Download Sharp LL-153A Service manual
Transcript
15” LCD Color Monitor Sharp LL-153A Service Service Service Horizontal Frequency 30kHz –80kHz TABLE OF CONTENTS Description Page Description Page Table Of Contents.......……..……..........................…........1 6. Schematic……………....................................…17 Revision List.….............……..........................……......2 6.1 Main Board.……...……..........................................17 Important Safety Notice.…………....................……......3 6.2 Inverter Board..………..……..................................22 1. Monitor Specification..............................………........4 6.3 Adapter Board...………..…….................................23 2. LCD Monitor Description…………………………….......5 6.4 Audio Board...………....…….................................24 3. Operation Instruction…………...............……...........6 7. PCB Layout..…….………….......................................25 3.1 General Instructions...........................…...........6 7.1 Main Board…………….........................................25 3.2 Control Button…………….…..............……...............6 7.2 PWPC Board…..………....................................26 3.3 Adjusting the Picture...........................…............7 7.3 Audio Board……….……….....................................27 4. Input/Output Specification............………..……............8 7.4 Key Board……………….....................................28 4.1 Input Signal Connector............………….................8 8. Maintainability……….......................................28 4.2 Factory Preset Display Modes..........................9 8.1 Equipments and Tools Requirement……..............28 4.3 Power Supply……..………………………….………….10 N 8.2 Trouble Shooting…….………..............................29 4.4 Panel Specification.....………………………................10 9. White-Balance, Luminance adjustment.............34 5. Block Diagram……...................…………................13 10. Monitor Exploded View……….……………............36 5.1 Soft Flow Chart….………………..……..……....….......13 11. BOM List……….....................................................37 5.2 Electrical Block Diagram….……………..…........….….15 SAFETY NOTICE ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING 1 15” LCD Color Monitor Sharp LL-153A Revision List Revision Date Revision History TPV Model A00 Dec-28-06 Initial Release T56CM5NJXXXWAJ 2 15” LCD Color Monitor Important Safety Notice Sharp LL-153A Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service procedures recommended by AOC and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended. It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected. Hereafter throughout this manual, AOC Company will be referred to as AOC. WARNING Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock, fire, or other hazards. Under no circumstances should the original design be modified or altered without written permission from AOC. AOC assumes no liability, express or implied, arising out of any unauthorized modification of design. Servicer assumes all liability. FOR PRODUCTS CONTAINING LASER: DANGER-Invisible laser radiation when open AVOID DIRECT EXPOSURE TO BEAM. CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION -The use of optical instruments with this product will increase eye hazard. TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF THIS SERVICE MANUAL. Take care during handling the LCD module with backlight unit -Must mount the module using mounting holes arranged in four corners. -Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen. -Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to the panel. -Protect the module from the ESD as it may damage the electronic circuit (C-MOS). -Make certain that treatment person’s body is grounded through wristband. -Do not leave the module in high temperature and in areas of high humidity for a long time. -Avoid contact with water as it may a short circuit within the module. -If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may damage the panel.) 3 15” LCD Color Monitor Sharp LL-153A 1. Monitor Specifications Items Descriptions Driving system TFT Color LCD Type CPT CLAA150XP01Q Size 38cm(15.0") Pixel pitch 0.297mm(H) x 0.297mm(V) Viewable angle 140˚ (H) 125˚ (V) Response time (type) 8 ms for CPT panel Video R, G, B Analog input Digital input Sync. Type H/V TTL H-Frequency 24.8kHz – 80kHz V-Frequency 56-75Hz ON Mode ≤27W OFF Mode ≤1W LCD Panel Input Power Consumption Contrast Ratio 500:1 Dot Clock 135MHz White Luminance 250cd/m2 Max. Resolution 1024 × 768 @75Hz Power Consumption (Maximum) 27 Watts Display Color 16 M (6-bits+FRC) Plug & Play VESA DDC2BTM Input Connector 15-pin D-Sub Maximum Screen Size Horizontal: 304.1mm;Vertical: 228.1mm Power Source 100~240VAC,47~63Hz Environmental Considerations Operating Temp: 5°C to 35°C Storage Temp: -20°C to 60°C Operating Humidity: 10% to 85% 4 15” LCD Color Monitor Sharp LL-153A 2. LCD Monitor Description The LCD MONITOR will contain a main board, a power board and a keypad board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage. Monitor Block Diagram Flat Panel and CCFL Drive. CCFL backlight PWPC board main board (Include: adapter, inverter) RS232 Connector For white balance adjustment in factory mode Keyboard AC-IN HOST Computer 100V-240V 5 Video signal, DDC 15” LCD Color Monitor Sharp LL-153A 3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. • Press the power button to turn on the monitor position. The power indicator will light up. 3.2 Control Buttons - Power Button: When pressed, the monitor enters the off mode, and the LED turns blank. Press again to restore normal status. - Left / Right Button: The Left/Right Button is used to control the monitor functions. Press to switch functions or adjust settings. - /MODE: The /MODE Key is used to move the cursor and select display mode. - Power Indicator: Green — Power On mode. Red — Power Saving mode. Blank —Power Off Mode. LED = GREEN, BLINKING (0.5s period) —Out of Range OSD Menu Volume/Bright +, & Menu Select Move the Cursor and Select Display Mode NO. Name 1 MENU 2 /MODE 3 < 4 > 5 POWER 6 Indicator Light Indicator Light Power On/Off Within OSD An adjustment menu display, a change, elimination Without OSD Activate OSD main menu Select display mode to STD or OFFICE or sRGB or VIVID. 