Download Viking Professional VCRB536RSS Installation guide
Transcript
Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.com UL F20604A EN C UL (070709J) All Refrigerator/Freezer Table of Contents IMPORTANT–Please Read and Follow! Warnings & Important Information _________________________________________________________ 3 Professional & Professional Integrated Dimensions & Specifications (30” & 36” Professional) _______________________________ 6 Dimensions & Specifications (30” & 36” Professional Integrated) _____________________ 8 Cutout Dimensions (30” Professional & Professional Integrated) _____________________ 10 Anti-Tip Dimensions (30” Professional & Professional Integrated) ____________________ 11 Cutout Dimensions (36” Professional & Professional Integrated) _____________________ 12 Anti-Tip Dimensions (36” Professional & Professional Integrated) _____________________ 13 Dimensions & Specifications (Dual Professional) ____________________________________ 14 Dimensions & Specifications (Dual Professional Integrated) ___________________________ 18 Cutout Dimensions (Dual 30” Professional & Professional Integrated) _________________ 22 Anti-Tip Dimensions (Dual 30” Professional & Professional Integrated) ________________ 23 Cutout Dimensions (Dual 30” & 36” Professional & Professional Integrated) ___________ 24 Anti-Tip Dimensions (Dual 30” & 36” Professional & Professional Integrated) __________ 25 Cutout Dimensions (Dual 36” Professional & Professional Integrated) _________________ 26 Anti-Tip Dimensions (Dual 36” Professional & Professional Integrated)_________________27 Cabinet Information (Professional) ________________________________________________ 28 Cabinet Information (Professional Integrated) ______________________________________ 30 Designer Dimensions & Specifications (30”& 36”) ___________________________________________ 32 Cutout Dimensions (30”)_________________________________________________________ 34 Anti-Tip (30”)___________________________________________________________________ 35 Cutout Dimensions (36”)_________________________________________________________ 36 Anti-Tip Dimensions (36”)________________________________________________________ 37 Dimensions & Specifications (Dual)________________________________________________ 38 Cutout Dimensions (Dual 30”) ____________________________________________________ 42 Anti-Tip Dimensions (Dual 30”) ___________________________________________________ 43 Cutout Dimensions (Dual 30” & 36”) ______________________________________________ 44 Anti-Tip Dimensions (Dual 30” & 36”) _____________________________________________ 45 Cutout Dimensions (Dual 36”) ____________________________________________________ 46 Anti-Tip Dimensions (Dual 36”) ___________________________________________________ 47 Cabinet Information_____________________________________________________________ 48 Custom Side Panel Dimensions (Professional) __________________________________________ 50 Custom Side Panel Dimensions (Designer & Professional Integrated) _____________________ 51 General Information ________________________________________________________________ 52 Unpacking & Moving ____________________________________________________________ 54 Installation_________________________________________________________________________ 55 Hinge Adjustment ______________________________________________________________ 56 Kickplate Installation ____________________________________________________________ 58 Door Stop Adjustment __________________________________________________________ 59 Final Installation ________________________________________________________________ 59 Performance Checklist ______________________________________________________________ 61 Control Panels _____________________________________________________________________ 62 Service & Registration_______________________________________________________________ 63 • Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, frequency, wattage, amperage, and phase is attached to the product. 2 Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. • To reduce the risk of fire, electric shock, or injury to persons, installation work and electrical wiring must be done by qualified people in accordance with all applicable codes and standards, including fire-rated construction. This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others. All safety messages will be preceded by the safety alert symbol and the word“DANGER” or “WARNING.”These words mean: • The installer should leave these instructions with the consumer who should retain them for local inspector’s use and for future reference. D A N G E R You will be killed or seriously injured if you don’t follow instructions. WARNING You can be killed or seriously injured if you don’t follow instructions. All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. 3 IMPORTANT–Please Read and Follow! IMPORTANT–Please Read and Follow! A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances. • The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of water or moisture. • Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below. It is your responsibility to: • comply with installation specifications and dimensions. • properly install unit. • remove any moldings or decorative panels that prevent the unit from being serviced. • make sure that you have these materials (not provided with your unit), which are necessary for proper installation: • 1/4” (6 mm) copper tubing with shutoff valve • 6– #8 x 3” (7.6 cm) wood screws (longer screws may be required) • 1– Saddle valve (do not use self-piercing feature of the valve) • assure that floor will support unit, door panels and contents (approximately 1200 pounds [540 kg]). • provide a properly grounded electrical outlet. • assure that location will permit appliance doors to open 90° minimum. If • • • • the use of a GFI is required, it should be: Of the receptacle type (breaker type or portable type NOT recommended) Used with permanent wiring only (temporary or portable wiring NOT recommended) On a dedicated circuit (no other receptacles, switches or loads in the circuit) Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT recommended) • Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard) • In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations) • Protected from moisture (water, steam, high humidity) as much as reasonably possible WARNING WARNING ELECTRICAL SHOCK HAZARD TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions. Disconnect power or turn power disconnect switch to OFF position before removing top grille. Failure to do so can result in death or electrical shock. Use two or more people to move and install appliance. Failure to do so can result in death or serious injury. Most of the unit’s weight is at the top. Extra care is needed when moving the unit to prevent tipping. Use cardboard shipping material or plywood under unit until it is installed in the operating position to protect floor surface. 