Download TRIO CLUB GB.cdr
Transcript
OTHER SYSTEMS OF THE TRIO FAMILY TRIO SESSION TRIO MASTER Subwoofer 12” - 320 mm - VC 65 mm Satellites 2 x 8” - 200 mm - VC 50 mm Horn Compression Tweeter - VC 34 mm Power Max/RMS: 1280 / 640 W SPL Max: 124 dB Subwoofer 15” - 380 mm - VC 75 mm Satellites 2 x 10” - 250 mm - VC 50 mm Horn Compression Tweeter - VC 44 mm Power Max/RMS: 1440 / 720 W SPL Max: 127 dB Full Range Sound System PROFESSIONAL SPEAKERS, AMPLIFIERS AND ACCESSORIES Audiodesign Srl Via dell’industria, 28 - 42025 CAVRIAGO (RE) +39 0522 941444 - Fax +39 0522 942363 www.audiodesign-pro.com [email protected] TRIO CLUB User Manual Portable Full Range Sound System TRIO CLUB Introduction Thank you for purchasing an AudioDesign TRIO Active Sound system. TRIO series is designed to provide an high and powerful sound quality in a compact size. The main features are: * Active subwoofer cabinet with additional amplifiers for the passive satellites. * High sensitivity passive satellites. * High and precise acoustic quality also with high power. * Portability: the system is easy fit and portable by one person. The final result is a full, detailed and powerful sound. Application The KPRO TRIO systems are a professional solution for every DJ or Live events where high pressure and extreme sound quality is required. Portable Full Range Sound System TRIO CLUB TECHNICAL SPECIFICATIONS INPUT SUBWOOFER STAGE PRO W10 LINE IN: Combo Socket XLR 3-F / Jack Stereo INPUT: Balanced and Unbalanced OUTPUT SATELLITES OUTPUT: Speakon NL4 (pin 1+ = +, pin 1- = -) AMPLIFIERS Subwoofer Power Output: Satellites Power Outputi: SPEAKER WEIGHT & SIZES Precautions: Caution: When using any electric product , precautions should always be taken, including the following: 1) Read carefully all instructions before using the product. 2) To reduce the risk, strict supervision is necessary when the product is used near children. 3) Don't use the product near to water sources like sinks, kitchens, wet floors, pools, or similar or when raining. 4) In case hearing losses or buzzing occur, please contact a doctor. 5) This products should be located so that its position does not interfere or reduce its proper ventilation. 6) This product should be site away from heat sources such as radiators or any other product that generate heat. 7) This product should be connected to a power supply line only of the type described on the operating instructions. Check always the status of the power cable. 8) In case you need to replace the fuse, unplug power supply before replacement. The fuse is located over the power socket and needs to be replaced with a fuse of same type and value. If the fuse blows again, please contact our service. DON'T replace it a second time with a higher value fuse. 9) Unplug power supply when left unused for a long period of time. Don't draw the cable but pull out the plug. 10) Make sure that power switch can always be easily reached. 11) The product needs to be inspected by authorized or qualified personnel in case: A- The power cable or plug are damaged B- Objects or liquids fall inside the product C- The product has been exposed to rain D- The product doesn't appear to operate normally or exhibits a marked change in performance. E- The product has fallen and been damaged. 12) DON'T operate on the product, except indications on the user's manual . Please refer to authorized and qualified personnel for any other operation. 