Download Casablanca Hampshire Owner`s manual
Transcript
HAMPSHIRE™ Hampshire™ Owner’s Manual READ AND SAVE THESE INSTRUCTIONS! Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s manual completely and carefully. Retain this manual for future reference. CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure. CONTENTS INTRODUCTION Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safe Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 MOUNTING RECOMMENDATIONS General Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Sloped Ceiling Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FAN INSTALLATION Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Crossbar Mounting Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Lag Screw Installation (Optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Canopy Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Blade Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Fan Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Hanging the Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Canopy Electrical Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Canopy Hatch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Switch Housing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Light Fixture Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 VERSA•TOUCH2™ CONTROL INSTALLATION Control Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Changing Transmitter Frequency Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Remote Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 TROUBLESHOOTING TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 CARE RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 AUTHORIZED SERVICE CENTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 PRODUCT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 C7K62M AT1206 1 INTRODUCTION BEFORE YOU START • CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-1999, and local codes. All wiring must be performed in accordance with national and local electrical codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician. To avoid overheating and possible damage to other equipment, do not install control to a receptacle, fluorescent light fixture, motor operated appliance, or transformer-supplied appliance. • This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling installations. • This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum current requirement for the fan with light fixture is 2.3 amps. The fan uses about 1 amp or 100 watts. Maximum light current is about 1.25 amps or 150 watts of lighting. • Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make sure all wires are within the canopy and that no wires are being pinched. • WARNING: Do not bend the blade brackets when installing the brackets, balancing the blades or cleaning the fan. Do not insert foreign objects in between the rotating fan blades. • WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state speed control device. Use only the control provided with or recommended for this fan. Unpacking Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed in the parts guide. Before discarding packaging material, be certain that all parts have been removed. For best performance and for your warranty to be valid, use only genuine Casablanca blades, light fixtures, and accessories. SAFE USE • The blades in each pack are matched for equal weight to assure smooth fan operation. If more than one fan is being installed, be careful not to mix blades from different cartons. Circuit Breaker (Trip breaker for the circuit you will be working on) Fuse Box (Remove fuse for the circuit you will be working on) • Inspect the contents of your carton for possible shipping or handling damage. If parts are missing or damaged, call 1-888-227-2178. • It is always a good idea to have an assistant to help with the installation. • When cleaning, painting, or working near your fan, be very careful of the fan and blades. Always turn the power OFF to the ceiling fan before working on it or replacing lightbulbs. • Never insert anything into the path of the fan blades while the fan is in operation. • Never install a fan over a pool or spa. • Never operate a fan that has been damaged in any way. Contact Casablanca Fan Company by calling 1-888-227-2178, or contact your local authorized Casablanca dealer for assistance in obtaining service. 2 18" ↑ 70"↑ 84" ↑ HAMPSHIRE™ MOUNTING RECOMMENDATIONS GENERAL GUIDELINES Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7' above the floor. • Do not locate the fan in a doorway or above a swinging door. • In bedrooms, fans work best when mounted above the foot of the bed. • Over pool tables, be sure to provide plenty of clearance to avoid damage from pool cues. • In kitchens be sure to allow for open cupboard doors to clear the fan blades. • Do not install a fan close to or over a pool or spa. High humidity combined with corrosive gases will destroy the finish and warp the blades. Fan Size Variable fan speed capability permits the use of a full-size 52" fan even in smaller rooms. For very large rooms, two fans may be needed. SLOPED CEILING INSTALLATIONS SUGGESTED EXTENSION POLE LENGTHS Ceiling Height 8' 0" 8' 6" 9' 0" 9' 6" 10' 0" 11' 0" 12' 0" 13' 0" 14' 0" Pole Length Extension Pole standard standard 6" 12" 12" 18" 24" 36" 48" Maximum Hang-Tru® angle 