1.Move the cursor to left Activate the volume and the bright 2. Decrease the value of the selected item menu 1.Move the cursor to right Activate the volume and the 2.Increase the value of the selected item brightness menu Move the cursor to down Power On / Off Green—On Power On / Off Red—Save 6 Green—On Red—Save 15” LCD Color Monitor Sharp LL-153A 3.3 Adjusting the Picture 1. Press the MENU-button to activate the OSD window. 2. Press < or > to select the desired function. 3. Press the / MODE -button to select the function that you want to adjust. 4. Press < or > to change the settings of the current function. 5. To exit and save, select the exit function, or leave the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4. CONTROL FUNCTION Main Menu Sub Main Menu Description Adjust picture Clock to reduce Vertical-Line noise. Adjust Picture Phase to reduce Horizontal-Line noise. Adjust the horizontal position of the picture. Adjust the vertical position of the picture. Clock Phase H. Position V. Position Black Level Adjust the black level of the picture. Contrast Contrast from Digital-register. Cool Recall cool Color Temperature from EEPROM. STD Recall standard Color Temperature from EEPROM. Warm Recall warm Color Temperature from EEPROM. White Balance User OSD H-Position OSD V-Position Scaling 7 Adjust the value of the Red/Green/Blue user color temperature. Adjust the horizontal position of the OSD. Adjust the vertical position of the OSD. Adjust the sharpness of the pictures. English Set OSD display language to English. Español Set OSD display language to Spaish. Français Set OSD display language to French. 中文 Set OSD display language to Chinese. 日本语 Set OSD display language to Japanese. 15” LCD Color Monitor Sharp LL-153A Information Show the model, the S/N and the Usage time. Off The off timer is off On The off timer is on 4. Input/Output Specification 4.1 Input Signal Connector D-SUB connector Pin No. Description Pin No. Description 1. Red Video 9. +5V Supply 2. Green Video 10. GND 3. Blue Video 11. NC 4. NC 12. DDC-Serial Data 5. GND 13. H-Sync 6. Red Ground 14. V-Sync 7. Green Ground 15. DDC-Serial Clock 8. Blue ground Analog Connector 1 5 6 10 11 15 8 15” LCD Color Monitor Sharp LL-153A 4.2 Factory Preset Display Modes 4.3 Power Supply The power supply should be integrated to the monitor housing. A/C Line voltage range : 100 V ~ 240 V A/C Line frequency range : 50 ± 3Hz, 60 ± 3Hz Current : 1.5A max at 100V; 0.8A max at 240 V Peak surge current : < 55A peak at 240 VAC and cold starting Leakage current : < 3.5mA Power line surge : No advance effects (no loss of information or defect) With a maximum of 1 half-wave missing per second DC output Voltage Current : 5VDC ± 5%; 12VDC± 5% 1.5Amp (5V) ;2 Amp (12V) 9 15” LCD Color Monitor Sharp LL-153A 4.4 Panel Specification 4.4.1 Display Characteristics 10 15” LCD Color Monitor Sharp LL-153A 4.4.2 Optical Characteristics 4.4.3 Electrical Characteristics TFT LCD Module 11 15” LCD Color Monitor Sharp LL-153A Back- Light Unit 12 15” LCD Color Monitor Sharp LL-153A 5. Block Diagram 5.1 Soft Flow Chart 1 Y 2 3 N 4 N 5 Y 6 N 7 8 Y 9 N 10 11 Y N 12 13 Y Y 14 15 Y 17 18 N N 19 Y 13 N 16 15” LCD Color Monitor Sharp LL-153A 1) MCU initializes. 2) Is the EPROM blank? 3) Program the EPROM by default values. 4) Get the PWM value of brightness from EPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode. 9) Save the power key status into EPROM. Turn on the LED and set it to green color. Scalar initializes. 10) In standby mode? 11) Update the lifetime of back light. 12) Check the analog port, are there any signals coming? 13) Does the scalar send out an interrupt request? 14) Wake up the scalar. 15) Are there any signals coming from analog port? 16) Display "No connection Check Signal Cable" message. And go into standby mode after the message disappears. 17) Program the scalar to be able to show the coming mode. 18) Process the OSD display. 19) Read the keyboard. Is the power key pressed? 14 15” LCD Color Monitor Sharp LL-153A 5.2 Electrical Block Diagram 5.2.1 Main Board LCD Interface Flash memory Scalar TSUM13AK (Include:ADC,OSD,MCU etc.) EPR_SDA EPR_SCL OSD Control Interface (Key pad) RXD TXD RGB H-SYNC V-SYNC D-Sub Connector EEPROM 24C16 DB15_SDA DB15_SCL EEPROM 24C02 15 Crystal 14.31818MHz 15” LCD Color Monitor Sharp LL-153A 5.2.2 Inverter/Power Board AC input Bridge Rectifier and Filter EMI filter Rectifier diodes Transformer 12V Start Circuit: R909、R910、R931 CN902 12V Feedback Over Voltage Protect PWM Control IC 5V Circuit ON/OFF Output Lamp MOSFET Q805 Transformer Circuit PWM Feedback Circuit PWM Control IC ON/OFF Control DIM 16 15” LCD Color Monitor Sharp LL-153A 6. Schematic 6.1 Main Board TSUM13AK XGA/SXGA B3 SCHEMATIC LVDS OUTPUT B4 RIN GNDR GIN GNDG SOG BIN GNDB HSY NC VSY NC DDCA_SDA DDCA_SCL DET_VGA +5V +5V RIN GNDR GIN GNDG SOG BIN GNDB HSY NC VSY NC DDCA_SDA DDCA_SCL DET_VGA VCC1.8 +3V3 +5V +12V VCC1.8 DDC_WP DDC_WP +3V3 +5V +12V 3.INPUT B5 PA[0..7] PA[0..7] PA[0..7] +3V3 PA[12..13] PA[12..13] PA[12..13] +12V PB[12..21] PB[12..21] PB[12..21] +3V3 VLCD VCC1.8 +5V VLCD B2 on_BACKLIGHT on_Panel +3V3 on_BACKLIGHT on_Panel +12V 5.PANEL INTERFACE VCC1.8 +5V Adj_BACKLIGHT +3V3 Adj_BACKLIGHT VLCD VLCD Title 4.SCALER TSUM13AK Size B 2.POWER Date: 17 Document Number Rev A TOP Monday , May 30, 2005 Sheet 1 of 5 15” LCD Color Monitor Sharp LL-153A +3V3 +3V3 +5V Q602 AO3401L (3,4,5) AIC1084-18PM TO-263 layout together L602 22uH 3 2 PGATE C610 + D602 1 C604 100uF/25V 0.1uF C609 220uF/25V + U601 LM3485 7 C613 0.001uF 6 5 VIN PGATE VIN VOUT VCC1.8 (4) ADJ C602 47uF/25V + 47uF/25V C603 0.1uF 3 N.C 2 PWGND AGND ADJ 1 + 2 C614 0.001uF 4 FB C601 C612 0.001uF SSM54 8 R606 33K 1/16W R605 22 1/16W VCC1.8 U602 3 R607 1 ISENSE C611 0.001uF 33K 1/16W 1% R608 20K 1/16W keep shorter keep away from L602 +5V +12V +12V C706 0.1uF 100uF/25V 5V +5V FUSE_1.5A GND (4) CN701 1 3 5 7 9 11 10K 1/16W BL_ON BL_ADJ +12V GND 5V GND 2 4 6 8 10 12 R710 C711 0.1uF F602 C709 C710 + 0.1uF 100uF/25V R711 (3,4) +5V TO-263 10K 1/16W R712 4.7K 1/16W U702 on_BACKLIGHT (4) 3 Q703 PMBS3904 1 CONN +3V3 C702 +5V + NC R701 C713 VIN PANEL3.3 VOUT 2 ADJ NC NC C712 C714 + NC NC +3V3 +5V 1K 1/16W R703 NC NC R706 NC R705 4.7K 1/16W +3V3 R715 R702 0 1/16W Q701 (4) Adj_BACKLIGHT R707 1K 1/16W PMBS3904 NC VLCD PANEL3.3 VLCD C708 1uF/25V R716 NC R717 R714 4.7K 1/16W 10K 1/16W R731 