Download ELITE 60TM

ELITE 60
TM
User’s Manual
Covers getting to know your machine,
repairing an optical disc, maintenance,
menus, displays, & warranty coverage.
FOR SUPPORT INFORMATION
www
.v
enmill.com
www.v
.venmill.com
or
508-278-0091
866-864-0210
TOLL FREE
FOR NON-NORTH AMERICAN SERVICE
PLEASE CALL YOUR REGIONAL DISTRIBUTOR
If uncertain please contact [email protected]
E60M.PNV3000.111507.2
ELITE 60 1 Year Limited Warranty
TM
WARRANTY: VenMill Industries, Inc. (“VenMill”) warrants its
Elite 60™ product against defects in materials and workmanship
under normal use for a period beginning on the date of retail
purchase (the “Purchase Date”) by the original end-user
purchaser (the “Purchaser”) and ending on or upon the first to
occur of (i) the first anniversary of the Purchase Date or (ii) two
hundred (200) hours of product operation as measured by the
product’s internal usage tracking system (“Warranty Period”). If
a product defect arises and a valid warranty claim is received by
VenMill within the Warranty Period, at its option, VenMill will
either (1) repair the defect at no charge, using new or refurbished
replacement parts, (2) exchange the product with a new or
refurbished functionally equivalent product, or (3) refund the
purchase price of the product. A replacement product or part
assumes the remaining warranty of the original product. When
a defective product or part is exchanged, or a refund of the
purchase price is given, the applicable defective product or part
will become VenMill’s property and returned to VenMill at
VenMill’s request.
WARRANT Y EX
CL
USIONS AND LIMIT
ATIONS: This Limited
EXCL
CLUSIONS
LIMITA
Warranty applies only to Elite 60™ units manufactured by or for
VenMill that can be identified by the “VenMill” trademark, trade
name, or logo affixed to them and the unit serial number.
This Limited Warranty does not apply: (a) to damage caused by
failure to follow care and usage instructions supplied with the
product or improper maintenance; (b) to damage caused by
accident, abuse, misuse, neglect, flood, fire, lightning,
earthquake or other external or natural causes (such as
electrical fluctuations or power failure); (c) to damage caused
by operating the product outside the permitted or intended uses
described by VenMill; (d) to damage caused by service, repair or
product modifications performed by anyone not authorized by
VenMill; (e) to damage sustained during shipment; (f) to a
product or part that has been modified to significantly alter
functionality or capability; (g) to consumable parts, unless
damage has occurred due to a defect in materials or
workmanship; (h) to a product with a defaced or removed
VenMill serial number; (i) to a product offered for rental.
No VenMill reseller, agent, or employee is authorized to make
any modification, extension, or addition to this warranty.
TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY AND
REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS,
WHETHER ORAL OR WRITTEN, STATUTORY, EXPRESS OR IMPLIED.
AS PERMITTED BY APPLICABLE LAW, VENMILL SPECIFICALLY
DISCLAIMS ANY AND ALL STATUTORY OR IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS. IF VENMILL
CANNOT LAWFULLY DISCLAIM STATUTORY OR IMPLIED
WARRANTIES THEN TO THE EXTENT PERMITTED BY LAW, ALL SUCH
WARRANTIES SHALL BE LIMITED IN DURATION TO THE DURATION
OF THIS EXPRESS WARRANTY AND TO REPAIR OR REPLACEMENT
SERVICE AS DETERMINED BY VENMILL IN ITS SOLE DISCRETION.
16
SECTION 7
EXCEPT AS PROVIDED IN THIS WARRANTY AND TO THE EXTENT
PERMITTED BY LAW, VENMILL IS NOT RESPONSIBLE FOR DIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER
ANY OTHER LEGAL THEORY, OR ANY INDIRECT OR
CONSEQUENTIAL LOSS OR DAMAGE HOWSOEVER CAUSED
INCLUDING THE REPLACEMENT OF EQUIPMENT AND PROPERTY.
THE FOREGOING LIMITATION SHALL NOT APPLY TO DEATH OR
PERSONAL INJURY CLAIMS.
FOR PURCHASERS WHO ARE COVERED BY CONSUMER
PROTECTION LAWS OR REGULATIONS IN THEIR COUNTRY OF
PURCHASE OR, IF DIFFERENT, THEIR COUNTRY OF RESIDENCE,
THE BENEFITS CONFERRED BY THIS WARRANTY ARE IN ADDITION
TO ALL RIGHTS AND REMEDIES CONVEYED BY SUCH CONSUMER
PROTECTION LAWS AND REGULATIONS. Some countries, states
and provinces do not allow the exclusion or limitation of
incidental or consequential damages or exclusions or limitations
on the duration of implied warranties or conditions, so the above
limitations or exclusions may not apply to the Purchaser. This
warranty gives the Purchaser specific legal rights, and the
Purchaser may also have other rights that vary by country, state
or province. This Limited Warranty is governed by and construed
under the laws of the country in which the product purchase
took place.
