Download TC1784 TriBoard Manual

User’s Manual, V 1.1, February 2012
TriBoard TC1784
Hardware Manual BGA292 V1.1
Microcontrollers
N e v e r
s t o p
t h i n k i n g .
Edition 2012-02
Published by Infineon Technologies AG,
Am Campeon 1-12,
85579 Neubiberg, Germany
© Infineon Technologies AG 2012.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as a guarantee of
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
User’s Manual, V 1.1, February 2012
TriBoard TC1784
Hardware Manual BGA292 V1.1
Microcontrollers
N e v e r
s t o p
t h i n k i n g .
TriBoard TC1784 Hardware Manual BGA292 V1.1
Revision History:
2012-02
Previous Version:
1.0
Page
Subjects (major changes since last revision)
all
change to hardware V1.1, remove TC1387
V 1.1
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
[email protected]
TriBoard TC1784
Hardware Manual
Table of Contents
Page
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2
2.1
2.2
2.3
TriBoard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-1
2-3
2-4
3
3.1
3.2
3.3
3.4
3.4.1
3.4.2
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.11.1
3.11.2
TriBoard Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MiniWiggler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FlexRay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Eeprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety option with SAK-CIC61508 (optional) . . . . . . . . . . . . . . . . . . . . . .
Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1
3-1
3-1
3-1
3-2
3-2
3-2
3-3
3-3
3-3
3-3
3-3
3-4
3-4
3-4
3-4
4
4.1
4.2
TriBoard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
HW Boot Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Assembly Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
5
5.1
5.2
5.3
TriBoard Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TC1784 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flexray Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OCDS connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
User’s Manual
I-1
5-1
5-1
5-1
5-1
7-1
7-2
7-4
7-4
7-4
7-5
7-5
7-5
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Table of Contents
Page
8.1
8.1.1
8.2
8.3
Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Changes on schematic version V1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
9
Keyword Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index-1
User’s Manual
I-2
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
List of Figures
Figure 2-1
Figure 2-2
Figure 3-1
Figure 4-1
Figure 4-2
Figure 4-3
Figure 4-4
Figure 4-5
Figure 4-6
Figure 4-7
Figure 4-8
Figure 7-1
Figure 7-2
Figure 7-3
Figure 7-4
Figure 7-5
Figure 7-6
Figure 7-7
Figure 7-8
Figure 8-1
Figure 8-2
Figure 8-3
Figure 8-4
Figure 8-5
Figure 8-6
Figure 8-7
Figure 8-8
Figure 8-9
Figure 8-10
Figure 8-11
Figure 8-12
Figure 8-13
User’s Manual
Page
TriBoard Block Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
TriBoard BGA292 V1.1 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Clock socket usage (XT301) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
HW Configuration TC1784 DIP-Switch . . . . . . . . . . . . . . . . . . . . . . . 4-1
Location of general optional resistors on Top Side . . . . . . . . . . . . . . 4-4
Location of general optional resistors on Bottom Side. . . . . . . . . . . . 4-4
Location of peripheral resistors on Top Side . . . . . . . . . . . . . . . . . . . 4-6
Location of peripheral resistors on Bottom Side . . . . . . . . . . . . . . . . 4-6
Location of resistors for safety device on Bottom Side . . . . . . . . . . . 4-7
Location of memories resistors on Top Side . . . . . . . . . . . . . . . . . . . 4-8
Location of memories resistors on Bottom Side . . . . . . . . . . . . . . . . 4-9
Connector for TC1784 - Pinout (Part I, Top View) . . . . . . . . . . . . . . . 7-2
Connector for TC1784 - Pinout (Part II, Top View) . . . . . . . . . . . . . . 7-3
Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
USB connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Flexray Pinout (SUBD-9 Plug) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
CAN connector pinout (IDC10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
OCDS connector pinout (IDC16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
DAP connector pinout (FTSH10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Schematic - Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Schematic - External Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
Schematic - Config, Clock and CIC61508 . . . . . . . . . . . . . . . . . . . . . 8-4
Schematic - Flexray, CAN and Eeprom . . . . . . . . . . . . . . . . . . . . . . . 8-5
Schematic - MiniWiggler, DAP and ETK . . . . . . . . . . . . . . . . . . . . . . 8-6
Schematic - GPTA, MSC, MLI and ADC . . . . . . . . . . . . . . . . . . . . . . 8-7
Schematic - Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Schematic - Connectors (Plug) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Schematic - Connectors (Socket) . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
Component Plot Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
Component Plot Bottom Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
Dimensioning (mil) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
Dimensioning (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
II-1
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
List of Figures
User’s Manual
Page
II-2
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
List of Tables
Table 4-1
Table 4-2
Table 4-3
Table 4-4
Table 4-5
Table 6-1
Table 6-2
Table 6-3
Table 6-4
Table 6-5
Table 6-6
Table 6-7
Table 6-8
Table 6-9
User’s Manual
Page
User Startup Modes for TC1784 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General optional resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resistors for peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resistors for safety device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resistors for memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety device Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bus Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bus Control Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
III-3
4-1
4-3
4-5
4-7
4-8
6-1
6-1
6-2
6-2
6-2
6-2
6-4
6-4
6-4
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
List of Tables
User’s Manual
Page
III-4
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Introduction
1
Introduction
We congratulate you on your purchase of the TriCore Evaluation Board. This kit is a
versatile tool, providing quick access to the capabilities of TriCore's powerful
architecture.
Applications can be developed easily. The Evaluation Board is equipped with a variety
of memories and peripherals for connection to the environment. There is also an
interface for the On Chip Debugging Features (OCDS1 and DAP). The kit also includes
several sets of development tools, which are stored on the included Evaluation Board
CD-ROM.
The Evaluation Board allows easily the development of TriCore applications with the
corresponding tools.
Subsequently, the applications can be downloaded and can be tested with the powerful
debugger software.
This TriBoard Hardware Manual familiarizes you with the TriCore Evaluation Board and
guides you through the initial configuration of the TriBoard.
For detailed technical information about the TC1784 please refer to the User Manual of
the device.
User’s Manual
1-1
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Introduction
User’s Manual
1-2
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Features
2
TriBoard Features
The TriBoard TC1784 is soldered with a the device TC1784 in the BGA292 package.
2.1
–
–
–
–
–
–
–
–
–
–
–
Summary of Features
Infineon’s TC1784 Controller in BGA292 Package
FlexRay Transceivers
Safety device (optional)
High Speed CAN Transceivers
USB to UART bridge
Crystal 20MHz (default), Oscillator or External Clock
USB miniWiggler for easy debugging
8 Low Power Status LEDs
8-DIP switches for configuration
access to all pins of controller
100mm x 160mm (EURO-Board)
Connectors
The TC1784 TriBoard offers a wide variety of connectors:
–
–
–
–
–
–
–
–
Standard power connector
USB connector for ASC Interface (ASC0) and miniWiggler
16-pin header for JTAG interface (OCDS)
10-pin header for DAP
2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1)
2 x SUB-D9 Plug connector for FlexRay
four 80-pin connectors (male) + four 80-pin connectors (female) with all I/O signals
optional ETK connector
Components
–
–
–
–
–
–
–
–
–
–
–
–
–
Infineon’s Next generation micro controller supply TLE 7368 - 3E
Three LEDs to validate power supply (5Volt / 3,3 Volt / 1,3 Volt)
LED indicating /HDRST (ESR0) active state
LED indicating activ miniWiggler
LED switched via DAS software
2x FlexRay Transceiver AS8221(AMS) or TJA1080 (NXP)
2 x Infineon’s High Speed CAN-Transceiver TLE 6250 GV33
Infineon’s Safety Device SAK-CIC61508(optional)
USB to UART bridge FT2232D (FTDI)
SPI eeprom (Atmel)
8 general purpose LEDs
Reset switch
8-pin Dip switch
User’s Manual
2-1
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Features
Zero Ohm Bridges
Zero Ohm resistors give the flexibility to configure the systems functionality
User’s Manual
2-2
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Features
2.2
Block Diagram
XTAL
CAN0
TxCAN0
PLL
RxCAN0
FLASH
16 Bit
TxCAN1
RxCAN1
TC1784
BUS
OCDS1
USB
B-TYPE
USB
miniWiggler
TXD0
TriCore
CPU
/CS0 or /CS1
BUS
SRAM
16 Bit
/CS0 or /CS1
ERAY A
SSC0
RXD0
8 LED’s
(P5.0 up to P5.7)
Serial EEPROM
Safety Device
SAK-CIC61508
optional
POWER SUPPLY WITH
SUPERSONIC
TLE7368-3E
ERAY B
FlexRay
Transceiver
SLSO00
Transceiver
ADDRESS and DATA BUS
BUS
CAN1
Figure 2-1
User’s Manual
TriBoard Block Schematic
2-3
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Features
2.3
Placement
USB
X701
1
X403 A1
OCDS1_CIC
BOOTCONFIG
ACT
OCDS1
L1
CAN0
U202
X302
S601
CAN1
+5V
TC1784
+3V3
JP203
X201
RST
P302
VDDP_CIC
1
1
RST
SYSDISC
X202
1
U106
U101
ERAY-B
X203
X301
1
P301
ETK
X401
RUN
U102
1 2 3 4 5 6 7 8
XT201
TriBoard-BGA292 V1.1
DAP
S201
1
X402
1
ERAY-A
SYSDISB
1
P5.0 P5.1 P5.2 P5.3 P5.4 P5.5 P5.6 P5.7
SYSDISA
P401
X704
1
1
1
+1V3
RST_CIC
POWER
X601
X703
+5,5V...+50V(+40V)
Figure 2-2
User’s Manual
S202
RESET_CIC
X702
1
1
1
1
TriBoard BGA292 V1.1 Placement
2-4
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Information
3
TriBoard Information
3.1
Power Supply
The Board has to be connected to a +5,5V to +50V (+40V) DC power supply. The
TriBoard generates internally +3.3V, +VDD and +5V. The power consumption is not
specified yet but a supply with 6V and 500mA should be sufficient. The pinout for the
supply connector is shown in Figure 7-3. There can be used any standard power pack
with a connector where the positive line is surrounded by the ground line.
Maximum power supply is reduced to +40V if the SAK-CIC61508 option is assembled.
+VDD is +1,3V for TC1784.
Applying a stable supply voltage causes the power on reset after a short period. The four
LED's (+5V, +3.3V, +1,3V) indicate the status of the on board generated voltage (if the
LEDs are assembled).
A manual reset is executed by pressing the reset button.
3.2
LEDs
There are 14 or 19 LEDs on board:
–
–
–
–
–
–
–
–
–
–
–
–
3.3
D501 up to D508 (blue)
D604 RST (red)
D505 +1V3 (green)
D606 +3V3 (green)
D607 +5V (green)
D402 ACT (green)
D401 RUN (red)
D204 RST_CIC (red)
D205 +VDDP_CIC (green)
D201 SYSDISA (red)
D202 SYSDISB (red)
D203 SYSDISC (red)
-> toogle LEDs connected to P5.0 ... P5.7
-> RESET LED indicate the reset state of the board
-> +1,3V power supply indication
-> +3,3V power supply indication
-> +5V power supply indication
-> on board MiniWiggler is ACTIV
-> Debug RUN mode (switched by DAS Server)
-> RESET LED indicate that the CIC is in reset
-> +VDDP for CIC power supply indication (+3,3V)
-> System Disable A (switched by CIC)
-> System Disable B (switched by CIC)
-> System Disable C (switched by CIC)
Clock
There are three possibilities to apply the CPU clock.
•
•
•
•
Large oscillator circuit (DIP14)
Small oscillator circuit (DIP8)
Crystal oscillator (default with 20MHz)
External clock generator
User’s Manual
3-1
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Information
The crystal oscillator and the oscillator circuit use the socket XT301. It's possible to apply
a 14pol DIP oscillator package or an 8pol DIP oscillator package.
OSCILLATOR
OSCILLATOR
XTAL
DIP14
DIP8
Figure 3-1
3.4
GND
External
Clock Input
Clock socket usage (XT301)
USB Connector
The USB connector is used for connection to a PC. Via the USB it is possible to power
the board, using the ASC0 as serial connection via USB and Debugging via DAS. For
the pinout of USB socket see Figure 7-4.
NOTE: Before connecting the board to the PC, make sure that the actual DAS software
is installed on the PC. For actual DAS software please contact your local FAE.
The software can also be found on the
DAS website
3.4.1
Serial Connection to PC
After the first connection of USB to a PC the needed driver will be installed automatically.
During this there will be created a new COM port on PC. This COM port can be used to
communicate with the board via ASC0 of the device (e.g. bootstrap loader).
3.4.2
MiniWiggler
MiniWiggler is a low cost debug tool which allows you access to the JTAG of the device.
Make sure that you have the latest DAS release. Debugging is possible via the DAS
Server JTAG over USB Chip. Please contact your prefered debug vendor for support of
DAS.
If you have connected the board to the PC and there runs the DAS server, then a working
connection is visible via the green ACTIV LED.
The status RUN LED is switched on/off through the DAS Server, depending on the used
debugger (client).
IMPORTANT: Make sure that there is no or a tristated connection on X401 (OCDS1) and
X402 (DAP) if the ACTIV LED is on.