1K 1/16W +3V3 (5) C701 NC Q704 AO3401L R723 51K 1/16W FB414 NC FB413 120 OHM 3 120 OHM FB701 GND GND +12V GND +5V (4) on_Panel R725 NC 1 C718 NC Q706 NC 2 (3,4) C707 + +5V R708 C715 NC + C717 47uF/25V Title TSUM13AK Size B Date: 18 Document Number Rev A POWER Wednesday , June 01, 2005 Sheet 2 of 5 Sharp LL-153A CN405 RED+ REDGREEN+ GREENBLUE+ BLUE- 75 1/16W R440 75 1/16W R438 VGA_CON 56 1/16W C432 0.047uF R435 56 1/16W C433 0.047uF R436 56 1/16W C434 0.047uF R437 470 1/16W C435 0.001uF R441 100 1/16W C436 0.047uF R442 100 1/16W C437 0.047uF R443 100 1/16W C438 0.047uF D404 BAV99 RIN (4) GIN (4) BIN (4) SOG (4) GNDR (4) GNDG (4) GNDB (4) +5V PC5V D405 BAV99 ESD_5V C440 0.1uF C441 0.1uF +5V 1 C439 0.1uF 1 R470 UDZS5.6B 2 ZD403 +5V D403 BAV99 3 DB15 3 16 15 FB412 0 1/16W PC5V PC5V 2 14 R434 FB411 0 1/16W 3 13 FB409 0 1/16W R439 75 1/16W 1 6 2 7 3 8 4 9 5 10 12 1 11 2 17 15” LCD Color Monitor +5V 1K 1/16W (2,4) R444 NC R445 NC ZD404 DET_VGA (4) VSI 0 1/16W 2 100 1/16W R455 R446 150 1/16W R486 R447 1K 1/16W D407 R451 4.7K 1/16W ZD402 UDZS5.6B UDZS5.6B R448 2.2K 1/16W C442 47pF R449 2.2K 1/16W C443 R450 220pF R452 NC R453 R454 C444 U201 8 7 6 5 4.7K 1/16W SCL_VGA SDA_VGA 100 1/16W 100 1/16W VCC A0 WP A1 SCL A2 SDA VSS 1 2 3 4 1uF/25V UDZS5.6B (4) (4) DDCA_SDA DDCA_SCL DDC_WP (4) +3V3 R480 0 1/16W C113 2 13 12 U202F NC 4 7 3 0.1uF VCC VSY NC (4) 14 U202A NC 14 1 0 1/16W 14 14 R494 GND 11 120 OHM FB407 U202E NC 10 HSY NC (4) R493 7 NC U202B 7 7 ZD406 UDZS5.6B M24C02WMN6 ZD405 ZD401 100 1/16W BAV70 3 HSI 1 UDZS5.6B ZD412 ESD_5V 0 1/16W GND Title TSUM13AK Size B Date: 19 Document Number Rev A INPUT Tuesday , May 31, 2005 Sheet 3 of 5 15” LCD Color Monitor VDVI Sharp LL-153A VMPLL VPLL AVDD VDDP VDDC +5V 0.1uF 61 REFP GB1P/NC/GB2 GB1N/NC/GB3 GB2P/NC/GB4 GB2N/NC/GB5 GB3P/NC/GB6 GB3N/NC/GB7 REFM +3V3 TSUM13AK U402 8 7 3 4 C417 1uF/25V ROM_WP# VDD HOLD# WP# VSS SDO CE# SCK SDI 2 1 6 5 70 71 72 73 CLKBP/LVBCKP/LCK_ODD CLKBN/LVBCKM/LDE NC/LVB2P/NC NC/LVB2M/NC BB1P/LVB1P/BB2 BB1N/LVB1M/BB3 BB2P/LVB0P/BB4 BB2N/LVB0M/BB5 BB3P/NC/BB6 BB3N/NC/BB7 SST25VF010-33 RST 19 CLKAP/LVB3P/LHSY NC RSDS/LVDS/TTLCLKAN/LVB3M/LVSY NC SDO SCZ SCK SDI RST R482 10K 1/16W C421 22pF 32 ESP OSP GPO0 GPO1 GPO2 GPO3 GPO4 GPO5 GPO6 XIN X401 14.318MHz 33 C423 22pF XOUT GPIO_P22 GPIO_P23 GPIO_P03 +3V3 R407 R410 NC NC 102 104 R415 GPIO_P16 GPIO_P15 PWM2/GPIO_P24 GPIO_P27/PWM1 MODE[0] MODE[1] GPIO_P16 PWM1/GPIO_P25 R416 10K 1/16W GPIO_P17/SAR0 GPIO_P00/SAR1 GPIO_P01/SAR2 GPIO_P02/SAR3 10K 1/16W GPIO_P06 GPIO_P07 PWM0/GPIO_P26 GPIO_P13 GPIO_P14 GND GND GND GND GND GND DDCROM_SCL DDCROM_SDA +3V3 (2,3,5) +3V3 2 3 5 6 7 8 118 119 120 121 122 123 124 125 126 127 128 1 PB12 PB13 PB14 PB15 PB16 PB17 PB18 PB19 PB20 PB21 R405 NC R489 NC R481 100 1/16W 1 C422 R490 +3V3 +5V R412 NC on_BACKLIGHT (2) adj_BACKLIGHT (2) R413 Q403 PMBS3906 C425 R426 U303 10K 1/16W 8 VCC R427 100 1/16W 7 WP 100 1/16W 6 SCK 100 1/16W 5 SI 1uF/25V A0 A1 A2 VSS 1K 1/16W +12V R431 NC R433 1K 1/16W NC R457 1K 1/16W R456 Volume OUT-L+ OUT-L- FUSE_2A +12V R488 R474 R475 10K 1/16W R476 10K 1/16W 10K 1/16W R477 10K 1/16W KEY _AUTO1 R418 1K 1/16W KEY _AUTO KEY _RIGHT1 R420 1K 1/16W KEY _RIGHT KEY _MENU1 R483 1K 1/16W KEY _MENU KEY _LEFT1 R484 1K 1/16W KEY _LEFT LED_G LED_A KEY _POWER C427 0.1uF C428 0.1uF C430 0.1uF C429 0.1uF C446 0.1uF C447 0.1uF (2) AUDIO_STBY R495 10K 1/16W R496 10K 1/16W AUDIO_MUTE CN403 OUT-R+ OUT-R- PMBS3904 Q405 R458 Q404 F601 +3V3 10K 1/16W 1 2 3 4 0.1uF 0 1/8W LED_A 0 1/16W LED_G 0 1/16W +5V +3V3 R485 R419 PMBS3906 R421 +5V 100 1/16W 100 1/16W Q401 Volume AUDIO_MUTE AUDIO_STBY R425 R409 NC C426 CN404 2 4 6 8 10 12 14 R408 10K 1/16W R414 C424 NC KEY _POWER1 R411 1 3 5 7 9 11 13 +3V3 10K 1/16W R417 KEY _RIGHT1 KEY _MENU1 KEY _LEFT1 4.7K 1/16W 4.7K 1/16W (2,3) DET_VGA (3) on_PANEL (2) 22 23 24 25 C419 C420 0.1uF 0.1uF DDC_WP (3) +5V ROM_WP# KEY _POWER1 77 76 VMPLL 120 OHM NC M24C16 1K 1/16W C416 NC R406 NC 20 21 R422 R423 FB406 Q402 NC KEY _AUTO1 R428 R429 R430 VPLL 120 OHM +3V3 R424 10K 1/16W FB405 C414 C415 0.1uF 0.1uF +3V3 10K 1/16W 10K 1/16W R479 +3V3 (2,3,5) +3V3 PB[12..21] (5) (2,3,5) +3V3 35 69 78 79 27 28 29 30 31 VDVI 120 OHM 0.1uF PB[12..21] 80 81 88 87 86 85 84 83 82 75 74 26 FB404 ZD414 R478 100K 1/16W REXT UDZS5.6B 62 C401 C409 C410 C411 C412 C413 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF PA[12..13] (5) 9 10 15 16 17 18 ZD413 51 + 10uF/50V UDZS5.6B 390 1% R403 0.1uF (5) ZD410 C448 PA[0..7] UDZS5.6B MAX810STR-2.9V C408 P[0..7] 13 38 41 47 96 116 0.1uF PA12 PA13 89 90 91 92 93 94 ZD411 C445 VDDP UDZS5.6B 12 97 117 68 60 14 67 95 103 115 VDDP VDDP VDDP VDDP VDDP 52 4 34 RB1P/NC/RB2 RB1N/NC/RB3 RB2P/NC/RB4 RB2N/NC/RB5 RB3P/NC/RB6 RB3N/NC/RB7 C407 120 OHM ZD409 AVDD 1 GND AVDD 120 OHM 0.1uF UDZS5.6B RESET Vcc FB403 +3V3 ZD408 3 2 RST 2 BA1P/NC/BA2 BA1N/NC/BA3 BA2P/NC/BA4 BA2N/NC/BA5 BA3P/NC/BA6 BA3N/NC/BA7 +3V3 (2,3,5) UDZS5.6B 1 U405 RX2P RX2N RX1P RX1N RX0P RX0N RXCKP RXCKN DDCD_SDA DDCD_SCL FB402 10uF/50V C404 C405 C406 0.1uF 0.1uF 0.1uF R492 10K 1/16W 39 40 42 43 45 46 48 49 36 37 98 99 100 101 105 106 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 UDZS5.6B 3 (2,3) GA1P/NC/GA2 GA1N/NC/GA3 GA2P/NC/GA4 GA2N/NC/GA5 GA3P/LVA3P/GA6 GA3N/LVA3M/GA7 107 108 109 110 111 112 113 114 +3V3 (2,3,5) +3V3 + C403 10K 1/16W R491 +5V NC/LVACKP/NC NC/LVACKM/NC RA1P/LVA2P/RA2 RA1N/LVA2M/RA3 RA2P/LVA1P/RA4 RA2N/LVA1M/RA5 RA3P/LVA0P/RA6 RA3N/LVA0M/RA7 VDDC 120 OHM ZD407 +5V VCTRL VCC1.8 3 DDCA_SDA DDCA_SCL +5V R487 NC (3) (3) RIN0P RIN0N GIN0P GIN0N SOGIN0 BIN0P BIN0N HSY NC0 VSY NC0 DDCA_SDA DDCA_SCL (2) 11 2 NC 59 58 56 55 57 54 53 63 64 65 66 RIN GNDR GIN GNDG SOG BIN GNDB HSY NC VSY NC VCC1.8 FB401 0.1uF VDDC VDDC VDDC VDD_OTP (3) (3) (3) (3) (3) (3) (3) (3) (3) 1 2 3 4 AVDD_ADC NC AVDD_PLL CN402 AVDD_DVI AVDD_DVI NC U401 AVDD_MPLL AVDD_MPLL R402 44 50 C402 R401 CONN OUT-L+ PMBS3904 F402 FUSE 1A 0603 LED_G KEY _AUTO KEY _LEFT KEY _POWER OUT-L- 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 LED_A KEY _MENU KEY _RIGHT F401 FUSE 1A 0603 OUT-R- OUT-R+ Title TSUM13AK 10K 1/16W GND 20 CONN GND GND Size C Date: Document Number Rev A SCALER Tuesday , May 31, 2005 Sheet 4 of 5 15” LCD Color Monitor (4) PA[0..7] Sharp LL-153A PA[0..7] PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 LVACKP LVACKM LVA2P LVA2M LVA1P LVA1M LVA0P LVA0M +3V3 +3V3 (2,3,4) R728 (4) PA[12..13] PA12 PA13 