1
Download Cycle end - PTB Sales
Transcript
C 110 Cycle end Purpose of the cycle end Automatic control of the roughing time and measure time i.e. the end of cycle. ■ Cycle end: operator Operator stops the cycle ( ). ■ Cycle end: automatic Cycle is stopped automatically. CYCLE The default value is « operator ». Note: If Cycle end is automatic, both parameters roughing and measure times are automatic. Do you have access to this operation /function? Access authorization Activate the cycle end Reminder C 30 Operating principle of the control panel Press the key C 20 activated SET POINTS F1 AUDIO DIGITAL VOICE :3 :5 F2 F3 GB 00267 - Edition 03 - September 01 F4 F1 NEXT CYCLE END: operator F2 F2 F3 F4 x3 F1 + F1 F1 F3 CYCLE END:automatic *****ROUGHING***** OVERLAP TIMER: no TIMER (min:s):00:09 F2 F4 Activate and adjust roughing timer: please follow the procedure described below. Alcatel Vacuum Technology France - ASM 182 TD+ - ASM 192 T2D+ User’s Manual 1/3 C 110 Cycle end Roughing timer If Cycle end is activated (automatic), user could activate or not the roughing timer. Roughing timer determines maximum authorized roughing time before the tested part is considered as bad. To consider the tested part as bad, it is necessary to activate the Memo function. ➪ see below ➪ see "Measure" paragraph. Activate the roughing timer F1 F3 F3 + F3 F1 F3 F1 F4 F3 Adjust roughing timer. F1 F3 CYCLE END:automatic *****ROUGHING***** OVERLAP TIMER: no TIMER (min:s):00:09 F2 CYCLE END:automatic *****ROUGHING***** OVERLAP TIMER: yes TIMER (min:s):00:09 F2 CYCLE END:automatic *****ROUGHING***** OVERLAP TIMER: yes TIMER (min:s):00:09 F2 CYCLE END:automatic *****ROUGHING***** OVERLAP TIMER: yes TIMER (min:s):00:05 F2 Adjustment of a value F4 F1 F3 F4 F4 F4 F4 C 20 CYCLE END:automatic *****ROUGHING***** OVERLAP TIMER: yes TIMER (min:s):00:05 F2 F4 Adjust measure timer: see “Measure” paragraph. Please follow the procedure with “Memo function” paragraph. Measure If Cycle end is activated (automatic), user should adjust the measure timer i.e. the cycle end. The measure timer corresponds to the time allowed to the leak detector to remain in test. When it is reached, the measure flashes. 2/3 Alcatel Vacuum Technology France - ASM 182 TD+ - ASM 192 T2D+ User’s Manual GB 00267 - Edition 03 - September 01 Activate the roughing timer ■ Not activate the roughing timer ■ C 110 Cycle end F1 Measure (Continued) F3 NEXT F1 F3 F1 F4 F3 F1 Adjust measure timer. F3 CYCLE END:automatic *****ROUGHING***** OVERLAP TIMER: no TIMER (min:s):00:09 F1 F3 F4 CYCLE END:automatic *****MEASURE***** F2 TIMER (min:s):00:06 F4 CYCLE END:automatic *****MEASURE***** F2 TIMER (min:s):00:06 F4 CYCLE END:automatic *****MEASURE***** F2 TIMER (min:s):00:10 F4 Adjustment of a value F4 F2 C 20 CYCLE END:automatic *****MEASURE***** F2 TIMER (min:s):00:10 F4 Access to memo function: please follow the procedure with “memo function” paragraph. Memo function Without leaving the SET POINTS Menu, user can adjust Memo function if necessary: ■ Not access to memo function F1 SET POINTS F3 F1 F3 CYCLE END:automatic *****MEASURE***** F2 TIMER (min:s):00:10 F4 READY FOR CYCLE (Automatic end) INLET ... F2 GB 00267 - Edition 03 - September 01 F4 ■ Access to memo function F1 F3 NEXT F1 F1 F3 CYCLE END:automatic *****MEASURE***** F2 TIMER (min:s):00:10 F4 MEMO FUNCTION ACTIVE: no DISPLAY TIMER : NO TIMER (min:s):00:06 F2 To adjust memo function Deactivate the cycle end F4 C 130 The procedure is the same as for activating the Cycle end but instead of pressing , press . Alcatel Vacuum Technology France - ASM 182 TD+ - ASM 192 T2D+ User’s Manual 3/3
