTH OF DOWNDRAFT CHIMNEY 63 WOLF COOKTOP VENTILATION I N S TA L L AT I O N S P E C I F I C AT I O N S Downdraft Systems S P E C I F I C AT I O N S Models DD30I / DD30R Overall Width 762 mm Overall Height (above countertop) 230 mm Overall Depth 60 mm Duct Size (DD30I) 83 mm x 254 mm Duct Size (DD30R) 83 mm x 356 mm Discharge Adjustable Blower (DD30I) 500 CFM Internal Blower Options* (DD30R) 1100 CFM In-Line, 900, 1200 or 1500 CFM Remote Electrical Supply 220-240 V AC, 60 Hz 15 amp dedicated circuit Power Cord .8 m 3-prong Shipping Weight 34 kg 638 mm min 44 mm min BACK EDGE OF COOKTOP TO INSIDE OF CABINET BACK* OF FLAT COUNTERTOP* 16 mm 8.7 mm 489 mm 64 mm min COOKTOP CUT-OUT DEPTH WITH NO RAISED LIP* 60 mm 197 mm 54 mm 83 mm 745 mm COUNTERTOP TO BOTTOM OF AIR BOX 92 mm 127 mm 914 mm 457 mm S P E C I F I C AT I O N S Models DD36I / DD36R Overall Width 914 mm Overall Height (above countertop) 230 mm Overall Depth 60 mm Duct Size (DD36I) 83 mm x 254 mm Duct Size (DD36R) 83 mm x 356 mm Discharge Adjustable 181 mm 610 mm min CABINET DEPTH *AREAS OF POTENTIAL INTERFERENCE Blower (DD36I) 500 CFM Internal Blower Options* (DD36R) 1100 CFM In-Line, 900, 1200 or 1500 CFM Remote Electrical Supply 220-240 V AC, 60 Hz 15 amp dedicated circuit Power Cord .8 m 3-prong Shipping Weight 36 kg 70 mm 686 mm FOR MODEL DD30 838 mm 638 mm min FOR MODEL DD36 FLAT COUNTERTOP SPACE FOR MODEL DD45 1067 mm 489 mm COOKTOP CUT-OUT WIDTH 64 mm min COUNTERTOP TOP VIEW S P E C I F I C AT I O N S Models DD45I / DD45R Overall Width 1156 mm Overall Height (above countertop) 230 mm Overall Depth 60 mm Duct Size (DD45I) 83 mm x 254 mm Duct Size (DD45R) 83 mm x 356 mm Discharge Adjustable Blower (DD45I) 500 CFM Internal Blower Options* (DD45R) 1100 CFM In-Line, 900, 1200 or 1500 CFM Remote Electrical Supply 220-240 V AC, 60 Hz 15 amp dedicated circuit Power Cord .8 m 3-prong Shipping Weight 39 kg *Refer to the cooktop ventilation recommendations on pages 68–69. 64 WOLF COOKTOP VENTILATION ELECTRICAL REQUIREMENTS BLOWER CONSIDERATIONS Wolf downdraft ventilation systems require a separate, grounded 120 V AC, 60 Hz power supply. The service should have its own 15 amp circuit breaker, and a grounded 3-prong receptacle should be located within the reach of the .8 m power cord. The specific location of the outlet is not critical as long as it is within reach of the power cord that is located midway, top and bottom, on the right side of the downdraft. Except for Models DD30I, DD36I and DD45I, which include a 500 CFM internal blower, Wolf downdrafts are shipped without the blower assembly. In-line and remote blower assemblies are available. The blower will vary in size and is dictated by the cooking surface, the volume of air that needs to be moved and the length of the duct run. A straight, short duct run with a limited number of elbows and transitions will allow the ventilation hood to perform most efficiently. IMPORTANT NOTE: If Model DD30 is to be installed in a 762 mm wide cabinet, Model DD36 in a 914 mm wide cabinet or Model DD45 in a 1156 mm wide cabinet, the electrical outlet cannot be located on the back wall of the cabinet. The outlet may be placed in adjacent cabinetry. Locate electrical within the shaded area shown in the Installation Specifications illustrations. IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. You must follow all local codes and