Download Technical data

RFID
READER
13.56MHz Reader/Writer
SL500
User Manual
Version 2.6
Dec 2009
StrongLink
StrongLink
SL500
CONTENT
1. GENERAL INFORMATION ........................................................................................ 5
2. TYPES AND EXPLANATION.................................................................................... 6
3. CONNECTING TO PC................................................................................................ 6
3.1 SL500-RS232 ............................................................................................................................. 6
3.2 SL500-USB................................................................................................................................. 7
4. SDK ................................................................................................................................ 8
5. DEMO............................................................................................................................ 8
5.1 ONLINE...................................................................................................................................... 8
5.2 SHC1102 ..................................................................................................................................... 9
5.3 ULTRALIGHT ........................................................................................................................... 9
5.4 ULTRALIGHT C...................................................................................................................... 10
5.5 MIFARE_1K (STD S50) .......................................................................................................... 10
5.6 MIFARE_4K (STD S70) ...........................................................................................................11
5.7 MIFARE_PROX ........................................................................................................................11
5.8 TRH1064................................................................................................................................... 12
5.10 SRIX4K................................................................................................................................... 13
5.11 AT88RF020............................................................................................................................. 13
5.12 ISO14443B-4 PROTOCOL SMART CARD.......................................................................... 14
5.13 I.CODE SLI............................................................................................................................. 14
5.14 TAG_IT................................................................................................................................... 15
5.15 SRF55V02P............................................................................................................................. 15
5.16 SRF55V10P............................................................................................................................. 16
5.17 PASS_THROUGH.................................................................................................................. 16
6. DLL INFORMATION.................................................................................................. 17
6.1 SYSTEM FUNCTION ............................................................................................................ 17
6.1.1 INT WINAPI LIB_VER ........................................................................................................ 17
6.1.2 INT WINAPI RF_INIT_COM ............................................................................................... 17
6.1.3 INT WINAPI RF_CLOSEPORT ........................................................................................... 17
6.1.4 INT WINAPI RF_GET_MODEL .......................................................................................... 17
6.1.5 INT WINAPI RF_INIT_DEVICE_NUMBER ...................................................................... 17
6.1.7 INT WINAPI RF_INIT_TYPE .............................................................................................. 18
6.1.8 INT WINAPI RF_ANTENNA_STA...................................................................................... 18
6.1.9 INT WINAPI RF_LIGHT ...................................................................................................... 18
6.1.10 INT WINAPI RF_BEEP ...................................................................................................... 18
6.2 DES FUNCTION..................................................................................................................... 19
6.2.1 INT WINAPI DES_ENCRYPT ............................................................................................. 19
http://www.stronglink.cn
2
StrongLink
SL500
6.2.2 INT WINAPI DES_DECRYPT ............................................................................................. 19
6.3 ISO14443A FUNCTION........................................................................................................... 19
6.3.1 UltraLight............................................................................................................................... 19
6.3.1.1 INT WINAPI RF_REQUEST ............................................................................................. 19
6.3.1.2 INT WINAPI RF_UL_SELECT ......................................................................................... 20
6.3.1.3 INT WINAPI RF_M1_READ............................................................................................. 20
6.3.1.4 INT WINAPI RF_UL_WRITE ........................................................................................... 20
6.3.1.5 INT WINAPI INT RF_UC_AUTHENTICATION ............................................................. 20
6.3.1.6 INT WINAPI RF_UC_CHANGEKEY............................................................................... 21
6.3.1.7 INT WINAPI RF_HALT..................................................................................................... 21
6.3.2 Mifare Class .......................................................................................................................... 22
6.3.2.1 INT WINAPI RF_REQUEST ............................................................................................. 22
6.3.2.2 INT WINAPI RF_ANTICOLL ........................................................................................... 22
6.3.2.3 INT WINAPI RF_SELECT ................................................................................................ 22
6.3.2.4 INT WINAPI RF_M1_AUTHENTICATION2................................................................... 23
6.3.2.5 INT WINAPI RF_M1_READ............................................................................................. 23
6.3.2.6 INT WINAPI RF_M1_WRITE........................................................................................... 23
6.3.2.7 INT WINAPI RF_M1_INITVAL........................................................................................ 23
6.3.2.8 INT WINAPI RF_M1_READVAL ..................................................................................... 24
6.3.2.9 INT WINAPI RF_M1_INCREMENT ................................................................................ 24
6.3.2.10 INT WINAPI RF_M1_DECREMENT ............................................................................. 24
6.3.2.11 INT WINAPI RF_M1_RESTORE .................................................................................... 24
6.3.2.12 INT WINAPI RF_M1_TRANSFER ................................................................................. 24
6.3.2.13 INT WINAPI RF_HALT................................................................................................... 25
6.3.3 Mifare_DESFire ................................................................................................................... 25
6.3.3.1 INT WINAPI RF_DESFIRE_RST...................................................................................... 25
6.3.3.2 INT WINAPI RF_COS_COMMAND ................................................................................ 25
6.3.4 Mifare_ProX ......................................................................................................................... 26
6.3.4.1 INT WINAPI RF_TYPE_RST............................................................................................ 26
6.3.4.2 INT WINAPI RF_ COS_COMMAND ............................................................................... 26
6.3.4.3 INT WINAPI RF_CL_DESELECT .................................................................................... 26
6.3.5 SHC1102 ................................................................................................................................ 26
6.3.5.1 INT WINAPI RF_REQUEST ............................................................................................. 26
6.3.5.2 INT WINAPI RF_ SHC1102_AUTH ................................................................................. 27