13) Caution: Don't place objects on the product's power cable or place it in a position where it could be damaged or cause interferences. Improper installation could cause fire risk and/or personal injury. INPUT SPEAKERS MAIN FEATURES WEIGHT & SIZES 250 W RMS 2x125 W RMS @ 4 Ohm Load Electronic Crossover LP Subwoofer: 46 - 240 Hz / 12 dB/Oct. Frequency Electronic Crossover HP Satellites: Frequency 38 - 250 Hz / 12 dB/Oct. Subwoofer: 1 x 10” (250 mm) VC 50 mm Frequency Response: 30 ÷ 260 Hz (± 3 dB) SPL Max: Max: 121 123 dB SPL Weight Subwoofer: Sizes (WxLxH) cm: 32 kg 43 x 39 x 39 SATELLITE STAGE PRO 65 SATELLITES INPUT: Speakon NL4 (pin 1+ = +, pin 1- = -) (165 mm) 1 x 6.5” High Sensitivity Woofer VC 30 mm Dome Tweeter TOTAL IMPEDANCE : TOTAL POWER : TOTAL SPL Max: Frequency Response: Tweeter Crossover: Weight Satellite: Size (WxLxH) cm: VC 32 mm 4 Ohm 160 W RMS (250 W Max) with X-over 200 Hz 18 dB/oct 121 dB 100 ÷ 20000 Hz (± 3 dB) 12 dB/oct Passive 6000 Hz 4 kg 20 x 19 x 27 BY MEANS OF OUR ACCESSORIES, DIFFERENT CONFIGURATIONS OF THE SYSTEM ARE POSSIBLE Service All Audio Design PRO products have been inspected and tested before leaving the factory and , if properly used, they will work for many years. However, in case of any problem, please proceed in the following way: Contact your dealer and inform about the defect you found In case it won't be possible to solve the problem with the dealer, the product needs to be returned, preferably in its original packaging or in a proper packing to protect it during the transport. Purchase documents must be produced too. Your dealer will arrange the shipment to our service centre. Conformity: Audiodesign Pro products comply with presently existing directives and standards. -2- (500 W Max) (2x250 W Max) -7- Portable Full Range Sound System TRIO CLUB Portable Full Range Sound System TRIO CLUB 6 Volume setting of the system is made by means of the three LEVEL knobs on top of the subwoofer: 6 - Left satellite is GAIN LEFT 6 - Right satellite is GAIN RIGHT - Subwoofer is GAIN SUBWOOFER 3 6 3 SYSTEM COMPONENTS Thi TRIO CLUB stereo system is composed by three elements: PEAK L HI PASS GAIN HIGH LOW PASS 80 80 120 60 50 Hz 260 +15 0 10 50 Hz GAIN GAIN HIGH HI PASS 80 PHASE SHIFT 120 60 -15 PEAK PEAK 0 - 180° 260 0 10 0 10 -15 +15 R 50 Hz 260 POWER LEFT speaker Subwoofer 1 Active Subwoofer STAGE PRO W10 2 Passive Satellites STAGE PRO 65 120 60 Active Subwoofer STAGE PRO W10 R IGHT speaker Before switching power on and proceed to system setting, make sure that all three knobs are completely turned counterclockwise, at level 0, and that the mixer output is set so that the peaks level stays about within 0 e +3 dB. The active subwoofer STAGE PRO W10 is equipped with a 10" (250 mm) woofer with 50 mm VC. The cabinet integrates all necessary electronics for amplification and system processing: Set first the satellites volume alone and then the subwoofer volume alone. 