2.2K 1/16W LVA3P LVA3M LVDS_TEST R729 NC (4) PB[12..21] PB[12..21] PB12 PB13 PB14 PB15 PB16 PB17 PB18 PB19 PB20 PB21 LVB3P LVB3M LVBCKP LVBCKM LVB2P LVB2M LVB1P LVB1M LVB0P LVB0M CN101 R730 LVB0M NC LVB1M LVB2M LVBCKM LVB3M LVA0M LVA1M LVA2M LVACKM LVA3M RXO1RXO2RXOCRXO3RXE0RXE1RXE2RXECRXE3- 1 3 5 7 9 11 13 15 17 19 21 23 RXO0+ RXO1+ RXO2+ RXOC+ RXO3+ RXE0+ RXE1+ RXE2+ RXEC+ RXE3+ 2 4 6 8 10 12 14 16 18 20 22 24 LVB0P LVB1P LVB2P LVBCKP LVB3P LVA0P LVA1P LVA2P LVACKP LVA3P CONN VLCD VLCD C720 0.1uF + C719 47uF/25V (2) R732 1K 1/8W Title TSUM13AK Size B Date: 21 Document Number Rev A PANEL INTERFACE Tuesday , May 31, 2005 Sheet 5 of 5 15” LCD Color Monitor Sharp LL-153A 6.2 Inverter Board RJ801 0 1/8W RJ802 0 1/8W PT801 80GL19T-36-DN 5 7 RJ804 0 1/8W CN801 2 R836 1K 1/10W 3 4 R819 15 1/8W 8 2 C817 5PF/3KV N.C C814 1 33G8021-2D-U R821 100K 1/10W 1000P/50V R820 15K 1/10W 5 G2N D2N R822 3M / 1/2W 2 1 2 N.C R823 75K 1/10W D801 BAV70 D809 LL4148WP + N.C C829 0.1uF/50V Thursday , May 04, 2006 Sheet 2 of 2 R845 1M 1/10W 1M 1/10W R846 R847 1M 1/10W C830 0.1uF/25V R835 C810 470PF/50V C832 C831 0.1uF/25V 0.1uF/25V 1M 1/10W C824 0.1uF/25V R841 430 1/10W 1% R826 430 1/10W 1% C819 0.047UF/25V R817 39K 1/10W C809 0.047UF/50V 1 6 5 G2N D2N S2N D2N G1N D1N C826 5PF/3KV D807 LL4148WP D808 LL4148WP CN803 2 33G8021-2D-U 1 R832 3M / 1/2W 2 33G8021-2D-U 2 1 4 3 7 8 S1N D1N 1 R843 1K 1/10W R848 560 1/10W 3 Rev PWPC1742HDP3P(715G1927 1) R816 1M 1/10W R830 15K 1/10W 3 Date: LL4148WP CN804 R831 100K 1/10W SHARP LL-174A 4 LAMPS INVERTER Document Number D806 8 N.C R840 N.C C815 2 AM9945 C825 10PF/3KV 1 1000P/50V Q806 Size C808 6800PF/50V R814 56K 1/10W C820 470UF/25V 33K 1/8W AOC (Top Victory) Electronics Co., Ltd. Q810 RK7002 C827 470PF/50V J825 TIN COATED Q809 RK7002 C821 0.1uF/25V 2 J824 TIN COATED J821 TIN COATED Q808 RK7002 LL4148WP 1 3 4 R829 15 1/8W J823 TIN COATED J820 TIN COATED D805 PT802 80GL19T-36-DN 5 7 C823 1500PF/50V J819 TIN COATED Q807 RK7002 Q804 RK7002 J816 TIN COATED 15 1/8W J818 TIN COATED R837 16 10 1/10W 15 14 13 12 11 10 9 OZ9938 R828 J817 TIN COATED J815 TIN COATED DRV1 PGND VDDA DRV2 TIMER GNDA DIM CT ISEN SSTCMP VSEN LCT OVPT ENA NC1 NC2 C822 1500PF/50V J814 TIN COATED R813 1M 1/10W C805 1000PF/50V C804 1.5uF/25V R811 47K 1/10W C803 0.01UF/50V R812 10K 1/10W J812 TIN COATED R815 100K 1/10W IC801 1 2 3 4 5 6 7 8 C807 0.01UF/50V C806 1UF/25V R810 100K 1/10W 200K 1/10W R842 10 1/10W Title R844 1M 1/10W R809 200K 1/8W J811 TIN COATED D802 BAV99 R827 3.3K 1/10W DIM R808 R825 560 1/10W 3 VCC 1 6 1 3 1 N.C R838 0 1/8W S2N D2N AM9945 R807 22 1/8W +5V 8 Q805 CN802 4 N.C R806 470 1/8W 3 ZD801 RLZ5.6B 33G8021-2D-U C818 470PF/50V N.C R839 33K 1/8W 1 C816 10PF/3KV C813 1500PF/50V VCC S1N D1N C801 0.1uF/50V C812 1500PF/50V 2 1 7 3 2 Q803 PMBS3904 1 G1N D1N Q802 PMBS3904 + C811 470UF/25V 2 1 Q801 PMBS3904 2 R803 10K 1/10W 470 1/8W C828 10K 1/8W 3 ON/OFF R805 0.1uF/50V R804 3 R802 300K 1/8W R818 15 1/8W +12V B 22 D803 BAV70 N.C R833 75K 1/10W R834 3.3K 1/10W D804 BAV99 15” LCD Color Monitor Sharp LL-153A 6.3 Adapter Board 2 R908 680K 1/4W ZD906 NC ! 4 R918 10 1/4W 100KΩ 1% 1/4W L901 R919 10K 1/8W C917 0.001uF ! ! C915 0.1uF/25V RLZ22B NR901 NTCR t F902 ! R915 100 1/8W F901 FUSE ! D903 LL4148WP R913 4.7K 1/8W C916 0.1uF/25V NC CN903 3 ZD904 RLZ12B 1 ZD902 RLZ5.1B R921 3.6K 1/8W DIM R926 1K 1/8W 1 R920 33K 1/8W ON/OFF C918 1uF/25V CN902 CONN 2 4 6 8 10 12 1 3 5 7 9 11 +12V +5V R923 1K 1/8W R925 0 1/8W R924 1K 1/8W R922 2.43K 1/8W AZ431AZ-AE1 C913 3 NC R904 0.68Ω 2W IC903 Q902 PMBS3904 C908 NC R927 100 1/4W PMBS3906 FUSE ! R912 2.7KΩ 1/8W C910 0.1uF/25V CONN(NC) Q901 1 R902 R903 680K 1/4W 680K 1/4W C920 FB901 BEAD 3 2 ! ZD901 C911 470UF/25V 0.001uF/250V 4 R911 4.7K 1/4W + 3 2 1 IC902 PC123X8Y FZOF C903 0.47uF/275V C912 1000uF/25V F801 + ! C919 470pF/25V 3.5uH +5V 2 3 2 R928 220 1/4W ZD903 PTZ7.5B C921 1 2.0MH ! ! SP10150 Q903 2SK2645-54MR ZD905 RLZ18B LD7552BPS C907 0.1uF/25V 2 1 R930 D904 2 ! 5 6 7 8 + C906 470UF/25V L904 C932 0.001uF + POWER X'FMR 1 C901 0.001uF/250V ! RT NC VCC CS COMP VCC GND OUT + C909 1000uF/25V 11 R932 680K 1/4W U? 4 3 2 1 R937 100 1/4W 7 2 VAR901 Varistor +12V + C904 NC R916 100 1/4W R936 100 1/4W 6 C922 22uF/50V 1 R931 430K 1/4W 9 10 4 5 5.1 1/4W D905 FR103 + ! 3 R914 0Ω 1/4W 8 2 D901 FR107 2 C914 0.1uF T901 3 SG901 ! C902 0.001uF/250V R901 680K 1/4W 1 1 R910 430K 1/4W C930 1500pF/1KV 3.5uH 2 R907 680K 1/4W D906 3 SG902 2 R909 430K 1/4W NC NC 4 ! 1 ! C905 100uF/450V L903 SP10150 2 D902 1 1 + ! 1 - 100K 2W L902 17.0mH C933 0.0022uF R905 1 3 C931 0.0022uF 2 + ! 2 4 R935 100 1/4W R934 100 1/4W R906 100 1/4W BD901 U4KB80R NC 2 1 CN901 SOCKET ! CN301 TPV (Top Victory) Electronics Co., Ltd. CN302 5 4 3 2 1 3 2 1 PHONEJACK INR GND INL CONN & WIRE 23 Title Size Date: POWER OUTPUT 12V & 5 V Document Number F OR SHARP L L 154 Rev ( PWPC521CP1P) F Sheet 1 of 2 15” LCD Color Monitor Sharp LL-153A 6.4 Audio Board 24 15” LCD Color Monitor Sharp LL-153A 7. PCB Layout 7.1 Main Board 25 15” LCD Color Monitor Sharp LL-153A 7.2 PWPC Board 26 15” LCD Color Monitor Sharp LL-153A 7.3 Audio Board 715G1144-3-SH 27 15” LCD Color Monitor Sharp LL-153A 7.4 Key Board 8. Maintainability 8.1 Equipments and Tools Requirement 1. Voltmeter.150 2. Oscilloscope. 3. Pattern Generator. 4. DDC Tool with an IBM Compatible Computer. 5. Alignment Tool. 6. LCD Color Analyzer. 7. Service Manual. 8. User Manual. 28 15” LCD Color Monitor Sharp LL-153A 8.2 Trouble Shooting 8.2.1 MAIN BOARD NO SCREEN APPEAR Measured CN701 pin5,6 = 12 V? Measured CN701 pin 9,10= 5V? Measured U702 pin 2= 3.3V? Measured U602 pin 2= 1.8V? Measured CN402 pin 1/2 = 5V? Measured CN402 pin 3/4 = 3.3V? NG Check Correspondent component. Is there any shortage or cold solder? Yes .there have OSD show Yes, all DC level exist Disconnected the Signal cable( Loose the Signal cable ),Is the screen show “Cable Not Connected” ? No, nothing is Led Orange Connected the Signal cable Led Green Connected the Signal cable again, Check LED status. Replace U402 Flash Rom Check Power switch is in Power-on status , and check if Power switch had been stuck ? Led orange again Led Green OK, Keyboard no Check the Wire-Harness from CN405 Measured RGB (R434, R435, R436 ) H,V Input at U401 pin 63,64 ,was there have signal ? Check Correspondent component short/open ( Protection Diode ) OK, Wire tight NG Check Panel-Power Circuit Block OK, input Normal OK ,Panel Power Check U401 Data-output Block NG,still no screen OK, U201 data Replace Power board and Check Inverter control relative circuit OK, clock Replace U401 (TSUM13AK) Re-do White balance adjust OK Note:1. If replace “MAIN-BOARD” , Please re-do “DDC-content” programmed & “WHITE-Balance”. 