Download ER-OLED0 .84-1 - Display Future

EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
ER-OLED0 .84-1
OLED Module User Manual
EastRising Technology Co., Limited
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
i
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
Contents
1. Basic Specifications .................................................................................. 1~4
1.1
1.2
1.3
1.4
1.5
1.6
Display Specifications .................................................................................................1
Mechanical Specifications ...........................................................................................1
Active Area & Pixel Construction ...............................................................................1
Mechanical Drawing....................................................................................................2
Pin Definition...............................................................................................................3
Block Diagram .............................................................................................................4
2. Absolute Maximum Ratings .......................................................................... 5
3. Optics & Electrical Characteristics ........................................................... 6~7
3.1 Optics Characteristics ..................................................................................................6
3.2 DC Characteristics ................................................... . ................................................6
3.3 AC Characteristics ...... .............. ..... ....... .... .... .. . ...... ...... ......... ....... .. ...... ...7
4. Functional Specification ....... ................................................................... 8~9
4 1 Commands .. ..... ...... .... ............... ...... ...... . ......... ....... ......... ...... ..... ....... .... .8
4.2 Power down and Power up Sequence ...... ...................................................................8
4.2.1 Power up Sequence ........... . ..... ......................................................................8
4.2.2 Power down Sequence ... ...... ............................................................................8
4.3 Reset Circuit........................ ..... ..................................................................................8
4.4 Actual Application Example ........................................................................................9
5. Reliability ................. .................................................................................... 10
5.1 Contents of Reliability Tests......................................................................................10
5.2 Lifetime......................................................................................................................10
5.3 Failure Check Standard..............................................................................................10
6. Outgoing Quality Control Specifications .............................................. 11~15
6.1 Environment Required ...............................................................................................11
6.2 Sampling Plan ............................................................................................................11
6.3 Criteria & Acceptable Quality Level .........................................................................11
6.3.1 Cosmetic Check (Display Off) in Non-Active Area ........................................11
6.3.2 Cosmetic Check (Display Off) in Active Area.................................................14
6.3.3 Pattern Check (Display On) in Active Area.....................................................15
7. Package Specifications ................................................................................ 16
8. Precautions When Using These OEL Display Modules ....................... 17~19
8.1
8.2
8.3
8.4
Handling Precautions .................................................................................................17
Storage Precautions....................................................................................................18
Designing Precautions ...............................................................................................18
Precautions when disposing of the OEL display modules.........................................19