User’s Manual
3-2
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Information
3.5
FlexRay
The board has 2 SUB-D connectors for FlexRay Communication with up to 10 Mbit/s.
For the pinout of the plugs see Figure 7-5.
The controller have an E-Ray modul and the transceiver are connected directly to the
controller
For more information look in the user manual for TC1784 and the schematics Figure 84.
3.6
Serial Eeprom
The SSC0 of the TC1784 is connected to a serial EEPROM with a size of 128K (16.384
x 8). As chip select for this EEPROM is used the line SLSO00 (P3.5). To disconnect
(disable) the EEPROM remove resistor R353.
3.7
MultiCAN
On the board are two CAN transceiver connected to the MultiCAN on TC1784 node 0
and 1. The transceivers are connected to two IDC10 plug. For the pinout of IDC10 plug
see Figure 7-6. You can use a IDC female connector with crimpconnector, flat cable and
SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.
3.8
Safety option with SAK-CIC61508 (optional)
The safety device is only assembled if the board is with the safety option.
The SAK-CIC61508 is connected to the SSC0 of the microcontroller and use the line
SLSO01 (P3.6) as chip select.
There are 4 LED’s for indication the state of the safety device (SYSDISA, SYSDISB,
SYSDISC, VDDP_CIC).
Sensor inputs A and B are always connected to the voltages of the Microcontroller. The
core voltage of the microcontroller to input A and the port voltage to input B.
With switch S202 it is possible to reset the safety device. If JP203 is set, then with S202
is also reset the microcontroller and the safety device is reset by a power on reset of the
microcontroller.
The safety device can be reprogrammed via JTAG and X203.
3.9
Other peripherals
For all other peripherals there are no special plugs on the board. The peripheral signals
are available on the different connectors. See “Connector Pin Assignment” on
Page 7-1.
Note: - SLSO00 is used as chip select for the serial eeprom on board.
User’s Manual
3-3
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Information
3.10
Toggle LED’s
Port 5 pin 0 up to pin 7 are connected to single LED’s (D501... D508) and can be
controlled by Software. This status LED’s are low active.
3.11
Debug System
3.11.1
OCDS1
The OCDS1 signals are connected to the IDC16 plug (X401). They work with the port
supply of +3.3V. For pinout of the connector see Figure 7-7. You can connect any
debugger to this connector.
The signals /BRKIN and /BRKOUT are not connected per default. If you need this signals
in the connector then assemble R425 and R424 with a 0R resistor.
If you connect a debug hardware make sure that the MiniWiggler (see “MiniWiggler”
on Page 3-2) is not activ (ACTIV LED is off) and on the DAP connector (X402) is no
hardware connected or the hardware is tristated.
If the ACTIV LED is on, then stop the active DAS Server JTAG over USB Chip and/or
remove the USB connection to the PC.
3.11.2
DAP
On the board is a DAP connector (X402) available. For pinout of this connector see
Figure 7-8. You can connect a DAP hardware here. If you use this connector make sure
that the MiniWiggler is not activ (ACTIV LED is off) and a connected OCDS1 hardware
is disconnected or tristated.
User’s Manual
3-4
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
HIGH
1
Figure 4-1
.7
P0
.6
.5
P0
P0
P0
.2
P0
P0
LOW
P0
HW Boot Configuration
.3
4.1
.1
TriBoard Configuration
P0
.0
4
.4
TriBoard Configuration
on
2
3
4
5
6
7
8
HW Configuration TC1784 DIP-Switch
The picture above shows the definition of the boot HW configuration switch. The
meaning of the switches will be described in the following table (Table 4-1).
Note: The ON position of the switch is equal to a logical LOW at the dedicated pin.
Table 4-1
User Startup Modes for TC1784
Note: The shadowed line indicates the default setting.
Note: ’x’ represents the don’t care state.
Note: 1 to 8 are the Dip Switch numbers
HWCFG[7...0] Type of Boot TC1784
1 2 3 4 5 6 7 8
11XXXXXX
Internal Start from Flash
X X X X X X O O
F F
F F
010XXXX0
Bootstrap Loader Mode, Generic Bootloader at O X X X X O O O
CAN pins
N
N F N
F
10101XX0
Bootstrap Loader Mode, ASC Bootloader
O X X O O O O O
N
F N F N F
F
F
F
10100XX0
Alternate Boot Mode, ASC Bootloader on fail
O X X O O O O O
N
N N F N F
F
F
User’s Manual
4-1
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Configuration
Table 4-1
User Startup Modes for TC1784
Note: The shadowed line indicates the default setting.
Note: ’x’ represents the don’t care state.
Note: 1 to 8 are the Dip Switch numbers
HWCFG[7...0] Type of Boot TC1784
1 2 3 4 5 6 7 8
1011XXXX
Alternate Boot Mode, Generic Bootloader at
CAN pins on fail
X X X X O O O O
F F N F
F F
F
all others
reserved; don’t use this combination
User’s Manual
4-2
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Configuration
4.2
Assembly Options
Table 4-2
General optional resistors
Component Description
R205
XTAL Rserial (default: assembled)
R206
XTAL Rparallel (default: not assembled)
R423
Connect /BRKOUT with MiniWiggler (default: not assembled)
R424
Connect /BRKOUT with OCDS1 connector (default: not assembled)
R427
Connect /BRKIN with USR1 of MiniWiggler (default: not assembled
R429
Connect /BRKIN with USR1 of DAP (default: not assembled
R425
Connect /BRKIN with OCDS1 connector(default: not assembled)
R428
Connect /TESTMODE with USR1 of MiniWiggler (default: not assembled
R430
Connect /TESTMODE with USR1 of DAP (default: not assembled
R426
Connect /TESTMODE with OCDS1 connector(default: not assembled)
R432
Connect debug reset with /PORST(default: assembled)
R431
Connect debug reset with /HDRST (default:not assembled)
R510
Connect +3,3V to all toggle LEDs (default: assembled)
R623
Connect reset switch with /PORST(default: assembled)
R624
Connect reset switch with /HDRST (default:not assembled)
R604
Connect P1.2 with MONSTBY of power device (default: not assembled)
R606
Connect P1.3 with WDO of power device (default: not assembled)
R609
Connect P1.15 with WDI of power device (default: not assembled)
User’s Manual
4-3
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Configuration
Note: All resistors are red marked in the following figures
CB406
P401
R407
R402
X704
C611
C608
R603
R608
R234
X201
S202
X702
1
1
Location of general optional resistors on Top Side
X804
U401
U404
R423
R418
R378
R335
R376
R340
R373
R604
R623
R624
R605
C614 R638
C613
Q601
R620
X802
X803
1
Figure 4-3
User’s Manual
C605
Q604
R617
D609
D602
R616
R507
R519
D608
Q603 R627
C609
R606 R628
C606
R619
Q602
R374
R618
R501
R379
R377
R375
R338
Q406 Q404 Q402
Q405 Q403 Q401
U304
R343
CB318
R339
R609
R430
R429
R372
R342
R411
R414
R341
C615
R502
R438
R503
R520
CB403
CB409
R416
R424
C612
R505
CB317
CB613
CB506
R509
CB501
R504
CB504
R508
CB622
CB605
CB604
CB621
CB602
CB502
R506
R319
R336
R437
R320
CB616
CB618
CB619
CB503
CB614
CB626
CB612
CB505
R613
R305
U602
CB627
C616
R625
R333
CB624
CB629
CB628
D603
CB609
CB608
R212
R610
R254
CB631
R207
Y201
R611
R253
R629
R255
CB617
CB610
CB611
CB623CB625
CB202
CB620
CB606
CB607
C201
CB110
CB109
U107
CB201
C202
CB630
R208
R121
CB603
R211
R118
R119
R120
C212
CB206
Y202
R252
CB615
R337
R425
R417
R419
Y401
CB408
R410
R334
R426
U305
R614
R202
R440
R415
R409
R420
CB405
U403
R344
C204
C203
R427 CB407
R205
R204
R219
R220
R221
R222
R223
R224
R225
R226
R203
R428
R412
R435
R421
1
R630
R256
R227
R602
R306
R257
R229
D204
R356
R354
R626
C205
R258
D202
D201
R353
R201
C206
R260
CB205
D205
U202
U203
U306
C610
R641
C209
R259
R213
R231
C208
CB104
R601
R639
R206
R239
JP203
CB208
R355
R436
R422
R240
R230
CB209
CB319
D605
1
C211
CB207
R228
C602 C604
U601
D606
X801
C210
R235
X202
R105
R104
R103
R112
R113
D607
X703
Figure 4-2
D203
CB102
U102
S201
R510
X302
U204
CB103
U104
C601
R233
R232
D507
D506
D505
D504
D503
D501
D508
C207
R115
R621
D604
R640
C607
CB204
R117
U103
R607
X601
D502
R308
R312
U101
R322
R622
CB314
S601
R332
R116
U106
CB601
R328
R329
R331
C304
X203
CB108
R431
CB315
R325
L601
R330
P302
T302
X301
R307
R432
R326
R371
1 2 3 4 5 6 7 8
XT201
R114
C303
D401
T301
R367
CB309
R309
U302
U303
CB316
R327
R515 R516 R517
R513 R514
R209
CB311
R311
R369
CB312
R323
R370
R321
R324
CB313
R511
R433
R313
R366
R317
R316
R315
R314
P301
CB310
R518
R434
R439
R210
R310
R368
X403
X401
R512
X402
R318
D402
CB404
CB402
R408
R401
1
D403
CB203
R405
C401
X701
1
R406
L401
CB401
CB101
U402
C603
R403
R404
1
D601
Location of general optional resistors on Bottom Side
4-4
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Configuration
Table 4-3
Resistors for peripherals
Component Description
R333
Connect P3.12 with RXD of CAN0 transceiver (default: assembled)
R339
Connect P3.14 with RXD of CAN1 transceiver (default: assembled)
R353
Connect P3.5 (SLSO00) with /CS of Eeprom (default: assembled)
R305
Connect P1.4 with EN of Flexray channel A (default: not assembled)
R306
Connect P1.6 with STBN of Flexray channel A (default: not assembled)
R379
Connect P0.14 with ERRN of Flexray channel A (default: assembled)
R319
Connect P1.5 with EN of Flexray channel B (default: not assembled)
R320
Connect P1.7 with STBN of Flexray channel B (default: not assembled)
R375
Connect P0.15 with ERRN of Flexray channel B (default: assembled)
R440
Connect P3.0 with TXD of USB to UART (default: assembled)
R505
Connect VAREF0 with VDDM (default: assembled)
R507
Connect VAGND0 with VSSM (default: assembled)
R508
Connect VFAREF with VDDMF (default: assembled)
R509
Connect VFAGND with VSSMF (default: assembled)
R519
Connect +5V with VDDM (default: assembled)
R520
Connect +3,3V with VDDM (default: not assembled)
User’s Manual
4-5
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Configuration
Note: All resistors are red marked in the following figures
CB406
P401
R407
R402
X704
C608
R603
R234
X201
S202
X702
1
1
Location of peripheral resistors on Top Side
X804
U401
U404
R423
R378
R373
R606 R628
R604
R623
R624
R605
Q604
C614 R638
C612
R617
C613
R507
Q601
X803
1
User’s Manual
D609
D602
R616
R620
X802
Figure 4-5
D608
Q603 R627
C609
R619
Q602
R374
R618
R501
R375
R376
C606
R609
R519
R379
R377
R335
R334
R424
R340
R343
CB318
R339
R503
R520
R429
R372
R342
R411
R430
R414
R418
R338
Q406 Q404 Q402
Q405 Q403 Q401
U304
R438
CB409
R410
R416
C605
R502
CB506
R509
CB501
R508
R504
CB504
R505
CB317
CB613
R319
R336
R437
R320
CB616
CB618
CB619
CB503
CB614
CB626
CB622
CB605
CB604
CB621
CB602
CB502
R506
CB609
CB608
CB612
CB505
R613
R305
U602
CB627
C616
R333
CB624
CB629
CB628
D603
R254
CB631
R207
Y201
R212
R629
R611
R253
R610
R630
R255
CB617
CB610
CB611
CB623CB625
CB202
CB620
CB606
CB607
C201
CB110
CB109
U107
CB201
C202
CB630
R208
R121
CB603
R211
R118
R119
R120
C212
CB206
Y202
R252
CB615
R419
R625
Y401
CB403
CB408
R341
C615
R425
R337
R426
R417
U305
R614
R202
R440
R415
R409
R420
CB405
U403
R344
C204
C203
R427 CB407
R205
R204
R219
R220
R221
R222
R223
R224
R225
R203
R428
R412
R435
R421
1
R306
C205
R256
D202
D201
R608
R602
R626
R257
R227
D204
R356
R354
R201
C206
R260
R258
D205
U202
R353
C209
CB205
R229
R228
U306
C610
R641
R226
R239
R213
R231
C208
CB104
R601
R639
R206
R259
JP203
CB208
R355
R436
R422
C210
R230
CB209
CB319
D605
1
R240
CB207
U203
C603
C602 C604
U601
D606
X801
C211
R235
X202
R105
R104
R112
R113
D607
X703
Figure 4-4
D203
CB102
U102
S201
R510
U204
CB103
U104
C601
R233
R232
D507
D506
D505
D504
D501
D508
C207
R115
X302
D604
R640
C611
CB204
R117
U103
R607
C607
D503
R308
R312
U101
R322
R622
CB314
S601
R332
R116
U106
CB601
R328
R329
R331
C304
L601
R330
P302
T302
X601
D502
R103
R307
CB315
R325
X203
CB108
R431
R326
R371
1 2 3 4 5 6 7 8
XT201
X301
R366
T301
R367
U303
CB316
R327
R515 R516 R517
R513 R514
R114
C303
D401
R432
U302
CB309
R309
CB311
R311
R369
CB312
R323
R370
R321
R324
CB313
R511
R433
R209
R313