32º Blades must be a minimum of 7 feet above the floor 7' minimum When to Use Extension Poles For optimum performance and appearance, an extension pole should be used with your Casablanca fan when installing on high (cathedral) ceilings or sloped ceilings. Casablanca offers standard poles in increments of 6" up to 5'. Custom poles are available in lengths up to 9'9". See your Authorized Casablanca Dealer for details. NOTE: Fan may wobble or vibrate if pole length is not long enough and inside blade is too close to downslope or side wall. Extending pole length will usually solve problem. EXAMPLE 1 EXAMPLE 2 Calculation of Ceiling Angle Use the tear-off Ceiling Angle Template card inserted in this manual. It provides you with a simple “go” or “no-go” for installing your fan on a sloped ceiling. EXAMPLE 3 This slope is less than 32º. It is OK to install your fan. This slope is 32º. This is the maximum slope that will allow the fan to hang straight down. It is OK to install your fan. This slope is more than 32º. Your fan will not hang straight down, an adaptor is necessary. Contact your local Authorized Casablanca Dealer in regards to purchasing a “Sloped Ceiling Adaptor.” 3 FAN INSTALLATION GETTING STARTED Installing a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired. After turning the power OFF at its source (either the circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure it is marked “Approved for Ceiling Fan Mounting.” If it is not, a new box must be installed. WARNING! To reduce the risk of fire, electrical shock, or personal injury, mount to outlet box marked “Acceptable Fan Support of 22.7 kg (50 lbs.) or less” using the mounting hardware provided with the outlet box. Note: The weight of this fan is 34 pounds. CROSSBAR MOUNTING BRACKET INSTALLATION CEILING HARDWARE (not to scale) Crossbar Mounting Bracket Screw Pack A: Lag Screw and Washer (1) 1" x 8-32 Roundhead Screw and Washer (2) Note: After removing the old fixture, check the outlet box to insure that it is supported by a joist or beam across its upper surface. If not, a 2 x4 stud must be installed. Step 1a. Remove the knockout plug in the center of the outlet box or drill a 1/2-inch hole for the lag screw to pass through. Then drill a 1/4-inch guide hole into the joist or beam to a depth of 3 inches. Step 1b. Route the outlet box wires through the keyhole slot of the crossbar mounting bracket as shown. Attach the crossbar mounting bracket to the outlet box with the provided screws from Pack A, making sure the outlet box wires are not pinched by the washer. Joist Ceiling-Fan-Approved Wiring Box Crossbar Mounting Bracket Green Ground Wire CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket. WARNING! 4 Wire Nut (4) 1" x 8-32 Roundhead Screw Ceiling Wiring Ridge side down Washer HAMPSHIRE™ LAG SCREW INSTALLATION (OPTIONAL) NOTE: This step is required only under two conditions: If the fan weighs 36 lbs. or more (which does not pertain to this fan) or if the existing ceiling fixture outlet box needs to be modified for a ceiling fan application (for example, if the house is not new construction and you are replacing an existing light fixture). We recommend that the ceiling box be of sufficient capacity to support the weight of the fan and light fixture under any conditions. If in doubt whether you need to install the lag screw, consult a qualified electrician. Step 2 (optional). With the large washer attached, pass the lag screw (Pack A) through the center hole of the crossbar mounting bracket and screw into the guide hole. Tighten until the outlet box is mounted firmly to the beam. This box must be secured to the ceiling firmly. CANOPY INSTALLATION CANOPY HARDWARE (not to scale) Screw Pack B: Canopy Screws and Washers (5) Canopy Hatch Canopy Step 3. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/2" long canopy screws (Screw Pack B) and lock washers provided with your Casablanca fan. Tighten using the provided screwdriver until snug against the ceiling. NOTE: On sloped ceilings, align the canopy opening with the top or peak of the room. Feed outlet box wires through canopy opening Canopy Lock Washer Canopy Screw 5 BLADE INSTALLATION BLADE HARDWARE (not to scale) Blades (4) Blade Irons (4) Attach Blade Irons Step 4a. Using Screw Pack C and the provided screwdriver, attach the blades to the blade holders by aligning the screwholes of the blade iron with the holes in the blade. Attach the blade iron using the four blade screws and washers provided for each blade as shown. Tighten securely by hand only. Blade Installation: Step 5. Using Screw Pack D and the provided screwdriver, attach the blade assembly to the motor as shown. Tighten screws by hand only. TIP: For balancing purposes, loosely install all four blades to the motor before tightening the blade screws securely. CAUTION: Blade screws must be tightened securely before operating the fan. 6 Screw Pack C: Blade Screws and Washers (17) Screw Pack D: Blade Iron Screws (9) HAMPSHIRE™ FAN PREPARATION PERMA•LOCK™ HARDWARE (not to scale) Uplight Lightbulbs S-11 25-watts (4) IMPORTANT SAFETY INFORMATION: Before starting the installation of your ceiling fan, install the threaded downrod into the motor coupling and lock the assembly. 