Download PAMX2 Owner Manual-ok
Transcript
PROFESSIONAL SPEAKERS, AMPLIFIERS AND ACCESSORIES Audiodesign Srl Via dell’industria, 28 - 42025 CAVRIAGO (RE) +39 0522 941444 - Fax +39 0522 942363 www.audiodesign-pro.com [email protected] OWNER MANUAL PAMX2.62 - PAMX2.102 PROFESSIONAL MIXERS Serie PAMX2 PAMX2. 102 2 R 20 2 5 2 0 5 L 13/14 SOLO CLIP MUTE 11/12 SOLO CLIP dB 10 SOLO CLIP MUTE SOLO SOLO ALT 3-4 ALT 3-4 MUTE dB 2 MUTE 1 MUTE PRE 2 2 AUX Copy this page to fix the set up dB 1 MIC 1 1 1 2 CLIP CLIP MUTE PAN PAN dB ALT 3-4 3 FX FX 2 PRE 80 Hz 80 Hz 1 LOW LOW AUX MID 2.5 kHz 12 kHz 12 kHz MID EQ HIGH EQ MIC 2 HIGH MUTE 3 SOLO CLIP MUTE dB 4 PAN FX 2 PRE 1 AUX 80 Hz LOW MID 2.5 kHz 12 kHz EQ MIC 3 HIGH ALT 3-4 MUTE 4 SOLO CLIP MUTE dB 5 ALT 3-4 PAN FX 2 PRE 1 AUX 80 Hz LOW MID 2.5 kHz 12 kHz EQ MIC 4 HIGH MUTE 5 SOLO CLIP MUTE dB 6 ALT 3-4 PAN FX 2 PRE 1 AUX 80 Hz LOW MID 2.5 kHz 12 kHz EQ MIC 5 HIGH MUTE 6 SOLO CLIP MUTE dB 7 ALT 3-4 PAN FX 2 PRE 1 AUX 80 Hz LOW MID 2.5 kHz 12 kHz EQ MIC 6 HIGH MUTE 7 SOLO CLIP MUTE dB 8 PAN FX 2 PRE 1 AUX 80 Hz LOW MID 2.5 kHz 12 kHz EQ MIC 7 HIGH ALT 3-4 MUTE 8 SOLO CLIP MUTE dB 9 ALT 3-4 PAN FX 2 PRE 1 AUX 80 Hz LOW MID 2.5 kHz 12 kHz EQ MIC 8 HIGH MUTE 9 SOLO CLIP MUTE dB ALT 3-4 10 MUTE PAN FX dB MUTE ALT 3-4 ALT 3-4 PAN MUTE 11/12 BAL FX FX MUTE 13/14 BAL FX PRE 2 PRE 2 PRE 2 PRE 1 AUX 80 Hz LOW MID 2.5 kHz 12 kHz EQ MIC 9 HIGH ALT 3-4 MODE SOLO (NORMAL) PFL (LEVEL SET) 4 3 SOURCE MAIN MIX MAIN SOLO PFL PHONES/CTRL R ALT 3-4 2-TR/USB SOLO MAX 2-TR/USB TO MAIN FX 2 SOLO FX 2 AUX AUX AUX 80 Hz LOW MID 2.5 kHz 12 kHz EQ MIC 10 HIGH 1 80 Hz LOW MID 2.5 kHz 12 kHz EQ HIGH 1 80 Hz LOW 1 AUX SENDS MID 2.5 kHz 12 kHz EQ HIGH LINE IN 7/8 LINE IN 5/6 RIGHT 10 MAIN MIX ALT 3-4 1 SEND 1 1 mA LAM P 12V 400 TO AUX STEREO AUX RETURNS PROGRAM ( PUSH ) CE INTERFA USB CHORUS & REVERB FLANGER & REVERB PHASER & REVERB PITCH & REVERB DELAY & REVERB DELAY & GATED DELAY & REVERSE DELAY & CHORUS DELAY & FLANGER DELAY & PHASER DELAY & PITCH 80 82 84 86 88 90 91 92 94 96 98 REVERSE EARLY REFL AMBIENCE STADIUM AMBIENCE FX DELAY ECHO CHORUS FLANGER PHASER PITCH SHIFT 36 40 44 48 49 50 59 60 66 70 74 24-BIT MULTI-FX PROCESSOR 00 03 06 09 10 13 16 19 20 27 30 AUX SENDS 2 2 FX Conformity: Audiodesign Pro products comply with presently existing directives and standards. LEFT/ MONO Precautions: Caution: When using any electric product , precautions should always be taken, including the following: 1) Read carefully all instructions before using the product. 2) To reduce the risk, strict supervision is necessary when the product is used near children. 3) Don't use the product near to water sources like sinks, kitchens, wet floors, pools, or similar or when raining. 4) In case hearing losses or buzzing occur, please contact a doctor. 5) This products should be located so that its position does not interfere or reduce its proper ventilation. 6) This product should be site away from heat sources such as radiators or any other product that generate heat. 7) This product should be connected to a power supply line only of the type described on the operating instructions. Check always the status of the power cable. 