Download Installation Manual
Transcript
Shenzhen Yitoa Intelligent Control Co.,Ltd. HID Xenon Kits Installation Manual Please read this manual before you install For Automotive and Motorcycle Shenzhen Yitoa Intelligent Control Co.,Ltd. Add:Longma Industry Estate, Shiyan Town, Bao’an District Shenzhen City, Guangdong Province, P.R.C 518108 Tel:+86(0755)29042402/29572066/29826561 Fax:+86(0755)27651174 Email:[email protected]/[email protected] Web:www.yitoa.com/hid Technical Parameter Working principle Xenon lamp replaces the filament of the light bulb with xenon gas by utilizing the gas discharge principle, an arc of light is created between two electrodes in a small capsule filled with a mixture of xenon gas and halide salts. When high voltage is applied, the gas is ignited to produce an arc of light. HID does not have filaments like standard halogen bulbs. Instead an arc of electricity ignites magnetic salts within the bulb to cause the glow. Due to this technology, HID bulbs last 10 times as long as halogen, there is no filament to break or burn out. HID also consumes less electricity than halogen. Halogen bulbs consume approximately 55 watts of electricity where HID only consumes about 35 watts. Xenon HID outputs three times the amount of light compared to a standard halogen bulb. The lamp glows at a higher light temperature and gives it its distinct color and appearance. Basic Fittings This package includes the parts as the following: 1. Automobile: 2pcs ballasts, 2pcs HID xenon lamps, 1pcs bunches of wires, 1pc warranty card, 2pcs tape, 2pcs brackets 7pcs accessories. 2. Motorcycle: 1pc ballast, 1pc HID xenon lamp, 1 bunch of wire, 1 warranty card, 1pc tape, 7pcs accessories. Wires Tape 01 www.yitoa.com/hid Bracket 1.Open the car bonnet, check the assembly space. If the space is enough, assemble the lamp directly. If the space is not enough, then remove the left & right halogen headlamps from the car, then assembly. 2.Drill a hole in the middle of the rear cover with a 21mm hole cutter. Xenon lamp Ballasts Installation Process Accessories 02 www.yitoa.com/hid 3.Take out the plastic cap of the HID bulb. (Don’t touch the bulb to avoid burn.) 7.Connect the lamp wire with ballast wire. 4 . I n s t a l l t h e H I D l a m p i n t h e c a r. M a k e s u r e t h e p r e s s s p r i n g h a s b e e n a s s e m b l e d p r o p e r l y. 5.Connect the wires. 6.Take the bulb wire. Fix the ballast with double faced adhesive tape firmly to the ventilatory place, keep some distance with motor. 8.Test the lamps and make sure they can work properly. Installation Notice 1.Recommend a professional technician to install the unit. 2.Make sure the engine and light are cool enough before installation to prevent a burn. 3.Wear gloves in the operation to avoid the electric shock. 4.Don't stare at the xenon light directly to protect your eyes. 03 www.yitoa.com/hid 04 www.yitoa.com/hid 5.Don' t keep the light in an upward direction to ensure the safety of the opposite drivers. 6.Any damage and problems caused by not following the process will not include in our free charge after-sale service. Trouble Shooting 1. Problem: Both left and right lamps don't work or flicker after installed the HID system. Solution: 1.1. Check the wires. Make sure the positive and negative terminal are connect correctly. 1.2. Automobile storage battery power is not enough. Change the battery with 60Ah plus current. If you don't want to change the storage battery, then add extra relays to bear 15Ah plus. Make sure the fuse is over 20Ah, otherwise it will be damaged easily. 2. Problem: For the cars that have Auto ""ON"" or Daytime Running Lights; one or both light can't ignite initially, bulb turns off once the car started, or bulb turns off upon driving. Solution: Disconnect the Daytime Running Light or Auto Switch ON function immediately. The automobile storage battery requires the stable voltage is about 12V plus before igniting. Don't allow to start the HID system with low voltage. Daytime Running Light is about 7V or lower power output, and auto switch function is always turn on the headlamp a few second before igniting, which means battery is focus on ignition and waiting for alternate back to 12V. Therefore, in both situations, battery has much less power than 12V to ignite the HID headlight initially. Please take action as the following: 2.1 Disconnect the fuse or wiring of Daytime Running lights based on the user manual of the car. 2.2 Switch off the auto “on” function based on the user manual of the car. To avoid further damage, always start the engine before turn on the HID system. 4. Problem: HID turns on, but both lamps go out. Solution: The fuses are blown. Check your fuses box based on the user manual of the car and change the headlight fuse to 30A. 5. Problem: HID system switches off automatically sometimes. Solution: There is a chip in HID ballast which is used to detect potential problem. It will shut the ballast off temporarily if there're any problems such as impulse suddenly or low input power. It takes about 3 minutes for the chip to adjust itself and the ballast will be working again. Once this happens, turn off the HID system and wait about 3 to 5 minutes. 6. Problem: Only one light works, although both lights are installed properly. Solution: Check the fuse at this side, change to a new one if it' s blown. 7. Problem: HID works when the engine is off, but it turns off automatically when the engine is on. Solution: For some latest cars such as 04 UP BMW, 04 UP Mercedes, the cars have computers to reject the outsource components such as HID conversion kit or non-original MP3 Players. Therefore, the only way to install the HID kit is to plug the HID ballasts to the car's battery directly. 8. Problem: The HID bulbs changes color when it turns on first time. Ballasts have some noise at the beginning also Solution: These are normal phenomenon. At the beginning, ballasts are getting the power from the automotive storage battery. So it's normal to have some noise. Ballast power is not stable initially. The bulbs may have different colors or even flicker a little bit. The light color will become normal once the power is stable. Xenon Lamp Chart For Different Brand Car 3. Problem: Both HID bulbs keep flickering with noise. Solution: 3.1. Check and make sure the HID bulbs wires have been connected to the ballasts wire properly and firmly. 3.2.Check the automobile storage battery, make sure it's not aged or empty. 05 www.yitoa.com/hid 06 www.yitoa.com/hid 07 www.yitoa.com/hid 08 www.yitoa.com/hid 09 www.yitoa.com/hid 10 www.yitoa.com/hid 11 www.yitoa.com/hid 12 www.yitoa.com/hid 13 www.yitoa.com/hid 14 www.yitoa.com/hid 15 www.yitoa.com/hid 16 www.yitoa.com/hid 17 www.yitoa.com/hid 18 www.yitoa.com/hid 19 www.yitoa.com/hid 20 www.yitoa.com/hid 21 www.yitoa.com/hid 22 www.yitoa.com/hid