Transcript
B] Installation Instructions for Side-By-Side Refrigerator To Connect Water Supply Line To Ice Maker Inlet Valve \I This document 1 Pro are The installationSite Your refrigerator is designed to be part of a built-in kitchen cabinet system. Besure to coordinate site preparation and installation with your kitchen contractor. Includethese minimum guidelinesin your site preparation: * Choosea place near a grounded electrical outlet. Do not use an extension cord or an adapter plug. Avoid direct sunlight and close proximity to a range, dishwasher or other heat source. Floorshould be leveland able to support a fully loaded refrigerator. The refrigerator's Ice & Water Dispenser requires water supply access. . Planfor easyaccessto countertops when removingfood. Forcomplete access to drawers and freezer baskets, doors must be able to fully open. Allow the following clearancesfor ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top:3/8 inch Rear. 1 inch 6. Coil excess water supply line (copper tubing and arrange coils so they do not vibrate or 7. Turn ON water supply at shutoff valve and 8. Reconnect refrigerator to electrical power _nly), about 2½ turns, behind refrigerator as shown _ar against any other surface. hten any connections that leak. Jrce. 9. To turn ice maker on, lower wire signal arm ( _ide mounted) or set the ice maker's 0n/0ff power switch to the "l" position (rear mounted). 1 FOAM BLOCK- _SHELF SPACER WiTH TOE GRILL .................... 1 PIECE OF TAPE-- _ i l-- 4P_ECES OFTAPE 4 PIECES OF TAPE I BOX DOOR 3 PIECES OF TAPE-- 3 PIECES OF TAPE-- 2 PIECES OF TAPE_ 5 PIECES OF TAPE-- X 2 PIECES OF TAPE_ _--_P,ECESOFTAPE 4 HECES OF TAPE-- 2 PIECES OF TAPE _ _ AND _--_4 i _ C_--_ . ,---"'t OF DAIRY BINS COMPARTMENT P,ECES OFTAPE _ J_ 1 BOX OF DOOR AND 2 PIECES 7 PIECES HANDLES OF TAPE OF TAPE FOAMOLOCKS Location of these materials may vary depending on your model, 7 Problems?TryThese Suggestions Is the refrigerator's power cord plugged in? Is the refrigerator connected to the household water supply? If you had to remove the refrigerator and freezer doors, did you reattach water and power connectors at the door hinges? (Seethe Use& Care Guide for detailed instructions on removing and replacing doors.) Is the ice maker power switch turned On? Other possibilities to check: Is the power to the receptacle turned on? Is the water filter above the fresh food compartment fully seated (see Use& Care Guide for details)? If you still have operation problems after checking these suggestions, please see the "Solutions To Common Problems" section in your Use & Care Guide. PlaceIn Permanent tuition When using a hand truck: * Load refrigerator from side of cabinet only. Do not run retaining straps over handles. Do not over-tighten retaining straps. Neveruse refrigeratorhandlesto move the refrigerator. * Removetape from doors only after unit is in place. What,s Next.? Congratulations. You are ready to begin enjoying your new Electrolux refrigerator. ConnectWater Su ! LevelRefrigerator & Adjust Doors(if necessary) Before Installing The Water Supply Line, You Will Need: Basic Tools: adjustable wrench, flat-blade screwdriver, and Phillips TMscrewdriver Access to a household cold water line with water pressure between 30 and 100 psi. A water supply line made of 1ginch (6.4ram) OD, copper or stainless steel tubing. To determine the length of tubing needed, measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown). A shutoff valve to connect the water supply line to your household water system. DO NOTuse a self-piercing type shutoff valve. To install toe grille '½.,oo,o,,oo_%,_o,,,,o -_ !io.o ._,_ "_ _ lower hinges of refrigerator. While pushing toe grdle binet, fasten Open both doors. Slide firmly left andagainst right es of toe grillebottom over clips of toe grille to cabinet. 3 Fasten top clips to cabinet. 4 Close the doors. Fasten right and left side clips into groove of bottom hinge. To remove toe grille 1 With both doors closed, unfasten right and left side clips of toe grille from bottom hinge grove. 