3" Perma•Lock™ Downrod and Ball Assembly Allen Wrench Ground Wire (green) Motor Wires (leave at least 6" long) Perma•Lock™ Downrod and Ball Assembly Prepare for fan installation as follows: Allen Wrench Tapered Thread Step 6a. Remove the paper shield from the motor. Step 6b. Using the provided Allen wrench (attached to the paper motor warning shield), loosen the Allen set screw. Motor Coupling Allen Set Screw Step 6c. Route the wires through the Perma•Lock™ downrod and ball assembly. Insert the downrod into the motor coupling and turn it clockwise until it stops turning, ensuring that the pole has bottomed out. TIP: The downrod has a tapered thread that is designed to lock completely when installed correctly. Motor Housing Assembly Caution Shield HI A NG RS N IR I BE SET TIGHTLY AGAINST THE DOWNROD THREADS AFTER FAN IS ASSEMBLED FAILURE TO DO SO WILL CAUSE FAN TO FALL W CONFIRM LOCKSCREW IS PROPERLY TIGHTENED P/N 1942640 SRB4/96 TIGHTEN LOCKSCREW PLETE DO NOT OIL SEALED BEARINGS! INSTALLER INSTALLER GIVE THIS TAG TO THE CONSUMER AFTER INSTALLATION COMPLETE CO M MO TO A CE UN TIL IN S TA L IN PL LAT IO D E VE LEA DANGER LD IT IS IMPERITIVE THAT THE LOCKSCREW N Step 6d. Tighten the set screw with the Allen wrench to ensure safe operation of your fan. If it is tight enough, you should not be able to turn the downrod counterclockwise with your hands. If in doubt, tighten the set screw with the Allen wrench until you cannot turn it any further. TIGHTEN LOCKSCREW CAUTION DAMP LOCATION RATED FANS M LE TE RE REQUIRE A GROUND FAULT INTERRUPTER (GFI) USE A WEATHER PROOF OUTLET BOX PROPERLY CONNECT GROUND WIRES O VE P USE ONLY UNDER A WEATHER M TH PROOF STRUCTURE CO I SS H IE LD W H EN I N S TA LLA N TI O IS CAUTION: Failure to fully lock in the downrod before securely tightening the Allen set screw may cause the fan to separate from the downrod and fall during normal operation. Install Incandescent Lightbulbs Step 7. Screw in four 25-watt incandescent lightbulbs as shown. NOTE: When replacing lightbulbs, be sure to use only 25-watt maximum. 7 HANGING THE FAN Step 8a. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires are pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. Ball Step 8b. Trim excess motor wires, leaving at least 6 inches above the downrod. Strip 1/2-inch insulation from the end of each wire using a wire stripper (available at your local hardware store). The splices after being made should be turned upward and pushed carefully into the outlet box. Slot CANOPY ELECTRICAL CONNECTIONS Step 9. Attach the fan wires to the ceiling fixture outlet box wiring by placing the bare ends of the wires side by side and then securing with a wire nut. Test that the connection is secure by pulling on the wire nut. Connect in this order: Wire Nut • GREEN leads from mounting plate and downrod assembly of fan to GROUND conductor of power source. Secure with wire nut. • WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box. Secure with wire nut. • BLACK power wire from fan to BLACK power wire in ceiling outlet box. Secure with wire nut After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box. 2 Black Wires 2 White Wires 3 Green Wires NOTE: If the color of your ceiling wires differs from that described, consult an electrician. CANOPY HATCH INSTALLATION Step 10a. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Step 10b. Install the canopy hatch with the last canopy screw and lock washer using the provided screwdriver. To do this, tilt the fan body away from the hatch opening. Tighten the screws firmly. Step 10c. Straighten the fan, then check to ensure that there is no movement between the canopy and the ceiling or the Perma•Lock™ downrod and the ball assembly. 8 Pin HAMPSHIRE™ SWITCH HOUSING INSTALLATION SWITCH HOUSING HARDWARE (not to scale) Switch Housing Mounting Plate Screw Pack E: Motor and Switch Housing Mounting Plate Screws (6) Glass Shade 60-watt b-10 bulb (Candelabra-base) Light Assembly Step 11a. Using the screws from Screw Pack E and the provided screwdriver, install two screws into the motor bottom housing as shown. Step 11b. Route the light connector wires through the switch housing mounting plate as shown. Step 11c. Align the switch housing mounting plate with the two screws in the motor bottom housing and turn counterclockwise to align the keyhole slots in the plate with the two screws as shown. Step 11d. Install the third screw and securely tighten all three screws by hand only. LIGHT FIXTURE INSTALLATION Step 12a. Using the screws from Screw Pack E and the provided screwdriver, install each of the three screws into the switch housing mounting plate as shown. Step 12b. Connect the light assembly connector to the motor connector as shown. Carefully tuck wires into the switch housing mounting plate. Step 12c. Align the keyhole slots in the light assembly with the three screws in the switch housing mounting plate and turn counterclockwise to align the keyhole slots with the three screws as shown. Step 12d. Securely tighten all three screws by hand only. Lightbulb Installation Step 13. Screw in two 60-watt type B-10 Candelabra-base lightbulbs. NOTE: When replacing lightbulbs, be sure to use only 60-watt maximum. Glass Installation Step 14a. Remove finial from Light Assembly. Step 14b. Insert the threaded rod from the Light Assembly through the hole in the glass shade, as shown. Step 14c. Thread finial onto threaded rod. Tighten securely. 