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
ii
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
8.5 Other Precautions.......................................................................................................19
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
iii
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
1. Basic Specifications
1.1 Display Specifications
1)
2)
3)
Display Mode:
Display Color:
Drive Duty:
Passive Matrix
Monochrome (Light Blue)
1/16 Duty
1.2 Mechanical Specifications
1)
2)
3)
4)
5)
6)
7)
Outline Drawing:
Number of Pixels:
Panel Size:
Active Area:
Pixel Pitch:
Pixel Size:
Weight:
According to the annexed outline drawing
96 × 16
29.10 × 9.20 × 1.60 (mm)
21.104 × 3.504 (mm)
0.22 × 0.22 (mm)
0.204 × 0.204 (mm)
0.89 (g)
1.3 Active Area & Pixel Construction
0.22x96-0 01 =21.104 (A/A)
P0.22x16-0.016=3.504 (A/A)
Display Pattern
Segment 127
( Column 1 )
Segment 32
( Column 96 )
Common 0
( Row 16 )
Common 15
( Row 1 )
0.22
0.204
0.22
0.204
Display Pattern
Scale (10:1)
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:1
(2 1)
(1 1)
0 5±0 5
URL: www.lcd-china.com
3.50 (A/A)
Document Name: ER-OLED0.84-1 Manual
(1 6)
(1 76)
Customer Approval
Signature
5 504 (V/A)
1 6±0 1
9 2±0 2 (Cap Size)
8 2 (Polarizer)
9 2±0 2 (Panel Size)
Unless Otherwise
0 1±0 03
mm
ecif
T lerance
Dimension
±0 3
Angle
±1
General Roughness
Unit
0 22
0 204
Detail "A"
Scale (10:1)
( Column 96 )
( Column 1 )
By
Date
Ti
Drawn
Humphrey Lin
20080715
EE
James Wang
20080715
Panel / E
Ivy Lo
20080715
ER-OLED0.84-1
PM
Cherry Lin
20080715
( Row 1 )
Common 15
( Row 16 )
Common 0
Segment 32
Segment 127
"A"
P0 22x96-0 016=21 104 (A/A)
Date
20080715
EASTRISING TECHNOLOGY CO.,LTD
P0 22x16-0 016=3 504 (A/A)
Color: Light Blue
Driver IC: SSD1306
FPC Number: ER-OLED0 84-1
Interface: I2C
General Tolerance: ±0 30
The total thickness (1 70 Max) is without polarizer protective film & remove tape
The actual assembled total thickness with above materials should be 1 95 Max
(Reference Mechnical Design)
(30 7)
6 2±0 3
Contact Side
(0 75)
Glue
Contact Sid
P0.62 14-1) 8.06±0 05
Remove Tape
t=0 15mm Max
R
2-R0 4±0 1
R
2±0 3
01
W=0 32±0.03
(21 98)
8±0 3
3M #1318B
8 4x8x0 063mm
1
14
1
±0
0 47±0 1
Polarizer
t=0 2mm
Active Area 0 84
96 x 16 Pixels
5±0 3
10 5±0 3
6 799
61
4
(0 1)
0 204
0 22
1
2
3
4
5
6
Notes:
0 3±0 3
(1 1)
(2 1)
(39 6)
29 1±0 2 (Panel Size)
25 5±0 2 (Cap Size)
24 5 (Polarizer)
23 104 (V/A)
21 104 (A/A)
10±0 3
Item
A
Remark
Material
Drawing Number
Symbol
C2P
C2N
C1P
C1N
VBAT
VBREF
VSS
VDD
RES#
SCL
SDA
IREF
VCOMH
VCC
Rev
A
Scale
1:1
Sheet
1 of 1
Size
A3
Soda Lime / Polyimide
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Original Drawing
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
1.4 Mechanical Drawing
Page:2
The drawing contained herein is the exclusive property of EastRising
It is not allowed to copy, reproduce and or disclose in a ny formats without permission of EastRising
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
1.5 Pin Definition
Pin Number
Symbol
Type
VDD
P
Function
Power Supply
Powerr Supplyy for Lo
ogic
8
This is a voltage supply pin. It must be connected to
external source.
Ground of OEL System
7
VSS
P
This is a ground pin. It also acts as a reference for the
logic pins, the OEL driving voltages, and the analog
circuits. It must be connected to external ground.
Power Supply for OEL Panel
14
VCC
P
This is the most positive voltage supply pin of the chip.
A stabilization capacitor should be connected between
this pin and VSS when the converter is used. It must be
connected to external source when the converter is not
used.
Drivver
Current Reference for Brightness Adjustment
12
IREF
I
This pin is segment current reference pin. A resistor
should be connected between this pin and VSS. Set the
current lower than 12.5μA.
Volta
age Ou
utput High Leveel fo
or COM Signal
13
VCOMH
O
This pin is the input pin for the voltage output high level
for COM signals. A capacitor should be connected
between this pin and VSS.
DC/DC Conveerter
Power Supply for DC/DC Converter Circuit
5
VBAT
P
This is the power supply pin for the internal buffer of the
DC/DC voltage converter. It must be connected to
external source when the converter is used. It should be
connected to VDD when the converter is not used.
Volta
age Reffereence for DC/D
DC Conveerter Circu
uit
6
3/4
1/2
VBREF
P
C1P / C1N
C2P / C2N
I
RES#
I
This pin is the internal voltage reference of booster
circuit. A stabilization capacitor should be connected
between this pin and VSS.