6.3.5.3 INT WINAPI RF_ SHC1102_READ.................................................................................. 27
6.3.5.4 INT WINAPI RF_ SHC1102_WRITE................................................................................ 27
6.4 ISO14443B FUNCTION ......................................................................................................... 28
6.4.1 THR1064 ............................................................................................................................... 28
6.4.1.1 INT WINAPI RF_TYPEB_RST ......................................................................................... 28
6.4.1.2 INT WINAPI RF_ THR1064_READ ................................................................................. 28
6.4.1.3 INT WINAPI RF_ THR1064_WRITE................................................................................ 28
6.4.1.4 INT WINAPI RF_ THR1064_CHECK............................................................................... 28
6.4.2 AT88RF020 ........................................................................................................................... 29
6.4.2.1 INT WINAPI RF_ TYPEB_RST ........................................................................................ 29
http://www.stronglink.cn
3
StrongLink
SL500
6.4.2.2 INT WINAPI RF_ AT020_CHECK.................................................................................... 29
6.4.2.3 INT WINAPI RF_ AT020_COUNT.................................................................................... 29
6.4.2.4 INT WINAPI RF_ AT020_READ....................................................................................... 29
6.4.2.5 INT WINAPI RF_ AT020_WRITE..................................................................................... 30
6.4.2.6 INT WINAPI RF_ AT020_LOCK....................................................................................... 30
6.4.2.7 INT WINAPI RF_ AT020_DESELECT ............................................................................. 30
6.4.3 SR176SRIX4K ...................................................................................................................... 30
6.4.3.1 INT WINAPI RF_ST_SELECT.......................................................................................... 30
6.4.3.2 INT WINAPI INT_RF_SR176_READBLOCK ................................................................. 30
6.4.3.3 INT WINAPI INT_RF_SR176_WRITEBLOCK ............................................................... 31
6.4.3.4 INT WINAPI INT_RF_SR176_PROTECTBLOCK .......................................................... 31
6.4.3.5 INT WINAPI INT_RF_SRIX4K_ GETUID....................................................................... 31
6.4.3.6 INT WINAPI INT_RF_SRIX4K_ READBLOCK ............................................................. 31
6.4.3.7 INT WINAPI INT_RF_SRIX4K_ WRITEBLOCK ........................................................... 32
6.4.3.8 INT WINAPI INT_RF_SRIX4K_ PROTECTBLOCK ...................................................... 32
6.4.3.9 INT WINAPI RF_ST_COMPLETION............................................................................... 32
6.4.4 TYPE_B SmartCard ............................................................................................................ 33
6.4.4.1 INT WINAPI RF_ TYPEB_RST ........................................................................................ 33
6.4.4.2 INT WINAPI RF_ COS_COMMAND ............................................................................... 33
6.4.4.3 INT WINAPI RF_ CL_DESELECT ................................................................................... 33
6.5 ISO15693 FUNCTION............................................................................................................ 34
6.5.1 INT WINAPI ISO15693_INVENTORY................................................................................ 34
6.5.2 INT WINAPI ISO15693_INVENTORYS ............................................................................. 34
6.5.3 INT WINAPI ISO15693_GET_SYSTEM_INFORMATION................................................ 34
6.5.4 INT WINAPI ISO15693_SELECT........................................................................................ 35
6.5.5 INT WINAPI ISO15693_RESET_TO_READY ................................................................... 35
6.5.6 INT WINAPI ISO15693_STAY_QUIET............................................................................... 35
6.5.7 INT WINAPI ISO15693_GET_BLOCK_SECURITY.......................................................... 35
6.5.8 INT WINAPI ISO15693_READ............................................................................................ 36
6.5.9 INT WINAPI ISO15693_WRITE.......................................................................................... 36
6.5.10 INT WINAPI ISO15693_LOCK_BLOCK .......................................................................... 37
6.5.11 INT WINAPI ISO15693_WRITE_AFI................................................................................ 37
6.5.12 INT WINAPI ISO15693_LOCK_AFI ................................................................................. 37
6.5.13 INT WINAPI ISO15693_WRITE_DSFID .......................................................................... 38
6.5.14 INT WINAPI ISO15693_LOCK_DSFID ............................................................................ 38
6.6 FUNCTION OF INFINEON ELECTRIC TAG ................................................................... 39
6.6.1 INT WINAPI SRF55VP_READ............................................................................................ 39
6.6.2 INT WINAPI SRF55VP_WRITEBYTE................................................................................ 39
6.6.3 INT WINAPI SRF55VP_WRITE .......................................................................................... 39
6.6.4 INT WINAPI SRF55VP_WRITE_REREAD ........................................................................ 40
6.7 PASS THROUGH FUNCTION ............................................................................................. 40
6.7.1 INT WIN API RF_TRANSCEIVE1 ...................................................................................... 40
http://www.stronglink.cn
4
StrongLink
SL500
1. GENERAL INFORMATION
•
RS232 or USB Interface
•
4.5 ~ 5.5VDC Operating
•
Windows 32 Operating Systems Compatibility
•
13.56MHz RF Operating Frequency
•
ISO14443A ISO1443B ISO15693 Protocols
•
150MA Working Current
•
Operating Temperature Range:
•
Storage Temperature Range: -25°C ~ +60°C
•
Dimension: 110 × 81 × 26 mm
•
Weight: 100g
http://www.stronglink.cn
5
-20°C ~ +50°C
StrongLink
SL500
2. TYPES AND EXPLANATION
SL500 series readers are in accord with ISO14443A, ISO14443B and ISO15693
protocols, and are classified as following sheet
SL500L
SL500A
SL500D
SL500F
√
√
√
ISO14443A
√
ISO14443B
√
√
ISO15693
NOTICE: The difference between SL500L and SL500A
SL500L supported cards: Mifare_1k, Mifare_4k, UltraLight
SL500A supported cards: Mifare_1k, Mifare_4k, UltraLight, Mifare_ProX
3. CONNECTING TO PC
3.1 SL500-RS232
The PS/2 port power to Reader
http://www.stronglink.cn
6
StrongLink
SL500
3.2 SL500-USB
SL500-USB Reader is USB bridge to COM. Connect SL500 to the USB port of PC, after
installing the driver will come out a virtual COM, the operations hereafter are as same as
SL500-RS232.
You can find the virtual COM number on the “Device Manager ” as follows:
http://www.stronglink.cn
7
StrongLink
SL500
4. SDK
Responding InstDemo.exe to install the DEMO software and the DLL of the reader
to PC, and create corresponding logo on the desk.
The default installation directory is C:\RFREADER, including the following content:
C:\RFREADER\Examples
Sample source code
C:\RFREADER\UsbDriver
USB interface driver
C:\RFREADER\ICTransfer.exe DEMO software
C:\RFREADER\MasterRD.dll
Reader interface library with application
C:\RFREADER\MasterCOM.dll Connect and transfer data with COM device.
C:\RFREADER\SL_Paper.dll
DEMO software background library
C:\RFREADER\RFHELP.chm
DLL explanations at chm format
C:\RFREADER\AppConfig.ini
DEMO software configuration files
5. DEMO
This software run on Win32 system, and need 1024 x 768 dpi at least
5.1 Online
Choose the correct COM number, click [Connect] button to connect the Reader to
PC. Click [Read] the product information button, you can check the specific type of
the Reader and the supported cards.
http://www.stronglink.cn
8
StrongLink
SL500
5.2 SHC1102
Click [Request] button to obtain the card serial number.
Input the correct key to read/write the card
.
5.3 UltraLight
Click the [Request] button to obtain the card Serial Number.
Choose the corresponding address to read/write the card.
http://www.stronglink.cn
9
StrongLink
SL500
5.4 UltraLight C
Click the [Request] button to obtain the card Serial Number.
Choose the corresponding address to read/write the card
5.5 Mifare_1k (STD S50)
Click the [Request] button to obtain the card serial number.
Input the correct password to read, write, increase or decrease the card.
http://www.stronglink.cn
10
StrongLink
SL500
5.6 Mifare_4k (STD S70)
Click the [Request] button to obtain the card serial number.