OBT
AINING W
ARRANT Y SER
VICE
OBTAINING
WARRANT
SERVICE
VICE: To obtain warranty
service for the Elite 60™ product, the Purchaser needs to contact
regional distributor or if in North America VenMill Industries during
the Warranty Period either by phone at 800.928.0090 or 866864-0210 or by email to [email protected]. In order for
VenMill to process a warranty claim, the Purchaser will need to
provide to VenMill a copy of the dated sales receipt for the
product, the Purchaser’s name and address, the product serial
number and a description of the problem. If the Purchaser’s
claim appears to meet the criteria for warranty service, the
Purchaser will be given a return material authorization number
(RMA). Upon the issuance of the RMA to the Purchaser, the
Purchaser should bring or ship the product prepaid in the original
container, with any associated accessories, to VenMill at the
following address:
VenMill Industries, Inc.
RMA Number: (insert your RMA number here—see above)
660 Douglas Street
Uxbridge, MA 01569
or to such other address as a VenMill customer service
representative may provide to the Purchaser.
It is recommended that the Purchaser insure any product shipped
to VenMill.
SAVE ALL PACKING MATERIALS. FAILURE TO USE PACKAGING
DESIGNED FOR THIS UNIT, MAY CAUSE DAMAGE TO THE UNIT
AND WILL VOID WARRANTY.
FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT
WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY
VOIDING YOUR WARRANTY. FOR AUTHORIZED DISTRIBUTORS
VISIT WWW.VENMILL.COM.
VenMill Industries, Inc.
© 2007 VenMill Industries, Inc. All rights reserved.
Under the copyright laws, this manual may not be
copied, in whole or in part, without the written
consent of VenMill.
Every effort has been made to ensure that the
information in this manual is accurate. VenMill
is not responsible for printing or clerical errors.
VenMill Industries
660 Douglas Street
Uxbridge, MA 01569 U.S.A
508-278-0091
www.venmill.com
VenMill, Skip-Away, Elite 60 & OptoClear names and
designs are trademarks of VenMill Industries, Inc.
Artwork and Design © 2007 VenMill Industries, Inc.
All Rights Reserved.
The maximum amount of repairs per cartridge may
vary based on cleaning cycle usage. Blu-ray discs can
only be maintained, not repaired, due to the nature of
the disc. A disc adapter (included) will be needed for 3
inch disc repair or cleaning. See www.venmill.com for
more information.
CAUTION: Units and consumables are designed for
use in specific regions. Your warranty will be voided
if you purchase the equipment and/or consumables
outside of your designated region. Purchase only
through Authorized Distributors found on our website
at www.venmill.com. If uncertain, please contact
[email protected]
Note: Discs can be repaired an unlimited amount
of times. However, never run a disc two times
consecutively without letting the disc cool to room
temperature after each repair cycle.
Standard Maintenance
SECTION 6
Replacing the Buffing Wheel Cleaning Brush
It is recommended that you change the brush when the buffing wheels are replaced.
1 Turn off power and wait for the shutter to completely open.
2 Unplug the Elite 60TM power cord .
3 Remove the front drawer by pulling on the drawer handle.
4 Remove the buffing wheel out of the machine.
P
P
THANK YOU
For purchasing the Elite 60
TM
P
This unit is intended to clean/repair the
following discs: CD-Roms, Music CDs,
Data CDs, DVDs, HD-DVDs, Computer
5 Remove the brush by sliding it out.
6 Insert new brush.
7 Reinstall buffing wheel with label facing you.
8 It is recommended that you now clean your Elite 60 . (Please see pg. 15)
TM
Discs, Game Discs, Books on disc, all
recordable CDs and DVDs, double-sided
discs, & 3 Inch Discs (only with adapter).
N
O
9 Install the front drawer. Note: Push front drawer completely into machine or your
machine will not power on.
10 Plug in the Elite 60TM power cord and turn on the power.
FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY
VOIDING YOUR WARRANTY. FOR AUTHORIZED DISTRIBUTORS VISIT WWW.VENMILL.COM.
14
SAVE ALL PACKING MATERIALS. FAILURE TO USE
PACKAGING DESIGNED FOR THIS UNIT MAY CAUSE
DAMAGE TO THE UNIT AND WILL VOID WARRANTY.
FOR MORE INFO CONTACT [email protected].
VenMill Industries, Inc
660 Douglas Street
Uxbridge, MA 01569 USA
USA 800-928-0090
No. Am. 866-864-0210
Intl. 508-278-0091
Fax 508-278-0005
www.venmill.com
Standard Maintenance
Contents
SECTION 6
Replacing the OptoClearTM Cartridge
READ BEFORE OPERATING EQUIPMENT
CAUTION: never point empty or replacement cartridge nozzle at your face.
