Download Sharp XV-Z9000E Service manual
Transcript
XV-Z9000U/E SERVICE MANUAL SERVICE-ANLEITUNG S81Y7XVZ9000U DLP PROJECTOR DLP PROJEKTOR MODELS MODELLE XV-Z9000U/E In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen Originalzustand gebracht werden. Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet werden. SHARP CORPORATION This document has been published to be used for after sales service only. 1The contents are subject to change without notice. XV-Z9000U/E CONTENTS Page • • • • • • • • • • • • • Page SPECIFICATIONS ............................................. 3 INPOTANT SERVICE SAFETY NOTES ............ 4 OPERATION MANUAL ...................................... 8 REMOVING OF MAJOR PARTS ..................... 14 RESETTING THE TOTAL LAMP TIMER ......... 20 THE OPTICAL UNIT OUTLINE ........................ 21 ELECTRICAL ADJUSTMENT .......................... 24 TROUBLE SHOOTING TABLE ........................ 32 CHASSIS LAYOUT .......................................... 92 BLOCK DIAGRAM ........................................... 94 OVERALL WIRING DIAGRAM ........................ 96 DESCRIPTION OF SCHEMATIC DIAGRAM ... 98 WAVEFORMS .................................................. 99 • SCHEMATIC DIAGRAM ................................ • PRINTED WIRING BOARD ASSEMBLIES ... • PARTS LIST Ë ELECTRICAL PARTS ............................... Ë CABINET AND MECHANICAL PARTS .... Ë ACCESSORIES PARTS ........................... Ë PACKING PARTS ..................................... • PACKING OF THE SET ................................. 100 133 140 154 158 158 159 INHALT Seite • TECHNISCHE DATEN ..................................... • HINWEISE FÜR DAS WARTUNGSPERSONAL ................................. • BEDIENUNGSANLEITUNG ............................. • ENTFERNEN DER HAUPTTEILE ................... • RÜCKSTELLEN DES LAMPENBETRIEBSZEIT-TIMERS .................. • BESCHREIBUNG DER OPTIK-EINHEIT ........ • ELEKTRISCHE EINSTELLUNG ...................... • FEHLERSUCHTABELLE ................................. • CHASSIS-ANORDNUNG ................................ • BLOCKSCHALTBILD ....................................... • GESAMTSCHALTPLAN ................................... Seite 49 • BESCHREIBUNG DES SCHEMATISCHEN SCHALTPLANS ............................................... 98 • WELLENFORMEN ........................................... 99 • SCHEMATISCHER SCHALTPLAN ................ 100 • LEITERPLATTENEINHEITEN ....................... 133 • ERSATZTEILLISTE Ë ELEKTRISCHE BAUTEILE ...................... 140 Ë CEHÄUSE UND MECHANISCHE BAUTEILE ................................................ 154 Ë ZUBEHÖRTEILE ...................................... 158 Ë VERPACKUNGSTEILE ............................ 158 • VERPACKEN DES GERÄTS ......................... 159 50 51 57 63 64 67 75 92 94 96 2 XV-Z9000U/E Specifications Product type Model Video system Computer Display method DMD panel Lens Projection lamp Contrast ratio Video input signal S-video input signal Component input signal Horizontal resolution DC output Computer RGB input signal Wired Remote Control Pixel clock Vertical frequency Horizontal frequency Computer control signal Rated voltage Input current Rated frequency Power consumption Operating temperature Storage temperature Cabinet I/R carrier frequency Dimensions (approx.) Weight (approx.) Supplied accessories Replacement parts DLP Projector XV-Z9000U/E PAL/PAL 60/PAL- M/PAL- N/SECAM/NTSC 3.58/NTSC 4.43/DTV 480I/DTV 480P/DTV 720P/DTV 1080I VGA/SVGA/XGA/SXGA Single panel Digital Micromirror Device™(DMD™) by Texas Instraments Panel size:0.8" (20.3mm) No.of dots:921,600 dots (1280 [H ] X 720 [V ]) 1 – 1.35X zoom lens, F3, f = 32.5 – 44.0 mm 250 W NSH lamp 1000:1 RCA Connector:VIDEO,composite video,1.0 Vp-p,sync negative,75 Ω terminated (INPUT 4) 4-pin Mini DIN connector (INPUT 3) Y (luminance signal):1.0 Vp-p,sync negative,75 Ω terminated C (chrominance signal):Burst 0.286 Vp-p,75 Ω terminated RCA connector (INPUT 1 and 2 terminals) Y:1Vp-p, sync negative, 75 Ω terminated PB/PR:0.7Vp-p, 75 Ω terminated (XV-Z9000U) CB/CR:0.7Vp-p, 75 Ω terminated (XV-Z9000E) 720 TV lines (DTV 720P input) 12V. MAX CURRENT 200mA CENTER + TYPE 15-PIN MINI D-SUB CONNECTOR (INPUT 5 port): RGB separate/composite sync/sync on green type analog input:0 – 0.7 Vp-p,positive, 75 Ω terminated HORIZONTAL SYNC.SIGNAL:TTL level (positive/negative)or composite sync (Apple only) VERTICAL SYNC.SIGNAL:Same as above 3.5 ø Mini jack 12 – 120MHz 43 – 100Hz 15 – 80 kHz 9-pin D-Sub male connector (RS-232C port) AC 100 – 240 V 3.6 A 50/60 Hz 345 W (Selecting "BRIGHT" in the "Theater Mode".) + 5 °C to + 35 °C (41 °F to + 95 °F ) − 20 °C to + 60 °C (− 4 °F to + 140 °F) Plastic 38 kHz 18 11⁄16" (W) X 7" (H) X 15 15⁄50" (D)(475 X 178 X 406mm)(main body only) 18 11⁄16" (W) X 8" (H) X 19 1⁄2" (D)(475 X 203 X 496 mm)(including terminal cover and adjustment feet) 20.9 lbs.(9.5 kg) Remote control, Two AA size batteries, Power cord (11' 10" ,3.6 m(XV-Z9000U), 1.8m(XV-Z9000E)), Lens cap (attached), DLP projector operation manual, CD-ROM, CD-ROM operation manual, Terminal cover, Video cable(XV-Z9000E), VGA cable(XV-Z9000E), 21pin-RCA adaptor(XVZ9000E), Guarrantee card for U.S., Guarrantee card for CANADA. Lamp unit (Lamp/cage module) (BQC-XVZ9000/1), Remote control (RRMCG1657CESA), AA size batteries, Power cord (CACCU5013DE01 (XV-Z9000U), QACCV4002CEZZ (XV-Z9000E), QACCB5024CENA (XV-Z9000E)), Lens cap (PCAPH1056CESA),DLP projector operation manual (TINS-7415CEZZ (XV-Z9000U), TINS-7521CEZZ (XV-Z9000E)), CD-ROM(UDSKA0047CEN1), CD-ROM operation manual (TINS-7418CEZZ (XV-Z9000U), TINS-7523CEZZ (XV-Z9000E)), Video cable(QCNWGA001WJZZ(XV-Z9000E)), VGA cable(QCNW-5050CEZZ(XV-Z9000E)), 21pin-RCA adaptor(QSOCZ0361CEZZ(XV-Z9000E)), Guarrantee card for U.S.(TGAN-1670CEZZ), Guarrantee card for CANADA (TGAN-1671CEZZ). This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen.This will not affect the picture quality or the life expectancy of the unit. If you have any questions about this matter,please call toll free 1888-GO-SHARP (1-800-237-4277). U.S.A.ONLY This SHARP projector uses a DMD panels.This very sophisticated panels contain 921,600 pixels. As with any high technology electronic equipment such as large screen TVs,video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. Specifications are subject to change without notice. 3 XV-Z9000U/E IMPORTANT SERVICE SAFETY NOTES (for USA) Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per volt., or higher, sensitivity to measure the AC voltage drop across the resistor (See Diagram). » All checks must be repeated with the AC plug connection reversed. (If necessary, a non-polarized adapter plug must be used only for the purpose of completing these checks.) Any reading of 0.3 volts RMS (this corresponds to 0.2 milliamp. AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the unit to the owner. WARNING 1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. BEFORE RETURNING THE PROJECTOR: (Fire & Shock Hazard) Before returning the projector to the user, perform the following safety checks: 1. Inspect lead wires are not pinched between the chassis and other metal parts of the projector. 2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc. 3. To be sure that no shock hazard exists, check for current leakage in the following manner: » Plug the AC cord directly into a 120-volt AC outlet, (Do not use an isolation transformer for this test). » Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in parallel between all exposed metal cabinet parts and earth ground. AC VOLTMETER 1.5k ohm (10W) 0.15µF TEST PROBE TO EXPOSED METAL PARTS CONNECT TO KNOWN EARTH GROUND 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 SAFETY NOTICE AVIS POUR LA SECURITE Many electrical and mechanical parts in DLP Projector have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by “å” and shaded areas in the Replacement Parts Lists and Schematic Diagrams. For continued protection, replacement parts must be identical to those used in the original circuit. The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire or other hazards. De nombreuses pièces, électriques et mécaniques, dans les projecteur à DLP présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des pièces de remplacement étalonnées pour haute tension, puissance, etc. Les pièces de remplacement qui présentent ces caractéristiques sont identifiées dans ce manuel; les pièces électriques qui présentent ces particularités sont identifiées par la marque “å” et hachurées dans la liste des pièces de remplacement et les diagrammes schématiques. Pour assurer la protection, ces pièces doivent être identiques à celles utilisées dans le circuit d’origine. L’utilisation de pièces qui n’ont pas les mêmes caractéristiques que les pièces recommandées par l’usine, indiquées dans ce manuel, peut provoquer des électrocutions, incendies ou autres accidents. WARNING: The bimetallic component has the primary conductive side exposed. Be very careful in handling this component when the power is on. AVERTISSEMENT: La composante bimétallique dispose du conducteur primaire dénudé. Faire attention lors de la manipulation de cette composante sous tension. 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 4 XV-Z9000U/E NOTE TO SERVICE PERSONNEL 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 NOTE POUR LE PERSONNEL D’ENTRETIEN 12345678901234567890123456789012123456789012345 UV-RADIATION PRECAUTION 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 PRECAUTION POUR LES RADIATIONS UV 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 The light source, lamp, in the projector emits small amounts of UV-Radiation. La source de lumière, la lampe , dans le projecteur émet de petites quantités de radiation UV. AVOID DIRECT EYE AND SKIN EXPOSURE. EVITEZ TOUTE EXPOSITION DIRECTE DES YEUX ET DE LA PEAU. To ensure safety please adhere to the following: Pour votre sécurité, nous vous prions de respecter les points suivants: 12345678901234567890123456789012123456789012345 1. Toujours porter des lunettes de soleil lors d’un entretien du projecteur avec la lampe allumée et le haut du coffret retiré. 1. Be sure to wear sun-glasses when servicing the projector with the lamp turned “on” and the top enclosure removed. 2. Ne pas faire fonctionner la lampe à l’extérieur du boîtier de lampe. 2. Do not operate the lamp outside of the lamp housing. 3. Ne pas faire fonctionner plus de 2 heures avec le coffret retiré. 3. Do not operate for more than 2 hours with the enclosure removed. Précautions pour les radiations UV et la lampe moyenne pression UV-Radiation and Medium Pressure Lamp Precautions 1. Toujours débrancher la fiche AC lors du remplacement de la lampe. 2. Laisser l’unité refroidir pendant une heure avant de procéder à l’entretien. 3. Ne remplacer qu’avec une lampe du même type. Type BQC-XVZ9000/1, caractéristique 355V/250W. 4. La lampe émet de petites quantités de radiation UVéviter tout contact direct avec les yeux. 5. La lampe moyenne pression implique un risque d’explosion. Toujours suivre les instructions d’installation décrites ci-dessous et manipuler la lampe avec soin. 1. Be sure to disconnect the AC plug when replacing the lamp. 2. Allow one hour for the unit to cool down before servicing. 3. Replace only with same type lamp. Type BQCXVZ9000/1 rated 355V/250W. 4. The lamp emits small amounts of UV-Radiation, avoid direct-eye contact. 5. The medium pressure lamp involves a risk of explosion. Be sure to follow installation instructions described below and handle the lamp with care. 5 XV-Z9000U/E 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 UV-RADIATION PRECAUTION (Continued) 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 PRECAUTION POUR LES RADIATIONS UV (Suite) 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Lamp Replacement Remplacement de la lampe Note: Remarque: Since the lamp reaches a very high temperature during units operation replacement of the lamp should be done at least one hour after the power has been turned off. (to allow the lamp to cool off.) Installing the new lamp, make sure not to touch the lamp (bulb) replace the lamp by holding its reflector 2. [Use original replacement only.] Comme la lampe devient très chaude pendant le fonctionnement de l’unité, son remplacement ne doit être effectué au moins une heure après avoir coupé l’alimentation (pour permettre à la lampe de refroidir). En installant la nouvelle lampe, s’assurer de ne pas toucher la lampe (ampoule). Remplacer la lampe en tenant son réflecteur 2. [N’utiliser qu’un remplacement d’origine.] 1 Lampe 1 Lamp 2 Reflecteur 2 Reflector DANGER ! –– Never turn the power on without the lamp to avoid electric-shock or damage of the devices since the stabilizer generates high voltages at its start. DANGER ! –– Ne jamais mettre sous tension sans la lampe pour éviter un choc électrique ou des dommages des appareils car le stabilisateur génère de hautes tensions à sa mise en route. Since small amounts of UV-radiation are emitted from an opening between the exhaust fans, it is recommended to place the cap of the optional lens on the opening during servicing to avoid eye and skin exposure. Comme de petites quantités de radiation UV sont émises par une ouverture entre les ventilateurs aspirants, il est recommandé de placer le capuchon de l’optique optionnelle sur l’ouverture pendant l’entretien pour éviter une exposition des yeux et la peau. 6 XV-Z9000U/E WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS. CAUTION The lighting flash with arrowhead within a triangle is intended to tell the user that parts inside the product are risk of electric shock to persons. RISK OF ELECTRIC SHOCK. DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREW CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE CABINET. NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the manual with the projector. CAUTION (POWER Unit) For continued protection against risk of fire, replace only with same type and rating of fuse. (F7001, F7002) 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 AVERTISSEMENT: Source lumineuse de grande intensité. Ne pas fixer le faisceau lumineux ou le regarder directement. Veiller particulièrement à éviter que les enfants ne fixent directement le faisceau lumineux. AVERTISSEMENT: AFIN D’EVITER TOUT RISQUE D’INCENDIE OU D’ELECTROCUTION, NE PAS PLACER CET APPAREIL DANS UN ENDROIT HUMIDE OU MOUILLE. ATTENTION L’éclair terminé d’une flèche à l’intérieur d’un triangle indique à l’utilisateur que les pi‘eces se trouvant dans l’appareil sont susceptibles de provoquer une décharge électrique. RISQUE D’ELECTROCUTION NE PASRETIRER LES VIS, A L’EXCEPTION DES VIS DE REPARATION UTILISATEUR SPECIFIEES Le point d’exclamation à l’intérieur d’un triangle indique à l’utilisateur que les instructions de fonctionnement et d’entretien sont détaillées dans les documents fournis avec le projecteur. ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION, NE PAS RETIRER LE CAPOT. AUCUNE DES PIECES INTERIEURES N’EST REPARABLE PAR L’UTILISATEUR, A L’EXCEPTION DE L’UNITE DE LAMPE. POUR TOUTE REPARATION, S’ADRESSER A UN TECHNICIEN D’ENTRETIEN QUALIFIE. PRECAUTION (Unite d’admission) Pour une protection continue contre les risques d’incendie, ne remplacer qu’avec un fusible du même type. (F7001, F7002) 7 XV-Z9000U/E Location of Controls Projector Front and Top View Remote control sensor Lens shift dial Zoom knob TEMPERATURE WARNING indicator LAMP REPLACEMENT indicator Focus ring POWER indicator Adjuster Intake ventilative hole Adjuster Remote control sensor Lens cap MENU button RESIZE button ADJUSTMENT buttons ('/"/\/|) INPUT button POWER buttons (ON/OFF) ENTER button UNDO button Side and Rear View 8 XV-Z9000U/E Projector Side and Rear Vie Intake ventilative hole Intake ventilative hole 4 Exhaust ventilative hole Remote control sensor w S-VIDEO INPUT 3 terminal (4-pin Mini DIN) INPUT 5 COMPUTER-RGB port (15-pin Mini D-sub) INPUT 1 COMPONENT/ RGB terminals (RCA) RS-232C port (9-pin D-sub) DC 12 V OUTPUT terminal (200 mA MAX.) XV-Z9000U INPUT 2 COMPONENT/ AC socket RGB terminals (RCA) XV-Z9000E VIDEO INPUT 4 terminal (RCA) 9 Wired remote control jack XV-Z9000U/E Remote Control Front View POWER buttons (ON/OFF) MENU button ENTER button ADJUSTMENT buttons (\/|/'/") UNDO button INPUT 1 button INPUT 3 button INPUT 2 button INPUT 4 button INPUT 5 button THEATER MODE button RESIZE button CLR TEMP buttons GAMMA button KEYSTONE button AUTO SYNC button BACKLIGHT button Top View Remote control signal transmitter Wired remote control jack Insertingthe batteries 1 Pull down the tab on the batterycover and remove the cover towardsthe directionof the arrow. 2 Insert two AA size batteries,makingsure the polaritiesmatch the + and – marks inside the batterycompartment. 3 Insert the lower tab of the batterycover into the opening,and press the cover untilit clicks in place. Battery Battery cover Battery compartment 10 XV-Z9000U/E The remote control can be used to contr ol the projector within the range shown on the left. Remote Control 23 (7 m) 45˚ • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ due to the scr een material. 30˚ 30˚ 45˚ 30˚ Remote Control Using the remote control in a dark room The backlights of the operation buttons can be tur ned on for five seconds and of f by pressing BACKLIGHT. If you want to turn off the backlights while they ar press BACKLIGHT again. BACKLIGHT button Using as a Wired Remote Control When the remote control cannot be used due to the range or positioning of the pr ojector (rear projection, etc.), connect a 3.5 mm stereo minijack cable (commercially available) fr om the wired remote control jack on the top of the remote control to the Wired remote control jack on the back of the projector . 3.5 mm stereo minijack cable (commercially available) 11 XV-Z9000U/E Connection Pin Assignments INPUT 5 RGB Signal Input Port: 15-pin Mini D-sub female connector RGB Input 15 10 5 11 6 1 Analog 1. Video input (red) 2. Video input (green/sync on green) 3. Video input (blue) 4. Not connected 5. Composite sync 6. Earth (red) 7. Earth (green/sync on green) 8. 9. 10. 11. 12. 13. 14. 15. Earth (blue) Not connected GND GND Bi-directional data Horizontal sync signal Vertical sync signal Data clock RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable 3 5 6 1 Pin No. 1 2 3 4 5 6 7 8 9 Signal RD SD SG Name Receive Data Send Data Reserved Signal Ground Reserved Reserved Reserved 12 I/O Input Output Reference Not connected Connected to internal circuit Connected to internal circuit Connected to internal circuit Connected to internal circuit Connected to internal circuit Connected to internal circuit Connected to internal circuit Not connected XV-Z9000U/E Dimensions Rear View Top View Side View 7 (178) 15 49/50 (406) Side View Front View 18 11/16 (475) Bottom View Unit: inches (mm) 13 XV-Z9000U/E REMOVING OF MAJOR PARTS 1. Removing the top panels 1-1. Remove the six lock screw. 1-2. Press on side Arrow A of the bottom body and Lift the rear body. 1-3. Disconnect the connector. 1-4. Press on front Arrow B of the bottom body and unhook the claws, and detach the top body. 2-1. Remove the two screws and detach the LED PWB. 2-2. Remove the one screw and detach the R/C PWB. 2-3. Remove the three screws and detach the operation PWB. 2-1 R/C PWB 2-2 2-3 LED PWB Operation PWB Top body 1-1 1-3 1-4 1-1 1-4 1-1 1-4 B 1-2 A 1-4 B 14 1-1 XV-Z9000U/E 2. Removing the cooling fan and PWB unit assembly. 3-1. 3-2. 3-3. 3-4. Disconnect the eleven connectors. Remove the two screws and detach the lamp socket. Remove the two screws and detach the cooling fan. Remove the four screws and detach the PWB unit assembly. 3-1 3-1 (J5) (RC)(TA) (J2) (FD) (FB) (J3) (DB1) 3-4 (FA) 3-4 3-4 3-3 PWB unit assembly 3-2 LAMP 3-1 Door SW Bi-Metal Cooling Fan 15 XV-Z9000U/E 3. Removing the rear panel, PC unit, cooling duct and main PWB unit. 4-1. 4-2. 5-1. 5-2. 6-1. 7-1. 8-1. 8-2. 8-3. Remove the two screws. Remove the three screws and detach the rear panel. Remove the two screws. Remove the four hexagonal supports and detach the shield plate. Remove the four screws and detach the PC I/F unit. Remove the four screws and detach the cooling duct. Remove the two hexagonal supports. Remove the five screws and detach the main PWB unit. Remove the lock of the holder. 6-1 6-1 PC I/F unit (TB) (EA) (FC) 8-2 8-1 Main PWB unit (EB) (CA) 8-2 7-1 Shield plate Cooling duct 5-2 Rear panel 5-1 5-2 4-1 4-2 8-3 7-1 16 XV-Z9000U/E 4. Removing the power unit shield , power/ballast unit and power unit. 9. Remove the seven screws and detach the power unit shield. 10-1. Remove the two screws. 10-2. Remove the four white supports and detach the power unit. 11. Remove the four screws and detach the power unit. 10-1 Power unit shield Ballast unit 9 11 11 Power unit 10-2 10-2 9 17 XV-Z9000U/E 5. Removing the optical mechanism unit and R/C PWB unit. 12. 13. Remove the six screws and detach the optical mechanism unit. Remove the one screw and detach the R/C PWB unit. 12 12 Optical mechanism unit 12 13 R/C PWB unit 18 XV-Z9000U/E 6. Removing the lamp unit, CW fan, outlet fan, bimetal, wind way duct, shield plate and formater PWB. 14. Remove the three screws and detach the lamp unit. 15. Remove the two screws and detach the CW fan. 16. Remove the three screws and detach the outlet fan. 17-1. Remove the two screws and detach the bimetal. 17-2. Remove the two screws and detach wind way duct. 18-1. Remove the six screws and detach the shield plate(B). 18-2. Remove the three screws and detach the formater PWB. 18-3. Remove the three screws and detach the shield plate(A). Shield Plate(A) Formater PWB 18-3 Shield Plate(B) 18-2 18-2 18-1 17-2 15 Wind way Duct 17-1 Bimetal 14 16 Outlet Fan Lamp unit 19 XV-Z9000U/E Resetting the TOTAL LAMP TIMER ● Resetting the total lamp timer When replacing the lamp, reset the total lamp timer in the procedure below. 