Positive Terminal of the Flying Inverting Capacitor
Negative Terminal of the Flying Boost Capacitor
The charge-pump capacitors are required between the
terminals. They must be floated when the converter is
not used.
Interface
Powerr Reeset fo
or Contrrolleer and Driiveer
9
This pin is reset signal input. When the pin is low,
initialization of the chip is executed.
I2C Bus Cllockk Signal
10
SCL
I
11
SDA
I/O
The transmission if information in the I2C bus is
following a clock signal. Each transmission of data bit
is taken place during a single clock period of this pin.
I2C Bus Da
ata Signal
URL: www.lcd-china.com
This pin acts as a communication channel between the
transmitter and the receiver.
Document Name: ER-OLED0.84-1 Manual
Page:3
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
1.6 Block Diagram
~
Common 15
~ ~ ~
Common 0
Segment 32
Segment 127
Active Area 0.84"
96 x 16 Pixels
C7
C6
IREF
VCOMH
VCC
SCL
SDA
VDD
RES#
VSS
C2P
C2N
C1P
C1N
VBAT
VBREF
SSD1306
R2
R3
C2
C1
R1
C4
C5
C3
Pins connected to MCU interface: RES#, SCL, and SDA
C1, C3, C6, C7:
C3, C4:
C5:
R1:
R2, R3:
URL: www.lcd-china.com
1μF
2.2μF
22nF
820kΩ, R1 = (Voltage at IREF – VSS) / IREF
2kΩ
Document Name: ER-OLED0.84-1 Manual
Page:4
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
2. Absolute Maximum Ratings
Parameter
Symbol
Min
Max
Unit
Notes
Supply Voltage for Logic
VDD
-0.3
4
V
1, 2
Supply Voltage for Display
VCC
0
15
V
1, 2
Operating Temperature
TOP
-30
70
°C
-
Storage Temperature
TSTG
-40
80
°C
-
Note 1: All the above voltages are on the basis of “GND = 0V”.
Note 2: When this module is used beyond the above absolute maximum ratings,
permanent breakage of the module may occur. Also, for normal operations, it is
desirable to use this module under the conditions according to Section 3.
“Optics & Electrical Characteristics”. If this module is used beyond these
conditions, malfunctioning of the module can occur and the reliability of the
module may deteriorate.
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:5
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
3. Electrical Characteristics
3.1 Optics Characteristics
Characteristics
Symbol
Conditions
Brightness
Lbr
(x)
(y)
CR
With Polarizer
C.I.E. (Blue)
Dark Room Contrast
Min
Typ
Max Unit
100 120
cd/m2
0.12 0.16 0.20
0.22 0.26 0.30
- >2000:1 -
Without Polarizer
View Angle
>160
-
-
degree
* Optical measurement taken at VDD = 2.8V, VCC = 7.25V.
Software configuration follows Section 4.4 Initialization.
3.2 DC Characteristics
Characteristics
Symbol
Conditions
Min
Typ Max Unit
Supply Voltage for Logic
VDD
-
1.65
2.8
3.3
V
Supply Voltage for DC/DC
VBAT
-
4.2
V
Supply Voltage for Display
VCC
Note 3
7
7.25
75
V
High Level Input
VIH
-
-
VDD
V
Low Level Input
VIL
-
0.8×VDD
0
-
V
High Level Output
VOH
-
Low Level Output
VOL
IOUT = 100μA, 3.3MHz 0.9×VDD
IOUT = 100μA, 3.3MHz 0
0.2×VDD
VDD
Operating Current for VDD
IDD
Operating Current for VBAT
IBAT
Int rnal DC/DC Enable 3 3
V
-
Note 4
-
Note 5
-
0.1×VDD V
180 300 μA
180 300 μA
Note 4
-
7.5
9.4
mA
Note 5
-
12.6
15.8
mA
Sleep Mode Current for VDD IDD, SLEEP
-
-
1
5
μA
Sleep Mode Current for VCC ICC, SLEEP
-
-
1
5
μA
Note 3: Brightness (Lbr) and Supply Voltage for Display (VCC) are subject to the
change of the panel characteristics and the customer’s request.