1 Turn off the power by pressing the power button and waiting for the shutter to
completely open.
2 Unscrew the spray nozzle counterclockwise and lift out the empty cartridge.
SECTION 1
Getting to Know Your Machine ............................................................................. 6
SECTION 2
Onscreen Displays ................................................................................................. 7
SECTION 3
Quick Start ............................................................................................................. 8
SECTION 4
Operation ............................................................................................................. 1 0
Operation Modes .................................................................................... 1 0
3 NOTE
NOTE: Do not remove or tamper with safety caution label or chip on cartridge.
Insert the new replacement cartridge into the Elite 60TM.
Using your 3 Inch Adapter ....................................................................... 1 0
4 Tighten the spray nozzle by turning clockwise.
SECTION 5
5 Remove safety caution label on new replacement cartridge.
Menu Screen ....................................................................................................... 1 1
6 Turn on the power.
SECTION 6
Standard Maintenance ....................................................................................... 1 2
Replacing the OptoClearTM Cartridge ................................................ 1 2
Replacing the Buffing Wheels ........................................................... 1 3
Cleaning the Buffing Wheels ............................................................. 1 3
Replacing the Buffing Wheel Cleaning Brush ................................... 1 4
Cleaning the Elite 60TM .......................................................................................................................... 1 5
The maximum amount of repairs per cartridge may vary based on cleaning cycle usage. Blu-ray discs can only be maintained, not repaired,
due to the nature of the disc. A disc adapter is required for 3 inch disc repair or cleaning. See www.venmill.com for more information.
CA
UTION
CAUTION
UTION: MAY BE HARMFUL IF SWALLOWED. EYE IRRITANT. CONTAINS: Isopropanol alcohol &
conditioning agent (catonic) PRECAUTIONS: Avoid ingestion. Keep away from eyes. Contents under
pressure. Temperature is not to exceed 120°F (49°C). Flammable. Keep away from flame. FIRST
AID: If eye contact occurs, rinse with tap water for 5-10 minutes. If irritation persists, seek medical care.
tridge pr
operly
If swallowed, drink full glass of water, get prompt medical attention. Dispose of car
cartridge
properly
operly..
FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY
VOIDING YOUR WARRANTY. FOR AUTHORIZED DISTRIBUTORS VISIT WWW.VENMILL.COM.
12
Cleaning the Drive Wheel .................................................................. 1 5
Error Codes ........................................................................................ 1 5
SECTION 7
Elite 60TM 1 Year Limited Warranty .................................................................... 1 6
Getting to Know Your Machine
SECTION 1
Menu Screen
SECTION 5
To Enter the Menu Screen
a
Press the scroll buttons while the machine is idle.
OPTOCLEAR CARTRIDGE
SPRAY NOZZLE
3 INCH ADAPTER HOLDER
PROTECTIVE SHUTTER
CARRYING HANDLE
Navigating the Menu Screen
a
b
The scroll buttons cycle through choices.
The repair button selects the highlighted option.
Menu Screen choices
DRAWER HANDLE
1
2
DISPLAY
MENU SCROLL BUTTONS
REPAIR BUTTON
POWER BUTTON
Blue = Repair mode
Green = Clean mode
Red Flashing = Error
Green = Power
Orange = Standby
3
4
5
6
7
8
9
CLN WHL – use this to perform an extended cleaning of the buffing wheel.*
CLN DRV – use this to perform an extended cleaning of the drive wheel.*
This may be necessary if the Disc is spinning roughly or improperly during a cycle.
WHL RPL – use this to indicate that the buffing wheel has been replaced.
LANGUAGE – use this to select the display language of your choice. (if available)
HOUR OP – use this option to display the total hours of cycle operation.
CHK SYS – use this option to test the functions of your Elite 60TM. This may be
used to determine where a failure has occurred.
SHIP – moves all mechanisms in position, including closing the shutter, in
preparation for shipping or transportation.
REPAIR C – Used when upgrading your firmware.
Exit – use this option to exit the menu screen.
* This process will take less than 2 minutes.
6
11
Operations
SECTION 4
Operation Modes
If 15 repair cycles are performed within a 30 minute period the machine could commence a 10
minute cool down. This will be indicated by a countdown timer on the display. Please do not unplug
the power cord during this cool-down period.
Note: Discs can be repaired an unlimited amount of times. However you should never run a disc two times
consecutively without letting the disc cool to room temperature after each repair cycle.
SECTION 2
Onscreen Display
1
The top line displays the machines status (Ready or Error Code) and cycle type (Repair
or Clean).
2
You can scroll through machine information by using the scroll buttons:
a Total Repairs, Total Cleans, Percentage of Cartridge remaining, Percentage of
Buffing wheel remaining, and the Menu Select.
