Download ICOP Technology Inc.

c.
In
gy
lo
no
ch
Te
P
User’s Manual
IC
O
HMI-043T-B
DMP Vortex86 EXm Processor
Compact Panel PC with 4.3” Touchscreen
HMI-043T-EM41N-B
HMI-043T-EM41B-B
HMI-043T-EM42N-B
HMI-043T-EM42B-B
HMI-043T User’s Manual
IUMHMI043T-01 Ver.1.0A Jul, 2014
i
REVISION
VERSION
2015/2/1
Version 1.0A
DESCRIPTION
New Release
IC
O
P
Te
ch
no
lo
gy
In
c.
DATE
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
i
COPYRIGHT
The information in this manual is subject to change without notice for continuous
improvement in the product. All rights are reserved. The manufacturer assumes no
responsibility for any inaccuracies that may be contained in this document, and makes
no commitment to update or to keep current the information contained in this manual.
c.
No part of this manual may be reproduced, copied, translated or transmitted, in whole
or in part, in any form or by any means without the prior written permission of the
ICOP Technology Inc.
gy
In
Copyright 2015 ICOP Technology Inc.
Manual # IUMHMI043T-B Ver.1.0A Feb, 2015
lo
TRADEMARKS ACKNOWLEDGMENT
no
Vortex86EXm is the registered trademark of DMP Electronics Inc. Other brand
names or product names appearing in this document are the properties and registered
trademarks of their respective owners. All names mentioned herewith are served for
identification purpose only.
ch
For more detailed information or if you are interested in other ICOP products, please
visit our official websites at:
USA: www.icoptech.com
Japan: www.icop.co.jp
GmbH: www.icoptech.eu
China: www.icop.com.cn
P




Te
 Global: www.icop.com.tw
O
For technical support or demo images of operating systems download, please visit our
websites at:
IC
 ICOP Technical Resource: http://tech.icop.com.tw/
 Software Support: http://www.icoptech.net/
This Manual is for the HMI-043T. Box Series
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
ii
SAFETY INFORMATION
 Read these Safety instructions carefully.
 Please carry the unit with both hands, handle carefully.
 Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
In
 Input voltage rated +12 ~ 24VDC (HMI-043T Box Series)
c.
 Do not expose your Panel PC to rain or moisture in order to prevent shock and fire
hazard.
 Operating temperature between -20~+60°C (-4F~+140°F).
gy
 Keep HMI-043T away from humidity.
 Never touch un-insulated terminals or wire unless your power adaptor is
disconnected.
no
lo
 Locate your Panel PC as close as possible to the socket outline for easy access
and to avoid force caused by entangling of your arms with surrounding cables
from the Panel PC.
 USB connectors are not supplied with Limited Power Sources.
WARNING!
Te
ch
 If the equipment is not used for a long time, disconnect it from the power source to
avoid damage by transient overvoltage.
IC
O
P
DO NOT ATTEMPT TO OPEN OR TO DISASSEMBLE THE CHASSIS (ENCASING) OF
THIS PRODUCT. PLEASE CONTACT YOUR DEALER FOR SERVICING FROM
QUALIFIED TECHNICIAN.
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
iii
Content
Content ............................................................................................................................. iv
Ch. 1 General Information ................................................................................................. 1
1.1 Product Description ................................................................................................. 2
c.
1.2 Product Specifications ............................................................................................. 3
1.3 Inspection standard for TFT-LCD Panel .................................................................. 5
In
1.4 Product Dimensions ................................................................................................ 7
1.5 Ordering Information................................................................................................ 8
gy
Ch. 2 System Installation .................................................................................................. 9
2.1 CPU Board Outline .................................................................................................10
lo
2.2 Connector Summary............................................................................................... 11
2.3 Connector Pin Assignments ...................................................................................12
no
2.4 External I/O Overview.............................................................................................15
Ch. 3 Driver Installation ....................................................................................................16
ch
3.1 HMI-043T Development Note .................................................................................18
IC
O
P
Te
Warranty...........................................................................................................................19
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
iv
c.