Note 4: VDD = 2.8V, VCC = 7.25V, 50% Display Area Turn on.
Note 5: VDD = 2.8V, VCC = 7.25V, 100% Display Area Turn on.
* Software configuration follows Section 4.4 Initialization.
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:6
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
3.3 AC Characteristics
Symbol
tcycle
tHSTART
tHD
Description
Min
Max
Unit
Clock Cycle Time
2.5
-
us
Start Condition Hold Time
0.6
-
us
-
ns
Data Hold Time (for “SDAOUT” Pin)
0
Data Hold Time (for “SDAIN” Pin)
300
100
-
ns
0.6
-
us
tSSTOP
Data Setup Time
Start Condition Setup Time
(Only relevant for a repeated Start
condition)
Stop Condition Setup Time
0.6
-
us
tR
Rise Time for Data and Clock Pin
300
ns
300
ns
-
us
tSD
tSSTART
tF
Fall Time for Data and Clock Pin
Idle Time before a New Transmission can
tIDLE
Start
* (VDD - VSS = 2.8V, Ta = 25°C)
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
1.3
Page:7
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
4. Functional Specification
4.1. Commands
Refer to the Technical Manual for the SSD1306
4.2 Power down and Power up Sequence
To protect OEL panel and extend the panel life time, the driver IC power up/down
routine should include a delay period between high voltage and low voltage power
sources during turn on/off. It gives the OEL panel enough time to complete the
action of charge and discharge before/after the operation.
4.2.1 Power up Sequence:
1.
2.
3.
4.
5.
6.
Power up VDD
Send Display off command
Initialization
Clear Screen
Power up VCC
Delay 100ms
(When VCC is stable)
7. Send Display on command
VDD on
VCCC on
n
Displayy on
n
VCC
VDD
VSS/G ound
4.2.2 Power down Sequence:
1. Send Display off command
2. Power down VCC
3. Delay 100ms
(When VCC is reach 0 and panel
is completely discharges)
4. Power down VDD
Displlayy off
VCC off
VDD offf
VCC
VDD
VSS/Ground
4.3 Reset Circuit
When RES# input is low, the chip is initialized with the following status:
1. Display is OFF
2. 128×64 Display Mode
3. Normal segment and display data column and row address mapping (SEG0
mapped to column address 00h and COM0 mapped to row address 00h)
4. Shift register data clear in serial interface
5. Display start line is set at display RAM address 0
6. Column address counter is set at 0
7. Normal scan direction of the COM outputs
8. Contrast control register is set at 7Fh
9. Normal display mode (Equivalent to A4h command)
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:8
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
4.4 Actual Application Example
Command usage and explanation of an actual example
<Initialization>
Set Display Off
0xAE
Set Low Power Display Mode
0xD8, 0x05
Set VCOMH Deselect Level
0xDB, 0x20
Set Display Clock Divide Ratio/Oscillator Frequency
0xD5, 0x80
Set Segment Re-Map
0xA1
Set Entire Display On/Off
0xA4
Set Multiplex Ratio
0xA8, 0x0F
Set COM Output Scan Direction
0xC8
Set Normal/Inverse Display
0xA6
Set Display Offset
0xD3, 0x00
Se COM Pins H rdware Co figuration
0xDA, 0x02
Clear Screen
Set Display Start Line
0x40
Set Contrast Control
0x81, 0xAF
Set Display On
0xAF
Set Charge Pump
0x8D, 0x14
Set Pre-Charge Period
0xD9, 0xF1
If the noise is accidentally occurred at the displaying window during the operation,
please reset the display in order to recover the display function.