3 amplifiersi in AB Class for a total power of 500 W RMS (1000 W Max) Satellites Volume setting 1 x 250 W RMS (500 W Max) for the Subwoofer itself 2 x 125 W RMS (250 W Max) for the two passive satellites (@ 4 Ohm load) Switch power on and begin to turn clockwise the satellite GAIN knobs 6 until the correspondent PEAK led begins to flash shortly for less than 1 second. This is the optimal level being connected to a mixer sending to MAIN a signal with level peaks within 0 and +3dB. The Subwoofer signal is LowPass filtered, adjustable from 46 to 240 Hz 12 dB/oct. The Satellites signals are HighPass filtered, adjustable from 38 to 250 Hz 12 dB/oct. Now listen to the satellites with this output level; if you detect distorsion or saturation of the signal (i.e of microphone) check the possibility of reducing the level of the signal concerned at his source, otherwise try to slightly lower the mixer’s main otput. Should this not be enough, reduce the satellites volume until you have an optimal sound. Memorize the knobs setting. Cabinet of high density MDF, anti-scratch embossed painting Practical transport handles hollowed into the wood Integral rigid metal grill Sub Volume setting After having memorized the knobs setting LEFT e RIGHT, take them back to 0 and begin now to turn clockwise the SUBWOOFER GAIN knob 3 until the correspondent PEAK led begins to flash shortly for less than 1 second. This is the optimal level being connected to a mixer sending to MAIN a signal with level peaks within 0 and +3dB. Housing hole for ø 35 mm stand tubes Sizes & weight: 43 x 39 x 39 cm; 32 kg. Now listen to the Sub with this output level; if you detect distorsion of basses, turn slightly the knob back counterclokwise. Connections and Control Panels Final system setting Bring the three knobs at the optimal level you have checked and listen to the complete system, again at the mixer main level peaks between 0 and +3 dB. If you detect to much basses compared with satellites output, turn slightly back the SUB LEVEL knob. If you detect instead not enough basses, turn slightly back the setellites LEVEL LEFT and RIGHT knobs. 2 Subwoofer LOW PASS control adjustable from 46 to 240 Hz 8 7 6 5 2 1 3 PEAK L As a general rule , the output level of the mixers should be set so that the sound peaks remain between 0 to +3 dB about. When the system TRIO CLUB gets in the two Line In (10 and 11) a signal with that amplitude and it is set as explained above, it grants the maximum performance in terms of maximum undistorted amplification (at clip limit) and in this conditions you get the maximum possible sound pressure (SPL). 1 Subwoofer Clip Indicator GAIN HIGH HI PASS 80 120 50 Hz 260 +15 0 10 50 Hz GAIN GAIN HIGH 80 0 - 180° 260 R HI PASS PHASE SHIFT 120 60 -15 3 Subwoofer Volume control PEAK PEAK LOW PASS 80 60 5 6 7 8 0 10 10 -15 +15 50 Hz 260 POWER LEFT speaker Subwoofer 4 Phase Switch 0-180° 120 60 0 5 Satellites Clip Indicator (Separated Left and Right) R IGHT speaker 4 9 6 Satellites Volume control separated on channel LEFT and RIGHT. it controls only the signal going respectively to left and right satellite. 7 High tones equalization separated for left and right channel -15 / +15 dB RESPONSE DIAGRAM TRIO CLUB Sensitivity Magnitude 13 12 11 18 10 8 Satellites HI PASS control separated LEFT and RIGHT from 38 to 250 Hz ATTENTION: the HI PASS frequency should not be set under 120 Hz - dB SPL/watt (4 ohm load) M L S S A 95.0 90.0 85.0 9 ON LED indicator (Red) LINE IN OUTPUT 10 Right Channel Line In OUT+:1+/ OUT- :1- Combo Socket XLR 3-F / Jack 6,3 mm Balanced ST MONO LEFT LEFT(Mono) RIGHT SPEAKER OUTPUT: RIGHT GND=1=SLEEVE HOT=2=TIP COLD=3=RING 11 Left Channel Lin In Combo Socket XLR 3-F / Jack 6,3 mm Balanced 80.0 13 Speakon Socket Left Satellite 220 70.0 65.0 60.0 USE ONLY WITH 250V FUSE 75.0 12 Speakon Socket Right Satellite 14 Amplifier cooling fan; keep it clean for a correct ventilation. 