In
gy
lo
no
ch
1
Te
Ch.
O
P
General Information
1.1 Product Description
IC
1.2 Product Specifications
1.3 Inspection standard for TFT-LCD Panel
1.4 Product Dimensions
1.5 Odering Information
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
1
1.1 Product Description
ICOP Technology Inc. is proudly going to release a brand new HMI, which offers fanless
design, low power consumption, and IP65 front panel. The HMI-043T is powered by DMP
Vortex86Exm SoC, the new generation SoC of Vortex86 family, which is included
128MB/256MB memory and eMMC Flash memory. The resistive touch panel with LED
c.
backlight TFT LCD increases operation convenience and visibility in outdoor environments.
In
The ultra-compact and thin exterior design is perfect for the present demanding embedded
and productive applications.
gy
The new HMI-043T inherited PDX/PMX-series’ smooth appearance and ultra-texture
aluminum exterior design to make your industrial applications look more stylish. The versatile I/O
lo
ports, 10/100Mps Ethernet, RS/232/485 , GPIO and Can bus etc. can fulfill fundamental
functions. Our consistent advantages feature stable performance, extended working temperature
no
support, low power consumption and fanless design. The open frame model can be
accommodated connectivity requirements to industrial machine platforms and industrial
ch
automation equipment’s needs.
Te
HMI-043T is not only supporting DOS, Linux, and Windows Embedded CE, but also
compatible with Arduino platform, which is an open-source electronics prototyping platform
based on flexible, easy to use hardware and software to meet ready-to-market demand and
IC
O
P
provide competitive advantages for customers.
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
2
1.2 Product Specifications
HARDWARE SPECIFICATIONS
CPU
DMP Vortex86Exm 400MHz
BIOS
Coreboot
BIOS
c.
L1:16KB I-Cache, 16KB D-Cache
Cache
128MB / 256MB DDRIII onboard
Nand-Flash
512MB/1GB/2GB eMMC onboard (Optional)
Integrated 10/100Mbps Ethernet
Network
gy
Memory
In
L2: 4-way, 128KB L2 Cache
lo
Support IEEE 802.3AT, PoE/PD (Optional)
Serial Interface
RS-485 x 1
no
RS-232 x 1
ch
Can bus x 1 (Optional)
USB ports (Ver2.0) x 1
Te
USB
P
MECHANICAL & ENVIRONMENT
O
Power Requirement
IC
Power Consumption
Operating Temperature
+12 ~ 24VDC
+12V@1A
0~+50°C (+32~+122°F) /
-20~+60°C (-4~+140°F)
Storage Temperature
-30~+70°C (-22~ +158°F)
Operating Humidity
0% ~ 90% Relative Humidity, Non-Condensing
Dimensions
116.4 x 94.4 x 34.3mm (4.58 x 3.71 x 1.35 inches)
Weight
300g
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
3
LCD SPECIFICATIONS
Display Type
4.3” WQVGA TFT LCD
Backlight Unit
LED
Display Resolution
480(W) x 272(H)
2
2
350 cd/m
Contrast Ratio
450 : 1
Display Color
16.7M
Pixel Configuration
R.G.B Vertical Stripe
Viewing Direction
6 o’clock
Viewing Angle
Vertical 120 , Horizontal 140
gy
o
lo
o
no
TOUCHSCREEN
Analog Resistive
Resolution
Continuous
ch
Type
Transmittance
Controller
3H / Anti-Glare
80%
Te
Surface Properties
PS/2 interface
DOS/Linux / WinCE
1 million
IC
O
P
Software Driver
Durability
In
c.