4 5 Dimensions Specifications 30” Professional 30” Professional Description 29” (73.7 c m 3–19/ 30” Overall width Overall height from bottom Overall depth from rear ) (76.2 c m) 3 (9.1 cm2” ) 36” Professional 9–5/3 2” (2 Cutout width Cutout height Cutout depth Electrical requirements 3.3 cm ) 35” (88.9 c 3–19/ 36” (91.5 c m) 32” (9.1 cm m) )) Maximum amp usage Inlet water requirements 9–5/3 (23 2” .3 cm) 82–3 (210. /4” 2 cm min. ) to 75–1 (192 5/16” .9 cm ) /4” 27–1cm) 84–1 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with grounded 3-prong plug attached to product 9.1 amps 5.7 amps 1/4” copper tubing inlet waterline; minimum 20 psi; N/A maximum 120 psi 15.9 cu. ft. (450 liters) Approximate shipping weight 530 lbs. (238.5 kg) / 18.2 cu. ft. (516 liters) 505 lbs. (227.3 kg) 36” Professional Description 82–3 75–1 (192 5/16” . 9 cm ) (210. /4” 2 cm min. ) to /4” 27–1cm) 84–1 4” –3/cm) 0 2 .7 (52 6” 3/1m) – 226.4 c (5 6” 1/1m) 1 – 24 .7 c Overall width Overall height from bottom Overall depth from rear / (213. 16” 5 cm max. ) (69.2 Cutout width Cutout height Cutout depth Electrical requirements Maximum amp usage Inlet water requirements (62 /4” 0–3cm) VCFB536 VCRB536 36” (91.5 cm) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. To front edge of side trim: 22-3/16” (56.4 cm) To front of top grille: 24-11/16” (62.7 cm) To front of handle endcap: 27-1/4” (69.2 cm) 35-1/2” (90.2 cm) min. to 35-3/4” (90.8 cm) max. 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. 24” (61.0 cm) min. 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with grounded 3-prong plug attached to product 9.5 amps 6.5 amps 1/4” copper tubing inlet waterline; minimum 20 psi; N/A maximum 120 psi Overall interior dimensions Total capacity 19.1 cu. ft. (541 liters) 22.8 cu. ft. (646 liters) Approximate shipping weight 585 lbs. (263.3 kg) 570 lbs. (256.5 kg) 2 .7 52 ( ” /16 –3 cm) 2 2 6.4 (5 6” 1/1m) 1 – 24 .7 c (62 6 VCRB530 30” (76.2 cm) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. To front edge of side trim: 22-3/16” (56.4 cm) To front of top grille: 24-11/16” (62.7 cm) To front of handle endcap: 27-1/4” (69.2 cm)) 29-1/2” (74.9 cm) min. to 29-3/4” (75.6 cm) max. 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. 24” (61.0 cm) min. Overall interior dimensions Total capacity (213. 16” 5 cm max. ) (69.2 VCFB530 7 Dimensions Specifications 30” Professional Integrated 30” Professional Integrated Description Overall width 29” (73.7 c m 3–19/ 30” Overall height from bottom Overall depth from rear ) (76.2 c m) 3 (9.1 cm2” ) Cutout width Cutout height Cutout depth Electrical requirements 36” Professional Integrated 9–5/3 2” (2 3.3 cm ) 35” (88.9 c 3–19/ 36” m) Maximum amp usage Inlet water requirements (91.5 c m) 3 (9.1 cm2” )) 9–5/3 (23 2” .3 cm) 82–3 (210 /4” (192 5/16” .9 cm ) /2” 26–1cm) 84–1 grounded 3-prong plug attached to product 9.1 amps 5.7 amps 1/4” copper tubing inlet waterline; minimum 20 psi; N/A maximum 120 psi 15.9 cu. ft. (450 liters) 530 lbs. (238.5 kg) Description 75–1 (192 5/16” . 9 cm ) 82–3 (210 /4” .2 cm min. ) to /2” 26–1cm) 84–1 / (213. 16” 5 cm max. ) (67.3 4” –3/cm) 0 2 Overall height from bottom Overall depth from rear Cutout width Cutout height Cutout depth Electrical requirements Maximum amp usage Inlet water requirements .7 ” 3/8 ) – 23 .4 cm (59 ” 24 cm) .0 (61 /4” 0–3cm) VIFB536 505 lbs. (227.3 kg) Overall interior dimensions Total capacity 19.1 cu. ft. (541 liters) 22.8 cu. ft. (646 liters) Approximate shipping weight 585 lbs. (263.3 kg) 570 lbs. (256.5 kg) ( /8” –3cm) 3 2 .4 (59 ” 24 cm) (61 VIRB536 36” (91.5 cm) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. To front edge of side trim: 23-3/8” (59.4 cm) To front of top grille: 24” (61.0 cm) To front of handle endcap: 26-1/2” (67.3 cm) 36” (91.4 cm) 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. 24” (61.0 cm) min. 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with grounded 3-prong plug attached to product 9.5 amps 6.5 amps 1/4” copper tubing inlet waterline; minimum 20 psi; N/A maximum 120 psi 2 .7 52 8 18.2 cu. ft. (516 liters) 36” Professional Integrated Overall width (52 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with Approximate shipping weight / (213. 16” 5 cm max. ) (67.3 VIRB530 30” (76.2 cm) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. To front edge of side trim: 23-3/8” (59.4 cm) To front of top grille: 24” (61.0 cm) To front of handle endcap: 26-1/2” (67.3 cm) 30” (74.9 cm) 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. 24” (61.0 cm) min. Overall interior dimensions Total capacity .2 cm min. ) to 75–1 VIFB530 .0 9 Cutout Dimensions Anti-Tip Dimensions 30” Professional & Professional Integrated 30” Professional & Professional Integrated 24” ) m c (61.0 See An ti-Tip b oard in stallatio n Electric Outlet Location Professional Anti-Tip Location 6” (15.2 c m) Two 2”x 4” mounting boards 3” (7.6 cm) x 3-1/2” (8.9 cm) 9” (22.9 cm) 9” (22.9 3” ) m c m) (7.6 c 23” (58.4 c m) 82 (210 –7/8” .5 anti- cm) mi tip b n. oa o peni ng 3– 1/ (8 2” ) min to bo . anti- ttom of tip b oard 84 enin r g he d & ight ) / .6 cm8” (201 rd & h e ig ht (213 –1/16” .5 anti- cm) m t a op ip boa x. .9 cm 79–3 80 (204 –1/2” .6 to bo cm) max . ttom a 73–3 (18 /8” NOTE: If unit is installed deeper than 24” (61.0 cm),then shim behind the mounting board by the difference. nti-ti o p bo f ard 6.4 cm ) Water Line Entry Area Note: Shown for All Freezer Only 30 ” ( Prof essio76.2 cm) nal I nteg rate d (74. 29–1 9c /2 (75. 29-3 to m) min”. 