9 VERSA•TOUCH2™ CONTROL INSTALLATION VERSA•TOUCH2™ HARDWARE (not to scale) 12v Battery W-73 Control Wood Screw 1" (2) Drywall Anchor 6-32 (2) Screw 6-32 X 3/8" (2) Screw 6-32 X 1" (2) W-73 Control Holder CONTROL BRACKET INSTALLATION SAFETY FIRST: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch. CAUTION! Do not use with wall dimmer. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state speed control device. Use only the control provided with this fan. Step 15. Follow instructions for the type of transmitter control bracket you will be using. Standard Toggle Switch Inner mounting holes Rocker Light Switch Outer mounting holes Switch Cover Plate Switch Cover Plate Control Bracket Control Bracket Standard Light Switch Rocker Light Switch Step A. Remove the two screws holding the switch cover plate. Do not remove the cover plate. Step A. Break off the two tabs by pushing outward. Step B. Orient the control bracket as shown and line up the two inner mounting holes with those on the switch. Step C. Insert and tighten the screws using the provided screwdriver. Wall Installation Step A. L ocate a 2x4 wall stud in a convenient location. Step B. Remove the two screws holding the switch cover plate. Do not remove the cover plate. Step C. Orient the control bracket as shown and line up the two inner mounting holes with those on the switch. Step D. Insert and tighten the screws using the provided screwdriver. NOTE: The wall anchors and 6-32 x 1" screws may be used in situations where mounting to a stud is not possible. Use the inner mounting holes. After securing the anchor, discard the anchor’s pointed screws and use the 6-32 decor ovalhead screws supplied. Step B. Orient the control bracket as shown over the 2x4 stud. Step C. Insert the 1" wood screws in either the inner or outer mounting holes and tighten using the provided screwdriver. Anchor Panhead Screw Wood Screw 1" 10 Drywall Anchor Decor Ovalhead Screw 6-32 X 1" HAMPSHIRE™ REMOTE OPERATION Fan Control To start the fan. Press the selected speed button to run the fan at the desired speed. Send Signal LED LOW=Low speed MED=Medium speed HIGH=High speed UPTo turn off the fan, press the FAN OFF button. Airflow Direction MED To reverse the airflow, press the REVERSE button. REVERSE operates at any speed whether the fan is on or off. The fan returns to its set speed after reversing. LOW Light Control Turn the light on or off independently from the fan by pressing the LIGHT rocker switch. (Press the left side for the uplight, right side for the downlight, and the middle for both.) If you press the button for more than 0.7 seconds, it becomes a dimmer. The light varies from “bright" to “dim” over approximately 8 seconds. If you continue to hold the LIGHT button, this sequence will reverse when the light reaches its brightest or dimmest level. REVERSE Release the button when the desired level is reached. Auto Resume Quick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains the desired brightness level set previously. DOWNLIGHT HIGH FAN OFF CHANGING TRANSMITTER FREQUENCY SETTING Note: All fans leave the factory set to “00000.” Versa•Touch 2 Control (back) You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. Step 1. At the circuit breaker or fuse box, turn the power off for the fan you want to change. Step 2. Open the battery door of the Versa•Touch control and remove the batteries. Step 3. Change the dip switch settings, assuring that they are different from the previously installed Versa•Touch fan. Step 4. Reinstall the batteries and the battery door on the control. Dip Switch set to “10000” Dip Switch set to “01001” Step 5. At the circuit breaker or fuse box, turn the power back on for the fan whose frequency you are changing. WARNING! Note: You may want to label your controls to assure you do not mix them up. Do not turn the power off at the circuit breaker, then back on, for the previously installed Versa•Touch2 fan(s), as you may inadvertently change the frequency settings for it as well. 2 If the fan is not functioning after installation: Step 1. Check to make sure the batteries are installed correctly in the control. 3 Step 2. Turn the power off to the fan (from the circuit breaker) for at least 5 seconds. Step 3. Turn the power back on (at the circuit breaker) and push the HIGH, MED, and LOW buttons–in that order–within 20 seconds. The fan should now function properly. Circuit Breaker or Fuse Box 1 Press in this order to set new frequency: 1. HIGH 2. MED 3. LOW 11 TROUBLESHOOTING TIPS Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. PROBLEM POSSIBLE REMEDIES Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make sure the power is turned off during this inspection. • The battery is weak. Install a fresh battery. • The fan receiver is defective. Replace the fan receiver. • Check the frequency setting: Turn the power off at the circuit breaker, for the fan that is not functioning only. Check that the jumper switches match in both the receiver and the transmitter. Fan wobbles or shakes excessively • Be sure the canopy pin is set properly into the slot on the ball. • Check that the bladeholders have not been bent during installation and the blades are balanced. • The hanger bracket and/or the ceiling outlet are attached too loosely. Make sure the hanger bracket is attached tightly to the ceiling outlet box and the downrod