1 Plug in the power cord. POWER ON on 2 Press projector to reset lamp timer. While holding down ENTER, [ and >, press POWER ON. ● Light source (lamp) The lamp in this projector operates for approximately 2,000 cumulative hours, depending on the usage environment. (As the usage environment can vary significantly, the projector lamp may not operate for 2,000 hours.) It is recommended that the lamp be replaced after approximately 1,900 cumulative hours of use or when you notice a significant deterioration of the picture and color quality. The lamp usage time can be checked with the On-screen Display. Maintenance Indicator TEMPERATURE WARNING indicator LAMP REPLACEMENT indicator Condition Possible Solution Problem • Blocked air intake. • Relocate the projector to an area with proper ventilation. • Clogged air filter . • Clean the filters. • Cooling fan breakdown. • Internal circuit failure. • Take the projector to your nearest Authorized SharpVision or Service Center or Dealer for repair. The lamp does not light up. • Burnt-out lamp. • Lamp circuit failure. The lamp requires replacement. • Lamp has been used for over 1,900 hours. • Carefully replace the lamp. • Take the projector to your nearest Authorized Sharp Vision Service Center or Dealer for repair. The internal temperature is abnormally high. Condition The LAMP REPLACEMENT indicator lights up red, and “LAMP” and “ ” will flash in yellow in the lower-left corner of the picture. Problem • Lamp has been used for over 1,900 hours. A significant deterioration of the picture and color quality occurs. The power will automatically turn off and the projector will enter stand-by mode. “LAMP” and “ ” will flash in red in the lower-left corner of the picture, and the power will turn off. • Lamp has been used for over 2,000 hours. 20 Possible Solution • Purchase a replacement lamp unit (lamp/cage module) of the current type BQC-XVZ9000/1 from your nearest Authorized SharpVision Service Center or Dealer. • Replace the lamp. If you wish, you may have the lamp replaced at your nearest Authorized SharpVision Service Center or Dealer. XV-Z9000U/E THE OPTICAL UNIT OUTLINE Layout for proper setup of the optical components and parts (top view) Projection lens Prism DMD Chips Condensor lens IR-cut mirror Light tunnel Relay lens Fold mirror Condensor lens Color filter Lamp Item 1 Lamp 2 Condebsor lens, IR-cut mirror and light- tunnel 3 Color filter 4 Relay lens and fold mirror 5 Prism 6 DMD chip 7 Projection lens Descriptions The DC Light source lamp with parabola reflector. The condensor lens leads the light generated from the lamp to the end surface of the light-tunnel through the IR-cut mirror. The IR-cut mirror is set in this unit to eliminate the excessive heat by the lamp energy. This color filter separates the white light into the 3 colors R,G and B. A photo-sensor should be set in this unit to detect the transition timing pproperly between color filters. The maximum rrotating speed is 9000rpm. This unit leads the illumination spot to effective area on DMD. This prism also leads the illumination spot to effective area on DMD and at the same time leads the reflection lights on the DMD to the projection lens. This chip turns on and off in projection to each color component per dot depending on the input source. This lens enlarges and projects the incidend light coming from the DMD. 21 XV-Z9000U/E Adjusting the mirrors Make adjustment by the indication territory on the screen to prevent the circumference of the screen from getting dark because a lighting range deviated. 1. Remove the top body so that the optical unit may be seen. Display white only screen on the screen. 2. Detach the mirror adjustment part cover 1 on the bottom right of the projection lens. 3. Turn three screws with special hexagon wrench (9HPH10XL120) and adjust so that a part of the screen may not get dark because a lighting range deviated. 4. Mount the adjustment part cover 1. 5. Mount the top panel. Insert hexagon wrench in this direction. Expansion figure of part A Adjusting the back focal distance after replacing the projection lens Note: A piece of temporary tape is attached on the focus ring that comes with the replacement projection lens. Keep this tape in place until the finish of the adjustment. (1) Provide a distance of 2.4 m between the set and the screen and adjust the zoom knob to “wide end”. (2) Adjust the lens shift until the projection lens comes to the same level as the center of the screen. (3) Detach the optical unit top cover A from behind the projection lens. (4) Loosen the four hex screws B in the back of the projection lens. (5) Insert the adjustment screwdriver C (9EVDRIVERZ9000) in the hole D at the back of the lens. Put the center of the screen in the best focus. (Preferably feed the SXGA signal for 1-dot white crosshatch pattern or 1-dot white dot pattern on black background.) (6) Tighten the four hex screws B to the torque of 0.3 Nm (3.06 kgfcm), and apply screw loctite to them. (7) Peel the temporary tape off the focus ring of the projection lens. (8) Attach the optical unit top cover A back into position. Finally fix the two screws E and apply screw loctite to them. 22 XV-Z9000U/E When the DMD unit has been replaced Note: DMD chip and Formatter PWB are supplied at the same time, and an exchange only with DMD isn't done.Refer to "REMOVING OF MAJOR PARTS" when exchanging Formatter PWB. There is no need to readjust the back focal distance of the projection lens. If focusing is noticeably poor, however, make this readjustment. (1) (2) (3) (4) (5) (6) (7) Provide a distance of 2.4 m between the set and the screen. Adjust the lens shift until the projection lens comes to the same level as the center of the screen. Detach the optical unit top cover A from behind the projection lens. Loosen the four hex screws B in the back of the projection lens. Adjust the zoom knob at the front of the projection lens to “tele end” and ensure good focusing. Then adjust the zoom knob at the front of the projection lens to “wide end”. Insert the adjustment screwdriver C (9EVDRIVERZ9000) in the hole D at the back of the lens. Put the center of the screen in the best focus. (Preferably feed the SXGA signal for 1-dot white crosshatch pattern or 1-dot white dot pattern on black background.) (8) Move the zoom knob from “wide end” back to “tele end” and see if focusing is ensured. If not, repeat the above steps (5), (6) and (7) until the best focus is achieved. (9) Tighten the four hex screws B to the torque of 0.3 Nm (3.06 kgfcm), and apply screw loctite to them. (10) Attach the optical unit top cover A back into position. Finally fix the two screws E and apply screw loctite to them. E E A C X B B D B B Expansion figure of part X 23 XV-Z9000U/E ELECTRICAL ADJUSTMENT Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. No. Adjusting point Adjusting conditions Adjusting procedure 1 EEPROM initialization 1. Turn on the power (with the lamp on) and warm up the set for 15 minutes. 1. Make the following settings. Press SW2002 to enter the process mode. Execute the S2 and S4 commands on the SSS menu. With the S2 command, all the circuit boards than the PC board will be initialized. Do not activate the S1 command because otherwise the PC board itself will be initialized. (The delivered PC board has been factory-adjusted.) If by any chance the PC board must be readjusted, follow the instructions in "Adjusting the PC Board" on page 28. 2 RGB drive adjustment (on the PC board) 1. Feed the 100% and 0% signals for each of the red, green and blue colors. INPUT5 2. Select the following group and subject. Group: A/D Subject: R-D (R) G-D (G) B-D (B) 1. Using the control switches on the set or the buttons on the remote control, adjust the setting until bit dropouts start at the white level. 3 DLP voltage adjustment (reference) 1. Keep out any signal input. 2. Select the following group and subject. Group: DLP Subject: VOLTAGE 1. Select the setting of the rank marked on the formatter PWB, referring to the menu. 2. Make this adjustment when the DLP chip has been replaced or when the combination of DLP chip and formatter PWB has been changed. 3. Rank B C D E Setting 1 2 3 4 4 Color wheel index adjustment 1. Feed the color wheel index adjustment pattern signal. INPUT5 2. Select the following group and subject. Group: DLP Subject: CW INDEX 1. Adjust the setting so that the R, G and B lamp tone pattern should be smooth without noises. R G B 24 XV-Z9000U/E No. Adjusting point Adjusting conditions Adjusting procedure 5 RGB tone reproduction adjustment 1. Feed the SMPTE pattern signal. INPUT5 2. Select the following group and subject. Group: DLP Subject: R-BRIGHT G-BRIGHT B-BRIGHT 1. Make sure the 100% and 95% white and the 0% and 5% black tones are visible. 2. If the black tone appears otherwise, finely adjust the R-BRIGHT, G-BRIGHT and B-BRIGHT settings. 6 Adjusting the Background Color 1. Select the following group and subject. Group: DLP Subject: R-GAIN G-GAIN B-GAIN 2. Feed the Component video, 75% white signal. 3. Signal level: 0.7±0.05 Vp-p (sync section not included) 4. R-GAIN, G-GAIN and BGAIN initial settings: 95 5. Target chromaticity: x = 0.272 ± 0.005 y = 0.310 ± 0.005 (color temperature 9500K+15 µV) 1. Project an image over a 40-inch screen and measure the chromaticity at the center using a chromaticity meter. 2. Keep the G-GAIN setting fixed at 95. 3. Adjust the B-GAIN setting to get the y value to its target chromaticity. 4. Adjust the R-GAIN setting to get the x value to its target chromaticity. 7 Video horizontal center adjustment 1. Feed the NTSC monoscope pattern signal. INPUT4 2. Select the following group and subject. Group: VIDEO 1 Subject: NTSC-H 1. Using the control switches on the set or the buttons on the remote control, adjust the setting until the overscan should be equal at right and left. 8 Video BRIGHTNESS adjustment 1. Feed the NTSC 10-step gray-scale signal. 2. Select the following group and subject. Group: VIDEO1 Subject: BRIGHT 1. Using the control switches on the set or the buttons on the remote control, adjust the setting until more bit dropouts start at the 0% black level. 9 Video picture adjustment 1. Feed the NTSC 10-step gray-scale signal. 2. Select the following group and subject. Group: VIDEO1 Subject: PICTURE 1. Using the control switches on the set or the buttons on the remote control, adjust the setting until bit dropouts start at the 100% white level. 10 Video tint adjustment 1. Feed the internal 8CH (split color bar) signal. INPUT4 2. Select the following group and subject. Group: VIDEO1 Subject: TINT 1. Check the fixed setting. Fixed setting: 128 25 XV-Z9000U/E No. Adjusting point Adjusting conditions Adjusting procedure 11 NTSC color saturation adjustment 1. Feed the internal 8CH (split color bar) signal. INPUT4 2. Select the following group and subject. Group: VIDEO1 Subject: N-COLOR 1. Check the fixed setting. Fixed setting: 105 12 PAL color saturation adjustment 1. Feed the PAL color bar signal. INPUT4 2. Select the following group and subject. Group: VIDEO1 Subject: P-COLOR 1. Check the fixed setting. Fixed setting: 110 13 SECAM color saturation adjustment 1. Feed the SECAM color bar signal. INPUT4 2. Select the following group and subject. Group: VIDEO1 Subject: S-COLOR 1. Check the fixed setting. Fixed setting: 110 14 DTV BRIGHTNESS adjustment (Take this procedure for Model XVZ9000U only.) 1. Feed the 100% color bar signal (component signal) or the 10-step gray scale signal to the input terminal 480I. INPUT2 2. Select the following group and subject. Group: DVD Subject: BRIGHT 1. Using the control switches on the set or the buttons on the remote control, adjust the setting until more bit dropouts start at the 0% black level. 15 DTV CONTRAST adjustment (Take this procedure for Model XVZ9000U only.) 1. Feed the 100% color bar signal (component signal) or the 10-step gray scale signal to the input terminal 480I. INPUT2 2. Select the following group and subject. Group: DVD Subject: CONTRAST 1. Using the control switches on the set or the buttons on the remote control, adjust the setting until bit dropouts start at the 100% white level. 16 DVD color saturation adjustment DVD tint adjustment 1. Feed the 100% color bar signal (480I component signal) to the Y, Pb and Pr input terminals. INPUT2 2. Select the following group and subject. Group: DVD Subject: COLOR TINT 1. Check the fixed settings. Fixed setting: TINT at 32 COLOR at 36 26 XV-Z9000U/E No. Adjusting point Adjusting conditions Adjusting procedure 17 White balance checking and readjustment 1. Take the adjustment conditions discussed for Item 11. Make sure there is no white balance difference between the set and the standard monitor. 18 Color-related performance checking 1. Feed the color bar signal. 1. Select L1 from the process mode LINE. Check the Color and Tint performance. 19 Video-related performance checking 1. Feed the monoscope pattern signal. 1. Select L2 from the process mode LINE. Check the Picture, Brightness and Sharpness performance. 20 RGB-related performance checking 1. Feed the RGB signal. 1. Select L4 from the process mode LINE. Check the Picture, Brightness, Red, Blue, Clock, Phase, H-Position and V-Position performance. 21 Off-timer performance 22 Thermistor performance checking 1. Heat the thermistor with a hair dryer. 1. Make sure that the temperature is indicated. 23 Auto sync performance checking 1. Feed the phase check pattern signal. 1. In the VGA, SVG Aand XGAmodes, make sure the Clock, Phase, H-Pos and V-Pos settings can be automatically adjusted. 24 Delivery settings 1. Select OFF from the process mode LINE. Make sure the off-timer starts with 5 minutes onscreen and the set turns itself off in 5 minutes. 1. Make the following settings. Destination 27 Adjustment process Remote control setting XV-Z9000U S4 Factory setting 4 XV-Z9000E S3 Factory setting 3 XV-Z9000U/E Adjusting the PC Board 1. Initializing the EEPROM 1) Press SW2002 to enter the process mode. 2) Execute the S1 command on the SSS menu. (The S1 command initializes the PC board alone. Do not execute the S2 command because otherwise the adjustment data other than the PC board will be initialized.) 3) Make sure that the program version VER.XXX on the SPECIAL menu is the latest one. 2. Adjusting the levels 2.1 Setting the oscilloscope Set the oscilloscope range to DC 1V/div. and 5 µsec/div. 2.2 Connecting the PC interface 1) Connect the specified cable between the analog output jack (signal generator) and the DUSB connector (INPUT5 of the projector). Set the projector’s input selector to INPUT5. 2) Set the signal generator to the XGA mode (1024x768, 60 Hz, 32 tones). Adjust the output amplitude to 700 mVp-p between the black and white levels (terminated with a 75-ohm impedance). 3) Turn on the power. 2.3 Adjusting and checking the levels 1) Press SW2002 to enter the process mode. 2) Adjust the R-BRIGHT setting of Group A/D until bit dropouts start at the black level of the red signal. 3) Adjust the B-BRIGHT setting of Group A/D until bit dropouts start at the black level of the blue signal. 4) Adjust the G-BRIGHT setting of Group A/D until bit dropouts start at the black level of the green signal. 2.4 Adjusting the DTV 1) Feed the signal to the INPUT2’s RCA input terminal. 2) Set the signal generator to the 1080i 60-Hz mode with white signal. Adjust the output amplitude to 700 mVpp between the black and white levels. 3) Connect the specified cable between the analog output (signal generator) and the RCA connector (INPUT2 of the projector). 4) Make the G-BRIGHT setting the same as the G-BRIGHT setting of Group A/D. 5) Adjust the CB-OFFSET setting of Group DTV to 20. 6) Adjust the CR-OFFSET setting of Group DTV to 20. 7) When the CB-OFFSET and CR-OFFSET settings have been made, add 5 points to the G-BRIGHT setting for Model XV-Z9000U and 4 points for Model XV-Z9000E. 8) Finally press SW2002 to exit from the process mode. 28 XV-Z9000U/E Process menu 1 Group Sub Group Subject Adjust PC Image A/D R-BRIGHT G-BRIGHT B-BRIGHT R-D B-D G-D Adjust HDDE formatter DLP VOLTAGE CW-INDEX R-BRIGHT G-BRIGHT B-BRIGHT R-GAIN G-GAIN B-GAIN Adjust Component DTV (High Definition) G-BRIGHT CB-OFFSET CR-OFFSET Adjust VIDEO Image VIDEO1 NTSC-H PICTURE BRIGHT TINT N-COLOR P-COLOR S-COLOR SET UP SET UP B SET UP C VIDEO2 PEAK FIL PEAK GAIN PEAK COR N358 DLY N433 DLY PAL DLY SECAM DLY Adjust Component (480i) DVD CONTRAST BRIGHT TINT COLOR 29 XV-Z9000U/E Process menu 2 Group Sub Group Subject Process mode LINE L1 L2 L3 L4 OFF TEMP OFF SENSOR CHECK INITIAL SETTING SSS TIME S1 S2 S3 S4 S5 LAMP Sample Pattern PATTERN RGB RGB(50) CROSS STEP COLOR CHR Adjust CVIC CVIC MODDE -PROGRESSIVE IP FILM PTG MSW LSW C-LEVEL C-LIMIT C-LPF C-THRESH C-MISSTH C-MOVIEA C-MOVIEB C-MOVIEC 30 XV-Z9000U/E Process menu 3 Group Sub Group Subject Adjust CVIC CVIC BBN-TBL0 -ENHANCE-VIDEO BBN-TBL1 DFC-TBL0 DFC-DIR0 DFC-EDG0 DFCTBL1 DFC-DIR1 DFC-EDG1 CVIC BBN-TBL0 -ENHANCE-HDTV BBN-TBL1 DFC-TBL DFC-DIR DFC-EDG CVIC BBN-GAIN0 -ENHANCE-RGB BBN-GAIN1 BBN-GAIN2 BBN-TBL DFC-TBL DFC-DIR DFC-EDG CVIC CUBIC-RGB -SCREEN CUBIC-VIDEO CVIC XEGTH -IDC XLTH1-H XLTH1-L XLTH2-H XLTH2-L VEGTH VLTH1-H VLTH1-L VLTH2-H VLTH2-L Version Check etc. (High Definition) Special IPL E2PROM ADR RD/RW 31 XV-Z9000U/E TROUBLE SHOOTING TABLE Checking the basic performance Is the POWER LED on or flickering in red or blue? NO Go to "Checking the power unit" YES Is the set turned on by the set's or remote controller's power key? NO Go to "Checking the microcomputer peripherals" and "Checking the PC PWB". YES Is the cooling fan running? Is the lamp on? NO Go to "Checking the lamp light-up". YES NO Is the user menu displayed? Check the formatter circuit’s peripheral circuits. YES Is the video input as specified? NO YES Is the component input as specified? Check the IC2505 circuit and its peripheral circuits. Are there output signals at every other pin from pins (41) to (60) of P3580? NO Check the IC2505 circuit and its peripheral circuits. Are there output signals at every other pin from pins (41) to (60) of P3580? NO Check the IC2505 circuit and its peripheral circuits. Are there output signals at pins (32), (34) and (37) of P3580? NO Check the IC2005 circuit and its peripheral circuits. NO YES Does the RS-232C interface function? NO NO YES If the RGB input as specified? Are there output signals at pins (32), (34) and (37) of P3580? Check the PC board circuit’s peripheral circuits. NO YES Recommended NO communication software: “TERA TERM” Make the following settings: baud rate at 9600 bps, bit length at 8 bits, stop bit at 1 bit and no parity. Press the RETURN key on the keyboard. Does “ERR” show up again? YES END 32 XV-Z9000U/E Checking the power unit Are all the connectors NO inside the power unit tightly connected? Insert the connectors CN7105, 7103, 7101AND 7102 tightly. YES Is the lamp cover closed completely? NO Tighten up the lamp door closed with the screws. YES Is the bimetal switch off? NO Replace the bimetal switch or press the red button to reset. YES Is AC voltage applied across the RL7001 relay? NO YES Is AC voltage applied across L7005? Replace F7001. NO Replace F7002. YES Is there DC voltage of about 6 V across C7151? NO Check the peripheral circuits of Q7101~Q7107. Replace any of them as required. YES Is there DC voltage of about 340 V across CN7003? NO Check the circuits leading to the primary side of T7002 for damage. Replace any of them as required. YES Are there the specified voltages at the output terminals of CN7101 and CN7102? NO Check the circuits leading to the secondary side of T7002 for damage. Replace any of them as required. YES Check the output PWB circuits. 33 XV-Z9000U/E Checking the PC PWB 0 Is the user menu properly displayed? YES NO Check the on-screen display. Check the DTV RGB input. Check the DTV component input. Check the VIDEO input. Check the basic signal flow. The signal flow from CVIC_IC to the panel output is the same for the component and video signals. Therefore the lines after CVIC are not checked. (The 480i and 580i component signals are not included.) The signal flows through the same circuits as the DTV RGB signal does. Check the SOG (Sync On Green) circuit and the color adjustment circuit. (The 480i and 580i component signals are not included.) The video signal flows through a different route from the RGB input signal, and goes into CVIC_IC. Therefore check the video signal ICs. Check the D-SUB input. Check the D-SUB input. End 34 XV-Z9000U/E Checking the RGB input Feed the sync-separated DTV RGB signal to INPUT1 or INPUT2. (The 480i and 580i component signals are not included.) 1 Using the front-panel key or the remote control, select INPUT1 or INPUT2. 2 Does the image appear? NO Check to see if the video input is as specified. YES Is the image disturbed? NO Go to "Checking the sync signal". YES 3 Do R, G and B colors appear? NO Go to "Checking the RGB signal". YES Is the contour as specified? NO YES IC8004 or its peripheral circuit defective. End 35 XV-Z9000U/E Checking the video input Make sure the input signal setting is as specified. YES Is there the video signal at the land of C8077? NO Input PWB defective. YES Check the sync signal. YES IC8025 or IC8004 defective. Checking the input signal setting Is the input signal setting as specified? NO Select the specified signal. YES 2 Is the connector properly connected? NO Reconnect the connector. YES End 1 36 XV-Z9000U/E Checking the sync signal Is there vertical sync signal at TL8134? NO YES Is there horizontal sync signal at TL8133? NO Check the input signal setting. YES Input PWB defective. Is there vertical sync signal at TL8131? NO YES Is there horizontal sync signal at TL8130? NO IC8302, IC8325, IC8299 or their peripheral circuits defective. YES Are both the vertical and horizontal sync signals timely? NO There is no problem with the sync signal. End. YES Is the signal generator (input source) as specified? NO Make the specified signal source settings. YES Input PWB defective. 2 37 XV-Z9000U/E Checking the RGB signal Is the type of signal set at RGB? YES NO Set to the RGB signal. Call the process mode. Select R, G and B separately on the pattern menu. Go to “Checking the GA4 peripheral circuits”. Set the signal generator to the gradation signal mode in order to check the input signal. Measure the gradation signals at TL8073, T8074, T8075 and T8080. Are there specified signals at TL8073, TL8074, TL8075 and TL8080? YES IC8025 or its peripheral circuit defective. NO Are there input signals at C8069 and C8061? YES IC8004 or its peripheral circuit defective. 38 NO Input PWB defective. XV-Z9000U/E Checking the GA4 peripheral circuits Call the process mode, and select R, G and B separately on the pattern menu. Are there specified R, G and B video output signals? YES End of checking the GA4 peripheral circuits. NO Are the measured signals the same as the signals selected on the pattern menu? NO Is there clock signal at R974? YES Output PWB defective. NO Is there clock signal (37.125 MHz) at TL8114? YES YES IC8029 defective. NO Is there clock signal (37.125 MHz) at FL8110? NO X8005 defective. YES IC8025 defective. Are there sync signals at TL8026, TL8027 and TL8028? NO Are there sync signals at TL8112 and TL8133? YES YES Using the oscilloscope, measure the signals at TL8141 thru TL8148. Are the measured signals the same as the signals selected on the pattern menu? IC8029 defective. NO Digital panel PWB defective. YES Using the oscilloscope, measure the signals at TL8106 thru TL8111. Are the measured signals the same as the signals selected on the pattern menu? NO IC8025 defective. YES IC8029 defective. 