R317
R316
R315
R314
P301
CB310
R518
R434
R439
R210
R310
R368
X403
X401
R512
X402
R318
D402
CB404
CB402
R408
R401
1
D403
CB203
R405
C401
X701
1
R406
L401
CB401
CB101
U402
R621
R403
R404
1
D601
Location of peripheral resistors on Bottom Side
4-6
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Configuration
Table 4-4
Resistors for safety device
Component Description
Voltage divider to adapt VDDP to VAREF of safety device (default:
assembled)
R239/R240
R252
Connect P3.6 (SLSO01) with /CS of safety device (default: assembled)
R253
Connect P3.2 (SSC0) to SCLK of safety device (default: assembled)
R254
Connect P2.11 (SSC1) to SCLK of safety device (default: not
assembled)
R255
Connect P3.4 (SSC0) to MTSR of safety device (default: assembled)
R256
Connect P2.12 (SSC1) to MTSR of safety device (default: not
assembled)
R257
Connect P3.3 (SSC0) to MRST of safety device (default: not assembled)
R258
Connect P2.10 (SSC1) to MRST of safety device (default: not
assembled)
Note: All resistors are red marked in the following figures
X801
X804
1
U401
R418
U404
R373
R374
R606 R628
R604
R623
R624
R605
Q604
C614 R638
C613
C612
R617
Q601
X803
1
User’s Manual
D609
D602
R616
R507
R620
X802
Figure 4-6
D608
Q603 R627
C606
R619
C609
R609
R519
R375
R376
R618
R501
R379
R377
Q602
R503
R520
R429
R378
R340
R344
R343
R339
CB318
R414
R424
R372
R342
R411
R430
R423
Q406 Q404 Q402
Q405 Q403 Q401
R338
R334
R438
CB409
R410
C605
R502
R504
CB503
CB506
R509
CB501
R508
R505
R613
R319
CB504
CB505
R437
R320
CB616
CB618
CB619
CB408
R336
U304
CB613
CB614
CB603
CB622
CB605
CB604
CB621
CB602
CB502
R506
CB609
CB608
R212
R305
U602
CB627
C616
R333
CB624
R419
R625
CB612
CB629
CB628
D603
R254
R610
R611
R253
R629
R255
CB631
R207
Y201
CB202
CB620
CB606
CB607
C201
CB617
CB610
CB611
CB623CB625
CB626
CB201
C202
CB110
CB109
U107
CB615
CB630
R211
R118
R119
R120
C212
CB206
R257
R208
R121
R630
R256
R252
Y202
C205
R258
C206
R260
CB205
R425
Y401
CB403
R416
R335
R426
R306
R337
R202
R626
R259
CB317
R239
C209
R417
U305
C210
R201
R614
C211
R240
R440
R415
R409
R420
R206
CB405
U403
R341
C615
C204
C203
R427 CB407
R205
R203
R204
R219
R221
R220
R224
R225
R222
R223
R226
R436
R422
R428
R412
R435
R421
1
1
D601
Location of resistors for safety device on Bottom Side
4-7
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Configuration
Table 4-5
Resistors for memories
Component Description
R103
Connect /CS1 to 16-bit SRAMs (default: assembled)
R104
Connect /CS0 to 16-bit SRAMs (default: not assembled)
R112
Connect /CS0 to 16-bit TSOP Flash (default: assembled)
R113
Connect /CS1 to 16-bit TSOP Flash (default: not assembled)
R118
Connect /CS0 to NAND Flash (default: not assembled)
R119
Connect /CS1 to NAND Flash (default: not assembled)
Note: All resistors are red marked in the following figures
CB406
P401
R407
R402
X704
U402
User’s Manual
D201
D202
R234
D205
R235
X202
R105
R104
R112
R113
R231
CB204
R117
U202
CB103
R230
U203
CB104
D606
CB207
C208
X302
U204
U103
D607
JP203
CB208
R229
R227
R601
U306
C610
R353
R641
R354
R608
X201
R355
CB209
CB319
D605
R228
C603
C602 C604
C608
C207
R115
R621
R622
CB314
S601
CB601
R213
D203
CB102
U102
S201
CB101
R510
U101
R639
R603
R233
R232
D508
D507
D506
D505
D504
D503
D501
R431
U104
R640
X601
C611
D204
R356
S202
R602
X703
C601
Figure 4-7
D502
R308
R116
U106
R607
C607
X203
CB108
D604
U601
R332
R114
C303
R328
R329
R331
R330
C304
1 2 3 4 5 6 7 8
R322
CB315
R325
L601
P302
T302
XT201
R103
R432
R326
R371
R515 R516 R517
R513 R514
X301
R366
R307
U303
CB316
R327
R309
U302
CB309
CB311
R311
R369
CB312
R323
R370
R321
R324
CB313
R511
R433
D401
R317
R316
T301
R367
R315
R314
P301
CB310
R518
R434
R209
R310
R368
X403
X401
R439
R210
R313
R318
D403
D402
R512
X402
X701
1
CB203
CB404
CB402
R401
R408
R405
C401
R312
CB401
1
R406
L401
R403
R404
X702
1
1
Location of memories resistors on Top Side
4-8
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Configuration
X801
X804
1
U401
R418
U404
R373
R374
R606 R628
R604
R623
R624
R605
C614 R638
C613
Q601
X803
1
User’s Manual
C605
Q604
R617
D609
D602
R616
R507
R620
X802
Figure 4-8
D608
Q603 R627
C606
R619
C609
R609
R519
R375
Q406 Q404 Q402
Q405 Q403 Q401
R338
R334
R423
R376
R618
R501
R379
R377
R340
R343
R339
CB318
R503
R520
R429
R378
R372
R342
R411
R430
R414
R424
C612
R505
R438
CB409
R410
Q602
R502
CB503
CB506
R509
CB501
R508
R504
CB504
CB505
R613
R319
R336
R437
R320
CB616
CB618
CB619
CB408
R344
CB613
CB626
CB614
CB617
CB610
CB611
CB609
CB608
R305
U602
CB627
C616
R333
CB624
R419
R625
CB612
CB629
CB628
D603
R254
CB631
R207
Y201
R212
R629
R611
R253
R610
R255
CB630
CB623CB625
CB202
CB620
CB606
CB607
C201
CB110
CB109
U107
CB201
C202
R121
CB603
R208
CB615
CB622
CB605
CB604
CB621
CB602
CB502
R506
R211
R118
R119
R120
C212
CB206
R257
R252
R630
R256
Y202
C205
R258
C206
R260
CB205
R425
R306
Y401
CB403
R416
R335
R426
R626
R337
R202
U304
R239
R259
CB317
C210
C209
R417
U305
R240
R614
C211
R201
R440
R415
R409
R420
R206
CB405
U403
R341
C615
C204
C203
R427 CB407
R205
R219
R203
R204
R221
R220
R224
R222
R225
R223
R226
R436
R422
R428
R412
R435
R421
1
1
D601
Location of memories resistors on Bottom Side
4-9
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Configuration
User’s Manual
4-10
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Software
5
TriBoard Software
5.1
Requirements
To install the software from your TriBoard CD you need a PC with Windows 2000,
Windows XP, Windows Vista, or Windows 7
5.2
Software Overview
The CD does not contain any tool. For the availablity for Demo Versions of the different
Tools, please contact the toolvendor directly (e.g. Tasking, Hitex, Lauterbach,
GreenHills, HighTec...). To install tools for compiling and debugging use seperat CD’s
from Toolvendors. There are also some application notes and software examples. The
data sheets of all used parts can be found in the “TriBoard_Components” directory. The
manuals for the microcontrollers and the Easy Kit are located in the “Manual” folder.
Some useful tools like Acrobat Reader are stored in the “Utilities” directory.
The current Errata Sheet can be found in the directory “Errata Sheet”. To make sure you
have always the most recent one, please contact your local FAE.
Note: For more details see the file ReadMe.txt.
5.3
Software Installation
To install tools for the TriCore insert the CD from the Toolvendor and start the file
“setup.exe” if the CD is not automatically started. Follow the instructions of the
installationprogram.
User’s Manual
5-1
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
TriBoard Software
User’s Manual
5-2
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Signal Description
6
Signal Description
For more information about the signals please see the user manual from TC1784 and/or
the schematics of the board.
Table 6-1
Power Signals
Short Name
Description
VCC_IN
Supply Input (5,5V...50V(40V))
VIN
Input voltage of power supply device
GND
Ground
VDD
Core Supply Voltage (1,3V)
VDDP
Port Supply Voltage (3,3V)
VDDFL3
Flash Supply Voltage (3,3V)
VDDESB
Emulation Stand-by SRAM Supply Voltage (1,3V)
VDDOSC
Main Oscillator Supply Voltage (1,3V)
VDDOSC3
Main Oscillator Supply Voltage (3,3V)
VSSOSC
Main Oscillator Ground
VSSM
ADC Analog Part Ground
VDDM
ADC Analog Part Supply Voltage (5V or 3,3V)
VSSMF
FADC Analog Part Ground
VDDMF
FADC Analog Part Supply Voltage (3,3V)
VDDAF
FADC Analog Part Logic Supply Voltage (1,3V)
VAGND0
ADC0 Reference Ground
VAREF0
ADC0 Reference Voltage (VDDM)
VAREF1
ADC1 Reference Voltage (VDDM)
VFAGND
FADC Reference Ground
VFAREF
FADC Reference Voltage (VDDMF)
VDDP_CIC
Port Supply Voltage safety device (3,3V)
VAGND_CIC
ADC Reference Ground safety device
VAREF_CIC
ADC Reference Voltage safety device (2,5V)
Table 6-2
Reset Signals
Short Name
Description
/PORST
Power On Reset
/HDRST (ESR0)
Hardware Reset
User’s Manual
6-1
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Signal Description
Table 6-3
Interrupt Signals
Short Name
Description
/NMI (ESR1)
Non Maskable Interrupt
/RESET_CIC
Reset safety device
Table 6-4
Clock Signals
Short Name
Description
XTAL1
Crystal Oscillator Input
XTAL2
Crystal Oscillator Output
XTAL1_CIC
Crystal Oscillator Input safety device
XTAL2_CIC
Crystal Oscillator Output safety device
Table 6-5
Debug Signals
Short Name
Description
/TRST
Test Reset
TCLK
Test Clock
TMS
Test Mode Select
TDI
Test Data Input
TDO
Test Data Output
/TESTMODE
Test Mode Select Input
/BRKIN
TriCore Breakpoint Input
/BRKOUT
TriCore Breakpoint Output
TCLK_CIC
Test Clock safety device
TMS_CIC
Test Mode Select safety device
TDI_CIC
Test Data Input safety device
TDO_CIC
Test Data Outpu safety device
MBC_CIC
Monitor & Bootstrap loader Control line safety device
Table 6-6
Peripheral Signals
Short Name
Description
P3.1
Transmit Data ASC0
P3.0
Receive Data ASC0
P3.8
Transmit Data ASC1
P3.9
Receive Data ASC1
User’s Manual
6-2
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Signal Description
Table 6-6
Peripheral Signals
P3.2
Clock Line SSC0
P3.3
Master Receive / Slave Transmit SSC0
P3.4
Master Transmit / Slave Receive SSC0
P3.5
Slave Select Output 0 (SSC0)
P3.13
CAN Transmitter Output 0
P3.12
CAN Receiver Input 0
P3.15
CAN Transmitter Output 1
P3.14
CAN Receiver Input 1
P2.4
MLI0 receive channel clock
P2.5
MLI0 receive channel ready output
P2.6
MLI0 receive channel valid input
P2.7
MLI0 receive channel data input
P2.0
MLI0 transmit channel clock
P2.1
MLI0 transmit channel ready input
P2.2
MLI0 transmit channel valid output
P2.3
MLI0 transmit channel data output
P2.11
Clock Line SSC0
P2.10
Master Receive / Slave Transmit SSC0
P2.12
Master Transmit / Slave Receive SSC0
P3.6
Slave Select Output 1 (SSC1)
P0 [0...7]
General Purpose I/O Port 0 (HWCFG)
P0 [8...15]
General Purpose I/O Port 0
P1[0...15]
General Purpose I/O Port 1
P2[0...13]
General Purpose I/O Port 2
P3[0...15]
General Purpose I/O Port 3
P4[0...3]
General Purpose I/O Port 4
P5[0...7]
General Purpose I/O Port 5 (used for LEDs)
P5[8...15]
General Purpose I/O Port 5
AN[0...35]
Analog Inputs
P6.1 / FCLP0A
MSC0 differential driver clock output positive A
P6.0 / FCLN0
MSC0 differential driver clock output negative
User’s Manual
6-3
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Signal Description
Table 6-6
Peripheral Signals
P6.3 / SOP0A
MSC0 differential driver serial data output positive A
P6.2 / SON0
MSC0 differential driver serial data output negative
Table 6-7
Safety device Signals
Short Name
Description
SENA
Sensor Input A
SENB
Sensor Input B
SENC
Sensor Input C
SEND
Sensor Input D
SCLK_CIC
Clock Line SAK-CIC61508
MRST_CIC
Master Receive / Slave Transmit SAK-CIC61508
MTSR_CIC
Master Transmit / Slave Receive SAK-CIC61508
/CS_CIC
Slave Select Input SAK-CIC61508
SYSDISA
System Disable Output A
SYSDISB
System Disable Output B
SYSDISC
System Disable Output C
Table 6-8
Bus Signals
Short Name
Description
D[0...15]
Address and Data Bus
A[16...20]
Address Bus
Table 6-9
Bus Control Signals
Short Name
Description
/CS[0...3]
Chip Selects
/BC[0...1]
Byte Controls
/RD
Read
/WR
Write
/ADV_ALE
Address Valid and Address Latch Enable
/WAIT
Wait Input
User’s Manual
6-4
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Connector Pin Assignment
7
Connector Pin Assignment
The TriBoard will be shipped with four male (plug) connectors on top layer and four
female (socket) connectors on bottom layer. The default connectors are 80-pol. Board to
Board connectors from Samtec:
http://www.samtec.com
Plug:
FTSH-140-02-L-DV-ES-A
Socket:
FLE-140-01-G-DV-A
Alternative there can be used the Board to Board System from Robinson Nugent:
http://www.robinsonnugent.com
Plug:
P50L-80P-AS-TGF
Socket:
P50L-80S-AS-TGF
Note: All connectors are pincompatible with the previous versions of TriBoard TC176X.