2. If replace “Power Board” only, Please re-do “ WHITE-Balance” 29 15” LCD Color Monitor Sharp LL-153A 2.PANEL POWER CIRCUIT Check R731 should have response from 0V to 5V NG , no transition Check the PPWR panel power relative circuit, Mea When we switch the power switch from on to off Q704(pin2) In normal operation, when LED =green, R731 should =0 v, OK Yes Measured the Q706 pin 3= 5 V? OK Replace Q602 ( N-MOS, A03401) NG, no Voltage OK 3. INVERTER CONTROL RELATIVE CIRCUIT Measured the inverter connector CN701 Check the Bklt-On relative circuit, R711, R712, NG In normal operation, when LED =green, R711,R712 Bklt-On should =5 v, Pin2 on/off control=5V (on) If Bklt-On no-response when the power switch Pin4 PWM signal control dim 0V-5V Replace power board to new-one and check turn on-off, Replace U401 TSUM13AK NG the screen is normal? Replace Power board & Re-do white balance OK 30 15” LCD Color Monitor Sharp LL-153A 4. U4-DATA OUTPUT Measured DCLK(pin 65,66 from U401) NG , no transition DVS, DHS (pin 63,64 from U401 ) Is the waveform ok? Replace TSUM13AK (U401) or DCLK around 48 MHZ , DVS=60.09Hz , DHS around 80 replace Main board. KHz ?(refer to input signal=640x480@60 Hz 31k, and LED is Green) OK Check TSUM13AK(U401) If Main Board being replace, please Signal output (PIN105-114, 118-127) do the DDC – content reprogrammed Is the waveform ok ? OK OK 8.2.2 Keypad Board OSD is unstable or not working N Connect Key Pad Board Is Key Pad Board connecting normally? Y N Is Button Switch normally? Replace Button Switch Y N Is Key Pad Board normally? Y Check main board 31 Replace Key Pad Board 15” LCD Color Monitor Sharp LL-153A 8.2.3 Power/Inverter Board 1.) No power Check CN902 pin5, 6 = 12V NG Check Interface board OK Check AC line volt 120V or 220V OK NG Change AC input Check the voltage of C905(+) OK NG Check bridge rectified circuit and F901 circut Check start voltage for the pin3 of IC901 OK NG Change R909,R910,R931 and Change IC901 Check the auxiliary voltage is bigger than 10V smaller than 20V NG 1) Check IC901 OK 2) Check ZD901, R915,C916…OVP circuit Check IC901 pin8 PWM wave NG Check IC901 OK Check Q903,R918, R919, R928,T901,ZD905,D901 32 15” LCD Color Monitor Sharp LL-153A 2.) W / LED , No Backlight Check C811(+) =12V NG Change L921 circuit OK Check ON/OFF signal NG Check Main board OK Check IC801 pin2=5V NG Change Q801,Q802,Q803 circuit OK Check the pin1,15 of IC801 have saw tooth wave NG Check IC801 pin6,7,10 OK Check the pin5 of IC801 NG Check D802,D804,Q806 circuit OK Check the resonant wave for PT801 OK NG Check Q805 circuit Check the output of PT801 NG OK Change PT801 Check connecter & lamp 33 15” LCD Color Monitor Sharp LL-153A 9. White-Balance, Luminance Adjustment Approximately 30 minutes should be allowed for warm up before proceeding White-Balance adjustment. 1. How to do the CA210 MEM. Channel setting A. Reference to CA210 user guide B. Use “ SC” key and “ NEXT” key to modify x, y, Y value and use “ID” key to modify the TEXT description Following is the procedure to do white-balance adjust: 2. Setting the color temp. you want A. MEM.CHANNEL 1 (9300K color): 9300K color temp. parameter is x = 383±20, y = 297±15, B. MEM.CHANNEL 2 (7500K color): 7500K color temp. parameter is x = 299±20, y = 315±15, C. MEM.CHANNEL 3 (6500K color): 6500K color temp. parameter is x = 313±20, y = 329±15, D. MEM.CHANNEL 3 (5000K color): 5000K color temp. parameter is x = 364±20, y = 359±15, E. MEM.CHANNEL 3 (4000K color): 4000K color temp. parameter is x = 282±20, y = 384±15, 3. Into factory mode of SHARP LL-154A Turn on power, press the MENU button, pull out the power cord, and then plug the power cord. Then the factory OSD will be at the left top of the panel. 4. Bias adjustment: Set the Contrast to 64; Adjust the Brightness to 31. 5. Gain adjustment: Move cursor to “-F-” and press MENU key A. Adjust 9300K color-temperature 1. Switch the CA210 to 9300 (with press “MODE” button) 2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210) 3. The LCD-indicator on CA210 will show x = 283±15, y = 297±15, 4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100 5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100 6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100 7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5 8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5 B. Adjust 7500K color-temperature 1. Switch the CA210 to 7500 (with press “MODE” button) 2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210) 3. The LCD-indicator on CA210 will show x = 299±15, y = 315±15, 4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100 34 15” LCD Color Monitor Sharp LL-153A 5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100 6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100 7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5 8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5 C. Adjust 6500K color-temperature 1. Switch the CA210 to STD (with press “MODE” button) 2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210) 3. The LCD-indicator on CA210 will show x = 313±15, y = 329±15, 4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100 5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100 6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100 7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5 8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5 D. Adjust 5000K color-temperature 1. Switch the CA210 to 5000 (with press “MODE” button) 2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210) 3. The LCD-indicator on CA210 will show x = 346±15, y = 359±15, 4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100 5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100 6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100 7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5 8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5 E. Adjust 4000K color-temperature 1. Switch the CA210 to 4000 (with press “MODE” button) 2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210) 