39 NO IC8025 defective. XV-Z9000U/E Checking the component inputs (Except for 480I) Feed the component signal to INPUT1 or INPUT2. Using the front panel key or the remote control, select INPUT1 or INPUT2. Does an image appear on the NO screen? Go to "Checking the SOG circuit". YES 4 Are the colors as specified? YES NO Is the type of signal set at COMPONENT? YES NO Set the type of signal to COMPONENT. Carry out the process adjustment. NO 4 Is the image contour as specified? YES IC8004 or IC8025 defective. NO End of checking the component input. 40 XV-Z9000U/E Checking the SOG circuit Measure the signal at TL8136 on the oscilloscope. Is the composite sync signal played back timely? YES NO There is no problem with the SOG circuit. End. Measure the land of C8069 on the oscilloscope. Is there the Y signal including the sync signal? NO Go to “Checking the input signal settings”. YES SOG sync separation circuit defective. Input PWB defective. Checking the on-screen display. Is the on-screen display color as specified? YES NO Carry out the output line adjustment in the adjustment process. Go to “Checking the GA4 peripheral circuits”. 0 Get the flash ROM reprogrammed. 41 XV-Z9000U/E Checking the video input Feed the composite video signal to INPUT4. Using the front panel key or the remote control, select INPUT4. Select VIDEO as the type of signal on the user menu. 5 Does the image appear? NO YES Is the image disturbed? NO Go to "Checking the video sync signal". YES NO NO Is the contour as specified? Go to "Checking the video sync signal". Carry out the process adjustment. YES There is no problem with the video input. End. 5 Is there the video signal at pin (72) of IC8338? Is the video signal as specified? NO YES IC8338 defective. 6 42 XV-Z9000U/E 6 Measure the VPC (IC8338) clock signal at TL8004. Is the clock signal as specified? NO YES IC8338 defective. Go to “Checking the video sync signal”. IC8025 or its peripheral circuit defective. Checking the video sync signal Using the oscilloscope, measure the signal at TL8140. (Check the vertical sync signal.) Is the vertical sync signal as specified? NO YES Using the oscilloscope, measure the signal at TL8142. (Check the horizontal sync signal.) Is the horizontal sync signal as specified? NO Go to "Checking the input signal setting". YES 7 Input PWB defective. 43 XV-Z9000U/E Checking the DSUB input. Feed the PC-RGB signal to INPUT5. Select INPUT5 as the input. NO Does the image appear? Check to see if there are the R, G and B signals at pins (126), (136) and (146) of IC8004. YES Is there any distortion with the image? YES NO Are there the R, G and B signals? NO YES 3 Check the vertical and horizontal sync signals at pin (6) of IC8364 and pin (6) of IC8385. Are the sync signals as specified? NO Sync separation circuit, IC8354m IC8365 or their peripheral circuit defective. NO IC8302 or its peripheral circuit defective. YES Are there the horizontal and vertical sync signals at TL8130 and TL8131? YES IC8025, IC8004 or their peripheral circuit defective. 44 DSUB connector or its peripheral part defective. XV-Z9000U/E Checking the lamp light-up The lamp fails to light up. Is discharge sound heard when turning on the power switch? YES Is the lamp or CW line socket out of position? YES NO Replace the lamp or the CW. Are the cooling fans running well? NO Check the power circuit or the fan circuit on the main circuit. YES Is a voltage of about DC 340 V applied across the ballast power circuit CP1001? YES Is a voltage of over 3.5 V applied at pin (1) of the ballast power circuit CP1501? YES NO Check the power circuit. NO Replace the ballast power PWB. Check the microprocessor circuit. Check the microprocessor circuit. Replace the ballast power PWB. 45 NO Reconnect the sockets tightly. XV-Z9000U/E No horizontal synchronization Is the terminal input connection as specified? Is YES the cable tightly connected? NO Is there the horizontal sync pulse at pin (14) of IC2506? NO Check the line between IC2506 and the input terminal. YES Is there the horizontal sync pulse at pin (11) of IC2509? Use the specified cable. Reconnect it tight enough. NO Check the line between IC2506 and IC2509. YES Go to "PC Board Troubleshooting". No vertical synchronization Is the terminal input connection as specified? Is YES the cable tightly connected? NO Is there the vertical sync pulse at pin (14) of IC2501? NO Check the line between IC2501 and the input terminal. YES Is there the vertical sync pulse at pin (8) of IC2509? YES Use the specified cable. Reconnect it tight enough. NO Check the line between IC2506 and IC2509. Go to "PC Board Troubleshooting". 46 XV-Z9000U/E Checking IC3504 (3D Noise Reduction) and its Peripheral Circuits Are there the input signals at pins (88) (Y signal) and (96) (C signal) of IC3504? NO Check the signal input circuit or IC2505 and its peripheral circuits. YES Are there the output signals at pins (84) (Y signal) and (83) (C signal) of IC3504? YES NO Check IC3504 and its peripheral circuits. Check the line up to the PC board connector or the circuits that follow the PC board. 47 XV-Z9000U/E Checking the Component and RGB Inputs Are there signals at pins (34), (36) and (38) of IC2505? NO Check the signal input circuit or IC2505 and its peripheral circuits. YES NO There are no RGB colors. YES Are there signals at pins (3), (5) and (6) of IC2507? Check the circuit of the color that fails to appear. NO Check the line between Q2509 and Q2517 and its peripheral circuits, or IC2507. YES NO There are no RGB colors. YES Are there signals at pins (56/26), (58/28) and (60/30) on the board-toboard section of P3580? NO Check the line between Q2518 and Q2520 and its peripheral circuits. YES Are there signals at pins (49/19), (51/21) and (53/23) on the board-toboard section of P3580? YES Check the circuit of the color that fails to appear. NO Check the line from Q2525 through Q2523 to Q2524 and its peripheral circuits. Check the board-to-board connections or the circuits that follow the PC board. 48 XV-Z9000U/E Technische Daten Produkttyp Projector Modell XV-Z9000E Videosystem PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43 DTV 480i/480P/720P/1080i Display-Verfahren Single Panel Digital Micromirror Device (DMD™) von Texas Instruments, RGB optisches Verschlussverfahren DMD-Feld Feldformat: 0,8" Antriebsverfahren: Digital Light Processing (DLP™) von Texas Instruments Anzahl der Punkte: 921.600 Punkte (1.280 [H] × 720 [V]) Linse 1 –1,35 Zoom-Linse, F3,0,f=32,5 –44,0 mm Projektionslampe 250 W NSH-Lampe Videoeingangssignal RCA-Stecker: VIDEO (INPUT 4), Gemischtes Video, 1,0 Vp-p, negatives Sync.-Signal, 75 Ω terminiert S-Videoeingangssignal 4-Pin Mini DIN-Stecker (INPUT 3) Y (Luminanz-Signal): 1,0 Vp-p, negatives Sync.-Signal, 75Ω terminiert C (Chrominanz-Signal): Stoß 0,286 Vp-p, 75Ω terminiert Komponenten- RCA-Stecker (INPUT 1, 2) Eingangssignal Y: 1,0 Vp-p, negatives Sync.-Signal, 75Ω terminiert CB: 0,7 Vp-p, 75Ω terminiert CR: 0,7 Vp-p, 75Ω terminiert 520 TV-Zeilen (NTSC 3,58 Eingang), 750 TV-Zeilen (DTV 720P Eingang) Horizontal-Auflösung 15-PIN MINI D-SUB STECKANSCHLUSS (INPUT 5): RGB getrennt/gemischte Sync./Sync. auf Grün-Typ analoger Eingang: 0–0,7 Vp-p, RGB-Eingangssignal positiv, 75Ω terminiert HORIZONTALES SYNC.-SIGNAL: TTL-Pegelsignal (positiv/negativ) oder gemischtes Sync.-Signal (nur Macintosh) VERTIKALES SYNC.-SIGNAL: Wie oben 12–120 MHz Punkatetakt 43–100 Hz Vertikale Frequenz 15–81 kHz Horizontale Frequenz 9-Pin D-Sub-Steckanschluß (RS-232C-Eingangs-Port) Computersteuerungs-Signal 100–240 V Wechselstromspannung Nennspannung 3,6 A Eingangsspannung 50/60 Hz Nennfrequenz 345 W (Wenn in “Kinofilm-Modus” “HELLIGK.” angewählt ist) Stromaufnahme 310 W (Wenn in “Kinofilm-Modus” “NORMAL” angewählt ist) 1.400 BTU/Stunde Stromverlust +5°C bis +35°C Betriebstemperatur -20°C bis +60°C Lagertemperatur Kunststoff Gehäuse 38 kHz I/R-Trägerfrequenz 475 × 178 × 406 mm (B × H × T) (nur Hauptgerät) Abmessungen (ca.) 475 × 178 × 496 mm (B × H × T) (einschließlich Buchsenabdeckung) 9,5 kg (nur Hauptgerät) Gewicht (ca.) Fernbedienung, Zwei AA-Batterien, Netzkabel (1,8 m), 21-Pin RCA-Konversionsadapter, Mitgeliefertes Zubehör Video-Kabel, RGB-Kabel, Buchsenabdeckung, Linsenkappe (aufgesetzt), CD-ROM, Zwei Projektor-Bedienungsanleitungen, SharpVision Manager-Bedienungshandbuch Lampeneinheit (Lampe/Gehäusemodul) (BQC-XVZ9000/1), Fernbedienung Ersatzteile (RRMCG1657CESA), AA-Batterien, Netzkabel (QACCV4002CEZZ, QACCB5024CENA), 21-Pin RCA-Konversionsadapter (QSOCZ0361CEZZ), Video-Kabel (QCNWGA001WJZZ), COMPUTER-RGB-Kabel (QCNW-5050CEZZ), Buchsenabdeckung (GCOVA1985CEKA), Linsenkappe (PCAPH1056CESA), CD-ROM (UDSKA0047CEN1), Zwei ProjektorBedienungsanleitungen(TINS-7521CEZZ, TINS-7522CEZZ), SharpVision ManagerBedienungshandbuch(TINS-7523CEZZ) Dieser SHARP-Projektor verwendet einen DMD-Chip. Dieser hochentwickelte Chip beinhaltet 921.600 Pixel. Wie bei allen hochtechnologischen Elektronikgeräten wie großen Fernsehbildschirmen, Videosystemen und Videokameras, gibt es auch hier bestimmte akzeptable Toleranzen, denen das Gerät entsprechen muß. Dieses Gerät hat einige inaktive Pixel innerhalb akzeptabler Toleranzen, die in inaktiven Punkten auf dem Bildschirm resultieren. Dies hat keinen Einfluß auf die Bildqualität oder die Lebensdauerdes Gerätes. Änderungen der technischen Daten ohne vorherige Ankündigung vorbehalten. 49 XV-Z9000U/E HINWEIS FÜR DAS WARTUNGSPERSONAL 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Auswechseln der Lampe ACHTUNG: UV-STRAHLUNG 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Hinweis: Da die Lampe während des Betriebs sehr heiß wird, sollte die Lampe erst ausgewechselt werden, nachdem das Gerät mindestens eine Stunde ausgeschaltet war, damit die Lampe ausreichend abkühlen kann. Beim Installieren der neuen Lampe muß darauf geachtet werden, die Lampe selbst (Glaskolben) nicht zu berühren. Vielmehr muß die Lampe am Reflektor 2 gehalten werden. [Es darf nur ein Original-Ersatzteil verwendet werden.] Die Beleuchtungsquelle des LCD-Projektors, eine UHP-Lampe, emittiert eine geringe Menge UV-Strahlung. DIREKTE BESTRAHLUNG AUF AUGEN UND HAUT MUSS VERMIEDEN WERDEN. Zur Gewährleistung der Sicherheit muß folgendes beachtet werden: 1 Lampe 1. Bei Arbeiten am Projektor bei eingeschalteter Lampe und abgenommenem oberen Gehäuse muß unbedingt eine Sonnenbrille getragen werden. 2 Reflektor GEFAHR! — Niemals die Spannungsversorgung einschalten, ohne daß eine Lampe vorhanden ist, um elektrische Schläge und Schäden am Gerät zu vermeiden, da der Stabilisator anfangs hohe Spannungen erzeugt. 2. Die Lampe darf nicht außerhalb des Lampengehäuses eingeschaltet werden. Da eine geringe Menge UV-Strahlung an der Öffnung zwischen den Lüftern austritt, wird empfohlen, während der Wartungsarbeiten die Abdeckkappe des Zusatzobjektivs an dieser Öffnung anzubringen, um Augen und Haut vor den UV-Strahlen zu schützen. 3. Betrieb für länger als 2 Stunden bei abgenommenem Gehäuse ist nicht zulässig. Zur Beachtung bei UV-Strahlung und Mitteldruck-Lampen 1. Vor dem Auswechseln der Lampe muß der Netzstecker gezogen werden. 2. Vor Durchführung von Wartungsarbeiten muß das Gerät eine Stunde abkühlen. 3. Die Lampe darf nur gegen eine der gleichen Art ausgewechselt werden. Typ BQC-XVZ9000/1, bemessen für 355 V/250 W. 4. Die Lampe gibt eine geringe UV-Strahlung ab, daher muß direkter Augenkontakt vermieden werden. 5. Die Mitteldruck-Lampe weist ein Explosionsrisiko auf. Daher müssen die nachstehenden Installationsanweisungen beachtet werden, und die Lampe muß vorsichtig behandelt werden. 50 XV-Z9000U/E Lage der Bedienelemente Projektor Ansicht von vorne und oben Linsenversteller Temperaturwarnanzeige (TEMPERATURE WARNING) Zoom-Knopf Lampenaustausch-Anzeige (LAMP REPLACEMENT) Fokusring Netzanzeige (POWER) Einsteller Einlass-Lüftungsöffnung Einsteller Fernbedienungssensor Linsenkappe Menü-Taste (MENU) Skalierungstaste (RESIZE) Einstelltasten (ADJUSTMENT) ('/"/\/|) Eingangstaste (INPUT) Netztasten (POWER) Ein/Aus (ON/OFF) Eingabetaste (ENTER) Rückgängig-Taste (UNDO) Seiten- und Rückansicht 51 XV-Z9000U/E Projektor Seiten- und Rückansicht Einlass-Lüftungsöffnung Einlass-Lüftungsöffnung Auslass-Lüftungsöffnung Fernbedienungssensor Eingang 5 Computer-RGB-Port (INPUT 5 COMPUTER-RGB) (15poliger Mini-D-Sub) S-Video-Eingang 3-Buchse (S-VIDEO INPUT 3) (4poliger Mini DIN) Eingang 1 Komponente / RGB-Buchsen (INPUT 1 COMPONENT / RGB) (RCA) Wechselstrom-Buchse Eingang 2 Komponenten / RGB-Buchsen (INPUT 2 COMPONENT / RGB) (RCA) Video-Eingang 4-Buchsen (VIDEO INPUT) (RCA) 52 RS-232C-Port(9poliger D-Sub) 12 V Gleichstrom-Ausgang (DC 12V OUTPUT) Eingangsbuchse für Drahtfernbedienung 12 V Gleichstrom 200 mAAusgangsbuchse (OUTPUT) XV-Z9000U/E Fernbedienung Vorderansicht Netztasten (POWER) Ein/Aus (ON/OFF) Menü-Taste (MENU) Eingabetaste (ENTER) Einstelltasten (ADJUSTMENT) (\/|/'") Rückg ängig-Taste (UNDO) Eingang 1-Taste (INPUT 1) Eingang 3-Taste (INPUT 3) Eingang 2-Taste (INPUT 2) Eingang 5-Taste (INPUT 5) Eingang 4-Taste (INPUT 4) GRÖSSE ÄNDERN-Taste (RESIZE) Kinofilm-Modus-Taste (THEATER MODE) Farbtemperatur-Tasten (CLR TEMP) GAMMA-Taste Trapeztaste (KEYSTONE) Taste für automatische Synchronisation (AUTO SYNC) Hintergrundbeleuchtungs-Taste (BACKLIGHT) Ansicht von oben Fernbedienungssignal-Sender Eingangsbuchse f ür Drahtfernbedienung Einlegen der Batterien 1 Ziehen Sie die Lasche auf der Batterieabdeckung nach unten und nehmen Sie die Abdeckung in Pfeilrichtung ab. BatterieAbdeckung 2 Legen Sie zwei AABatterien unter Anpassung der im Batteriefach aufgezeigten (+)- und (–)Markierungen ein. Sie die untere 3 Setzen Lasche der Batterieabdeckung in die Öffnung ein und drücken Sie die Abdeckung herunter, bis sie einrastet. BatterieAbdeckung Batteriefach 53 XV-Z9000U/E Mit der Fernbedienung kann der Projektor innerhalb des links aufgeführten Bereiches gesteuert werden. Fernbedienung 7m 45˚ • Für einfachen Betrieb kann das Signal von der Fernbedienung von einem Bildschirmreflektiertwerden. Dennoch variiert die effektive Signalentfernung entsprechend des Bildschirmmaterials. 30˚ 30˚ 45˚ 30˚ Fernbedienung Benutzung der Fernbedienung in einem dunklen Raum Die Hintergrundbeleuchtung der Betriebstasten kann durch Betätigung von BACKLIGHT für 5Sekunden ein- und ausgeschaltet werden. Wenn Sie die eingeschalteten Hintergrundbeleuchtungen ausschalten möchten, drücken Sie noch einmal BACKLIGHT. Hintergrundbeleuchtungs-Taste (BACKLIGHT) Benutzung einer Drahtfernbedienung 3,5 mm StereoMinibuchsenkabel (im Handel erhältich) Wenn die Fernbedienung aufgrund des Bereiches oder der Positionierung des Projektors (Rückprojektion usw.) nicht verwendet werden kann, schließen Sie ein 3,5 mm Stereo-Minibuchsenkabel (im Handel erhältlich) von der DrahtfernbedienungsEingangsbuchse oben auf der Fernbedienung an die sich auf der Rückseite des Projektors befindliche Drahtfernbedienungs-Eingangsbuchse an. 54 XV-Z9000U/E Pin-Belegung INPUT 5 RGB-Signaleingangs-Port: 15-Pin Mini-D-Sub-Buchse 11 6 1 15 10 5 RGB-Eingang Analog 1. Videoeingang (rot) 2. Videoeingang (Grün/Sync. auf Grün) 3. Videoeingang (blau) 4. Nicht angeschlossen 5. Gemischtes Sync.-Signal 6. Erdung (rot) 7. Erdung (Grün/Sync. auf Grün) 8. Erdung (blau) 9. 10. 11. 12. 13. Nicht angeschlossen MASSE MASSE Bi-direktionale Daten Horizontales Sync.Signal 14. Vertikales Sync.-Signal 15. Daten-Zeitgeber RS-232C-Anschlußstelle: 9-Pin D-Sub-Stecker des DIN-D-Sub RS-232C-Kabels 9 5 6 1 Pin Nr. 1 2 3 4 5 6 7 8 9 Signal RD SD SG Name Daten empfangen Daten senden Reserviert Signalerdung Reserviert Reserviert Reserviert 55 E/A Eingang Ausgang Referenz Nicht angeschlossen An internen Schaltkreis angeschlossen An internen Schaltkreis angeschlossen An internen Schaltkreis angeschlossen An internen Schaltkreis angeschlossen An internen Schaltkreis angeschlossen An internen Schaltkreis angeschlossen An internen Schaltkreis angeschlossen Nicht angeschlossen XV-Z9000U/E Abmessungen Ansicht der Rückseite Ansicht von oben Seitenansicht 406 Seitenansicht 178 Seitenansicht Ansicht von vorne 475 Ansicht von unten Einheit:mm 56 XV-Z9000U/E ENTFERNEN DER HAUPTTEILE 1. Ausbau der oberen Abdeckung 2-1. Die beiden Schrauben losdrehen, dann die LEDPlatine entfernen. 2-2. Die Schraube losdrehen und die R/C-Platine entfernen. 2-3. Die drei Schrauben losdrehen und die Betriebsplatine entfernen. 1-1. Die sechs Sicherungsschrauben losdrehen. 1-2. An den seitlichen Pfeil A an der Gehäuseunterseite hineindrücken und die hintere Abdeckung anheben. 1-3. Den Stecker abziehen. 1-4. An den vorderen Pfeil B an der Gehäuseunterseite hineindrücken und die Sperrklinken aushaken. Danach die obere Abdeckung abnehmen. 2-1 R/C Platine 2-2 2-3 LED-Platine Betriebsplatine Obere Abdeckung 1-1 1-3 1-4 1-1 1-4 1-1 1-4 B 1-2 A 1-4 B 1-1 57 XV-Z9000U/E 2. Ausbau des Kühlgebläses und der Platineneinheit 3-1. 3-2. 3-3. 3-4. Die elf Stecker abziehen. Die beiden Schrauben losdrehen und die Lampenfassung entfernen. Die beiden Schrauben losdrehen und das Kühlgebläse entfernen. Die vier Schrauben losdrehen und die Platineneinheit entfernen. 3-1 3-1 (J5) (RC)(TA) (J2) (FD) (FB) (J3) (DB1) 3-4 (FA) 3-4 3-4 3-3 3-2 Platineneinheit LAMPE 3-1 Door SW Bi-Metal Kühlgebläse 58 XV-Z9000U/E 3. Ausbau der Rückwand, der PC-Einheit, des Kühlschachts und der Hauptplatineneinheit 4-1. 4-2. 5-1. 5-2. 6-1. 7-1. 8-1. 8-2. 8-3. Die beiden Schrauben losdrehen. Die drei Schrauben losdrehen und die Abdeckplatte entfernen. Die beiden Schrauben losdrehen. Die vier Sechskanthalterungen entfernen, dann die Abdeckplatte entfernen. Die vier Schrauben losdrehen, dann die PC I/F-Einheit abnehmen. Die vier Schrauben losdrehen, dann den Kühlschacht abnehmen. Die beiden Sechskanthalterungen entfernen. Die fünf Schrauben losdrehen und die Hauptplatine entfernen. Die Halterung entsperren. 6-1 6-1 PC I/F-Einheit (TB) (EA) (FC) 8-2 8-1 Hauptplatine (EB) (CA) 8-2 7-1 Abdeckplatte Kühlschacht 5-2 Rückwand 5-1 5-2 4-1 4-2 8-3 7-1 59 XV-Z9000U/E 4. Entfernen der Netzteilabdeckung, der Netz-/Vorschaltgeräte-Einheit sowie des Netzteils. 9. Die sieben Schrauben losdrehen und die Netzteilabdeckung entfernen. 10-1. Die beiden Schrauben losdrehen. 10-2. Die vier weißen Halter entfernen, dann das Netzteil abnehmen. 11. Die vier Schrauben losdrehen, dann das Netzteil entfernen. 10-1 Netzteilabdeckung Vorschaltgerät 9 11 11 Netzteil 10-2 10-2 9 60 XV-Z9000U/E 5. Ausbau der Optikmechanismus-Einheit und der R/C-Platineneinheit 12. 13. Die sechs Schrauben losdrehen und die Optikmechanismus-Einheit entfernen. Die Schraube losdrehen und die R/C-Platineneinheit entfernen. 12 12 Optikmechanismus-Einheit 12 13 R/C-Platineneinheit 61 XV-Z9000U/E 6. Ausbau von Lampeneinheit, Farbeinstellscheiben-Gebläse, Auslaßgebläse, Luftkanal, Abschirmblech und Bildformatiererplatine 14. Die drei Schrauben losdrehen und die Lampeneinheit entfernen. 15. Die beiden Schrauben losdrehen und das Farbeinstellscheiben-Gebläse entfernen. 16. Die drei Schrauben losdrehen und das Auslaßgebläse entfernen. 17-1. Die beiden Schrauben losdrehen und das Bimetall entfernen. 17-2. Die beiden Schrauben losdrehen und den Luftkanal entfernen. 18-1. Die sechs Schrauben losdrehen und das Abschirmblech (B) entfernen. 18-2. Die drei Schrauben losdrehen und die Bildformatiererplatine entfernen. 18-3. Die drei Schrauben losdrehen und das Abschirmblech (A) entfernen. Abschirmblech (A) Bildformatiererplatine 18-3 Abschirmblech (B) 18-2 18-2 18-1 17-2 15 Luftkanal 17-1 Bimetall 14 16 Auslaßgebläse Lampeneinheit 62 XV-Z9000U/E Rückstellen des Lampenbetriebszeit-Timers ● Rückstellen des Lampenbetriebszeit-Timers Nach dem Auswechseln der Lampe muß der Lampenbetriebszeit-Timer entsprechend den nachfolgenden Anweisungen zurückgestellt werden. 1 Stecken Sie das Netzkabel ein. Sie am Projektor 2 Drücken POWER ON um den LampenBetriebsstundenzähler zurückzusetzen. Drücken Sie POWER ON, während Sie ENTER, und gedrückt halten. ● Lichtquelle(lampe) Die Lampe dieses Projektors kann abhängig von der Betriebsumgebung für etwa 2.000 Stunden verwendet werden. (Wenn die Betriebsumgebung große Unterschiede aufweist, kann die Verwendungdauer der Lampe weniger als 2.000 Stunden betragen.) Es wird empfohlen, die Lampe nach ca. 1.900 Stunden Verwendung auszutauschen, oder wenn eine deutlichere Verschlechterung der Bild- und Farbqualität festgestellt wird. Die Verwendungszeit der Lampe kann mit der Anzeige auf der Bildwand überprüft werden. Wartungsanzeige Temperaturwarnanzeige LampenaustauschAnzeige Symptom Die Temperatur im Gerät ist zu hoch. Abhilfe Problem • Belüftungsöffnungen blockiert. • Den Projektor an einem besser belüfteten Ort aufstellen. • Luftfilter verstopft. • Den Filter auswechseln. • Kühlventilator beschädigt. • Interne Schaltkreise beschädigt. • Den Projektor einem von Sharp autorisierten Händler für Projektoren oder dem Kundendienst zur Reparatur übergeben. • Die Lampe vorsichtig austauschen. Die Lampe leuchtet • Ausgebrannte Lampe. • Den Projektor einem von Sharp • Lampen-Schaltkreis nicht auf. autorisierten Händler für Projektoren oder beschädigt. dem Kundendienst zur Reparatur Die Lampe muß übergeben. ausgewechselt werden. • Die Lampe wurde über 1.900 Stunden verwendet. Symptom Problem Die Lampenaustausch-Anzeige • Die Lampe wurde über 1.900 Stunden leuchtet rot auf und „LAMP.“ und „ “ verwendet. blinken gelb in der unteren linken Ecke der Bildwand. Eine sichtbare Verschlechterung der Bild- und Farbqualität tritt auf. Das Gerät wird automatisch ausgeschaltet und der Projektor auf Betriebsbereitschaft geschaltet. „LAMP.“ und „ “ blinken rot in der unteren linken Ecke der Bildwand und das Gerät wird automatisch ausgeschaltet. • Die Lampe wurde über 2.000 Stunden verwendet. 