8) In case you need to replace the fuse, unplug power supply before replacement. The fuse is located over the power outlet and needs to be replaced with a fuse of same type and value. If the fuse blows again, please contact our service. DON'T replace it a second time with a higher value fuse. 9) Unplug power supply when left unused for a long period of time. Don't draw the cable but pull out the plug. 10) Make sure that power switch can always be easily reached. 11) Make sure that objects or liquids don't fall inside the product. 12) The product needs to be inspected by authorized or qualified personnel in case: A- The power cable or plug are damaged B- Objects or liquids fall inside the product C- The product has been exposed to rain D- The product doesn't appear to operate normally or exhibits a marked change in performance. E- The product has fallen and been damaged. 13) DON'T operate on the product, except indications on the user's manual . Please refer to authorized and qualified personnel for any other operation. 14) Caution: Don't place objects on the product's power cable or place it in a position where it could be damaged or cause interferences. Improper installation could cause fire risk and/or personal injury. SMALL HALL MID HALL BIG HALL CHURCH SMALL ROOM MID ROOM BIG ROOM CHAPEL SPRING SPRING GATED REV X 2 .10 2 PAM INPUT OUTPUT CD/TAPE 1 Rear panel .. .............................. Pag 7 Connections........................................ Pag 7 DSP effects ........................................ Pag 7 USB connection.... ............................. Pag 8 Technical specifications....................... Pag 8 Block diagram .. .. ............................... Pag 9 Set Up Memo PAMX2.62.... ................ Pag 10 Set Up Memo PAMX2.102.... .............. Pag 11 1 Contents Introduction ..................................... Pag 2 Precautions......................................... Pag 2 Conformity .......................................... Pag 2 Service …….................................. Pag 3 Quick start .......................................... Pag 3 Mono channel ..................................... Pag 4 Stereo channel.................................... Pag 5 Master section .................................... Pag 6 ULTRALOW-NOISE DESIGN 14-INPUT 2/2-BUS MIC/LINE MIXER WITH PREMIUM MIC PREAMPLIFIERS AND DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR USB AUDIO INTERFACE A low noise and distortion-less circuitry assures a natural and transparent reproduction. USB interface for computer connection. MAIN MIX SET UP MEMO Introduction Congratulations on the purchase of a professional mixing console PAMX2. The mic pre-amplifiers are of high quality level and ensure the best sound quality and a very high dynamic. 2.5 kHz MIXER PROFESSIONALI PAMX2. 62 MIXER PROFESSIONALI SET UP MEMO LEFT/ MONO Service All Audio Design PRO products have been inspected and tested before leaving the factory and , if properly used, they will work for many years. However, in case of any problem, please proceed in the following way: RIGHT 1 MIC 2 MIC 3 MIC 4 MIC 5 INPUT OUTPUT CD/TAPE 1 2 MIC 1 Serie PAMX2 PAM 2 FX X 2 .6 2 ULTRALOW-NOISE DESIGN 14-INPUT 2/2-BUS MIC/LINE MIXER WITH PREMIUM MIC PREAMPLIFIERS AND DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR USB AUDIO INTERFACE MIC 6 AUX SENDS Contact your dealer and inform about the defect you found In case it won't be possible to solve the problem with the dealer, the product needs to be returned, preferably in its original packaging or in a proper packing to protect it during the transport. Purchase documents must be produced too. Your dealer will arrange the shipment to our service centre. 24-BIT MULTI-FX PROCESSOR 00 03 06 09 10 13 16 19 20 27 30 SMALL HALL MID HALL BIG HALL CHURCH SMALL ROOM MID ROOM BIG ROOM CHAPEL SPRING SPRING GATED REV 36 40 44 48 49 50 59 60 66 70 74 REVERSE EARLY REFL AMBIENCE STADIUM AMBIENCE FX DELAY ECHO CHORUS FLANGER PHASER PITCH SHIFT 80 82 84 86 88 90 91 92 94 96 98 CHORUS & REVERB FLANGER & REVERB PHASER & REVERB PITCH & REVERB DELAY & REVERB DELAY & GATED DELAY & REVERSE DELAY & CHORUS DELAY & FLANGER DELAY & PHASER DELAY & PITCH USB INTERFA LAM P LINE IN 7/8 LINE IN 5/6 EQ EQ EQ EQ EQ EQ EQ EQ HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz MID MID MID MID MID MID MID MID 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 12V 400 1 LOW LOW LOW LOW LOW LOW LOW 80 Hz 80 Hz 80 Hz 80 Hz 80 Hz 80 Hz 80 Hz 80 Hz mA PROGRAM ( PUSH ) AUX SENDS LOW CE STEREO AUX RETURNS 1 1 TO AUX SEND 1 SOLO 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 2 2 FX FX MAIN MIX ALT 3-4 SOLO 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE Set the levels: 1. Push the button "MODE" to use LED level indicators , in PFL mode (Level Set) 2. Push the button "SOLO " of the channel you intend to set up. 3. Set the TRIM potentiometer of the channel until the LED indicators (left column) are next to "0" level or in any case never over +5 level. Avoid absolutely to reach level + 10/Clip. 4. Release button "SOLO" of the channel you have just set up. 5. Repeat procedure from point 2 to point 4 for each channel you intend to connect 2-TR/USB TO MAIN 2-TR/USB FX FX FX FX FX FX FX 10 FX 5 ALT 3-4 2 MAX PHONES/CTRL R PAN PAN PAN PAN PAN PAN BAL 0 BAL 2 MAIN MIX SOURCE 1 2 3 MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 MUTE dB 1 MUTE dB 5 4 MUTE dB MUTE dB 6 MUTE dB 7/8 MUTE dB dB MUTE dB CLIP CLIP CLIP CLIP CLIP CLIP SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO 4 5 6 7/8 4 MUTE CLIP 3 5 20 CLIP 2 MAIN SOLO PFL 9/10 3 9/10 QUICK START: Start up: 1. Turn the power switch OFF. 2. Set "down" all TRIM controls (all counter clockwise ) and FADER ( all down) . 3. Center EQ controls (High - Mid - Low) and PAN controls (12 hours). 4. Set all push buttons in their "off" position (button up). 5. Set "down" all master section controls (counter clockwise and down) Connections: If you already know how you want to connect the mixer, go ahead and connect. If you prefer to inspect operation, please follow these instructions: 1. Plug a microphone or a mono signal source into one of the mono channels. 2. or a stereo signal source into one the stereo channels. 3. Connect MAIN OUTPUTS to an amplifier (XLR Balanced / Jack Balanced). 4. Turn power switch on. The blue led (POWER) lights up. MODE SOLO (NORMAL) PFL (LEVEL SET) L R Mixing: 1. Set the FADER of each channel at "0" position 2. Release the button "MODE" to set it in position "SOLO" (NORMAL) 3. Turn the button "MAIN MIX" to see outlet signal level on the LED indicators. 