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:9
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
5. Reliability
5.1 Contents of Reliability Tests
Item
Criteria
Conditions
High Temperature Operation
70°C, 240 hrs
Low Temperature Operation
-30°C, 240 hrs
High Temperature Storage
80°C, 240 hrs
Low Temperature Storage
-40°C, 240 hrs
The operational
functions work.
High Temperature/Humidity Operation 60°C, 90% RH, 120 hrs
-40°C ⇔ 85°C, 24 cycles
Thermal Shock
60 mins dwell
* The samples used for the above tests do not include polarizer.
* No moisture condensation is observed during tests.
5.2 Lifetime
End of lifetime is specified as 50% of initial brightness reached.
Parameter
Min
Operating Life Time 10 000
Storage Life Time
20,000
Max
Unit
Condition
2
Notes
-
hr
120 cd/m , 50% Checkerboard
6
-
hr
Ta = 25°C, 50% RH
-
Note 6: The average operating lifetime at room temperature is estimated by the
accelerated operation at high temperature conditions.
5.3 Failure Check Standard
After the completion of the described reliability test, the samples were left at room
temperature for 2 hrs prior to conducting the failure test at 23±5°C; 55±15% RH.
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:10
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
6. Outgoing Quality Control Specifications
6.1 Environment Required
Customer’s test & measurement are required to be conducted
conditions:
Temperature:
Humidity:
Fluorescent Lamp:
Distance between the Panel & Lamp:
Distance between the Panel & Eyes of the Inspector:
Finger glove (or finger cover) must be worn by the inspector.
Inspection table or jig must be anti-electrostatic.
under the following
23 ± 5°C
55 ± 15 %RH
30W
≥ 50 cm
≥ 30 cm
6.2 Sampling Plan
Level II, Normal Inspection, Single Sampling, MIL-STD-105E
6.3 Criteria & Acceptable Quality Level
Partition
AQL
Definition
Major
0.65
Defects in Pattern Check (Display On)
Minor
1.0
Defects in Cosmetic Check (Display Off)
6.3.1 Cosmetic Check (Display Off) in Non-Active Area
Check Item
Classification
Criteria
X > 6 mm (Along with Edge)
Y > 1 mm (Perpendicular to edge)
X
Panel
General Chipping
Y
Minor
X
Y
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:11
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
6.3.1 Cosmetic Check (Display Off) in Non-Active Area (Continued)
Check Item
Classification
Criteria
Any crack is not allowable.
Panel Crack
Minor
Cupper Exposed
(Even Pin or Film)
Minor
Film or Trace Damage
Minor
Not Allowable by Naked Eye
Inspection
Not Allowable
Terminal Lead Twist
Minor
Not Allowable
Terminal Lead Broken
Minor
Terminal Lead Prober
Mark
Acceptable
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:12
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
6.3.1 Cosmetic Check (Display Off) in Non-Active Area (Continued)
Classification
Check Item
Criteria
NG if any bent lead cause lead
shorting.
Minor
Terminal Lead Bent
(Not Twist or Broken)
NG for horizontally bent lead more
than 50% of its width.
Minor
Glue or Contamination
on Pin
(Couldn’t Be Removed
by Alcohol)
Minor
Ink Marking on Back
Side of panel
(Exclude on Film)
Acceptable
URL: www.lcd-china.com
Ignore for Any
Document Name: ER-OLED0.84-1 Manual
Page:13
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
6.3.2 Cosmetic Check (Display Off) in Active Area
Check Item
Classification
Any Dirt & Scratch on
Acceptable
Polarizer’s Protective Film
Scratches, Fiber, Line-Shape
Defect
Minor
(On Polarizer)
Dirt, Black Spot, Foreign
Material,
Minor
(On Polarizer)
Dent, Bubbles, White spot
(Any Transparent Spot on
Polarizer)
Criteria
Ignore for not Affect the
Polarizer
W ≤ 0.1
Ignore
W > 0.1, L ≤ 2
n≤1
L>2
n=0
Φ ≤ 0.1
Ignore
0.1 <Φ ≤ 0.25
n≤1
0.25 <Φ
n=0
Φ ≤ 0.5
Î Ignore if no Influence on
Display
0.5 < Φ
n=0
Minor
Fingerprint, Flow Mark
Minor
Not Allowable
(On Polarizer)
* Protective film should not be tear off when cosmetic check.