63 Abhilfe • Einen Austauschlampen-Satz (Lampe/Käfigmodul) des gegenwärtigen Typs BQCXVZ9000/1 beim nächsten von Sharp autorisierten Händler für Projektoren oder beim Kundendienst kaufen. • Die Lampe austauschen. Sie können die Lampe auch bei einem von Sharp autorisierten Händler für Projektoren oder beim Kundendienst austauschen lassen. XV-Z9000U/E Beschreibung der Optik-Einheit Anordnung der optischen Komponenten und zugehörigen Bauteile (Draufsicht) Projektionsobjektiv Prisma DMD-Chips Kondensatorlinse IR-Arretierspiegel Lichtschacht Übertragungslinse Faltspiegel Kondensatorlinse Farbfilter Lampe Gegenstand 1 Lampe 2 Kondensatorlinse, IR-Arretierspiegel und Lichtschacht 3 Farbfilter 4 Übertragungslinse und Faltspiegel 5 Prisma 6 DMD-Chips 7 Projektionsobjektiv Beschreibung Gleichstrom-Lampe mit Parabolreflektor Die Kondensatorlinse führt das Licht von der Lampe zur Endoberfläche des Lichtschachts via dem IR-Arretierspiegel. Der IR-Arretierspiegel wird in diese Einheit eingelegt, um den Wärmeüberschuß von der Lampenenergie zu eliminieren. Das Farbfilter trennt das weiße Licht in die drei Spektralfarben R, G und B. Um die Übergangszeit zwischen den Farbfiltern richtig zu ermitteln, sollte ein Photosensor in das Gerät eingesetzt werden. Die max. Rotationsgeschwindigkeit beträgt 9000 U/min. Das Gerät leitet den Beleuchtungspunkt zum wirksamen Bereich des DMDChips. Das Prisma leitet ebenfalls den Beleuchtungspunkt zum wirksamen Bereich des DMD-Chips. Gleichzeitig leitet es die Reflexionsstrahlen vom DMD-Chip zum Projektionsobjektiv. Der DMD-Chip schaltet jede Farbkomponente per Bildpunkt je nach der Eingangsquelle ein und aus. Das Projektionsobjektiv vergrößert das Objekt und projiziert das von der DMD kommende Einfallslicht. 64 XV-Z9000U/E Einstellung der Spiegel Einstellung des Anzeigebereichs am Bildschirm vornehmen, um Dunkelbereiche am äußeren Bildschirmrand zu vermeiden. 1. Die obere Abdeckung abnehmen, so daß die Optikeinheit sichtbar wird. Nur Weiß am Bildschirm anzeigen. 2. Die Abdeckung 1 der Spiegeleinstellplatte an der Unterseite rechts vom Projektionsobjektiv entfernen. 3. Die drei Schrauben mit dem Spezial-Innensechskantschlüssel (9HPH10XL120) verstellen und so einstellen, daß keine Dunkelbereiche am Bildschirm auftreten. 4. Die Abdeckung 1 der Spiegeleinstellplatte anbringen. 5. Die obere Abdeckung wieder befestigen. Den Innensechskantschlüssel in dieser Richtung einstecken. Vergrößerung von Teil A Einstellen der hinteren Brennweite nach dem Auswechseln des Projektionsobjektivs Hinweis: Ein Klebebandstreifen ist am Scharfeinstellring angebracht (mit dem Ersatz-Projektionsobjektiv mitgeliefert). Dieses Klebeband nicht entfernen, solange die Einstellung nicht abgeschlossen ist. (1) Zwischen dem Gerät und der Leinwand ist ein Abstand von 2,4 m einzuhalten. Danach ist der Zoom-Knopf auf "wide end" einzustellen. (2) Die Objektiveinstellung vornehmen, bis das Projektionsobjektiv das gleiche Niveau wie die Leinwandmitte erreicht hat. (3) Die obere Abdeckung A der Optikeinheit hinter dem Projektionsobjektiv entfernen. (4) Die vier Innensechskantschrauben B auf der Rückseite des Projektionsobjektivs losdrehen. (5) Nun den Einstell-Schraubendreher (C) (9EVDRIVERZ9000) in das Loch D auf der Rückseite des Projektionsobjektivs einführen. Die Bildleinwandmitte scharf einstellen. (Empfohlen wird die Zuführung des SXGA-Signals für 1-PunktWeiß-Kreuzschraffurmuster oder 1-Punkt-Weißmuster auf schwarzem Hintergrund.) (6) Die vier Innensechskantschrauben B auf ein Anzugsdrehmoment von 0,3 Nm (3,06 kg-cm) festziehen und danach Schrauben-Sicherungsmittel (Loctite) aufbringen. (7) Nun das Klebeband vom Scharfeinstellring auf dem Projektionsobjektiv abziehen. (8) Die obere Abdeckung A der Optikmechanismus-Einheit wieder aufsetzen. Schließlich die beiden Schrauben E eindrehen und Loctite auftragen. 65 XV-Z9000U/E Wenn die DMD-Einheit ausgewechselt wurde Hinweis: Der DMD-Chip und die Bildformatiererplatine werden zur gleichen Zeit geliefert. Es wird ausschließlich der DMD-Chip ausgewechselt. Beziehen Sie sich beim Auswechseln der Bildformatiererplatine bitte auf den Abschnitt "AUSBAU DER WICHTIGSTEN BAUTEILE". Die hintere Brennweite des Projektionsobjektivs braucht nicht eingestellt zu werden. Wenn die Brennpunkteinstellung jedoch unzufriedenstellend ist, muß die folgende Einstellung ausgeführt werden. (1) Zwischen dem Gerät und der Leinwand ist ein Abstand von 2,4 m einzuhalten. (2) Die Objektiveinstellung vornehmen, bis das Projektionsobjektiv das gleiche Niveau wie die Leinwandmitte erreicht hat. (3) Die obere Abdeckung A der Optikeinheit hinter dem Projektionsobjektiv entfernen. (4) Die vier Innensechskantschrauben B auf der Rückseite des Projektionsobjektivs losdrehen. (5) Den Zoom-Knopf an der Vorderseite des Projektionsobjektivs auf „tele end“ einstellen und eine gute Scharfeinstellung sicherstellen. (6) Danach ist der Zoom-Knopf an der Vorderseite des Projektionsobjektivs auf „wide end“ einzustellen. (7) Nun den Einstell-Schraubendreher (C) (9EVDRIVERZ9000) in das Loch D auf der Rückseite des Projektionsobjektivs einführen. Die Bildleinwandmitte scharf einstellen. (Empfohlen wird die Zuführung des SXGASignals für 1-Punkt-Weiß-Kreuzschraffurmuster oder 1-Punkt-Weißmuster auf schwarzem Hintergrund.) (8) Den Zoom-Knopf von „wide end“ auf „tele end“ zurückziehen und feststellen, ob die Scharfeinstellung sichergestellt ist. Falls dies nicht der Fall ist, sind die Schritte (5), (6) und (7) solange zu wiederholen, bis die höchste Schärfe erzielt ist. (9) Die vier Innensechskantschrauben B auf ein Anzugsdrehmoment von 0,3 Nm (3,06 kg-cm) festziehen und danach Schrauben-Sicherungsmittel (Loctite) aufbringen. (10) Die obere Abdeckung A der Optikmechanismus-Einheit wieder aufsetzen. Schließlich die beiden Schrauben E eindrehen und Loctite auftragen. E E A C X B B D B B Vergrößerung von Teil X 66 XV-Z9000U/E ELEKTRISCHE EINSTELLUNGEN Einen Signalgenerator bzw. einen PC oder Macintosh-Computer an den Projektor anschließen, um die Signale zuzuführen, die in den Einstellbedingungen aufgeführt sind. Nr. Einstellgegenstand Einstellbedingungen Einstellverfahren 1 EEPROM wird initialisiert 1. Den Netzschalter einschalten und das Gerät für ca. 15 Minuten vorwärmen lassen. (Sicherstellen, daß die Kontrollampe aufleuchtet.) 1. Die folgenden Einstellungen ausführen: Den Schalter SW2002 drücken, um in den Prozeßmodus einzutreten. Die Befehle S2 und S4 am SSS-Menü ausführen. Beim S2-Befehl werden sämtliche Schaltplatinen (außer der PC-Platine) initialisiert. Nicht den S1-Befehl aktivieren, da in diesem Fall auch die PC-Platine initialisiert wird. (Die PC-Platine wurde bereits a Werk eingestellt.) Falls etwa die PC-Karte nachgestellt werden sollte, das Verfahren von "Einstellung der PC-Platine" auf Seite 71 folgen. 2 RGB-Einstellung (auf der PCPlatine) 1. Die 100%- und 0%-Signale für die Farben Rot, Grün und Blau zuführen. INPUT5 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: A/D Position: R-D (R) G-D (G) B-D (B) 1. Die Einstellung solange fortsetzen, bis es am Weißpegel zu Bit-Signalausfällen kommt. Die Einstellung kann mit den Tasten am Gerät oder auf der Fernbedienung erfolgen. 3 DLP-Spannungseinstellung (Referenz) 1. Jede Signaleingabe vermeiden. 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: DLP Position: VOLTAGE 1. Die Einstellung des markierten Bereichs auf der Bildformatiererplatine wählen und sich hierzu auf das Menü beziehen. 2. Diese Einstellung ausführen, wenn der DLP-Chip ausgewechselt wurde, oder wenn die Kombination von DLP-Chip und Bildformatiererplatine verändert wurde. 3. Bereich B C D E Einstellung 1 2 3 4 4 Einstellung des FarbeinstellscheibenIndexes 1. Das Einstellmustersignal für den Farbeinstell-scheibenIndex zuführen. INPUT5 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: DLP Position: CW INDEX 1. Die Einstellung so vornehmen, daß das R-, G- und B-Lampenfarbtonmuster glatt und störungsfrei erscheint. R G B 67 XV-Z9000U/E Nr. Einstellgegenstand Einstellbedingungen Einstellverfahren 5 Einstellung des RGB-Farbtons 1. Das SMPTE-Signalmuster zuführen. INPUT5 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: DLP Position: R-BRIGHT G-BRIGHT B-BRIGHT 1. Sicherstellen, daß die 100%- und 95%-Weißstufen und die 0%- und 5%-Schwarzstufen sichtbar sind. 2. Wenn die Schwarzstufe anderweitig erscheint, abschließend die Einstellungen für R-BRIGHT, GBRIGHT und B-BRIGHT ausführen. 6 Einstellung der Hintergrundfarbe 1. Die nachfolgenden Gruppe bzw. die Positionen wählen: Gruppe: DLP Position: R-GAIN G-GAIN B-GAIN 2. Die Video-Signalkomponente und das 75%-Weißsignal zuführen. 3. Signalpegel: 0,7 ± 0,05 Vs-s (Sync.-Abschnitt nicht eingeschlossen) 4. Anfangseinstellungen von RGAIN, G-GAIN und B-GAIN: 95 5. Ziel-Farbart: x = 0,272 ± 0,005 y = 0,310 ± 0,005 (Farbtemperatur 9500 K + 15 µV) 1. Ein Bild auf eine 40-Zoll Leinwand werfen, dann die Farbart mit einem Farbart-Meßgerät ermitteln. 2. Die G-GAIN-Einstellung bei 95 halten. 3. Die B-GAIN-Einstellung so justieren, daß der y-Wert der Ziel-Farbart zugeschlagen wird. 4. Die R-GAIN-Einstellung so justieren, daß der x-Wert der Ziel-Farbart zugeschlagen wird. 7 Einstellung der Video-Horizontalmitte 1. Ein NTSC-Monoskop- 1. Die Einstellung kann mit den Tasten am Gerät oder mustersignal zuführen. auf der Fernbedienung erfolgen. Die Einstellung INPUT4 solange ausführen, bis das Overscanning links und 2. Die nachfolgende Gruppe rechts ausgeglichen ist. bzw. die Positionen wählen: Gruppe: VIDEO 1 Position: NTSC-H 8 VideoHelligkeitseinstellung 1. Das 10-Stufen-NTSCGrausignal zuführen. 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: VIDEO1 Position: BRIGHT 9 Einstellung des Videobildes 1. Das 10-Stufen-NTSC- 1. Die Einstellung solange fortsetzen, bis es am 100%Grausignal zuführen. Weißpegel zu Bit-Signalausfällen kommt. Die 2. Die nachfolgende Gruppe Einstellung kann mit den Tasten am Gerät oder auf bzw. die Positionen der Fernbedienung erfolgen. wählen: Gruppe: VIDEO1 Position: PICTURE 68 1. Die Einstellung solange fortsetzen, bis es am 0%Schwarzpegel zu mehreren Bit-Signalausfällen kommt. Die Einstellung kann mit den Tasten am Gerät oder auf der Fernbedienung erfolgen. XV-Z9000U/E Nr. Einstellgegenstand Einstellbedingungen Einstellverfahren 10 Einstellung des Video-Farbtons 1. Das interne 8CH-Signal 1. Die folgende fixierte Einstellung überprüfen: (geteiltes FarbbalkenFixierte Einstellung: 128 signal) zuführen. INPUT4 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: VIDEO1 Position: TINT 11 Einstellung der NTSCFarbsättigung 1. Das interne 8CH-Signal (geteiltes Farbbalkensignal) zuführen. INPUT4 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: VIDEO1 Position: N-COLOR 1. Die folgende fixierte Einstellung überprüfen: Fixierte Einstellung: 105 12 Einstellung der PALFarbsättigung 1. Das PAL-Farbbalkensignal zuführen. INPUT4 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: VIDEO1 Position: P-COLOR 1. Die folgende fixierte Einstellung überprüfen: Fixierte Einstellung: 110 13 Einstellung der SECAMFarbsättigung 1. Das SECAM-Farbbalkensignal zuführen. INPUT4 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: VIDEO1 Position: S-COLOR 1. Check the fixed setting. Fixed setting: 110 14 Einstellung der DTV-Helligkeit Diesen Verfahren nur für Modell XVZ9000 vornehmen.) 1. Das 100%-Farbbalkensignal (Komponentensignal) oder das 10-Stufen-Grausignal dem Eingangsanschluß 4801 zuführen. INPUT 2 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: DVD Position: BRIGHT 1. Die Einstellung solange fortsetzen, bis es am 0%Schwarzpegel zu mehreren Bit-Signalausfällen kommt. Die Einstellung kann mit den Tasten am Gerät oder auf der Fernbedienung erfolgen. 15 Einstellung für DTV-Kontrast (Diesen Verfahren nur für Modell XVZ9000 vornehmen.) 1. Das 100%-Farbbalkensignal (Komponentensignal) oder das 10-Stufen-Grausignal dem Eingangsanschluß 4801 zuführen. INPUT 2 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: DVD Position: CONTRAST 1. Die Einstellung solange fortsetzen, bis es am 100%Weißpegel zu Bit-Signalausfällen kommt. Die Einstellung kann mit den Tasten am Gerät oder auf der Fernbedienung erfolgen. 69 XV-Z9000U/E Nr. Einstellgegenstand Einstellbedingungen Einstellverfahren 16 Einstellung der DVDFarbsättigung und des DVDFarbtons 1. Das 100%-Farbbalkensignal (4801-Komponentensignal) den Eingangsanschlüssen Y, Pb und Pr zuführen. INPUT 2 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: DVD Position: TINT 1. Die folgende fixierte Einstellung überprüfen: Fixierte Einstellung: TINT : 32 COLOR : 36 17 Überprüfung und Nachstellung der Weißbalance 1. Den für Posten 11 beschriebenen Einstellbedingungen folgen. Sicherstellen, daß zwischen dem Gerät und dem Standard-Monitor kein Unterschied in der Weißbalance besteht. 18 Überprüfung der Farbleistung 1. Das Farbbalkensignal zuführen. 1. L1 von der Prozeßmodus-Leitung wählen. Die Farb- und Farbtonleistung überprüfen. 19 Überprüfung der Videoleistung 1. Das Monoskopmustersignal zuführen. 1. L2 von der Prozeßmodus-Leitung wählen. Die Leistung von Bild, Helligkeit und Schärfe überprüfen. 20 Überprüfung der RGBLeistungswerte 1. Das RGB-Signal zuführen. 1. L4 von der Prozeßmodus-Leitung wählen. Die Leistung von Bild, Helligkeit, Rot, Blau, Takt, Phase, Horizontal- und Vertikalposition überprüfen. überprüfen. 21 Leistung des AusschaltTimers 22 Überprüfung der Thermistorleistung 1. Den Thermistor mit einem Haartrockner erwärmen. 1. Sich vergewissern, daß die angegebene Temperatur erreicht ist. 23 Überprüfung der Auto-SyncLeistungswerte 1. Das Phasen-Prüfmustersignal zuführen. In den Betriebsarten VGA, SVGA und XGA ist sicherzustellen, daß der Takt, die Phase, die Horizontalund Vertikalpositionseinstellungen automatisch eingestellt werden können. 24 Auslieferungseinstellungen 1. OFF von der Prozeßmodus-Leitung wählen. Sicherstellen, daß der Ausschalt-Timer nach 5minütiger Bildschirmanzeige aktiviert wird und sich das Gerät innerhalb von 5 Minuten ausschaltet. 1. Folgende Einstellungen sind vorzunehmen: 70 Verkaufsbereich Einstellverfahren Fernbedienungs-Einstellung XV-Z9000U S4 Werkseinstellung 4 XV-Z9000E S3 Werkseinstellung 3 XV-Z9000U/E Einstellung der PC-Platine 1. Initialisierung des EEPROM 1) Den Schalter SW2002 drücken, um den Prozeßmodus aufzurufen. 2) Den S1-Befehl am SSS-Menü ausführen. (Der S1-Befehl dient dazu, die Platine alleine zu initialisieren. Der S2-Befehl darf allerdings nicht eingegeben werden, da hierdurch auch alle anderen Einstelldaten der Platine initialisiert werden.) 3) Sich vergewissern, daß es sich bei der Programmversion VER.XXX des SPECIAL-Menüs um die neueste Version handelt. 2. Einstellung der Pegel 2.1 Vorbereiten des Oszilloskops Das Oszilloskop auf einen Bereich zwischen 1 V/div. und 5 µs/div. einstellen. 2.2 Anschließen der PC-Schnittstelle 1) Das spezifizierte Kabel zwischen der Analog-Ausgangsbuchse (Signalgenerator) und dem DUSB-Anschluß (INPUT5 am Projektor) anschließen. Den Projektor-Eingangswahlschalter auf INPUT5 einstellen. 2) Den Signalgenerator auf den XGA-Modus stellen (1024 x 768, 60 Hz, 32 Farbtöne). Die Ausgangsamplitude zwischen Schwarz- und Weißpegel auf 700 mVs-s (Abschluß mit 75-Ohm-Impedanz) einstellen. 3) Die Stromversorgung einschalten. 2.3 Überprüfung und Einstellung der Pegel 1) Den Schalter SW2002 drücken, um den Prozeßmodus aufzurufen. 2) Einstellung von R-BRIGHT: Den Schwarzpegel des Rotsignals zuführen, dann den R-BRIGHT-Parameter der Gruppe A/D so einstellen, bis Bit-Dropouts auftreten. 3) Einstellung von B-BRIGHT: Den Schwarzpegel des Blausignals zuführen, dann den B-BRIGHT-Parameter der Gruppe A/D so einstellen, bis Bit-Dropouts auftreten. 4) Einstellung von G-BRIGHT: Den Schwarzpegel des Grünsignals zuführen, dann den G-BRIGHT-Parameter der Gruppe A/D so einstellen, bis Bit-Dropouts auftreten. 2.4. Einstellung der DTV-Parameter 1) Das Signal dem RCA-Eingangsanschluß von INPUT2 zuführen. 2) Den Signalgenerator mit dem Weißsignal auf den 1080i 60Hz-Modus einstellen. Die Ausgangsamplitude zwischen Schwarz- und Weißpegel auf 700 mVs-s einstellen. 3) Das spezifizierte Kabel zwischen dem Analogausgang (Signalgenerator) und dem RCA-Anschluß (INPUT2 am Projektor) anschließen. 4) Die G-BRIGHT-Einstellung gleich ausführen wie die G-BRIGHT-Einstellung der Gruppe A/D. 5) Die Einstellung für CB-OFFSET von Gruppe DTV auf 20 setzen. 6) Die Einstellung für CR-OFFSET von Gruppe DTV auf 20 setzen. 7) Bei den bestimmten CB-OFFSET- und CR-OFFSET-Einstellungen, 5 Punkten zur G-BRIGHT-Einstellung für Modell XV-Z9000U und 4 Punkten für Modell XV-Z9000E addieren. 8) Den Schalter SW2002 drücken, um den Prozeßmodus zu verlassen. 71 XV-Z9000U/E Prozeßmenü 1 Gruppe Untergruppe Position Adjust PC Image A/D R-BRIGHT G-BRIGHT B-BRIGHT R-D B-D G-D Adjust HDDE formatter DLP VOLTAGE CW-INDEX R-BRIGHT G-BRIGHT B-BRIGHT R-GAIN G-GAIN B-GAIN Adjust Component DTV (High Definition) G-BRIGHT CB-OFFSET CR-OFFSET Adjust VIDEO Image VIDEO1 NTSC-H PICTURE BRIGHT TINT N-COLOR P-COLOR S-COLOR SET UP SET UP B SET UP C VIDEO2 PEAK FIL PEAK GAIN PEAK COR N358 DLY N433 DLY PAL DLY SECAM DLY Adjust Component (480i) DVD CONTRAST BRIGHT TINT COLOR 72 XV-Z9000U/E Prozeßmenü 2 Gruppe Untergruppe Position Process mode LINE L1 L2 L3 L4 OFF TEMP OFF SENSOR CHECK INITIAL SETTING SSS TIME S1 S2 S3 S4 S5 LAMP Sample Pattern PATTERN RGB RGB(50) CROSS STEP COLOR CHR Adjust CVIC CVIC MODDE -PROGRESSIVE IP FILM PTG MSW LSW C-LEVEL C-LIMIT C-LPF C-THRESH C-MISSTH C-MOVIEA C-MOVIEB C-MOVIEC 73 XV-Z9000U/E Prozeßmenü 3 Gruppe Untergruppe Position Adjust CVIC CVIC BBN-TBL0 -ENHANCE-VIDEO BBN-TBL1 DFC-TBL0 DFC-DIR0 DFC-EDG0 DFCTBL1 DFC-DIR1 DFC-EDG1 CVIC BBN-TBL0 -ENHANCE-HDTV BBN-TBL1 DFC-TBL DFC-DIR DFC-EDG CVIC BBN-GAIN0 -ENHANCE-RGB BBN-GAIN1 BBN-GAIN2 BBN-TBL DFC-TBL DFC-DIR DFC-EDG CVIC CUBIC-RGB -SCREEN CUBIC-VIDEO CVIC XEGTH -IDC XLTH1-H XLTH1-L XLTH2-H XLTH2-L VEGTH VLTH1-H VLTH1-L VLTH2-H VLTH2-L Version Check etc. (High Definition) Special IPL E2PROM ADR RD/RW 74 XV-Z9000U/E FEHLERSUCHTABELLE Überprüfung der allgemeinen Leistung Blinkt die POWER-LED rot oder blau? NEIN Zur "Überprüfung des Netzgeräts" weitergehen. JA Wird das Gerät durch die Netztaste auf der Fernbedienung eingeschaltet? NEIN JA Läuft das Kühlgebläse? Leuchtet die Lampe? NEIN Zur "Überprüfung der Lampenfunktion" weitergehen. JA Wird das Benutzermenü angezeigt? NEIN Den Bildformatierer-schaltkreis und seine peripheren Schaltkreise überprüfen. JA Ist das Videoeingangssignal wie spezifiziert? NEIN JA Ist der Komponenteneingang wie spezifiziert? JA NEIN Ist der RGB-Eingang wie spezifiziert? NEIN JA Liegen Ausgangssignale an den Stiften (32), (34) und (37) von P3580 an? NEIN Den Schaltkreis des IC2505 und seine peripheren Schaltkreise überprüfen. Liegen Ausgangssignale an den Stiften (41) bis (60) von P3580 an? NEIN Den Schaltkreis des IC2505 und seine peripheren Schaltkreise überprüfen. NEIN Den Schaltkreis des IC2505 und seine peripheren Schaltkreise überprüfen. NEIN Den Schaltkreis des IC2005 und seine peripheren Schaltkreise überprüfen. Die peripheren Schaltkreise des PC- Platinenschaltkreises überprüfen. JA Funktioniert die RS-232CSchnittstelle? Zur "Überprüfung der peripheren Micro-computerKomponenten" und "Überprüfung der PCPlatine" weitergehen. NEIN Liegen Ausgangssignale an den Stiften (41) bis (60) von P3580 an? Empfohlene NEIN Kommunikationssoftware: "TERA TERM" Die folgenden Einstellungen Liegen Ausgangssignale an vornehmen: den Stiften (32), (34) und Baud-Rate = 9600 bps, (37) von P3580 an? Bitlänge = 8 Bits, Stop-Bit = 1, Parität = keine Die RETURN-Taste auf der Tastatur drücken. Erscheint "ERR" erneut? JA ENDE 75 XV-Z9000U/E Überprüfung der Stromversorgung Sind alle Steckverbindungen innerhalb der Stromversorgung fest angeschlossen? NEIN Die Steckverbinder CN7105, 7103, 7101 und 7102 gut einstecken. JA Ist die Lampenabdeckung vollkommen geschlossen? NEIN JA NEIN Funktioniert der Bimetallschalter? Den Bimetallschalter auswechseln oder den roten Knopf zwecks Rückstellung drücken. JA Wird dem Relais RL7001 Netzspannung zugeführt? NEIN JA Wird dem L7005 Netzspannung zugeführt? F7001 auswechseln. NEIN F7002 auswechseln. JA Wird dem C7151 ca. 6VGleichspannung zugeführt? NEIN JA Wird dem CN7003 ca. 340V-Gleichspannung zugeführt? Die Lampenabdeckung mit den Schrauben gut festziehen. NEIN JA Liegen die spezifizierten NEIN Spannungen an den Ausgangsanschlüssen von CN7101 und CN7102 an? JA Die PlatinenAusgangsschaltkreise überprüfen. 76 Die peripheren Schaltkreise von Q7101 bis Q7107 überprüfen. Wenn erforderlich, die entsprechenden Komponenten auswechseln. Die Schaltkreise zur Primärseite von T7002 auf Beschädigung überprüfen. Wenn erforderlich, die entsprechenden Komponenten auswechseln. Die Schaltkreise zur Sekundärseite von T7002 auf Beschädigung überprüfen. Wenn erforderlich, die entsprechenden Komponenten auswechseln. XV-Z9000U/E Überprüfung der PCPlatine 0 Wird das Benutzermenü richtig angezeigt? JA NEIN Die Bildschirmanzeige überprüfen. Den DTV RGB-Eingang überprüfen. Den DTVKomponenteneingang überprüfen. Den VIDEO-Eingang überprüfen. Den normalen Signalfluß überprüfen. Der Signalfluß vom CVIC_IC zum Panel-Ausgangsanschluß ist gleich wie für die Komponente und die Videosignale. Deshalb werden die Leitungssignale nach CVIC nicht geprüft. (Die 480i- und 580iKomponentensignale sind nicht miteingeschlossen.) Das Signal läuft durch die gleichen Schaltkreise wie das DTV RGB-Signal. Den SOG-Schaltkreis (Sync On Green) und den Farbeinstell-Schaltkreis überprüfen. (Die 480i- und 580iKomponentensignale sind nicht miteingeschlossen.) Das Videosignal fließt durch eine unterschiedliche Route vom RGB-Signal und geht zum CVIC_IC. Deshalb sind die ICs der Videosignale zu überprüfen. Das D-SUB-Eingangssignal überprüfen. Den D-SUB-Eingang überprüfen. Ende 77 XV-Z9000U/E Überprüfung des RGBEingangs Das synchron-getrennte DTV RGB-Signal dem INPUT1 oder INPUT2 zuführen. (Die 480iund 580i-Komponentensignale sind nicht miteingeschlossen.) 1 INPUT1 oder INPUT2 mit der Taste auf der Frontplatte oder auf der Fernbedienung anwählen. 2 Erscheint das Bild? NEIN Überprüfen, ob das Videoeingangssignal wie spezifiziert ist. JA Treten Bildstörungen auf? NEIN Zur "Überprüfung des Synchronsignals" weitergehen. JA 3 Erscheinen die Farben R, G und B? NEIN Zur "Überprüfung des RGBSignals" weitergehen. JA Sind die Konturen wie spezifiziert? NEIN Ende JA Der IC8004 oder seine peripheren Schaltkreise sind defekt. 78 XV-Z9000U/E Überprüfung des Videoeingangs Sicherstellen, daß die Eingangssignaleinstellung wie spezifiziert ist. JA Liegt am Anschluß des C8077 ein Videosignal an? NEIN Defekte Eingangsplatine. JA Das Synchronsignal überprüfen. JA IC8025 und IC8004 sind defekt. Überprüfung der Eingangssignaleinstellung Ist die Eingangssignaleinstellung wie spezifiziert? NEIN Das spezifizierte Signal anwählen. JA 2 Ist der Stecker richtig angeschlossen? NEIN Den Stecker wieder anschließen. JA Ende 1 79 XV-Z9000U/E Überprüfung des Synchronsignals Liegt am TL8134 ein Vertikal-Synchronsignal an? NEIN JA Liegt am TL8133 ein Horizontal-Synchronsignal an? NEIN Die Eingangssignaleinstellung überprüfen. JA Defekte Eingangsplatine. Liegt am TL8131 ein Vertikal-Synchronsignal an? NEIN JA Liegt am TL8130 ein Horizontal-Synchronsignal an? NEIN IC8302, IC8325, IC8299 oder ihre peripheren Schaltkreise sind defekt. JA Sind die Vertikal- und Horizontal-Synchronsignale zeitlich abgestimmt? NEIN Es besteht kein Problem mit dem Synchronsignal. Ende. JA Ist der Signalgenerator (Eingangsquelle) wie spezifiziert? NEIN Die spezifizierten Signalquelleneinstellungen vornehmen. JA Defekte Eingangsplatine. 