Download PROFESSIONAL LOUDSPEAKER SYSTEM

user's manual
c
2 - SYSTEM'S DESCRIPTION
a
e
d
b
a -WIDE15P: compression driver (1.4" throat, 2.5" voice coil) featuring a neodymium magnet and titanium
diaphragm and loaded by a 80°x 60° wave-guide horn.
WIDE12P: compression driver (1" throat, 2.5" voice coil) featuring a neodymium magnet and titanium diaphragm
and loaded by a a 80°x 60° wave-guide horn.
b -WIDE15P: 15” woofer, featuring a 3” voce coil and a
powerful, external neodymium magnet.
WIDE12P: 12” woofer, featuring a 3” voce coil and a
powerful, external neodymium magnet.
c - Cabinet made from birch plywood, with high-impact, chip-resistant paint.
d -Steel protection grill with foam protection.
i
h
l
e -Bass reflex vent.
f - Three carrying handles.
g -Controls and connections panel.
h -2 anti-slip adjustable feet for use as a stage monitor.
i - Speaker-stand adapter.
f
650W
l - M10 threaded inserts.
g
1+/1 signal
2+/2 nc
CAUTION !
AV I S !
CONNECTION PANELS
1 - Input Speakon® connector (IN). Connect it to the power
amplifier or to the powered mixer output.
See connection examples at pages 19 - 20.
2 - Input link Speakon® connector (LINK). Wired in parallel
to the input connector, making it possible to drive another,
parallel connected, speaker system.
Always pay attention to the total impedance (see page 17)
NOTE: Connector 2 is not installed on models with 4-ohm
rated impedance (WIDE15P4 and WIDE12P4).
650W
1
1
INPUT
LINK
1+/1 signal
2+/2 nc
1+/1 signal
2+/2 nc
C A U TI O N !
CAUTION !
TO P R E VE N T E LE C TR IC SHOC K,
DO N OT R E M OVE C OVE R S
T O PR E V E NT E L E C T R IC S H O C K,
DO NO T R E MO V E C O V E R S
TO P R E VE N T R ISK OF FIR E ALWAYS R E P L AC E
FUSE S W ITH SAM E TYP E AN D R ATIN G
T O P R E V E NT R IS K O F F IR E A LWAY S R E P L A C E
F U S E S W IT H S A ME T Y P E A ND R AT ING
THIS AP PAR ATUS M UST B E E ARTHE D
AVI S !
P OUR É VITE R TOUT R ISQUE DE CH OC
E LE C TR IQUE , N E PAS OUVR IR
P OUR É VITE R TOUT R ISQUE DE FE U TOUJ OUR S R E M P LAC E R
L E FUSIBL E PAR UN DE M Ê M E S CAR AC TE R ISTIQUE S
C E T AP PAR E IL DOIT Ê TR E R E L IÉ A L A TE R R E
10
650W
ENGLISH
2
Use only loudspeaker cables (unscreened) having suitable
cross section (at least 2 x 1.5 mm2) and quality. Do not twist
or sharply bend the cables and do not allow for knots to
be formed, because they may result in insulation damage.
Do not use shielded cables (microphone/signal cables).
For detailed instructions about connector wiring, see par. 3.2.
T H IS A PPA R AT U S MU S T B E E A RT H E D
AVIS !
PO U R É V IT E R T O U T R IS Q U E DE C H O C
E L E C T R IQ U E , NE PA S O U V R I R
P O U R É V IT E R T O U T R IS Q U E DE F E U T O U JO U R S R E MPL A C E R
L E F U S IB L E PAR U N DE MÊ ME S C A R A C T E R IS T IQ U E S
C E T A P PA R E IL DO IT Ê T R E R E L IÉ A L A T E R R E
Never connect two power amplifiers to the same speaker system; this could cause serious damage to the
amplifiers.