Download Modbus Option Board

2 • vacon
index
INDEX
Document code: DPD00894A
Date:17.01.2012
1.
GENERAL ........................................................................................................................... 4
2.
INSTALLATION ................................................................................................................... 5
3.
CONNECTIONS ................................................................................................................... 7
3.1
4.
Jumper settings ....................................................................................................................... 7
3.1.1 Jumper settings of 4CMO board with OPT-CG: ............................................................... 7
3.1.2 Jumper settings of 4CM board with OPT-CG: .................................................................. 8
COMMISSIONING ................................................................................................................ 9
4.1
4.2
Parameters............................................................................................................................... 9
LED indications ......................................................................................................................... 9
5.
OPT-CG Config tool .......................................................................................................... 10
6.
Selma application (APFIEN04) .......................................................................................... 12
6.1
6.2
6.3
Introduction ............................................................................................................................ 12
Control I/O .............................................................................................................................. 13
“Terminal to function” (TTF) programming principle ............................................................ 14
6.3.1 Defining an input/output for a certain function on keypad ............................................ 14
6.3.2 Defining a terminal for a certain function with NCDrive programming tool ................. 15
6.4
Selma Application – Parameter lists ..................................................................................... 16
6.4.1 M1 > V1.1 Monitor page 1 ............................................................................................... 17
6.4.2 M1>V1.2 Monitor Page 2 ................................................................................................. 17
6.4.3 Basic parameters ........................................................................................................... 19
6.4.4 Input signals (Control keypad: Menu M2 G2.2) ........................................................... 20
6.4.5 Output signals (Control keypad: Menu M2  G2.3) ....................................................... 24
6.4.6 Reference handling (Control keypad: Menu M2  G2.4) ............................................... 26
6.4.7 Ramp functions (Control keypad: Menu M2  G2.5) ..................................................... 27
6.4.8 Drive control (Control keypad: Menu M2  G2.6) .......................................................... 28
6.4.9 Motor control (Control keypad: Menu M2  G2.7) ......................................................... 30
6.4.10
Limit settings (Control keypad: Menu M2  G2.8)..................................................... 32
6.4.11
Speed control (Control keypad: Menu M2  G2.9) .................................................... 33
6.4.12
Oscillation damp (Control keypad: Menu M2  G2.10) .............................................. 34
6.4.13
Brake & fan control (Control keypad: Menu M2 G2.11) .......................................... 34
6.4.14
Master Follower (Control keypad: Menu M2  G2.12) .............................................. 35
6.4.15
Protections (Control keypad: Menu M2  G2.13) ...................................................... 35
6.4.16
Flux reference handling (Control keypad: Menu M2  G2.14) .................................. 37
6.4.17
Startup torque (Control keypad: Menu M2  G2.15) ................................................. 37
6.4.18
DAC (Control keypad: Menu M2  G2.16) .................................................................. 38
6.4.19
Data mapping (Control keypad: Menu M2  G2.17) .................................................. 38
6.4.20
Keypad control (Control keypad: Menu M3  R3.1) .................................................. 38
6.4.21
Expander boards (Control keypad: Menu M7) ............................................................ 38
6.5
Description of parameters ..................................................................................................... 39
6.5.1 Basic parameters ........................................................................................................... 39
6.5.2 Input signals ................................................................................................................... 42
6.5.3 Output signals................................................................................................................. 49
Tel. +358 (0)201 2121 • Fax +358 (0)201 212 205