2 Open both doors. Press firmly on top of toe grille until top of toe grille pops off. 3 Pull toe grille outward towards your bod_ .nd off of lower hinges. NOTE: Level the unit with the adjustable rollers _fore leveling the doors. To level the doors using the adjustable lower hinge (some models): _i 1 Before leveling either door, remove set screw that locks door height into posi- _1I_li °_'_ T tion. (The door cannot be adjusted without set screw removed.) _ T EtCh/ 2 If the refrigerator door is lower than the freezer door, raise the refrigerator door by turning the adjustment screw counterclockwise using a 7/l_inch wrench. (See iflustration.) 3 If the freezer door is lower than the refrigerator door raise the freezer door byturningthe adjustment screw counterclockwise _1 ..................... using a 7/_ inch wrench. (See dlustration.) ..... _!_,!:_!!_!_i ........................ ,_*::;:::: ........................................ 4 After leveling, verify door stop contacts lower hinge and top of door i:_; 2 1 A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice maker inlet valve. with the installation in Materials Operation problems are possible if any of the installation tasks are not completed. Here is a list of things to check for: By now, you have already removedyour refrigerator's shipping carton.You rnaystill need to use a hand truck to move it through closespaces or entrances. If the refrigerator is largerthan an entrance, consider two options: Removethe entrance door if one exists. Removethe refrigeratordoors (see how in your Use& Care Guide). Not satisfied after installation. iiii_iiiii_i_!i!_ii_i_i!iiii_ili!_!!iii_i_i!iii!_ili _I_I _ii!i!ii!i!_i;iiii_iiiii_iiiii_iiiiiiiii!iiiii_!iiii!!i;!!i_i_i _i_i_i _i_ii_i;!_iiiiii_i!ii!i_i_!iiiii!i!iiii_iii_i!!i ,iii!i_iii!_i:i_i!iiiiii!;ii_!ili;iiii!_!ii!i!_!_i;i!i _i_i_:_:!_!_i!_i_i!_i_i_:i_i_!i_i_!_i_i_i_!_!;!_ii_i_!i_i_!_;_i!i!_:!_!i!_!i_;iii_!i_;_!i_;_!i_;i!_i_!_!!!i_!!;!_:_!_i_!_!JJii_!i!i_!i_i_!_!!i_i!i_!i_!_i_ii!_!!_!i_i;i_!!ii _i _i_i:!ii!iii_i!i!_i:ii!_i_i!ii_i!iii_i!i_i!iiii_ill _i_iiii_i:i!i_!,!i!_!,!i_!_i_i_!i!ii Trans ort Un acka ed Refri orator To Site * by customer Electrolux uses packing foam and tape to secure the internal parts of your refrigerator for shipping. Once the refrigerator is in position, you can remove this material. SOUrCe, 2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFFwater supply at shutoff valve. _at_ Vak,e 3. Remove plastic cap from water valve inlet and discard cap. 4. If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto t (it;elude erlough _ubir;9 it; _op m alk_w water supply line. Push water supply line into water valve inlet as far as it will go (1Ainch/6.4 mm). Slide ferrule (sleeve) into alve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 1. If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and finger ghtencompression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 2. 5. With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown. Necessary: only be removed RemoveInternal Shi Z 1. Disconnect refrigerator from electric power Tools should 5 of your refrigerator? does closed not contact hinge through full movement of door (from fully to fullyupper open). Replace the toe grdle by fitting it into _ ce. % '_'i i L> Please contact the store you purchased it from. * To become aware of important safety instructions and learn how to operate your refrigerator, please read the entire Use & Care Guide. * You may want to start with the "Normal Operating Sights & Sounds" section of the Guide to learn more about what to expect during typical operation. Pleaseregister your product. You can register online at www.electroluxusa.com, or you can simply send in the Registration Card. Andthankyou for choosingElectro/ux. 9 I--4In II i n h k ff Li Doors ice Maker E]Handles are secure and tight E]Door seals completely to cabinet on all sides E]Freezerdoor is level across the top E]House water supply connected to refrigerator E]No water leaks present at all connections recheck in 24 hours E]lce Maker is turned ON E]lce & Water Dispenser operates correctly E]Front filter must be flush with filter housing (some models) Leveling E]Refrigerator is level,side to side and tilted W' (6ram) front to back E]Toegrille is properly attached to refrigerator DCabinet is setting solid on all corners Electrical Power E]House power turned on E]Refrigerator plugged in Final Checks E]Shipping material removed E]Fresh Food and Freezer temperatures set E]Crisper Humidity controls set E]Registration Card sent in