Input the correct password to read, write, increase or decrease the card.
5.7 Mifare_ProX
Click [Reset] button to obtain the serial number and the reset information of the
card according to ISO14443-4 protocol.
Input the COS command, click [Send] button to commute data to card.
http://www.stronglink.cn
11
StrongLink
SL500
5.8 TRH1064
Click [Request] button to obtain the card serial number.
Hereafter can read, write and validate.
5.9 SR176
Click [Req] button to obtain the ID number of the card.
Then you can read, write and lock blocks of the card.
http://www.stronglink.cn
12
StrongLink
SL500
5.10 SRIX4K
Click [Req] button to obtain the ID number of the card and click [Read UID]
to obtain the UID of the card.
Then you can read, write and lock blocks of the card.
5.11 AT88RF020
Click [ReqB] button to obtain the serial number of the card.
After check password, you can read, write, signature and lock blocks of the
card.
http://www.stronglink.cn
13
StrongLink
SL500
5.12 ISO14443B-4 Protocol Smart Card
Click [Reset] button to obtain the serial number and the reset information of the
card according to ISO14443-4 protocol.
Input the COS command, click [Send] button to commute data to card.
5.13 I.CODE SLI
Click [INVENTORY] button to obtain the serial number of the card. You can
operate 4 cards at most.
Choose certain card according to the UID to read or write.
http://www.stronglink.cn
14
StrongLink
SL500
5.14 Tag_IT
Click [INVENTORY] button to obtain the serial number of the card. You can
operate 4 cards at most.
Choose certain card according to the UID to read/write.
5.15 SRF55V02P
Click [INVENTORY] button to obtain the serial number of the card. You can
operate 4 cards at most.
Choose certain card according to the UID to read/write.
http://www.stronglink.cn
15
StrongLink
SL500
5.16 SRF55V10P
Click [INVENTORY] button to obtain the serial number of the card. You can
operate 4 cards at most.
Choose certain card according to the UID to read/write.
5.17 Pass_Through
In this windows, input parameters according to ISO14443B and ISO15693
protocol, click [Transceive] button to get response data from tag
CRC bytes is auto managed by reader, it will not be contained in the stream
http://www.stronglink.cn
16
StrongLink
SL500
6. DLL INFORMATION
All types of readers have system function and encrypt function.
Whether readers support other functions depends on their specific types.
6.1 SYSTEM FUNCTION
6.1.1 INT WINAPI LIB_VER
Function:
Prototype:
Parameter:
Return:
Get DLL Version
int WINAPI lib_ver (unsigned int *pVer)
pVer:
[OUT]
DLL version
return 0 if successful
6.1.2 INT WINAPI RF_INIT_COM
Function: Connect
Prototype: int WINAPI rf_init_com (int port, long baud)
Parameter: port:
[IN]
serial port number
baud:
[IN]
communication baud rate, 4800 ~ 115200 bps
Return 0 on success
6.1.3 INT WINAPI RF_CLOSEPORT
Function: Disconnect
Prototyp: int WINAPI rf_ClosePort(void)
Return 0 on success
6.1.4 INT WINAPI RF_GET_MODEL
Function: Get Device Type
Prototype: int WINAPI rf_get_model (unsigned short icdev,
unsigned char *pVersion,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
pVersion:
pLen:
Return 0 on success
[OUT]
[OUT]
response information
length of response information
6.1.5 INT WINAPI RF_INIT_DEVICE_NUMBER
Function: Designate Device ID
Prototype: int WINAPI rf_init_device_number (unsigned short icdev)
Parameter: icdev:
[IN]
Device ID
Return 0 on success
http://www.stronglink.cn
17
StrongLink
SL500
6.1.6 INT WINAPI RF_GET_DEVICE_NUMBER
Function: Read Device ID
Prototype: int WINAPI rf_get_device_number (unsigned short *pIcdev)
Parameter: pIcdev:
Return 0 on success
[OUT]
response Device ID
6.1.7 INT WINAPI RF_INIT_TYPE
Function: Set Reader contactless working mode
Prototype: int WINAPI rf_init_type(unsigned short icdev, unsigned char type)
Parameter: icdev:
[IN]
Device ID
type:
[IN]
reader working mode
Return 0 on success
Explanation: this function is not effective to the readers only support single protocol.
type = 'A': set SL500 into ISO14443A mode
type = 'B': set ISO14443B mode
type = 'r': set AT88RF020 card mode
type = '1': set ISO15693 mode
6.1.8 INT WINAPI RF_ANTENNA_STA
Function: Manage RF Transmittal
Prototype: int WINAPI rf_antenna_sta (unsigned short icdev, unsigned char model)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
transmittal state
Return 0 on success
Explanation:model = 0: turn off RF transmittal
model = 1: turn on RF transmittal
6.1.9 INT WINAPI RF_LIGHT
Function: Manage LED
Prototype: int WINAPI rf_light (unsigned short icdev, unsigned char color)
Parameter: icdev:
[IN]
Device ID
color:
[IN]
0 = off
1 = red
2 = green
3 = yellow
Return 0 on success
6.1.10 INT WINAPI RF_BEEP
Function: beep
Prototype: int WINAPI rf_beep (unsigned short icdev, unsigned char msec)
Parameter: icdev:
[IN]
Device ID
msec:
[IN]
beep time, unit 10 MSEL
Return 0 on success
http://www.stronglink.cn
18
StrongLink
SL500
6.2 DES FUNCTION
6.2.1 INT WINAPI DES_ENCRYPT
Function: DES_Encrypt
Prototype: int WINAPI des_encrypt ( unsigned char *pSzOut,
unsigned char *pSzIn,
unsigned int
inlen,
unsigned char *pKey,
unsigned int
keylen)
Parameter: pSzOut:
[OUT]
ciphertext, bytes length equal to plaintext
pSzIn:
[IN]
plaintext
inlen:
[IN]
length of plaintext, integer times of 8 bytes
pKey:
[IN]
encrypt key
keylen:
[IN]
length of key, 8 bytes for single DES, 16 bytes for triple DES
Return 0 on success
6.2.2 INT WINAPI DES_DECRYPT
Function: DES_Decrypt
Prototype: int WINAPI des_decrypt ( unsigned char *pSzOut,
unsigned char *pSzIn,
unsigned int
inlen,
unsigned char *pKey,
unsigned int
keylen)
Parameter: pSzOut:
[OUT]
plaintext, bytes length equal to ciphertext
pSzIn:
[IN]
ciphertext
inlen:
[IN]
length of ciphertext, integer times of 8 bytes
pKey:
[IN]
encrypt key
keylen:
[IN]
length of key, 8 bytes for single DES, 16 bytes for triple DES
Return 0 on success
6.3 ISO14443A FUNCTION
6.3.1 UltraLight
6.3.1.1 INT WINAPI RF_REQUEST
Function: ReqA
Prototype: int WINAPI rf_request ( unsigned short icdev,
unsigned char model,
unsigned short *pTagType)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
REQ MODE
pTagType: [OUT]
response data, chip type code
Return 0 on success
Annotation: mode = 0x26: REQ_STD
mode = 0x52: REQ_ALL
http://www.stronglink.cn
19
StrongLink
SL500
6.3.1.2 INT WINAPI RF_UL_SELECT
Function: Select UltraLight
Prototype: int WINAPI int rf_ul_select (unsigned short icdev,
unsigned char *pSnr,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
pSnr:
[OUT]
response data, card unique serial number
pLen:
[OUT]
length of response data
Return 0 on success
6.3.1.3 INT WINAPI RF_M1_READ
Function: MifareOne read
Prototype: int WINAPI rf_M1_read ( unsigned short icdev,
unsigned char
block,
unsigned char *pData,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
block:
[IN]
block absolute address
pData:
[OUT]
response data from card
pLen:
[OUT]
length of response data
Return 0 on success
Annotation: this function is also applicable for UltraLight card. Every page of UltraLight card has 4
bytes. After calling this function, return data of 4 consecutive pages.