3. The LCD-indicator on CA210 will show x = 282±15, y = 384±15, 4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100 5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100 6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100 7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5 8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5 C. Turn the Power-button off to quit from factory mode. 35 15” LCD Color Monitor Sharp LL-153A 10. Monitor Exploded View 36 15” LCD Color Monitor Sharp LL-153A 11. BOM List T56CM5NJXXXWAJ Location Part No. Description AUPC560KB8P AUPC BOARD FOR SMT CBPC6CM5XWJ1 MAIN BOARD KEPC6JA9 KEY BOARD PWPC521CP1P G2152-F-X-X-1-20061121 11G6055 1 口字框 11G6082 1 CLAMP 12G 394 3 FOOT 12G6051 1 Thermal Pal 15G5791 1 VESA BRACKET 34G1298 8M ST REAR COVER 34G1630A8M T FRONT COVER 34G1631 8M T STAND 34G1632 8M T BASE 37G 495 1 HINGE 44G3231 15 EVA WASHER 45G8088607SH3 EPE BAG FOR MONITOR 52G 1150 SH BLACK TAPE 52G 1210 AL Foil 52G6019 A 1 YELLOW TAPE 52G6022 22 GP Adhesive tape 52G6025 11582 MYLAR SHIELD 52G8001 8 NON-WOVEN FABRICS 78G 314 2 85G 707 1 K LCD Speaker MAIN SHIELD 89G 17356G556 AUDIO CABLE 89G 728GAB901 SIGNAL CABLE 89G401D18NISA POWER CORD 95G8014 12 36 HARNESS 12P-12P 80mm 95G8014 16 46 HARNESS 12P-16P 180MM 95G8018 24701 D WIRE HARNESS 20P-24P 115 XN01A M1G 330 4120 SCREW XN01B M1G 330 4120 SCREW XN01C M1G 330 4120 SCREW XN01A M1G 330 6120 SCREW XN01A M1G1140 5120 SCREW XN01A M1G1730 6120 M3*6 XN01B M1G1730 6120 M3*6 37 15” LCD Color Monitor Sharp LL-153A XN01C M1G1730 6120 M3*6 XN01A Q1G 330 6120 SCREW M3X6MM XN01A Q1G 330 10120 SCREW XN01A Q1G1030 SCREW 3X8 NI 8120 705GP503 1A SH PAPER PAD ASS'Y 750GLC50P1Q13N PANEL LCD CLAA150XP01Q 0 XN01A AM1G1740 10120 SCREW D-SUB J02G 247 SH SCREW J15G0030 MAIN FRAME 1 J44GP504624 1A CARTON J45G8088609SH1 EPE BAG FOR BASE J52G8025 11823 INSULATE SHEET AUPC560KB8SMTP AUPC BOARD FOR SMT 12G 408 10 THERMAL PAD CN204 33G3278 WAFER 3P PLUG 2.55mm CN202 33G802414C U201 56G 616 R212 61G 60222452T 220KOHM 5% 1/6W C205 67G215L471 3N 470UF/16V C207 67G215L471 3N 470UF/16V C208 67G215L471 3N 470UF/16V C201 67G215L681 4N 680UF 25V C202 67G215L681 4N 680UF 25V 90G6093 HEAT SINK 3 H WAFER 1 AMPLIFIER IC E-TDA7496L 1 AUPC560KB8AIP AUPC BOARD FOR AI R207 61G0603102 CHIPR 1KOHM +-5% 1/10W R208 61G0603102 CHIPR 1KOHM +-5% 1/10W R201 61G0603183 CHIP resistors 1/10W R203 61G0603183 CHIP resistors 1/10W R210 61G0603203 RST CHIP 20K 1/10W 5% R211 61G0603203 RST CHIP 20K 1/10W 5% R202 61G0603204 RST CHIP 200K 1/10W 5% C211 65G0805101 31 CHIP 100PF 50V NPD 0805 C212 65G0805101 31 CHIP 100PF 50V NPD 0805 C203 65G0805104 32 CHIP 0.1UF 50V X7R 0805 C213 65G0805104 32 CHIP 0.1UF 50V X7R 0805 C204 65G0805474 22 CHIP 0.47UF 25V Y5V 0805 C206 65G0805474 22 CHIP 0.47UF 25V Y5V 0805 C209 67G 2151097NT 1UF/50V C210 67G 2151097NT 1UF/50V 38 15” LCD Color Monitor Sharp LL-153A 715G1144 3 SH PCB SMTC6CM5XWJ1 MAIN BOARD CN404 33G801714H H PIN2*7 CN701 33G8027 12 WAFER 2*6P 2.0MM R/A CN403 33G8027 16 WAFER 16PIN 2.0MM DIP CN101 33G8027 24 H PIN 24P 2.0MM RIGHT ANGL 40G 45762412B CBPC LABEL C403 67G215V100 7N LOW ESR EC 10UF 50V NCC C408 67G215V100 7N LOW ESR EC 10UF 50V NCC C610 67G215V101 4N LOW ESR EC 100UF 25V NCC C707 67G215V101 4N LOW ESR EC 100UF 25V NCC C710 67G215V101 4N LOW ESR EC 100UF 25V NCC C609 67G215V221 4N LOW ESR EC 220UF 25V NCC C601 67G215V470 4N LOW ESR EC 47UF 25V NCC C602 67G215V470 4N LOW ESR EC 47UF 25V NCC C717 67G215V470 4N LOW ESR EC 47UF 25V NCC C719 67G215V470 4N LOW ESR EC 47UF 25V NCC L602 73G 253158 CHOKE COIL CN405 88G353A15F HJ D-SUB 15PIN 90G6250 Radiator L 1 GP X401 93G 22 53 CRYSTAL 14.31818MHZ HC-4 U601 56G 133 32 NS IC LM3485 MSOP-8 U401 56G 562102 TSUM13AK-LF PQFP-128 U602 56G 563 34 IC AIC1084-18PM TO-263 U405 56G 643 5A MAX810STRG SOT-23 IC U201 56G1133 34 IC M24C02-WMN6TP U303 56G1133 56 IC M24C16-WMN6TP U402 56G1133 81 Q404 57G 417 4 PMBS3904/PLILIPS Q405 57G 417 4 PMBS3904/PLILIPS Q701 57G 417 4 PMBS3904/PLILIPS Q703 57G 417 4 PMBS3904/PLILIPS Q401 57G 417 6 PMBS3906 PNP Q403 57G 417 6 PMBS3906 PNP Q602 57G 763 1 AO3401L Q704 57G 763 1 AO3401L F401 61G0603000 CHIPR 0OHM +-5% 1/10W F402 61G0603000 CHIPR 0OHM +-5% 1/10W FB409 61G0603000 CHIPR 0OHM +-5% 1/10W FB411 61G0603000 CHIPR 0OHM +-5% 1/10W X SST25LF020A-33-4C-SAE 39 15” LCD Color Monitor Sharp LL-153A FB412 61G0603000 CHIPR 0OHM +-5% 1/10W R419 61G0603000 CHIPR 0OHM +-5% 1/10W R421 61G0603000 CHIPR 0OHM +-5% 1/10W R480 61G0603000 CHIPR 0OHM +-5% 1/10W R493 61G0603000 CHIPR 0OHM +-5% 1/10W R494 61G0603000 CHIPR 0OHM +-5% 1/10W R702 61G0603000 CHIPR 0OHM +-5% 1/10W R409 61G0603101 CHIPR 100OHM +-5% 1/10W R414 61G0603101 CHIPR 100OHM +-5% 1/10W R427 61G0603101 CHIPR 100OHM +-5% 1/10W R428 61G0603101 CHIPR 100OHM +-5% 1/10W R429 61G0603101 CHIPR 100OHM +-5% 1/10W R441 61G0603101 CHIPR 100OHM +-5% 1/10W R442 61G0603101 CHIPR 100OHM +-5% 1/10W R443 61G0603101 CHIPR 100OHM +-5% 1/10W R445 61G0603101 CHIPR 100OHM +-5% 1/10W R453 61G0603101 CHIPR 100OHM +-5% 1/10W R454 61G0603101 CHIPR 100OHM +-5% 1/10W R455 61G0603101 CHIPR 100OHM +-5% 1/10W R481 61G0603101 CHIPR 100OHM +-5% 1/10W R486 61G0603101 CHIPR 100OHM +-5% 1/10W R411 61G0603102 CHIPR 1KOHM +-5% 1/10W R418 61G0603102 CHIPR 1KOHM +-5% 1/10W R420 61G0603102 CHIPR 1KOHM +-5% 1/10W R430 61G0603102 CHIPR 1KOHM +-5% 1/10W R433 61G0603102 CHIPR 1KOHM +-5% 1/10W R447 61G0603102 CHIPR 1KOHM +-5% 1/10W R456 61G0603102 CHIPR 1KOHM +-5% 1/10W R470 61G0603102 CHIPR 1KOHM +-5% 1/10W R483 61G0603102 CHIPR 1KOHM +-5% 1/10W R484 61G0603102 CHIPR 1KOHM +-5% 1/10W R701 61G0603102 CHIPR 1KOHM +-5% 1/10W R707 61G0603102 CHIPR 1KOHM +-5% 1/10W R731 61G0603102 CHIPR 1KOHM +-5% 1/10W R408 61G0603103 CHIPR 10KOHM+-5% 1/10W R413 61G0603103 CHIPR 10KOHM+-5% 1/10W R415 61G0603103 CHIPR 10KOHM+-5% 1/10W R416 61G0603103 CHIPR 10KOHM+-5% 1/10W R424 61G0603103 CHIPR 10KOHM+-5% 1/10W R425 61G0603103 CHIPR 10KOHM+-5% 1/10W 40 15” LCD Color Monitor Sharp LL-153A R426 61G0603103 CHIPR 10KOHM+-5% 1/10W R458 61G0603103 CHIPR 10KOHM+-5% 1/10W R474 61G0603103 CHIPR 10KOHM+-5% 1/10W R475 61G0603103 CHIPR 10KOHM+-5% 1/10W R476 61G0603103 CHIPR 10KOHM+-5% 1/10W R477 61G0603103 CHIPR 10KOHM+-5% 1/10W R479 61G0603103 CHIPR 10KOHM+-5% 1/10W R488 61G0603103 CHIPR 10KOHM+-5% 1/10W R490 61G0603103 CHIPR 10KOHM+-5% 1/10W R491 61G0603103 CHIPR 10KOHM+-5% 1/10W R492 61G0603103 