ordinances when installing your service. Wolf downdraft ventilation systems are designed for use with 83 mm x 254 mm ductwork for Models DD30I, DD36I and DD45I and 83 mm x 356 mm ductwork for Models DD30R, DD36R and DD45R. Each can be transitioned to 203 mm or 254 mm round ductwork. I N S TA L L AT I O N Refer to installation instructions shipped with each Wolf product for detailed specifications. A remote-mounted blower will minimize the amount of blower noise, but will not eliminate the noise completely. IMPORTANT NOTE: Install this downdraft system only with a Wolf blower. Refer to the cooktop ventilation recommendations on pages 68–69. I N S TA L L AT I O N S P E C I F I C AT I O N S Location of Electrical Supply 610 mm min 102 mm min 89 mm E E 254 mm CABINET DEPTH 762 mm min FOR MODEL DD30 914 mm min FOR MODEL DD36 1156 mm min FOR MODEL DD45 OPTIONAL ELECTRICAL LOCATION IN ADJACENT RIGHT SIDE CABINET IMPORTANT NOTE: Certain installations may require that the electrical supply be placed in an adjacent cabinet within reach of the power cord. Choose the location shown in the illustration that best suits your installation. 65 WOLF COOKTOP VENTILATION DUCTING CONSIDERATIONS Wolf downdraft systems have an adjustable discharge that will allow you to negotiate ducting around floor joists and other obstacles. Three different discharge locations are available with side-to-side adjustment for accurate alignment of ductwork. Refer to the illustration below for discharge location and adjustment. Choose the ducting option that allows the shortest length of ductwork and a minimum number of elbows and transitions. Refer to the illustration below for ducting options. IMPORTANT NOTE: All Wolf downdraft systems must be vented to the outside. Use only metal ductwork. For best performance, 254 mm round ductwork is recommended. The downdraft will operate most efficiently when ductwork does not exceed 12 m in length. D I S C H A R G E L O C AT I O N DUCTING OPTIONS Downdraft Systems Downdraft Systems 416 mm CENTERLINE OF COUNTERTOP CUT-OUT INTERNAL BLOWER 546 mm IN-LINE OR REMOTE BLOWER CL 254 mm ROUND REMOTE BLOWER RIGHT DISCHARGE LOCATION 562 mm INTERNAL BLOWER 483 mm IN-LINE OR REMOTE BLOWER 140 mm INTERNAL BLOWER WALL CAP 108 mm LEFT DISCHARGE LOCATION IN-LINE OR REMOTE BLOWER 305 mm DISCHARGE CUT-OUT DIMENSIONS: MIN TO GROUND 260 mm x 89 mm INTERNAL BLOWER INTERNAL BLOWER INSTALLATION THROUGH WALL 362 mm x 89 mm REMOTE BLOWER ROOF MOUNT INSTALLATION IN-LINE OR REMOTE BLOWER CENTERLINE OF COUNTERTOP CUT-OUT REMOTE BLOWER CL ADJUSTMENT: 254 mm ROUND 25 mm – 178 mm INTERNAL BLOWER 165 mm MAX IN-LINE OR REMOTE BLOWER 305 mm ADJUSTMENT: 140 mm 127 mm MAX INTERNAL BLOWER IN-LINE OR REMOTE BLOWER BOTTOM DISCHARGE LOCATION 305 mm MIN TO GROUND 108 mm IN-LINE OR REMOTE BLOWER NOTE: Measurements are to centerline of duct cut-outs 66 MIN TO GROUND INTERNAL BLOWER INSTALLATION THROUGH WALL REMOTE BLOWER INSTALLATION THROUGH WALL WOLF VENTILATION RECOMMENDATIONS WOLF BLOWER ASSEMBLIES A ventilation system must include a blower assembly. An internal, in-line or remote blower assembly must be selected to accommodate the cooking appliance, CFM requirements and homeowner preferences. Internal, in-line and remote blower assemblies are available as sales accessories through your Wolf dealer. Remote blowers can be mounted on the roof or, in some cases, on