User’s Manual
7-1
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Connector Pin Assignment
7.1
TC1784 Connector / Top View
BUS EXPANSION (X701,X801)
GND
GND
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
/RD
/WR
Figure 7-1
User’s Manual
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
PERIPHERALS (X702,X802)
GND
GND
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
GND
GND
VCC_IN
VCC_IN
/ADV / ALE
/ESR1
GND
EN00 / P2.8
SDI0 / P2.13
FCLP0A / P6.1
FCLN0 / P6.0
SOP0A / P6.3
SON0 / P6.2
SLSO00_10 / P3.5
SLSO02_12 / P3.7
SLSO04_14 / P2.8
SLSO06 / P3.8
GND
XTAL1
XTAL2
RXD0 / P3.0
TXD0 / P3.1
RXDCAN0 / P3.12
TXDCAN0 / P3.13
SCLK0 / P3.2
MTSR0 / P3.4
MRST0 / P3.3
RXDCAN2 / P9.0
REQ0 / P3.10
REQ2 / P0.6
VDDESB
3V3
3V3
/CS2
/CS1
/CS0
/BC1
/BC0
/ADV / ALE
/WAIT
/CS3
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
GND
GND
VCC_IN
VCC_IN
/ESR0
GND
/PORST
EN01 / P2.9
SLSI1 / P2.13
SLSO01_11 / P3.6
SLSO03_13 / P2.1
SLSO05_15 / P2.9
SLSO17 / P1.10
GND
SYSCLK / P4.3
RXD1 / P3.9
TXD1 / P3.8
RXDCAN1 / P3.14
TXDCAN1 / P3.15
SCLK1 / P2.11
MTSR1 / P2.12
MRST1 / P2.10
TXDCAN2 / P9.1
REQ1 / P3.11
REQ3 / P0.7
GND
3V3
3V3
Connector for TC1784 - Pinout (Part I, Top View)
7-2
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Connector Pin Assignment
ADC (X703, X803)
VSSM
VSSM
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10
AN11
AN12
AN13
AN14
AN15
VSSM
VDDM
VFAGND
VAGND0
VAREF0
VSSM
AN32
AN33
AN34
AN35
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
VSSM
61
P10.5
63
P10.6
65
P10.7
67
3V3
69
AD0EMUX0 / P1.12 71
AD0EMUX1 / P1.13 73
AD0EMUX2 / P1.14 75
77
REQ5 / P0.15 79
Figure 7-2
User’s Manual
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
GPTA / MLI (X704,X804)
VSSM
VSSM
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
AN24
AN25
AN26
AN27
AN28
AN29
AN30
AN31
VSSMF
VDDMF
VFAREF
VAGND0
VAREF1
VSSM
GND
GND
GPTA0 / P0.0
GPTA1 / P0.1
GPTA2 / P0.2
GPTA3 / P0.3
GPTA4 / P0.4
GPTA5 / P0.5
GPTA6 / P0.6
GPTA7 / P0.7
GPTA8 / P0.8
GPTA9 / P0.9
GPTA10 / P0.10
GPTA11 / P0.11
GPTA12 / P0.12
GPTA13 / P0.13
GPTA14 / P0.14
GPTA15 / P0.15
GPTA16 / P1.0
GPTA17 / P1.1
GPTA18 / P1.2
GPTA19 / P1.3
GPTA20 / P1.4
GPTA21 / P1.5
GPTA22 / P1.6
GPTA23 / P1.7
GPTA24 / P1.8
GPTA25 / P1.9
GPTA26 / P1.10
GPTA27 / P1.11
GPTA28 / P4.0
GPTA29 / P4.1
GPTA30 / P4.2
GPTA31 / P4.3
TCLK1 / P5.11
TREADY1 / P5.10
TVALID1 / P5.9
TDATA1 / P5.8
3V3
3V3
VSSM
P10.8
P10.9
P10.10
3V3
P10.11
P10.12
P10.13
REQ4 / P0.14
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
GND
GND
GPTA32 / P2.0
GPTA33 / P2.1
GPTA34 / P2.2
GPTA35 / P2.3
GPTA36 / P2.4
GPTA37 / P2.5
GPTA38 / P2.6
GPTA39 / P2.7
GPTA40 / P5.0
GPTA41 / P5.1
GPTA42 / P5.2
GPTA43 / P5.3
GPTA44 / P5.4
GPTA45 / P5.5
GPTA46 / P5.6
GPTA47 / P5.7
GPTA82 / P9.2
GPTA83 / P9.3
GPTA84 / P9.4
GPTA85 / P9.5
GPTA86 / P9.6
GPTA87 / P9.7
EMGSTOP / P1.4
P10.0
P10.1
P10.2
P10.3
P10.4
RDATA1 / P5.12
RVALID1 / P5.13
RREADY1/ P5.14
RCLK1 / P5.15
3V3
3V3
Connector for TC1784 - Pinout (Part II, Top View)
7-3
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Connector Pin Assignment
7.2
Power connector pinout
+5,5V...50V(40V)
GND
Figure 7-3
USB connector pinout
Figure 7-4
7.4
2 (D-)
1 (Vbus)
3 (D+)
4 (GND)
USB connector Pinout
Flexray Pinout
6
Figure 7-5
User’s Manual
BP
2
BM
1
7
8
3
9
4
5
GND
7.3
Power connector pinout
Flexray Pinout (SUBD-9 Plug)
7-4
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Connector Pin Assignment
CAN connector pinout
4
6
8
1
0
1
3
5
7
9
Figure 7-6
CAN connector pinout (IDC10)
GND
/PORST
GND
GND
6
8
10
12
14
16
3
5
7
9
11
13
15
/BRKIN
TCK
TDI
/TRST
4
1
OCDS connector pinout (IDC16)
User’s Manual
Key
GND
GND
8
10
1
3
5
7
9
/RESET
6
USR1_IN
4
USR0_IO
2
DAP0
DAP1
Figure 7-8
GND
DAP connector pinout
+3V3
7.7
2
TDO
TMS
Figure 7-7
/BRKOUT
OCDS connector pinout
+3V3
7.6
GND
CANH
CANL
2
GND
7.5
DAP connector pinout (FTSH10)
7-5
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Connector Pin Assignment
User’s Manual
7-6
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Schematic and Layout
8
Schematic and Layout
8.1
Schematic
8.1.1
Changes on schematic version V1.1
• Change Power Supply to TLE7368-3E
User’s Manual
8-1
V 1.1, 2012-02
Figure 8-1
User’s Manual
8-2
A
B
C
D
1
1
/ESR0_/HDRST
/PORST
PORT[0..10]
2
/TESTMODE
JTAG..
/ESR0_/HDRST
/PORST
MiniWiggler and DAP
OCDS.sch
PORT[0..10]
PORT[0..10]
POWER SUPPLY
/ESR1_/NMI
Supply.sch
AN[0..35]
GPTA/MSC/MLI/ADC
GPTA_ADC.sch
2
3
XTAL[1..2]
/TESTMODE
JTAG..
PORT[0..10]
Clock. Config and Jtag
Clk_Cfg_Jtag.sch
3
4
4
A[0..20]
AD[0..15]
PORT[0..10]
/ESR0_/HDRST
IFLEX, CAN and Eeprom
IFlex_CAN_Eeprom.sch
/ESR0_/HDRST
BUS..CTRL
OnBoard Memories
Memories.sch
5
5
6
6
XTAL[1..2]
/ESR0_/HDRST
PORT[0..10]
BUS..CTRL
AD[0..15]
A[0..20]
NC1[0..80]
NC2[0..80]
AN[0..35]
8
7
8
9 of 9
ATV MC ACE PDA
Number:
Am Campeon 1-12
Revision: 1.1
D-85579 Neubiberg
Date:
10-Jan-2011
Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\TriBoard_BGA292.prj
Infineon Technologies AG
XTAL[1..2]
/ESR0_/HDRST
/PORST
/ESR1_/NMI
TriBoard BGA292 Project
Sheet:
/PORST
Connector Socket
NC3[0..80]
NC4[0..80]
Connectf.sch
NC4[0..80]
NC3[0..80]
NC2[0..80]
NC1[0..80]
A[0..20]
AD[0..15]
/ESR1_/NMI
AN[0..35]
Connector Plug
BUS..CTRL
PORT[0..10]
Connectm.sch
7
A
B
C
D
TriBoard TC1784
Hardware Manual
Schematic and Layout
Schematic - Project
V 1.1, 2012-02
A
B
C
1
U16
Y14
R17
U14
T14
Y15
W14
T15
U15
W15
Y17
W17
Y18
W18
Y19
V20
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
VCC
GND
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
VCC
GND
74LVC573APW
1D
2D
3D
4D
5D
6D
7D
8D
OE
LE
U104
74LVC573APW
1D
2D
3D
4D
5D
6D
7D
8D
OE
LE
U103
GND
A8
A9
A10
A11
A12
A13
A14
A15
CB104
100n
+3V3
GND
A0
A1
A2
A3
A4
A5
A6
A7
CB103
100n
BUS INTERFACE
19
18
17
16
15
14
13
12
20
10
19
18
17
16
15
14
13
12
20
10
+3V3
TC1784/TC1387-BGA292
2
P7.0 / AD0 / OUT32
P8.0 / A16 / OUT48 / OUT95
P7.1 / AD1 / OUT33
P8.1 / A17 / OUT49 / OUT96
P7.2 / AD2 / OUT34
P8.2 / A18 / OUT50 / OUT97
P7.3 / AD3 / OUT35
P8.3 / A19 / OUT51 / OUT98
P7.4 / AD4 / OUT36
P8.4 / A20 / OUT52 / OUT99
P7.5 / AD5 / OUT37
P8.5 / CS0 / OUT53 / OUT100
P7.6 / AD6 / OUT38
P8.6 / CS1 / OUT54 / OUT101
P7.7 / AD7 / OUT39
P8.7 / CS2 / OUT55 / OUT102
P7.8 / AD8 / OUT40
P8.8 / CS3 / OUT56 / OUT103
P7.9 / AD9 / OUT41
P8.9 / BC0 / OUT57 / OUT104
P7.10 / AD10 / OUT42
P8.10 / BC1 / OUT58 / OUT105
P7.11 / AD11 / OUT43
P8.11 / RD / OUT59 / OUT106
P7.12 / AD12 / OUT44
P8.12 / RD/WR / OUT60 / OUT107
P7.13 / AD13 / OUT45 P8.13 / ADV / ALE / OUT61 / OUT108
P7.14 / AD14 / OUT46
P8.14 / WAIT / OUT62 / OUT109
P7.15 / AD15 / OUT47
U101F
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
2
3
4
5
6
7
8
9
/ADV_ALE
2
3
4
5
6
7
8
9
1
11
1
11
GND