4. Turn up "MAIN MIX" to desired level, in relation to the amplifiers / speakers you are using. Preferably, don't exceed level "0" or "+5" on the LED indicators. 5. Adjust FADER of each channel to obtain your own mix. 6. If necessary, adjust tones and repeat above " set levels" procedures ALT 3-4 MAIN MIX General indications: 1. The optimum FADER position is near to 0 while the optimum position for the MAIN MIX is the one that don't exceed level 0 / +5 on the LED level indicators. 2. Check that the level of each power input is the same that you set up during the "set the levels" operations, even if you have eventually operated on EQ of each channel. If necessary, each channel can be adjusted even during the performance through TRIM set up and monitored throught the LED indicators. Avoid absolutely that CLIP indicator of each channel lights up. 3. In case you intend to connect further sources, please take care to turn down "MAIN MIX" slider Copy this page to fix the set up 3 MIXER PROFESSIONALI Serie PAMX2 MIXER PROFESSIONALI SCHEMA A BLOCCHI MONO CHANNELS Mic 1 Bal or Unbal LINE IN Low Cut 75 Hz 18 dB/Oct +10 +10 - 40 +60 TRIM dB/dBu EQ 0 HIGH 12 KHz - 15 +15 0 MID 2.5 KHz - 15 +15 0 LOW 80 Hz - 15 +15 AUX 0 -¥ + 15 0 PRE FX -¥ + 15 Left Right PAN 1 MUTE ALT 3-4 MUTE 10 CLIP 0 SOLO 10 15 20 30 40 60 Fig 1 1. MIC: XLR balanced microphone input for dynamic and capacitor microphones. By means of the XLR connector, it's possible to feed condenser microphones. Operate button "PHANTOM ON" to activate this function ( located on the rear panel) This function is monitored through the red LED switch on + 48 V located over the LED level indicators. Use of dynamic microphones with phantom power supply is generally not recommended. * 2. LINE: balanced or unbalanced line level input , 6,3 mm. Jack connector. Important: DON'T use MIC and LINE input signal at the same time !!!! * 3. This switch activates high-pass filter at 75 Hz - 18dB/Oct 4. TRIM: To adjust channel input level. Should always be completely turned counter clockwise during connection of any source 5. EQ HIGH: This control adjusts +/- 15 dB with a "shelving" curve shape at 12 kHz. 6. EQ MID: This control adjusts +/- 15 dB with a band center at 2.5 kHz. 7. EQ LOW: This control adjusts +/- 15 dB with a "shelving" curve shape at 80 Hz. 8. AUX: This control adjusts the output signal level AUX SENDS 1, controlled through general adjustment (18). This signal is normally "post" FADER but could become "pre" FADER by operating the button (9) 9. This button operates the pre/post FADER level of the AUX control 10. FX: This control adjusts signal level to send to AUX SENDS 2 and to DSP, controlled through general adjustment (19). This signal is always "post" FADER 11. PAN: It adjusts the stereo scene by adjusting the signal levels to send to right and left outputs. 12. MUTE: This dual-purpose switch turns off the channel and sends at the same time a signal to an alternative mixing (ALT 3/4 ). Function is on when yellow LED lights up. 13. CLIP: The red LED is dual-purpose too: it indicates "SOLO" function (See point 14) or indicates CLIPPING mode. Important: in case LED lights up indicating clipping mode, operate by reducing the TRIM 14. SOLO: This button sends the signal to PHONES and CONTROL ROOM OUT outlets and allows you to hear signals through your headphones and view signal on LED level indicators. Operating the "MODE" switch of the main section, it's possible to choose pre or post FADER signal. 