CHIPR 10KOHM+-5% 1/10W R495 61G0603103 CHIPR 10KOHM+-5% 1/10W R496 61G0603103 CHIPR 10KOHM+-5% 1/10W R708 61G0603103 CHIPR 10KOHM+-5% 1/10W R711 61G0603103 CHIPR 10KOHM+-5% 1/10W R714 61G0603103 CHIPR 10KOHM+-5% 1/10W R478 61G0603104 CHIPR 100KOHM +-5% 1/10W R446 61G0603151 CHIPR 150 OHM +-5% 1/10W R608 61G0603200 2F RST CHIP 20K 1/10W 1% R605 61G0603220 CHIPR 22OHM+-5% 1/10W R448 61G0603222 CHIPR 2.2KOHM+-5% 1/10W R449 61G0603222 CHIPR 2.2KOHM+-5% 1/10W R728 61G0603222 CHIPR 2.2KOHM+-5% 1/10W R607 61G0603330 2F RST CHIP 33K 1/10W 1% R606 61G0603333 RST CHIP 33K 1/10W 5% R403 61G0603390 0F 390OHM +-1% R437 61G0603471 CHIPR 470OHM+-5%1/10W R405 61G0603472 CHIP 4.7KOHM +-5% 1/10W R422 61G0603472 CHIP 4.7KOHM +-5% 1/10W R450 61G0603472 CHIP 4.7KOHM +-5% 1/10W R451 61G0603472 CHIP 4.7KOHM +-5% 1/10W R705 61G0603472 CHIP 4.7KOHM +-5% 1/10W R712 61G0603472 CHIP 4.7KOHM +-5% 1/10W R717 61G0603472 CHIP 4.7KOHM +-5% 1/10W R723 61G0603513 CHIP 51K OHM R434 61G0603560 RST CHIP 56R 1/10W 5% R435 61G0603560 RST CHIP 56R 1/10W 5% R436 61G0603560 RST CHIP 56R 1/10W 5% R438 61G0603750 CHIPR 75OHM+-5%1/10W R439 61G0603750 CHIPR 75OHM+-5%1/10W 41 15” LCD Color Monitor Sharp LL-153A R440 61G0603750 CHIPR 75OHM+-5%1/10W ZD404 61G0805000 RST CHIP MAX F601 61G1206000 CHIP resistors 1/3W F602 61G1206000 CHIP resistors 1/3W R485 61G1206000 CHIP resistors 1/3W R732 61G1206102 CHIP 1K OHM 5% 1/8W C435 65G0603102 32 CHIP 1000PF 50 X7R C611 65G0603102 32 CHIP 1000PF 50 X7R C612 65G0603102 32 CHIP 1000PF 50 X7R C613 65G0603102 32 CHIP 1000PF 50 X7R C614 65G0603102 32 CHIP 1000PF 50 X7R C113 65G0603104 32 CHIP 0.1UF 50V X7R C401 65G0603104 32 CHIP 0.1UF 50V X7R C402 65G0603104 32 CHIP 0.1UF 50V X7R C404 65G0603104 32 CHIP 0.1UF 50V X7R C405 65G0603104 32 CHIP 0.1UF 50V X7R C406 65G0603104 32 CHIP 0.1UF 50V X7R C407 65G0603104 32 CHIP 0.1UF 50V X7R C409 65G0603104 32 CHIP 0.1UF 50V X7R C410 65G0603104 32 CHIP 0.1UF 50V X7R C411 65G0603104 32 CHIP 0.1UF 50V X7R C412 65G0603104 32 CHIP 0.1UF 50V X7R C413 65G0603104 32 CHIP 0.1UF 50V X7R C414 65G0603104 32 CHIP 0.1UF 50V X7R C415 65G0603104 32 CHIP 0.1UF 50V X7R C416 65G0603104 32 CHIP 0.1UF 50V X7R C419 65G0603104 32 CHIP 0.1UF 50V X7R C420 65G0603104 32 CHIP 0.1UF 50V X7R C426 65G0603104 32 CHIP 0.1UF 50V X7R C427 65G0603104 32 CHIP 0.1UF 50V X7R C428 65G0603104 32 CHIP 0.1UF 50V X7R C429 65G0603104 32 CHIP 0.1UF 50V X7R C430 65G0603104 32 CHIP 0.1UF 50V X7R C439 65G0603104 32 CHIP 0.1UF 50V X7R C440 65G0603104 32 CHIP 0.1UF 50V X7R C441 65G0603104 32 CHIP 0.1UF 50V X7R C445 65G0603104 32 CHIP 0.1UF 50V X7R C446 65G0603104 32 CHIP 0.1UF 50V X7R C447 65G0603104 32 CHIP 0.1UF 50V X7R C448 65G0603104 32 CHIP 0.1UF 50V X7R 42 0R05 1/8W 15” LCD Color Monitor Sharp LL-153A C603 65G0603104 32 CHIP 0.1UF 50V X7R C604 65G0603104 32 CHIP 0.1UF 50V X7R C701 65G0603104 32 CHIP 0.1UF 50V X7R C706 65G0603104 32 CHIP 0.1UF 50V X7R C709 65G0603104 32 CHIP 0.1UF 50V X7R C711 65G0603104 32 CHIP 0.1UF 50V X7R C720 65G0603104 32 CHIP 0.1UF 50V X7R C421 65G0603220 31 CHIP 22PF 50V NPO C423 65G0603220 31 CHIP 22PF 50V NPO C443 65G0603221 31 CAP:CER 220PF 5% 50V SMT C442 65G0603470 31 CHIP 47PF 50V NPO C432 65G0603473 32 CHIP 47NF 50V X7R C433 65G0603473 32 CHIP 47NF 50V X7R C434 65G0603473 32 CHIP 47NF 50V X7R C436 65G0603473 32 CHIP 47NF 50V X7R C437 65G0603473 32 CHIP 47NF 50V X7R C438 65G0603473 32 CHIP 47NF 50V X7R C417 65G0805105 22 CHIP 1UF 25V X7R 0805 C425 65G0805105 22 CHIP 1UF 25V X7R 0805 C444 65G0805105 22 CHIP 1UF 25V X7R 0805 C708 65G0805105 22 CHIP 1UF 25V X7R 0805 FB401 71G 56K121 M GP CHIP BEAD 120OHM T FB402 71G 56K121 M GP CHIP BEAD 120OHM T FB403 71G 56K121 M GP CHIP BEAD 120OHM T FB404 71G 56K121 M GP CHIP BEAD 120OHM T FB405 71G 56K121 M GP CHIP BEAD 120OHM T FB406 71G 56K121 M GP CHIP BEAD 120OHM T FB407 71G 56K121 M GP CHIP BEAD 120OHM T FB413 71G 56K121 M GP CHIP BEAD 120OHM T FB701 71G 56K121 M GP CHIP BEAD 120OHM T D407 93G 64 42 P D403 93G 6433P BAV99 SOT-23 D404 93G 6433P BAV99 SOT-23 D405 93G 6433P BAV99 SOT-23 ZD401 93G 39S 34 T ZENER DIODE UDZS5.6B ZD402 93G 39S 34 T ZENER DIODE UDZS5.6B ZD403 93G 39S 34 T ZENER DIODE UDZS5.6B ZD405 93G 39S 34 T ZENER DIODE UDZS5.6B ZD406 93G 39S 34 T ZENER DIODE UDZS5.6B ZD407 93G 39S 34 T ZENER DIODE UDZS5.6B BAV70 DIODE 43 15” LCD Color Monitor Sharp LL-153A ZD408 93G 39S 34 T ZENER DIODE UDZS5.6B ZD409 93G 39S 34 T ZENER DIODE UDZS5.6B ZD410 93G 39S 34 T ZENER DIODE UDZS5.6B ZD411 93G 39S 34 T ZENER DIODE UDZS5.6B ZD412 93G 39S 34 T ZENER DIODE UDZS5.6B ZD413 93G 39S 34 T ZENER DIODE UDZS5.6B ZD414 93G 39S 34 T ZENER DIODE UDZS5.6B D602 93G5004 2 715G1590 SSM54PT SMA DIODE 5A 40V 1 MAIN BOARD PCB SMTKEPC6JA9 KEYBOARD FOR SMT CN102 33G3802 2H WAFTER CN103 33G3802 2H WAFTER CN101 33G8027 12 H WAFER 2*6P 2.0mm R/A R103 61G 60210152T CFR 1/6W 100OHM +-5% R104 61G 60210152T CFR 1/6W 100OHM +-5% R101 61G 60251152T CFR 1/6W 510OHM +-5% R102 61G 60251152T CFR 1/6W 510OHM +-5% SW1 77G 600 1GCJ Switch SW2 77G 600 1GCJ Switch SW3 77G 600 1GCJ Switch SW4 77G 600 1GCJ Switch SW5 77G 600 1GCJ Switch D101 81G CN104 88G 30211K PHONE JOCK J1 95G 900 58 WIRE HARNESS ZD101 93G 39S 34 T ZENER DIODE UDZS5.6B ZD102 93G 39S 34 T ZENER DIODE UDZS5.6B ZD103 93G 39S 34 T ZENER DIODE UDZS5.6B ZD104 93G 39S 34 T ZENER DIODE UDZS5.6B ZD105 93G 39S 34 T ZENER DIODE UDZS5.6B 12 1F GP 715G1591 LED 2 KEPC PCB PW521CP1SMTP POWER BOARD FOR SMT W901 9G6005 PIN FOOT CN801 33G8020 2D AC CONN,2P R/A DIP BY ACES CN802 33G8020 2D AC CONN,2P R/A DIP BY ACES CN902 33G8027 12 WAFER 2*6P 2.0MM R/A 40G 45762412B CBPC LABEL 51G RTV Glue 1 6 45056863 IC902 56G 139 3A VAR901 61G 46 PC123Y22FZOF 9 10471 44 15” LCD Color Monitor Sharp LL-153A NR901 61G 58080 WT NTCR C903 63G 10747410S 0.47UF +-10% 250VAC C816 65G 3J2206ET 22PF 5% 3KV TDK C817 65G 3J5096ET 5PF 5% SL 3KV C901 65G306M1022BM Y1.CAP.001UF 250VAC MURA C902 65G306M1022BM Y1.CAP.001UF 250VAC MURA C921 65G306M1022BM Y1.CAP.001UF 250VAC MURA C909 67G215L102 4N LOW ESR 1000UF 25V C912 67G215L102 4N LOW ESR 1000UF 25V C811 67G215L471 4Q LOW ESR EC 470UF 25V UH C906 67G215L471 4Q LOW ESR EC 470UF 25V UH C911 67G215L471 4Q LOW ESR EC 470UF 25V UH C905 67G215S10115Q LOWESR EC 100UF 450V PAG FB901 71G Φ3.5*Φ0.8*2.2\ 100MM> L903 73G 253 91 LS CHOKE COIL L904 73G 253 91 LS CHOKE COIL L901 73L 174 53 LG GP LINE FILTER L902 73L 174 55 LG GP LINE FILTER PT801 80GL15T 30 