6.3.1.4 INT WINAPI RF_UL_WRITE
Function: UltraLight Write
Prototype: int WINAPI int rf_ul_write ( unsigned short icdev,
unsigned char
page,
unsigned char *pData)
Parameter: icdev:
[IN]
Device ID
page:
[IN]
UltraLight card page address , 0 ~ 0x0F
pData:
[IN]
written data, 4 bytes
Return 0 on success
6.3.1.5 INT WINAPI INT RF_UC_AUTHENTICATION
Function: Authenticate Key for Ultralight C
Prototype: int WINAPI rf_UC_authentication(unsigned short icdev,
unsigned char *pKey))
Parameter: icdev:
pKey:
Return 0 on success
[IN]
[IN]
http://www.stronglink.cn
Communication device identifier
Key, 16 bytes
20
StrongLink
SL500
6.3.1.6 INT WINAPI RF_UC_CHANGEKEY
Function: Update key of Ultralight C
Prototype: int WINAPI rf_UC_changekey(unsigned short icdev, unsigned char *pKey)
Parameter: icdev:
[IN]
Communication device identifier
pKey:
[IN]
Key, 16 bytes
Return 0 on success
6.3.1.7 INT WINAPI RF_HALT
Function: TYPE_A card HALT
Prototype: int WINAPI rf_halt (unsigned short icdev)
Parameter: icdev: [IN]
Communication device identifier
Return 0 on success
http://www.stronglink.cn
21
StrongLink
SL500
6.3.2 Mifare Class
6.3.2.1 INT WINAPI RF_REQUEST
Function: ReqA
Prototype: int WINAPI rf_request ( unsigned short icdev,
unsigned char
model,
unsigned short *pTagType)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
REQ MODE
pTagType: [OUT]
response data, chip type code
Return 0 on success
Annotation: mode = 0x26: REQ_STD
mode = 0x52: REQ_ALL
6.3.2.2 INT WINAPI RF_ANTICOLL
Function: Mifare card Anticollision
Prototype: int WINAPI rf_anticoll ( unsigned short icdev,
unsigned char
bcnt,
unsigned char *pSnr,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
bcnt:
[IN]
must be 4
pSnr:
[OUT]
response data from card, unique serial number
pLen:
[OUT]
length of response data
Return:
return 0 if successful
6.3.2.3 INT WINAPI RF_SELECT
Function: Mifare card Selectting
Prototype: int WINAPI rf_select (unsigned short icdev,
unsigned char *pSnr,
unsigned char snrLen,
unsigned char *pSize)
Parameter: icdev:
[IN]
Device ID
pSnr:
[IN]
card unique serial number
snrLen:
[IN]
length of pSnr
pSize:
[OUT]
response data from card, capacity code
Return 0 on success
Annotation: card will be on active estate after received this command, only one TYPE_A card on
active estate at the same influence range at same time.
http://www.stronglink.cn
22
StrongLink
SL500
6.3.2.4 INT WINAPI RF_M1_AUTHENTICATION2
Function: Mifare_Std Authentify
Prototype: int WINAPI rf_M1_authentication2 ( unsigned short icdev,
unsigned char model,
unsigned char block,
unsigned char *pKey)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
key validate mode
block:
[IN]
block absolute address
pKey:
[IN]
6 bytes password
Return 0 on success
Annotation: model = 0x60: use KeyA
model = 0x61: use KeyB
6.3.2.5 INT WINAPI RF_M1_READ
Function: MifareOne Read
Prototype: int WINAPI rf_M1_read ( unsigned short
unsigned char
unsigned char
unsigned char
Parameter: icdev:
[IN]
Device ID
block:
[IN]
block absolute address
pData:
[OUT] response data from card
pLen:
[OUT] length of response data
Return 0 on success
icdev,
block,
*pData,
*pLen)
6.3.2.6 INT WINAPI RF_M1_WRITE
Function: Mifare_Std Write
Prototype: int WINAPI rf_M1_write (unsigned short icdev,
unsigned char block,
unsigned char *pData)
Parameter: icdev:
[IN]
Device ID
block:
[IN]
block absolute address
pData:
[IN]
written data, 16 bytes
Return 0 on success
6.3.2.7 INT WINAPI RF_M1_INITVAL
Function: Mifare_Std card Initialize Value
Prototype: int WINAPI rf_M1_initval ( unsigned short icdev,
unsigned char block,
long value)
Parameter: icdev: [IN]
Device ID
block: [IN]
block absolute address
pValue: [IN]
initialize purse value at HEX format, low byte in former
http://www.stronglink.cn
23
StrongLink
SL500
Return 0 on success
6.3.2.8 INT WINAPI RF_M1_READVAL
Function: Mifare_Std Read Value
Prototype: int WINAPI rf_M1_readval ( unsigned short icdev,
unsigned char block,
long *pValue)
Parameter: icdev: [IN]
Device ID
block: [IN]
block absolute address
pValue: [OUT]
response value at HEX format, low byte in former
Return 0 on success
6.3.2.9 INT WINAPI RF_M1_INCREMENT
Function: Mifare purse increment
Prototype: int WINAPI rf_M1_increment (unsigned short icdev,
unsigned char block,
long value)
Parameter: icdev:
[IN]
Device ID
block:
[IN]
block absolute address
value:
[IN]
increase value at HEX format, low byte in former
Return 0 on success
6.3.2.10 INT WINAPI RF_M1_DECREMENT
Function: Mifare purse decrement
Prototype: int WINAPI rf_M1_decrement (unsigned short icdev,
unsigned char block,
long value)
Parameter: icdev: [IN]
Device ID
block: [IN]
block absolute address
value: [IN]
decrease value at HEX format, low byte in former
Return 0 on success
6.3.2.11 INT WINAPI RF_M1_RESTORE
Function: Mifare_Std Restore
Prototype: int WINAPI rf_M1_restore (unsigned short icdev, unsigned char block)
Parameter: icdev:
[IN]
Device ID
block:
[IN]
block absolute address
Return 0 on success
6.3.2.12 INT WINAPI RF_M1_TRANSFER
Function: Mifare_Std Transfer
Prototype: int WINAPI rf_M1_transfer (unsigned short icdev, unsigned char block)
Parameter: icdev:
[IN]
Device ID
block:
[IN]
block absolute address
http://www.stronglink.cn
24
StrongLink
SL500
Return 0 on success
Annotation: this function only be transferred after increment, decrement and restore command
6.3.2.13 INT WINAPI RF_HALT
Function: Mifare Halt