Luminance (cd/m )
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
4
1.3 Inspection standard for TFT-LCD Panel
DEFECT TYPE
LIMIT
Ignore
0.15mm≦φ≦0.5mm
N≦4
0.5mm＜φ
N=0
0.03mm<W≦0.1mm, L≦5mm
N≦3
VISUAL
DEFECT
INTERNAL
1.0mm＜W, 1.5mm＜L
Ignore
In
0.15mm≦φ≦0.5mm
N≦2
0.5mm＜φ
It’ OK if mura is slight visible through 6%ND filter
A Grade
DARK DOT
ELECTRICAL
DEFECT
C Area
O Area
N≦0
N≦2
N≦2
TOTAL DOT
B Grade
Total
C Area
O Area
Total
Note3
N≦2
N≦2
N≦3
N≦5
Note2
N≦5
N≦8
lo
BRIGHT DOT
N≦3
N≦3
N≦3
N≦5
N≦6
N≦8
Note2
N≦1 pair
N≦1 pair
N≦1 pair
N≦1 pair
Note4
N≦4
LINE DEFECT
N≦1 pair
NOT ALLOWED
ch
THREE OR MORE
ADJACENT DOT
N≦0
no
TWO ADJACENT DOT
NOT ALLOWED
(1) One pixel consists of 3 sub-pixels, including R, G, and B dot. (Sub-pixel = Dot)
Te
(2) Little bright Dot acceptitable under 6% ND-Filter.
(3) If require G0 grand (Total dot N≦0), please contact region sales.
IC
O
P
[ Note 1 ] W: Width[mm]; L: Length[mm]; N: Number; φ: Average Diameter.
(a) White / Black Spot
(b) Polarizer Bubble
[ Note 2 ] Bright dot is defined through 6% transmission ND Filter as following.
HMI-043T-B User’s Manual
Note1
N=0
gy
Mura
Note1
N=0
φ＜0.15mm
POLARIZER
BUBBLE
Note1
c.
φ＜0.15mm
SPOT
FIBER
Note
IUMHMI043T-B Ver.1.0A Feb, 2015
5
c.
no
lo
gy
In
[ Note 3 ] Display area
C Area: Center of display area
O Area: Outer of display area
ch
[ Note 4 ] Judge the defect dot and the adjacent dot as following. Allow below (as A, B, C and D
status) adjacent defect dots, including bright and dark adjacent dot. And they will be counted 2 defect
dots in total quantity.
Te
A
C
P
RG RG RG RG RG RG
R Adjacent Dot
O
RG RG RG RG RG RG
R Defect Dot
IC
RG RG RG RG RG RG
B
D
The defects that are not defined above and considered to be problem shall be reviewed and
discussed by both parties.
Defects on the Black Matrix, out of Display area, are not considered as a defect or counted.
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
6
IC
O
P
Te
ch
no
lo
gy
In
c.
1.4 Product Dimensions
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
7
1.5 Ordering Information
DESCRIPTION
HMI-043T-EM41B-B01
4.3" HMI w/128MB/512MB eMMC
/USB/RS232/485/DC+12-24V
HMI-043T-EM41B-B02
4.3" HMI w/128MB/512MB eMMC
/USB/POE/RS232/485/DC+12-24V
HMI-043T-EM41B-BC1
4.3" HMI w/128MB/512MB eMMC/USB/CAN/DC+12-24V
gy
In
c.
PART NUMBER
PACKING LIST
PACKAGE
HMI-043T-EM41B-B01
HMI-043T-EM41B-B01 *1
HMI-043T-EM41B-B02
HMI-043T-EM41B-B02 *1
HMI-043T-EM41B-BC1
HMI-043T-EM41B-BC1 *1
IC
O
P
Te
ch
no
lo
PART NUMBER
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
8
c.
In
gy
lo
no
ch
2
Te
Ch.
P
System Installation
O
2.1 CPU Board Outline
IC
2.2 Connector Summary
2.3 Connector Pin Assignments
2.4 Connector I/O Overview
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
9
gy
In
c.