3
The Middle line is the active line, when the word “MENU” is displayed (see section 5),
pressing the repair button will select the menu screen.
Quick Clean Mode
By default, the Elite 60TM when it is first powered on is in “Quick Clean Mode”. Inserting a disc will
result in a 15 second cleaning cycle being performed. (Repair button will be illuminated green)
Repair Mode
Onscreen Display
There are two ways to enter “Repair Mode”.
1. Before inserting a Disc press the repair button. When the repair button illuminates blue the
Elite 60TM will be in “Repair Mode”.
a
b
c
Inserting a disc will result in a 90 second repair.
During the repair cycle, pressing the up scroll button will increase the repair time.
Press once for 180 seconds and twice for 270 seconds. Pressing the down scroll button
will reduce the repair time. Pressing the repair button will end the cycle.
As long as the repair button is illuminated, the last selected cycle is in memory.
2. Insert a Disc into the Elite 60TM.
a
b
Machine will start a cleaning cycle.
Press the repair button during the cleaning cycle to switch to a repair cycle.
NOTE
NOTE: Once you have chosen a repair cycle the unit will remain in that cycle until you choose differently.
Standby Mode (hibernation)
When the machine is in Standby (hibernation) mode you can insert a disc at anytime into the
machine. There is no need to press the power button, the machine will automatically start up with
the last selected mode choice.
Using your 3 Inch Adapter
Match the label side of your 3 inch disc with
the open side of your 3 inch adapter. Slide the
disc into the 3 inner grooves making sure that
the disc is firmly clipped in place. The optical
side should be facing you.
Now insert your disc with adapter into your
unit, disc optical side down. After disc is
inserted make sure that your hands do
not obstruct the shutter from closing.
Shutter will open when cycle has finished
and your 3 inch disc with adapter will need
to be removed. Handle the disc only by the
edges or center ring of disc.
10
7
Quick Start
SECTION 3
1 Plug in the Elite 60TM power cord.
Quick Start
SECTION 3
5 Press the Repair Button.
WARNING!
Plug directly into outlet.
Do not use Extension Cords.
a
When the repair button is pressed, it
will illuminate blue, indicating a 90 second
repair is selected.
b
By default, the Elite 60TM when it is first
powered ON is in “Quick Clean Mode”.
Inserting a disc will result in a 15 second
cleaning cycle being performed.
For Repair Cycle see section 4.
Clean Mode: The repair button will be illuminated Green
Green.
2 Press the power button. The shutter will open completely.
Repair Mode: The repair button will be illuminated Blue
Blue.
6 Insert the Disc.
a
The Disc should be inserted straight in with label side up. It should be fully
inserted into the machine.
Note: 3 inch discs can only be repaired using a 3 inch adapter. (see section 4)
a
3 Select the language you want for
your display. (1st time use only, if available)
b
a
Use the scroll button to scroll through languages.
b
Use the repair button to select highlighted language.
O O
4 Remove the Disc installed
during shipping. (1st time use only)
a
N
Manually pull the disc straight
out of the machine.
Note: Discs can be repaired an unlimited
amount of times. However, never run a
disc two times consecutively without letting the disc cool to room temperature
after each repair cycle.
After the disc is inserted, make
sure that your hands do not
obstruct the shutter from closing.
c
Pressing the power button at any
time will end the cycle.
LABEL
SIDE
7 Remove the cleaned Disc.
a
8
b
Handle the disc only
by the edges or center ring.
9
Quick Start
SECTION 3
1 Plug in the Elite 60TM power cord.
Quick Start
SECTION 3
5 Press the Repair Button.
WARNING!
Plug directly into outlet.
Do not use Extension Cords.
a
When the repair button is pressed, it
will illuminate blue, indicating a 90 second
repair is selected.
b
By default, the Elite 60TM when it is first
powered ON is in “Quick Clean Mode”.
Inserting a disc will result in a 15 second
cleaning cycle being performed.
For Repair Cycle see section 4.
Clean Mode: The repair button will be illuminated Green
Green.
2 Press the power button. The shutter will open completely.
Repair Mode: The repair button will be illuminated Blue
Blue.
6 Insert the Disc.
a
The Disc should be inserted straight in with label side up. It should be fully
inserted into the machine.
Note: 3 inch discs can only be repaired using a 3 inch adapter. (see section 4)
a
3 Select the language you want for
your display. (1st time use only, if available)
b
a
Use the scroll button to scroll through languages.
b
Use the repair button to select highlighted language.
O O
4 Remove the Disc installed
during shipping. (1st time use only)
a
N
Manually pull the disc straight
out of the machine.
Note: Discs can be repaired an unlimited
amount of times. However, never run a
disc two times consecutively without letting the disc cool to room temperature
after each repair cycle.
