Download TC1784 TriBoard Manual
Transcript
User’s Manual, V 1.1, February 2012 TriBoard TC1784 Hardware Manual BGA292 V1.1 Microcontrollers N e v e r s t o p t h i n k i n g . Edition 2012-02 Published by Infineon Technologies AG, Am Campeon 1-12, 85579 Neubiberg, Germany © Infineon Technologies AG 2012. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. User’s Manual, V 1.1, February 2012 TriBoard TC1784 Hardware Manual BGA292 V1.1 Microcontrollers N e v e r s t o p t h i n k i n g . TriBoard TC1784 Hardware Manual BGA292 V1.1 Revision History: 2012-02 Previous Version: 1.0 Page Subjects (major changes since last revision) all change to hardware V1.1, remove TC1387 V 1.1 We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: [email protected] TriBoard TC1784 Hardware Manual Table of Contents Page 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 2 2.1 2.2 2.3 TriBoard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2-1 2-3 2-4 3 3.1 3.2 3.3 3.4 3.4.1 3.4.2 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.11.1 3.11.2 TriBoard Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MiniWiggler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FlexRay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Eeprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety option with SAK-CIC61508 (optional) . . . . . . . . . . . . . . . . . . . . . . Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3-1 3-1 3-1 3-2 3-2 3-2 3-3 3-3 3-3 3-3 3-3 3-4 3-4 3-4 3-4 4 4.1 4.2 TriBoard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 HW Boot Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Assembly Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 5 5.1 5.2 5.3 TriBoard Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TC1784 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flexray Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OCDS connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 User’s Manual I-1 5-1 5-1 5-1 5-1 7-1 7-2 7-4 7-4 7-4 7-5 7-5 7-5 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Table of Contents Page 8.1 8.1.1 8.2 8.3 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Changes on schematic version V1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11 Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 9 Keyword Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index-1 User’s Manual I-2 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual List of Figures Figure 2-1 Figure 2-2 Figure 3-1 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 7-1 Figure 7-2 Figure 7-3 Figure 7-4 Figure 7-5 Figure 7-6 Figure 7-7 Figure 7-8 Figure 8-1 Figure 8-2 Figure 8-3 Figure 8-4 Figure 8-5 Figure 8-6 Figure 8-7 Figure 8-8 Figure 8-9 Figure 8-10 Figure 8-11 Figure 8-12 Figure 8-13 User’s Manual Page TriBoard Block Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 TriBoard BGA292 V1.1 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Clock socket usage (XT301) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 HW Configuration TC1784 DIP-Switch . . . . . . . . . . . . . . . . . . . . . . . 4-1 Location of general optional resistors on Top Side . . . . . . . . . . . . . . 4-4 Location of general optional resistors on Bottom Side. . . . . . . . . . . . 4-4 Location of peripheral resistors on Top Side . . . . . . . . . . . . . . . . . . . 4-6 Location of peripheral resistors on Bottom Side . . . . . . . . . . . . . . . . 4-6 Location of resistors for safety device on Bottom Side . . . . . . . . . . . 4-7 Location of memories resistors on Top Side . . . . . . . . . . . . . . . . . . . 4-8 Location of memories resistors on Bottom Side . . . . . . . . . . . . . . . . 4-9 Connector for TC1784 - Pinout (Part I, Top View) . . . . . . . . . . . . . . . 7-2 Connector for TC1784 - Pinout (Part II, Top View) . . . . . . . . . . . . . . 7-3 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 USB connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Flexray Pinout (SUBD-9 Plug) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 CAN connector pinout (IDC10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 OCDS connector pinout (IDC16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 DAP connector pinout (FTSH10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 Schematic - Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Schematic - External Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Schematic - Config, Clock and CIC61508 . . . . . . . . . . . . . . . . . . . . . 8-4 Schematic - Flexray, CAN and Eeprom . . . . . . . . . . . . . . . . . . . . . . . 8-5 Schematic - MiniWiggler, DAP and ETK . . . . . . . . . . . . . . . . . . . . . . 8-6 Schematic - GPTA, MSC, MLI and ADC . . . . . . . . . . . . . . . . . . . . . . 8-7 Schematic - Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Schematic - Connectors (Plug) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Schematic - Connectors (Socket) . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Component Plot Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11 Component Plot Bottom Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 Dimensioning (mil) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 Dimensioning (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 II-1 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual List of Figures User’s Manual Page II-2 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual List of Tables Table 4-1 Table 4-2 Table 4-3 Table 4-4 Table 4-5 Table 6-1 Table 6-2 Table 6-3 Table 6-4 Table 6-5 Table 6-6 Table 6-7 Table 6-8 Table 6-9 User’s Manual Page User Startup Modes for TC1784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . General optional resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resistors for peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resistors for safety device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resistors for memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety device Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bus Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bus Control Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . III-3 4-1 4-3 4-5 4-7 4-8 6-1 6-1 6-2 6-2 6-2 6-2 6-4 6-4 6-4 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual List of Tables User’s Manual Page III-4 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Introduction 1 Introduction We congratulate you on your purchase of the TriCore Evaluation Board. This kit is a versatile tool, providing quick access to the capabilities of TriCore's powerful architecture. Applications can be developed easily. The Evaluation Board is equipped with a variety of memories and peripherals for connection to the environment. There is also an interface for the On Chip Debugging Features (OCDS1 and DAP). The kit also includes several sets of development tools, which are stored on the included Evaluation Board CD-ROM. The Evaluation Board allows easily the development of TriCore applications with the corresponding tools. Subsequently, the applications can be downloaded and can be tested with the powerful debugger software. This TriBoard Hardware Manual familiarizes you with the TriCore Evaluation Board and guides you through the initial configuration of the TriBoard. For detailed technical information about the TC1784 please refer to the User Manual of the device. User’s Manual 1-1 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Introduction User’s Manual 1-2 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Features 2 TriBoard Features The TriBoard TC1784 is soldered with a the device TC1784 in the BGA292 package. 2.1 – – – – – – – – – – – Summary of Features Infineon’s TC1784 Controller in BGA292 Package FlexRay Transceivers Safety device (optional) High Speed CAN Transceivers USB to UART bridge Crystal 20MHz (default), Oscillator or External Clock USB miniWiggler for easy debugging 8 Low Power Status LEDs 8-DIP switches for configuration access to all pins of controller 100mm x 160mm (EURO-Board) Connectors The TC1784 TriBoard offers a wide variety of connectors: – – – – – – – – Standard power connector USB connector for ASC Interface (ASC0) and miniWiggler 16-pin header for JTAG interface (OCDS) 10-pin header for DAP 2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1) 2 x SUB-D9 Plug connector for FlexRay four 80-pin connectors (male) + four 80-pin connectors (female) with all I/O signals optional ETK connector Components – – – – – – – – – – – – – Infineon’s Next generation micro controller supply TLE 7368 - 3E Three LEDs to validate power supply (5Volt / 3,3 Volt / 1,3 Volt) LED indicating /HDRST (ESR0) active state LED indicating activ miniWiggler LED switched via DAS software 2x FlexRay Transceiver AS8221(AMS) or TJA1080 (NXP) 2 x Infineon’s High Speed CAN-Transceiver TLE 6250 GV33 Infineon’s Safety Device SAK-CIC61508(optional) USB to UART bridge FT2232D (FTDI) SPI eeprom (Atmel) 8 general purpose LEDs Reset switch 8-pin Dip switch User’s Manual 2-1 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Features Zero Ohm Bridges Zero Ohm resistors give the flexibility to configure the systems functionality User’s Manual 2-2 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Features 2.2 Block Diagram XTAL CAN0 TxCAN0 PLL RxCAN0 FLASH 16 Bit TxCAN1 RxCAN1 TC1784 BUS OCDS1 USB B-TYPE USB miniWiggler TXD0 TriCore CPU /CS0 or /CS1 BUS SRAM 16 Bit /CS0 or /CS1 ERAY A SSC0 RXD0 8 LED’s (P5.0 up to P5.7) Serial EEPROM Safety Device SAK-CIC61508 optional POWER SUPPLY WITH SUPERSONIC TLE7368-3E ERAY B FlexRay Transceiver SLSO00 Transceiver ADDRESS and DATA BUS BUS CAN1 Figure 2-1 User’s Manual TriBoard Block Schematic 2-3 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Features 2.3 Placement USB X701 1 X403 A1 OCDS1_CIC BOOTCONFIG ACT OCDS1 L1 CAN0 U202 X302 S601 CAN1 +5V TC1784 +3V3 JP203 X201 RST P302 VDDP_CIC 1 1 RST SYSDISC X202 1 U106 U101 ERAY-B X203 X301 1 P301 ETK X401 RUN U102 1 2 3 4 5 6 7 8 XT201 TriBoard-BGA292 V1.1 DAP S201 1 X402 1 ERAY-A SYSDISB 1 P5.0 P5.1 P5.2 P5.3 P5.4 P5.5 P5.6 P5.7 SYSDISA P401 X704 1 1 1 +1V3 RST_CIC POWER X601 X703 +5,5V...+50V(+40V) Figure 2-2 User’s Manual S202 RESET_CIC X702 1 1 1 1 TriBoard BGA292 V1.1 Placement 2-4 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Information 3 TriBoard Information 3.1 Power Supply The Board has to be connected to a +5,5V to +50V (+40V) DC power supply. The TriBoard generates internally +3.3V, +VDD and +5V. The power consumption is not specified yet but a supply with 6V and 500mA should be sufficient. The pinout for the supply connector is shown in Figure 7-3. There can be used any standard power pack with a connector where the positive line is surrounded by the ground line. Maximum power supply is reduced to +40V if the SAK-CIC61508 option is assembled. +VDD is +1,3V for TC1784. Applying a stable supply voltage causes the power on reset after a short period. The four LED's (+5V, +3.3V, +1,3V) indicate the status of the on board generated voltage (if the LEDs are assembled). A manual reset is executed by pressing the reset button. 