6 cm /4” ) ma Pro x. fe (7 30 Mosdsional6.2 cm”) els O Integ nly rate d 5/8 (1 .5 ” cm) 7–5 (19. /8” 29–1 (74.9 /2” Mod els cm) Only One 2”x 4” mounting board 1–1/2” (3.8 cm) x 3-1/2” (8.9 cm) 4 cm 6–3/ ) (1 4 7.1 c ” m) 3” (7.6 c m) 2” 1–1/ m) (3.8 c 23” 5/8 (1 .5 ” cm) 3 (9.2 –5/8” cm) 1 (27. 0–3/4 3 cm) ” p waO ter tiona line l flo ent or ry 10 Professional Integrated Anti-Tip Location 10–1 (26.7 (58.4 c m) 1” 3– 1/ (8 2” cm) (2 .5 .9 cm ) / cm)2” (1.5 5/8” cm ) Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board. NOTE: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting board by the difference. 11 Cutout Dimensions Anti-Tip Dimensions 36” Professional & Professional Integrated 24” ) cm (61.0 See An ti-Tip b oard in stallatio n 36” Professional & Professional Integrated Electric Outlet Location Professional Anti-Tip Location 6” (15.2 c m) Two 2”x 4” mounting boards 3” (7.6 cm) x 3-1/2” (8.9 cm) 9” (22.9 cm) 9” (22.9 3” ) c m) m (7.6 c 29–1/2 ” (74.9 c m) 82 (210 –7/8” .5 anti- cm) mi tip b n. 3– 1/ (8.9 2” c m) oa open ing h rd & eigh t 79–3 (201 84 (213 –1/16” .5 anti- cm) m t a op ip boa x. enin r g he d & ight /8” .6 to bo cm) min . anti- ttom of tip b oard 80 (204 –1/2” .6 to bo cm) max . ttom a 73–3 (18 /8” 6.4 cm ) NOTE: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting board by the difference. nti-ti o p bo f ard Water Line Entry Area Note: Shown for All Freezer Only Professional Integrated Anti-Tip Location 3 6” Prof essio(91.4 cm ) nal I nteg rate d (90. 35–1 2 cm /2 (90. 35-3 to ) min”. 8 cm /4” Pro ) ma fe (9 36 x. M ssion 1.4 c ” ode al In m) ls O tegr nly ate d 5/8 (1 .5 ” cm) 7–5 (19. /8” 35–1 (90.2 /2” cm) One 2”x 4” mounting board 1–1/2” (3.8 cm) x 3–1/2” (8.9 cm) 4 cm 6–3/ ) (1 4 7.1 c ” m) 3” (7.6 c m) 2” 1–1/ m) (3.8 c 29–1/2 ” (74.9 c m) 5/8 (1 ” 3 (9 –5/8 . 2 cm ” ) .5 cm ) 1 (27. 0–3/4 3 cm) ” p waO ter tiona line l flo ent or ry 12 Mod els O nly 10–1 (26.7 / cm)2” 3– 1/ (8.9 2” 1” ) cm c m) (2 .5 (1.5 5/8” cm ) Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height. Note: Top of unit must b e placed firmly under anti-tip board. 13 NOTE: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting board by the difference. Dimensions Dimensions Dual 30” & 36” Professional Dual 30” Professional 2 9” 29” (73.7 c 30” 3–19/ 32 ” (76.2 c m) m) 30” (7 (9.1 cm ) 3–19/ 3 (9.1 2” 29” (73.7 c m) 6.2 cm ) 16 .9 cm” ) 82–3 (69.2 1” (91.5 c m) 9–5/3 (23 2” .3 cm) 75–1 (192 5/16” .9 82–3 cm ) (210. /4” 2 cm min. ) to 84–1 / 16 ” (213. 5 cm max. ) 4” 27–1/cm) (2 Bet .54 cm wee n U) nits 36” 4” –3/cm) 0 2 .7 (52 6” 3/1m) – 226.4 c (5 6” 1/1m) 1 – 24 2.7 c (69.2 4” –3/cm) 0 2 .7 (52 6” 3/1m) – 226.4 c (5 6” 1/1m) 1 – 24 .7 c 1 (2 ” Bet .54 cm wee n U) nits (62 15 / (213. 16” 5 cm max. ) 4” 27–1/cm) (6 14 35” (88.9 c m) m) (210. /4” 2 cm min. ) to 84 – 1 ) 2” (23.3 c (192 (76.2 c m) cm) 9–5/3 75–1 5/ (73.7 c m 30 ” Dimensions Specifications Dual Professional* Dual 36” Professional Description Overall width Overall height from bottom Overall depth from rear 35” 3–19/ (88.9 c m) 36” 3 (9.1 cm2” ) (91.5 c m) 35” (88.9 c m) 36” (91.5 c m Cutout width Cutout height Cutout depth Electrical requirements ) 9–5/3 2 (23.3 c ” m) Maximum amp usage Inlet water requirements (All Freezer only) (2) 30” Units Approximate shipping weight 82–3 cm) (210. /4” 2 cm min. ) to grounded 3-prong plug attached to product 30” Freezer 9.1 amps per unit 30” Refrigerator 5.7 amps per unit 36” Freezer 9.5 amps per unit 36” Refrigerator 6.5 amps per unit 1/4” copper tubing inlet waterline; minimum 20 psi; maximum 120 psi 15.9 18.2 19.1 22.8 4” –3/cm) 0 2 .7 (52 6” 3/1m) – 226.4 c (5 6” 1/1m) 1 4– 7 c 1 (2 ” Bet .54 cm wee ) nu nits 2 2. (6 16 ft. ft. ft. ft. (450 (516 (541 (646 liters) liters) liters) liters) *For installation of two units side-by-side, a separate grille kit accessory must be purchased. 84–1 / c (69.2 cu. cu. cu. cu. 30”- Freezer 530 lbs. (238.5 kg) each; Refrigerator 505 lbs. (227.3 kg) each 36”- Freezer 585 lbs. (263.3 kg) each; Refrigerator 570 lbs. (256.5 kg) each (213. 16” 5 cm max. ) 4” 27–1/ m) (2) 36” Units (2) 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with Overall interior dimensions 30” Freezer 30” Refrigerator 36” Freezer 36” Refrigerator 75–1 (192 5/16” .9 (1) 36” & (1) 30” Unit 60” (152.4 cm) 66” (167.6 cm) 72” (182.9 cm) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. To front edge of side trim: 22-3/16” (56.4 cm) To front of top grille: 24-11/16” (62.7 cm) To front of handle endcap: 27-1/4” (69.2 cm) 59-1/2” (151.1 cm) 65-1/2” (166.4 cm) 71-1/2” (181.6 cm) 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. 24” (61.0 cm) min. 17 Dimensions Dimensions Dual 30” Professional Integrated Dual 30” & 36” Professional Integrated 2 9” 29” (73.7 c 30” 3–19/ 32 ” (76.2 c m) m) 30” (7 (9.1 cm ) 3–19/ 3 (9.1 2” 29” (73.7 c m) 6.2 cm ) 16 .9 cm” ) 36” (91.5 c m) (23.3 c2” m) m) 82–3 75–1 (192 5/16” .9 82–3 cm ) (210. /4” 2 cm min. ) to 84–1 /16” (213. 5 cm max. ) 2” 26–1/cm) (67.3 (67.3 4” –3/cm) 0 2 .7 (52 .7 (52 1 (2.5 ” Bet 4 cm wee n U) nits 18 (59 ” 24 m) c .0 (61 /8” –3cm) 3 2 .4 1 (2 ” Bet .54 cm wee n U) nits (59 ” 24 cm) .0 (61 19 / (213. 16” 5 cm max. ) 2” 26–1/cm) 4” –3/cm) 0 2 /8” –3cm) 3 2 .4 35” (88.9 c m) 9–5/3 (210. /4” 2 cm min. ) to 84–1 ) 2” (23.3 c (192 (76.2 c m) cm) 9–5/3 75–1 5/ (73.7 c m 30 ” Dimensions Specifications Dual Professional Integrated* Dual 36” Professional Integrated 3–19/ 36” 3 (9.1 cm2” ) (91.5 c m) 36” (2) 30” Units Overall width 60” (152.4 cm) 66” (167.6 cm) 72” (182.9 cm) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. To front edge of side trim: 23-3/8” (59.4 cm) To front of top grille: 24” (61.0 cm) To front of handle endcap: 26-1/2” (67.3 cm) 60” (152.4 cm) 66” (167.6 cm) 72” (182.9 cm) 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. 24” (61.0 cm) min. Overall height from bottom Overall depth from rear 35” (88.9 c m) Description 35 ” (88.9 c m) (91.5 c m) Cutout width Cutout height Cutout depth Electrical requirements 9–5/3 2 (23.3 c ” m) Maximum amp usage Inlet water requirements (All Freezer only) (192 Approximate shipping weight 5/16 .9 cm” ) 82–3 (210. /4” 2 cm min. ) to grounded 3-prong plug attached to product 30” Freezer 9.1 amps per unit 30” Refrigerator 5.7 amps per unit 36” Freezer 9.5 amps per unit 36” Refrigerator 6.5 amps per unit 1/4” copper tubing inlet waterline; minimum 20 psi; maximum 120 psi 15.9 18.2 19.1 22.8 /4”) 3 – 0 cm 2 .7 52 ( 1 (2.5 ” ” 3/8m) – 3 c 2 .4 59 Bet 4 cm wee ) nu nits ( ” 24 cm) .0 (61 20 ft. ft. ft. ft. (450 (516 (541 (646 liters) liters) liters) liters) *For installation of two units side-by-side, a separate grille kit accessory must be purchased. 