After the disc is inserted, make
sure that your hands do not
obstruct the shutter from closing.
c
Pressing the power button at any
time will end the cycle.
LABEL
SIDE
7 Remove the cleaned Disc.
a
8
b
Handle the disc only
by the edges or center ring.
9
Operations
SECTION 4
Operation Modes
If 15 repair cycles are performed within a 30 minute period the machine could commence a 10
minute cool down. This will be indicated by a countdown timer on the display. Please do not unplug
the power cord during this cool-down period.
Note: Discs can be repaired an unlimited amount of times. However you should never run a disc two times
consecutively without letting the disc cool to room temperature after each repair cycle.
SECTION 2
Onscreen Display
1
The top line displays the machines status (Ready or Error Code) and cycle type (Repair
or Clean).
2
You can scroll through machine information by using the scroll buttons:
a Total Repairs, Total Cleans, Percentage of Cartridge remaining, Percentage of
Buffing wheel remaining, and the Menu Select.
3
The Middle line is the active line, when the word “MENU” is displayed (see section 5),
pressing the repair button will select the menu screen.
Quick Clean Mode
By default, the Elite 60TM when it is first powered on is in “Quick Clean Mode”. Inserting a disc will
result in a 15 second cleaning cycle being performed. (Repair button will be illuminated green)
Repair Mode
Onscreen Display
There are two ways to enter “Repair Mode”.
1. Before inserting a Disc press the repair button. When the repair button illuminates blue the
Elite 60TM will be in “Repair Mode”.
a
b
c
Inserting a disc will result in a 90 second repair.
During the repair cycle, pressing the up scroll button will increase the repair time.
Press once for 180 seconds and twice for 270 seconds. Pressing the down scroll button
will reduce the repair time. Pressing the repair button will end the cycle.
As long as the repair button is illuminated, the last selected cycle is in memory.
2. Insert a Disc into the Elite 60TM.
a
b
Machine will start a cleaning cycle.
Press the repair button during the cleaning cycle to switch to a repair cycle.
NOTE
NOTE: Once you have chosen a repair cycle the unit will remain in that cycle until you choose differently.
Standby Mode (hibernation)
When the machine is in Standby (hibernation) mode you can insert a disc at anytime into the
machine. There is no need to press the power button, the machine will automatically start up with
the last selected mode choice.
Using your 3 Inch Adapter
Match the label side of your 3 inch disc with
the open side of your 3 inch adapter. Slide the
disc into the 3 inner grooves making sure that
the disc is firmly clipped in place. The optical
side should be facing you.
Now insert your disc with adapter into your
unit, disc optical side down. After disc is
inserted make sure that your hands do
not obstruct the shutter from closing.
Shutter will open when cycle has finished
and your 3 inch disc with adapter will need
to be removed. Handle the disc only by the
edges or center ring of disc.
10
7
Getting to Know Your Machine
SECTION 1
Menu Screen
SECTION 5
To Enter the Menu Screen
a
Press the scroll buttons while the machine is idle.
OPTOCLEAR CARTRIDGE
SPRAY NOZZLE
3 INCH ADAPTER HOLDER
PROTECTIVE SHUTTER
CARRYING HANDLE
Navigating the Menu Screen
a
b
The scroll buttons cycle through choices.
The repair button selects the highlighted option.
Menu Screen choices
DRAWER HANDLE
1
2
DISPLAY
MENU SCROLL BUTTONS
REPAIR BUTTON
POWER BUTTON
Blue = Repair mode
Green = Clean mode
Red Flashing = Error
Green = Power
Orange = Standby
3
4
5
6
7
8
9
CLN WHL – use this to perform an extended cleaning of the buffing wheel.*
CLN DRV – use this to perform an extended cleaning of the drive wheel.*
This may be necessary if the Disc is spinning roughly or improperly during a cycle.
WHL RPL – use this to indicate that the buffing wheel has been replaced.
LANGUAGE – use this to select the display language of your choice. (if available)
HOUR OP – use this option to display the total hours of cycle operation.
CHK SYS – use this option to test the functions of your Elite 60TM. This may be
used to determine where a failure has occurred.
SHIP – moves all mechanisms in position, including closing the shutter, in
preparation for shipping or transportation.
REPAIR C – Used when upgrading your firmware.
Exit – use this option to exit the menu screen.
* This process will take less than 2 minutes.
6
11
Standard Maintenance
Contents
SECTION 6
Replacing the OptoClearTM Cartridge
READ BEFORE OPERATING EQUIPMENT
CAUTION: never point empty or replacement cartridge nozzle at your face.
1 Turn off the power by pressing the power button and waiting for the shutter to
completely open.