an exterior wall. A remotemounted blower will minimize the amount of blower noise but will not eliminate the noise completely. Internal blowers are mounted inside the hood canopy or downdraft blower box. Cooktop ventilation recommendation charts on pages 68–69 provide minimum CFM recommendations according to the cooking appliance and ventilation system used and blower options for each specific downdraft. Wolf internal, in-line and remote blowers are for use with Wolf downdraft systems. Wolf in-line blowers are mounted between the downdraft and the exterior of the home. Ducting runs from the downdraft and connects to the blower. More ducting is attached to the other side of the blower and runs to the exterior of the home. An in-line blower is a good option for those who do not want the blower mounted inside the downdraft but cannot, or prefer not to, mount a remote blower on the exterior of the home. Refer to the illustrations below for dimensions of Wolf in-line and remote blowers. Installation instructions shipped with each Wolf ventilation product provide detailed specifications. These instructions can also be found on our website, wolfappliance.com. IN-LINE BLOWER ACCESSORIES Blower assemblies are available through your Wolf dealer. REMOTE BLOWERS 533 mm 632 mm 718 mm 457 mm 305 mm 203 mm 749 mm 254 mm Diameter 394 mm 559 mm 254 mm 527 mm 375 mm 622 mm 121 mm 629 mm BLOWER-110IL 749 mm 264 mm 356 mm 457 mm 254 mm Diameter BLOWER-60REM and BLOWER-90REM 635 mm 184 mm BLOWER-150REM 457 mm 254 mm 749 mm 254 mm Diameter 375 mm 749 mm 257 mm 559 mm 184 mm BLOWER-120REM 67 WOLF VENTILATION RECOMMENDATIONS COOKTOP VENTILATION CFM RECOMMENDATIONS DOWNDRAFTS DD30 DD36 DD45 Electric Cooktops Model ICT15E 215* Model ICT30E 500 Model ICT36E 150* 350 500 CFM DD30 Recommendations are based on total kW output. Wolf recommends 1 CFM per .03 kW. Additional CFM may be required for charbroilers, griddles and long duct runs. DD36 Model ICBCT15G 215* 150* Model ICBCT30G 500 350 Model ICBCT36G 500 DD30 DD36 DD45 Integrated Modules Model CT15I 215* 150* Model IIM15 215* 150* DD30 DD36 Sealed Burner Rangetops Model ICBSRT304 600 *Use these recommendations to determine total CFM when installing multiple cooktops or modules. 68 DD45 Gas Cooktops DD45 WOLF VENTILATION RECOMMENDATIONS COOKTOP VENTILATION BLOWER OPTIONS DOWNDRAFT SYSTEMS Blower Description 500 CFM Internal Blower Number Downdraft Models Included with (I) Models DD30I / DD36I / DD45I BLOWER-110IL (808332) DD30R / DD36R / DD45R BLOWER-90REM (801641) DD30R / DD36R / DD45R 1200 CFM Remote BLOWER-120REM (801642) DD30R / DD36R / DD45R 1500 CFM Remote BLOWER-150REM (804701) DD30R / DD36R / DD45R 1100 CFM In-Line 900 CFM Remote Adjustable discharge. 83 mm x 254 mm duct for internal blower, no transition required. 83 mm x 356 mm duct for in-line and remote blowers. TRANS-14-10 required for remote blowers. IMPORTANT NOTE Blower configurations are for reference only. Refer to the minimum CFM recommendations for your specific cooking appliance. Consult a qualified HVAC engineer for specific installation and ducting applications. 69 The information and images in this guide are the copyright property of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc. 70 ©Wolf Appliance, Inc. all rights reserved. 71 WOLF APPLIANCE, INC. P O BOX 44848 MADISON, WI 53744 USA WOLFAPPLIANCE.COM 810295 8/ 2007