15 On/Off power switch - In positioe 0 the system is Off 55.0 16 Voltage Selector 50.0 17 Power Net Socket 45.0 18 ST/MONO Switch (Stereo / Mono): se si seleziona STEREO, aut o 20.0 100.0 1000.0 10000.0 log Frequency - Hz MLSSA: Frequency Domain AUDIODESIGN PRO: TRIO CLUB -6- When STEREO is selected, the system sends to the Right and Left channels the correspondent Right and Left input signals. When MONO is selected, the system sends to both Right and Left channels only the LEFT input signal, so one complete system per channel can be used.. -3- Portable Full Range Sound System TRIO CLUB Portable Full Range Sound System TRIO CLUB High sensitivity passive satellites STAGE PRO 65 CONNECTION OF TWO SYSTEMS IN MONO CONFIGURATION The high sensitivity passive satellite STAGE PRO 65 is a bass reflex cabinet equipped with: One 6.5" (165 mm) woofer with a 32 mm vented voice coil (ST/MONO Switch down) RIGHT CHANNEL LEFT CHANNEL One DOME tweeter with a 30 mm voice coil LEFT/ MONO RIGHT 1 MIC 2 MIC 3 MIC 4 MIC 5 INPUT OUTPUT CD/TAPE 1 2 MIC 1 PAM 2 FX X 2 .6 2 ULTRALOW-NOISE DESIGN 14-INPUT 2/2-BUS MIC/LINE MIXER WITH PREMIUM MIC PREAMPLIFIERS AND DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR USB AUDIO INTERFACE MIC 6 AUX SENDS High Pass Filter at 6000 Hz 12 dB/oct on tweeter 24-BIT MULTI-FX PROCESSOR 80 CHORUS & REVERB 82 FLANGER & REVERB 84 PHASER & REVERB 86 PITCH & REVERB 88 DELAY & REVERB 90 DELAY & GATED 91 DELAY & REVERSE 92 DELAY & CHORUS 94 DELAY & FLANGER 96 DELAY & PHASER 98 DELAY & PITCH 36 REVERSE 40 EARLY REFL 44 AMBIENCE 48 STADIUM 49 AMBIENCE FX 50 DELAY 59 ECHO 60 CHORUS 66 FLANGER 70 PHASER 74 PITCH SHIFT 00 SMALL HALL 03 MID HALL 06 BIG HALL 09 CHURCH 10 SMALL ROOM 13 MID ROOM 16 BIG ROOM 19 CHAPEL 20 SPRING 27 SPRING 30 GATED REV USB INTERFA LINE IN 5/6 4 ohm Impedance LAM LINE IN 7/8 EQ EQ EQ EQ EQ EQ EQ EQ HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz MID MID 2.5 kHz MID 2.5 kHz MID 2.5 kHz MID 2.5 kHz MID 2.5 kHz MID 2.5 kHz P 12V 400 PROGRAM ( PUSH ) MID 2.5 kHz 2.5 kHz AUX SENDS Speakon socket for connection to the subwoofer amplifier 1 LOW LOW 80 Hz LOW 80 Hz LOW 80 Hz LOW 80 Hz LOW 80 Hz LOW 80 Hz CE mA STEREO AUX RETURNS 1 1 TO AUX LOW 80 Hz 80 Hz SEND 1 SOLO 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 2 FX FX MAIN MIX ALT 3-4 SOLO 2-TR/USB TO MAIN 2-TR/USB Cabinet in high density MDF , embossed anti-scratch painting FX FX FX FX FX FX FX FX PAN PAN PAN PAN PAN PAN BAL BAL 10 5 ALT 3-4 2 MAX PHONES/CTRL R 0 2 MAIN MIX MAIN SOLO PFL 5 SOURCE 1 2 3 5 6 MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 dB MUTE Integral protection grill dB MUTE 4 dB MUTE dB MUTE dB MUTE 7/8 dB MUTE dB 9/10 MUTE dB 20 3 4 MUTE CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO MODE SOLO (NORMAL) PFL (LEVEL SET) L R Housing hole for ø 35 mm stand tubes 1 2 3 4 5 6 7/8 9/10 AL T 3-4 MAIN MIX Sizes and Weight: 20 x 19 x 27 cm; 5 kg. LINE IN OUTPUT OUT+:1+/ OUT- :1- LINE IN OUTPUT OUT+:1+/ OUT- :1- ST MONO ST MONO LEFT LEFT(Mono) RIGHT SPEAKER OUTPUT: LEFT LEFT(Mono) RIGHT SPEAKER OUTPUT: GND=1=SLEEVE HOT=2=TIP COLD=3=RING SYSTEM CONNECTION IN STEREO CONFIGURATION (ST/MONO Swich up) 220 RIGHT 1 MIC 3 MIC 4 MIC 5 INPUT OUTPUT CD/TAPE 1 2 MIC 2 PAM 2 FX USE ONLY WITH 250V