2 Unscrew the spray nozzle counterclockwise and lift out the empty cartridge.
SECTION 1
Getting to Know Your Machine ............................................................................. 6
SECTION 2
Onscreen Displays ................................................................................................. 7
SECTION 3
Quick Start ............................................................................................................. 8
SECTION 4
Operation ............................................................................................................. 1 0
Operation Modes .................................................................................... 1 0
3 NOTE
NOTE: Do not remove or tamper with safety caution label or chip on cartridge.
Insert the new replacement cartridge into the Elite 60TM.
Using your 3 Inch Adapter ....................................................................... 1 0
4 Tighten the spray nozzle by turning clockwise.
SECTION 5
5 Remove safety caution label on new replacement cartridge.
Menu Screen ....................................................................................................... 1 1
6 Turn on the power.
SECTION 6
Standard Maintenance ....................................................................................... 1 2
Replacing the OptoClearTM Cartridge ................................................ 1 2
Replacing the Buffing Wheels ........................................................... 1 3
Cleaning the Buffing Wheels ............................................................. 1 3
Replacing the Buffing Wheel Cleaning Brush ................................... 1 4
Cleaning the Elite 60TM .......................................................................................................................... 1 5
The maximum amount of repairs per cartridge may vary based on cleaning cycle usage. Blu-ray discs can only be maintained, not repaired,
due to the nature of the disc. A disc adapter is required for 3 inch disc repair or cleaning. See www.venmill.com for more information.
CA
UTION
CAUTION
UTION: MAY BE HARMFUL IF SWALLOWED. EYE IRRITANT. CONTAINS: Isopropanol alcohol &
conditioning agent (catonic) PRECAUTIONS: Avoid ingestion. Keep away from eyes. Contents under
pressure. Temperature is not to exceed 120°F (49°C). Flammable. Keep away from flame. FIRST
AID: If eye contact occurs, rinse with tap water for 5-10 minutes. If irritation persists, seek medical care.
tridge pr
operly
If swallowed, drink full glass of water, get prompt medical attention. Dispose of car
cartridge
properly
operly..
FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY
VOIDING YOUR WARRANTY. FOR AUTHORIZED DISTRIBUTORS VISIT WWW.VENMILL.COM.
12
Cleaning the Drive Wheel .................................................................. 1 5
Error Codes ........................................................................................ 1 5
SECTION 7
Elite 60TM 1 Year Limited Warranty .................................................................... 1 6
Standard Maintenance
SECTION 6
Replacing the Buffing Wheel
1 Turn off power and wait for the shutter to completely open.
2 Unplug the Elite 60TM power cord.
3 Remove the front drawer by pulling on the drawer handle.
4 Remove the worn buffing wheel by pulling them away from the buffing motor.
5 Install the new buffing wheel. Ensure it is fully seated against the back
of the buffing motor spindle with label facing towards you.
6 It is recommended that you now clean your Elite 60TM and change your cleaning
brushes. (Please see pgs 14 & 15.)
7 Install the front drawer. Note: Push front drawer completely into machine or your
machine will not power on.
8 Plug in the Elite 60TM power cord and turn on the power.
9 Enter the menu screen and choose “WHL RPL”. Resume normal operation.
The maximum amount of repairs may vary based on cleaning cycle usage. Blu-ray discs can only be maintained, not repaired, due
to the nature of the disc. A disc adapter is required for 3 inch disc repair or cleaning. See www.venmill.com for more information.
Cleaning the Buffing Wheel
This process will take less than 2 minutes.
This may be necessary if the Discs are coming out with a film or poor finish.
1 Ensure that there is no Disc in the Unit
2 Enter the menu screen and select “CLN WHL”. Then push Repair Button to activate.
FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY
VOIDING YOUR WARRANTY. FOR AUTHORIZED DISTRIBUTORS VISIT WWW.VENMILL.COM.
13
Standard Maintenance
SECTION 6
Replacing the Buffing Wheel Cleaning Brush
It is recommended that you change the brush when the buffing wheels are replaced.
1 Turn off power and wait for the shutter to completely open.
2 Unplug the Elite 60TM power cord .
3 Remove the front drawer by pulling on the drawer handle.
4 Remove the buffing wheel out of the machine.
P
P
THANK YOU
For purchasing the Elite 60
TM
P
This unit is intended to clean/repair the
following discs: CD-Roms, Music CDs,
Data CDs, DVDs, HD-DVDs, Computer
5 Remove the brush by sliding it out.
6 Insert new brush.
7 Reinstall buffing wheel with label facing you.
8 It is recommended that you now clean your Elite 60 . (Please see pg. 15)
TM
Discs, Game Discs, Books on disc, all
recordable CDs and DVDs, double-sided
discs, & 3 Inch Discs (only with adapter).
N
O
9 Install the front drawer. Note: Push front drawer completely into machine or your
machine will not power on.
10 Plug in the Elite 60TM power cord and turn on the power.
FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY
VOIDING YOUR WARRANTY. FOR AUTHORIZED DISTRIBUTORS VISIT WWW.VENMILL.COM.