84–1 / (67.3 cu. cu. cu. cu. 30”- Freezer 530 lbs. (238.5 kg) each; Refrigerator 505 lbs. (227.3 kg) each 36”- Freezer 585 lbs. (263.3 kg) each; Refrigerator 570 lbs. (256.5 kg) each (213. 16” 5 cm max. ) 2” 26–1/cm) (2) 36” Units (2) 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with Overall interior dimensions 30” Freezer 30” Refrigerator 36” Freezer 36” Refrigerator 7 5– 1 (1) 36” & (1) 30” Unit 21 Cutout Dimensions Anti-Tip Dimensions Dual 30” Professional & Professional Integrated See An ti-Tip b oard in stallatio n 24” ) .0 cm (61 Dual 30” Professional & Professional Integrated Electric Outlet Location Professional Anti-Tip Location 6” (15.2 c m) 9” (22.9 Two 2”x 4” mounting boards per unit 3” (7.6 cm) x 3–1/2” (8.9 cm) 9” (22.9 cm) c m) 23” (58.4 c m 8 (210 2–7/8” .5 c m) m antit openip boardin. ing h & eigh t 73–3 (186.4/8” cm) 79 (201 –3/8” .6 to bo cm) min . / .5 cm16” .9 cm 80 Water Line Entry Area Prof essio 7 –5/ (19.4 8” 6–3 / cm) (17.1 4” cm) (1.5 c m) 3” (7.6 cm) 5/8” ) 1 (27. 0–3/4 3 cm ” ) nti-ti o p bo f ard Professional Integrated Anti-Tip Location 6 0” nal I(152.4 cm nteg rate ) d Mo dels 59–1 Only (151. /2” 1 cm ) One 2”x 4” mounting board per unit 1–1/2” (3.8 cm) x 3–1/2” (8.9 cm) 5/8 (1.5 c” m) 3 (9.2 –5/8” cm 23” (58.4 c m) 1 – (26.0 7 c1m/2” ) p waO tertiona line l flo ent or ry ) Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the anti-tip bracket by the difference. (204 –1/2” .6 to bo cm) max . ttom a Note: Cutout opening shown with All Freezer model on left. Reverse water line entry if All Freezer model is on right. (1559–1 23” 3 –1 / (8 2” anti- ttom of tip b oard anti)m t ope ip boardax. ning heig & ht 1.1 /2” c m) Pro fess (152 60” i Mod onal .4 cm els OInte ) nly grate d 3” m) (7.6 c (58.4 c m) 84–1 (213 ) (1.55/8” c m) 2” 1–1/ m) (3.8 c 23” (58.4 c m) 1” cm) (2.5 Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height. 3 –1 / (8 2” Note: Top of unit must b e placed firmly under anti-tip board. .9 cm ) Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the anti-tip bracket by the difference. 22 23 Cutout Dimensions Anti-Tip Dimensions Dual 30” & 36” Professional & Professional Integrated Dual 30” & 36” Professional & Professional Integrated See An ti-Tip b oard in stallatio n 24” ) .0 cm (61 Electric Outlet Location Professional Anti-Tip Location 6” (15.2 c m) 9” (22.9 cm 9” (22.9 ) Two 2”x 4” mounting boards per unit 3” (7.6 cm) x 3 1/2” (8.9 cm) c m) 82 (210 –7/8” .5 anti- cm) mi tip n. open board & ing h eigh t 29” (73.7 c m) 79 (201 –3/8” .6 to bo cm) min . 73–3 (186.4/8” cm) ning oard & heig ht 7 Prof 66” essio nal I (167.6 cm nteg rated) Mo –5/ (19.4 8” 6–3 / cm) 5/8 (17.1 4” cm) (1.5 c” m) 3” (7.6 cm) 65–1 (166. /2” 4 cm ) Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards by the difference. nti-ti p bo of ard Note: Cutout opening shown with All Freezer model on left. Reverse water line entry if All Freezer model is on right. Pro fe (1 Mosdsiona6l7.6 cm” els OInte ) nly grate d (8.9 c2” m) (204 –1/2” .6 to bocm) max . ttom a Water Line Entry Area Professional Integrated Anti-Tip Location dels On ly One 2”x 4” mounting board per unit 1–1/2” (3.8 cm) x 3–1/2” (8.9 cm) 5/8 (1.5 c” m) 3 (9.2 –5/8” cm ) 1 (27. 0–3/4 3 cm ” ) 29” p waO tertiona line l flo ent or ry 2” 1–1/ m) (73.7 c m) 1 – (26.0 7 c1m/2” ) (1.55/8” c m) 1” (2.5 c m) (3.8 c Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height. 23” (58.4 c Note: Top of unit must be placed firmly under anti-tip board. Note: Dimensions shown for 36” AF/AR model on the left. Reverse mounting boards if units are installed on the right. 3–1/ (8.9 c2” m) Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards by the difference. 24 m) 3–1/ 80 o pe 23” (58.4 c anti- ttom of tip b oard 84 (213 –1/16” .5 anti- cm) m tip b ax. (16665–1/2 .4 cm ” ) 66 3” m) (7.6 c 25 m) Cutout Dimensions Anti-Tip Dimensions Dual 36” Professional & Professional Integrated See An ti-Tip b oard in stallatio n 24” ) .0 cm (61 Dual 36” Professional & Professional Integrated Electric Outlet Location Professional Anti-Tip Location 6” (15.2 c m) 9” (22.9 cm Two 2”x 4” mounting boards per unit 3” (7.6 cm) x 3–1/2” (8.9 cm) 9” (22.9 ) c m) 29” (73.7 c m) 82–7 / (210 . 5 8” anti- cm) mi tip n. open board & ing h eigh t 84–1 (213 /8” (201 .6 to bo cm) min . anti- ttom of tip b oard ) / .5 16” anti- cm) m tip b ax. .9 cm /2” (204 .6 to bocm) max . ttom a ning oard & heig ht ) Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards by the difference. nti-ti p bo of ard Water Line Entry Area ) 3–1/ (8 2” 80–1 o pe 29” (73.7 c m 79–3 73–3 (18 /8” 6.4 cm 3” ) m (7.6 c Note: Cutout opening shown with All Freezer model on left. Reverse water line entry if All Freezer model is on right. Professional Integrated Anti-Tip Location 7 –5/ (19.4 8” 6–3 / cm) 5/8” (17.1 4” cm) (1.5 c m) 3” (7.6 cm) (1871–1 1.6 /2” Pro cm) fess (182 72” Modional .8 cm els OInte ) nly grate d 72” Prof essio ( nal I 182.8 cm nteg rate ) dM 71–1 odel s (181. /2” 6 cm ) One 2”x 4” mounting board per unit 1–1/2” (3.8 cm) x 3–1/2” (8.9 cm) Only 5/8 29” (1.5 c” m) 3 (9.2 –5/8” cm ) 1 (27. 0–3/4 3 cm ” ) 1 –1 (26.0 7 cm/2” p waO tertiona line l flo ent or ry ) (73.7 c m) 2” 1–1/ m) (3.8 c 29” (73.7 c m (1.55/8” c m) 1” (2.5 cm) Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board. 3–1/ (8 2” .9 cm ) Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards by the difference. 