FUSE 220 NET USE ONLY WITH 250V FUSE LEFT/ MONO MIC 1 RIGHT GND=1=SLEEVE HOT=2=TIP COLD=3=RING RIGHT X 2 .6 2 ULTRALOW-NOISE DESIGN 14-INPUT 2/2-BUS MIC/LINE MIXER WITH PREMIUM MIC PREAMPLIFIERS AND DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR USB AUDIO INTERFACE MIC 6 AUX SENDS 24-BIT MULTI-FX PROCESSOR 80 CHORUS & REVERB 82 FLANGER & REVERB 84 PHASER & REVERB 86 PITCH & REVERB 88 DELAY & REVERB 90 DELAY & GATED 91 DELAY & REVERSE 92 DELAY & CHORUS 94 DELAY & FLANGER 96 DELAY & PHASER 98 DELAY & PITCH 36 REVERSE 40 EARLY REFL 44 AMBIENCE 48 STADIUM 49 AMBIENCE FX 50 DELAY 59 ECHO 60 CHORUS 66 FLANGER 70 PHASER 74 PITCH SHIFT 00 SMALL HALL 03 MID HALL 06 BIG HALL 09 CHURCH 10 SMALL ROOM 13 MID ROOM 16 BIG ROOM 19 CHAPEL 20 SPRING 27 SPRING 30 GATED REV USB INTERFA LINE IN 5/6 LEFT CHANNEL LAM LINE IN 7/8 EQ EQ EQ EQ EQ EQ EQ EQ HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz P 12V 400 RIGHT CHANNEL PROGRAM ( PUSH ) MID MID MID MID MID MID MID MID 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz AUX SENDS STEREO AUX RETURNS 1 LOW LOW 80 Hz LOW 80 Hz LOW 80 Hz LOW 80 Hz LOW 80 Hz LOW 80 Hz 1 1 TO AUX LOW 80 Hz CE mA 80 Hz SEND 1 SOLO 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 1 AUX 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 PRE 2 2 FX FX MAIN MIX ALT 3-4 SOLO 2-TR/USB TO MAIN 2-TR/USB FX FX FX FX FX FX FX FX PAN PAN PAN PAN PAN PAN BAL BAL 10 5 ALT 3-4 2 MAX PHONES/CTRL R 0 2 MAIN MIX MAIN SOLO PFL 5 SOURCE 1 2 MUTE 3 MUTE ALT 3-4 MUTE MUTE ALT 3-4 dB MUTE 5 4 MUTE ALT 3-4 dB MUTE 6 MUTE ALT 3-4 dB MUTE 7/8 MUTE ALT 3-4 dB MUTE 9/10 MUTE ALT 3-4 dB MUTE dB ALT 3-4 MUTE Depending on the choosen configuration, connect the system following the precedent wiring schemes. 20 MUTE ALT 3-4 dB 3 dB 4 MUTE CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO MODE SOLO (NORMAL) PFL (LEVEL SET) L R Connection to the electric net 2 3 4 5 7/8 6 9/10 AL T 3-4 Check that Power switch 15 is in position 0 and that net voltage corresponds to the one selected in the system. Connect the supplied electric wire to an electric net socket equipped with a correct ground contact. MAIN MIX . . Satellite connection Use wires with good quality Speakon plugs. Make sure to rotate the Speakon plugs clockwise up to the lock position. Connection to the mixer LINE IN OUTPUT OUT+:1+/ OUT- :1- ST MONO LEFT LEFT(Mono) RIGHT SPEAKER OUTPUT: Before making any connection to the mixer make sure the system power switch is Off in order to avoid damages. Remember that electric net power il the last to be switced On and the first to be disconnected after use! RIGHT GND=1=SLEEVE HOT=2=TIP COLD=3=RING System Volume setting USE ONLY WITH 250V FUSE 220 1 NET The TRIO CLUB system is provided vith clip limiters and peack level indicators separate and independent on all three channels, and doesn’t require therefore any special setting procedure. Thus the system is able to deliver excellent performances, and should be used with input signals at optimal level, starting from kind and quality of the used cables, and the prevention of any kind of distortion. In fact the presence of distortion doesn’t only deliver a poor performance of the system, but it is also a real risk on long periods, to damage the system itself. We kindly invite you therefore,to strictly follow the following instructions on how to set the level of alla components. -4-5-