Prototype: int WINAPI rf_halt (unsigned short icdev)
Parameter: icdev:
[IN]
Device ID
Return 0 on success
Annotation: card will exit active estate after received this command
6.3.3 Mifare_DESFire
6.3.3.1 INT WINAPI RF_DESFIRE_RST
Function: DESFire Reset
Prototype: int WINAPI rf_DESFire_rst ( unsigned short icdev,
unsigned char model,
unsigned char *pData,
unsigned char *pMsgLg)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
ReqA mode
pData: [OUT]
response data from card
pMsgLg: [OUT]
length of response data
Return 0 on success
Annotation: mode = 0x26: REQ_STD
mode = 0x52: REQ_ALL
pData = 7 bytes CSN + n bytes RATS according to ISO14443-4 protocol
6.3.3.2 INT WINAPI RF_COS_COMMAND
Function: DESFire data commutting
Prototype: int WINAPI rf_cos_command ( unsigned short icdev,
unsigned char *pCommand,
unsigned char cmdLen,
unsigned char *pData,
unsigned char *pMsgLg)
Parameter: icdev:
[IN]
Device ID
pCommand: [IN]
COS command
cmdLen:
[IN]
length of COS command
pData:
[OUT] response data from card
pMsgLg:
[OUT] length of response data
Return 0 on success
http://www.stronglink.cn
25
StrongLink
SL500
6.3.4 Mifare_ProX
6.3.4.1 INT WINAPI RF_TYPE_RST
Function: Request ISO14443A-4 card and reset
Prototype: int WINAPI rf_typea_rst ( unsigned short icdev,
unsigned char model,
unsigned char *pData,
unsigned char *pMsgLg)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
request mode
pData:
[OUT] response data from card
pMsgLg:
[OUT] length of response data
Return 0 on success
Annotation: mode = 0x26: REQ_STD
mode = 0x52: REQ_ALL
pData: 4bytes CSN + RATS according to ISO14443A
6.3.4.2 INT WINAPI RF_ COS_COMMAND
Prototype: int WINAPI rf_cos_command ( unsigned short icdev,
unsigned char *pCommand,
unsigned char cmdLen,
unsigned char *pData,
unsigned char *pMsgLg)
Parameter: icdev:
[IN]
Device ID
pCommand: [IN]
COS command
cmdLen:
[IN]
length of COS command
pData:
[OUT] response data from card, including SW1& SW2
pMsgLg:
[OUT] length of response data
Return 0 on success
6.3.4.3 INT WINAPI RF_CL_DESELECT
Prototype: int WINAPI rf_cl_deselect (unsigned short icdev)
Parameter: icdev:
[IN]
Device ID
Return 0 on success
6.3.5 SHC1102
6.3.5.1 INT WINAPI RF_REQUEST
Function: ReqA
Prototype: int WINAPI rf_request ( unsigned short icdev,
unsigned char model,
unsigned short *pTagType)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
REQ MODE
pTagType: [OUT]
response data from card, chip type code
Return 0 on success
http://www.stronglink.cn
26
StrongLink
SL500
Annotation: mode = 0x26: REQ_STD
mode = 0x52: REQ_ALL
6.3.5.2 INT WINAPI RF_ SHC1102_AUTH
Function: SHC1102 card Authentify
Prototype: int WINAPI rf_Shc1102_Auth (unsigned short icdev, unsigned char *pPassword)
Parameter: icdev:
[IN]
Device ID
pPassword:
Return 0 on success
[IN]
4 bytes password
6.3.5.3 INT WINAPI RF_ SHC1102_READ
Function: SHC1102 card read
Prototype: int WINAPI rf_Shc1102_Read (unsigned short icdev,
unsigned char block,
unsigned char *pData,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
block:
[IN]
SHC1102 card block address, 0x00 ~ 0x0F
pData:
[OUT] response data from card
pLen:
[OUT] length of response data
Return 0 on success
6.3.5.4 INT WINAPI RF_ SHC1102_WRITE
Function: SHC1102 card write
Prototype: int WINAPI rf_Shc1102_Write (unsigned short icdev,
unsigned char block,
unsigned char *pData)
Parameter: icdev:
[IN]
Device ID
block:
[IN]
SHC1102 card block address, 0x00 ~ 0x0F
pData:
[IN]
written data, 16 bytes
Return 0 on success
http://www.stronglink.cn
27
StrongLink
SL500
6.4 ISO14443B FUNCTION
6.4.1 THR1064
6.4.1.1 INT WINAPI RF_TYPEB_RST
Function: REQ THR1064 card
Prototype: int WINAPI rf_atqb (unsigned short icdev,
unsigned char model,
unsigned char *pData,
unsigned char *pMsgLg)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
REQ MODE 0=REQB, 1=WUPB
pData:
[OUT]
response data from card, 8 bytes SN + 4 bytes corresponding data
pMsgLg: [OUT]
length of response data
Return 0 on success
6.4.1.2 INT WINAPI RF_ THR1064_READ
Function: THR1064 card read
Prototype: int WINAPI rf_thr1064_read(unsigned short icdev,
unsigned char page,
unsigned char *pData,
unsigned char *pMsgLen)
Parameter: icdev:
[IN]
Device ID
page:
[IN]
page address, 0 ~3
pData:
[OUT]
response data from card
pMsgLen: [OUT]
length of response data
Return 0 on success
6.4.1.3 INT WINAPI RF_ THR1064_WRITE
Function: THR1064 card write
Prototype: int WINAPI rf_thr1064_write (unsigned short icdev,
unsigned char page,
unsigned char *pData,
unsigned char *pMsgLen);
Parameter: icdev:
[IN]
Device ID
page:
[IN]
page address, 0 ~3
pData:
[IN]
written data
pMsgLen: [OUT]
length of written data
Return 0 on success
6.4.1.4 INT WINAPI RF_ THR1064_CHECK
Function: THR1064 card Authentify
Prototype: int WINAPI rf_thr1064_check (unsigned short icdev, unsigned char *pKey)
Parameter: icdev:
[IN]
Device ID
http://www.stronglink.cn
28
StrongLink
pKey:
Return 0 on success
SL500
[IN]
8 bytes pass word
6.4.2 AT88RF020
6.4.2.1 INT WINAPI RF_ TYPEB_RST
Function: REQ ISO14443B protocol card and set SLOT
Prototype: int WINAPI rf_atqb(unsigned short icdev,
unsigned char model,
unsigned char *pData,
unsigned char *pMsgLg)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
REQ MODE 0 = REQB, 1 = WUPB
pData:
[OUT]
response data from card
pMsgLg: [OUT]
length of response data
Return 0 on success
6.4.2.2 INT WINAPI RF_ AT020_CHECK