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
/ADV_ALE
GND
U19
U20
T19
T20
N20
R20
R19
P20
P19
P17
P16
N19
N17
N16
M17
3
/ADV_ALE
A16
A17
A18
A19
A20
/CS0
/CS1
/CS2
/CS3
/BC0
/BC1
/RD
/WR
/ADV_ALE
/WAIT
A8
A9
A10
A11
A12
A13
A14
A15
A0
A1
A2
A3
A4
A5
A6
A7
0R
0R_opt
R114
10K
+3V3
R105
10K
/ESR0_/HDRST
/RD
/WR
0R
/CS1 R113
/CS0 R112
/RD
/WR
/BC0
/BC1
0R_opt
/CS1 R103
/CS0 R104
+3V3
+3V3
4
4
10K
/ESR0_/HDRST
/CSBFL
/RD
/WR
R115
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
/CSRAM
/RD
/WR
/BC0
/BC1
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
12
26
28
11
47
25
24
23
22
21
20
19
18
8
7
6
5
4
3
2
1
48
17
16
9
6
41
17
39
40
1
2
3
4
5
18
19
20
21
43
44
24
25
26
27
42
22
23
28
VSS
VSS
VCC
VCC
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
12
34
VSS
VSS
VCC
RY/BY
NC/WP
NC/VPP
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15/A-1
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
5
+3V3
FLASH 1Mx16 3,3V 70ns
RESET
CE
OE
WE
BYTE
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
U106
10K
R120
27
46
37
15
14
13
30
32
34
36
39
41
43
45
29
31
33
35
38
40
42
44
+3V3
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
29
30
31
32
35
36
37
38
11
33
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
7
8
9
10
13
14
15
16
SRAM 256Kx16 3,3V 12ns
CS
OE
WE
LB
UB
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
U102
5
R118
0R_opt
GND
+3V3
/CSCFL
R119
0R_opt
0R
CB108
100n
+3V3
10K
R117
R116
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
GND
CB102 100n
3
CB101 100n
2
/CS0
8-3
/CS1
User’s Manual
6
6
17
16
9
8
18
A16
A17
/CSCFL
/RD
/WR
+3V3
R121
R/B
VSS
VSS
VSS
VSS
PRE/VSS
VCC
VCC
13
36
25
48
38
12
37
7
NANDFLASH4GX16_OPT
WP
CE
RE
WE
ALE
CLE
I/O8
I/O9
I/O10
I/O11
I/O12
I/O13
I/O14
I/O15
I/O0
I/O1
I/O2
I/O3
I/O4
I/O5
I/O6
I/O7
U107
/WAIT
+3V3
GND
Infineon Technologies AG
BUS..CTRL
A[0..20]
AD[0..15]
8
7
8
1 of 9
ATV MC ACE PDA
Number:
Am Campeon 1-12
Revision: 1.1
D-85579 Neubiberg
Date:
10-Jan-2011
Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\Memories.sch
Sheet:
TriBoard BGA292 External Memories
19
27
29
31
33
41
43
45
47
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
10K
26
28
30
32
40
42
44
46
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
7
CB110 100n
Figure 8-2
CB109 100n
D
1
A
B
C
D
TriBoard TC1784
Hardware Manual
Schematic and Layout
Schematic - External Memories
V 1.1, 2012-02
A17
A16
A
B
C
D
1
TDO_CIC
SYSDISB
SYSDISA
VDDP_CIC
GND
VAGND_CIC
VAREF_CIC
SEND
P1_0_CIC
P1_1_CIC
P1_5_CIC
/CS_CIC
P3_7_CIC
SYSDISB
SYSDISA
P3_2_CIC
P3_3_CIC
P3_4_CIC
P3_5_CIC
/RESET_CIC
P2_3_CIC
P2_4_CIC
P2_5_CIC
P2_6_CIC
P1_6_CIC
P1_7_CIC
TMS_CIC
TCK_CIC
TDO_CIC
TDI_CIC
SENA
SENB
SENC
R227
10K MBC_CIC
SCLK_CIC
MTSR_CIC
MRST_CIC
XTAL2_CIC
XTAL1_CIC
GND
VDDC_CIC
CON1X19_opt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
X202
620R
R235
620R
R234
620R
R233
GND
C212
10nF_opt
SEND
GND
VDDP_CIC
LS T67K
CON1X19_opt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
X201
GND
D203
LS T67K
D202
LS T67K
D201
SENC
C211
10nF_opt
1
11
12
13
14
2
3
4
MBC_CIC
TMS_CIC
TCK_CIC
TDO_CIC
TDI_CIC
SCLK_CIC
MTSR_CIC
MRST_CIC
VAGND_CIC
2
CB206
100n 24
25
27
28
29
9
10
38
/RESET_CIC
P1_0_CIC
P1_1_CIC
P1_5_CIC
P1_6_CIC
P1_7_CIC
VAREF_CIC
5
SAK-CIC61508
VAGND
VAREF
P1.0 / RXD_0
P1.1 / TXD_0
P1.5
P1.6
P1.7
P0.3 / SCLK_1
P0.4 / MTSR_1
P0.5 / MRST_1
MBC
TMS
P0.0 / TCK_0
P0.2 / TDO_0
P0.1 / TDI_0
RESET
XTAL2
XTAL1
VSSP
VDDC_CIC
P2.7 / AN7
P2.6 / AN6
P2.5 / AN5
P2.4 / AN4
P2.3 / AN3
P2.2 / AN2
P2.1 / AN1
P2.0 / AN0
P3.7
P3.6
P3.5
P3.4
P3.3
P3.2
P3.1
P3.0
VSSC
VDDC
2K
3
10
8
GND
GND
MRST_CIC
1
/RESET_CIC
MRST_CIC
MTSR_CIC
SCLK_CIC
/CS_CIC
OUT
GND
OUT
0R
3
6
4
1
3
5
7
9
11
13
15
VSSOSC
C208
22μF/10V
GND
R230 GND
opt
C207
1uF
VAREF_CIC
GND
R255
0R_opt
1
0R_opt
R258
0R_opt
RESET
JP203
0R
R257
0R
0R
R254
R256
R253
0R
R252
OCDS1_CIC
2
TMS
VCC
TDO
GND
CPUCLOCK
GND
TDI
PORST
TRST
BRKOUT
TCK
GND
BRKIN
OCDSE
N.C.
KEY
X203
Y201
XTAL2
C201 opt
opt
1
R206
opt
XTAL1
VDDP_CIC
3
VAGND_CIC
R231
REF192GS
GND SLEEP
V+
U204
GND
4
2
IN
0R
0R
R205
50R_opt
R204
R203
C204
33pF
GND
U203
TLE4274DV33
MBC_CIC R232
1K
TCK_CIC
TDI_CIC
TMS_CIC
TDO_CIC
CB205
220n
GND
CB207
100n
VDDP_CIC
GND
CB209
100n
VIN
4
GND
C203
33pF
ONLY ON REQUEST
P3_7_CIC GND
/CS_CIC
P3_5_CIC
P3_4_CIC
P3_3_CIC
P3_2_CIC
SYSDISA
SYSDISB
SEND
P2_6_CIC
P2_5_CIC
P2_4_CIC
P2_3_CIC
SENC
SENB
SENA
XTAL2
XTAL1
/TESTMODE
Crystal 20MHz
VCC
VCC
GND
OE
OE
XT201
CB204
100n
VDDC_CIC
GND
VDDP_CIC
R260
26
23
22
21
20
17
16
15
31
30
37
36
35
34
33
32
7
8
19
18
GND
11
14
7
1
4
XTAL[1..2]
/TESTMODE
3
CB203
100n
+3V3
GND
VDDP
22pF_opt
C206
CSTCR6M00G
U202
22pF_opt
C205
GND
VDDP_CIC
Y202
2
GND
6
S202
620R
R228
RESET_CIC
CB208
100n
R229
10K
XTAL2_CIC
XTAL1_CIC
XTAL2_CIC
XTAL1_CIC
/RESET_CIC
D204
GND
R239
1K6
R240
1K
VDDP
LS T67K
VDDP_CIC
GND
C210
10nF
C209
10nF
GND
/RESET_CIC
SENB
SENA
R259
0R
VDDCORE
2
1
8-4
3
User’s Manual
GND
Figure 8-3
2
1
C202
opt
5
/PORST
P2_10
P3_3
P2_12
P3_4
P2_11
P3_2
P3_6
5
VDDP_CIC
2
4
GND
6
8
/RESET_CIC
MBC_CIC
10
12
GND
14
16
GND
D205
LP T67K
R213
680R
VSSOSC
2
R207
opt
XTAL2
XTAL1
GND
R202
opt
R201
10K
+3V3
E14
D15
G4
B8
B18
P3_10 E15
P3_11 E13
P2_10
P3_3
JTAG / DAP / OCDS1
CLOCK & TESTMODE
TC1784
P0_7
P0_6
P0_5
P0_4
P0_3
P0_2
P0_1
P0_0
6
P3.10 / OUT92 / REQ0
P3.11 / OUT93 / REQ1
P2.10 / IN10 / OUT0 / MRST1A
P10_0
P10_1
P10_2
P10_3
680R
R226
680R
R224
680R
R222
680R
R220
P3.1 / OUT85 / TXD0A
P3.8 / SLSO06 / OUT90 / TXD1
P3.4 / OUT88 / MTSR0
P3.2 / OUT86 / SCLK0
P9.1 / OUT81 / TXDCAN2
P3.15 / OUT97 / TXDCAN1 / TXD1
P3.13 / OUT95 / TXDCAN0 / TXD0
+1V3
VSSOSC
/TRST
R211
8
GND
+3V3
JTAG..
GND
R210
10K_opt
R209
10K
+3V3
0R
CB201 0R
330n R208
VDDOSC3
D19
C20
B17
A7
A8
A17
A18
H4
A16
A15
A19
D16
P3_5
P3_6
P3_7
P2_12
P2_11
P3_4
P3_2
P9_1
P3_15
P3_13
P3_8
P3_1
CFG0
CFG1
CFG2
CFG3
CFG4
CFG5
CFG6
CFG7
1
2
3
4
5
6
7
8
Infineon Technologies AG
GND
16
15
14
13
12
11
10
9
7
8
2 of 9
ATV MC ACE PDA
Number:
Am Campeon 1-12
Revision: 1.1
D-85579 Neubiberg
Date:
10-Jan-2011
Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\Clk_Cfg_Jtag.sch
Sheet:
1
PORT[0..9]
DIPSW-8
S201
Switch ON means the corresponding signal is low.
Switch OFF means the corresponding signal is high.
TriBoard BGA292 Clock, Config, Jtag and CIC61508
P3.5 / SLSO00_10
P3.6 / SLSO01_11
P3.7 / SLSI01 / OUT89 / SLSO02_12
P2.12 / IN12 / OUT2 / MTSR1A / SOP0B
P2.11 / IN11 / OUT1 / SCLK1A / FCLP0B
P3.14 / OUT96 / RXDCAN1 / RXD1B
P3.3 / OUT87 / MRST0
680R
R225
680R
R223
680R
R221
680R
R219
ASC / CAN / SSC / EXT. REQ
P9.0 / OUT80 / RXDCAN2
D6
E6
D5
B5
VSSOSC
G20 TDO
K20
R212
CB202 0R
330n
VDDOSC
K19
H20
7
NOTE: S201 is for boot configuration (about configuration see the manual of assembled device).