15. FADER: It adjusts the level of the channel signal. * See connection scheme on page 7 4 9 Serie PAMX2 Serie PAMX2 MIXER PROFESSIONALI PORTA USB Audiodesign PRO professional mixers PAMX2 series, are supplied with a full speed USB port which you can connect to a computer and allows you to exchange CD-quality audio between mixer and computer; mixer operates also as and external soundcard. Recording on PC can be made using the computer's built-in audio recorder, or better, using a dedicated software. Windows automatically recognizes the mixer at the first connection and proceed to install necessary drivers, eventually will require to insert the Windows CD. Open the control panel and select "USB Audio Codec" as default sound recording and playback device. Also for Macintosh, the selection of "USB Audio Codec" is the only action required. Better performances can be obtained using specific Digital Audio Workstation software, in which case the specific installation instruction must be followed. To use the mixer for playback from PC, operate buttons and controls 2 TR/USB, for MAIN MIX or PHONES/CTRL R outputs. For recording to PC from Mixer while it's working, start registration on PC's software and adjust its level from the MAIN MIX Fader. Serie PAMX2 SPECIFICATIONS STEREO CANNELS Section Connector Level and datas MONO INPUT CHANNELS Sensitivity from Mic In 0 to - 60 dB XLR-F Balanced Impedance 2 Kohm Sensitivity from MONO - 10 a + 4 dB Jack Balanced Impedance 10-20 Kohm (Bal-Unbal) Jack Unbalanced Line In L 16 Bal or Unbal HIGH ±15 dB @ 12 KHz shelving EQ MID ±15 dB @ 2.5 KHz peaking 17 R LOW ±15 dB @ 80 Hz shelving LEVEL +4 -10 STEREO INPUT CHANNELS Sensitivity from To ensure that the mixer is correctly recognized by the PC, always turn on the mixer before inserting USB cable into the PC. When turning off, turn off the computer first until shut down process is completed and then turn off the mixer. MIXER PROFESSIONALI Line In Impedance 20 - 10 a + 4 dB Jack Balanced Jack Unbalanced Kohm LINE IN 9/10 EQ 0 HIGH ±15 dB @ 12 KHz shelving MID EQ HIGH ±15 dB @ 2.5 KHz peaking 12 KHz - 15 +15 LOW ±15 dB @ 80 Hz shelving 0 MASTER SECTION MID 2.5 KHz MAIN MIX OUT Nominal Output level + 4 dBu XLR / Jack Bal. C. ROOM output Nominal Output level + 4 dBu Jack Unbal mono AUX SENDS 1 Nominal Output level + 4 dBu Jack Unbal mono AUX SENDS 2 Nominal Output level + 4 dBu - 15 +15 0 LOW 80 Hz - 15 +15 Jack Unbal mono AUX 0 2-TRK - CD/TAPE Nominal Output level 0 dBu RCA Nominal Output level - 10 dBv -¥ HEADPHONES Min Impedance Max Output 32 ohm (2x) 193 mW Jack Stereo PRE FX DIGITAL EFFECT PROCESSOR -¥ Reverbs: HALL, ROOM, VOCAL e PLATE Delay STEREO, MONO e TAP Modulations CHORUS e FLANGER Combinations REV + STEREO DELAY, REV + MONO DELAY, REV +CHORUS e REV + FLANGER Preset + 15 PAN Left Right 9/10 MUTE USB INTERFACE ALT 3-4 Version Fully compliant with USB 1.1 Resolution 16-Bit Delta Sigma ADC e DAC Sampling Rate DAC: 32, 44.1, 48 kHz ADC: 8, 11.025, 16, 22.05, 32, 44.1, 48 kHz CLIP 0 SOLO 10 Max Level all outputs Crosstalk meas at 1 KHz > 82 dB Hum and Noise unweighted < -93 dBu 40 THD + Noise a +4dB, 