Function: AT88RF020 card Authentify
Prototype: int WINAPI rf_at020_check (unsigned short icdev, unsigned char *pKey)
Parameter: icdev:
[IN]
Device ID
pKey:
[IN]
8 bytes pass word
Return 0 on success
6.4.2.3 INT WINAPI RF_ AT020_COUNT
Function: AT88RF020 card count
Prototype: int WINAPI rf_at020_count(unsigned short icdev, unsigned char *pData)
Parameter: icdev:
[IN]
Device ID
pData:
[IN]
signature, 6 bytes
Return 0 on success
6.4.2.4 INT WINAPI RF_ AT020_READ
Function: AT88RF020 read
Prototype: int WINAPI rf_at020_read (unsigned short icdev,
unsigned char page,
unsigned char *pData,
unsigned char *pMsgLen)
Parameter: icdev:
[IN]
Device ID
page:
[IN]
page address, 0 ~ 31
pData:
[OUT]
response data from card
pMsgLen: [OUT]
length of response data
Return 0 on success
http://www.stronglink.cn
29
StrongLink
SL500
6.4.2.5 INT WINAPI RF_ AT020_WRITE
Function: AT88RF020 write
Prototype: int WINAPI rf_at020_write ( unsigned short icdev,
unsigned char page,
unsigned char *pData)
Parameter: icdev:
[IN]
Device ID
page:
[IN]
page address, 0 ~ 31
pData:
[IN]
written data, 8 bytes
Return 0 on success
6.4.2.6 INT WINAPI RF_ AT020_LOCK
Function: AT88RF020 LOCK
Prototype: int WINAPI rf_at020_lock (unsigned short icdev, unsigned char *pData)
Parameter: icdev:
[IN]
Device ID
pData:
[IN]
4 bytes data
Return 0 on success
6.4.2.7 INT WINAPI RF_ AT020_DESELECT
Function: AT88RF020 card Deselect
Prototype: int WINAPI rf_at020_deselect (unsigned short icdev)
Parameter: icdev:
[IN]
Device ID
Return 0 on success
6.4.3 SR176SRIX4K
6.4.3.1 INT WINAPI RF_ST_SELECT
Function: ST card (SR176/SRIX4K) Lock
Prototype: int WINAPI rf_st_select (unsigned short icdev, unsigned char *pChip_ID)
Parameter: icdev:
[IN]
Device ID
pChip_ID: [IN]
response data from card, 1 byte ID code
Return 0 on success
6.4.3.2 INT WINAPI INT_RF_SR176_READBLOCK
Function: SR176 Read
Prototype: int WINAPI int rf_sr176_readblock ( unsigned short icdev,
unsigned char block,
unsigned char *pData,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
block:
[IN]
block address
pData:
[OUT] response data from card
pLen:
[OUT] length of response data
Return 0 on success
http://www.stronglink.cn
30
StrongLink
SL500
6.4.3.3 INT WINAPI INT_RF_SR176_WRITEBLOCK
Function: SR176 Write
Prototype: int WINAPI int rf_sr176_writeblock (unsigned short icdev,
unsigned char block,
unsigned char *pData)
Parameter: icdev:
[IN]
Device ID
block:
[IN]
block address
pData:
[IN]
written data, 2 bytes
Return 0 on success
6.4.3.4 INT WINAPI INT_RF_SR176_PROTECTBLOCK
Function: SR176 Lock
Prototype: int WINAPI int rf_sr176_protectblock (unsigned short icdev, unsigned char lockreg)
Parameter: icdev:
[IN]
Device ID
lockreg:
[IN]
LOCKREG
Return 0 on success
Annotation: SR17 6has 16 blocks, every lockreg controls 2 blocks
lockreg
b7
b6
b5
b4
b3
b2
b1
b0
BLOCK
14 & 15
12 & 13
10 & 11
8&9
6&7
4&5
2&3
0&1
bit_setting
0:Write Enable
1:Block set as ROM
0:Write Enable
1:Block set as ROM
0:Write Enable
1:Block set as ROM
0:Write Enable
1:Block set as ROM
0:Write Enable
1:Block set as ROM
0:Write Enable
1:Block set as ROM
0:Write Enable
1:Block set as ROM
0:Write Enable
1:Block set as ROM
6.4.3.5 INT WINAPI INT_RF_SRIX4K_ GETUID
Function: SRIX4K Get UID
Prototype: int WINAPI int rf_srix4k_getuid ( unsigned short icdev,
unsigned char *pUid,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
pUid:
[OUT] response data from card, UID
pLen:
[OUT] length of response data
Return 0 on success
6.4.3.6 INT WINAPI INT_RF_SRIX4K_ READBLOCK
Function: SRIX4K Read
Prototype: int WINAPI int rf_srix4k_readblock (unsigned short icdev,
unsigned char block,
unsigned char *pData,
unsigned char *pLen)
http://www.stronglink.cn
31
StrongLink
Parameter: icdev:
block:
pData:
pLen:
Return 0 on success
SL500
[IN]
[IN]
[OUT]
[OUT]
Device ID
block address
response data from card
length of response data
6.4.3.7 INT WINAPI INT_RF_SRIX4K_ WRITEBLOCK
Function: SRIX4K Write
Prototype: int WINAPI int rf_srix4k_writeblock(unsigned short icdev,
unsigned char block,
unsigned char *pData)
Parameter: icdev:
[IN]
Device ID
block:
[IN]
block address
pData:
[IN]
written data, 4bytes
Return 0 on success
6.4.3.8 INT WINAPI INT_RF_SRIX4K_ PROTECTBLOCK
Function: SRIX4K Lock
Prototype: int WINAPI int rf_srix4k_protectblock(unsigned short icdev, unsigned char lockreg)
Parameter: icdev:
[IN]
Device ID
Lockreg: [IN]
LOCKREG
Return 0 on success
Annotation: 7~15 blocks of SRIX4K card can be written protect
lockreg
b7
b6
b5
b4
b3
b2
b1
b0
BLOCK
15
14
13
12
11
10
9
7&8
bit_setting
1:Write Enable
0:Block set as ROM
1:Write Enable
0:Block set as ROM
1:Write Enable
0:Block set as ROM
1:Write Enable
0:Block set as ROM
1:Write Enable
0:Block set as ROM
1:Write Enable
0:Block set as ROM
1:Write Enable
0:Block set as ROM
1:Write Enable
0:Block set as ROM
6.4.3.9 INT WINAPI RF_ST_COMPLETION
Function: ST Desactived
Prototype: int WINAPI rf_st_completion (unsigned short icdev)
Parameter: icdev:
[IN]
Device ID
Return 0 on success
http://www.stronglink.cn
32
StrongLink
SL500
6.4.4 TYPE_B SmartCard
6.4.4.1 INT WINAPI RF_ TYPEB_RST
Function: Req ISO14443B-4 protocol Smart card and Reset
Prototype: int WINAPI rf_atqb ( unsigned short icdev,
unsigned char model,
unsigned char *pData,
unsigned char *pMsgLg)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
REQ MODE 0 = REQB, 1 = WUPB
pData:
[OUT]
response data from card
pMsgLg:
[OUT]
length of response data
Return 0 on success
6.4.4.2 INT WINAPI RF_ COS_COMMAND
Prototype: int WINAPI rf_cos_command (unsigned short icdev,
unsigned char *pCommand,
unsigned char cmdLen,
unsigned char *pData,
unsigned char *pMsgLg)
Parameter: icdev:
[IN]
Device ID
pCommand: [IN]
cos command
cmdLen:
[IN]
length of cos comman
pData:
[OUT]
response data from card, including SW1, SW2
pMsgLg:
[OUT]
length of response data
Return 0 on success
6.4.4.3 INT WINAPI RF_ CL_DESELECT
Function: ISO14443B card Deselect
Prototype: int WINAPI rf_cl_deselect (unsigned short icdev)
Parameter: icdev:
[IN]
Device ID
Return 0 on success
http://www.stronglink.cn
33
StrongLink
SL500
6.5 ISO15693 FUNCTION
6.5.1 INT WINAPI ISO15693_INVENTORY
Function: ISO15693_Inventory (single card)
Prototype: int WINAPI ISO15693_Inventory ( unsigned short icdev,
unsigned char *pData,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
pData:
[OUT]
response data from tag, 1 byte DSFID + 8 bytes UID
pLen:
[OUT]
length of response data
Return 0 on success
6.5.2 INT WINAPI ISO15693_INVENTORYS
Function: ISO15693_Inventory (several cards)
Prototype: int WINAPI ISO15693_Inventorys (unsigned short icdev,
unsigned char *pData,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
pData:
[OUT]
response data from tag, every 9 bytes is a team, the structure of
every team is:
1byte DSFID + 8 bytes UID
pLen:
[OUT]
length of response data
Return 0 on success
6.5.3 INT WINAPI ISO15693_GET_SYSTEM_INFORMATION
Function: ISO15693_Get_System_Information
Prototype: int WINAPI ISO15693_Get_System_Information(unsigned short icdev,
unsigned char model,
unsigned char *pUID,
unsigned char *pData,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
bit0=Select_flag, bit1=Addres_flag, bit2=Option_flag
pUID:
[IN]
8 bytes UID
pData:
[OUT]
response data from tag
pLen:
[OUT]
length of response data
Return 0 on success
Annotation:
If set Select_flag, only the cards on Selected state respond this command
If set Address_flag, only the cards that the UID are congruous will respond
this command
Clear Option_flag = 0
http://www.stronglink.cn
34
StrongLink
SL500
6.5.4 INT WINAPI ISO15693_SELECT
Function: ISO15693_Select
Prototype: int WINAPI ISO15693_Select (unsigned short icdev, unsigned char *pUID)
Parameter: icdev:
[IN]
Device ID
pUID:
[IN]
8 bytes UID
Return 0 on success
6.5.5 INT WINAPI ISO15693_RESET_TO_READY
Function: ISO15693_Reset_To_Ready
Prototype: int WINAPI ISO15693_Reset_To_Ready (unsigned short icdev,
unsigned char model,
unsigned char *pUID)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
bit0=Select_flag, bit1=Addres_flag, bit2=Option_flag
pUID:
[IN]
8 bytes UID
Return 0 on success
Annotation:
If set Select_flag, only the cards on Selected state respond this command
If set Address_flag, only the cards that the UID are congruous will respond
this command
Clear Option_flag = 0
6.5.6 INT WINAPI ISO15693_STAY_QUIET
Function: ISO15693_Stay_Quiet
Prototype: int WINAPI ISO15693_Stay_Quiet (unsigned short icdev, unsigned char *pUID)
Parameter: icdev:
[IN]
Device ID
pUID:
[IN]
8 bytes UID
Return 0 on success
6.5.7 INT WINAPI ISO15693_GET_BLOCK_SECURITY
Function: ISO15693_Get_Block_Security
Prototype: int WINAPI ISO15693_Get_Block_Security ( unsigned short icdev,
unsigned char model,
unsigned char *pUID,
unsigned char block,
unsigned char number,
unsigned char *pData,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
bit0=Select_flag, bit1=Addres_flag, bit2=Option_flag
pUID:
[IN]
8 bytes UID
block:
[IN]
block address
number: [IN]
the number of block to be read, < 0x40
pData:
[OUT]
response data from tag
pLen:
[OUT]
length of response data
http://www.stronglink.cn
35
StrongLink
SL500
Return 0 on success
Annotation:
If set Select_flag, only the cards on Selected state respond this command
If set Address_flag, only the cards that the UID are congruous will respond
this command
Clear Option_flag = 0
6.5.8 INT WINAPI ISO15693_READ
Function: ISO15693_Read
Prototype: int WINAPI ISO15693_Read ( unsigned short icdev,
unsigned char model,
unsigned char *pUID,
unsigned char block,
unsigned char number,
unsigned char *pData,
unsigned char *pLen);
Parameter: icdev:
[IN]
Device ID
model:
[IN]
bit0=Select_flag, bit1=Addres_flag, bit2=Option_flag
pUID:
[IN]
8 bytes UID
block:
[IN]
block address
number: [IN]
the number of block to be read, < 0x40
pData:
[OUT]
response data from tag
pLen:
[OUT]
length of response data
Return 0 on success
Annotation:
If set Select_flag, only the cards on Selected state respond this command
If set Address_flag, only the cards that the UID are congruous will respond
this command
Clear Option_flag = 0
6.5.9 INT WINAPI ISO15693_WRITE
Function: ISO15693_Write
Prototype: int WINAPI ISO15693_Write ( unsigned short icdev,
unsigned char model,
unsigned char *pUID,
unsigned char block,
unsigned char *pData)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
bit0=Select_flag, bit1=Addres_flag, bit2=Option_flag
pUID:
[IN]
8 bytes UID
block:
[IN]
block address
pData:
[IN]
written data, 4 bytes
Return 0 on success
Explanation: If set Select_flag, only the cards on Selected state respond this command
If set Address_flag, only the cards that the UID are congruous will respond
this command
http://www.stronglink.cn
36
StrongLink
SL500
If write TI card, set Option_flag,
If write I.CODE SLI card, clear Option_flag