DN T901 80LL19T CN301 88G 30214K PHONE JACK 5PIN BD901 93G 50460900 GBU408 D901 93G 6026T52T FR107-DO-41 1000V/1A D905 93G 6038T52T FR103 DO-41 200V/1A CN302 95G8013 55 29 7 LG 3704 X'FMR 74uH TK.2026.101 GP TRANSFORMER X HARNESS 705G 560 57S44 R905 ASS'Y 705G 780 57S7P Q903 ASS'Y 705GJ5K0 61001 R904 ASS'Y 705GJ5K0 87001 CN901 ASS'Y 705GJ5K0 93001 D902 ASS'Y 705GJ5K0 93002 D904 ASS'Y 705GJ5K0 95001 JP907 ASS'Y PW521CP1AIP POWER FOR AI IC901 56G 379 76 IC LD7552BPS SOP-8 IC801 56G 608 10 OZ9938GN SOIC-16 Q801 57G 417 4 PMBS3904/PLILIPS Q802 57G 417 4 PMBS3904/PLILIPS Q803 57G 417 4 PMBS3904/PLILIPS Q902 57G 417 4 PMBS3904/PLILIPS Q901 57G 417 6 PMBS3906 PNP 45 15” LCD Color Monitor Sharp LL-153A Q804 57G 759 2 TRANSISTOR RK7002 SOT-3 Q806 57G 759 2 TRANSISTOR RK7002 SOT-3 Q807 57G 759 2 TRANSISTOR RK7002 SOT-3 Q808 57G 759 2 TRANSISTOR RK7002 SOT-3 Q805 57G 763 14 AM9945N-T1-PF R839 61G0805000 RST CHIP MAX 0R05 1/8W R844 61G0805000 RST CHIP MAX 0R05 1/8W R925 61G0805000 RST CHIP MAX 0R05 1/8W RJ824 61G0805000 RST CHIP MAX 0R05 1/8W R836 61G0805100 RST CHIP 10R 1/8W 5% R837 61G0805100 RST CHIP 10R 1/8W 5% R826 61G0805100 2F RST CHIP 10K 1/8W 1% R915 61G0805101 RST CHIP 100R 1/8W 5% R923 61G0805102 CHIPR 1K OHM +-5% 1/10W R924 61G0805102 CHIPR 1K OHM +-5% 1/10W R926 61G0805102 CHIPR 1K OHM +-5% 1/10W R803 61G0805103 CHIP 10KOHM 1/10W R804 61G0805103 CHIP 10KOHM 1/10W R812 61G0805103 CHIP 10KOHM 1/10W R820 61G0805103 CHIP 10KOHM 1/10W R919 61G0805103 CHIP 10KOHM 1/10W R810 61G0805104 RST CHIP 100K 1/8W 5% R815 61G0805104 RST CHIP 100K 1/8W 5% R821 61G0805104 RST CHIP 100K 1/8W 5% R813 61G0805105 RST CHIP 1M 1/8W 5% R816 61G0805105 RST CHIP 1M 1/8W 5% R845 61G0805105 RST CHIP 1M 1/8W 5% R847 61G0805105 RST CHIP 1M 1/8W 5% R848 61G0805105 RST CHIP 1M 1/8W 5% R809 61G0805204 RST CHIPR 200 KOHM +-5% R807 61G0805220 RST CHIP 22R 1/8W 5% R840 61G0805242 RST CHIP 2K4 1/8W 5% R841 61G0805242 RST CHIP 2K4 1/8W 5% R922 61G0805243 1F RST CHIPR 2.43 KOHM +-1% R825 61G0805271 CHIPR 270 OHM +-50% 1/8W R912 61G0805272 RST CHIP 2K7 1/8W 5% R802 61G0805304 RST CHIPR 300 KOHM +-5% R920 61G0805330 2F CHIP 33KOHM 1/10W/1% R838 61G0805360 0F RST CHIPR 360 OHM +-1% 1 R921 61G0805360 1F CHIP 3.6KOHM 1/10W 1% 46 SOIC-8 15” LCD Color Monitor Sharp LL-153A R817 61G0805360 2F RST CHIPR 36 KOHM +-1% 1 R843 61G0805471 RST CHIP 470R 1/8W 5% R913 61G0805472 RST CHIP 4K7 1/8W 5% R811 61G0805473 RST CHIP 47K 1/8W 5% R827 61G0805510 1F RST CHIPR 5.1 KOHM +-1% R814 61G0805563 RST CHIP 56K 1/8W 5% D906 61G1206000 CHIP resistors 1/3W JR902 61G1206000 CHIP resistors 1/3W R801 61G1206000 CHIP resistors 1/3W R918 61G1206100 RST CHIP 10R 1/4W 5% R930 61G1206100 3F RST CHIPR 100 KOHM +-1% R906 61G1206101 CHIP 100OHM 5% 1/8W R916 61G1206101 CHIP 100OHM 5% 1/8W R927 61G1206101 CHIP 100OHM 5% 1/8W R934 61G1206101 CHIP 100OHM 5% 1/8W R935 61G1206101 CHIP 100OHM 5% 1/8W R936 61G1206101 CHIP 100OHM 5% 1/8W R937 61G1206101 CHIP 100OHM 5% 1/8W R806 61G1206105 CHIP 1MOHM 5% 1/8W R818 61G1206150 RST CHIP 15R 1/4W 5% R819 61G1206150 RST CHIP 15R 1/4W 5% R808 61G1206204 RST CHIPR 200 KOHM +-5% R909 61G1206434 RST CHIPR 430 KOHM +-5% R910 61G1206434 RST CHIPR 430 KOHM +-5% R931 61G1206434 RST CHIPR 430 KOHM +-5% R805 61G1206471 RST CHIP 47OR 1/4W 5% R911 61G1206472 CHIP 4.7KOHM 5% 18W R914 61G1206519 CHIP resistors 1/3W R901 61G1206684 CHIPR 680KOHM +-5% 1/8W R902 61G1206684 CHIPR 680KOHM +-5% 1/8W R903 61G1206684 CHIPR 680KOHM +-5% 1/8W R907 61G1206684 CHIPR 680KOHM +-5% 1/8W R908 61G1206684 CHIPR 680KOHM +-5% 1/8W R932 61G1206684 CHIPR 680KOHM +-5% 1/8W C805 65G0805102 32 CHIP 1000PF 50V X7R 0805 C917 65G0805102 32 CHIP 1000PF 50V X7R 0805 C807 65G0805103 32 CHIP 10000 PF 50V X7R 08 C803 65G0805104 22 CHIP 0.1UF 25VX7R 0805 C907 65G0805104 22 CHIP 0.1UF 25VX7R 0805 C910 65G0805104 22 CHIP 0.1UF 25VX7R 0805 47 15” LCD Color Monitor Sharp LL-153A C915 65G0805104 22 CHIP 0.1UF 25VX7R 0805 C916 65G0805104 22 CHIP 0.1UF 25VX7R 0805 C801 65G0805104 32 CHIP 0.1UF 50V X7R 0805 C820 65G0805104 32 CHIP 0.1UF 50V X7R 0805 C821 65G0805104 32 CHIP 0.1UF 50V X7R 0805 C822 65G0805104 32 CHIP 0.1UF 50V X7R 0805 C806 65G0805105 22 CHIP 1UF 25V X7R 0805 C918 65G0805105 22 CHIP 1UF 25V X7R 0805 C804 65G0805155 A2 1.5 UF 10V C802 65G0805221 31 CHIP 220PF 50V NPO C818 65G0805271 31 CHIP 270pF 50V NPO 0805 C919 65G0805471 21 CHIP 470PF 25V NPO 0805 C812 65G0805472 31 CHIP 4700PF 50V X7R 080 C813 65G0805472 31 CHIP 4700PF 50V X7R 080 C823 65G0805472 31 CHIP 4700PF 50V X7R 080 C824 65G0805472 31 CHIP 4700PF 50V X7R 080 C809 65G0805473 32 SMD 47NF +-10% 50V C819 65G0805473 32 SMD 47NF +-10% 50V C810 65G080556131G MLCC 0805 560PF G 50V NP C808 65G0805682 32 CHIP 6.8nF 50V X7R 0805 C932 65G1206102 72 CHIP 1000PF 500V X7R C914 65G1206104 32 CHIP 0.1UF 25V X7R 1206 C931 65G1206222 72 CHIP 2200PF 500V X7R C933 65G1206222 72 CHIP 2200PF 500V X7R D802 93G 64 33 BAV99 SOT-23 D801 93G 64 42 PP DIODE BAV70 SOT-23 D803 93G 64 44 S CHIP DIODE LL4148WP D804 93G 64 44 S CHIP DIODE LL4148WP D903 93G 64 44 S CHIP DIODE LL4148WP ZD904 93G 39S 17 T RLZ12B LLDS ZD903 93G 39S 19 T PTZ7.5B ZD901 93G 39S 23 T GLZ22B ZD801 93G 39S 24 T RLZ5.6B ROHM ZD902 93G 39S 25 T RLZ5.1B ROHM ZD905 93G 39S 44 T RLZ18B LLDS CN901 6G 31500 2.0MM EYELET C905 6G 31502 1.5MM RIVET L901 6G 31502 1.5MM RIVET L902 6G 31502 1.5MM RIVET PT801 6G 31502 1.5MM RIVET 48 15” LCD Color Monitor Sharp LL-153A Q903 6G 31502 1.5MM RIVET R904 6G 31502 1.5MM RIVET T901 6G 31502 1.5MM RIVET IC903 56G 158 10 R928 61G 20022152T 220OHM 1% 1/4W R822 61G212Y305 KT MGFR 3M OHM +-5% 1/2W C930 65G 1500PF +/-10% 1KV Y5P C922 67G 2152207NT 22UF/50V F901 84G 55 7W 250V/3.15A FUSE F902 84G 55 7W 250V/3.15A FUSE Q903 IC AZ431AZ-AE1 TO-92 1K152 1T 715G2152 R905 T F PCB 61G152M10458G 100K OHM 5% 2W 96G SHRINK TUBE UL/CSA 29 6 51G 200 1 6342 Coolant Oil 57G 667 30 2SK2645-54MR TO-220F 90G6084 HEAT SINK 1 XN01A AM1G1730 R904 61G 2J68858G 0.68 OHM 5% 2W 96G 29 SHRINK TUBE UL/CSA CN901 8120 SCREW 6 87G 501 36 S AC SOCKET 95G 900703 X WIRE HARNESS 96G 29 6 51G 200 1 90G6084 1 D902 93G XN01A AM1G1730 SHRINK TUBE UL/CSA 6342 Coolant Oil HEAT SINK 60245 51G 200 DIODE SP10150 ITO-220 8120 1 SCREW 6342 Coolant Oil 90G6084800 HEAT SINK D904 93G DIODE SP10150 ITO-220 XN01A AM1G1730 96G 60245 29 8120 SCREW 1 H.S.TUBE 44GP503 1A 1 PAPER PAD-1 44GP503 1A 2 PAPER PAD-2 44GP503 1A 3 PAPER PAD-3 49