1kHz < 0,008 % 60 Weight Dimensions (WxDxH) MUTE 10 MAIN SPECIFICATIONS 8 + 15 0 +22 dBu 15 20 30 PAMX 2.62 PAMX 2.102 4.0 Kg 5.3 Kg 34.4 x 35 x 11.2 cm 45 x 35 x 11.2 cm 16. L channel of a stereo source or a mono signal can be connected to this 6,3 mm Jack input. Signal can be either balanced or unbalanced* 17. Only R channel of a stereo signal can be connected to this 6.3 mm input 3. This switch sets the channel input level (+ 4 / - 10 dB attenuation) 5. EQ HIGH: This control adjusts +/- 15 dB with a "shelving" curve shape at 12 kHz. 6. EQ MID: This control adjusts +/- 15 dB with a band center at 2.5 kHz. 7. EQ LOW: This control adjusts +/- 15 dB with a "shelving" curve shape at 80 Hz. 8. AUX:This control adjusts the output signal level AUX SENDS 1, controlled through general adjustment (18). This signal is normally "post" FADER but could become "pre" FADER by operating the button (9) 9. This button operates the pre/post FADER level of the AUX control 10. FX: This control adjusts signal level to send to AUX SENDS 2 and to DSP, controlled through general adjustment (19).This signal is always "post" FADER 11. PAN: It adjusts the stereo scene by adjusting the signal levels to send to right and left outputs. 12. MUTE: This dual-purpose switch turns off the channel and sends at the same time a signal to an alternative mixing (ALT 3/4 ). Function is on when yellow LED lights up. 13. CLIP: The red LED is dual-purpose too: it indicates "SOLO" function (See point 14) or indicates CLIPPING mode. Important: in case LED lights up indicating clipping mode, operate by reducing the TRIM 14. SOLO: This button sends the signal to PHONES and CONTROL ROOM OUT outlets and allows you to hear signals through your headphones and view signal on LED level indicators. Operating the "MODE" switch of the main section, it's possible to choose pre or post FADER signal. 15. FADER: It adjusts the level of the channel signal. Fig 2 * See connection scheme on page 7 5 Serie PAMX2 MIXER PROFESSIONALI MASTER SECTION AUX SENDS 18. It controls the signal general level to send to AUX SENDS 1. Push button SOLO to view level on LED indicators. 19. It controls the signal general level to send to AUX SENDS 2 and to DSP; Level is shown on DPS LED indicators. Push button SOLO to view level on LED indicators too. 20. This unbalanced Jack sends the signal of all input channels AUX (8) controls together with STEREO AUX RETURNS 1 (25) signal. 21. This unbalanced Jack sends the signal of all input channels FX (10) controls REAR PANEL 25 20 30 Serie PAMX2 MIXER PROFESSIONALI 46 50 16 31 MAIN OUTPUT LEFT / MONO 1 RIGHT INPUT 1 OUTPUT CD/TAPE R USB CHANNEL INSERT 6 L 5 4 3 2 1 INTERFACE FX 2 STEREO AUX RETURNS 26 L L R R MAIN OUTPUT POWER PHANTOM ON ON 2 I 0 AUX SEND 21 STEREO AUX RETURNS 22. It controls the signal level arriving from STEREO AUX RETURNS 1 (25) towards the MAIN MIX 23. It controls the signal level arriving from STEREO AUX RETURNS 1 (25) towards AUX SEND 1 (20). 24. It controls the signal level sent to STEREO AUX RETURNS 2 (26) It also determine the action level of the internal DSP. The button located next to it allows you to send the signal to MAIN MIR or to ALT 3-4. 