26 27 ) Cabinet Information Cabinet Information (Professional) Professional models fit “semi-flush” in standard 24” (61.0 cm) deep cabinet openings. The door face protrudes 2-1/2” (6.4 cm) from the cabinet face. The handle protrudes an additional 2-1/2” (6.4 cm) into the room. (Professional) Professional models fit “semi-flush” in standard 24” (61.0 cm) deep cabinet openings. The door face protrudes 2-1/2” (6.4 cm) from the cabinet face. The handle protrudes an additional 2-1/2” (6.4 cm) into the room. Top View Top View Wall Wall 1–13/16” 1–13/16” (4.6 cm) Space if 24” (61.0 cm) standard cabinet depth is used (4.6 cm) Space if 24” (61.0 cm) standard cabinet depth is used 24” 24” (61.0 cm) Standard cabinet depth 3/4” (61.0 cm) Standard cabinet depth 3/4” (1.9 cm) Full end panel (1.9 cm) Full end panel Partial overlay cabinet door Countertop overhang Door Door 2–1/2” 2–1/2” (6.4 cm) Offset Top View (6.4 cm) Offset Wall 1–13/16” 24” (61.0 cm) Standard cabinet depth (4.6 cm) Space if 24” (61.0 cm) standard cabinet depth is used 3/4” (1.9 cm) Full end panel 5–16” (0.8 cm) Door 2–1/2” (6.4 cm) Offset 28 29 Cabinet Information Cabinet Information (Professional Integrated) Professional Integrated models fit flush in standard 24” (61.0 cm) deep cabinet openings with no protrusion into the room except the handle protrudes 2-1/2” (6.4 cm) into the room. (Professional Integrated) Professional Integrated models fit flush in standard 24” (61.0 cm) deep cabinet openings with no protrusion into the room except the handle protrudes 2-1/2” (6.4 cm) into the room. Top View Overlapping cabinet doors Top View Wall Wall 3/4” (1.9 cm) space if 24” (61.0 cm) standard cabinet depth is used 1” (2.5 cm) space if 25” (63.5 cm) cabinet depth is used 25” (63.5 cm) countertop depth 3/4” (1.9 cm) Full end panel 24” 24-3/4” (62.9 cm) 3/4” (61.0 cm) Standard cabinet depth (1.9 cm) Full end panel 24” (61.0 cm) Standard cabinet depth Cabinet door Door Door Flush Flush Top View Top View Flush mount cabinet doors Wall Wall 1” 1” (2.5 cm) space if 25” (63.5 cm) cabinet depth is used 25” (63.5 cm) (2.5 cm) space if 25” (63.5 cm) cabinet depth is used 3/4” 3/4” (1.9 cm) Full end panel 25” (63.5 cm) Cabinet depth (1.9 cm) Full end panel Door Cabinet door Door Flush Flush 30 31 Dimensions Specifications 30” Designer 30” Designer Description 29” 30” (73.7 c m) Overall height from bottom Overall depth from rear (76.2 c m) 3–1/2 ” (8.9 cm Overall width ) 9 –5 /3 36” Designer 2 (23.3 c ” m) Cutout width Cutout height Cutout depth Electrical requirements 35” 36” 3–1/2 ” (88.9 c m) (91.5 c m) (8.9 cm ) Maximum amp usage Inlet water requirements 9 –5 /3 (23.3 c2” m) 82–3 (210. /4” 2 cm min. ) to 75–1 5 (192 /16” .9 cm ) 84–1 /2” 26-1 cm) 525 lbs. (236.3 kg) 18.2 cu. ft. (516 liters) 495 lbs. (222.8 kg) 36” Designer 82–3 75–1 (192 5/16” .9 cm ) (210. /4” 2 cm min. ) to /2” 26-1 cm) 84–1 4” –3/cm) 0 2 .7 Overall width Overall height from bottom Overall depth from rear / (213. 16” 5 cm max. ) (67.3 Cutout width Cutout height Cutout depth Electrical requirements Maximum amp usage Inlet water requirements /8 ” –3 ) 23 cm .4 (59 ” 24 cm) (61 grounded 3-prong plug attached to product 9.1 amps 5.7 amps 1/4” copper tubing inlet waterline; minimum 20 psi; N/A maximum 120 psi 15.9 cu. ft. (450 liters) Description (52 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with Approximate shipping weight / DDRB530 30” (76.2 cm) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. To front edge of side trim: 23-3/8” (59.4 cm) To front of top grille: 24” (61.0 cm) To front of handle: 26-1/2” (67.3 cm) 30” (76.2 cm) 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. 24” (61.0 cm) min. Overall interior dimensions Total capacity (213. 16” 5 cm max. ) (67.3 DDFB530 .0 4” –3/ ) 20 cm DDFB536 Overall interior dimensions Total capacity 19.1 cu. ft. (541 liters) 22.8 cu. ft. (646 liters) Approximate shipping weight 580 lbs. (261.0 kg) 555 lbs. (249.8 kg) .7 (52 /8” –3cm) 3 2 (59 .4 ” 24 c m ) (61 32 DDRB536 36” (91.5 cm) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. To front edge of side trim: 23-3/8” (59.4 cm) To front of top grille: 24” (61.0 cm) To front of handle: 26-1/2” (67.3 cm) 36” (91.5 cm) 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. 24” (61.0 cm) min. 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with grounded 3-prong plug attached to product 9.5 amps 6.5 amps 1/4” copper tubing inlet waterline; minimum 20 psi; N/A maximum 120 psi .0 33 Cutout Dimensions Anti-Tip Dimensions 30” Designer 30” Designer 24” ) cm (61.0 See An ti-Tip b oard in stallatio n Electric Outlet Location 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm) 9” (22.9 c m) 79 (201 –3/8” .6 to cm) m 82 (210 –7/8” .5 c m) m antiin ti open p board . & in g h eigh t 84 ar g he d & ight ( 3. 8 c 23” (58.4 c m) 80 (204 –1/2” .6 to bocm) max . ttom a (213 –1/16” .5 anti- cm) m tip b ax. o o peni n 2” 1–1/ m) in. bo anti- ttom of tip b oard nti-ti p bo of ard 3–1/ (8. 2” 9 cm ) 73–3 (186.4/8” cm) Water Line Entry Area Note: Shown for All Freezer Only 30 7–5 (76.2 ” cm) (19.4/8” 6 –3 cm) 5/8” (17.1/4” (1 .5 cm) cm) 3” (7.6 c m) (76. 30” 2 cm ) One 2”x 4” mounting board 1–1/2” (3.8 cm) x 3–1/2” (8.9 cm) Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards by the difference. 5/8 (1 .5 ” cm) 3 (9.2 –5/8” cm) 1 (27. 0–3/4 3 cm) ” 10–1 (26.7 1” ) cm (2 .5 Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board. / cm)2” (1.5 5/8” cm ) p waO ter tiona line l flo ent or ry 34 35 Cutout Dimensions Anti-Tip Dimensions 36” Designer 36” Designer 24” ) m c (61.0 See An ti-Tip b oard in stallatio n Electric Outlet Location 6” (15.2 Anti-Tip Location c m) 9” (22.9 cm) 9” (22.9 c m) 79 (201 –3/8” .6 to cm) m 82 (210 –7/8” .5 c rd & h e ig ht 84 ar g he d & ight 29” (73.7 c m) 80 (204 –1/2” .6 to bocm) max . ttom a (213 –1/16” .5 anti- cm) m tip b ax. o o peni n ( 3. 8 c in. bo anti- ttom of tip b oard m antitip b ) min. oa o peni ng 2” 1–1/ m) nti-ti p bo of ard 3–1/ (8. 2” 9 cm ) 73–3 (186.4/8” cm) Water Line Entry Area Note: Shown for All Freezer Only 36 5/8 (1 .5 ” cm) (91. 36” 5 cm ) 7–5 (19. /8” (91.5 ” cm) 4 cm 6–3/ ) (1 4 7.1 c ” m) 3” (7.6 c m) One 2”x 4” mounting board 1–1/2” (3.8 cm) x 3–1/2” (8.9 cm) Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards by the difference. 5/8 (1 .5 ” cm) 3 (9.2 –5/8” cm) 1 (27. 0–3/4 3 cm ” ) Note: Top of unit must be placed firmly under anti-tip board. (2 .5 1 (26.70–1/2” cm ) Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height. 1” ) cm (1.5 5/8” cm ) p waO ter tiona line l flo ent or ry 36 37 Dimensions Dimensions Dual 30” & 36” Designer Dual 30” Designer 29 ” 29” (73.7 c m (73.7 c m) ) 29” 30” 3–1/2 (8.9 cm” ) (76.2 c m 3–1/2 ” (73.7 c m) ) (8.9 cm ) 30” 35” 30 ” (88.9 c m) (76.2 c m) 36” (91.5 c m) (76.2 c m) 9–5/3 9–5/3 (23 2” (23.3 c2” m) .3 cm) 75–1 5/ (192 16” .9 82–3 cm ) (210. /4” 2 cm min. ) to / 2” 26-1 cm) 84–1 (67.3 75–1 (192 5/16” .9 82–3 cm) / 2” 26-1 cm) (67.3 / (213. 