2.1 CPU Board Outline
J1A
no
lo
J1B
Te
ch
HMI-043T-B CPU Board
IC
O
P
J8
J2
J9
J3
LAN1
J6
J5
HMI-043T-B I/O Board
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
10
2.2 Connector Summary
Description
Type of Connections
Pin #
J1A
Expansion slot
1.27mm 32x2-pin female box header
64-pin
J1B
Expansion slot
1.27mm 32x2-pin female box header
64-pin
J2
USB
External USB Connector
6-pin
J3
USB
External USB Connector
J5
COM2 RS232/485 or CAN bus
External D-Sub Male Connector
9-pin
J6
COM2: RS232/485 setting
Pin Header, 2.54mm, 1x2
2-pin
J8
SD Card Slot (Optional)
Internal SD Card Socket
J9
Power Terminal Connector
External Power Plug
In
gy
lo
no
Ethernet
External RJ45 Connector
8-pin
Te
P
O
IC
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
6-pin
3-pin
ch
LAN1
c.
No.
11
2.3 Connector Pin Assignments
J1A/J1B: Expansion Slot
J1A2
J1B1
J1B2
Signal Name
Pin#
Signal Name
Pin#
Signal Name
Pin#
Signal Name
1
RSTDRV
2
GND
1
VCC_IN
2
VCC_IN
3
GP00
4
GP01
3
GP70
4
GP71
5
GP02
6
GP03
5
GP72
6
GP73
7
GP04
8
GP05
7
GP74
8
GP75
9
GP06
10
GP07
9
GP76
10
GP77
11
GP90
12
GP91
11
GP60
12
GP61
13
GP92
14
GP93
13
GP62
14
GP63
15
GP94
16
GP95
15
GP64
16
GP65
17
GP96
18
GP97
17
GP66
18
GP67
19
GND
20
GND
19
GND
20
GND
21
USBD1-
22
USBD2-
21
GP50
22
GP51
23
USBD1+
24
USBD2+
23
GP52
24
GP53
25
AGND
26
AGND
25
GP54
26
GP55
27
ADC_0
28
ADC_1
27
GP56
28
GP57
29
ADC_2
30
ADC_3
29
GP40
30
GP41
31
ADC_4
32
ADC_5
31
GP42
32
GP43
33
ADC_6
34
ADC_7
33
GP44
34
GP45
35
GND
36
GND
35
GP46
36
GP47
37
SATA_TX-
38
SATA_RX-
37
GND
38
GND
39
SATA_TX+
40
SATA_RX+
39
GP30
40
GP31
GND
42
HSYNC
41
GP32
42
GP33
VGA_R
44
VSYNC
43
GP34
44
GP35
VGA_G
46
PCIRST-
45
GP36
46
GP37
VGA_B
48
RESET-
47
GP20
48
GP21
49
GND
50
GND
49
GP22
50
GP23
51
LANTX-
52
LANRX-
51
GP24
52
GP25
53
LANTX+
54
LANRX+
53
GP26
54
GP27
55
VBATT
56
VCC1.8_OUT
55
GND
56
GND
57
GP80
58
GP81
57
GP10
58
GP11
59
GP82
60
GP83
59
GP12
60
GP13
61
GP84
62
GP85
61
GP14
62
GP15
63
GP86
64
GP87
63
GP16
64
GP17
45
HMI-043T-B User’s Manual
In
gy
lo
ch
Te
IC
47
P
43
O
41
c.
Pin#
no
J1A1
IUMHMI043T-B Ver.1.0A Feb, 2015
12
c.