25. Unbalanced Jack connectors of the auxiliary stereo input. In case of mono signal, use left connector 26. Unbalanced Jack connector of the auxiliary stereo input. In case of mono signal, use left connector HEADPHONES 27. Switch to select the source to send to the headphones output and to view signal level on the LED indicators 28. Controls general signal level to send to headphones Jack and CONTROL ROOM OUT output 29. Jack stereo to connect headphones CD/TAPE - 2TR/USB 30. Auxiliary input RCA connectors 31. Auxiliary output RCA connectors (MAIN MIX) 32. Button to send input signal to CD/TAPE and/or 2TR/USB to MAIN MIX, and vice versa to send output signal from MAIN MIX to CD/TAPE and/or 2TR/USB. DSP 33. DSP - Digital effect processor. Rotate this switch in both directions to preset effect you want to use. See details of effects on page 7Various 34. LED BLUE light Mixer is on 35. LED RED light, Phantom is connected 36. LED level indicators (red Clipping) 37. MODE: Button to select the signal (SOLO or PFL) to send to LED level indicator. 38. FX FOOTSW: allows you to use a footswitch to use or not to use preset effects 39. LAMP: bayonet connector to plug a lamp (12 v CC - 400 mA max) to MAIN - ALT FADER MAIN - ALT FADER 40. FADER to control left and right levels of the ALT 3-4 bus 41. FADER to control left and right level of the main MAIN MIX bus 6 FX FOOTSW 42 16 29 39 PHONES LAMP 12 V CC - 400 mQ 24-BIT DUAL ENGINE DSP CLIP -3 -8 -10 -15 -20 33 24-BIT A/D & D/A CONVERTER LEVEL AUX SENDS -PROGRAM (PUSH) STEREO AUX RETURNS 0 0 22 0 TO AUX 18 SOLO -¥ + 15 0 + 15 -¥ 0 FX 19 23 SEND 1 -¥ 24 32 -¥ + 15 4 3 CONTROL ROOM OUT R MAIN MIX ALT 3-4 + 15 2TR/USB 27 ALT 3-4 +48V CLIP 10 5 2 - ¥ + 15 PHONES/CTRL R 0 2 5 20 MAIN MIX MAIN SOLO SOURCE R L 44 43 16 16 45 - PIN 3 = COLD 47 48 16 49 16 51 16 42. Power supply and fuse connection 43. Mixer switch on button 44. Phantom + 48V power supply switch 45. USB connection 46. 6.3 mm Jack balanced connections for main output MAIN OUTPUTni 47. XLR balanced connections for main output MAIN OUTPUT 48. 6.3 mm Jack unbalanced connections for ALT 3-4 output 49. Control Room output or additional output of MAIN MIX program with 6.3 mm mono unbalanced Jack 50. Stereo Jack connections of each channel, to operate signal externally (equalization / compression/etc.) 51. MAIN MIX output stereo Jack connections to operation signal externally CONNECTIONS + 48 V 2TR/USB TO MAIN 0 P0WER 34 MAIN INSERT L FX SOLO -¥ + 15 L I 0 PIN 2 = HOT 38 ALT 3-4 OUTPUT R PFL - 35 28 36 Phantom Power Supply XLR 3 Male XLR 3 Female LEFT RIGHT 37 MODE 3 10 4 10 SOLO (NORMAL) PFL (LVEL SET) 10 L R 10 Jack 6,3 Balanced 0 0 0 0 10 10 10 10 15 15 15 15 20 20 20 20 30 30 30 30 40 40 40 40 60 60 60 60 ALT 3-4 40 MAIN MIX 41 Jack 6,3 Unbalanced DSP EFFECTS 00 SMALL HALL 03 MID HALL 06 BIG HALL 09 CHURCH 10 SMALL ROOM 13 MID ROOM 16 BIG ROOM 19 CHAPEL 20 SPRING 27 SPRING 30 GATER REV 36 REVERSE 40 EARLY REFL 44 AMBIENCE 48 STADIUM 49 AMBIENCE FX 50 DELAY Jack 6,3 Stereo INSERT CONNECTIONS 59 ECHO 60 CHORUS 66 FLANGER 70 PHASER 74 PITCH SHIFT 80 CHORSU & REVERB 82 FLANGER & REVERB 84 PHASER & REVERB 86 PITCH & REVERB 88 DELAY & REVERB 90 DELAY & GATED 91 DELAY & REVERSE 92 DELAY & CHORUS 94 DELAY & FLANGER 96 DELAY & PHASER 98 DELAY & PITCH OUT IN MIXER INSERT IN Compressor Processor Equalizer OUT Compressor Processor Equalizer 7