16” 5 cm max. ) 1 (2 ” Bet .54 cm wee n U) nits 38 .7 /8” –3cm) 3 2 .4 ( 59 ” 24 cm) .0 (61 84–1 . (52 /8” –3 cm) 3 2 .4 1 (2 ” Bet .54 cm wee ) nu nits (5 9 ” 24 cm) .0 (61 39 / (213. 16” 5 cm max. ) /4” –3cm) 0 2 7 4” –3/ ) 2 0 cm (52 (210. /4” 2 cm min. ) to Dimensions Specifications Dual Designer* Dual 36” Designer 35 ” (88.9 c m) 3–1/2 (8.9 cm” ) 35 ” 36 ” (2) 30” Units Overall width 60” (152.4 cm) 66” (167.6 cm) 72” (182.9 cm) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. To front edge of side trim: 23-3/8” (59.4 cm) To front of top grille: 24” (61.0 cm) To front of handle: 26-1/2” (67.3 cm) 60” (152.4 cm) 66” (167.6 cm) 72” (182.9 cm) 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. 24” (61.0 cm) min. Overall height from bottom Overall depth from rear (88.9 c m) (91.4 c m) Description 36 ” (91.4 c m) 9–5/3 2” (23.3 c m) Cutout width Cutout height Cutout depth Electrical requirements Maximum amp usage Inlet water requirements (All Freezer only) (192 5/16” .9 cm ) 82–3 (210 /4” .2 cm min. ) to / 2” 26-1 ) cm (67.3 84– 1 Approximate shipping weight grounded 3-prong plug attached to product 30” Freezer 9.1 amps per unit 30” Refrigerator 5.7 amps per unit 36” Freezer 9.5 amps per unit 36” Refrigerator 6.5 amps per unit 1/4” copper tubing inlet waterline; minimum 20 psi; maximum 120 psi 15.9 18.2 19.1 22.8 1 ft. ft. ft. ft. (450 (516 (541 (646 liters) liters) liters) liters) *For installation of two units side-by-side, a separate grille kit accessory must be purchased. / (213. 16” 5 cm max. ) (59 ” 24 cm) .0 (61 40 cu. cu. cu. cu. 30” Freezer 525 lbs. (236.3 kg) each; Refrigerator 495 lbs. (222.8 kg) each 36” Freezer 580 lbs. (261.0 kg) each; Refrigerator 555 lbs. (249.8 kg) each /4” –3cm) 0 2 .7 (52 ” /8 –3cm) 3 2 .4 (2 ” Bet .54 cm wee ) nu nits (2) 36” Units (2) 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with Overall interior dimensions 30” Freezer 30” Refrigerator 36” Freezer 36” Refrigerator 75 – 1 (1) 36” & (1) 30” Unit 41 Cutout Dimensions Anti-Tip Dimensions Dual 30” Designer Dual 30” Designer See An ti-Tip b oard in stallatio n 24” ) .0 cm (61 Electric Outlet Location 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm 9” (22.9 ) c m) 82 (210 –7/8” .5 anti- cm) mi tip b n. oa o penin rd g he & ight 79 (201 –3/8” .6 to bo cm) min . anti- ttom of tip b oard 73–3 (18 /8” 6.4 cm ) 23” 80 84–1 (58.4 c m) (204 –1/2” .6 to bocm) max . ttom a / (213 .5 cm16” a nti-t ) ma ope ip board x. ning heig & ht 2” 1–1/ m) (3.8 c nti-ti p bo of ard 23” (58.4 c m) Water Line Entry Area 3–1/ (8. 2” Note: Cutout opening shown with All Freezer model on left. Reverse water line entry if All Freezer model is on right. 7 –5/ (19.4 8” 6–3 / cm) 5/8 (17.1 4” cm) (1.5 c” m) 3” (7.6 cm) (152 60” .4 cm ) 3 (9.2 –5/8” cm 1 (27. 0–3/4 3 cm ” ) 60 One 2”x 4” mounting board per unit 1–1/2” (3.8 cm) x 3–1/2” (8.9 cm) 5/8” Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards by the difference. m) 1 – (26.0 7 c1m/2” ) p waO tertiona line l flo ent or ry 42 ) (152. ” 4 cm ) (1.5 c ) 9 cm (1.55/8” c m) 1” cm (2.5 Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board. ) 43 Cutout Dimensions Anti-Tip Dimensions Dual 30” & 36” Designer See An ti-Tip b oard in stallatio n 24” ) .0 cm (61 Dual 30” & 36” Designer Electric Outlet Location 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm 9” (22.9 ) c m) 82 (210 –7/8” .5 anti- cm) mi tip n. open board & ing h eigh t 79 (201 –3/8” .6 to cm) m in. bo anti- ttom of tip b oard 73–3 (18 /8” 6.4 cm ) (213 29” 80 84–1 (204 –1/2” .6 to bocm) max . ttom a / .5 cm16” anti) ma t ope ip board x. ning heig & ht (73.7 c m) 2” 1–1/ m) (3.8 c nti-ti p bo of ard 23” (58.4 c m) Water Line Entry Area 3–1/ (8. 2” Note: Cutout opening shown with All Freezer model on left. Reverse water line entry if All Freezer model is on right. 7 (167 66” .6 cm ) –5/ (19.4 8” 6–3 / cm) 5/8 (17.1 4” cm) (1.5 c” m) 3” (7.6 cm) 3 (9.2 –5/8” cm 1 (27. 0–3/4 3 cm ” ) 66 One 2”x 4” mounting board per unit 1–1/2” (3.8 cm) x 3–1/2” (8.9 cm) 5/8” Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards by the difference. m) 1 – (26.0 7 c1m/2” ) p waO tertiona line l flo ent or ry 44 ) (167. ” 6 cm ) (1.5 c ) 9 cm (1.55/8” c m) 1” (2.5 cm) Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board. Note: Dimensions shown for 36” AF/AR model on the left. Reverse mounting boards if units are installed on the right. 45 Cutout Dimensions Anti-Tip Dimensions Dual 36” Designer Dual 36” Designer See An ti-Tip b oard in stallatio n 24” ) .0 cm (61 Electric Outlet Location 6” (15.2 c m) 9” (22.9 cm Anti-Tip Location 9” (22.9 ) c m) 79 (201 –3/8” .6 to bo cm) min . 82 (210 –7/8” .5 anti- cm) mi tip n. open board & ing h eigh t anti- ttom of tip b oard 73–3 (18 /8” 6.4 cm ) (213 29” 80 (73.7 c m) (204 –1/2” .6 to bo cm) max . ttom a 84–1 / .5 cm16” anti) ma t ope ip board x. ning heig & ht 2” 1–1/ m) ( 3. 8 c nti-ti o p bo f ard Water Line Entry Area 3–1/ (8. 2” Note: Cutout opening shown with All Freezer model on left. Reverse water line entry if All Freezer model is on right. 7 –5/ (19.4 8” 6–3 / cm) 5/8 (17.1 4” cm) (1.5 c” m) 3” (7.6 cm) (182 72” .9 cm ) ) 1 (27. 0–3/4 3 cm ” ) ) 72 (182. ” 9 cm ) One 2”x 4” mounting board per unit 1–1/2” (3.8 cm) x 3–1/2” (8.9 cm) 5/8 Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards by the difference. 1 – (26.0 7 c1m/2” ) p waO tertiona line l flo ent or ry 46 9 cm (1.5 c” m) 3 (9.2 –5/8” cm 29” (73.7 c m) (1.55/8” c m) 1” (2.5 c Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board. m) 47 Cabinet Information Cabinet Information (Designer) Designer models fit flush in standard 24” (61.0 cm) deep cabinet openings with no protrusion into the room except 2-1/2” (6.3 cm) handle depth. (Designer) Designer models fit flush in standard 24” (61.0 cm) deep cabinet openings with no protrusion into the room except 2-1/2” (6.3 cm) handle depth. Top View Overlapping cabinet doors Top View Wall Wall 3/4” (1.9 cm) space if 24” (63.5 cm) standard cabinet depth is used 1” (2.5 cm) space if 25” (63.5 cm) cabinet depth is used 25” (63.5 cm) Countertop depth 3/4” (1.9 cm) Full end panel 24-3/4” (62.9 cm) 3/4” 24” (1.9 cm) Full end panel (61.0 cm) Standard cabinet depth 24” (61.0 cm) Standard cabinet depth Cabinet door Door Door Flush Flush Top View Top View Flush mount cabinet doors Wall Wall 1” (2.5 cm) space if 25” (63.5 cm) cabinet depth is used 25” (63.5 cm) 1” (2.5 cm) space if 25” (63.5 cm) cabinet depth is used 3/4” 3/4” (1.9 cm) Full end panel 25” (63.5 cm) cabinet depth (1.9 cm) Full end panel Cabinet door Door Door Flush Flush 48 49 Custom Side Panel Dimensions (Professional) 3/16” 1 -7/ ) 227.0 cm (Designer & Professional Integrated) 3/4” (0.5 cm) Back filler panel 6” Custom Side Panel Dimensions (1.9 cm) End panel Z-Bracket 1/4” (0.6 cm) 4” -3/ ) 21.2 cm 6” m) .2 (15 1” (2.5 cm) c (55 (5 3/4” 5/32” (1.9 cm) End panel (0.4 cm) 4” -3/ ) 21.2 cm ” /16) 7 m 22 0 c (57 (55 . (2182-7 0.5 /8 cm ” to ) min 8 (21 4-1 . 