assembly is secured firmly. • The downrod is attached to the downrod base too loosely. Make sure all the screws are securely tightened. Fan is noisy during operation • Check and tighten the light fixture retaining screws, glass shade screws, and/or lightbulb(s). • Tighten the canopy screws and mounting plate assembly. Make sure the wire nuts inside the canopy and switch housing are not touching the metal parts and that they have not fallen off the wire splices. Tighten as necessary. • Tighten the blade holders to the flywheel (or direct drive motor) and the blades to the bladeholder screws. • Make sure all the screws in the motor housing are snug but not overly tight. Fan does not run on low speed • If fan is new, it may need to be “broken in.” Run at high speed for several days. Battery life is short • Replace with alkaline batteries. Light works, but fan does not work • The fan wires are not connected properly. Follow the instructions in Step 8. Fan and light run only on full speed • The fan receiver is defective. Replace the fan receiver. Fan is missing one speed • The fan receiver is defective. Replace the fan receiver. Fan does not change speed, but light works • The fan receiver is defective. Replace the fan receiver. Reverse does not work • The fan receiver is defective. Replace the fan receiver. Fan starts working by itself • There is frequency interference. Change frequency as described on Page 11. Fan operates only when transmitter is close • Check that antenna wire is not touching the metal plate. Fan works, but light does not dim • The fan receiver is defective. Replace the fan receiver. Fan works, but light does not work • The fan receiver is defective. Replace the fan receiver. • The light socket is broken. Replace the socket. • A lightbulb is defective. Replace the lightbulb. 12 HAMPSHIRE™ CARE RECOMMENDATIONS Fan Finishes • For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. • A vacuum cleaner brush nozzle can remove heavier dust. • Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish. Blades • Wood-finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be applied for added protection and beauty. • For painted and high-gloss blades, surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish. No Need for Lubrication • Never lubricate this fan! The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated for life. • Do not attempt to oil the motor. Changing Lightbulbs • Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs. • Replace bulbs with the same type as you removed from the light fixture. • The maximum wattage rating for this fan’s light kit is 100 watts for the uplight, 120 watts for the downlight. For questions or to locate the nearest Casablanca Authorized Service Center call toll free: 1-888-227-2178 or visit us on the web at: www.casablancafanco.com This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. NOTE: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one's authority to operate this remote control. 13 AUTHORIZED SERVICE CENTERS STATE/CITY ZIP SERVICE CENTER NAME PHONE ALASKA Anchorage 99518 Bering Sea Eccotech 907-563-7988 ALABAMA Mobile Tuscaloosa 36618 35405 Azalea City Service Ctr. Lighting Plus 251-341-0663 205-345-8900 ARIZONA Green Valley Mesa Mesa Phoenix Phoenix Prescott Scottsdale Sedona Tucson Tucson Tucson Youngtown Yuma 85614 85204 85210 85032 85019 86305 85254 86336 85735 85716 85711 85363 85364 Goble Electric Gallery of Fans Loud Inc. dba Fans Plus Brasswinds Fan Doctor Fantastic Electric Marc Parent Vandervoort Electric Oak Creek Audio Desert Breeze Fan & Elec. Illuminations Sun Lighting Company Brasswinds Fan Doctor Curley’s Litehouse 520-625-4938 480-962-0477 480-827-9302 602-482-1881 602-866-1090 928-778-5935 602-996-9637 928-282-5625 520-623-4646 520-325-3031 520-322-4303 623-933-0240 928-783-6931 ARKANSAS Little Rock 72212 The Randy Hall Co. Inc. 501-227-9915 CALIFORNIA Auburn Bakersfield Bakersfield Cathedral City Cerritos Chico Clovis Folsom Fresno Fresno Fresno Glendale Grass Valley Huntington Beach Jamestown Los Alamitos Manteca Mission Viejo Modesto Moorpark Murrieta Newhall (Santa Clarita) Pleasanton Rancho Mirage Redding Riverside Sacramento San Diego San Francisco San Marcos San Marcos San Rafael Santa Clara Santa Cruz Santa Maria Santa Rosa Saugus Shingle Springs South Lake Tahoe Stockton Tarzana Temecula Tulare Valencia 95603 93306 93309 92234 90703 95928 93612 95630 93711 93704 93710 91208 95945 92647 95327 90720 95336 92691 95350 93021 92562 91321 94588 92270 96002 92505 95819 92111 94109 92069 92069 94901 95051 95062 93455 95404 91350 95682 96150 95205 91356 92592 93274 91354 The Fan Doctor Hillcrest Lighting RB Electric & Lighting R & R Service Comforts of Home J & J Lighting Omega Services Inc. Folsom Lighting Co. James & Co. Lighting Larry McCollum The Energy Saving House Fantastic Fan Service Accent Lighting Trading Post Fan Company Da Silva’s Lamp & Clg. Jaben Holdings Manteca Lighting Moore’s Sew, Vac, & Fan Phillips Lighting & Home R.J. Sieg Elect. Co. Fan Diego Dan Martin S & L Lighting Services Fan Diego North Valley Lighting Verne Smith A & A Light Fixtures Fan Diego House of Fans Inc. Fan Diego RD Electrical Cont. Raffles Fans Sal Zamora’s Fan Repair Riverside Lighting Ever-Ready Electric Asef’s Appl. & Elec. Svc. Valley Breeze Fan Co. John Rozowski Const. Tahoe Pool Service