2 80 XV-Z9000U/E Überprüfung des RGBSignals Ist der Signaltyp auf RGB eingestellt? JA Auf das RGB-Signal einstellen. NEIN Den Prozeßmodus abrufen. R, G und B separat am Mustermenü anwählen. Zur "Überprüfung der peripheren Schaltkreise des GA4" weitergehen. Den Signalgenerator in den Abstufungssignalmodus bringen, um das Eingangssignal zu überprüfen. Die Abstufungssignale am TL8073, TL8074, TL8075 und TL8080 messen. Liegen spezifizierte Signale am TL8073, TL8074, TL8075 und TL8080 an? JA NEIN Liegen Eingangssignale am C8069 und C8061 an? JA Der IC8025 oder sein peripherer Schaltkreis ist defekt. Der IC8004 oder sein peripherer Schaltkreis ist defekt. 81 NEIN Defekte Eingangsplatine. XV-Z9000U/E Überprüfung der peripheren Schaltkreise des GA4 Den Prozeßmodus abrufen und R, G und B separat am Mustermenü anwählen. Liegen spezifizierte R-, Gund B-Videoausgangssignale an? JA Ende der Überprüfung für die peripheren Schaltkreise des GA4. NEIN Sind die gemessenen Signale mit den vom Mustermenü gewählten Signalen identisch? NEIN Liegt am R974 ein Taktsignal an? JA Defekte Ausgangsplatine. NEIN Liegt ein Taktsignal (37,125 MHz) am TL8114 an? JA JA Defekter IC8029. NEIN Liegt ein Taktsignal (37,125 MHz) am FL8110 an? NEIN Defekter X8005. JA Defekter IC8025. Liegen am TL8026, TL8027 und TL8028 Synchronsignale an? NEIN Liegen Synchronsignale am TL8112 und TL8133 an? JA Mit einem Oszilloskop die Signale von TL8141 bis TL8148 messen. Sind die gemessenen Signale mit den vom Mustermenü gewählten Signalen identisch? JA Defekter IC8029. NEIN Defekte Digitalanzeigeplatine. JA Mit einem Oszilloskop die Signale von TL8106 bis TL8111 messen. Sind die gemessenen Signale mit den vom Mustermenü gewählten Signalen identisch? NEIN Defekter IC8025. JA Defekter IC8029. 82 NEIN Defekter IC8025. XV-Z9000U/E Überprüfung der Komponenteneingänge (außer für 480i) Das Komponentensignal dem INPUT1 oder INPUT2 zuführen. INPUT1 oder INPUT2 mit der Taste auf der Frontplatte oder auf der Fernbedienung anwählen. Erscheint das Bild? JA 4 Sind die Farben wie spezifiziert? NEIN Zur „Überprüfung des SOG -Schaltkreises“ weitergehen. JA NEIN Ist der Signaltyp auf COMPONENT eingestellt? NEIN JA Den Signaltyp auf COMPONENT einstellen? Die Prozeßeinstellung ausführen. NEIN 4 Ist die Bildkontur wie spezifiziert? JA IC8004 oder IC8025 sind defekt. NEIN Ende der Überprüfung des Komponenteneingangs. 83 XV-Z9000U/E Überprüfung des SOGSchaltkreises Das Signal mit dem Oszilloskop am TL8136 messen. Wird das Farbsynchronsignal JA zeitlich wiedergegeben? NEIN Mit dem Oszilloskop am Anschluß des C8069 messen. Liegt das Y-Signal einschließlich dem Synchronsignal an? JA Es besteht kein Problem mit dem SOG-Schaltkreis. NEIN Zur „Überprüfung der Eingangssignaleinstellungen“ weitergehen. Defekter SOG-Synchron signal-Trennschaltkreis. Defekte Eingangsplatine. Überprüfung der Bildschirmanzeige Erscheint die Bildschirmfarbe normal? JA NEIN Zur „Überprüfung der peripheren Schaltkreise des GA4“ weitergehen. Die Einstellung des Ausgangsleitungssignals im Einstellverfahren ausführen. Den Flash-ROM-Chip erneut programmieren. 0 84 XV-Z9000U/E Überprüfung des Videoausgangs Das Farbbildsignal dem INPUT4 zuführen. INPUT4 mit der Taste auf der Frontplatte oder auf der Fernbedienung anwählen. VIDEO als Signaltyp am Benutzermenü wählen. 5 Erscheint das Bild? NEIN JA Bestehen Bildstörungen? NEIN Sind die Konturen wie spezifiziert? Zur „Überprüfung des Videosynchronsignals“ weitergehen. JA NEIN NEIN Zur „Überprüfung des Videosynchronsignals“ weitergehen. Das Einstellverfahren ausführen. JA Es besteht kein Problem mit dem Videoe ingangssignal. Ende. 5 Liegt ein Videosignal am Stift (72) von IC8338 an? Ist das Videoeingangssignal JA wie spezifiziert? NEIN Defekter IC8338. 6 85 XV-Z9000U/E 6 Das VPC-Taktsignal (IC8338) am TL8004 messen. Ist das Taktsignal wie spezifiziert? NEIN JA Defekter IC8338. Zur „Überprüfung des Videosynchronsignals“ weitergehen. Der IC8025 oder sein peripherer Schaltkreis ist defekt. Überprüfung des Videosynchronsignals Mit dem Oszilloskop das Signal am TL8140 messen. (Das VertikalSynchronsignal überprüfen.) Ist das Vertikal-Synchron signal wie spezifiziert? NEIN JA Mit dem Oszilloskop das Signal am TL8142 messen. (Das HorizontalSynchronsignal überprüfen.) Ist das Horizontal-Synchron NEIN signal wie spezifiziert? JA Zur „Überprüfung der Eingangssignaleinstellung“ weitergehen. Defekte Eingangsplatine. 7 86 XV-Z9000U/E Überprüfung des D-SUB-Eingangs Das PC-RGB-Signal dem INPUT5 zuführen. INPUT5 als Eingang wählen. NEIN Sicherstellen, das R-, G- und BSignale an den Stiften (126), (136) und (146) des IC8004 anliegen. Erscheint das Bild? JA Bestehen Bildstörungen? JA NEIN Liegen die Signale R, G und B an? NEIN JA 3 Die Vertikal- und Horizontalsynchronsignale am Stift (6) von IC8364 und am Stift (6) von IC8385 überprüfen. Sind die Signale wie spezifiziert? JA Liegen die Vertikal- und Horizontalsynchronsignale am TL8130 und TL8131 an? JA NEIN Der Synchronsignal-Trennschaltkreis von IC8354 und IC8365 oder ihre peripheren Schaltkreise sind defekt. NEIN Der IC8302 oder sein peripherer Schaltkreis ist defekt. Der IC8025 und IC8004 oder ihre peripheren Schaltkreise sind defekt. 87 Der D-SUB-Stecker oder sein peripherer Schaltkreis ist defekt. XV-Z9000U/E Überprüfung der Lampenfunktion Die Lampe leuchtet nicht auf. Wird bei Einschalten des Gerätes ein Entladungsgeräusch wahrgenommen? JA NEIN Laufen die Kühlgebläse ordnungsgemäß? NEIN JA Liegen 340-VGleichspannung am Vorschaltgerät-Schaltkreis CP1001 an? JA NEIN Ist die Lampe oder die FarbeinstellscheibenLeitungsfassung nicht richtig angebracht? JA Die Lampe oder die Farbeinstellscheibe auswechseln. Den Stromschaltkreis oder den Gebläseschaltkreis am Hauptschaltkreis überprüfen. Den Stromschaltkreis überprüfen. Liegen 3,5-V-Spannung am Stift (1) des Vorschaltgerät- NEIN Schaltkreises CP1501 an? JA Mikroprozessorschaltkreis überprüfen. Die VorschaltgerätLeistungsplatine auswechseln. Die VorschaltgerätLeistungsplatine überprüfen. Den Mikroprozessorschaltkreis überprüfen. 88 NEIN Die Fassungen gut befestigen. XV-Z9000U/E Keine Horizont alsynchronisation Ist der TerminalEingangsanschluß wie spezifiziert? Ist das Kabel fest angeschlossen? NEIN JA Liegt am Stift (14) des IC2506 ein HorizontalSynchronsignal an? NEIN Das vorgeschriebene Kabel benutzen, einstecken und gut befestigen. Die Leitung zwischen dem IC2506 und dem Eingangsterminal überprüfen. JA Liegt am Stift (11) des IC2509 ein HorizontalSynchronsignal an? JA NEIN Die Leitung zwischen IC2506 undIC2509 überprüfen. Zur „PC Board Störungssuche“ weitergehen. Keine Vertikalsynchronisation Ist der TerminalEingangsanschluß wie spezifiziert? Ist das Kabel fest angeschlossen? NEIN Liegt am Stift (14) des IC2501 ein VertikalSynchronsignal an? JA Das vorgeschriebene Kabel benutzen, einstecken und gut befestigen. NEIN JA Liegt am Stift (8) des IC2509 ein VertikalSynchronsignal an? JA NEIN Die Leitung zwischen dem IC2501 und dem Eingangsterminal überprüfen. Die Leitung zwischen IC2506 und IC2509 überprüfen. Zur „PC Board Störung ssuche“ weitergehen. 89 XV-Z9000U/E Überprüfung des IC3504 (3DRauschunterdrückung) und seiner peripheren Schaltkreise. Liegen Eingangssignale an NEIN den Stiften (88) (Y-Signal) und (96) (C-Signal) von IC3504 an? JA Liegen Ausgangssignale an den Stiften (84) (YSignal) und (83) (C-Signal) von IC3504 an? JA Den Eingangssignal schaltkreis des IC2505 und seine peripheren Schaltkreise überprüfen. NEIN Der IC3504 und sein peripherer Schaltkreis ist defekt. Die Leitung zum PCKartenanschluß bzw. die Schaltkreise überprüfen, welche der PC-Karte folgen. 90 XV-Z9000U/E Überprüfung der Komponenten- und RGB-Eingänge Liegen Signale an den Stiften (34), (36) und (38) von IC2505 an? NEIN Den Eingangssignal schaltkreis oder den IC2505 und seine peripheren Schaltkreise überprüfen. JA Liegen Signale an den Stiften (3), (5) und (6) von IC2507 an? JA Liegen Signale an den Stiften (56/26), (58/28) und (60/30) von P3580 an (Anschlußstellen zwischen den Steckkarten)? Die Anschlußstellen zwischen den Steckkarten überprüfen bzw. die Schaltkreise, die der PCKarte folgen. Es liegen keine RGBFarben vor. JA Den Schaltkreis der nicht erscheinenden Farbe überprüfen. NEIN Die Leitung zwischen dem Q2509 und Q2517 und seine peripheren Schaltkreise bzw. den IC2507 überprüfen. NEIN Die Leitung zwischen dem Q2518 und Q2520 und seine peripheren Schaltkreise überprüfen. JA Liegen Signale an den Stiften (49/19), (51/21) und (53/23) von P3580 an (Anschlußstellen zwischen den Steckkarten)? JA NEIN NEIN Die Leitung zwischen dem Q2525 bis Q2523 und Q2524 sowie seine peripheren Schaltkreise überprüfen. 91 NEIN Es liegen keine RGBFarben vor. JA Den Schaltkreis der nicht erscheinenden Farbe überprüfen. XV-Z9000U/E XV-Z9000U/E CHASSIS LAYOUT / CHASSIS-ANORDNUNG H G F E D C B A 1 2 3 4 5 6 92 7 8 9 10 11 12 13 14 15 93 16 17 18 19 XV-Z9000U/E XV-Z9000U/E BLOCK DIAGRAM / BLOCKSCHALTBILD H G F E D C B A 1 2 3 4 5 6 94 7 8 9 10 11 12 13 14 15 95 16 17 18 19 XV-Z9000U/E XV-Z9000U/E OVERALL WIRING DIAGRAM / GESAMTSCHALTPLAN H G F E D C B A 1 2 3 4 5 6 96 7 8 9 10 11 12 13 14 15 97 16 17 18 19 XV-Z9000U/E DESCRIPTION OF SCHEMATIC DIAGRAM BESCHREIBUNG DES SCHEMATISCHEN SCHALTPLANS VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Voltages at test points are measured at the supply voltage of AC 220V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. 1. Spannungen an den Prüfpunkten werden bei einer Netzspannung von 220V gemessen, Signale werden für die Wartung mit einem Farbbalken-Signal generator zugeführt, und Spannungen werden mit einem Meßinstrument (20 kΩ/V) ermittelt. WAVEFORM MEASUREMENT CONDITION: SIGNALFORMMESSUNGEN: 1. Waveforms at test points are observed at the supply voltage of AC 220V. Signals are fed by a color bar signal generator for servicing purpose. INDICATION OF RESISTOR & CAPACITOR: RESISTOR 1. The unit of resistance “Ω” is omitted. (K=kΩ=1000 Ω, M=MΩ). 2. All resistors are ± 5%, unless otherwise noted. (J= ± 5%, F= ± 1%, D= ± 0.5%) 3. All resistors are 1/10W, unless otherwise noted. 4. All resistors are Carbon type, unless otherwise noted. W : Cement C : Solid S : Oxide Film T : Special N : Metal Coating CAPACITOR 1. All capacitors are µF, unless otherwise noted. (P=pF=µµF). 2. All capacitors are 50V, unless otherwise noted. 3. All capacitors are Ceramic type, unless otherwise noted. (ML): Mylar (TA): Tantalum (PF): Polypro Film (ST): Styrol 1. Die Wellenformen an den Testpunkten werden bei einer Netzspannung von 220V verfolgt. Signale werden für die Wartung mit einem Farbbalken-Signal generator zugeführt. BEZEICHNUNG DES WIDERSTANDS UND KONDENSATORS: WIDERSTAND 1. Die Widerstandseinheit “Ω” wird weggelassen. (K=kΩ=1000 Ω, M=MΩ) 2. Alle Widerstände haben ± 5%, sofern nicht anders angegeben.(J= ± 5%, F= ± 1%, D= ± 0.5%) 3. Alle Widerstände haben 1/10W, sofern nicht anders angegeben. 4. Alle Widerstände sind Kohletyp, sofern nicht anders angegeben. W : Cement C : Solid S : Oxide Film T : Special N : Metal Coating KONDENSATOR 1. Die Kapazitätseinheit ist µF, sofern nicht anders angegeben. (P=pF=µµF). 2. Alle Kondensatoren haben 50V, sofern nicht anders angegeben. 3. Alle Kondensatoren sind Keramiktyp, sofern nicht anders angegeben. (ML): Mylar (TA): Tantal (PF): Polyprofilm (ST): Styrol CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours. ACHTUNG: Bei diesem Schaltplan handelt es sich um den ursprünglichen. Esönnen daher geringfügige Unterschiede zu dem lhrem bestehen. SAFETY NOTES: 1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACEING PARTS. 2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING. SICHERHEITSANMERKUNGEN: IMPORTANT SAFETY NOTICE: WICHTIGE SICHERHEITSANMERKUNGEN: 1. VOR DEM AUSWECHSELN VON TEILEN MUSS UNBEDINGT NETZSTECKER AUS DER NETZSTECKDOSE GEZOGEN WERDEN. 2. DIE WARMEABLEITER DER HALBLEITER SOLLTEN BEIM BETRIEB DES CHASSIS ALS MÖGLICHE URSACHEN VON GEFÄHRLICHEN ELEKTRISCHEN SCHLÄGEN BETRACHTET WERDEN. PARTS MARKED WITH “å” ( ) ARE IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET. MIT “å ”( )BEZEICHNETEN TEILE SIND BESONDERS WICHTIG FÜR DIE AUFRECHTERHALTUNG DER SICHERHEIT . BEIM WECHDIESER TEILE SOLLTEN DIE VORGESCHRIEBENEN TEILE IMMER VERWENDET WERDEN, UM SOWOHL DIE SICHERHEIT ALS AUCH DIE LEISTUNG DES GERÄTES AUFRECHTZUERHALTEN. 98 XV-Z9000U/E WAVEFORMS / WELLENFORMEN 1 P3580 32 (VIDEO AC) H : 20µ sec/div V : 500mV/div 2 P3580 34 (Y-signal) H : 10µ sec/div V : 0.2V/div 3 P3580 4 (CHROMA signal) H : 10µ sec/div V : 0.2V/div 4 P3580 47 (RGB) H : 20µ sec/div V : 1V/div 5 P3580 17 (RGB) H : 5m sec/div V : 2V/div 6 P3580 49 (RGB AC) H : 20µ sec/div V : 200mV/div 7 P3580 51 (RGB AC) H : 20µ sec/div V : 500mV/div 8 P3580 53 (RGB AC) H : 20µ sec/div V : 200mV/div 99 XV-Z9000U/E XV-Z9000U/E Ë MAIN UNIT / HAUPT-EINHEIT -1/5 H G F E D C B A 1 2 3 4 5 100 6 7 8 9 10 11 12 13 14 15 101 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë MAIN UNIT / HAUPT-EINHEIT -2/5 H G F E D C B A 1 2 3 4 5 102 6 7 8 9 10 11 12 13 14 15 103 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë MAIN UNIT / HAUPT-EINHEIT -3/5 H G F E D C B A 1 2 3 4 5 104 6 7 8 9 10 11 12 13 14 15 105 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë MAIN UNIT / HAUPT-EINHEIT -4/5 H G F E D C B A 1 2 3 4 5 106 6 7 8 9 10 11 12 13 14 15 107 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë MAIN UNIT / HAUPT-EINHEIT -5/5 H G F E D C B A 1 2 3 4 5 108 6 7 8 9 10 11 12 13 14 15 109 16 17 18 19 XV-Z9000U/E Ë KEY UNIT / TASTE-EINHEIT H G F E D C B A 1 2 3 4 110 5 6 XV-9000U/E Ë R/C RECEIVER (Front) Unit / EINLASSEINHEIT (Vorder) H G F E Ë R/C RECEIVER (Rear) Unit / EINLASSEINHEIT (Hinter) D C B A 1 2 3 4 111 5 6 XV-Z9000U/E XV-Z9000U/E Ë POWER UNIT / NETZTEINHEIT H G F E D C B A 1 2 3 4 5 112 6 7 8 9 10 11 12 13 14 15 113 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-1/9 H G F E D C B A 1 2 3 4 5 114 6 7 8 9 10 11 12 13 14 15 115 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-2/9 H G F E D C B A 1 2 3 4 5 116 6 7 8 9 10 11 12 13 14 15 117 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-3/9 H G F E D C B A 1 2 3 4 5 118 6 7 8 9 10 11 12 13 14 15 119 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-4/9 H G F E D C B A 1 2 3 4 5 120 6 7 8 9 10 11 12 13 14 15 121 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-5/9 H G F E D C B A 1 2 3 4 5 122 6 7 8 9 10 11 12 13 14 15 123 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-6/9 H G F E D C B A 1 2 3 4 5 124 6 7 8 9 10 11 12 13 14 15 125 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-7/9 H G F E D C B A 1 2 3 4 5 126 6 7 8 9 10 11 12 13 14 15 127 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-8/9 H G F E D C B A 1 2 3 4 5 128 6 7 8 9 10 11 12 13 14 15 129 16 17 18 19 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-9/9 H G F E D C B A 1 2 3 4 5 130 6 7 8 9 10 11 12 13 14 15 131 16 17 18 19 XV-Z9000U/E Ë LED UNIT/ LED-EINHEIT H G F E D C B A 1 2 3 4 5 132 6 7 8 9 10 XV-Z9000U/E H PRINTED WIRING BOARD ASSEMBLIES LEITERPLATTENEINHEITEN G F E Power Unit (Component Side) Netzteinheit (Bestückungsseite) D C B A Power Unit (Wiring Side) Netzteinheit (Leiterbahnseite) 1 2 3 4 133 5 6 XV-Z9000U/E H G F E D C B A Main Unit (Component Side) Haupt-einheit (Bestückungsseite) 1 2 3 4 134 5 6 XV-Z9000U/E H G F E D C B A Main Unit (Wiring Side) Haupt-einheit (Leiterbahnseite) 1 2 3 4 135 5 6 XV-Z9000U/E H G Key Unit (Component Side) Taste-Einheit (Bestückungsseite) F E D R/C Receiver (Rear) Unit (Component Side) Einlasseinheit (Hinter) (Bestückungsseite) R/C Receiver (Front) Unit (Component Side) Einlasseinheit (Vorder) (Bestückungsseite) C B LED Unit (Component Side) LED-Einheit (Bestückungsseite) A 1 2 3 4 136 5 6 XV-Z9000U/E H G Key Unit (Wiring Side) Taste-Einheit (Leiterbahnseite) F E R/C Receiver (Rear)Unit (Wiring Side) Einlasseinheit (Hinter) (Leiterbahnseite) D R/C Receiver (Front)Unit (Wiring Side) Einlasseinheit (Vorder) (Leiterbahnseite) C B LED Unit (Wiring Side) LED-Einheit (Leiterbahnseite) A 1 2 3 4 137 5 6 XV-Z9000U/E H G F E D C B PC I/F Unit (Component Side) PC-I/F-einheit (Bestückungsseite) A 1 2 3 4 138 5 6 XV-Z9000U/E H G F E D C B PC I/F Unit (Wiring Side) PC-I/F-einheit (Leiterbahnseite) A 1 2 3 4 139 5 6 XV-Z9000U/E Ref. No. ★ Part No. Description PARTS LIST Code Ref. No. ★ Part No. Description Code ERSATZTEILLISTE PARTS REPLACEMENT AUSTAUSCH VON TEILEN Parts marked with "å" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. Ersatzteile, die besondere Sicherheitseigenschften haben, sind in dieser Anleitung markiert. Elektrische Komponenten mit solchen Eigenshaften sind in den Ersatzteil durch "å" gekenn-zeichnet. Der Gebrauch von Ersatzteilen, die nicht deselben Sicherheitseigenschaften haben wie die vom Hersteller empfohlenen ud in der Bedienungsanleitung angegebenen, können zur Ursache von Blitzeinschlägen, Bränden und anderen Gefahren werden. "HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. "WIE MAN ERSATSTEILE BESTELLT" in USA: 1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRIPTION 5. CODE 6. QUANTITY Damit Ihre Bestellung promt und korrekt ausgeführt wird, geben Sie bitte folgende Informationen. 1. MODELL NR. 3. ERSATZTEIL NR. 5. KODE Contact your nearest SHARP Parts Distributor. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP 2. REF. NR. 4. BESCHREIBUNG 6. QUANTITÄT in CANADA: Contact SHARP Electronics of Canada Limited Phone (416) 890-2100. ★ MARK: SPARE PARTS-DELIVERY SECTION Ref. No. ★ Part No. Description ★ MARKIERUNG : ERSATZTEILE-LIEFERUNG Code Ref. No. ★ Part No. Description PRINTED WIRING BOARD ASSEMBLIES DUNTKA471DE02/03 (NOT REPLACEMENT ITEM) MAIN UNIT INTEGRATED CIRCUITS XV-Z9000U DUNTKA471DE02 DUNTKA472DE02 DUNTKA473DE02 DUNTKA474DE02 DUNTKA475DE02 RDENC0329CEZZ CPCi-0051CE01 RDENC0330CEZZ RUNTK0705CEZZ J Main Unit Key Unit R/C Front Unit R/C Rear Unit LED Unit Power Unit PC I/F Unit Ballast Unit (Unit Replacement Item) J Formatter Unit (Unit Replacement Item) IC2001 IC2002 IC2003 IC2004 IC2005 IC2006 IC2007 IC2501 IC2505 IC2506 IC2507 IC2508 IC2509 IC2510 IC2511 IC2512 IC2513 IC2514 IC2515 IC2805 IC2806 IC2807 IC2808 IC2809 IC2810 IC2811 IC2812 IC2814 IC2815 IC2816 IC2817 IC2818 IC3501 IC3504 IC3505 IC3506 IC3507 IC3580 — — — — — — — CC FM XV-Z9000E DUNTKA471DE03 DUNTKA472DE03 DUNTKA473DE03 DUNTKA474DE03 DUNTKA475DE03 RDENC0329CEZZ CPCi-0051CE02 RDENC0330CEZZ RUNTK0705CEZZ J Main Unit Key Unit R/C Front Unit R/C Rear Unit LED Unit Power Unit PC I/F Unit Ballast Unit (Unit Replacement Item) J Formatter Unit (Unit Replacement Item) Code — — — — — — — CC FM VHiMAX3224E-1 VHiS814A33M-1Y VHiSN2G53CT-1 VHiSN2G32CT-1 RH-iX3527CEN1Q VHiPST600iM-1 VHiS24C02A/-1 VHiLV4053AT-1 VHiMM1519XQ-1 VHiLV4053AT-1 VHiM52055FP-1 VHiTL712CPS-1 VHiLV125AT+-1 VHiNJM2903V-1 VHiTL712CPS-1 VHiTL712CPS-1 VHiTL712CPS-1 VHiTHC4538T-1 VHiT7SET08U-1 VHiPQ09DZ1U-1Y VHiPQ30RV31-2 VHiPQ05DZ1U-1Y VHiPQ20VB1E-1 VHiPQ3DZ13U-1Y VHiPQ070XH2-1Y VHiT7SET08U-1 VHiT7SET08U-1 VHiT7SET08U-1 VHiT7SET08U-1 VHiT7SET08U-1 VHiPQ05VY3H-1Y VHiPQ20VZ11-1 VHiTK15420/-1 VHiPD64082/-1 RH-iX3420CEZZ VHiPST600iM-1 VHiM52055FP-1 VHiPQ05TZ11-1 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J MAX3224ECAP S-814A33AMC-BC SN74AHC2G53HDC SN74AHC2G32HDC M30620FCMGP IC-PST600IMT S-24C02AFJ-TB SN74LV4053APWR MM1519XG SN74LV4053APWR M52055FP Tl712CPS SN74LV125APWR NJM2903V Tl712CPS Tl712CPS Tl712CPS TC74HC4538AFT TC7SET08FU PQ09DZ1U PQ30RV31 PQ05DZ1U PQ20VB1E PQ3DZ13U PQ070XH02ZP TC7SET08FU TC7SET08FU TC7SET08FU TC7SET08FU TC7SET08FU PQ05VY3H3ZP PQ20VZ11 TK15420MTl UPD64082GF-3BA MSM5416258B-28 IC-PST600IMT M52055FP PQ05TZ11 AU AE AE AE BD AE AK AE AW AE AH AL AE AD AL AL AL AL AE AG AL AG AH AG AG AE AE AE AE AE AK AH AG BC AT AE AH AH TRANSISTORS Q2001 VSHN2A01FU/-1 140 J HN2A01FU AC XV-Z9000U/E Ref. No. ★ Part No. Description Code DUNTKA471DE02/03 D2514 D2515 D2516 D2519 D2520 D2522 D2523 D2524 D2525 D2802 D2805 D2806 D2807 D2808 D2809 D2811 D2812 D2813 D2814 D2816 D2817 D2818 D2819 D2820 D2821 D2822 D2823 D2825 D2830 D2831 D2832 D2833 D2834 D2835 D2837 D2838 D2839 D3580 MAIN UNIT(Continued) Q2002 Q2004 Q2013 Q2015 Q2503 Q2504 Q2505 Q2509 Q2510 Q2511 Q2512 Q2513 Q2514 Q2515 Q2516 Q2517 Q2518 Q2519 Q2520 Q2522 Q2523 Q2524 Q2525 Q2526 Q2527 Q2528 Q2529 Q2530 Q2531 Q2802 Q2810 Q2811 Q2813 Q2815 Q2816 Q2817 Q2819 Q2820 Q2821 Q2822 Q2823 Q2824 Q2825 Q3502 Q3503 Q3504 Q3505 Q3506 Q3507 Q3508 Q3509 Q3510 Q3511 Q3512 Q3513 Q3514 Q3515 Q3516 VSRN4982///-1 VSRN4904///-1 VSDTC144EUA-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SC3928AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SC3928AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VSDTC144EUA-1 VS2SA1530AR-1 VSDTC144EUA-1 VSDTC144EUA-1 VS2SC3928AR-1 VS2SC3928AR-1 VSDTC144EUA-1 VSDTC144EUA-1 VSDTC144EUA-1 VSDTC144EUA-1 VS2SB1302S/-1 VS2SC3928AR-1 VS2SB1302S/-1 VS2SC3928AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SC3928AR-1 VS2SA1530AR-1 VS2SC3928AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SA1530AR-1 D2022 D2024 D2025 D2501 D2502 D2503 D2508 D2509 D2510 D2511 D2513 VHDHSU119//-1 RH-EX1230CEZZ RH-EX1262CEZZ VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J RN4982 RN4904 DTC144EUA 2SC3928AR 2SC3928AR 2SC3928AR 2SC3928AR 2SA1530AR 2SA1530AR 2SA1530AR 2SC3928AR 2SC3928AR 2SC3928AR 2SC3928AR 2SC3928AR 2SC3928AR 2SA1530AR 2SA1530AR 2SA1530AR 2SC3928AR 2SA1530AR 2SA1530AR 2SA1530AR 2SC3928AR 2SA1530AR 2SA1530AR 2SC3928AR 2SC3928AR 2SC3928AR DTC144EUA 2SA1530AR DTC144EUA DTC144EUA 2SC3928AR 2SC3928AR DTC144EUA DTC144EUA DTC144EUA DTC144EUA 2SB1302S 2SC3928AR 2SB1302S 2SC3928AR 2SA1530AR 2SA1530AR 2SA1530AR 2SA1530AR 2SA1530AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR 2SA1530AR 2SA1530AR 2SA1530AR 2SA1530AR 2SA1530AR 2SA1530AR AC AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AD AB AD AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB Diode Zener Diode (3.0V) Zener Diode (9.1V) Diode Diode Diode Diode Diode Diode Diode Diode Part No. VHDKDS226//-1Y VHDKDS226//-1Y RH-EX1264CEZZ RH-EX1264CEZZ RH-EX1264CEZZ VHDHSU119//-1 VHDKDS226//-1Y VHDHSU119//-1 VHDKDS226//-1Y VHDDAN202K/-1 RH-EX1271CEZZ RH-EX1271CEZZ RH-EX1271CEZZ RH-EX1271CEZZ VHDDAN202K/-1 RH-EX1271CEZZ RH-EX1247CEZZY RH-EX1271CEZZ RH-EX1247CEZZY VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDSC8024//-1 VHDHSU119//-1 VHDSC8024//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 VHDHSU119//-1 ★ Description J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Diode Diode Zener Diode (9V) Zener Diode (9V) Zener Diode (9V) Diode Diode Diode Diode Diode Zener Diode (12V) Zener Diode (12V) Zener Diode (12V) Zener Diode (12V) Diode Zener Diode (12V) Zener Diode (5.6V) Zener Diode (12V) Zener Diode (5.6V) Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Code AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AC AB AC AB AB AB AB AB AB PACKAGED CIRCUITS X2001 RCRSB0286CEZZ X3501 RCRSB0258CEZZ J Crystal (7.3728MHz) J Crystal (20MHz) AH AG FILTERS AND COILS FL2501 FL2502 FL2503 FL2504 FL2508 FL2510 FL2512 FL2513 FL2515 FL3503 FL3504 FL3508 FL3509 L2501 L2503 L2504 L2505 L2506 L2507 L2508 L2801 L2802 L3501 L3502 L3503 L3504 DIODES J J J J J J J J J J J Ref. No. AB AB AB AB AB AB AB AB AB AB AB RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0017TAZZ RFiLN0017TAZZ RFiLN0017TAZZ RCiLV0108GEZZ RCiLF0306CEZZ RCiLF0306CEZZ RCiLF0306CEZZ VP-NM680K3R5N VPAWM3R3J1R4N VPAWM220J4R0N VPAWM3R3J1R4N VPAWM220J4R0N VPAWM3R3J1R4N VPAWM220J4R0N RCiLP0303TAZZ RCiLP0303TAZZ VPAWM220J4R0N VPAWM220J4R0N VPAWM100J2R6N VPAWM4R7J1R7N J J J J J J J J J J J J J J J J J J J J J J J J J J Filter Filter Filter Filter Filter Filter Filter Filter Filter Filter Filter Filter Filter Peaking 68µH Peaking 3.3µH Peaking 22µH Peaking 3.3µH Peaking 22µH Peaking 3.3µH Peaking 22µH Peaking 220µH Peaking 220µH Peaking 22µH Peaking 22µH Peaking 10µH Peaking 4.7µH AD AD AD AD AD AD AC AC AC AG AH AH AH AB AC AC AC AC AC AC AG AG AC AC AC AC CAPACITORS C2002 VCKYTV1CB224K C2003 VCEAPF0JW107M C2005 VCKYTV1CB105K 141 J 0.22 J 100 J 1.0 16V Ceramic 6.3V Electrolytic 16V Ceramic AB AC AC XV-Z9000U/E Ref. No. Part No. ★ Description Code Ref. No. AA AC AC AD AC AA AB AA AA AA AB AB AA AA AC AA AA AA AA AB AA AB AB AB AB AA AC AC AC AC AC AB AA AA AB AB AA AA AA AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AC AC AC AC AC AC AA AD AD AD AD AD AD AD AD C2584 C2585 C2586 C2587 C2588 C2589 C2590 C2591 C2592 C2593 C2594 C2595 C2596 C2597 C2598 C2599 C2600 C2601 C2602 C2603 C2604 C2605 C2606 C2607 C2803 C2805 C2812 C2815 C2818 C2822 C2823 C2824 C2825 C2826 C2827 C2828 C2829 C2830 C2832 C2833 C2834 C2835 C2836 C2837 C2838 C2839 C2840 C2841 C2842 C2843 C2844 C2846 C2849 C2852 C2854 C2856 C2857 C2859 C2860 C2861 C2862 C2869 C2870 C2871 C2872 C2873 C2874 C2875 C2876 C2877 C2878 C2879 C2880 C3505 C3506 DUNTKA471DE02/03 MAIN UNIT(Continued) C2006 C2008 C2010 C2012 C2014 C2015 C2016 C2017 C2018 C2019 C2020 C2021 C2022 C2023 C2024 C2027 C2028 C2029 C2501 C2505 C2506 C2507 C2508 C2509 C2510 C2513 C2517 C2518 C2519 C2520 C2521 C2526 C2528 C2529 C2530 C2531 C2537 C2538 C2539 C2543 C2544 C2546 C2548 C2550 C2551 C2552 C2553 C2554 C2555 C2556 C2557 C2558 C2559 C2560 C2561 C2562 C2563 C2564 C2565 C2566 C2567 C2568 C2570 C2572 C2573 C2574 C2576 C2577 C2578 C2582 C2583 VCKYCY1EF104Z VCKYTV1CB105K VCKYTV1CB105K VCEAPF1CW107M VCEAPF0JW107M VCKYCY1EF104Z VCCCCY1EH102J VCKYCY1EF104Z VCCCCY1HH220J VCCCCY1HH220J VCKYCY1CB104K VCKYCY1CB104K VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF0JW107M VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1EF104Z VCEAPF1CW106M VCKYCY1HB103K VCEAPF1CW106M VCEAPF1HW105M VCEAPF1HW105M VCEAPF1HW105M VCKYCY1HB103K VCKYTV1CB105K VCKYTV1CB105K VCKYTV1CB105K VCKYTV1CB105K VCKYTV1CB105K VCEAPF1HW105M VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF1HW105M VCEAPF1HW105M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF1CW107M VCKYCY1EF104Z VCCCCY1HH120J VCCCCY1HH120J VCCCCY1HH3R0C VCCCCY1HH5R0C VCCCCY1HH3R0C VCCCCY1HH5R0C VCCCCY1HH3R0C VCCCCY1HH5R0C VCCCCY1HH270J VCCCCY1HH7R0D VCCCCY1HH270J VCCCCY1HH7R0D VCCCCY1HH270J VCCCCY1HH7R0D VCE9PF1CW106M VCE9PF1CW106M VCE9PF1CW106M VCE9PF1CW106M VCE9PF1CW106M VCE9PF1CW106M VCEAPF1CW476M VCCCCY1HH120J VCEAPF0JW227MY VCEAPF0JW227MY VCEAPF0JW227MY VCEAPF0JW227MY VCEAPF0JW227MY VCEAPF0JW227MY VCEAPF0JW227MY VCEAPF0JW227MY J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.1 1.0 1.0 100 100 0.1 1000p 0.1 22p 22p 0.1 0.1 0.1 0.1 100 0.01 0.01 0.01 0.1 10 0.01 10 1.0 1.0 1.0 0.01 1.0 1.0 1.0 1.0 1.0 1.0 0.1 0.1 1.0 1.0 0.1 0.1 0.1 100 0.1 12p 12p 3.0p 5.0p 3.0p 5.0p 3.0p 5.0p 27p 7.0p 27p 7.0p 27p 7.0p 10 10 10 10 10 10 47 12p 220 220 220 220 220 220 220 220 25V 16V 16V 16V 6.3V 25V 25V 25V 50V 50V 16V 16V 25V 25V 6.3V 50V 50V 50V 25V 16V 50V 16V 50V 50V 50V 50V 16V 16V 16V 16V 16V 50V 25V 25V 50V 50V 25V 25V 25V 16V 25V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 16V 16V 16V 16V 16V 16V 50V 6.3V 6.3V 6.3V 6.3V 6.3V 6.3V 6.3V 6.3V Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Elect.(N.P) Elect.(N.P) Elect.(N.P) Elect.(N.P) Elect.(N.P) Elect.(N.P) Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic 142 Part No. VCEAPF0JW227MY VCEAPF0JW227MY VCEAPF0JW227MY VCEAPF0JW227MY VCCCCY1HH330J VCEAPF0JW226M VCE9PF1CW106M VCKYCY1EF104Z VCKYCY1EF104Z VCE9PF1CW106M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCCCCY1HH330J VCE9PF1CW106M VCE9PF1CW106M VCKYCY1EF104Z VCKYCY1HB472K VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCCCCY1HH101J VCCCCY1HH101J VCKYCY1CB104K VCKYCY1CB104K VCEAPF1CW226M VCEAPF1CW107M VCEAPF1CW107M VCEAPF1CW107M VCKYTV1EB104K VCEAPF1EW336M VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF1CN107M VCKYTV1EB104K VCEAPF1CN107M VCKYTV1EB104K VCEAPF0JW227MY VCEAPF1CW106M VCEAPF1CN107M VCEAPF1EW336M VCKYCY1CB104K VCKYCY1EF104Z VCEAPF1CW107M VCKYCY1CB104K VCEAPF0JW336M VCEAPF0JW227MY VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1CB104K VCKYCY1CB104K VCKYCY1EF104Z VCEAPF1CN107M VCEAPF1CW107M VCEAPF1CW107M VCEAPX1CW477M VCEAPX1CW477M VCKYCY1EF104Z VCKYCY1EF104Z VCAAPC0JJ336M VCEAPF0JW107M VCEAPF0JW107M VCKYCY1EF104Z VCEAPF1CW107M VCKYCY1EF104Z VCEAPF1CW107M VCEAPF1HW475M VCEAPF1HW475M VCAAPC0GJ336M VCKYCY1EF104Z VCKYCY1HB103K ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 220 220 220 220 33p 22 10 0.1 0.1 10 0.1 0.1 0.1 33p 10 10 0.1 4700p 0.1 0.1 0.1 0.1 0.1 0.1 100p 100p 0.1 0.1 22 100 100 100 0.1 33 0.1 0.1 100 0.1 100 0.1 220 10 100 33 0.1 0.1 100 0.1 33 220 0.1 0.1 0.1 0.1 0.1 0.1 100 100 100 470 470 0.1 0.1 33 100 100 0.1 100 0.1 100 4.7 4.7 33 0.1 0.01 6.3V 6.3V 6.3V 6.3V 50V 6.3V 16V 25V 25V 16V 25V 25V 25V 50V 16V 16V 25V 50V 25V 25V 25V 25V 25V 25V 50V 50V 16V 16V 16V 16V 16V 16V 25V 25V 25V 25V 16V 25V 16V 25V 6.3V 16V 16V 25V 16V 25V 16V 16V 6.3V 6.3V 25V 25V 25V 16V 16V 25V 16V 16V 16V 16V 16V 25V 25V 6.3V 6.3V 6.3V 25V 16V 25V 16V 50V 50V 4V 25V 50V Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Elect.(N.P) Ceramic Ceramic Elect.(N.P) Ceramic Ceramic Ceramic Ceramic Elect.(N.P) Elect.(N.P) Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Code AD AD AD AD AA AB AC AA AA AC AA AA AA AA AC AC AA AA AA AA AA AA AA AA AA AA AB AB AB AD AD AD AB AB AA AA AD AB AD AB AD AB AD AB AB AA AD AB AB AD AA AA AA AB AB AA AD AD AD AE AE AA AA AC AC AA AD AA AD AB AB AA AA XV-Z9000U/E Ref. No. ★ Part No. Description Code DUNTKA471DE02/03 MAIN UNIT(Continued) C3507 C3508 C3510 C3511 C3512 C3513 C3514 C3515 C3516 C3517 C3518 C3520 C3521 C3522 C3523 C3524 C3525 C3526 C3527 C3528 C3529 C3530 C3531 C3532 C3533 C3534 C3535 C3536 C3537 C3538 C3539 C3540 C3541 C3543 C3545 C3546 C3547 C3548 C3549 C3550 C3551 C3552 C3553 C3554 C3555 C3556 C3557 C3558 C3559 C3563 C3565 C3567 C3570 C3571 C3572 C3573 C3574 C3575 C3576 C3577 C3580 C3581 C3582 C3583 VCCCCY1HH120J VCCCCY1HH100D VCCCCY1HH6R0D VCCCCY1HH120J VCCCCY1HH270J VCCCCY1HH270J VCEAPF1CW106M VCCCCY1HH270J VCEAPF0JW226M VCCCCY1HH270J VCKYCY1HB103K VCEAPF0JW107M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF1HW105M VCEAPF0JW226M VCEAPF0JW226M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF1CW106M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF1HW105M VCCCCY1HH471J VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF1HW474M VCKYCY1HB102K VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCCCCY1HH270J VCCCCY1HH220J VCEAPF0JW226M VCKYCY1EF104Z VCCCCY1HH391J VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF1CW106M VCEAPF1CW107M VCKYCY1EF104Z VCEAPF0JW227MY VCEAPF0JW227MY VCKYCY1EF104Z VCEAPF0JW227MY VCEAPF0JW227MY VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF1CW476M VCKYCY1EF104Z VCEAPF0JW107M VCKYCY1EF104Z R2010 R2011 R2012 R2013 R2018 VRS-TV1JD3R9J VRS-CY1JF473J VRS-CY1JF103J VRS-CY1JF154J VRS-CY1JF153J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 12p 10p 6.0p 12p 27p 27p 10 27p 22 27p 0.01 100 0.1 0.1 0.1 1.0 22 22 0.1 0.1 0.1 10 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 1.0 470p 0.1 0.1 0.47 1000p 0.1 0.1 0.1 0.1 0.1 0.1 27p 22p 22 0.1 390p 0.1 0.1 10 100 0.1 220 220 0.1 220 220 0.1 0.1 47 0.1 100 0.1 50V 50V 50V 50V 50V 50V 16V 50V 6.3V 50V 50V 6.3V 25V 25V 25V 50V 6.3V 6.3V 25V 25V 25V 16V 25V 25V 25V 25V 25V 25V 25V 25V 25V 50V 50V 25V 25V 50V 50V 25V 25V 25V 25V 25V 25V 50V 50V 6.3V 25V 50V 25V 25V 16V 16V 25V 6.3V 6.3V 25V 6.3V 6.3V 25V 25V 16V 25V 6.3V 25V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic AA AA AA AA AA AA AB AA AB AA AA AC AA AA AA AB AB AB AA AA AA AB AA AA AA AA AA AA AA AA AA AB AA AA AA AB AA AA AA AA AA AA AA AA AA AB AA AA AA AA AB AD AA AD AD AA AD AD AA AA AC AA AC AA 1/10W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide AA AA AA AA AA RESISTORS J J J J J 3.9 47k 10k 150k 15k 143 Ref. No. Part No. ★ R2025 R2027 R2028 R2029 R2031 R2038 R2039 R2040 R2041 R2043 R2047 R2049 R2050 R2051 R2053 R2054 R2056 R2057 R2058 R2060 R2061 R2066 R2067 R2068 R2070 R2071 R2072 R2073 R2074 R2075 R2076 R2078 R2079 R2080 R2501 R2502 R2503 R2504 R2505 R2506 R2507 R2512 R2513 R2521 R2522 R2523 R2531 R2533 R2535 R2536 R2537 R2538 R2539 R2540 R2541 R2542 R2555 R2556 R2557 R2559 R2571 R2572 R2575 R2576 R2577 R2579 R2580 R2581 R2582 R2585 R2588 R2592 R2593 R2594 R2595 VRS-CB1JF101J VRS-CA1JF101J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF103J VRS-CB1JF101J VRS-CY1JF682J VRS-CB1JF103J VRS-CB1JF101J VRS-CY1JF333J VRS-CA1JF101J VRS-CB1JF101J VRS-CB1JF101J VRS-CB1JF100J VRS-CB1JF101J VRS-CB1JF100J VRS-CY1JF471J VRS-CY1JF100J VRS-CY1JF104J VRS-CA1JF151JY VRS-CY1JF103J VRS-CB1JF100J VRS-CA1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CB1JF103J VRS-CA1JF103J VRS-CB1JF103J VRS-CY1JF473J VRS-CB1JF102J VRS-CY1JF103J VRS-CB1JF823J VRS-CY1JF102J VRS-CY1JF103J VRS-TW2ED750J VRS-TW2ED750J VRS-CY1JF102J VRS-CY1JF102J VRS-TW2ED750J VRS-CY1JF102J VRS-CY1JF102J VRS-TW2ED750J VRS-TW2ED750J VRS-TW2ED750J VRS-TW2ED750J VRS-TW2ED750J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF220J VRS-CY1JF220J VRS-CY1JF220J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF220J VRS-CY1JF103J VRS-CY1JF220J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF220J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 100 100 10 10 10k 100 6.8k 10k 100 33k 100 100 100 10 100 10 470 10 100k 150 10k 10 100 100 100 10k 10k 10k 47k 1.0k 10k 82k 1.0k 10k 75 75 1.0k 1.0k 75 1.0k 1.0k 75 75 75 75 75 100 100 100 22 22 22 100 100 1.0k 1.0k 100 100 100 1.0k 100 100 22 10k 22 10k 10k 10k 22 10k 10k 10k 10k 10k 10k 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA XV-Z9000U/E Ref. No. Part No. ★ Description Code Ref. No. AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA R2692 R2693 R2697 R2700 R2703 R2704 R2705 R2706 R2707 R2708 R2709 R2710 R2711 R2712 R2713 R2714 R2715 R2717 R2718 R2719 R2803 R2804 R2805 R2806 R2807 R2808 R2809 R2817 R2818 R2819 R2821 R2822 R2825 R2832 R2847 R2849 R2850 R2851 R2853 R2854 R2855 R2856 R2857 R2860 R2862 R2864 R2865 R2866 R2869 R2870 R2873 R2875 R2876 R2877 R2878 R2879 R2881 R2882 R2883 R2886 R2887 R2891 R2893 R2894 R2896 R2897 R2898 R2904 R2910 R2911 R2912 R2913 R2915 R2916 R2917 DUNTKA471DE02/03 MAIN UNIT(Continued) R2599 R2603 R2615 R2616 R2617 R2618 R2619 R2620 R2621 R2622 R2623 R2624 R2625 R2626 R2627 R2628 R2629 R2630 R2631 R2632 R2633 R2634 R2635 R2636 R2637 R2638 R2639 R2640 R2641 R2642 R2643 R2644 R2646 R2647 R2649 R2650 R2652 R2653 R2654 R2655 R2656 R2657 R2658 R2662 R2663 R2664 R2665 R2666 R2668 R2669 R2670 R2671 R2672 R2673 R2674 R2675 R2676 R2677 R2678 R2679 R2680 R2681 R2682 R2683 R2684 R2685 R2686 R2687 R2689 R2690 R2691 VRS-CY1JF103J VRS-CY1JF103J VRS-TW2ED750J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF472J VRS-CY1JF472J VRS-CY1JF472J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF911J VRS-CY1JF681J VRS-CY1JF911J VRS-CY1JF681J VRS-CY1JF911J VRS-CY1JF681J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-TW2ED391J VRS-CY1JF620J VRS-TW2ED391J VRS-CY1JF620J VRS-TW2ED391J VRS-CY1JF620J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-TW2ED391J VRS-TW2ED391J VRS-TW2ED391J VRS-CY1JF620J VRS-CY1JF620J VRS-CY1JF620J VRS-CY1JF102J VRS-CY1JF271J VRS-CY1JF103J VRS-CY1JF330J VRS-CY1JF392J VRS-CY1JF183J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF333J VRS-CY1JF183J VRS-CY1JF472J VRS-CY1JF391J VRS-CY1JF391J VRS-CY1JF153J VRS-CY1JF222J VRS-CY1JF104J VRS-CY1JF222J VRS-CY1JF391J VRS-CY1JF222J VRS-CY1JF391J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF271J VRS-CY1JF102J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10k 10k 75 100 100 4.7k 4.7k 4.7k 1.0k 1.0k 1.0k 910 680 910 680 910 680 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 100 1.0k 1.0k 1.0k 100 100 100 100 390 62 390 62 390 62 100 100 100 390 390 390 62 62 62 1.0k 270 10k 33 3.9k 18k 4.7k 10k 33k 18k 4.7k 390 390 15k 2.2k 100k 2.2k 390 2.2k 390 1.0k 1.0k 1.0k 270 1.0k 1/16W 1/16W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/16W 1/4W 1/16W 1/4W 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide 144 Part No. VRS-CY1JF104J VRS-CY1JF104J VRS-CY1JF153J VRS-CY1JF103J VRS-CY1JF333J VRS-CY1JF330J VRS-CY1JF392J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF330J VRS-CY1JF330J VRS-CY1JF473J VRS-CY1JF392J VRS-CY1JF392J VRS-CY1JF222J VRS-CY1JF222J VRS-CY1JF222J VRS-CY1JF103J VRS-CY1JF103J VRS-CB1JF000J VRS-CY1JF472J VRS-CY1JF182J VRS-CY1JF472J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF472J VRS-CY1JF472J VRN-CY1JF153D VRS-CY1JF102J VRS-CY1JF102J VRN-CY1JF153D VRS-CY1JF472J VRS-CY1JF392J VRS-TX2HF120J VRS-TX2HF120J VRS-TX2HF1R0J VRS-TX2HF5R6J VRS-TW2ED1R2JY VRS-TW2ED1R2JY VRS-TX2HF1R0J VRS-TX2HF5R6J VRS-TX2HF000J VRS-CY1JF101J VRS-CY1JF103J VRN-CY1JF274DY VRN-CY1JF114DY VRN-CY1JF562D VRN-CY1JF912D VRS-CY1JF103J VRN-CY1JF681D VRN-CY1JF120DY VRS-CY1JF103J VRS-CY1JF103J VRS-TW2ED2R2J VRS-TV1JD222J VRS-TV1JD3R9J VRS-TW2ED2R2J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF102J VRS-TV1JD272J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF000J VRN-CY1JF132D VRN-CY1JF392D VRS-CY1JF103J VRS-CY1JF000J VRS-TX2HF821JY VRS-TX2HF821JY VRS-CY1JF181J ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 100k 100k 15k 10k 33k 33 3.9k 10k 10k 33 33 47k 3.9k 3.9k 2.2k 2.2k 2.2k 10k 10k 0 4.7k 1.8k 4.7k 100 100 1.0k 1.0k 4.7k 4.7k 15k 1.0k 1.0k 15k 4.7k 3.9k 12 12 1.0 5.6 1.2 1.2 1.0 5.6 0 100 10k 270k 110k 5.6k 9.1k 10k 680 12 10k 10k 2.2 2.2k 3.9 2.2 4.7k 10k 1.0k 2.7k 10k 10k 10k 1.0k 0 1.3k 3.9k 10k 0 820 820 180 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W MetalFilm 1/16W Metal Oxide 1/16W Metal Oxide 1/16W MetalFilm 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W MetalFilm 1/16W MetalFilm 1/16W MetalFilm 1/16W MetalFilm 1/16W Metal Oxide 1/16W MetalFilm 1/16W MetalFilm 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/10W Metal Oxide 1/10W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W MetalFilm 1/16W MetalFilm 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AB AA AA AB AA AA AA AB AA AA AB AA AA AA AA AA AA AA AA AA AB AA AA AA AB AB AA XV-Z9000U/E Ref. No. Part No. ★ Description Code DUNTKA471DE02/03 MAIN UNIT(Continued) R2918 R2919 R2920 R2924 R2926 R2927 R2928 R2929 R2930 R2931 R2932 R2933 R2935 R2936 R3502 R3503 R3504 R3505 R3506 R3507 R3508 R3509 R3510 R3511 R3512 R3513 R3514 R3515 R3517 R3518 R3519 R3520 R3521 R3522 R3523 R3524 R3525 R3526 R3527 R3528 R3529 R3530 R3531 R3532 R3533 R3534 R3535 R3536 R3537 R3538 R3539 R3540 R3541 R3543 R3546 R3547 R3548 R3549 R3561 R3563 R3564 R3570 R3572 R3573 R3575 R3577 R3580 R3581 R3582 R3586 R3587 VRS-CY1JF181J VRS-CY1JF000J VRS-CY1JF000J VRS-TX2HF2R2J VRN-CY1JF202D VRN-CY1JF222D VRN-CY1JF750DY VRS-TX2HF1R0J VRN-CY1JF512D VRN-CY1JF301D VRN-CY1JF102D VRS-CY1JF103J VRS-CY1JF123J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF471J VRS-CY1JF152J VRS-CY1JF431J VRS-CY1JF102J VRS-CY1JF471J VRS-CY1JF332J VRS-CY1JF561J VRS-CY1JF182J VRS-CY1JF202J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF821J VRS-CY1JF911J VRS-CY1JF392J VRS-CY1JF202J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF391J VRS-CY1JF181J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF100J VRS-CY1JF100J VRS-TX2HF2R2J VRS-TV1JD2R2J VRS-CY1JF000J VRS-CY1JF221J VRS-CY1JF000J VRS-CY1JF473J VRS-CY1JF224J VRS-CY1JF102J VRS-CY1JF222J VRS-CY1JF471J VRS-CY1JF472J VRS-CY1JF182J VRS-CY1JF182J VRS-CA1JF101J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF471J VRS-CY1JF471J VRS-CY1JF101J VRS-CY1JF104J VRS-CY1JF104J VRS-TW2ED391J VRS-CY1JF104J VRS-CY1JF104J VRS-TW2ED391J VRS-TW2ED391J VRS-TX2HF1R0J VRS-TX2HF1R0J VRS-CY1JF103J VRS-CY1JF620J VRS-CY1JF750J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 180 0 0 2.2 2.0k 2.2k 75 1.0 5.1k 300 1.0k 10k 12k 1.0k 100 470 1.5k 430 1.0k 470 3.3k 560 1.8k 2.0k 1.0k 1.0k 820 910 3.9k 2.0k 1.0k 1.0k 1.0k 390 180 1.0k 1.0k 10 10 2.2 2.2 0 220 0 47k 220k 1.0k 2.2k 470 4.7k 1.8k 1.8k 100 1.0k 0 0 470 470 100 100k 100k 390 100k 100k 390 390 1.0 1.0 10k 62 75 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W MetalFilm 1/16W MetalFilm 1/16W MetalFilm 1/2W Metal Oxide 1/16W MetalFilm 1/16W MetalFilm 1/16W MetalFilm 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/10W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide AA AA AA AB AB AB AA AA AC AC AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA Ref. No. Part No. ★ R3588 R3589 R3590 R3591 R3592 R3593 R3594 R3595 R3596 R3597 VRS-CY1JF620J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF391J VRS-CY1JF392J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF391J VRS-CY1JF392J J J J J J J J J J J FB2003 FB2004 FB2005 FB2501 FB2502 FB2503 FB2504 FB2516 FB2517 FB2801 FB2802 FB2803 FB2804 FB2805 FB2809 FB2811 FB2812 FB2813 FB2814 FB2815 FB2816 FB2817 FB2818 FB2819 FB2820 FB2821 FB2822 FB2823 FB2824 FB2825 FB2828 FB2829 FB2830 FB2831 FB2833 FB2834 FB2835 FB2836 FB2837 FB2841 FB2843 FB2844 FB2845 FB2846 FB2847 FB2848 FB2849 FB2850 FB3501 FB3502 FB3507 J2501 J2501 J2503 J2503 J2505 J2801 J2802 P2001 P2801 P2802 P2804 P2805 RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0060TAZZ RBLN-0060TAZZ RBLN-0060TAZZ RBLN-0060TAZZ RBLN-0061TAZZ RBLN-0061TAZZ RBLN-0059CEZZ RBLN-0064TAZZ RBLN-0064TAZZ RBLN-0064TAZZ RBLN-0064TAZZ RBLN-0058TAZZ RBLN-0058TAZZ RBLN-0058TAZZ RBLN-0059CEZZ RBLN-0064TAZZ RBLN-0064TAZZ RBLN-0064TAZZ RBLN-0064TAZZ RBLN-0064TAZZ RBLN-0064TAZZ RBLN-0064TAZZ RBLN-0064TAZZ RBLN-0062CEZZ RBLN-0058TAZZ RBLN-0060TAZZ RBLN-0060TAZZ RBLN-0062CEZZ RBLN-0058TAZZ RBLN-0058TAZZ RBLN-0058TAZZ RBLN-0058TAZZ RBLN-0059CEZZ RBLN-0058TAZZ RBLN-0058TAZZ RBLN-0058TAZZ RBLN-0058TAZZ RBLN-0090CEZZ RBLN-0090CEZZ RBLN-0084CEZZ RBLN-0084CEZZ RBLN-0090CEZZ RBLN-0090CEZZ RBLN-0090CEZZ RBLN-0090CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0064TAZZ QJAKLA001WJZZ QJAKL0012CEZZ QJAKHA002WJZZ QJAKH0020CEZZ QJAKZ1053CEZZ QJAKA0022CEZZ QJAKE0071CEZZ QPLGN0063CEZZY QPLGN0539FJZZY QPLGN0539FJZZY QPLGN0176FJZZ QPLGN0541FJZZY Description 62 100 1.0k 390 3.9k 100 100 1.0k 390 3.9k 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide Code AA AA AA AA AA AA AA AA AA AA MISCELLANEOUS PARTS 145 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Jack (XV-Z9000U) Jack (XV-Z9000E) Jack (XV-Z9000U) Jack (XV-Z9000E) Jack Jack DC Jack Plug 13-Pin (KY) Plug 2-Pin (TA) Plug 2-Pin (TB) Plug 4-Pin (FA) Plug 4-Pin (FB) AB AB AB AB AB AB AB AD AD AB AC AC AC AC AC AC AC AB AC AC AC AC AC AC AC AC AC AC AB AB AC AC AC AC AC AB AC AC AC AC AD AD AD AD AD AD AD AD AB AB AC AN AM AM AL AG AC AD AF AD AD AD AD XV-Z9000U/E Ref. No. ★ Part No. Description Code Ref. No. ★ Part No. Description DUNTKA471DE02/03 DUNTKA473DE02/03 MAIN UNIT(Continued) R/C FRONT UNIT P2806 QPLGN0540FJZZY P2807 QPLGN0565FJZZY P2809 QPLGN0464TAZZ P2810 QPLGN0565FJZZY P2811 QPLGN0550FJZZY P2812 QPLGN0547FJZZY P2813 QPLGN0547FJZZY P3580 QCNCM6013CEZZ P3581 QCNCM6013CEZZ P3582 QCNCM6013CEZZ SC2801 QSOCN0437FJZZ SW2002QSW-K0065GEZZ RH-HZ0091CEZZ RH-HZ0092CEZZ LHLDW1047CEUZ J J J J J J J J J J J J J J J Plug 3-Pin (FC) Plug 4-Pin (FD) Plug 4-Pin (CA) Plug 3-Pin (RC) Plug 13-Pin (EA) Plug 10-Pin (EB) Plug 10-Pin (J2) Plug 60-Pin Plug 60-Pin Plug 60-Pin RS232C D-Sub Key Switch Thermister (TA:Red) Thermister (TB:White) Holder CAPACITORS AD AD AC AD AF AE AE AP AP AP AM AC AL AL AA C2401 VCKYCY1EF104Z C2403 VCEAPF0JW107M J 0.1 J 100 25V Ceramic 6.3V Electrolytic AA AC 1/16W Metal Oxide 1/16W Metal Oxide AA AA RESISTORS R2401 VRS-CY1JF471J R2402 VRS-CY1JF220J J 470 J 22 MISCELLANEOUS PARTS P2401 QPLGN0364TAZZ J RMC2401 RRMCU0239CEZZ J SLD2001 PSLDC3117CEFW J QCNW-5958CEZZ J LANGQ5725CEFW J LX-BZ3266CEFD J Plug 3-Pin (RC) R/C Receiver Sheild Connecting Cord (RC) Angl Screw DUNTKA472DE02/03 DUNTKA474DE02/03 KEY UNIT R/C REAR UNIT CAPACITOR C2202 VCKYCY1CB104K J 0.1 Code AC AG AD AG AF AA CAPACITORS 16V Ceramic AB C2404 VCKYCY1EF104Z C2406 VCEAPF0JW107M J 0.1 J 100 25V Ceramic 6.3V Electrolytic AA AC 1/16W Metal Oxide 1/16W Metal Oxide AA AA RESISTORS R2201 R2202 R2203 R2204 R2205 R2206 R2207 R2210 R2211 VRS-CY1JF562J VRS-CY1JF562J VRS-CY1JF562J VRS-CY1JF682J VRS-CY1JF682J VRS-CY1JF682J VRS-CY1JF223J VRS-CB1JF103J VRS-CB1JF102J J J J J J J J J J 5.6k 5.6k 5.6k 6.8k 6.8k 6.8k 22k 10k 1.0k 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide RESISTORS AA AA AA AA AA AA AA AA AA R2403 VRS-CY1JF471J R2404 VRS-CY1JF220J MISCELLANEOUS PARTS P2402 QPLGN0364TAZZ J RMC2402 RRMCU0237CEZZ J QCNW-5957CEZZ J LANGQ5726CEFW J LX-BZ3266CEFD J MISCELLANEOUS PARTS CN2202 QPLGN0063CEZZ P2814 QPLGN0364TAZZ P2815 QPLGN0964TAZZ SW2201QSW-K0065GEZZ SW2202QSW-K0065GEZZ SW2203QSW-K0065GEZZ SW2204QSW-K0065GEZZ SW2205QSW-K0065GEZZ SW2206QSW-K0065GEZZ SW2207QSW-K0065GEZZ SW2208QSW-K0065GEZZ SW2209QSW-K0065GEZZ SW2210QSW-K0065GEZZ SW2211 QSW-K0065GEZZ QCNW-5954CEZZ J J J J J J J J J J J J J J J Plug 13-Pin (KY) Plug 3-Pin (RA) Plug 9-Pin (RE) Key Switch Key Switch Key Switch Key Switch Key Switch Key Switch Key Switch Key Switch Key Switch Key Switch Key Switch Connecting Cord (KY) J 470 J 22 AC AF AC AC AC AC AC AC AC