3.5 /1 cm 6” )m ax .* (2182-7 0.5 /8 cm ” to ) min 8 (21 4-1 . 3.5 /1 cm 6” )m ax .* 6” m) .2 (15 (2182-7 0.5 /8 cm ” to ) min 8 (21 4-1 . 3.5 /1 cm 6” )m ax .* (2182-7 0.5 /8 cm ” to ) min 8 (21 4-1 . 3.5 /1 cm 6” )m ax .* c 4” 2 cm) .0 1 (6 4” -1/ ) 22 cm .5 (56 Optional kickplate notch Dimensions determined by cabinets 4” -1/cm) 2 2 (56 Optional kickplate notch ” 24 cm) Dimensions determined by cabinets .0 (61 .5 * Depending on how high leveling feet are raised, and cabinet enclosure height. * Depending on how high leveling feet are raised, and cabinet enclosure height. 50 51 General Information General Information Area Requirements Water Supply Requirements Verify the following: • Unit can fit into residence and can be moved around corners and through doorways. fused, electrical supply is required. It is required that a separate circuit serving only this appliance be provided. This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong, groundingtype wall receptacle. Do not use an extension cord. • Floors can support unit’s weight plus food weight (approximately 1200 pounds [540 kg] per unit). • Rear wall is solid and is able to support two horizontally mounted 2 X 4s (included) bolted to two wall studs. The 2 X 4 board bolt heads must be flush with 2 X 4 to prevent obstruction. If codes permit a separate grounding wire to be used, it is recommended that a qualified electrician determine that the grounding path is adequate. • Remove anything attached to rear or side walls that can obstruct unit installation. DO NOT ground to a gas pipe. Check with a qualified electrician if you are not sure the appliance is properly grounded. DO NOT have a fuse in the neutral or grounding circuit. • Cutout dimensions are accurate. • Electrical outlet is in correct location. • Water line is in correct location. Anti-Tip Requirements • Do not install a refrigeration unit near a heat source, nor in a location where the surrounding temperature will fall below 60º F (16º C). The anti-tip boards should be fastened into position prior to moving the unit into the opening. Note: Additional mounting boards may be required if the unit does not touch the back wall of the enclosure. To prevent unit from tipping forward, it must be secured in place with a solid soffit or wood block. Electrical Requirements It is the customer’s responsibility to: • contact a qualified electrical installer. • assure that the electrical installation is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70latest edition or Canadian Electrical Code C22.1-1998 and C22.2 No. 0-M91 (or latest edition), and all local codes and ordinances. A 115 volt, 60-Hz, 15 amp, • Do not use plastic water lines from the household plumbing to the water inlet valve connection on the refrigeration unit. WARNING To avoid serious illness or death, do not use unit where water is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. The contaminants or other substances removed or reduced by this water treatment system are not necessarily in you water. • Do not use the self-piercing feature of a saddle valve. The hole made by the piercing lance is too small for the water flow rate required by the ice maker. Use only 1/4” (6 mm) copper tubing for water line. Do Not install copper tubing in area where temperatures drop below 35° F (1.7° C). Before attaching copper tubing to the unit, flush at least 2 quarts (1.9 L) of water through the copper tubing and into a bucket to remove any particles in the water line. • If saddle valve is not used, place a separate shut-off valve in an easily accessible location between water supply and the unit. Do not locate shut-off valve behind the unit. • The installation of Viking units with a reverse osmosis system is acceptable as long as the water pressure remains within the allowable PSI as stated below. It is important to note that with many reverse osmosis systems, the pressure starts off high, but then it decreases as the water level of the reverse osmosis storage area drops. This must be considered when checking the water pressure coming into the unit. • Viking Range Corporation is not responsible for property damage due to improper installation or water connection. • Connect 1/4” (6 mm) flexible copper tubing to household plumbing in compliance with local codes and ordinances. • Connect a vertical or horizontal 1/2” (1.2 cm) to 1-1/4” (3.2 cm) COLD water line near water area. • Length of copper tubing must reach from water supply connection to the unit connection with an additional length to facilitate moving the unit out of enclosure for cleaning or service. Tubing should be soft instead of rigid and ends should be free of burrs. • Run water line through the floor, back, or side wall. Tubing should lay flat on floor underneath the unit. Clamp tubing to wall or floor. • Copper tubing route must be above 35° F (1.7° C) to prevent water line from freezing. 52 • Water pressure must be greater than 20 psi and less than 120 psi on non-dispensers and greater than 35 psi and less than 120 psi on dispensers. 53 Installation General Information • Most of the unit’s weight is at the top. Extra care is needed when moving the unit to prevent tipping. 1 2a TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions. Use two or more people to move and install appliance. Failure to do so can result in death or serious injury. • Do Not remove protective film until unit is in operating position. • All four leveling legs must contact the floor to support and stabilize the full weight. • Do not drop unit. Place unit in front of cutout. Unpacking unit • Remove exterior shipping materials prior to moving unit into home. (Professional) Lift center grille louver up and pull out. 1. Remove top and bottom strap. 