P3.12 / OUT94 / RXDCAN0 / RXD0B
P3.9 / OUT91 / RXD1A
TC1784
VSSOSC
VDDOSC
VDDOSC3
TRST
TDO / DAP2 / BRKIN / BRKOUT
TCK / DAP0
TMS / DAP1
P10.0 / EVTO0
TDI / BRKIN / BRKOUT
P10.1 / EVTO1
P10.2 / EVTO2
P1.15 / BRKIN / BRKOUT
P10.3 / EVTO3
XTAL2
XTAL1
TESTMODE
U101B
P3.0 / OUT84 / RXD0A
U101C
P1_15
P3_14 B16
P9_0
G19
F20
H17
H19
J19
J20
F19
P1_15 F16
P3_12 B15
P3_9
P3_0
/TRST
TCK
TMS
TDI
XTAL2
XTAL1
/TESTMODE
6
A
B
C
D
TriBoard TC1784
Hardware Manual
Schematic and Layout
Schematic - Config, Clock and CIC61508
V 1.1, 2012-02
A
B
C
1
+3V3
2
10K
R356
10K
R355
GND
CB319
100n
+3V3
7
3
8
4
CS
SCK
SI
SO
AT25128N-10SI2.7
HOLD
WP
VCC
GND
U306
1
6
5
2
3
0R
R354
100K
R353
+3V3
P3_5
P3_2
P3_4
P3_3
4
0R
0R_opt
R375
ERRNB
P0_15
ENB
RXDB
TXENB
TXDB
P1_7
0R
R319
0R
R372
0R
R373
R374
0R_opt
R320
STBNB
P1_5
P0_9
P0_13
P0_11
0R
0R_opt
R379
ERRNA
P0_14
ENA
RXDA
TXENA
TXDA
P1_6
0R
R305
0R
R378
0R
R377
R376
0R_opt
R306
STBNA
P1_4
P0_8
P0_12
P0_10
P3_15
P3_14
P3_13
P3_12
4
5
R313
opt
INH1A
INH2A
WAKEA
9
3
4K7
R322
9
3
5
6
7
8
2
1
15
GND
R327
opt
INH1B
INH2B
WAKEB
2
1
15
4K7
STBNB
13
ERRNB
RXENB
12
R323
+3V3
TXDB
TXENB
RXDB
BGEB
ENB
R321
4K7
+3V3
GND
R326
opt
4K7
R308
5
6
7
8
4K7
STBNA
13
ERRNA
RXENA
12
R309
+3V3
GND
R325
opt
GND
R324
opt
GND
GND
GND
TXDA
TXENA
RXDA
BGEA
ENA
R307
4K7
+3V3
R312
opt
0R
R339
0R
R333
GND
R311
opt
GND
R310
opt
GND
5
GND
GND
AS8221
6
INH1
INH2
WAKE
ERRN
RXEN
STBN
EN
TXD
TXDEN
RXD
BGE
U303
AS8221
INH1
INH2
WAKE
ERRN
RXEN
STBN
EN
TXD
TXDEN
RXD
BGE
U302
100n
CB318 +5V
100n
CB317 +5V
6
1
2
3
4
1
2
3
4
GND
VBAT
VDD
VIO
NU / VBUF
BM
BP
NU / TRXD1
NU / TRXD0
GND
VBAT
VDD
VIO
NU / VBUF
BM
BP
NU / TRXD1
NU / TRXD0
0R
R340
6
8
5
7
6
8
5
7
R341
0R
+3V3
R335
0R
+3V3
R337
0R
R342 0R
120R R344
R343
0R
VIN
0R
GND
VIN
0R
GND
3
2
+5V
GND
+3V3
+5V
GND
0R
R368
GND
+5V
GND
opt
T302
R328
3
2
+3V3
GND
+5V
C304
10nF
R332
0R
GND
R330
51R
ONLY WITH NXP TJA1080
GND
0R
R371
opt
B82790-C0513-N201
R329
4
1
GND
Infineon Technologies AG
GND
GND
X2
5
9
4
8
3
7
2
6
1
X1
X2
5
9
4
8
3
7
2
6
1
X1
GND
GND
CHANNELB
P302
CHANNELA
P301
8
7
8
3 of 9
ATV MC ACE PDA
Number:
Am Campeon 1-12
Revision: 1.1
D-85579 Neubiberg
Date:
10-Jan-2011
Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\IFlex_CAN_Eeprom.sch
Sheet:
R331
51R
C303
10nF
R317
51R
2
4
6
8
10
2
4
6
8
10
R318
0R
ONLY WITH NXP TJA1080
GND
opt
R316
51R
CAN1
1
3
5
7
9
X302
CAN0
1
3
5
7
9
X301
TriBoard BGA292 IFlex, CAN and Eeprom
GND
16
14
19
4
20
17 BMB
18 BPB
10
11
0R
R370
R369
opt
T301
R314
B82790-C0513-N201
R315
4
1
GND
ONLY WITH NXP TJA1080
GND
16
14
19
4
20
17 BMA
18 BPA
10
11
0R
R367
R366
7
R336 0R
120R R338
ONLY WITH NXP TJA1080
TLE6250GV33
TXD CANL
GND INH
VCC
RM
RXD CANH
U305
0R
R334
TLE6250GV33
TXD CANL
GND INH
VCC
RM
RXD CANH
U304
CB309
100n
CB313
100n
D
PORT[0..10]
3
CB311
100n
2
CB310
100n
CB314
100n
8-5
CB312
100n
User’s Manual
CB315
100n
Figure 8-4
CB316
100n
1
A
B
C
D
TriBoard TC1784
Hardware Manual
Schematic and Layout
Schematic - Flexray, CAN and Eeprom
V 1.1, 2012-02
8-6
A
B
C
D
1
PORT[0..10]
R405
10K
VDD_USB
GND
CB406
100n
VDD_USB
1
2
3
4
7
4
8
5
ORG
CS
CLK
D
GND
10n
CB401
93LC46B-I/SN
DNC
Q
VCC
GND
U402
USB Connector
P401
L401
6
1
2
3
2
2K2
opt
R406
R407
33n
CB405
2
P1_15
P1_15
P1_15
P1_15
P1_0
PWREN
TEST
EECS
EESK
EEDATA
RESET
XTOUT
XTIN
RSTOUT
USBDP
USBDM
3V3OUT
100n
CB402
100n
P1_0
41
47
48
1
2
4
44
43
5
7
8
6
GND
0R_opt
R429
0R_opt
R427
0R_opt
R425
0R_opt
R424
0R_opt
R423
3
0R_opt
/TESTMODE
/TESTMODE
/TESTMODE
+3V3
2
4
GND
6
8
/DBGRST
/BRKOUT 10
12
GND
14
16
USR1_DAP
R430
BDBUS0
BDBUS1
40
39
38
37
36
35
33
32
1K
R414
OCDS1
4
/TESTMODE
VCC
TMS
GND
TDO
GND
CPUCLOCK
PORST
TDI
BRKOUT
TRST
GND
TCK
OCDSE
BRKIN
KEY
N.C.
X401
VDD_USB
10K
D401
LS T67K
R411
1K5
VDD_USB
VDD_USB
R408
ACBUS0
ACBUS1
ACBUS2
ACBUS3
15
13
12
11
10
30
29
28
27
26
ADBUS0
ADBUS1
ADBUS2
ADBUS3
ADBUS4
ADBUS5
ADBUS6
ADBUS7
24
23
22
21
20
19
17
16
FT2232D
BCBUS0
BCBUS1
BCBUS2
BCBUS3
SI/WUB
BDBUS0
BDBUS1
BDBUS2
BDBUS3
BDBUS4
BDBUS5
BDBUS6
BDBUS7
ACBUS0
ACBUS1
ACBUS2
ACBUS3
SI/WUA
0R_opt
R428
USR1
GND
ADBUS0
ADBUS1
ADBUS2
ADBUS3
ADBUS4
ADBUS5
ADBUS6
ADBUS7
100n
U401
GND
CB404
0R_opt
R426
/BRKIN
USR2
GND
470R
R401
100n
CB409
4
10K
R418
/BRKIN
/TESTMODE
1
3
5
7
9
11
13
15
BDBUS1 2
VDD_USB
BDBUS0 2
Q403
BSS138N
R416
10K
VDD_USB
2
Q406
BSS138N
5
2
10K
R419
Q404
BSS138N
USR1_DAP
USR1
TDI
/TRST
TCK
TMS
TDO
/DBGRST
USR2
Q405
BSS138N
33
33
Q402
BSS138N
P3_1
P1_3
/ESR0_/HDRST
/PORST
/PORST
G
G
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
/PORST
1
3
5
7
9
6
/TRST
TCK
TDI
TMS
/TRST
USR1
/DBGRST
/DBGRST
/PORST
DAI2
DAI1
GND
DAI4
DAI3
/ESR0_/HDRST
/BRKOUT_ETK
ETK_CON_opt
B1
A1
B2
A2
B3
A3
B4
A4
B5
A5
B6
A6
B7
A7
B8
A8
B9
A9
B10 A10
B11 A11
B12 A12
B13 A13
X403
TDO
VDDESB
/DBGRST
VDDP
TMS
TCK
TDI
22R_opt
R439
Infineon Technologies AG
JTAG..
8
7
8
4 of 9
ATV MC ACE PDA
Number:
Am Campeon 1-12
Revision: 1.1
D-85579 Neubiberg
Date:
10-Jan-2011
Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\OCDS.sch
Sheet:
TriBoard BGA292 miniWiggler, DAP and ETK
DAP2WIRE
VREF
DAP1
GND
DAP0
GND USER0_IO
KEY USER1_IN
GND
RESET
TMS
TCK
TDO
USR1_DAP
/DBGRST
USR2
2
4
6
8
10
1
TDO
GND
BAT54
D403
USR2
GND
R422
opt
3
7
TDO
X402
GND
R421
opt
GND
TCK
TDI
TMS
USR0
/TRST
/RESET
USR1
USR8
CB407
100n
+3V3
/BRKIN_ETK
/ESR0_/HDRST
0R
R432
0R_opt
R431
22R_opt
22R_opt
R438
R437
22R_opt
22R_opt
R436
22R_opt
R435
0R_opt
R434
R433
GND
+3V3
2
4
6
8
11
13
15
17
1
19
18
16
14
12
9
7
5
3
20
10
VDDESB
6
SN74AHCT244PW
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
VCC
GND
U404
P1_14
P1_2
P1_1
P1_0
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
VCC
GND
SN74AHC244PW
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
G
G
U403
R412
680R
D402
LP T67K
+3V3
P1_15
18
16
14
12
9
7
5
3
20
10
2
4
6
8
11
13
15
17
1
19
/ESR0_/HDRST
R440
0R
R420
1K
+3V3
GND
CB408
100n
2
R409
10K
+3V3
R415
10K
+3V3
VDD_USB
33
+3V3
Q401
BSS138N
R417
10K
+3V3
ACBUS3
ADBUS2
ADBUS0
ADBUS1
ADBUS3
ADBUS6
ACBUS0
ACBUS1
ACBUS2
ADBUS5
ADBUS4 2
R410
10K
VDD_USB
5
1
CB403
3
1
GND
P1_0
GND
VDD_USB
Y401
CSTCR6M00G
1K5
27R
R404
27R
R403
R402
GND
GND
C401
10μ/6V
VDD_USB
GND
GND
2
VDD_USB
MMZ1608R300A
1
3
3
42
VCC
VCC
46
AVCC
14
31
VCCIOA
VCCIOB
GND
GND
GND
GND
9
18
25
34
AGND
45
1
1
1
1
User’s Manual
P3_1
Figure 8-5
P3_0
1
A
B
C
D
TriBoard TC1784
Hardware Manual
Schematic and Layout
Schematic - MiniWiggler, DAP and ETK
V 1.1, 2012-02
Figure 8-6
User’s Manual
8-7
A
B
C
D
D9
J5
J4
K4
K5
L4
L5
A5
B4
A4
B3
A3
A2
C1
D2
E4
F5
P2_13
P9_2
P9_3
P9_4
P9_5
P9_6
P9_7
P10_4
P10_5
P10_6
P10_7
P10_8
P10_9
P10_10
P10_11
P10_12
P10_13
1
E12
D12
D11
E11
E9
E8
D8
E7
A14
B14
A13
B13
A12
B12
D7
B7
F17
E17
M16
K16
J16
H16
G16
G17
P0_0
P0_1
P0_2
P0_3
P0_4
P0_5
P0_6
P0_7
P0_8
P0_9
P0_10
P0_11
P0_12
P0_13
P0_14
P0_15
P1_0
P1_1
P1_2
P1_3
P1_4
P1_5
P1_6
P1_7
1
GPTA / LTCA / HWCFG / SSC / MLI / MSC
3
TC1784
2
P2.13 / IN13 / OUT3 / SLSI11 / SDI0
P9.2 / OUT82
P9.3 / OUT83
P9.4 / OUT84
P9.5 / OUT85
P9.6 / OUT86
P9.7 / OUT87
P10.4
P10.5
P10.6
P10.7
P10.8
P10.9
P10.10
P10.11
P10.12
P10.13
3
P6.1 / IN15 / OUT5 / OUT81 / FCLP0A
P6.0 / IN14 / OUT4 / OUT80 / FCLN0
P6.3 / IN25 / OUT7 / OUT83 / SOP0A
P6.2 / IN24 / OUT6 / OUT82 / SON0
P2.8 / SLSO04 / SLSO14 / EN00
P2.9 / SLSO05 / SLSO15 / EN01
P5.8 / RDATA0B / OUT89
P5.9 / RVALID0B / OUT90
P5.10 / RREADY0B / OUT91
P5.11 / RCLK0B / OUT92
P5.12 / TDATA0 / SLSO07 / OUT93
P5.13 / TVALID0B / SLSO16
P5.14 / TREADY0B / OUT94
P5.15 / TCLK0 / OUT95
P0.0 / IN0 / HWCFG0 / OUT0 / OUT56
P1.8 / IN24 / IN48 / MTSR1B / OUT24 / OUT48
P0.1 / IN1 / HWCFG1 / OUT1 / OUT57
P1.9 / IN25 / IN49 / MRST1B / OUT25 / OUT49
P0.2 / IN2 / HWCFG2 / OUT2 / OUT58
P1.10 / IN26 / IN50 / OUT26 / OUT50 / SLSO17
P0.3 / IN3 / HWCFG3 / OUT3 / OUT59
P1.11 / IN27 / IN51 / SCLK1B / OUT27 / OUT51
P0.4 / IN4 / HWCFG4 / OUT4 / OUT60
P4.0 / IN28 / IN52 / OUT28 / OUT52
P0.5 / IN5 / HWCFG5 / OUT5 / OUT61
P4.1 / IN29 / IN53 / OUT29 / OUT53
P0.6 / IN6 / HWCFG6 / REQ2 / OUT6 / OUT62
P4.2 / IN30 / IN54 / OUT30 / OUT54 / EXTCLK1
P0.7 / IN7 / HWCFG7 / REQ3 / OUT7 / OUT63
P4.3 / IN31 / IN55 / OUT31 / OUT55 / EXTCLK0
P0.8 / IN8 / RXDA0 / OUT8 / OUT64
P2.0 / IN32 / OUT32 / OUT28 / TCLK0
P0.9 / IN9 / RXDB0 / OUT9 / OUT65P2.1 / IN33 / TREADY0A / OUT33 / SLSO03 / SLSO13