AC AC AC AC AL Plug 3-Pin (RA) R/C Receiver Connecting Cord (RA) Angl Screw AC AF AF AF AA DUNTKA475DE02/03 LED UNIT DIODES D2202 RH-PX0445CEZZY D2203 RH-PX0445CEZZY D2204 RH-PX0196TAZZ J LED RED & BLUE J LED RED & BLUE J LED RED AM AM AC CAPACITOR C2204 VCKYCY1CB104K J 0.1 16V Ceramic AB RESISTORS R2213 R2214 R2215 R2216 R2217 VRS-TV1JD182J VRS-TV1JD472J VRS-TV1JD102J VRS-TV1JD102J VRS-TV1JD472J J J J J J 1.8k 4.7k 1.0k 1.0k 4.7k 1/10W Metal Oxide 1/10W Metal Oxide 1/10W Metal Oxide 1/10W Metal Oxide 1/10W Metal Oxide AA AA AA AA AA MISCELLANEOUS PART P2450 QPLGN0571FJZZY J Plug 9-Pin (RE) QCNW-5955CEZZ J Connecting cord (RE) 146 AE XV-Z9000U/E Ref. No. ★ Part No. Description Code Ref. No. RDENC0329CEZZ PTC7001 95C0D802A1010 å TRA7001 95C0D513A6120 å Z7001 95C0D754A4710 INTEGRATED CIRCUITS 95CH1101AC001 95C0H1Q3A0010 95C0H1Q3A0010 95C0H132A0010 95C0H1Q3A0010 95C0H146A0010 95C0H141A0010 J J J J J J J FA5332M TA76431 TA76431 AN8021L TA76431 PQ1CG21H2FZ HA16114P BD TRANSISTORS Q7001 Q7002 Q7003 Q7004 Q7005 Q7006 Q7007 Q7101 Q7102 Q7103 Q7104 Q7105 Q7106 Q7107 Q7151 Q7201 Q7202 Q7401 Q7402 Q7403 95C0T252A0010 95C0T454A0010 95C0T196A0010 95C0T643A0010 95C0T643A0010 95C0T394A0010 95C0T192A0010 95C0T395A0020 95C0T645A0020 95C0T193A0010 95C0T394A0010 95C0T192A0010 95C0T394A0010 95C0T394A0010 95C0T397A0010 95C0T640A0010 95C0T192A0010 95C0T502A0010 95C0T394A0010 95C0T394A0010 å D7001 å D7002 å D7003 å D7004 å D7005 å D7006 å D7007 D7010 D7012 D7013 D7014 D7015 D7101 D7102 D7103 D7104 D7105 D7109 D7111 D7112 D7113 D7114 D7115 D7151 D7152 D7201 D7202 D7203 D7204 D7206 D7301 D7302 D7303 D7351 D7352 D7401 D7402 D7404 D7405 95C0D118A0060 95C0D157A0060 95C0D157A0060 95C0D157A0060 95C0D157A0060 95C0D157A0060 95C0D157A0060 95C0D2171AL06 95C0D491A0290 95C0D491A0290 95C0D491A0290 95C0D264A0020 95C0D491A0080 95C0D295A0080 95C0D295A0080 95C0D491A0190 95C0D295A0080 95C0D295A0080 95C0D492A0070 95C0D492A0020 95C0D295A0080 95C0D491A0190 95C0D292A0020 95C0D201A0020 95C0D265A0020 95C0D265A0020 95C0D267A0100 95C0D491A0290 95C0D491A0290 95C0D264A0020 95C0D222B0020 95C0D491A0290 95C0D295A0080 95C0D295A0080 95C0D219B0060 95C0D227B0040 95C0D227B0040 95C0D492A0050 95C0D295A0080 J J J J J J J J J J J J J J J J J J J J 2SB1237 2SD1858 2SA1812 2SK2698 2SK2698 2SC4081 2SA1576A 2SC4097 2SK2717 2SA1577 2SC4081 2SA1576A 2SC4081 2SC4081 2SC4672K 2SK2651-01MR 2SA1576A 2SJ303 2SC4081 2SC4081 AS AY AY AH AH AL AW AH AH AH AH AM AH AH AH DIODES J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Diode, D15XB60 Diode, ERA15-06 Diode, ERA15-06 Diode, ERA15-06 Diode, ERA15-06 Diode, ERA15-06 Diode, ERA15-06 Diode, YG963S6R Zener Diode, UDZ30B Zener Diode, UDZ30B Zener Diode, UDZ30B Diode, ERB44-02 Zener Diode, UDZ3.9B Diode, 1SS355 Diode, 1SS355 Zener Diode, UDZ11B Diode, 1SS355 Diode, 1SS355 Zener Diode, UDZS9.1B Zener Diode, UDZS5.6B Diode, 1SS355 Zener Diode, UDZS11B Diode, SC902-2 Diode, ERA92-02 Diode, ERA91-02 Diode, ERA91-02 Diode, ERA22-10 Zener Diode, UDZ30B Zener Diode, UDZ30B Diode, ERB44-02 Diode, YG902C2R Zener Diode, UDZ16B Diode, 1SS355 Diode, 1SS355 Diode, YG811S06R Diode, YG805C04R Diode, YG805C04R Zener Diode, UDZS7.5B Diode, 1SS355 Description Code PACKAGED CIRCUITS POWER UNIT å IC7001 IC7002 IC7151 å IC7201 IC7301 IC7351 IC7401 ★ Part No. AE AE AE AE AE AE AE AM AM AM AG AE AE AE AE AK AE AM AM AM AG AM AE AE AM AK AE J PTH9M04BD222TS2F333 J SM12JZ47 J ENC471 AP COILS AND TRANSFORMER å L7001 å L7002 å L7005 å L7006 L7007 L7008 L7351 L7352 L7401 T7001 å T7002 95C0L107R8020 95C0L107R8020 95C0L110K2230 95C0L114R1010 95C0L106R1020 95C0L309R0010 95C0L150S1000 95C0L124R1310 95C0L124R3000 95CL2000BS023 95CL2000US075 J J J J J J J J J J J Line Filter, FK-080G-8020R Line Filter, FK-080G-8020R Line Filter, PLA10A2230R4D02B1 Inductor, SK-12M-5YRP Inductor, HK-14D100-1020 Ferrite Bead, FK0B140RN02B Inductor, 8 18261A(10uH) Inductor, HK-08S060-1310 Inductor, HK-08S080-3000R Transformer, 2BS23 Transformer, 2US75 CONTROL VR701 95C0R854E1020 VR751 95C0R854E1020 J 1k J 1k 1/10W 1/10W AH AH CAPACITORS å C7001 å C7002 å C7004 å C7005 å C7006 C7008 C7009 C7010 C7011 C7012 C7013 C7014 C7015 C7016 C7017 C7020 C7022 C7023 C7024 å C7026 C7027 å C7101 C7102 C7104 C7105 C7106 C7108 C7109 C7110 C7111 C7112 C7151 C7152 C7201 C7202 C7203 C7205 C7206 C7207 C7208 C7209 C7210 C7211 C7213 C7301 C7302 C7303 C7304 C7351 C7352 C7353 147 95C0C245Q4740 95C0C1H8Q4710 95C0C1H8Q3320 95C0C1H8Q4710 95C0C245Q2240 95C0C1Q2B1040 95C0C247M4740 95C0C377M1R00 95C0C1Q1E4710 95C0C1Q1E1010 95C0C1Q2E1030 95C0C1Q1E3310 95C0C247M4740 95C0C1Q2B1040 95C0C195C0104 95C0C1A9R2210 95C0C3J6M1510 95C0C364E4R70 95C0C374D8200 95C0C245Q2240 95C0C195C0104 95C0C1H8Q4710 95CC3105MR100 95C0C1Q2E4720 95C0C194E1020 95C0C1Q1E1010 95C0C195E1040 95C0C1Q2E1030 95C0C1Q2E1030 95C0C1Q2E1030 95C0C195E1040 95C0C375B4710 95C0C195E1040 95C0C3J6M1510 95C0C157R1010 95C0C1AQR1020 95C0C1Q2E1030 95C0C195C0104 95C0C1Q2E1030 95C0C3A0D3300 95C0C1Q1E4710 95C0C1Q2E1030 95C0C1Q2C4730 95C0C1Q2E1030 95C0C1A9R2210 95C0C3A0C8210 95C0C3A0C8210 95C0C364E1R00 95C0C3A0C1520 95C0C1Q2B1040 95C0C374D5610 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.47 470p 3300p 470p 0.22 0.1 0.47 1 470p 100p 0.01 330p 0.47 0.1 0.1 220p 150 4.7 82 0.22 0.1 470p 10 4700p 1000p 100p 0.1 0.01 0.01 0.01 0.1 470 0.1 150 100p 1000p 0.01 0.1 0.01 33 470p 0.01 0.047 0.01 220p 820 820 1 1500 0.1 560 AC250V Film AC250V Ceramic AC250V Ceramic AC250V Ceramic AC250V Film 16V Ceramic 450V Film 400V Electrolytic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 450V Film 16V Ceramic 25V Ceramic 1KV Ceramic 400V Electrolytic 50V Electrolytic 35V Electrolytic AC250V Film 25V Ceramic AC250V Ceramic 400V Electrolytic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 16V Electrolytic 50V Ceramic 400V Electrolytic 1KV Ceramic 1KV Ceramic 50V Ceramic 25V Ceramic 50V Ceramic 35V Electrolytic 50V Ceramic 50V Ceramic 25V Ceramic 50V Ceramic 1KV Ceramic 25V Electrolytic 25V Electrolytic 50V Electrolytic 25V Electrolytic 16V Ceramic 35V Electrolytic AG AS AG AL AV AV AF AY AL AG AF AF AF AY AF XV-Z9000U/E Ref. No. ★ Part No. Description Code RDENC0329CEZZ POWER UNIT(Continued) C7354 C7401 C7402 C7403 C7404 C7405 C7406 C7407 C7408 C7409 C7410 C7411 C7412 C7413 C7417 C7428 å C7430 å C7431 å C7432 å C7433 95C0C1Q2B1040 95C0C3A0B1020 95C0C3A0B1020 95C0C3A0B1020 95C0C374A1020 95C0C374A1020 95C0C195C0104 95C0C195C0104 95C0C364E4R70 95C0C1Q2E1030 95C0C1Q2E1020 95C0C1Q1E2210 95C0C1Q2E3320 95C0C1Q2B1040 95C0C1A9R2210 95C0C374C1210 95C0C1H8Q1020 95C0C1H8Q1020 95C0C1H8Q4710 95C0C1H8Q4710 å R7001 R7002 R7003 R7004 R7005 R7006 R7007 R7008 R7009 R7010 R7012 R7013 R7014 R7015 R7016 R7017 R7018 R7019 R7020 R7021 R7022 R7023 R7025 R7026 R7029 R7031 R7032 R7034 R7035 R7036 R7037 R7038 R7039 R7040 R7041 R7042 R7043 R7044 R7045 R7046 R7047 R7048 R7049 R7050 R7051 R7052 R7053 R7054 R7055 R7056 95C0R105C2740 95C0R390T1000 95C0R390T1000 95C0R3Q4S1020 95C0R522F1000 95C0R522F1000 95C0R391T1840 95C0R451C1000 95C0R3Q8S2720 95C0R3Q4S1030 95C0R3Q8S3930 95C0R3Q4S1000 95C0R391T1840 95C0R391T1840 95C0R3Q4S2740 95C0R3Q4S3340 95C0R390T2200 95C0R390T4700 95C0R3Q4S3330 95C0R390T1000 95C0R516FR100 95C0R516FR100 95C0R362U1500 95C0R362U1500 95C0R391T2240 95C0R3Q4S1030 95C0R3Q4S1030 95C0R3Q4S1010 95C0R3Q8S2720 95C0R3Q8S3910 95C0R3Q8S2220 95C0R3Q4S1030 95C0R3Q4S3320 95C0R391T2240 95C0R391T2240 95C0R391T1840 95C0R391T1840 95C0R3Q4S1030 95C0R3Q4S2740 95C0R3Q4S2740 95C0R3Q8S1330 95C0R391T1840 95C0R3Q4S2220 95C0R391T4740 95C0R391T4740 95C0R3Q0V2730 95C0R390T5620 95C0R390T3340 95C0R390T3340 95C0R390T3340 J J J J J J J J J J J J J J J J J J J J 0.1 1000 1000 1000 1000 1000 0.1 0.1 4.7 0.01 1000p 220p 3300p 0.1 220p 120 1000p 1000p 470p 470p 16V Ceramic 16V Electrolytic 16V Electrolytic 16V Electrolytic 10V Electrolytic 10V Electrolytic 25V Ceramic 25V Ceramic 50V Electrolytic 50V Ceramic 50V Ceramic 50v Ceramic 50V Ceramic 16V Ceramic 1KV Ceramic 25V Electrolytic AC250V Ceramic AC250V Ceramic AC250V Ceramic AC250V Ceramic AF AH AH AG AG RESISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 270k 10 10 1k 10 10 180k 10 2.7k 10k 39k 10 180k 180k 270k 330k 10 47 33k 10 0.1 0.1 15 15 220k 10k 10k 100 2.7k 390 2.2k 10k 3.3k 220k 220k 180k 180k 10k 270k 270k 13k 180k 2.2k 470k 470k 27k 5.6k 330k 330k 330k 1W 1/4W 1/4W 1/16W 5W 5W 1/4W 1W 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 1/16W 1/16W 1/4W 1/4W 1/16W 1/4W 3W 3W 1/16W 1/16W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 1/4W 1/4W 1/16W 1/16W 1/16W 1/16W 1/4W 1/16W 1/4W 1/4W 1/8W 1/4W 1/4W 1/4W 1/4W AF AC AC AQ AQ AC AD AC AC AC AN AN AC AC AC AC AC AC AC 148 Ref. No. Part No. ★ R7057 R7061 R7101 R7102 R7103 R7104 R7105 R7106 R7107 R7108 R7110 R7112 R7113 R7114 R7115 R7116 R7117 R7118 R7119 R7120 R7121 R7123 R7124 R7125 R7126 R7127 R7151 R7152 R7153 R7154 R7155 R7156 R7157 R7158 R7159 R7201 R7202 R7207 R7208 R7209 R7210 R7211 R7212 R7213 R7215 R7217 R7218 R7219 R7220 R7221 R7301 R7302 R7303 R7304 R7305 R7306 R7307 R7308 R7309 R7351 R7352 R7353 R7354 R7355 R7401 R7402 R7403 R7404 R7405 R7406 R7407 R7408 R7409 R7411 R7412 R7413 95C0R391T4740 95C0R451C1000 95C0R3Q4S2240 95C0R3Q4S2710 95C0R3Q4S3330 95C0R3Q4S6810 95C0R3Q4S8220 95C0R3Q4S0000 95C0R3Q4S2230 95C0R3Q4S4730 95C0R3Q8S4740 95C0R3Q4S1040 95C0R390T3940 95C0R390T3940 95C0R3Q4S6820 95C0R3Q4S6830 95C0R3Q4S1030 95C0R3Q4S2240 95C0R3Q4S4730 95C0R3Q0V4730 95C0R390T3940 95C0R3Q4S1030 95C0R3Q4S1010 95C0R3Q4S1030 95C0R3Q4S1040 95C0R3Q4S1000 95C0R3Q4S8210 95C0R3Q4S5610 95C0R3Q4S6820 95C0R3Q4S5610 95C0R3Q8S2720 95C0R3Q4S1030 95C0R3Q4S1020 95C0R3Q4S6800 95C0R3Q8S2220 95C0R390T1500 95C0R390T1000 95C0R452D3930 95C0R452D3930 95C0R516FR220 95C0R390T1000 95C0R3Q4S1030 95C0R3Q4S1040 95C0R3Q4S1030 95C0R3Q4S1030 95C0R3Q8S1810 95C0R3Q8S1830 95C0R3Q4S1020 95C0R3Q4S1510 95C0R3Q4S1020 95C0R3Q4S2220 95C0R3Q4S2220 95C0R3Q4S1010 95C0R3Q4S1020 95C0R3Q4S6820 95C0R3Q4S1820 95C0R3Q4S4710 95C0R3Q8S2220 95C0R3Q8S1030 95C0R3Q4S2220 95C0R3Q4S8200 95C0R3Q1V2710 95C0R3Q8S1020 95C0R3Q8S4720 95C0R516FR050 95C0R516FR050 95C0R3Q8S2210 95C0R3Q4S1030 95C0R3Q4S1030 95C0R3Q4S1020 95C0R3Q4S2240 95C0R3Q4S1000 95C0R3Q4S6800 95C0R3Q4S1530 95C0R3Q4S8220 95C0R3Q4S1030 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 470k 10 220k 270 33k 680 8.2k 0 22k 47k 470k 100k 390k 390k 6.8k 68k 10k 220k 47k 47k 390k 10k 100 10k 100k 10 820 560 6.8k 560 2.7k 10k 1k 68 2.2k 10 10 39k 39k 0.22 10 10k 100k 10k 10k 180 18k 1k 150 1k 2.2k 2.2k 100 1k 6.8k 1.8k 470 2.7k 10k 2.2k 82 270 1k 4.7k 0.05 0.05 220 10k 10k 1k 220k 10 68 15k 8.2k 10k 1/4W 1W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 2W 2W 3W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 3W 3W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Code AD AC AC XV-Z9000U/E Ref. No. ★ Part No. Description Code RDENC0329CEZZ POWER UNIT(Continued) R7414 R7415 R7416 R7417 R7418 R7419 R7420 R7421 R7430 R7431 å R7432 å R7433 å R7434 95C0R3Q4S1030 95C0R3Q8S1530 95C0R3Q4S1030 95C0R3Q4S1030 95C0R3Q0V2730 95C0R3Q4S3910 95C0R3Q4S1000 95C0R3Q4S3910 95C0R3Q8S2220 95C0R3Q8S8210 95C0R390T5640 95C0R390T5640 95C0R390T5640 J J J J J J J J J J J J J 10k 15k 10k 10k 27k 390 10 390 2.2k 820 560k 560k 560k 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 1/4W J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Jumper, 5mm AD Ferrite Bead, BL02RN1-R62 T2 AD Ferrite Bead, BL02RN1-R62 T2 AD Ferrite Bead, BL02RN1-R62 T2 AD Connector Connector, B13B-PH-K-S Connector, B10B-PH-K-S Connector, B2B-PH-K-S Connector, AC-P07CN16 Connector, B2P3-VH AF Fuse, AC250V 6.3AH 215 Fuse, AC250V 1.6AH 215 Fuse Holder, TP00351-51 Fuse Holder, TP00351-51 Fuse Holder, TP00351-51 Fuse Holder, TP00351-51 Jumper, 7.5mm Relay, DJ5D2-0(M) TV-5 Bond Sheet Sheet Heat Sink Heat Sink Heat Sink Heat Sink SFH615AGR-X016 SFH615AGR-X016 SFH615AGR-X016 Panel Wire Ass’y HD6417709(SH7709) PST600IM AT24C128N-10SI-2.7 CXA3516AR ML87V2108 PQ05TZ11 PQ20VZ11 PST623XW TC7SB384FU CIVIC LH28F320S3NS-L11 MSM51V18165D-60TS-K GA4 TC7WH241FU TC74LVX86FT M62320FP SN74F153DB HD74HCT125T 9DK001-11024 9DK001-11024 9DK001-11024 9DK001-11024 9DK001-12068 9DK001-12089 9DK001-15087 9DK001-15089 9DK001-15089 9DK001-15062 VHIVPC3230D-1 9DK001-15072 9DK001-15100 9DK001-15089 9DK001-15089 9DK001-15089 J J J J J J J J J J J J J J J J Code HY57V653220BTC-7 HY57V653220BTC-7 HY57V653220BTC-7 HY57V653220BTC-7 SN74F153DB NC7ST08M5 NJM2137V TL712CPW TL712CPW LM404CIM3-4.1 VPC3230D M62320FP NJU7660M TL712CPW TL712CPW TL712CPW BN BN BN BN AM AG AS AR AR AS BG AS AR AR AR J IMB3A J 2SA1037AKQ J 2SC2412KQ AE AE AE D8001 D8002 D8009 D8020 D8051 9DK001-30015 9DK001-30015 9DK001-30018 9DK001-30018 9DK001-30019 X8001 X8003 X8004 X8005 X8006 9DK001-80012 9DK001-80011 9DK001-80018 9DK001-80030 9DK001-80020 FL8020 FL8021 FL8022 FI8023 FL8002 FL8003 FL8005 FL8006 FL8029 FL8030 FL8031 FL8032 FL8039 FL8040 FL8041 FL8094 FL8095 FL8096 FL8097 FL8100 FL8103 FL8111 FL8112 FL8113 FL8141 FL8142 FL8143 FL8144 FL8145 FL8146 FL8147 FL8148 FL8149 FL8150 FL8151 FL8152 FL8153 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-82025 9DK001-82025 9DK001-82025 9DK001-82025 9DK001-82025 9DK001-82025 9DK001-82025 9DK001-82025 9DK001-82025 9DK001-82024 9DK001-82024 9DK001-82024 9DK001-82024 J J J J J MA157A MA157A 1SS187(D3) 1SS187(D3) DALC112S1 AE AE AD AD AN PACKAGED CIRCUITS J J J J J CX-5F(6MHz 50PPM) FXO-31FL(1.8432MHz) FXO-31FL(25.000MHz) SG-636PCE(37.125MHz) 20.25MHz(CX-5F.CX-49F.SMD-49) AN AS AV AR FILTERS INTEGRATED CIRCUITS J J J J J J J J J J J J J J J J J J IC8319 IC8320 IC8321 IC8322 IC8325 IC8333 IC8334 IC8335 IC8336 IC8337 IC8338 IC8361 IC8362 IC8363 IC8364 IC8365 Description DIODES PC I/F UNIT RH-IX3270CEZZ 9DK001-15061 9DK001-11025 9DK001-15103 9DK001-15110 VHiPQ05TZ11-1* VHiPQ20VZ11-1 9DK001-15060 9DK001-12094 RH-iX3434CEZZ RH-iX3446CEZZ 9DK001-11017 RH-iX3399CEN1Q 9DK001-12055 9DK001-12057 9DK001-15072 9DK001-12068 9DK001-12070 ★ Q8012 9DK001-20025 Q8016 9DK001-20012 Q8017 9DK001-20011 CPCi-0051CE01/02 IC8001 IC8002 IC8003 IC8004 IC8005 IC8007 IC8008 IC8019 IC8023 IC8025 IC8027 IC8028 IC8029 IC8052 IC8053 IC8299 IC8302 IC8306 Part No. TRANSISTOR MISCELLANEOUS PARTS BEA7003 95C0W000A0050 BEA7014 95C0L551A0010 BEA7202 95C0L551A0010 BEA7204 95C0L551A0010 CN7003 95C0WPF2004 CN7101 95C0K202B0130 CN7102 95C0K202B0100 CN7103 95C0K202B0020 CN7104 95C0K206S0010 CN7106 95C0K251A0020 å F7001 95C0K718A6R30 å F7002 95C0K718A1R60 FH7001 95C0M850A0010 FH7002 95C0M850A0010 FH7003 95C0M850A0010 FH7004 95C0M850A0010 J7001 95C0W000A0070 å RL7001 95C0K3101AS01 LQD7001 95C0Z509A0010 SHT7001 95C0PPS1020 SHT7002 95C0PPS1020 HS7001 95C0MPF0017 HS7003 95C0MPF0017 HS7004 95C0MPF0019 HS7101 95C0MPF0018 å PC7101 95C0H710AS002 å PC7201 95C0H710AS002 å PC7202 95C0H710AS002 PL 95C0MPS0321B0 W7001 95C0CPS3820 Ref. No. BH AL AT AG AH AP AL BW BG BB BM AN AM AS AM AL 149 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 Filter NFA3216G2C100R470 NFA3216G2C100R470 NFA3216G2C100R470 NFA3216G2C100R470 NFA3216G2C100R470 NFA3216G2C100R470 NFA3216G2C100R470 NFA3216G2C100R470 NFA3216G2C100R470 BMS400 Filter BMS400 Filter BMS400 Filter BMS400 Filter AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AM AM AM AM AM AM AM AM AM AH AH AH AH XV-Z9000U/E Ref. No. ★ Part No. Description Code C8079 C8080 C8081 C8082 C8083 C8084 C8096 C8110 C8111 C8112 C8113 C8114 C8115 C8116 C8117 C8118 C8119 C8120 C8121 C8122 C8123 C8124 C8125 C8126 C8127 C8128 C8130 C8131 C8132 C8133 C8134 C8135 C8136 C8137 C8138 C8143 C8144 C8145 C8146 C8147 C8148 C8149 C8169 C8170 C8178 C8181 C8192 C8197 C8202 C8205 C8214 C8218 C8219 C8252 C8255 C8256 C8257 C8349 C8350 C8361 C8366 C8367 C8374 C8375 C8376 C8462 C8484 C8485 C8503 C8529 C8531 C8532 C8561 C8562 C8563 CPCi-0051CE01/02 PC I/F UNIT(Continued) COILS L8001 L8002 L8003 L8004 L8014 L8022 L8030 L8032 L8034 L8035 L8051 L8052 L8053 L8054 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81060 9DK001-81060 9DK001-81060 C8001 C8002 C8003 C8004 C8005 C8006 C8007 C8008 C8009 C8010 C8012 C8013 C8014 C8015 C8016 C8017 C8018 C8019 C8020 C8021 C8022 C8023 C8024 C8025 C8026 C8027 C8028 C8029 C8030 C8031 C8032 C8033 C8034 C8035 C8036 C8037 C8038 C8039 C8041 C8042 C8043 C8044 C8045 C8046 C8047 C8048 C8049 C8050 C8051 C8052 C8053 C8062 C8070 C8078 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42148 9DK001-42103 9DK001-42103 9DK001-42096 9DK001-42148 9DK001-42094 9DK001-42096 9DK001-42096 9DK001-42104 9DK001-42104 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-40077 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42105 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-40089 9DK001-40089 9DK001-42096 9DK001-42096 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42094 9DK001-42094 9DK001-42094 J J J J J J J J J J J J J J NLC322522T-3R3M 3.3uH NLC322522T-3R3M 3.3uH NLC322522T-3R3M 3.3uH NLC322522T-3R3M 3.3uH NLC322522T-3R3M 3.3uH NLC322522T-3R3M 3.3uH NLC322522T-3R3M 3.3uH NLC322522T-3R3M 3.3uH NLC322522T-3R3M 3.3uH NLC322522T-3R3M 3.3uH NLC322522T-3R3M 3.3uH BLM21B201SPT BLM21B201SPT BLM21B201SPT AG AG AG AG AG AG AG AG AG AG AG AF AF AF CAPACITORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.1 0.1 0.1 0.1 0.1 0.01 0.01 0.01 0.01 10 15p 15p 0.01 10 0.1 0.01 0.01 470p 470p 0.01 0.01 0.01 10 0.01 0.01 0.01 0.01 0.01 0.047 0.1 0.1 0.1 0.01 0.01 0.01 0.01 0.01 47 47 0.01 0.01 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.01 0.01 0.01 0.1 0.1 0.1 25V 25V 25V 25V 25V 50V 50V 50V 50V 35V 50V 50V 50V 35V 25V 50V 50V 50V 50V 50V 50V 50V 16V 50V 50V 50V 50V 50V 50V 25V 25V 25V 50V 50V 50V 50V 50V 6.3V 6.3V 50V 50V 25V 25V 25V 25V 25V 25V 25V 50V 50V 50V 25V 25V 25V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ref. No. AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AF AC AC AC AC AC AC AC AC AC AC AC AC AC AC AE AE AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC 150 Part No. 9DK001-40078 9DK001-40079 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-40089 9DK001-40089 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42111 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42111 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42099 9DK001-42149 9DK001-42099 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42096 9DK001-40089 9DK001-42096 9DK001-40089 9DK001-42096 9DK001-40089 9DK001-42096 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-40080 9DK001-40092 9DK001-42094 9DK001-40080 9DK001-42096 9DK001-42096 9DK001-40089 9DK001-40080 9DK001-40091 9DK001-40080 9DK001-40091 9DK001-40079 9DK001-42094 9DK001-40089 9DK001-42094 9DK001-40089 9DK001-42096 9DK001-40089 9DK001-42096 9DK001-42099 9DK001-42094 9DK001-42094 ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 22 47 0.01 0.01 0.01 47 47 0.1 0.1 0.1 1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 1 0.1 0.1 0.1 0.1 100p 0.33 100p 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.01 47 0.01 47 0.01 47 0.01 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 100 220 0.1 100 0.01 0.01 47 100 100 100 100 47 0.1 47 0.1 47 0.01 47 0.01 100p 0.1 0.1 16V 16V 50V 50V 50V 6.3V 6.3V 25V 25V 25V 10V 25V 25V 25V 25V 25V 25V 25V 25V 10V 25V 25V 25V 25V 50V 16V 50V 25V 25V 25V 25V 25V 25V 25V 25V 50V 6.3V 50V 6.3V 50V 6.3V 50V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 6.3V 4V 25V 6.3V 50V 50V 6.3V 6.3V 4V 6.3V 4V 16V 25V 6.3V 25V 6.3V 50V 6.3V 50V 50V 25V 25V Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Film Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Code AF AG AC AC AC AE AE AC AC AC AB AC AC AC AC AC AC AC AC AB AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AE AC AE AC AE AC AC AC AC AC AC AC AC AC AC AC AC AF AF AC AF AC AC AE AF AF AF AF AG AC AE AC AE AC AE AC AC AC AC XV-Z9000U/E Ref. No. Part No. ★ Description Code Ref. No. AE AC AC AE AE AC AC AC AC AC AC AC AC AC AC AC AC AE AE AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC C8678 C8680 C8682 C8684 C8685 C8686 C8687 C8688 C8689 C8697 C8707 C8708 C8742 C8743 C8755 C8757 C8759 C8767 C8770 C8771 C8772 C8773 C8774 C8775 C8776 C8777 C8778 C8785 C8786 C8787 C8788 C8789 C8790 C8791 C8792 C8793 C8794 C8795 C8796 C8797 C8798 C8799 C8800 C8801 C8802 C8803 C8804 C8805 C8806 C8807 C8808 C8809 C8810 C8811 C8812 C8813 C8814 C8815 C8816 C8817 C8818 C8819 C8824 C8825 C8827 C8828 C8861 C8862 C8863 C8864 C8865 C8866 C8867 C8871 C8872 CPCi-0051CE01/02 PC I/F UNIT(Continued) C8564 C8565 C8566 C8573 C8574 C8575 C8576 C8577 C8578 C8579 C8580 C8581 C8582 C8583 C8584 C8585 C8586 C8587 C8588 C8589 C8590 C8591 C8592 C8593 C8594 C8595 C8596 C8597 C8598 C8599 C8600 C8601 C8603 C8605 C8607 C8609 C8611 C8613 C8615 C8617 C8619 C8621 C8623 C8625 C8627 C8629 C8631 C8633 C8635 C8637 C8638 C8640 C8641 C8644 C8645 C8648 C8649 C8652 C8654 C8656 C8658 C8660 C8662 C8664 C8666 C8667 C8668 C8670 C8672 C8674 C8676 9DK001-40089 9DK001-42094 9DK001-42123 9DK001-40089 9DK001-40089 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-40089 9DK001-40089 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42096 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 47 0.1 330p 47 47 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 47 47 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.01 0.1 0.1 0.1 0.1 0.1 0.1 6.3V 25V 50V 6.3V 6.3V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 6.3V 6.3V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 50V 25V 25V 25V 25V 25V 25V Electrolytic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic 151 Part No. 