Risso Electric Hye Lighting Co. Tab Electric Anchor Lighting Fantastic Fan Service 530-823-8768 661-324-0649 661-831-2438 760-324-2942 562-865-6666 530-342-1815 559-299-0495 916-983-5575 559-486-7900 559-438-5764 559-432-1500 800-800-3871 530-477-5483 714-848-4353 209-984-4035 562-594-1249 209-823-1999 949-580-2520 209-524-6287 805-523-7434 951-600-7867 661-252-5769 925-895-3762 760-779-9916 530-221-6277 951-687-9552 916-452-7641 858-292-9244 415-885-1947 760-743-3267 760-727-1215 415-456-6660 510-742-5560 831-423-7411 805-934-7091 707-575-3737 800-339-3267 530-677-3850 530-541-4958 209-466-0781 818-345-5544 951-303-0850 559-688-0696 800-800-3871 COLORADO Colorado Springs Denver Fort Collins Longmont 80903 80229 80525 80504 Home Lighting M.D Electric Light Center L A Enterprises 719-471-3520 303-288-7988 970-226-3430 800-299-0222 TYPE WTS WTS ISO ISO ISO ISO, WTS ISO ISO ISO ISO ISO, WTS WTS ISO, WTS ISO ISO, WTS ISO ISO ISO ISO ISO ISO WTS ISO, WTS WTS WTS WTS TYPE OF SERVICES OFFERED: ISH = IN-HOUSE SERVICE 14 ISO = IN-SHOP ONLY WTS = SERVICES ONLY WHAT THEY SELL STATE/CITY SERVICE CENTER NAME PHONE TYPE COLORADO (Continued) Longmont 80501 Loveland 80538 ZIP Lumenarea.com, Inc. Fireside Lighting 303-485-6800 970-669-3540 WTS WTS CONNECTICUT Bridgeport Clinton East Hartford Greenwich Hartford New Hartford New Haven Willington Woodstock 06605 06413 06118 06830 06114 06057 06511 06279 06281 Federal Elect. Const. Co. Graham Co. Graham Co. Fashion Light Center Connecticut Ltg. Center B.W. Morse & Sons Inc. New Grand Light George Opalenik Randy Matteau 203-334-6455 800-942-5575 800-942-5575 203-869-3098 ISO, WTS 860-249-7631 ISO 860-379-9855 203-777-5781 ISO 860-684-4558 860-963-8979 DELAWARE Dover New Castle 19901 19720 Bruce Drajem Eric Shurr 302-734-7737 302-998-5147 DISTRICT OF COLUMBIA Washington 20007 Fan Fair 202-342-6290 FLORIDA Bonita Springs Boynton Beach Brandon Coral Gables Davie Fern Park Gainesville Jacksonville Maitland Naples Nokomis Orlando Port Charlotte S. Daytona Spring Hill Tallahassee Tarpon Springs Winter Haven Winter Haven 34135 33437 33511 33134 33330 32730 32608 32217 32751 34109 34275 32806 33952 32119 34606 32303 34689 33880 33884 Goodwin Electric CMS Lumenair Lighting & Fan Michael Hansen Laserland Inc. Henry Electric Co. Authorized Appliance Authorized Appliance Serv. Henry Electric Co. Wilson Fans & Lighting Graham Electrical Cont. Mid-Florida Fan Jacksons Lighting Bob’s Fix-It Fan Doctor Jim Laczko Peter Lontakos All About Fans Cypress Ltg. Showroom 239-649-8880 561-736-0170 813-653-3460 ISO 305-444-4111 954-558-3743 407-834-4032 ISO 352-375-3886 ISO 904-737-5312 ISO 407-834-4032 ISO 239-592-6006 ISO, WTS 941-486-8190 407-893-6226 941-625-0044 WTS 386-761-4055 352-683-4428 850-562-4661 727-938-8895 863-299-9593 863-676-9097 GEORGIA Grayson 30017 RG Tenney Electric 770-378-9255 HAWAII Aiea Hilo Kahului Kailua-Kona Kaulua Kona Kihei 96701 96720 96732 96740 96740 96753 Fan Shop Inc. Bay Lighting & Design Read Lighting Kona Coast House of Lights Ku’s Electronic Service Fans Etc. 808-488-1221 808-961-5688 808-871-8995 808-329-0748 808-329-4346 808-875-6347 IDAHO Idaho Falls Meridian 83402 83642 Home Lighting S-K Electric, Inc. 208-523-2300 208-941-6264 ILLINOIS Centralia Champaign Champaign Chicago Cornland Frankfort Mchenry Mokena Normal Princeton Quincy Smithton Trenton Urbana Yorkville 62801 61821 61821 60630 62519 60423 60051 60448 61761 61356 62305 62285 62293 61801 60560 Baker Appliance Repair Springfield Electric Supply Terry Gobble D & S Fan Specialist Delmar Veech KKA Services Northwest Electrical KKA Services Kirk Small Appliance Elmore Electric Inc. Heintz Lighting Center John Hassenstab Light Brite Distributing Terry Gobble Unified Supply, Inc. 618-532-8437 217-351-7600 217-384-5891 847-824-2430 217-364-4124 815-464-6714 815-363-1800 815-464-6714 309-452-5248 815-643-2354 217-223-0101 618-236-3018 618-224-7314 217-384-5891 630-553-0660 INDIANA Evansville Fort Wayne Greenfield Indianapolis Valparaiso 47711 46805 46140 46222 46383 Michael Baxter Carl Smith D & D Repair Indiana Lighting Center D & K Electric 812-453-6498 260-484-7295 317-467-0600 317-293-9333 219-464-7576 ISO WTS ISO ISO ISO ISO ISO HAMPSHIRE™ STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE IOWA Carroll Cedar Rapids Coralville Davenport Des Moines Monticello Sioux Center Sioux City 51401 52404 52241 52803 50311 52310 51250 51106 J & L Electric Inc. Acme Electric Company Ralston Creek Shaw Electric Advanced Lighting Rem Electric Hills Home Systems Diversified Electronics 712-792-2444 ISO 319-365-8677 319-351-2189 ISO, WTS 563-323-3611 515-255-5009 WTS 319-465-3346 712-722-4905 712-276-1034 KANSAS Emporia Lenexa Manhattan Overland Park Overland Park Overland Park Overland Park Salina Wichita 66801 66215 66502 66213 66210 66223 66212 67401 67208 C.A.P. Rensen House Of Lights Endacott Lighting Kal Electric Randy Russell Western Chandelier Co. Wilson Fans & Lighting Salina Appliance Showroom Accent Lighting 620-342-0448 913-888-0888 785-776-4472 913-897-6767 913-338-5330 913-685-2000 913-642-1500 785-827-1420 316-636-1278 KENTUCKY Louisville 40205 Kaelins, Inc. 502-454-8938 LOUISIANA Baton Rouge Houma Lafayette Lake Charles Metairie Monroe New Iberia 70815 70363 70501 70601 70006 71201 70560 Total Home Service Gulf South Armature Inc. Acadia Service Co. Josephs