P0.10 / IN10 / OUT10 / TXDA0
P2.2 / IN34 / OUT34 / OUT29 / TVALID0A
P0.11 / IN11 / OUT11 / TXDB0
P2.3 / IN35 / OUT35 / OUT30 / TDATA0
P0.12 / IN12 / OUT12 / TXENA
P2.4 / IN36 / RCLK0A / OUT36 / OUT31
P0.13 / IN13 / OUT13 / TXENB
P2.5 / IN37 / OUT37 / OUT110 / RREADY0A
P0.14 / IN14 / REQ4 / OUT14 / OUT70
P2.6 / IN38 / RVALID0A / OUT38 / OUT111
P0.15 / IN15 / REQ5 / OUT15 / OUT71
P2.7 / IN39 / RDATA0A / OUT39
P1.0 / IN16 / OUT16 / OUT72 / BRKIN / BRKOUT
P5.0 / IN26 / IN40 / OUT8 / OUT40
P1.1 / IN17 / OUT17 / OUT73
P5.1 / IN27 / IN41 / OUT9 / OUT41
P1.2 / IN18 / OUT18 / OUT74
P5.2 / IN28 / IN42 / OUT10 / OUT42
P1.3 / IN19 / OUT19 / OUT75
P5.3 / IN43 / OUT11 / OUT43
P1.4 / IN20 / EMGSTOP / OUT20 / OUT76
P5.4 / IN30 / IN44 / OUT12 / OUT44
P1.5 / IN21 / OUT21 / OUT77
P5.5 / IN31 / IN45 / OUT13 / OUT45
P1.6 / IN22 / OUT22 / OUT78
P5.6 / IN32 / IN46 / OUT14 / OUT46
P1.7 / IN23 / OUT23 / OUT79
P5.7 / IN47 / OUT15 / OUT47
U101D
2
P5_8
P5_9
P5_10
P5_11
P5_12
P5_13
P5_14
P5_15
P6_1
P6_0
P6_3
P6_2
P2_8
P2_9
B10
A10
B9
A9
E10
D10
P1_8
P1_9
P1_10
P1_11
P4_0
P4_1
P4_2
P4_3
P2_0
P2_1
P2_2
P2_3
P2_4
P2_5
P2_6
P2_7
P5_0
P5_1
P5_2
P5_3
P5_4
P5_5
P5_6
P5_7
H2
J2
J1
K2
K1
L2
L1
H1
L17
L19
L16
L20
T13
U13
W13
Y13
Y11
W11
U11
T11
Y12
W12
U12
T12
D1
E2
F4
G5
H5
E1
F1
F2
4
P5_7
P5_6
P5_5
P5_4
P5_3
P5_2
P5_1
P5_0
4
100R
R516
100R
R517
100R
R518
D505 LB T673
D506 LB T673
D507 LB T673
D508 LB T673
100R
100R
R515
D504 LB T673
LB T673
100R
R514
0R
100R
R512
100R
R513
R510
R511
D503 LB T673
D502 LB T673
D501
AN[0..35]
+3V3
5
5
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10
AN11
AN12
AN13
AN14
AN15
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
AN24
AN25
AN26
AN27
AN28
AN29
AN30
AN31
AN32
AN33
AN34
AN35
Y9
W9
T9
U8
Y8
W8
T8
T2
U7
Y6
Y5
Y4
Y3
Y2
W2
U5
W3
W5
W4
W6
W1
U4
V2
V1
T5
T4
U2
U1
T1
R5
R4
R2
R1
P5
P4
P1
ADC / FADC
TC1784
6
N5
N4
T6
U6
T7
P2
N1
N2
W7
Y7
T10
U10
U9
0R
R504
0R
VFAGND
0R
0R
CB506
100n R509
VSSMF
VAGND0
VFAREF
VDDMF
R508
0R
VDDM
+3V3
GND
R506
CB505
100n
VAREF1
VSSMF
CB503
10n
VDDMF
VSSM
CB502
R501
10n
VDDM
P1_12
P1_13
P1_14
7
VAGND0
Infineon Technologies AG
VSSM
VDDM
GND
+1V3
PORT[0..10]
0R
8
7
8
5 of 9
ATV MC ACE PDA
Number:
Am Campeon 1-12
Revision: 1.1
D-85579 Neubiberg
Date:
10-Jan-2011
Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\GPTA_ADC.sch
Sheet:
R505
0R
0R
R503
R502
+3V3
+5V
0R
CB504
100n R507
VAREF0
VSSMF
CB501
10n
VDDAF
0R_opt
R520
0R
R519
TriBoard BGA292 GPTA, MSC, MLI and ADC
AN0
P1.12 / IN16 / OUT16 / AD0EMUX0
AN1
P1.13 / IN17 / OUT17 / AD0EMUX1
AN2
P1.14 / IN18 / OUT18 / AD0EMUX2
AN3
AN4
AN5
AN6
VDDM
AN7
AN8
AN9
VSSM
AN10
AN11
AN12
AN13
VDDAF
AN14
AN15
AN16
VDDMF
AN17
AN18
AN19
VSSAF / VSSMF
AN20
AN21
AN22
AN23
VAREF0
AN24
VAREF1
AN25
AN26
AN27
VAGND0
AN28 / FAIN2P
AN29 / FAIN2N
AN30 / FAIN3P
AN31 / FAIN3N
VFAREF
AN32 / FAIN0P
AN33 / FAIN0N
AN34 / FAIN1P
VFAGND
AN35 / FAIN1N
U101E
6
A
B
C
D
TriBoard TC1784
Hardware Manual
Schematic and Layout
Schematic - GPTA, MSC, MLI and ADC
V 1.1, 2012-02
A
B
C
D
GND
C613
4μ7/10V
GND
C614
1μ/6V
Q_STBY
GND
BC848C
/PORST
82K
R616
1
/ESR1_/NMI
SS12
/ESR1_/NMI
RESET
R620
4K7
+3V3
R626
4K7
+3V3
GND
2
4K7
GND
R622
10K
GND_A
GND_A
GND_A
GND_A
GND_P
WDI
EN_uC
EN_IGN
SEL_LDO2
CCP
C2-
C2+
C1-
C1+
IN
IN
IN
C615
4μ7/10V
1
GND
SW
SW
BST
0R_opt
R609
3
R623
0R
RT
RO_1
RO_2
WDO
Q_T1
Q_T2
FB_EXT
DRV_EXT
Q_LDO2
Q_LDO1
FB/L_IN
IN_LDO2
Q602
BC848C
TLE7368-3E
GND
1
18
19
36
17
24
9
10
23
GND
GND_A
10K
10K
R602
R621
D607
LP T67K
R619
1K5
+5V
220n
+3V3
+3V3
R601
VIN
15
C602
100n 12
14
20
21
22
C603
100n 13
C604
16
CB601
100n
VIN
GND
C601
47μ/50V
S601
R625
1K
+3V3
+3V3
GND
D606
LP T67K
R618
680R
+3V3
/ESR0_/HDRST
/PORST
GND
D605
LP T67K
R617
620R
+3V3
Q604
1
SS12
C611
22μ/10V
+1V3
+1V3 D608 +3V3 D609 +5V
GND
C612
4μ7/10V
Q_T2
Q_T1
C610
22μ/10V
GND
C609
22μ/10V
+3V3
GND
+5V
GND
/ESR0_/HDRST
+1V3
2
2
X601
POWER VCC_IN D601
1
5,5V..50V
1
MBRS360T3
WDI
2
0R
Q_T1
Q_T2
C608
1n2
/ESR0_/HDRST
R624
0R_opt
1
R627
10K 1
R641
0R
0R
GND
4
R610
GND
VDDP
+1V3
GND
P1_15
P1_3
D604
LS T67K
R628
120R
Q603
BC858C
+3V3
+3V3
4K7_opt
0R
GND
0R
C607
4μ7/10V
R640
C606
47μ/10V
GND
0R_opt
+3V3
R608
R606
Q601
BDP949
VSW
4
P1_2
VSW
R607
R605
10K
+3V3
/PORST
GND
GND
+5V
L601
47μ/3A
D602
MBRS340T3
0R
+3V3
R639
R638
C605
680n
0R_opt
R603
10K R604
+3V3
25 WDO
RO_5V
3
4
7
8
31
32
6
30
29
5
28
26
27
33
35
/PORST
IN_STBY
Q_STBY
SEL_STBY MON_STBY
/PORST
Q_STBY
/ESR0_/HDRST
3
2
GND
GND
GND
GND
GND
3
GND
CB627
100n_opt
VIN
GND
GND
IN
U602
TLE4284DV_opt
GND
+1V3
GND
/PORST
/ESR0_/HDRST
/ESR1_/NMI
5
GND
100n
0R
E20
D20
E19
B1
B6
B11
B20
C2
C19
G2
M2
M19
W10
W16
GND
VDDCORE
100n
100n
CB609
CB607
CB608
100n
100n
100n
100n
100n
100n
CB606
CB605
CB604
CB603
CB602
CB623
100n
100n
CB624
CB625
GND
C616
10μ/10V_opt
VDDESB
100n
2
CB626
R611
OUT
ONLY WITH TC178XED AND ON REQUEST
PORT[0..10]
5
ADJ / GND
U601
3
6
W20
V19
T17
R16
P13
P8
N14
N7
H14
H7
G13
G8
PORST
ESR0
ESR1
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
3
2
GND
CB628
47n
VDDESB
POWER
GND
CB629
47n
ONLY WITH TC178XED
K17
VDDPF
34
11
3
2
M4
M5
VDDESB
VDDESB
GND
CB630
100n
2
2
3
J17
VDDPF3
1
CB612
100n
CB613
100n
CB614
100n
CB615
100n
CB616
100n
CB617
100n
CB618
100n
CB619
100n
CB620
100n
CB621
100n
CB622
100n
GND
3
1
+1V3
0R
GND
+3V3
+1V3
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
6
Infineon Technologies AG
TC1784/TC1387-BGA292
+3V3
8
7
8
6 of 9
ATV MC ACE PDA
Number:
Am Campeon 1-12
Revision: 1.1
D-85579 Neubiberg
Date:
10-Jan-2011
Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\Supply.sch
Sheet:
TriBoard BGA292 Power supply
GND
0R
R614
GND
U101A
P11
P10
P9
N12
N11
N10
N9
M14
M13
M11
M10
M8
M7
L14
L13
L12
L11
L10
L9
L8
L7
GND
GND
CB610
47n
VDDFL3
R630
CB611
47n
VDDPF3
0R
R629
BAT54_opt
D603
0R
R613
VDDPF
7
Y20
W19
U17
T16
P12
CB631
100n
D14
D13
VDDFL3
VDDFL3
8-8
VSS
VSS
VSS
VSS
VSS
User’s Manual
VSSP
VSSP
VSSP
VSSP
VSSP
VSSP
VSSP
VSSP
VSSP
VSSP
VSSP
VSSP
VSSP
VSSP
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
Figure 8-7
A6
A11
A20
B2
B19
D4
D17
E5
E16
G1
M1
M20
Y10
Y16
G9
G10
G11
G12
H9
H10
H11
H12
J7
J8
J10
J11
J13
J14
K7
K8
K9
K10
K11
K12
K13
K14
1
A
B
C
D
TriBoard TC1784
Hardware Manual
Schematic and Layout
Schematic - Power Supply
V 1.1, 2012-02
Figure 8-8
User’s Manual
8-9
A
B
C
D
NC1[1..80]
AD[0..15]
A[0..20]
1
PORT[0..10]
NC3[1..80]
ADC
BUS..CTRL
BUS EXPANSION
1
VSSM
2
+3V3
P1_12
P1_13
P1_14
NC3_77
P0_15
P10_5
P10_6
P10_7
VSSM
VDDM
VFAGND
VAGND0
VAREF0
VSSM
AN32
AN33
AN34
AN35
NC3_57
NC3_59
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10
AN11
AN12
AN13
AN14
AN15
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
NC1_37
NC1_39
NC1_41
NC1_43
NC1_45
NC1_47
NC1_49
NC1_51
NC1_53
NC1_55
NC1_57
NC1_59
NC1_61
NC1_63
NC1_65
NC1_67
/RD
/WR
NC1_73
NC1_75
NC1_77
NC1_79
2
+3V3
VSSM
P10_11
P10_12
P10_13
P0_14
NC3_80
P10_8
P10_9
P10_10
VSSMF
VDDMF
VFAREF
VAGND0
VAREF1
VSSM
NC3_50
NC3_52
NC3_54
NC3_56
NC3_58
NC3_60
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
AN24
AN25
AN26
AN27
AN28
AN29
AN30
AN31
VSSM
3
NC1_6
NC1_8
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
NC1_52
NC1_54
NC1_56
/CS2
/CS1
/CS0
NC1_64
NC1_66
/BC1
/BC0
/ADV_ALE
NC1_74
/WAIT
NC1_78
/CS3
GND
FTSH-140-02-L-DV-ES-A
X703
PLUG
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
FTSH-140-02-L-DV-ES-A
X701
PLUG
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
3
/ADV_ALE
AN[0..35]
4
/ADV_ALE
4
XTAL[1..2]
/ESR1_/NMI
5
5
VCC_IN
GND
+3V3
P0_0
P0_1
P0_2
P0_3
P0_4
P0_5
P0_6
P0_7
P0_8
P0_9
P0_10
P0_11
P0_12
P0_13
P0_14
P0_15
P1_0
P1_1
P1_2
P1_3
P1_4
P1_5
P1_6
P1_7
P1_8
P1_9
P1_10
P1_11
P4_0
P4_1
P4_2
P4_3
P5_11
P5_10
P5_9
P5_8
+3V3
VDDESB
XTAL1
XTAL2
P3_0
P3_1
P3_12
P3_13
P3_2
P3_4
P3_3
P9_0
P3_10
P0_6
GND
NC2_21
NC2_23
P2_8
P2_13
P6_1
P6_0
P6_3
P6_2
NC2_37
NC2_39
P3_5
P3_7
P2_8
P3_8
/ADV_ALE
NC2_11
P0_5
/ESR1_/NMI
NC2_17
GND
6
+3V3
P2_0
P2_1
P2_2
P2_3
P2_4
P2_5
P2_6
P2_7
P5_0
P5_1
P5_2
P5_3
P5_4
P5_5
P5_6
P5_7
NC4_38
NC4_40
P9_2
P9_3
P9_4
P9_5
P9_6
P9_7
NC4_54
NC4_56
P1_4
P10_0
P10_1
P10_2
P10_3
P10_4
P5_12
P5_13
P5_14
P5_15
GND
FTSH-140-02-L-DV-ES-A
X704
PLUG
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
P4_3
NC2_54
P3_9
P3_8
P3_14
P3_15
P2_11
P2_12
P2_10
P9_1
P3_11
P0_7