** Definition of W & L & Φ (Unit: mm):
Φ = (a + b) / 2
L
b: Minor Axis
W
a: Major Axis
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:14
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
6.3.3 Pattern Check (Display On) in Active Area
Check Item
Classification
No Display
Major
Flicker
Major
Missing Line
Major
Pixel Short
Major
Darker Pixel
Major
Wrong Display
Major
Un-uniform
Major
URL: www.lcd-china.com
Criteria
Not Allowable
Document Name: ER-OLED0.84-1 Manual
Page:15
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
7. Package Specifications
EPE COVER FOAM 351x212x1,
ANTISTATIC x 1 Pcs
x 1 pcs (Empty)
B Pcs Tray Vacuum packing
Module
EPE PROTECTTIVE
x A pcs
Staggered Stacking
Tray 420x285 T=0.8mm
Primary Box C SET
Wrapped with adhesive tape
x B pcs
Vacuum packing bag
EPE PROTECTTIVE
370mm x 280mm x 20mm
CARTO BOX
Label
Pr mary L450mm x W296 x H110, B wave
x CPcs
Part ID :
Label
Lot ID :
Q'ty :
QC :
Carton Box L464mm x W313mm x H472mm, AB wave
(Major / Maximum)
Item
Quantity
Holding Trays
(A)
15
per Primary Box
Total Trays
(B)
16
per Primary Box (Including 1 Empty Tray)
Primary Box
(C)
1~4
per Carton (4 as Major / Maximum)
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:16
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
8. Precautions When Using These OEL Display Modules
8.1 Handling Precautions
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Since the display panel is being made of glass, do not apply mechanical
impacts such us dropping from a high position.
If the display panel is broken by some accident and the internal organic
substance leaks out, be careful not to inhale nor lick the organic substance.
If pressure is applied to the display surface or its neighborhood of the OEL
display module, the cell structure may be damaged and be careful not to apply
pressure to these sections.
The polarizer covering the surface of the OEL display module is soft and easily
scratched. Please be careful when handling the OEL display module.
When the surface of the polarizer of the OEL display module has soil, clean the
surface. It takes advantage of by using following adhesion tape.
* Scotch Mending Tape No. 810 or an equivalent
Never try to breathe upon the soiled surface nor wipe the surface using cloth
containing solvent such as ethyl alcohol, since the surface of the polarizer will
become cloudy.
Also, pay attention that the following liquid and solvent may spoil the
polarizer:
* Water
* Ketone
* Aromatic Solvents
Hold OEL display module very carefully when placing OEL display module
into the system housing. Do not apply excessive stress or pressure to OEL
display module. And, do not over bend the film with electrode pattern layouts.
These stresses will influence the display performance. Also, secure sufficient
rigidity for the outer cases.
Do not apply stress to the LSI chips and the surrounding molded sections.
Do not disassemble nor modify the OEL display module.
Do not apply input signals while the logic power is off.
Pay sufficient attention to the working environments when handing OEL
display modules to prevent occurrence of element breakage accidents by static
electricity.
* Be sure to make human body grounding when handling OEL display
modules.
* Be sure to ground tools to use or assembly such as soldering irons.
* To suppress generation of static electricity, avoid carrying out assembly work
under dry environments.
* Protective film is being applied to the surface of the display panel of the OEL
display module. Be careful since static electricity may be generated when
exfoliating the protective film.