Electrical Center Romaine’s Albert Surlco Walet’s Inc. 225-272-7725 985-872-0486 337-233-8910 337-436-4930 504-887-7077 318-699-0619 337-364-7486 MAINE South Portland 04106 T.A. Napolitano Inc. 207-799-0538 MARYLAND Forestville Frederick Fulton White Hall 20747 21704 20759 21161 Burgess Lighting & Dist. GL Fan Service GL Fan Service BT Electric 301-568-8000 ISO, WTS 301-831-4925 IHS 301-831-4925 IHS 410-329-6353 MASSACHUSETTS Belmont Bridgewater Cochituate Danvers Dennis Natick New Bedford Orleans S. Attleboro W. Springfield Worcester 02478 02324 01778 01923 02638 01760 02740 02653 02703 01089 01603 H.O Electric Biltcliffe Electric J.G. Electric Co. Inc. Plaza Lighting Rick Sexton J.G. Electric Co Inc. Vander Electric & Equipment Associated Electrical A J Electric Jalbert Electric Edward A. Tortora 617-489-6324 508-697-7630 508-653-3042 978-774-7801 508-385-7536 508-653-3042 508-993-6383 508-255-4589 508-761-5021 413-734-4976 508-755-3735 MICHIGAN Belleville Birmingham Grand Rapids Howell Lansing Lansing Portage Traverse City 48111 48009 49512 48855 48906 48917 49024 49686 Mike Ayerst 21st Century Electric Grand Rapids Lighting Ctr. Lightning Elec. Inc. Integrity Electric Inc. Largent Enterprises Hodgson Light & Log Lighting & Fan Service 734-699-9698 248-645-6464 616-949-4931 ISO, WTS 810-227-3375 517-484-0300 517-327-6161 800-451-0860 WTS 231-938-1332 MINNESOTA Baxter Burnsville Eden Prairie Maplewood Minneapolis Minneapolis Rochester 56425 55336 55344 55109 55422 55411 55906 The Light Depot Fan Man Fan Man North Country Electric Leo’s Elec. Sales & Service Penn Elec. Motor Service Kroupa’s Electronics 218-829-0770 952-898-2754 952-941-9243 651-486-7099 763-546-5625 612-588-5333 507-361-1280 MISSISSIPPI Madison 39110 Jackson Service Ctr. 601-856-9469 MISSOURI Branson Springfield St. Louis 65616 65807 63123 The Light House Gallery/Loyds The Light House Gallery/Loyds Leinweber Service Co. 417-334-2171 417-334-2171 314-892-8177 MONTANA Helena Kalispell 59601 59901 Supreme Lighting Lasalle Lighting 406-442-8200 406-752-2424 IHS ISO ISO ISO ISO IHS ISO ISO ISO ISO ISO ISO ISO ISO ISO ISO STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE MONTANA (Continued) Missoula 59801 Western Montana Lighting Supply 406-543-7166 ISO NEBRASKA Grand Island Lincoln Norfolk Omaha Omaha 68803 68510 68701 68104 68144 Quality Sew & Vac Lincoln Lighting Center The Power Station D & L Electronics Oak Hills Electric Inc. 308-382-7310 402-476-1297 402-371-6671 402-571-5233 402-691-4567 ISO NEVADA Henderson Las Vegas Sparks 89015 89119 89431 KS & S Electric, LLC Fanco Eagle Electric, Inc. 702-222-9306 702-898-8522 775-356-7300 NEW HAMPSHIRE Nashua Newmarket 03060 03857 Affordable Fans Etc. Edward Heine 603-759-8332 603-659-5999 NEW JERSEY Chester Hillsborough Jackson Linwood Morris Plains Mullica Hill Park Ridge Randolph Thorofare Trenton W. Long Branch Washington 07930 08844 08527 08221 07950 08062 07656 07869 08086 08619 07764 07882 Chester Lighting, Inc. Top Line Electric Robert Rolzhausen Jack Breslau Manny Herrera Stephen Rice Krell Lighting Anthony Makomaski Harry R. Habicht Wiring Unlimited No Shorts Electric C.P. Orlando 908-879-7200 908-431-1888 732-363-3729 609-601-1797 973-993-1137 856-223-8645 201-391-7685 908-475-5569 856-845-2541 609-584-1122 732-222-4228 908-689-4750 NEW MEXICO Albuquerque Albuquerque Albuquerque 87112 87109 87123 A-1 Lamp Doctor B-Electric Inc. Frank’s Electric LLC 505-296-5050 505-828-0241 505-293-6724 NEW YORK Amherst Amherst Bedford Hills Brooklyn Brooklyn Brooklyn Buffalo Buffalo Carle Place Commack Commack East Meadow Glens Falls Hastings Long Beach Lynbrook New York Newburgh Plainview Poughkeepsie Queensbury Rego Park Rochester Schenectady Shokan Staten Island Staten Island Staten Island Troy Yonkers 14226 14228 10507 11204 11219 11223 14206 14215 11514 11725 11725 11554 12801 13076 11561 11563 10003 12550 11803 12601 12804 11374 14620 12303 12481 10301 10312 10304 12180 10704 Royalite Lighting Shanor Lighting Center Bedford Ltg Jerry Piccolino/J&R Svc. Main Lamp Corp. Manhattan Lights Craftmasters Servicenter The Fan Collection, Inc. Elements Air-Tek Turnpike Appliance C.D. Service Dean Electric Electrical Work By Marty Nick’s Improvement Company Shaderite-PZ Repair Superior Light & Fan J D Parrella Electric Joseph Gottdank Mannino Electric Inc. Dean Electric Mark Ralin Cam Electric Frank Salvatore Olive Fans & Lighting Frank Ragucci Joe Valletutti Jr. V & P Service Co. Troy Light Company Jay D. Kosack 716-832-1492 716-691-3622 914-666-0680 718-259-1789 718-436-8500 718-998-1111 716-893-9557 716-839-2447 516-747-4748 631-499-1854 631-499-3355 516-538-3481 518-792-4781 315-668-0220 516-659-8989 516-593-8973 212-677-9191 845-562-4112 516-932-7618 845-452-3520 518-792-4781 718-896-7844 585-271-8560 518-355-5789 845-657-5823 718-273-5518 718-608-9008 917-751-2562 518-274-6931 914-237-9051 NORTH CAROLINA Charlotte Charlotte Hickory Salisbury 28205 28203 28602 28146 Efird’s Interiors Inc. Simpsons Lighting Efird’s Interiors Inc. Hauss Electrical Svc. 704-376-5648 704-376-5463 828-322-2203 704-637-7774 NORTH DAKOTA Fargo 58103 JDP Electric Inc. 701-293-0441 OHIO Canton Cleveland Columbus Dayton 44706 44109 43231 45419 Appliance Parts Co. Westside Lighting Ctr. The Lamp Lighter Larkin Electric Co. 330-453-8077 216-459-1970 614-891-7940 937-294-4115 ISO WTS IHS