3. Cut carton rear approximately 1/4” (0.6 cm) to 1” (2.5 cm) from right corner with a utility knife extended 1/4” (0.6 cm). • To avoid personal injury, wear gloves when performing any installation procedure and wear eye protection when cutting metal straps. 4. Remove carton and exterior packaging. Save cardboard shipping material to protect floor surface when installing unit. Remove anti-tip board, kickplate and door trim pieces (DF models) from rear of unit. Moving Unit 2b 3 designer 2. Remove top cap. • Use two or more people to move and install unit. Failure to follow this instruction can result in back or other injury. (Designer) Pull the center grille louver up at an angle and pull out. Using an 8” magnetic nut driver, remove the two 1/4” screws. 4 Remove shipping brackets from skid by removing 4 bolts (2 on each side) with a 1/2” deep-well socket wench and a pair of pliers. Note: Tilting unit is not required to remove shipping brackets. Slip appliance dolly between unit and skid. Only use dolly from the rear of the unit to remove unit from skid. After the unit is removed from the skid, a dolly can be used from either side or the back BUT NOT THE FRONT. Note: Use excess packaging to protect decorative trim; also, verify that leveling legs are up (0” adjustment). 54 Remove grille assembly. 55 Hinge Adjustment 6 5 Front of unit 9 10a 2 2 3” 1 1 Remove 4 side screws and remove unit top. 3 Plug in power cord to verify operation. Note: Make sure power switch and showroom switch are in the “On” Position. Loosen the 4 hinge screws. Adjust door. Retighten 4 hinge screws. Place unit within 3” of being flush with cabinets. Note: To avoid cabinet damage, place cardboard between cabinets and unit. When moving unit, do not crimp, kink or crush water supply line. 10b 7 11 1 2 Carefully move unit until semi flush with cabinet (depending on unit). Replace unit top. Replace 4 side screws. 8b 8a 13 12 Wall Wall 2x4 2x4 Refrigerator Pull supply tubing forward under unit. Note: DO NOT use plastic water lines. Refrigerator Attach a single 2 x 4 to wall stud (refer to dimensions page for exact location). If needed, depending on cabinet and depth, attach second 2 x 4 to first 2 x 4. 56 Flush water line by running two quarts of water into a bucket. Turn water off. Connect supply tube to water valve using a 1/2” wrench. Note: DO NOT overtighten. 57 Door Stop Adjustment 20 15 14 21 1 1 90˚ 110˚ 120˚ 3 2 2 Turn on water supply and check for leaks. Lift unit off rollers to desired height and level unit using a 5/16” head wrench. Note: DO NOT use an electric device. Overtightening can cause damage. Open refrigerator door so door stop and shoulder screw are accessible. Note: Shoulder screw should be in 110˚ door opening position. Remove shoulder screw and place in 90˚ or 120˚ position. Final Installation 17 16 Screw 23 22 Wall 2x4 Refrigerator Attach positive secure self-tapping bolts to 2 x 4 using a 22” extension. Verify that drain pan is installed and aligned. Replace top air grille. Using an 8”magnetic nut driver, replace the two 1/4” screws. Kickplate Installation 18 24a 19 1 24b designer 2 3 2 Using a Phillips screwdriver, attach the kickplate to the unit and adjust to desired height. Align holes on both ends of louvered panels and insert screws. 58 (Professional) Replace the center grille louver. (Designer) Replace the center grille louver. 59 25 26 Open door. Display should flash. Performance Checklist Press “ACTIVATE CONTROLS” button pad and close door. Note: There is a 6 minute delay before the unit starts. h Verify cabinet size. h Align/square door(s). h Verify electrical supply and water supply (if applicable). h Verify drain pan is properly installed and there are no leaks in water connection. h Install anti-tip device(s) and verify unit is secure. h Install kickplate. h Remove internal packaging and labels and wipe unit down. h Position unit in cutout, level at desired height, and secure unit. Installer’s information: h Plug-in unit and verify operation. h Connect water supply (if applicable). • Verify icemaker fill tube is properly inserted. • Verify icemaker bailarm is down. • Verify dispenser operation (if applicable). 60 Installer’s name:_____________________________ Installer’s company:_________________________ Date: ________________________________________ 61 Verify Operations Service & Registration Control Panels Only authorized replacement parts may be used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician. All Refrigerator All Freezer 1. Press “Activate Controls” pad. 2. Verify unit is not in Sabbath Mode. If in Sabbath Mode: A. The Sabbath Mode will disable the interior lights, display (except three blue squares) and alarm. (See picture below for visual indication of Sabbath Mode.) Record the following information indicated below. You will need it if service is ever required. The serial number and model number for your appliance are located on the identification plate mounted behind the top light. Model number _________________________________________ Serial number _________________________________________ To exit the Sabbath Mode: B. Press and hold “Activate Controls” and then “Display Off” for 3 seconds. (The control will beep three times to alert the user the Sabbath Mode has been exited.) 3. Verify unit is not in Showroom Mode. If in Showroom Mode: A. The Showroom Mode will disable the refrigerator system but all other functions are normal. These include lights and control. (See picture below for visual indication of Showroom Mode.) Date of purchase _________________________________________ Date installed _________________________________________ Dealer's name _________________________________________ Address To exit Showroom Mode: B. Press and hold “Activate Controls”; while holding, press and hold “Higher” and “Alarm Off” together. (The control will beep three times to alert the user that Showroom Mode has been exited.) 4. Press “Alarm Off” and “Display Off” at the same time and hold until beeps (force start compressor). 5. All models need to be set at the fifth bar for Refrigerator and Freezer - factory setting. 62 _________________________________________ 63