/PORST
NC2_24
P2_9
NC2_28
NC2_30
NC2_32
NC2_34
NC2_36
NC2_38
P2_13
P3_6
P2_1
P2_9
P1_10
+3V3
GND
GND
GND
NC2_10
NC2_12
NC2_14
/ESR0_/HDRST
NC2_18
VCC_IN
FTSH-140-02-L-DV-ES-A
X702
PLUG
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
6
7
GPTA / MLI
Infineon Technologies AG
7
8
7 of 9
ATV MC ACE PDA
Number:
Am Campeon 1-12
Revision: 1.1
D-85579 Neubiberg
Date:
10-Jan-2011
Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\Connectm.sch
Sheet:
8
TOP
PERIPHERALS
TriBoard BGA292 Connectors plug
NC4[1..80]
/PORST
/ESR0_/HDRST
NC2[1..80]
A
B
C
D
TriBoard TC1784
Hardware Manual
Schematic and Layout
Schematic - Connectors (Plug)
V 1.1, 2012-02
Figure 8-9
User’s Manual
8-10
A
B
C
D
NC1[1..80]
AD[0..15]
A[0..20]
1
PORT[0..10]
NC3[1..80]
ADC
BUS..CTRL
BUS EXPANSION
1
VSSM
2
+3V3
P1_12
P1_13
P1_14
NC3_77
P0_15
P10_5
P10_6
P10_7
VSSM
VDDM
VFAGND
VAGND0
VAREF0
VSSM
AN32
AN33
AN34
AN35
NC3_57
NC3_59
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10
AN11
AN12
AN13
AN14
AN15
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
NC1_37
NC1_39
NC1_41
NC1_43
NC1_45
NC1_47
NC1_49
NC1_51
NC1_53
NC1_55
NC1_57
NC1_59
NC1_61
NC1_63
NC1_65
NC1_67
/RD
/WR
NC1_73
NC1_75
NC1_77
NC1_79
2
FLE-140-01-G-DV-A
X803
SOCKET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
FLE-140-01-G-DV-A
X801
SOCKET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
+3V3
VSSM
P10_11
P10_12
P10_13
P0_14
NC3_80
P10_8
P10_9
P10_10
VSSMF
VDDMF
VFAREF
VAGND0
VAREF1
VSSM
NC3_50
NC3_52
NC3_54
NC3_56
NC3_58
NC3_60
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
AN24
AN25
AN26
AN27
AN28
AN29
AN30
AN31
VSSM
3
NC1_6
NC1_8
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
NC1_52
NC1_54
NC1_56
/CS2
/CS1
/CS0
NC1_64
NC1_66
/BC1
/BC0
/ADV_ALE
NC1_74
/WAIT
NC1_78
/CS3
GND
3
/ADV_ALE
AN[0..35]
4
/ADV_ALE
4
XTAL[1..2]
/ESR1_/NMI
5
5
VCC_IN
GND
+3V3
P0_0
P0_1
P0_2
P0_3
P0_4
P0_5
P0_6
P0_7
P0_8
P0_9
P0_10
P0_11
P0_12
P0_13
P0_14
P0_15
P1_0
P1_1
P1_2
P1_3
P1_4
P1_5
P1_6
P1_7
P1_8
P1_9
P1_10
P1_11
P4_0
P4_1
P4_2
P4_3
P5_11
P5_10
P5_9
P5_8
+3V3
VDDESB
XTAL1
XTAL2
P3_0
P3_1
P3_12
P3_13
P3_2
P3_4
P3_3
P9_0
P3_10
P0_6
GND
NC2_21
NC2_23
P2_8
P2_13
P6_1
P6_0
P6_3
P6_2
NC2_37
NC2_39
P3_5
P3_7
P2_8
P3_8
/ADV_ALE
NC2_11
P0_5
/ESR1_/NMI
NC2_17
FLE-140-01-G-DV-A
X804
SOCKET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
FLE-140-01-G-DV-A
X802
SOCKET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
P4_3
NC2_54
P3_9
P3_8
P3_14
P3_15
P2_11
P2_12
P2_10
P9_1
P3_11
P0_7
/PORST
NC2_24
P2_9
NC2_28
NC2_30
NC2_32
NC2_34
NC2_36
NC2_38
P2_13
P3_6
P2_1
P2_9
P1_10
6
+3V3
P2_0
P2_1
P2_2
P2_3
P2_4
P2_5
P2_6
P2_7
P5_0
P5_1
P5_2
P5_3
P5_4
P5_5
P5_6
P5_7
NC4_38
NC4_40
P9_2
P9_3
P9_4
P9_5
P9_6
P9_7
NC4_54
NC4_56
P1_4
P10_0
P10_1
P10_2
P10_3
P10_4
P5_12
P5_13
P5_14
P5_15
GND
+3V3
GND
GND
GND
NC2_10
NC2_12
NC2_14
/ESR0_/HDRST
NC2_18
VCC_IN
GND
6
7
GPTA / MLI
PERIPHERALS
Infineon Technologies AG
7
8
8 of 9
ATV MC ACE PDA
Number:
Am Campeon 1-12
Revision: 1.1
D-85579 Neubiberg
Date:
10-Jan-2011
Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\Connectf.sch
Sheet:
8
BOTTOM
TriBoard BGA292 Connectors socket
NC4[1..80]
/PORST
/ESR0_/HDRST
NC2[1..80]
A
B
C
D
TriBoard TC1784
Hardware Manual
Schematic and Layout
Schematic - Connectors (Socket)
V 1.1, 2012-02
P301
P302
X601
L401
R318
X402
C401
R310
R368
CB310
R327
T302
C304
R371
C601
1
X401
D402
R326
CB315
R325
CB311
R311
R369
CB312
R323
R370
R321
R332
C611
C607
R405
R406
U402
R307
R401
R324
CB313
CB401
1
R432
R309
D403
R431
D604
X403
D501
R602
R607
R639
R608
R641
C610
R601
D605
D606
D607
R209
R439
R210
R433
R434
R511
X704
D507
D506
D505
D503
X703
XT201
U101
R515 R516 R517
R513 R514
D504
R407
D502
R512
CB203
D508
R510
CB406
1 2 3 4 5 6 7 8
R518
1
1
CB101
R114
R402
R112
R113
U104
U103
CB103
R115
CB108
R103
R403
R404
R317
R330
C303
R316
CB309
R314
R329
CB316
R315
R328
L601
R331
CB404
CB402
R408
D401
T301
R367
U302
U303
R640
R308
R313
R366
CB314
CB601
R603
R312
S601
U601
R621
C602 C604
C608
R322
R622
X301
X302
C603
X701
U106
CB102
X702
R354
R353
CB209
CB319
U203
U102
R104
CB104
8-11
C208
JP203
D204
R230
CB207
U204
R356
U306
R355
R232
C207
R117
R116
X203
R231
R228
D201
D203
CB208
R229
D202
R234
D205
S202
R227
CB204
R213
R233
R235
User’s Manual
U202
8.2
X201
P401
TriBoard TC1784
Hardware Manual
Schematic and Layout
Layout
Figure 8-10 Component Plot Top Layer
V 1.1, 2012-02
X202
R105
S201
TriBoard TC1784
Hardware Manual
Schematic and Layout
CB206
R240
R239
C205
C211
C210
Y202
C212
R252
CB109
C209
R257
R255
C206
R259
CB205
R256
R258
R253
R254
R260
X801
U107
X802
R120
R119
R118
CB110
R121
R208
R620
1
1
R630
C202
C201
R629
CB627
R611
R225
CB202
CB620
CB606
CB607
U602
R226
Y201
R212
R610
R221
R220
R219
R203
CB613
R204
R205
C204
X804
R436
R422
U403
R421
R435
R412
1
CB408
R410
R414
R423
R416
R418
R428
R417
Q406 Q404 Q402
Q405 Q403 Q401
R427 CB407
R415
R409
R420
R424
R376
R377
U404
Y401
CB403
CB409
D609
R411
R430
CB405
U401
R429
R379
R375
R378
R372
R373
R374
Q602
R338
R440
R419
R334
R336
R335
R337
R201
R625
R340
U304
R426
R425
R333
R437
R438
R344
R626
R306
R305
CB317
R342
D608
C606
D602
D601
C609
R623
C605
Q601
R343
U305
R341
C615
R624
Q603 R627
1
R605
R609
R606 R628
R604
R616
C613
C614 R638
R319
R617
C612
R320
R619
R618
R501
R339
CB318
R202
R503
R504
X803
Q604
C203
R206
CB612
R502
R222
CB614
CB616
CB503
R614
CB626
CB618
CB619
R507
R519
R520
CB506
R509
CB501
R508
R223
CB617
CB610
CB611
CB624
CB504
CB615
CB623CB625
CB630
CB603
CB622
CB605
CB604
CB621
CB602
CB502
R506
CB505
R505
CB631
CB629
CB628
R613
D603
CB201
C616
CB609
CB608
R224
R211
R207
Figure 8-11 Component Plot Bottom Layer
User’s Manual
8-12
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Schematic and Layout
8.3
Layout with Dimensioning
The following dimensions should be used for development of extension boards.
Note: these are the pictures from the TriBoard TC10GP. Connectors X801...X804 are on
the same place.
Figure 8-12 Dimensioning (mil)
User’s Manual
8-13
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Schematic and Layout
Figure 8-13 Dimensioning (mm)
User’s Manual
8-14
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Keyword Index
9
Keyword Index
This section lists a number of keywords which refer to specific details of the TriBoard
TC1784 in terms of its architecture, its functional units or functions. This helps to quickly
find the answer to specific questions about the TriBoard TC1784.
A
HWCFG 4-1
ACTIV LED 3-2
Assembly Options 4-3
I
B
Bus Control Signals 6-4
Bus Signals 6-4
Interrupt Signals 6-2
L
DAP 3-4
DAP connector pinout 7-5
Debug Signals 6-2
Debug System 3-4
Dimensioning 8-13
Layout 8-11
LEDs 3-1
Location of general optional resistors on
Bottom Side 4-4
Location of general optional resistors on
Top Side 4-4
Location of memories resistors on Bottom
Side 4-9
Location of memories resistors on Top
Side 4-8
Location of peripheral resistors on Bottom
Side 4-6
Location of peripheral resistors on Top
Side 4-6
Location of resistors for safety device on
Bottom Side 4-7
E
M
C
CAN connector pinout 7-5
Clock 3-1
Clock Signals 6-2
Connector Pin Assignment 7-1
CPU clock 3-1
Crystal oscillator 3-1
D
F
manual reset 3-1
MiniWiggler 3-2
MultiCAN 3-3
FlexRay 3-3
Flexray Pinout 7-4
O
External clock 3-1
G
General optional resistors 4-3
OCDS connector pinout 7-5
OCDS1 3-4
oscillator circuit 3-1
Other peripherals 3-3
H
HW Boot Configuration 4-1
User’s Manual
9-1
V 1.1, 2012-02
TriBoard TC1784
Hardware Manual
Keyword Index
P
Peripheral Signals 6-2
Power connector pinout 7-4
Power Signals 6-1
power supply 3-1
R
reset 3-1
Reset Signals 6-1
Resistors for memories 4-8
Resistors for peripherals 4-5
Resistors for safety device 4-7
Robinson Nugent 7-1
RUN LED 3-2
S
Safety device Signals 6-4
Safety option 3-3
Samtec 7-1
Schematic 8-1
Schematic and Layout 8-1
Serial Connection to PC 3-2
Serial EEPROM 3-3
Serial Eeprom 3-3
Signal Description 6-1
Software 5-1
status LED 3-4
Supply 3-1
T
Toggle LED’s 3-4
TriBoard BGA292 V1.1 Placement 2-4
TriBoard Software 5-1
Type of Boot TC1784 4-1
U
USB Connector 3-2
USB connector pinout 7-4
User’s Manual
9-2
V 1.1, 2012-02
((3))
http://www.infineon.com
Published by Infineon Technologies AG