14
SAVE ALL PACKING MATERIALS. FAILURE TO USE
PACKAGING DESIGNED FOR THIS UNIT MAY CAUSE
DAMAGE TO THE UNIT AND WILL VOID WARRANTY.
FOR MORE INFO CONTACT [email protected].
VenMill Industries, Inc
660 Douglas Street
Uxbridge, MA 01569 USA
USA 800-928-0090
No. Am. 866-864-0210
Intl. 508-278-0091
Fax 508-278-0005
www.venmill.com
Standard Maintenance
SECTION 6
Cleaning the Elite 60TM
Recommended with every cartridge change.
1 Turn off power and wait for the shutter to completely open.
2 Unplug the Elite 60TM power cord.
3 Remove the front drawer by pulling on the drawer handle.
4 Remove any lint contained in the machine.
You may use compressed air, a gentle vacuum, or your hand.
P
5 Install the front drawer. Note: Push front drawer completely into machine or your
machine will not power on.
6 Plug in the Elite 60TM power cord and turn on the power.
Cleaning the Drive Wheel
This may be necessary if the Disc is spinning roughly or improperly during the cycle.
1 Ensure that there is no Disc in the Unit.
2 Enter the menu screen and select “CLN DRV”.*
* This process will take less than 2 minutes.
Error Codes
1
2
3
4
5
6
7
8
9
WHEEL CHG – Change the buffing wheel
CART CHG – Change the OptoClearTM cartridge
CART LOW – Cartridge is below 10% capacity
E0001 – Shutter not closed, contact technical support
E0002 – Shutter not open, contact technical support
E0003 – Buffing motor not centered, contact technical support
E0004 – Lift wedge not in home position, contact technical support
E0005 – Disc not turning - try cleaning the Drive Wheel
E0006 – Cannot increase disc surface temperature sufficiently for repair.
15
ELITE 60 1 Year Limited Warranty
TM
WARRANTY: VenMill Industries, Inc. (“VenMill”) warrants its
Elite 60™ product against defects in materials and workmanship
under normal use for a period beginning on the date of retail
purchase (the “Purchase Date”) by the original end-user
purchaser (the “Purchaser”) and ending on or upon the first to
occur of (i) the first anniversary of the Purchase Date or (ii) two
hundred (200) hours of product operation as measured by the
product’s internal usage tracking system (“Warranty Period”). If
a product defect arises and a valid warranty claim is received by
VenMill within the Warranty Period, at its option, VenMill will
either (1) repair the defect at no charge, using new or refurbished
replacement parts, (2) exchange the product with a new or
refurbished functionally equivalent product, or (3) refund the
purchase price of the product. A replacement product or part
assumes the remaining warranty of the original product. When
a defective product or part is exchanged, or a refund of the
purchase price is given, the applicable defective product or part
will become VenMill’s property and returned to VenMill at
VenMill’s request.
WARRANT Y EX
CL
USIONS AND LIMIT
ATIONS: This Limited
EXCL
CLUSIONS
LIMITA
Warranty applies only to Elite 60™ units manufactured by or for
VenMill that can be identified by the “VenMill” trademark, trade
name, or logo affixed to them and the unit serial number.
This Limited Warranty does not apply: (a) to damage caused by
failure to follow care and usage instructions supplied with the
product or improper maintenance; (b) to damage caused by
accident, abuse, misuse, neglect, flood, fire, lightning,
earthquake or other external or natural causes (such as
electrical fluctuations or power failure); (c) to damage caused
by operating the product outside the permitted or intended uses
described by VenMill; (d) to damage caused by service, repair or
product modifications performed by anyone not authorized by
VenMill; (e) to damage sustained during shipment; (f) to a
product or part that has been modified to significantly alter
functionality or capability; (g) to consumable parts, unless
damage has occurred due to a defect in materials or
workmanship; (h) to a product with a defaced or removed
VenMill serial number; (i) to a product offered for rental.
No VenMill reseller, agent, or employee is authorized to make
any modification, extension, or addition to this warranty.
TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY AND
REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS,
WHETHER ORAL OR WRITTEN, STATUTORY, EXPRESS OR IMPLIED.
AS PERMITTED BY APPLICABLE LAW, VENMILL SPECIFICALLY
DISCLAIMS ANY AND ALL STATUTORY OR IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS. IF VENMILL
CANNOT LAWFULLY DISCLAIM STATUTORY OR IMPLIED
WARRANTIES THEN TO THE EXTENT PERMITTED BY LAW, ALL SUCH
WARRANTIES SHALL BE LIMITED IN DURATION TO THE DURATION
OF THIS EXPRESS WARRANTY AND TO REPAIR OR REPLACEMENT
SERVICE AS DETERMINED BY VENMILL IN ITS SOLE DISCRETION.