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:17
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
11) Protection film is being applied to the surface of the display panel and removes
the protection film before assembling it. At this time, if the OEL display
module has been stored for a long period of time, residue adhesive material of
the protection film may remain on the surface of the display panel after
removed of the film. In such case, remove the residue material by the method
introduced in the above Section 5).
12) If electric current is applied when the OEL display module is being dewed or
when it is placed under high humidity environments, the electrodes may be
corroded and be careful to avoid the above.
8.2 Storage Precautions
1)
2)
When storing OEL display modules, put them in static electricity preventive
bags avoiding exposure to direct sun light nor to lights of fluorescent lamps, etc.
and, also, avoiding high temperature and high humidity environments or low
temperature (less than 0°C) environments. (We recommend you to store these
modules in the packaged state when they were shipped from EastRising
Technology Ltd.)
At that time, be careful not to let water drops adhere to the packages or bags nor
let dewing occur with them
If electric current s applied wh n water drops ar adhering to the surface of the
OEL display module when the OEL display module is being dewed or when it
is placed under high humidity environments, the electrodes may be corroded
and be careful about the above.
8.3 Designing Precautions
1)
2)
3)
4)
5)
6)
7)
8)
The absolute maximum ratings are the ratings which cannot be exceeded for
OEL display module, and if these values are exceeded, panel damage may be
happen.
To prevent occurrence of malfunctioning by noise, pay attention to satisfy the
VIL and VIH specifications and, at the same time, to make the signal line cable
as short as possible.
We recommend you to install excess current preventive unit (fuses, etc.) to the
power circuit (VDD). (Recommend value: 0.5A)
Pay sufficient attention to avoid occurrence of mutual noise interference with
the neighboring devices.
As for EMI, take necessary measures on the equipment side basically.
When fastening the OEL display module, fasten the external plastic housing
section.
If power supply to the OEL display module is forcibly shut down by such errors
as taking out the main battery while the OEL display panel is in operation, we
cannot guarantee the quality of this OEL display module.
The electric potential to be connected to the rear face of the IC chip should be
as follows: SSD1306
* Connection (contact) to any other potential than the above may lead to
rupture of the IC.
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:18
EASTRISING TECHNOLOGY CO.,LIMITED
旭 日 东 方 科 技 有 限 公 司
8.4 Precautions when disposing of the OEL display modules
1)
Request the qualified companies to handle industrial wastes when disposing of
the OEL display modules. Or, when burning them, be sure to observe the
environmental and hygienic laws and regulations.
8.5 Other Precautions
1)
2)
3)
4)
5)
When an OEL display module is operated for a long of time with fixed pattern
may remain as an after image or slight contrast deviation may occur.
Nonetheless, if the operation is interrupted and left unused for a while, normal
state can be restored. Also, there will be no problem in the reliability of the
module.
To protect OEL display modules from performance drops by static electricity
rapture, etc., do not touch the following sections whenever possible while
handling the OEL display modules.
* Pins and electrodes
* Pattern layouts such as the FPC
With this OEL display module, the OEL driver is being exposed. Generally
speaking, semiconductor elements change their characteristics when light is
radiated according to he principle of the solar battery. Consequently, if this
OEL driver is exposed to light, malfunctioning may occur.
* Design the product and installation method so that the OEL driver may be
shielded from light in actual usage.
* Design the product and installation method so that the OEL driver may be
shielded from light during the inspection processes.
Although this OEL display module stores the operation state data by the
commands and the indication data, when excessive external noise, etc. enters
into the module, the internal status may be changed. It therefore is necessary
to take appropriate measures to suppress noise generation or to protect from
influences of noise on the system design.
We recommend you to construct its software to make periodical refreshment of
the operation statuses (re-setting of the commands and re-transference of the
display data) to cope with catastrophic noise.
URL: www.lcd-china.com
Document Name: ER-OLED0.84-1 Manual
Page:19