WTS ISO ISO ISO ISO ISO ISO ISO ISO ISO ISO ISO ISO WTS ISO ISO 15 STATE/CITY ZIP SERVICE CENTER NAME PHONE OHIO (Continued) Dayton Galena Loveland Maumee North Lima North Olmsted 45459 43021 45140 43537 44452 44070 Ohio Lamp & Fixture Co. Certified Systems Hank Grinshpan K.O.V. Electronic Repair Joe Dickey Electric Chandelier Shack Inc. 937-439-0822 614-799-0878 513-683-8666 419-865-8893 330-549-3976 440-777-6969 OKLAHOMA Oklahoma City Oklahoma City 73105 73127 Appliance Service By CK James Lighting Inc. 405-525-8862 405-947-6663 OREGON Portland 97225 Sylvan Electronics Inc. 800-473-1244 PENNSYLVANIA Allentown Allentown Conshohocken Downingtown Drexel Hill Easton Fairless Hills Harrisburg Hopwood Lancaster Philadelphia Pittsburgh State College West Reading Willow Grove 18105 18102 19428 19335 19026 18045 19030 17111 15445 17601 19111 15224 16803 19611 19090 Lighting Fixture & Supply Scholl’s Electric Kay Elec. Supply Tobias Electric Patrick Hastings Primrose Electric Astro Lighting Galleries Yale Electric Supply Co. George R. Smalley Inc. S. Dean’s Electric Klaus Otte Mark Diulus Elec. Whitehill Lighting & Supply A TO Z Vacuum Stores Northwest Electric 610-435-9691 610-435-5876 800-331-5111 610-942-4000 610-853-2709 610-258-1359 215-943-8650 717-233-8401 724-437-1927 717-285-4545 215-745-4266 412-681-2553 814-238-2449 610-374-4888 215-659-5757 RHODE ISLAND Pawtucket 02861 Wickford Appliance 401-726-4240 SOUTH CAROLINA Columbia Goose Creek Hanahan Ladson Myrtle Beach Okatie Spartanburg Sioux Falls Sioux Falls 29212 29445 29406 29456 29575 29909 29306 57105 57104 Eastwind Enterprises David Mims Bobby Lutes Electrical Bobby Lutes Electrical Ray Electric J. Heavener & Co. Bobby Jackson Electr. Lamps and Shades Inc. Mahlander’s 803-781-3267 843-514-2380 843-832-2058 843-832-2058 843-293-0068 843-837-8300 864-583-6035 605-332-6680 605-336-7798 TENNESSEE Brentwood Maryville Memphis Mount Carmel 37027 37803 38111 37645 Sunshine Electrical Ben Snyder Appliance Service Ctr. Appalachian Electronics Svc. 615-371-9383 865-385-1302 901-324-5898 423-357-0783 TEXAS Amarillo Arlington Austin Austin Beaumont Carrollton Corpus Christi Dallas Damon Denton Denton 79106 76001 78757 78703 77702 75006 78404 75206 77430 76201 76201 DI’s Lamp & Fan Repairs P & M Quality Const. Klock Electric Texas Ceiling Fan Shop Fan Factory Adfantage Ceiling Fans Brand Appliance & Microwave Lights Fantastic Gulf Coast Fan Svc. Fantasia Ceiling Fans Larry W. Goff 806-331-5267 817-478-2004 512-837-4704 512-477-3132 409-833-8207 972-446-9393 512-854-1851 214-369-1101 281-495-6434 940-484-4222 940-387-7304 TYPE ISO ISO ISO ISO IHS ISO ISO WTS ISO ISO ISO ISO ISO ISO ISO STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE TEXAS (Continued) Denton Freeport Harlingen Hearne Houston Houston Houston Humble Hurst Kerrville Mcallen Paris Richardson San Angelo San Antonio Tyler Victoria Wichita Falls 76201 77541 78550 77859 77089 77069 77063 77338 76053 78028 78504 75460 75080 76903 78212 75707 77904 76308 Southern Comforts Skip’s Electric & Air The Light House Thompson Supply Bennett Fan Install. Inc. Champions Lighting Lighting Plus Carol’s Lighting & Fan Shop Arc Fan & Lighting Maurice Hammit The Light House Hargis Electric Cool Breezes Heritage Haus Ceiling Fan Service Ctr. Charles Rains Hall Electric Lantern House 940-536-1406 979-233-3903 956-423-6664 WTS 979-280-5737 281-484-1401 281-440-5339 ISO 713-784-2440 ISO 281-446-7613 ISO 817-268-2218 ISO, WTS 830-367-4937 956-631-1155 WTS 903-785-8055 972-690-4580 325-655-4900 210-804-1362 903-566-3119 361-578-6221 940-692-7381 ISO UTAH Layton Murray Riverton 84040 84107 84065 Haruo Yoshikawa Central Electric Co. Inc. Vern O. Francis 801-546-6008 801-467-5479 801-254-4178 VERMONT Bolton Valley 05477 Joseph Ashley 802-434-6510 VIRGINIA Burke Rapidan Richmond Virginia Beach Williamsburg 22015 22733 23228 23451 23185 L & S Electric Inc. Ceiling Fan Installations, Inc. Fanning Elec. Svc. Fans, Lighting ‘N More Taproot Co. 703-237-0011 866-631-6565 804-262-3681 757-422-3616 757-229-3722 ISO WASHINGTON Pasco Spokane Tacoma Wenatchee Yakima 99301 99216 98404 98801 98902 Total Service Inc. Brite-Way Electric M.G.M. Electronics Sew Creative Advantage Store Inland Lighting 509-547-3799 509-939-3995 253-752-9826 509-663-5516 509-248-4647 ISO WEST VIRGINIA South Charleston Wheeling 25309 26003 Pepper Electric Top Hat Stove Sales 304-768-8195 304-233-6262 WISCONSIN Brookfield Fontana Green Bay La Crosse Madison Milwaukee 53005 53125 54313 54601 53719 53219 City Lights Design Showroom J&L Property Maint. Karl Devroy Wettstein’s Madison Lighting Bob’s Fan Repair 262-781-9048 ISO, WTS 262-275-2345 920-494-6090 608-784-5555 608-271-6911 414-546-2501 CANADA Toronto, Ontario M6M2P5 Zaneen Lighting Inc. 800-388-3382 ISO OVERSEAS St. Thomas, Virgin Islands 00805 Duane Loberg 304-775-2399 PRODUCT SPECIFICATIONS Collection: Model Name: Model Number: Casablanca Designer Hampshire C7K62M Dimensions: A = 12" B = 7" C = 3" D = 16" E = 6" NOTE: Dimension B includes light fixture and glass. Weight: 16 34 lbs. Finishes: Motor: Blade Span: Blade Options: Blade Iron Pitch: No. of Blades: Technology: Lightbulbs: Distressed Relic 188 x 25mm Direct DriveTM 60" Any 21" badge-type blade 14° 4 Versa•Touch2® W-73 (4) 25-watt mini S-11 for uplight, (2) 60-watt B-10 bulbs for downlight (Candelabra-base)