16
SECTION 7
EXCEPT AS PROVIDED IN THIS WARRANTY AND TO THE EXTENT
PERMITTED BY LAW, VENMILL IS NOT RESPONSIBLE FOR DIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER
ANY OTHER LEGAL THEORY, OR ANY INDIRECT OR
CONSEQUENTIAL LOSS OR DAMAGE HOWSOEVER CAUSED
INCLUDING THE REPLACEMENT OF EQUIPMENT AND PROPERTY.
THE FOREGOING LIMITATION SHALL NOT APPLY TO DEATH OR
PERSONAL INJURY CLAIMS.
FOR PURCHASERS WHO ARE COVERED BY CONSUMER
PROTECTION LAWS OR REGULATIONS IN THEIR COUNTRY OF
PURCHASE OR, IF DIFFERENT, THEIR COUNTRY OF RESIDENCE,
THE BENEFITS CONFERRED BY THIS WARRANTY ARE IN ADDITION
TO ALL RIGHTS AND REMEDIES CONVEYED BY SUCH CONSUMER
PROTECTION LAWS AND REGULATIONS. Some countries, states
and provinces do not allow the exclusion or limitation of
incidental or consequential damages or exclusions or limitations
on the duration of implied warranties or conditions, so the above
limitations or exclusions may not apply to the Purchaser. This
warranty gives the Purchaser specific legal rights, and the
Purchaser may also have other rights that vary by country, state
or province. This Limited Warranty is governed by and construed
under the laws of the country in which the product purchase
took place.
OBT
AINING W
ARRANT Y SER
VICE
OBTAINING
WARRANT
SERVICE
VICE: To obtain warranty
service for the Elite 60™ product, the Purchaser needs to contact
regional distributor or if in North America VenMill Industries during
the Warranty Period either by phone at 800.928.0090 or 866864-0210 or by email to [email protected]. In order for
VenMill to process a warranty claim, the Purchaser will need to
provide to VenMill a copy of the dated sales receipt for the
product, the Purchaser’s name and address, the product serial
number and a description of the problem. If the Purchaser’s
claim appears to meet the criteria for warranty service, the
Purchaser will be given a return material authorization number
(RMA). Upon the issuance of the RMA to the Purchaser, the
Purchaser should bring or ship the product prepaid in the original
container, with any associated accessories, to VenMill at the
following address:
VenMill Industries, Inc.
RMA Number: (insert your RMA number here—see above)
660 Douglas Street
Uxbridge, MA 01569
or to such other address as a VenMill customer service
representative may provide to the Purchaser.
It is recommended that the Purchaser insure any product shipped
to VenMill.
SAVE ALL PACKING MATERIALS. FAILURE TO USE PACKAGING
DESIGNED FOR THIS UNIT, MAY CAUSE DAMAGE TO THE UNIT
AND WILL VOID WARRANTY.
FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT
WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY
VOIDING YOUR WARRANTY. FOR AUTHORIZED DISTRIBUTORS
VISIT WWW.VENMILL.COM.
VenMill Industries, Inc.
© 2007 VenMill Industries, Inc. All rights reserved.
Under the copyright laws, this manual may not be
copied, in whole or in part, without the written
consent of VenMill.
Every effort has been made to ensure that the
information in this manual is accurate. VenMill
is not responsible for printing or clerical errors.
VenMill Industries
660 Douglas Street
Uxbridge, MA 01569 U.S.A
508-278-0091
www.venmill.com
VenMill, Skip-Away, Elite 60 & OptoClear names and
designs are trademarks of VenMill Industries, Inc.
Artwork and Design © 2007 VenMill Industries, Inc.
All Rights Reserved.
The maximum amount of repairs per cartridge may
vary based on cleaning cycle usage. Blu-ray discs can
only be maintained, not repaired, due to the nature of
the disc. A disc adapter (included) will be needed for 3
inch disc repair or cleaning. See www.venmill.com for
more information.
CAUTION: Units and consumables are designed for
use in specific regions. Your warranty will be voided
if you purchase the equipment and/or consumables
outside of your designated region. Purchase only
through Authorized Distributors found on our website
at www.venmill.com. If uncertain, please contact
[email protected]
Note: Discs can be repaired an unlimited amount
of times. However, never run a disc two times
consecutively without letting the disc cool to room
temperature after each repair cycle.
ELITE 60
TM
User’s Manual
Covers getting to know your machine,
repairing an optical disc, maintenance,
menus, displays, & warranty coverage.
FOR SUPPORT INFORMATION
www
.v
enmill.com
www.v
.venmill.com
or
508-278-0091
866-864-0210
TOLL FREE
FOR NON-NORTH AMERICAN SERVICE
PLEASE CALL YOUR REGIONAL DISTRIBUTOR
If uncertain please contact [email protected]
E60M.PNV3000.111507.2