In
gy
lo
no
ch
Te
P
O
IC
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
13
J2/J3: USB
J6: COM2: RS232/485 setting
Pin #
Signal Name
Pin #
Signal Name
1
VCC
OPEN
ENABLE RS-232
2
USB0-
CLOSE
ENABLE RS-485
3
USB0+
4
GND
5
GGND
6
GGND
Pin #
J5: COM2 RS-232/485
n
Name
#
#
DCD2/
1
2
RS485-
Signal
Name
RXD2/
RS485+
TXD2
4
DTR2
5
GND
6
DSR2
7
RTS2
8
CTS2
9
RI2
GND
3
FG
Pin
Signal
Pin
Signal
#
Name
#
Name
1
FTXD+
2
FTXD-
3
FRXIN+
4
NC
5
NC
6
FRXIN-
7
NC
8
NC
Te
ch
3
2
LAN1
lo
Pi
Signal
no
n
+12~24V
gy
(Change setting by J6 Jumper)
Pi
Signal Name
In
1
c.
J9: Power Connector DC-IN 24V
P
J5: CAN bus (Optional)
O
Pi
n
IC
#
Signal
Name
Pi
n
#
1
2
3
4
5
6
7
CAN H
Signal
Name
CAN L
8
9
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
14
gy
In
c.
2.4 Connector I/O Overview
no
10/100Mbps Ethernet
USB 2.0 PORT
RS-232/485 or CAN bus
IC
O
P
Te
ch
Power Switch
lo
SD Slot (Optional)
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
15
c.
In
gy
lo
no
ch
Te
P
3
O
IC
Ch.
Driver Installation
3.1 HMI-043T Development Note
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
16
VGA
Vortex86VGA is a programmable VGA controller in 22mm x 16mm LQFP
128 package. It integrates a PCIe bridge controller and a VGA controller
with 4M-Byte Pseudo SRAM memory (16-bit data width). It also
c.
incorporates 3.3V DVO digital interfaces to support a third party
LVDS/TMDS transmitter.
LAN
In
The Vortex86DX2 processor is integrated 10/100Mbps Ethernet controller
gy
that supports both 10/100BASE-T and allows direct connection to your
10/100Mbps Ethernet based Local Area Network for full interaction with
local servers, wide area networks such as the Internet.
I/O and IRQ settings can be done by software with the supplied utility
no
lo
software, or it can be set for Plug and Play compatibility. The controller
supports: Half / Full-Duplex Ethernet function to double channel
bandwidth, auto media detection.
ch
OPERATING SYSTEM SUPPORT
The HMI-043T provides the VGA and LAN drivers for DOS, Linux, and
Te
Windows CE, Please get the drivers from ICOP technical support URL:
tech.icop.com.tw
HMI-043T is an open-source embedded platform based on Vortex86EXm
IC
O
P
SoC, easy-to-use hardware and software integrated. This platform can
support many x86 O/S as well as those running on the original Arduino
base system.
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
17
3.1 HMI-043T Development Note
< WINDOWS DEVELOPMENT GUIDE >
Windows Embedded CE 6.0 BSP and development notes, please visit
technical website to get more information at http://tech.icop.com.tw/.
c.
< LINUX INSTALLATION NOTE>
IC
O
P
Te
ch
no
lo
gy
In
Please visit Linux technical website to get more information at
ftp://ftp.dmp.com.tw/Linux_DEMO/Vortex86_Linux_Support_List_revised.
htm.
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
18
Warranty
In
c.
This product is warranted to be in good working order for a period of one
year from the date of purchase. Should this product fail to be in good
working order at any time during this period, we will, at our option, replace
or repair it at no additional charge except as set forth in the following
terms. This warranty does not apply to products damaged by misuse,
modifications, accident or disaster. Vendor assumes no liability for any
damages, lost profits, lost savings or any other incidental or consequential
IC
O
P
Te
ch
no
lo
gy
damage resulting from the use, misuse of, originality to use this product.
Vendor will not be liable for any claim made by any other related party.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or
faxing the vendor and requesting a Return Merchandise Authorization
(RMA) number. Returned goods should always be accompanied by a
clear problem description.
All Trademarks appearing in this manuscript are registered trademark of their
respective owners. All Specifications are subject to change without notice.
© ICOP Technology Inc. 2015
HMI-043T-B User’s Manual
IUMHMI043T-B Ver.1.0A Feb, 2015
19