Download TDX - Topp Pro Professional Audio Gear
Transcript
TDX TDX26 PLUS PRESET DELAY MODE PREV NEXT ENTER EDIT ESC UTILITY CARD TDX26 PLUS A B 1 2 3 4 5 6 MUTE MUTE MUTE MUTE MUTE MUTE TDX SAFETY RELATED SYMBOLS Protective Ground Before turning the unit ON, make sure that it is connected to Ground. This is to prevent the risk of electric shock. Never cut internal or external Ground wires. Likewise, never remove Ground wiring from the Protective Ground Terminal. This symbol, wherever used, alerts you to the presence of un-insulated and dangerous voltages within the product enclosure. These are voltages that may be sufficient to constitute the risk of electric shock or death. This symbol, wherever used, alerts you to important operating and maintenance instructions. Operating Conditions Always install in accordance with the manufacturer's instructions. To avoid the risk of electric shock and damage, do not subject this product to any liquid/rain or moisture. Please read. Do not use this product when in close proximity to water. Protective Ground Terminal Do not install this product near any direct heat source. Do not block areas of ventilation. Failure to do so could result in fire. Keep product away from naked flames. AC mains (Alternating Current) AC mains (Alternating Current) Denotes the product is turned on. Denotes the product is turned off. WARNING Describes precautions that should be observed to prevent the possibility of death or injury to the user. CAUTION Describes precautions that should be observed to prevent damage to the product. Disposing of this product should not be placed in municipal waste but rather in a separate collection. WARNING Power Supply Ensure that the mains source voltage (AC outlet) matches the voltage rating of the product. Failure to do so could result in damage to the product and possibly the user. Unplug the product before electrical storms occur and when unused for long periods of time to reduce the risk of electric shock or fire. External Connection Always use proper ready-made insulated mains cabling (power cord). Failure to do so could result in shock/death or fire. If in doubt, seek advice from a registered electrician. Do Not Remove Any Covers Within the product are areas where high voltages may present. To reduce the risk of electric shock do not remove any covers unless the AC mains power cord is removed. Covers should be removed by qualified service personnel only. No user serviceable parts inside. Fuse To prevent fire and damage to the product, use only the recommended fuse type as indicated in this manual. Do not short-circuit the fuse holder. Before replacing the fuse, make sure that the product is OFF and disconnected from the AC outlet. IMPORTANT SAFETY INSTRUCTIONS Read these instructions Follow all instructions Keep these instructions. Do not discard. Heed all warnings. Only use attachments / accessories specified by the manufacturer. Power Cord and Plug Do not tamper with the power cord or plug. These are designed for your safety. Do not remove Ground connections! If the plug does not fit your AC outlet seek advice from a qualified electrician. Protect the power cord and plug from any physical stress to avoid risk of electric shock. Do not place heavy objects on the power cord. This could cause electric shock or fire. Cleaning When required, either blow off dust from the product or use a dry cloth. Do not use any solvents such as Benzol or Alcohol. For safety, keep product clean and free from dust. Servicing Refer all servicing to qualified service personnel only. Do not perform any servicing other than those instruct -ions contained within the User's Manual. The mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. Carts and stands - The component should be used only with a cart or stand that is recommended by the manufacturer. A component and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the component and cart combination to overturn. TDX 1.INTRODUCTION ........................................................................................................1 2.FEATURES ..................................................................................................................1 3.USEFUL DATE ............................................................................................................1 4.FRONT PANEL... ..........................................................................................................3 5.REAR PANEL.................................................................................................................5 6.SIGNAL PROCESSING...................................................................................................6 