6.5.10 INT WINAPI ISO15693_LOCK_BLOCK
Function: ISO15693_Lock_Block
Prototype: int WINAPI ISO15693_Lock_Block (unsigned short icdev,
unsigned char model,
unsigned char *pUID,
unsigned char block)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
bit0=Select_flag, bit1=Addres_flag, bit2=Option_flag
pUID:
[IN]
8 bytes UID
block:
[IN]
block address
Return 0 on success
Annotation:
If set Select_flag, only the cards on Selected state respond this command
If set Address_flag, only the cards that the UID are congruous will respond
this command
If write TI card, set Option_flag,
If write I.CODE SLI card, clear Option_flag
6.5.11 INT WINAPI ISO15693_WRITE_AFI
Function: ISO15693_Write_AFI
Prototype: int WINAPI ISO15693_Write_AFI (unsigned short icdev,
unsigned char model,
unsigned char *pUID,
unsigned char AFI)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
bit0=Select_flag, bit1=Addres_flag, bit2=Option_flag
pUID:
[IN]
8 bytes UID
AFI:
[IN]
AFI to be written
Return 0 on success
Annotation:
If set Select_flag, only the cards on Selected state respond this command
If set Address_flag, only the cards that the UID are congruous will respond
this command
If write TI card, set Option_flag,
If write I.CODE SLI card, clear Option_flag
6.5.12 INT WINAPI ISO15693_LOCK_AFI
Function: ISO15693_Lock_AFI
Prototype: int WINAPI ISO15693_Lock_AFI ( unsigned short icdev,
unsigned char model,
unsigned char *pUID)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
bit0=Select_flag, bit1=Addres_flag, bit2=Option_flag
http://www.stronglink.cn
37
StrongLink
pUID:
Return 0 on success
Annotation:
SL500
[IN]
8 bytes UID
If set Select_flag, only the cards on Selected state respond this command
If set Address_flag, only the cards that the UID are congruous will respond
this command
If write TI card, set Option_flag,
If write I.CODE SLI card, clear Option_flag
6.5.13 INT WINAPI ISO15693_WRITE_DSFID
Function: ISO15693_Write_DSFID
Prototype: int WINAPI ISO15693_Write_DSFID (unsigned short icdev,
unsigned char model,
unsigned char *UID,
unsigned char DSFID)
Parameter: icdev:
[IN]
Device ID
model:
[IN]
bit0=Select_flag, bit1=Addres_flag, bit2=Option_flag
pUID:
[IN]
8 bytes UID
DSFID: [IN]
DSFID to be written
Return 0 on success
Annotation:
If set Select_flag, only the cards on Selected state respond this command
If set Address_flag, only the cards that the UID are congruous will respond
this command
If write TI card, set Option_flag,
If write I.CODE SLI card, clear Option_flag
6.5.14 INT WINAPI ISO15693_LOCK_DSFID
Function: ISO15693_Lock_DSFID
Prototype: int WINAPI ISO15693_Lock_DSFID (
Parameter: icdev:
model:
pUID:
Return 0 on success
Annotation:
[IN]
[IN]
[IN]
unsigned short icdev,
unsigned char model,
unsigned char *pUID)
Device ID
bit0=Select_flag, bit1=Addres_flag, bit2=Option_flag
8 bytes UID
If set Select_flag, only the cards on Selected state respond this command
If set Address_flag, only the cards that the UID are congruous will respond
this command
If write TI card, set Option_flag,
If write I.CODE SLI card, clear Option_flag
http://www.stronglink.cn
38
StrongLink
SL500
6.6 Function of Infineon Electric Tag
6.6.1 INT WINAPI SRF55VP_READ
Function: SRF55XXP Read a PAGE
Prototype: int WINAPI Srf55vp_Read ( unsigned short
unsigned char
unsigned char
unsigned char
unsigned char
Parameter: icdev:
[IN]
Device ID
pUID:
[IN]
8 bytes UID
page:
[IN]
address
pData:
[OUT]
response data from tag
pLen:
[OUT]
length of response data
Return 0 on success
icdev,
*pUID,
page,
*pData,
*pLen)
6.6.2 INT WINAPI SRF55VP_WRITEBYTE
Function: SRF55XXP Write 1BYTE
Prototype: int WINAPI Srf55vp_WriteByte ( unsigned short icdev,
unsigned char *pUID,
unsigned char page,
unsigned char byteaddr,
unsigned char data)
Parameter: icdev:
[IN]
Device ID
pUID:
[IN]
8 bytes UID
page:
[IN]
address
byteaddr: [IN]
write the bytes to excursion address of the PAGE, 0 ~ 8
data:
[IN]
written data
Return 0 on success
6.6.3 INT WINAPI SRF55VP_WRITE
Function: SRF55XXP Write a page
Prototype: int WINAPI Srf55vp_Write ( unsigned short icdev,
unsigned char *pUID,
unsigned char page,
unsigned char *pData)
Parameter: icdev:
[IN]
Device ID
pUID:
[IN]
8 bytes UID
page:
[IN]
address
pData:
[IN]
written data, 8 bytes
Return 0 on success
http://www.stronglink.cn
39
StrongLink
SL500
6.6.4 INT WINAPI SRF55VP_WRITE_REREAD
Function: SRF55XXP write PAGE and Return to the real data of this PAGE
Prototype: int WINAPI Srf55vp_Write_Reread(unsigned short
icdev,
unsigned char *pUID,
unsigned char page,
unsigned char *pWdata,
unsigned char *pRdata,
unsigned char *pLen)
Parameter: icdev:
[IN]
Device ID
pUID:
[IN]
8 bytes UID
page:
[IN]
address
pWdata: [IN]
written data, 8bytes
pWdata: [OUT]
response data from tag
pLen:
[OUT]
length of response data
Return 0 on success
6.7 PASS THROUGH FUNCTION
6.7.1 INT WIN API RF_TRANSCEIVE1
Function: Send parameteres to Tag and receive response data
Prototype: int WINAPI rf_transceive1(unsigned short icdev,
unsigned char *pTxData,
unsigned char sendLen,
unsigned char *pRxData,
unsigned char *pMsgLg)
Parameter: icdev:
[IN]
Communication device identifier
pTxData: [IN]
parameter sent to tag, without CRC bytes
CRC bytes is auto managed by reader
sendLen: [IN]
length of parameter
pRxData: [OUT]
response data from tag
pMsgLg: [OUT]
length of response data
Return 0 on success
http://www.stronglink.cn
40