Download Manual - Controllux

POWER
Dotz Par
Dotz Par
Photometrics
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
Intensity(LUX)
165
139
223
500
44
39
55
130
21
19
27
60
13
12
17
36
Set Up
Notice: Be sure
to DMX512
follow figures two and three when making your own
DMX+,DMX-,COMMON
Beam angle 60°
Field angle 80°
Red LEDs
Green LEDs
Blue LEDs
Full LEDs
9
8
11
24
4
COMMON
3
Beam opening(m)
1
SOUND
0
60
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
REMOTE
CONTROL
SOUND
80
OUTPUT
1 Ground
3
DMX -
1
2
SOUND
XLR Female Socket
2 Cold
2 Cold
1 Ground
1
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
INPUT
3
Figure 2
OUTPUT
1
2
Termination redu
avoids signal tra
and interference.
to connect a DMX
120 Ohm 1/4 W)
and PIN 3 (DMX
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
3 Hot
3
Figure 3
POWER
4
0
1
60° Diameter(m) 1.15
80° Diameter(m) 1.68
2
2.35
3.35
3
4
3.45
5.03
4.60
6.70
DMX512
DMX+,DMX-,COMMON
Beam angle 25°
Field angle 35°
Intensity(LUX)
1074
915
1590
3180
290
259
466
970
140
127
238
465
83
71
135
266
56
55
84
175
3
COMMON
DMX512 OUT
3-PIN XLR
1
2
3
2
3 Hot
Pin 3 = Data True (positive)
POWER
POWER
Special Note: Line Termination. When longer runs of cable are
5
5.75
8.40
Lens Off
Beam opening(m)
INPUT
2
DMX +
3
XLRINPUT
Male Socket
2
DMX +
DMX -
3
1
2
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
DMX512 IN
3-PIN XLR
3
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
1
0
25
35
1
2
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
3
0
1
DMX512 OUT
3-PIN XLR
2
Red LEDs
Green LEDs
Blue LEDs
Full LEDs
POWER
1
25° Diameter(m) 0.45
35° Diameter(m) 0.63
2
0.88
1.25
3
4
1.33
1.90
1.77
2.50
5
2.21
3.15
Lens On
ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 17
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Do Not Use
Not Used
Do Not Use
ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 6