Download Hyper-Utility Software Manual

Error message
Error message
Disk full. Conversion
interrupted.
Conversion could not
proceed because the hard
disk is full. Processing was
interrupted.
Solution
Remove some unwanted files from the
hard disk to create more space, or install
an additional hard disk.
Unsupported CCD
Raw file. Conversion
of this image
skipped.
This message appears when Skip conversion of this image.
you have attempted to
convert a file with a format
other than the CCD-RAW
(RAF) format shot on a
FinePix S2 Pro.
Processing could not
continue due to lack
of memory.
Conversion will end.
Conversion processing
cannot be performed as
there is insufficient memory
available to the application.
Processing was interrupted.
New type of CCD
Raw data. Current
settings are invalid,
please recheck.
This message appears when The settings used up to this point are no
you have attempted to
longer valid. Check the settings again.
convert a file with a format
other than the CCD-RAW
(RAF) format shot on a
FinePix S2 Pro.
Settings file
corrupted.
This message appears when This settings file cannot be used.
the imported settings file is
Specify the settings again.
damaged.
This CCD Raw file is
not supported by the
current settings.
Specify the settings
again.
This message appears when The settings used up to this point are no
you have attempted to
longer valid. Check the settings again.
convert a file with a format
other than the CCD-RAW
(RAF) format shot on a
FinePix S2 Pro.
Setting save failed.
The disk may be full or write- Check the remaining disk space, the file
protected, or you may be
properties and any other applications that
trying to overwrite another
are running.
settings file that is in use or
is write-protected.
Could not import the
settings file.
40
CAMERA SHOOTING SOFTWARE
Problem
There may be a disk error or
the settings file may be in
use by another application.
Shut down any other active applications or
install additional memory. On Macintosh
computers, increase the amount of
memory allocated to the application.
Test the disk and check any other
applications that are running.
Troubleshooting
Problem
Probable Cause
Solution
“FEE” is displayed
on the camera’s LCD
panel and I can’t take
pictures.
The aperture ring on the lens Set the aperture ring on the lens to the
is not set to the largest Flargest F-stop setting.
stop setting.
I mistakenly
disconnected the
cable when I was
using CAMERA
SHOOTING
SOFTWARE in
Windows Me and the
operating system has
reverted to a blue
screen.
Disconnection of the cable
during CAMERA SHOOTING
SOFTWARE operation is not
supported.
Follow the correct shutdown procedure as
directed by the messages on the blue
screen.
Because Windows operation is not stable
once the blue screen has appeared, you
should reboot the operating system.
If I switch the camera
off when I am using
CAMERA SHOOTING
SOFTWARE in
Windows Me, the
operating system
reverts to a blue
screen.
Switching the camera off
during CAMERA SHOOTING
SOFTWARE operation is not
supported.
Follow the correct shutdown procedure as
directed by the messages on the blue
screen.
Because Windows operation is not stable
once the blue screen has appeared, you
should reboot the operating system.
I mistakenly
disconnected the
cable when I was
using CAMERA
SHOOTING
SOFTWARE on Mac
OS and my
Macintosh can no
longer detect the
camera.
Disconnection of the cable
Restart your Macintosh.
during CAMERA SHOOTING
SOFTWARE operation is not
supported.
If I switch the camera
off when I am using
CAMERA SHOOTING
SOFTWARE on Mac
OS, my Macintosh
will not detect the
camera next time.
Switching the camera off
Restart your Macintosh.
during CAMERA SHOOTING
SOFTWARE operation is not
supported.
“Err” appears on the
camera and the
camera no longer
responds.
The camera batteries are
flat.
The aperture settings
displayed in Camera
Control (Normal)
mode do not match
the settings on the
LCD panel.
The values displayed for the For the precise aperture setting, use the
aperture setting in CAMERA value displayed on the camera's LCD
SHOOTING SOFTWARE
panel.
are as follows: 1.0, 1.2, 1.4,
1.7, 2.0, 2.4, 2.8, 3.3, 4.0,
4.8, 5.6, 6.7, 8.0, 9.5, 11, 13,
16, 19, 22, 27, 32, 38, 45,
54, 64, 76, 90.
Remove the camera batteries and use the
AC Power Adapter AC-5VH.
To use the built-in flash, you will need to
install fresh batteries.
41