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42096 9DK001-42094 9DK001-40090 9DK001-40079 9DK001-42094 9DK001-42094 9DK001-42113 9DK001-42096 9DK001-40104 9DK001-42094 9DK001-42130 9DK001-42094 9DK001-42111 9DK001-42094 9DK001-42094 9DK001-40104 9DK001-42094 9DK001-40093 9DK001-42144 9DK001-42144 9DK001-42144 9DK001-42144 9DK001-42144 9DK001-42148 9DK001-42148 9DK001-42139 9DK001-42139 9DK001-42116 9DK001-42116 9DK001-40092 9DK001-42094 9DK001-42105 9DK001-40091 9DK001-40077 9DK001-42143 9DK001-42130 9DK001-42123 9DK001-42143 9DK001-42115 9DK001-42115 9DK001-42123 9DK001-42143 9DK001-42123 9DK001-42143 9DK001-42139 9DK001-42116 9DK001-42139 9DK001-42105 9DK001-42142 9DK001-42142 9DK001-42142 9DK001-42139 9DK001-42105 9DK001-42096 9DK001-40089 9DK001-42142 9DK001-40092 9DK001-42094 9DK001-40077 9DK001-42096 9DK001-40089 9DK001-42094 9DK001-42094 9DK001-42112 9DK001-42094 9DK001-42094 ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.01 0.1 47 47 0.1 0.1 4.7 0.01 6.8 0.1 2200p 0.1 1 0.1 0.1 6.8 0.1 0.47 0.68 0.68 0.68 0.68 0.68 10 10 1500p 1500p 390p 390p 220 0.1 0.047 100 10 0.22 2200p 330p 0.22 10p 10p 330p 0.22 330p 0.22 1500p 390p 1500p 0.047 0.068 0.068 0.068 1500p 0.047 0.01 47 0.068 220 0.1 10 0.01 47 0.1 0.1 33p 0.1 0.1 25V 25V 25V 25V 25V 25V 25V 25V 25V 50V 25V 4V 16V 25V 25V 10V 50V 10V 25V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic OS Ceramic Ceramic 25V Ceramic 10V Ceramic 25V Ceramic 25V Ceramic 10V OS 25V Ceramic 50V Electrolytic 10V Ceramic 10V Ceramic 10V Ceramic 10V Ceramic 10V Ceramic 35V Ceramic 35V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 4V Electrolytic 25V Ceramic 50V Ceramic 4V Electrolytic 16V Electrolytic 16V Ceramic Ceramic 50V Ceramic 16V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 16V Ceramic 50V Ceramic 16V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 6.3V Electrolytic 50V Ceramic 4V Electrolytic 25V Ceramic 16V Electrolytic 50V Ceramic 6.3V Electrolytic 25V Ceramic 25V Ceramic 50V Ceramic 25V Ceramic 25V Ceramic Code AC AC AC AC AC AC AC AC AC AC AC AF AG AC AC AB AC AC AC AC AC AB AC AC AC AC AE AC AC AC AC AC AC AC AC AC AC AC AF AC AC AF AF AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AE AC AF AC AF AC AE AC AC AB AC AC XV-Z9000U/E Ref. No. ★ Part No. Description Code R8124 R8128 R8130 R8131 R8132 R8133 R8138 R8140 R8143 R8144 R8145 R8146 R8147 R8148 R8268 R8289 R8296 R8340 R8447 R8448 R8463 R8464 R8466 R8568 R8573 R8576 R8598 R8599 R8601 R8602 R8650 R8651 R8652 R8653 R8654 R8655 R8656 R8684 R8687 R8688 R8689 R8690 R8691 R8692 R8693 R8694 R8695 R8696 R8697 R8698 R8699 R8700 R8701 R8702 R8708 R8741 R8745 R8747 R8749 R8757 R8758 R8759 R8760 R8860 R8862 R8864 R8866 R8867 R8868 R8869 R8875 R8883 R8885 R8887 R8892 CPCi-0051CE01/02 PC I/F UNIT(Continued) C8874 C8875 C8877 C8878 9DK001-42094 9DK001-42094 9DK001-42112 9DK001-42112 FL8001 FL8098 FL8099 FL8110 FL8114 R8001 R8005 R8006 R8007 R8010 R8011 R8015 R8016 R8017 R8018 R8019 R8022 R8025 R8026 R8027 R8029 R8030 R8031 R8032 R8033 R8034 R8035 R8036 R8037 R8038 R8039 R8040 R8041 R8042 R8043 R8044 R8045 R8046 R8047 R8050 R8051 R8053 R8057 R8058 R8062 R8065 R8069 R8070 R8071 R8072 R8075 R8080 R8083 R8084 R8085 R8088 R8091 R8092 R8093 R8094 R8095 R8096 R8121 R8122 R8123 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-51036 9DK001-50165 9DK001-50185 9DK001-50185 9DK001-51030 9DK001-51030 9DK001-50149 9DK001-50198 9DK001-50210 9DK001-50199 9DK001-51030 9DK001-50185 9DK001-50162 9DK001-50075 9DK001-50209 9DK001-51030 9DK001-50075 9DK001-50149 9DK001-50075 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-50185 9DK001-50185 9DK001-50075 9DK001-50163 9DK001-50075 9DK001-50075 9DK001-51030 9DK001-51030 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-51030 9DK001-51030 9DK001-50149 9DK001-51030 9DK001-51030 9DK001-51029 9DK001-51030 9DK001-50149 9DK001-50165 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50044 9DK001-50159 9DK001-50149 9DK001-50149 9DK001-50044 9DK001-50159 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-50186 9DK001-50044 9DK001-52292 9DK001-52292 9DK001-50256 J J J J 0.1 0.1 33p 33p 25V 25V 50V 50V Ceramic Ceramic Ceramic Ceramic AC AC AB AB RESISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0 1/10W 0 1/10W 0 1/10W 0 1/10W 0 1/10W 100 1/16W 100 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 0 1/16W 1.69k1/16W 33k 1/16W 2.15k1/16W 10k 1/16W 10k 1/16W 56 1/16W 75 1/10W 27k 1/16W 10k 1/16W 75 1/10W 0 1/16W 75 1/10W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 75 1/10W 68 1/16W 75 1/10W 75 1/10W 10k 1/16W 10k 1/16W 0 1/16W 0 1/16W 0 1/16W 10k 1/16W 10k 1/16W 0 1/16W 10k 1/16W 10k 1/16W 10 1/16W 10k 1/16W 0 1/16W 100 1/16W 22 1/16W 22 1/16W 22 1/16W 68 1/10W 22 1/16W 0 1/16W 0 1/16W 68 1/10W 22 1/16W 0 1/16W 0 1/16W 0 1/16W 22k 1/16W 68 1/10W 8.2 1/4 8.2 1/4 1.6k 1/16W Ref. No. Chip2125 AB Chip2125 AB Chip2125 AB Chip2125 AB Chip2125 AB Resistor Array AD Chip1608 AA Chip1608 AA Chip1608 AA Resistor Array AD Resistor Array AD Chip1608 AB Chip1608 AB Chip1608 AA Chip1608 AB Resistor Array AD Chip1608 AA Chip1608 AA Chip2125 AB Chip1608 AA Resistor Array AD Chip2125 AB Chip1608 AB Chip2125 AB Resistor Array AD Resistor Array AD Resistor Array AD Resistor Array AD Chip1608 AA Chip1608 AA Chip2125 AB Chip1608 AA Chip2125 AB Chip2125 AB Resistor Array AD Resistor Array AD Chip1608 AB Chip1608 AB Chip1608 AB Resistor Array AD Resistor Array AD Chip1608 AB Resistor Array AD Resistor Array AD Resistor Array AD Resistor Array AD Chip1608 AB Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip2125 AB Chip1608 AA Chip1608 AB Chip1608 AB Chip2125 AB Chip1608 AA Chip1608 AB Chip1608 AB Chip1608 AB Chip1608 AA Chip2125 AB Chip1608 Chip1608 Chip1608 AB 152 Part No. 9DK001-50237 9DK001-50150 9DK001-50210 9DK001-50210 9DK001-50289 9DK001-50155 9DK001-50149 9DK001-50149 9DK001-50176 9DK001-50176 9DK001-50176 9DK001-50165 9DK001-50165 9DK001-50165 9DK001-50162 9DK001-50207 9DK001-50162 9DK001-50185 9DK001-50150 9DK001-50150 9DK001-50185 9DK001-50185 9DK001-50185 9DK001-50162 9DK001-50149 9DK001-50149 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-50185 9DK001-51037 9DK001-51030 9DK001-50185 9DK001-50204 9DK001-50185 9DK001-50183 9DK001-50176 9DK001-50173 9DK001-50201 9DK001-50173 9DK001-50205 9DK001-50205 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50185 9DK001-50185 9DK001-50185 9DK001-50185 9DK001-50218 9DK001-50257 9DK001-51030 9DK001-51030 9DK001-50159 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-50177 9DK001-50177 9DK001-50104 9DK001-50165 9DK001-50177 9DK001-50177 9DK001-50275 9DK001-50275 9DK001-50275 9DK001-50162 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-50165 ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 1.0k 10 33k 33k 3.3k 3k 0 0 820 820 820 100 100 100 56 6.8k 56 10k 10 10 10k 10k 10k 56 0 0 56 56 56 56 10k 6.8k 10k 10k 150 10k 4.7k 820 470 15 470 1.8k 1.8k 22 22 22 22 10k 10k 10k 10k 20k 75 10k 10k 22 0 0 0 0 0 1k 1k 330 100 1k 1k 6.8 6.8 6.8 56 0 0 0 100 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Code Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 Chip1608 AB Chip1608 AB Chip1608 AB Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AB Chip1608 AB Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Resistor Array AD Resistor Array AD Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Resistor Array AD Resistor Array AD Chip1608 AA Chip1608 AB Chip1608 AB Chip1608 AB Chip1608 AB Chip1608 AB Chip1608 AA Chip1608 AA Chip2125 AB Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AB Chip1608 AB Chip1608 AB Chip1608 AA Chip1608 AA Chip1608 AB Chip1608 AB Chip1608 AA XV-Z9000U/E Ref. No. Part No. ★ Description Code CPCi-0051CE01/02 PC I/F UNIT(Continued) R8893 R8894 R8896 R8897 R8898 R8899 R8900 R8911 R8912 R8913 R8914 R8918 R8922 R8924 R8925 R8926 R8927 R8929 R8930 R8931 R8933 R8935 R8966 R8967 R8968 R8969 R8970 R8971 R8972 R8973 R8974 R8976 R8977 R8978 R8979 R8980 R8981 R8982 R8983 R8984 R8987 R8988 R8990 R8991 R8992 R8993 R8994 R8995 9DK001-50197 9DK001-50210 9DK001-50191 9DK001-50161 9DK001-50185 9DK001-50208 9DK001-50196 9DK001-50177 9DK001-50075 9DK001-50075 9DK001-50075 9DK001-51039 9DK001-51039 9DK001-51039 9DK001-51039 9DK001-51039 9DK001-51039 9DK001-51039 9DK001-51039 9DK001-51039 9DK001-50149 9DK001-50149 9DK001-50244 9DK001-50177 9DK001-50170 9DK001-50179 9DK001-50149 9DK001-50150 9DK001-50150 9DK001-50150 9DK001-50149 9DK001-50150 9DK001-50149 9DK001-50111 9DK001-50111 9DK001-50111 9DK001-50149 9DK001-50177 9DK001-50177 9DK001-50177 9DK001-50244 9DK001-50244 9DK001-50177 9DK001-50177 9DK001-50170 9DK001-50170 9DK001-50179 9DK001-50179 SHIELD8001 SHIELD8002 RUB8001 RUB8002 S8001 P8404 P8405 P8502 P8002 PSLDM3044CEFW PSLDM3045CEFW 9DK001-99052 9DK001-99051 9DK001-70012 9DK001-60069 9DK001-60069 9DK001-60069 9DK001-60068 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 2.7k 33k 150 47 10k 12k 1.1k 1k 75 75 75 56 56 56 56 56 56 56 56 56 0 0 3.9k 1k 270 2.2k 0 10 10 10 0 10 0 75 75 75 0 1k 1k 1k 3.9k 3.9k 1k 1k 270 270 2.2k 2.2k 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/10W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4 1/4 1/4 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Chip1608 AB Chip1608 AA Chip1608 AB Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AB Chip1608 AA Chip2125 AB Chip2125 AB Chip2125 AB Resistor Array AD Resistor ArrayAD Resistor ArrayAD Resistor ArrayAD Resistor ArrayAD Resistor ArrayAD Resistor ArrayAD Resistor ArrayAD Resistor ArrayAD Chip1608 AB Chip1608 AB Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AB Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AB Chip1608 AA Chip1608 AB Chip3216 AB Chip3216 AB Chip3216 AB Chip1608 AB Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA Chip1608 AA MISCELLANEOUS PARTS DB8001 9DK001-60056 J8003 9DK001-60057 J8005 9DK001-60058 NEJI8001 9DK001-99050 NEJI8002 9DK001-99050 NEJI8003 9DK001-99050 J J J J J J J J J J J J J J J Shield Cace (Upper) Shield Cace (Lower) Radiator Sheet AK Radiator Sheet AS Slide Switch, SSSS812-B-2B AL Connector, 179029-2 60pin Connector, 179029-2 60pin Connector, 179029-2 60pin Connector, 177802-9 DSUB15pin Connector, 53261-0490 Connector, 55176-3091 Connector, FH12-50S-0.5SH Screw, M2.5x6 Screw, M2.5x6 Screw, M2.5x6 153 Ref. No. Part No. ★ Description Code XV-Z9000U/E Ref. No. Part No. ★ Description Code CABINET AND MECHANICAL PARTS 1 1-1 1-1 1-1-1 1-1-2 1-1-3 1-1-4 1-1-5 1-1-6 1-1-7 1-1-8 1-1-9 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-20 Not Available DBDYT1206CE01 DBDYT1209CE01 Not Available GCOVA1981CESA HBDGS3153CESA HiNDP5799CESA HiNDP5845CESA PFILD0139CEZZ PMLT-0395CEZZ PSPAH0708CEZZ PSPAH0709CEZZ GCOVA1989CEKA GCOVA1991CEZZ GDORT1097CEKA LANGT9027CEFD LANGT9029CEFD LANGT9030CEFW LX-NZ3155CEFF MSPRD0087CEFW NGERH3000CEFD NSFTZ0177CEFW PDMPF0102CEZZ PKAi-0004GEZZ PMLT-0397CEZZ PMLT-0398CEZZ PSLDP3090CE00 PSPAT0020CEZZ QCNW-5955CEZZ XBBSF20P05000 XEBSD30P10000 J J J J J J J J U J J J J J J J U J J J J J J J J J J J J J 2 2-1 Not Available DBDYU1136CE01 2-1 DBDYU1136CE03 2-1-1 2-1-2 2-1-3 2-1-4 2-1-5 2-1-5 2-1-6 2-1-6 2-1-7 2-1-8 2-1-9 2-1-10 2-1-11 2-1-12 2-1-13 2-1-14 2-1-15 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 Not Available GCOVA1980CESA GCOVA2016CEKA HiNDP5781CESC HiNDP5813CEZZ HiNDP5938CEZZ HiNDP5815CEZZ HiNDP5891CEZZ LANGF2134CEFW LHLDZ2077CEKZ LX-NZ3135CEFW PFILD0135CEZZ PFILD0136CEZZ PFILD0137CEZZ PMLT-0400CEZZ PMLT-0403CEZZ PSLDP3092CE00 GCOVA1990CEKA GCOVA2033CEKA GLEGP1020CEKE GLEGP3019CEKE HPNC-0469CESA PCOVU3012CEZZ PDUC-0147CEKZ PDUC-0148CEKZ PDUC-0159CEKZ PSLDP3091CE00 PSPAZ0428CEZZ PSPAZ0443CEZZ RH-HZ0091CEZZ XEBSD30P12000 XEBSD40P16000 XEPSD30P06000 J Bottom Body Ass’y J Bottom Body Ass’y (XV-Z9000U) J Bottom Body Ass’y (XV-Z9000E) - Bottom Body J Front R/C Cover J Exhaust Panel J Hot Caution J FCC Label (XV-Z9000U) J Caution Label (XV-Z9000E) J Model Label (XV-Z9000U) J Model Label (XV-Z9000E) J K Lock J K Lock Cover J Insert Nut, x3 J Intake Filter A J Intake Filter B J Intake Filter J Molt J Molt J Rubber Button J Lens Cover (Lower) J Hole Cover, x2 J Adjuster (R) J Adjuster (L) J Intake Punching, x2 J Intake Cover J Out Duct 1 J Out Duct 2 J Intake Duct J Rubber B J Duct Spacer J Duct Spacer J Thermistor-A J Screw, x12 J Bottom Spacer, x7 J Screw 3 CCOVA1984CE01 J Lamp Door Ass’y Top Body Ass’y — Top Body Ass’y(XV-Z9000U) BY Top Body Ass’y(XV-Z9000E) Top Body — Rear R/C Cover AE SHARP VISION Badge AQ Lens Warning Label Operation Indication AG Back Intake Filter AH Molt Spacer, x3 Spacer Lens Cover (Upper) AY LED Decoration AG Opration Door AN Door Shaft Angle A AF Door Shaft Angle B AG Connection Angle AE Speed Nut, x6 AF Door Spring AD Door Gear AF Door Shaft AH Dumper Latch AK Lens Molt AE LED Molt, x2 AA Rubber A AK Tefron Tape AD Connecting Cord(RE) AG Screw AA Screw, x8 AA — CA — AE BC AM AL AE AD AD AG AY AE AU AU AK AK AV AV AN AK AD AG AL AA AA AA Ref. No. 154 ★ Description Code 3-1 3-2 3-3 3-4 3-5 Not Available HiNDP5910CESA LX-BZ1009CEFN MSPRC0202CEFW XRESJ30-06000 J J J J Lamp Door Lamp Caution(XV-Z9000U) Screw, x2 Door Spring, x2 E-Ring, x2 4 4-1 4-2 4-3 4-4 CCOVA1985CE01 Not Available PCLiC1034CEKZ PCLiC1035CEKZ SSAKA1109CEZZ J J J J Terminal Cover Ass’y Terminal Cover Cover Clip Cover Clip Plun Cover Sack BB — AC 5 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 CDUC-0154CE01 NFANR0072CE00 PDUC-0154CEKZ PDUC-0160CEKZ PMLT-0393CEZZ PMLT-0394CEZZ PSPAZ0445CEZZ LHLDW1046CEZZ XEBSD30P12000 J J J J J J J J J HDDE Duct Ass’y Fan Power Duct A Power Duct B Power Molt A Power Molt B Fan Spacer Wire Holder Screw, x3 BA AX 6 Refer to Optics Mechanism Parts 7 7-1 7-2 7-3 7-4 7-5 CCASZ0109CE01 LHLDZ3058CEFW PCASZ0109CEKZ PCOVZ3028CEFW PSLDP3086CEFW TLABZ0787CEZZ J J J J J J 8 8-1 8-2 CCASZ0110CE01 Not Available PSLDP3093CEFW J Lamp Cace B Ass’y - Lamp Cace B J Shield B AT — 9 9-1 Not Available DPNLH1107CE01 — DD 9-1 DPNLH1107CE03 9-2 9-2 9-3 HiNDP5804CESA HiNDP5890CESA LX-NZ3155CEFF J Rear Body Ass’y J Rear Body Ass’y (XV-Z9000U) J Rear Body Ass’y (XV-Z9000E) J Rear Indicator(XV-Z9000U) J Rear Indicator(XV-Z9000E) J Speed Nut 10 Not Available 10-1 DPNLC1733CE01 10-1-1 Not Available 10-1-2 HiNDP5848CEZZ J J J J — BC — AD 10-1-3 10-2 10-3 10-4 LX-NZ3135CEFW LX-HZ3105CEFD PSPAT0080CEZZ QCNW-4674CEZZ J J J J Lamp Panel Ass’y Lamp Panel Ass'y Lamp Panel Inter Lock Indication (XV-Z9000U) Nut, 2 Screw Tefron Tape Door Switch 11 11 11-1 11-2 11-3 11-4 CPCi-0051CE01 CPCi-0051CE02 PSLDM3044CEFW PSLDM3045CEFW XBPSD30P06R00 Not Available J J J - PC I/F Unit Ass'y(XV-Z9000U) PC I/F Unit Ass'y(XV-Z9000E) PC I/F Shield (Upper) PC I/F Shield (Lower) Screw PC I/F PWB — — AK AL AB — 12 12-1 12-2 12-3 12-4 12-5 12-6 12-7 12-8 CSLDM3042CE01 PSLDM3042CEFW LHLDW1220CEZZ LX-BZ3266CEFD LX-LZ1014GE00 PGIDM0162CEKZ PMLT-0399CEZZ PSHEG0033CEZZ RH-HZ0092CEZZ J J J J J J J J J Shield Ass'y Power Unit Shield Cover Screw, x3 Rivet Ventilating Guide B Power Shield Molt Radiator Sheet Thermistor-B AW AD AA AA AD AG AV AL Not Available Not Available Not Available Not Available Not Available - Main Unit Key Unit R/C Receiver (Front) Unit R/C Receiver (Rear) Unit LED Unit — — — — — 13 14 15 16 17 BD Part No. Lamp Cace A Ass’y Handle Lamp Cace A Punching Shield Caution Label — AE AB AA AK AC AD AC AA AA AX AE AS AG AL AF AD AB AK XV-Z9000U/E CABINET AND MECHANICAL PARTS/ GEHÄUSE UND MECHANISCHE BAUTEILE 11-3 H 72 1-4 72 57 1-1-5 1-1-4 1 1-13 1-1-3 11-1 11 1-1-6 1-16 80 1-8 9-3 32 E 16 70 D 1-20 C 25 38 77 1-8 G 9 11-4 1-8 1-1-1 37 29 1-1-2 B 1-14 37 N 1-2 A 72 14 1-7 1-7 9-2 32 9-1 K M 29 1-1-9 1-8 1-20 11-2 38 L 72 46 1-5 32 17 1-15 1-20 1-20 1-1-8 1-10 1-11 P J 1-12 26 77 64 F A 1-19 1-1 G 55 1-3 1-20 H 77 1-9 12 O 1-6 13 79 50 77 1-20 F 12-2 12-2 1-18 28 1-17 12-1 32 5-5 5-8 12-8 12-2 56 79 5-8 12-6 N P 1-1-7 Z 12-5 32 12-3 5-3 7 21 Y 32 5-7 12-3 77 32 7-1 12-7 5-8 32 66 32 E 20 12-5 5-6 82 5-1 76 12-4 12-3 5-6 63 41 5-2 Y 54 H 5-4 7-5 53 5 62 67 76 M R Q 47 45 30 19 72 64 8-2 7-3 72 7-2 G 77 D 8-1 7-4 82 72 33 32 32 48 27 65 8 82 35 74 86 49 78 2-13 48 42 48 23 49 52 D 36 75 2-16 51 49 S 31 C C 60 B 74 2-16 L 32 2-1-15 61 44 2-1-12 59 2-12 2-8 2-17 2-11 K 2-10 F 77 32 Z 34 2-1-13 68 22 79 2-1-14 71 2-1-11 43 2-1-10 83 2-9 71 Q 81 18 2-15 85 84 2-1-8 2-1 40 6 39 2-1-7 2-15 77 B 4 S 2-3 2-6 2-15 4-3 2-15 4-1 4-2 E 2-2 71 3-3 3-4 3-2 3-1 77 2-1-2 10-4 3-5 3 2-1-4 24 10-1-2 2-5 10-1-1 2-15 32 2-7 2-1-1 R 2-1-3 2-1-6 10-2 2-14 2-1-5 15 A 58 J 3-5 2 2-4 O 10-3 69 2-6 2-1-9 10-1 10-1-3 1 2 10 3 4 155 5 6 XV-Z9000U/E Ref. No. Part No. ★ Description Code Ref. No. CABINET AND MECHANICAL PARTS (Continued) 18 19 20 21 22 23 24 JKNBZ1082CEKA LANGK0773CEFW LANGK0774CEFW LANGK0777CEFW LANGK0783CEFW LANGK0786CEFW LANGQ5725CEFW J J J J J J J 25 LANGQ5726CEFW J 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 å 67 68 69 69 70 71 72 74 75 76 77 78 79 80 81 82 83 84 85 86 LANGQ5727CEFW LHLDF1201CEZZ LHLDW1046CEZZ LHLDW1047CEUZ LHLDW1060CEZZ LHLDW1064CEZZ LX-BZ3266CEFD LX-EZ3011CEFD NFANS0006CE00 NFANS0029CEZZ NFANS0088CE00 NSFTZ0134CEFW NSFTZ0178CEFW PCAPH1056CESA PDUC-0158CEKZ PGiDM0160CEKZ PGiDM0163CEKZ PSLDM3039CEFW PSLDM3040CEFW PSLDM3041CEFW PSLDM3046CEFW PSPAN0022CEKZ PSPAZ0419CEZZ PSPAZ0426CEZZ PSPAZ0435CEKZ PSPAZ0441CEZZ PSPAZ0445CEZZ PZETK0139CEKZ PZETK0141CEKZ QCNW-5954CEZZ QCNW-5956CEZZ QCNW-5957CEZZ QCNW-5958CEZZ QCNW-5959CEZZ QCNW-5962CEZZ QCNW-5963CEZZ QCNW-5964CEZZ QCNW-5965CEZZ QEARZA001WJZZ Not Available Not Available RLMPF0074CEZZ Not Available TLABN0401CEZZ TLABN0400CEZZ XBBSN30P10000 XBBSN40P10000 XBPSD30P08R00 XBPSD30P18JS0 XBPSD40P16J00 XBTSC40P12000 XEBSD30P08000 XEBSD30P12000 XEBSD40P16000 XEBSN30P10000 XEPSD30P06000 XESSF30P06000 LHLDW1033CEKZ QCNE-5966CEZZ RBIM-0104CEZZ LHLDW1141CEZZ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Lens Shift Knob AK Lamp Plug Angle Reflecton Plate Fixing Angle Lamp Socket Angle AF Color Wheel Fan Angle AH Fan Angle AH R/C Receiver (Front) Fixing AF Angle R/C Receiver (Rear) Fixing Angle LED PWB Fixing Angle AG Ballast Holder AD Wire Holder AA Wire Holder AA Wire Holder AB Wire Holder AB Screw, x20 AA Screw, x3 AC Color Wheel Fan BB Out Fan BC PWB Cooling fan AY D-Sub Nut AD PWB Shaft AF Lens Cap AW Inner Guide AM Ventilating Guide A AL Ventilating Guide C AF Formatter Shield A AT Formatter Shield B AX Power Unit Frame AP Rear terminal Shield AK Spacer AC Out-Fan Bush AC Fan Spacer AB PWB Spacer AC Out Fan Spacer AD Fan Spacer AC Insulation Sheet (Power) AM Insulation Sheet (Ballast) AP Connecting Wire (KY) Connecting Cord (CA) AG R/C Wire (Rear) R/C Wire (Front) Connecting Cord (J2) AN Connecting Cord (J3) AP Connecting Cord (J5) AM Connecting Cord (EA) AK Connecting Cord (EB) AH Earth, x2 AL Power Unit — Ballast unit — Lamp Formatter unit — S/I No. Label (XV-Z9000U) S/I No. Label (XV-Z9000E) Screw, x2 Screw, x6 AB Screw, x13 AB Screw, x8 AA Screw, x3 AA Screw, x3 AB Screw, x7 AA Screw, x2 AA Screw, x10 AA Screw, x3 AA Screw, x2 AA Screw, x3 AA Wire Holder for Bimetal Bimetal Wire Holder AE Part No. ★ Description Code OPTICS MECHANISM PARTS 6 6-1 6-2 6-3 6-4 CCHSK0103CE01 9HN-3623-0041 9HN-3623-0042 9HN-3622-0500 9HN-3623-0043 J J J J J 6-5 6-6 6-7 6-8 6-9 6-10 6-11 6-12 6-13 6-14 6-15 6-16 6-17 6-18 6-19 6-20 6-21 9HN-9670-03067 9HN-3623-4171 9HN-3623-0044 9HN-9739-03087 9HN-3623-4173 9HN-3623-4174 9HN-3623-4175 9HN-3623-4177 9HN-9642-26107 9HN-3623-4176 9HN-9612-20807 9HN-9716-02007 9HN-3623-0045 9HN-9762-20607 9HN-3623-4152 9HN-9670-02047 9HN-9716-02007 J J J J J J J J J J J J J J J J J Optics Mechanism Ass’y DZ Optics Mechanism Ass’y Cover Ass’y Projection Lens Projection Lens Fixin Plate Ass’y, x2 Screw, x4 Color Wheel Cover 1 Color Wheel Cover 2 Ass’y Screw, x4 Dumpping Rubber A Dumpping Rubber B Spacer A, x3 Spacer B, x4 Screw, x3 Washer, x3 Screw, x4 Washer, x4 G7 Lens Ass’y Screw, x2 Color Wheel Sensor PWB Screw, x2 Washer, x2 6-22 6-22-1 6-22-2 å 6-22-3 6-22-4 6-22-5 6-22-6 6-22-7 BQC-XVZ9000/1 CCASZ0109CE01 CCASZ0110CE01 RLMPF0074CEZZ LANGK0774CEFW LANGK0773CEFW XEBSD30P08000 XESSF30P08000 J J J J J J J J Lamp Unit Lamp Case (A) Ass’y Lamp Case (B) Ass’y Lamp Reflection Plate Angle Lamp Plug Angle Screw, x5 Screw, x3 CQ AX AT CL AK AE AA AA 6-23 6-24 6-25 6-26 6-27 6-28 6-29 6-30 6-31 6-32 6-33 6-34 6-35 6-36 6-37 6-38 6-39 6-40 6-41 9HN-9670-030607 9HN-9670-031007 NFANS0029CEZZ PSPAZ0426CEZZ PSPAZ0419CEZZ LX-EZ3011CEFD LANGK0783CEFW NFANS0006CE00 XBPSD30P18JS0 PDUC-0158CEKZ XEBSD30P08000 PSLDM3039CEFW LANGK0777CEFW PSLDM3040CEFW LX-BZ3266CEFD XBPSD40P16J00 XBPSD30P10JS0 9HN-3623-00 CMiR-0291CE01 J J J J J J J J J J J J J J J J J J J Screw, x2 Screw Exhaust Fan Exhaust Fan Spacer, x3 Exhaust Fan Bush, x3 Screw, x3 Color Wheel Fan Angle Color Wheel Fan Screw, x8 Lamp Duct Screw, x7 HDDE Shield A Socket Angle HDDE Shield B Screw, x3 Screw, x3 Screw, x2 Lamp Box Ass'y Color Wheel BC AB AC AC AH BB AA AM AA AT AF AX AA AA AA 156 XV-Z9000U/E OPTICS MECHANISM PARTS/ TEILE FÜR OPTIKMECHANISMUS H 6-19 6-20 6-21 G 6-8 6-15 6-16 6-16 6-7 6-31 6-12 6-6 6-36 6-41 6-39 6-11 6-9 6-34 6-14 F 6-13 6-2 6-10 6-18 6-38 6-17 6-31 6-37 E 6-29 6-33 6-5 6-30 6-33 6-33 6-35 6-4 6-32 6-33 6-27 6-5 6-25 6-28 6-26 6-5 6-4 6-3 6-1 6-5 6-27 D 6-26 6-26 6-22-1 6 6-40 6-22-7 6-24 C 6-23 6-22-2 6-22-3 6-22-6 6-22 B 6-22-6 6-22-4 6-22-6 6-22-7 6-22-5 6-22-7 6-22-6 A 6-22-6 1 2 3 4 157 5 6 XV-Z9000U/E Ref. No. Part No. ★ Description Code QACCU5013CEZZ QACCV4002CEZZ QACCB5024CENA J AC Cord (For US. and Canada) J AC Cord (For Europe) J AC Cord (For U.K. and Hong Kong) RRMCG1657CESA J R/C Unit UDSKA0047CEN1 J CD ROM TiNS-7416CEZZ J Operation Manual (XV-Z9000U) TiNS-7521CEZZ J Operation Manual 1 (XV-Z9000E) TiNS-7522CEZZ J Operation Manual 2 (XV-Z9000E) TiNS-7418CEZZ J CD ROM Manual (XV-Z9000U) TiNS-7523CEZZ J CD ROM Manual (XV-Z9000E) PCAPH1056CESA J Lens cap GCOVA1985CEKA J Terminal Cover TCAUZ3036CEZZ TGAN-1670CEZZ TGAN-1659CEZZ TCADH1018CEZZ — TCAUH1133CEZZ ★ Description Code (NOT REPLACEMENT ITEM) AX AZ AZ SPAKC5549CEZZ SPAKC5623CEZZ SPAKP0910CEZZ SPAKX2956CEN1 SPAKX2974CEZZ SPAKF0509CEZZ TLABK0001TAZZ BC AQ AV – – – – – – – Packing Case (XV-Z9000U) Packing Case (XV-Z9000E) Polystyrene Cover Buffer Material Buffer Material for Lens Sleeve(Box for Accessories) Number Card — — — — — — — BG BA SERVICE JIGS AP (Use for servicing) QCNW-5057CEZZ AP QCNW-5855CEZZ AW BA QCNW-A104WJZZ ACCESSORIES (NOT REPLACEMENT ITEM) TCAUZ3050CEZZ Part No. PACKING PARTS SUPPLIED ACCESSORIES å å å Ref. No. QCNW-A105WJZZ – Software Caution — (XV-Z9000U) – Software Caution — (XV-Z9000E) – Guarrantee card (for U.S.) — – Guarrantee card (for Canada) — – RCA-21pin Connector — Operation Manual (For Europe) – Two AA Size Batteries — – Caution card — (XV-Z9000U) 158 J Extension Cable 60-pin Main-PC I/F J Extension Cable 50-pin PC I/F-Formatter J Extension Cable 30-pin PC I/F-Formatter J Extension Cable 10-pin Main-Formatter CD AL XV-Z9000U/E Part No. ★ Description Ref. No. Part No. ★ Description PACKING OF THE SETCode / VERPACKEN DES GERÄTS Ref. No. Polystyrene Cover (SSAKA1109CEZZ) Terminal Cover (CCOVA1985CE01) Operation Manual (TiNS-7416CEZZ : XV-Z9000U) Operation Manual 1 (TiNS-7521CEZZ : XV-Z9000E) Operation Manual 2 (TiNS-7522CEZZ : XV-Z9000E) CD ROM Manual (TiNS-7418CEZZ : XV-Z9000U) (TiNS-7523CEZZ : XV-Z9000E) R/C Unit (RRMCG1657CESA) CD ROM (UDSKA0047CEN1) AC Cord ( QACCU5013CEZZ : For US. and Canada) (QACCV4002CEZZ : For Europe) (QACCB5024CENA : For U.K. and Hong Kong) Sleeve for Accessories (SPAKF0509CEZZ) Buffer material (SPAKF2956CEN1) Polystyrene Cover (SPAKP0910CEZZ) Lens Cap (PCAPH1075CESA) Buffer Material for Lens (SPAKX2974CEZZ) FRONT Packing Case (SPAKC5549CEZZ : XV-Z9000U) (SPAKC5623CEZZ : XV-Z9000E) Fix with craft tape. Fix with 6 staples. 159 Code XV-Z9000U/E COPYRIGHT © 2001 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. TQ1203-S Aug. 2001 Printed in Japan In Japan gedruckt D Japan P Japan SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan SY. KY 160