7.GETTING STARTED........................... ...........................................................................7 8.SYSTEM CONFIGURATION...........................................................................................8 9.FIRST SETUP................................................................................................................10 10.DISPLAY INFORMATION IN DEFAULT CONDITIONS....................................................11 11.MENU MAP ..............................................................................................................14 12.PRESET MENU ..........................................................................................................18 13.DELAY MENU ...........................................................................................................22 14.EDIT MENU... ...........................................................................................................25 15.UTILITY MENU...........................................................................................................34 16.GANGING SUBMENU................................................................................................34 17.CONFIGURATIONS....................................................................................................43 18.CONNECTIONS..........................................................................................................46 19.FACTORY PRESETS ....................................................................................................53 20.TECHNICAL SPECIFICATIONS.....................................................................................54 21.GUARANTEE ...........................................................................................................55 22.NOTE ........................................................................................................................56 TDX Thank you for purchasing TOPP PRO product, the TDX26 PLUS. TDX26 PLUS is 2 In Digital Signal Processor for speaker management. For the input section, thereare Input Gain, 8 bands Parametric Equalizer(PEQ)and delay functions for the stereo input signal processing. In the 6 / 4 output channels section, there are equipped with Input selection, 5-band Parametric Equalizer, Crossover, Delay, Gain, Limiter,and Mute.In order to make the users understand the ways of operation conveniently, it uses the LEDs and LCD to indicate the respective parameter settings. Please read this manual carefully so you can take advantages of all the features of the TDX26 PLUS. Thanks again for choosing TOPP PRO. 2 balanced Inputs and 6 balanced Outputs 10 FACTORY PRESETS+64 USER PRESETS+128 CARD PRESETS 5 LEDs for every Channel Level Display Digital Audio Input with Sample Rate Converter Output Mute button for every output channel USB user interface for PC software control RS-485 multi-units linking interface Input Gain Control from -30 to +6 dB 5-band Input parametric EQ with 0.05 Oct. Frequency step 5-band Output parametric EQ with 0.05 Oct. Frequency step 900ms Inputs Delay and 291ms Outputs Delay Line Support for Speaker Placement Re-routable input selection for the output management Output Volume Control from -30 to +6 dB Comp/Lim Function for every output channel 0.5 dB /step for Parametric EQ Boost and Cut Auto-detectable Digital Input enable 1 TDX PRESET DELAY MODE PREV NEXT ENTER EDIT ESC UTILITY CARD TDX26 PLUS A B 1 2 3 4 5 6 MUTE MUTE MUTE MUTE MUTE MUTE USB 2 TDX 4 PRESET DELAY MODE PREV NEXT ESC UTILITY CARD , 3 ENTER EDIT TDX26 PLUS A B 1 2 3 4 5 6 MUTE MUTE MUTE MUTE MUTE MUTE TDX 4 TDX 5 AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN USB USB USB 5 RS485 OUT RS485 IN USB 6 5 4 3 2 1 INPUT B INPUT A TDX 6 6 TDX 7 7 TDX 8 TOPP PRO T DX 2 6 + 8 TDX 9 TDX 9 10 TDX 10 11 TDX TOPP PRO 12 TDX 13 TDX 11 14 TDX 15 TDX 16 TDX 17 TDX 12 18 TDX 19 TDX 20 TDX 21 TDX 13 22 TDX ~ ~ ~ ~ 23 TDX ~ ~ ~ ~ 24 TDX 14 ~ 25 TDX ~ ~ 26 TDX 27 TDX ~ ~ ~ 28 TDX 29 TDX ~ ~ ~ ~ 30 TDX ~ 31 TDX 32 TDX ~ 33 ~ TDX 15 16 34 TDX 35 TDX 36 TDX AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN 37 RS485 OUT RS485 IN USB 6 5 4 3 2 1 INPUT B INPUT A TDX TDX26 PLUS ~ ~ 38 TDX ~ 39 TDX 40 TDX 41 TDX 42 TDX 17 43 TDX 44 TDX 45 TDX 18 ~ USB USB 46 TDX AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN TDX26 PLUS 47 RS485 OUT RS485 IN USB 6 5 4 3 2 1 INPUT B INPUT A TDX AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN RS485 OUT RS485 IN USB 6 5 4 3 2 1 INPUT B INPUT A TDX26 PLUS 48 TDX AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN TDX26 PLUS 49 RS485 OUT RS485 IN USB 6 5 4 3 2 1 INPUT B INPUT A TDX OUTPUTS DIGITAL IN RS485 OUT RS485 IN USB 6 5 4 3 2 1 INPUT B INPUT A TDX26 PLUS 50 TDX TDX26 PLUS USB TDX26 PLUS USB AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN RS485 OUT RS485 IN 4 5 6 USB AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W 2 3 1 INPUT B INPUT A OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN RS485 OUT RS485 IN USB 6 5 4 AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W 3 2 1 INPUT B INPUT A 3 2 1 INPUT B INPUT A OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN 51 RS485 OUT RS485 IN USB 6 5 4 TDX TDX26 PLUS AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN RS485 OUT RS485 IN USB 6 5 4 3 2 1 INPUT B INPUT A 3 2 1 INPUT B INPUT A 3 2 1 INPUT B INPUT A 3 2 1 INPUT B INPUT A 3 2 1 INPUT B INPUT A USB USB AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN RS485 OUT RS485 IN USB TDX26 PLUS 6 5 4 USB AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN RS485 OUT RS485 IN USB 6 5 4 AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN RS485 OUT RS485 IN USB 6 5 4 AC INPUT: 100-240V~50/60Hz FUSE: T630mAL AC250V RATED POWER CONSUMPTION:14W OUTPUTS POWER ON Use only with a 250V fuse OFF DIGITAL IN RS485 OUT RS485 IN USB 6 5 4 52 TDX 19 53 TDX 20 ~ USB 54 TDX 21 GUARANTEE Topp Pro guarantees the normal operation of the product against any defect of manufacture and/or vice of material, by the term of (12) months, counted as of the date of purchase on the part of the user, committing itself to repair or to change, to its election, without position some, any piece or component that will fail in normal conditions of use within the mentioned period. This guarantee is valid if the original buyer will have to present /display this certificate properly sealed and signed by the selling house, accompanied by the corresponding invoice of purchase where it consisted the model and serial number of the acquired equipment. The guarantee does not cover: -Damages caused by the illegal use of the product, repair and/or nonauthorized modification conducted by people by Topp Pro. -Damages caused by the connection of the equipment to other equipment different from the specified ones in the manual of use, or by bad connection to these last ones. -Damages caused by electrical storms, blows and / or incorrect transport. -Damages caused by excesses or falls of tension in the network or by connection to networks with a tension different from the required one by the unit. -Damages caused by the presence of sand, acid of batteries, water, or any strange element inside the equipment. -Deteriorations produced by the course of the time, use and/or normal wear of the unit. -Alteraion or absence of the serial number of factory of the equipment. The repairs could only be carried out the authorized technical service by Topp Pro , that will inform about the term and other details into the repairs to take place according to this guarantee. Topp pro, will repair this unit in counted a term nongreater to 30 days as of the date of entrance of the unit to the Technical Service. In those cases in that due to the particularity of the spare part, outside necessary their import, the repair time and the viability of the same one will be subject to the effective norms for the import of parts, in which case one will inquire to the user about the term and possibility into repair. With the object of its correct operation, and of the validity of this one guarantee, this product will have to be installed and to be used according to the instructions that are detailed in the manual associate or the package of the product. This unit will be able to appear for its repair, next to the invoice of purchase (or any other comprobante where the date of purchase consists), to its authorized distributer Topp Pro or an authorized technical center on watch by Topp Pro. Exclusion of damages: THE RESPONSIBILITY OF TOPP PRO BY ANY DEFECTIVE PRODUCT IS LIMITED THE REPAIR OR THE REPLACEMENT OF HE HIMSELF, TO TOPP OPTION PRO. IF WE CHOSE TO REPLACE THE PRODUCT, THE REPLACEMENT CAN BE A RECONDITIONATED UNIT. TOPP PRO WILL NOT BE RESPONSIBLE BY THE DAMAGES BASED ON THE LOST, INCONVENIENCE, LOSS OF USE, BENEFITS, LOST SAVINGS, BY THE DAMAGE TO OTHER EQUIPMENT OR OTHER ARTICLES IN THE USE SITE, OR BY ANY OTHER DAMAGE IF HE IS FORTUITOUS, CONSEQUENT OR OF ANOTHER TYPE, ALTHOUGH TOPP PRO HAS BEEN NOTICED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow to exclusion or the limitation to the fortuitous or consequent damages, so the aforesaid limitation can not be applied to you. This guarantee gives specific legal rights him, you can also have other right that varies of state to state. 55 TDX 22 56 TDX