3.2 LEDs There are 14 or 19 LEDs on board: – – – – – – – – – – – – 3.3 D501 up to D508 (blue) D604 RST (red) D505 +1V3 (green) D606 +3V3 (green) D607 +5V (green) D402 ACT (green) D401 RUN (red) D204 RST_CIC (red) D205 +VDDP_CIC (green) D201 SYSDISA (red) D202 SYSDISB (red) D203 SYSDISC (red) -> toogle LEDs connected to P5.0 ... P5.7 -> RESET LED indicate the reset state of the board -> +1,3V power supply indication -> +3,3V power supply indication -> +5V power supply indication -> on board MiniWiggler is ACTIV -> Debug RUN mode (switched by DAS Server) -> RESET LED indicate that the CIC is in reset -> +VDDP for CIC power supply indication (+3,3V) -> System Disable A (switched by CIC) -> System Disable B (switched by CIC) -> System Disable C (switched by CIC) Clock There are three possibilities to apply the CPU clock. • • • • Large oscillator circuit (DIP14) Small oscillator circuit (DIP8) Crystal oscillator (default with 20MHz) External clock generator User’s Manual 3-1 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Information The crystal oscillator and the oscillator circuit use the socket XT301. It's possible to apply a 14pol DIP oscillator package or an 8pol DIP oscillator package. OSCILLATOR OSCILLATOR XTAL DIP14 DIP8 Figure 3-1 3.4 GND External Clock Input Clock socket usage (XT301) USB Connector The USB connector is used for connection to a PC. Via the USB it is possible to power the board, using the ASC0 as serial connection via USB and Debugging via DAS. For the pinout of USB socket see Figure 7-4. NOTE: Before connecting the board to the PC, make sure that the actual DAS software is installed on the PC. For actual DAS software please contact your local FAE. The software can also be found on the DAS website 3.4.1 Serial Connection to PC After the first connection of USB to a PC the needed driver will be installed automatically. During this there will be created a new COM port on PC. This COM port can be used to communicate with the board via ASC0 of the device (e.g. bootstrap loader). 3.4.2 MiniWiggler MiniWiggler is a low cost debug tool which allows you access to the JTAG of the device. Make sure that you have the latest DAS release. Debugging is possible via the DAS Server JTAG over USB Chip. Please contact your prefered debug vendor for support of DAS. If you have connected the board to the PC and there runs the DAS server, then a working connection is visible via the green ACTIV LED. The status RUN LED is switched on/off through the DAS Server, depending on the used debugger (client). IMPORTANT: Make sure that there is no or a tristated connection on X401 (OCDS1) and X402 (DAP) if the ACTIV LED is on. User’s Manual 3-2 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Information 3.5 FlexRay The board has 2 SUB-D connectors for FlexRay Communication with up to 10 Mbit/s. For the pinout of the plugs see Figure 7-5. The controller have an E-Ray modul and the transceiver are connected directly to the controller For more information look in the user manual for TC1784 and the schematics Figure 84. 3.6 Serial Eeprom The SSC0 of the TC1784 is connected to a serial EEPROM with a size of 128K (16.384 x 8). As chip select for this EEPROM is used the line SLSO00 (P3.5). To disconnect (disable) the EEPROM remove resistor R353. 3.7 MultiCAN On the board are two CAN transceiver connected to the MultiCAN on TC1784 node 0 and 1. The transceivers are connected to two IDC10 plug. For the pinout of IDC10 plug see Figure 7-6. You can use a IDC female connector with crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9. 3.8 Safety option with SAK-CIC61508 (optional) The safety device is only assembled if the board is with the safety option. The SAK-CIC61508 is connected to the SSC0 of the microcontroller and use the line SLSO01 (P3.6) as chip select. There are 4 LED’s for indication the state of the safety device (SYSDISA, SYSDISB, SYSDISC, VDDP_CIC). Sensor inputs A and B are always connected to the voltages of the Microcontroller. The core voltage of the microcontroller to input A and the port voltage to input B. With switch S202 it is possible to reset the safety device. If JP203 is set, then with S202 is also reset the microcontroller and the safety device is reset by a power on reset of the microcontroller. The safety device can be reprogrammed via JTAG and X203. 3.9 Other peripherals For all other peripherals there are no special plugs on the board. The peripheral signals are available on the different connectors. See “Connector Pin Assignment” on Page 7-1. Note: - SLSO00 is used as chip select for the serial eeprom on board. User’s Manual 3-3 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Information 3.10 Toggle LED’s Port 5 pin 0 up to pin 7 are connected to single LED’s (D501... D508) and can be controlled by Software. This status LED’s are low active. 3.11 Debug System 3.11.1 OCDS1 The OCDS1 signals are connected to the IDC16 plug (X401). They work with the port supply of +3.3V. For pinout of the connector see Figure 7-7. You can connect any debugger to this connector. The signals /BRKIN and /BRKOUT are not connected per default. If you need this signals in the connector then assemble R425 and R424 with a 0R resistor. If you connect a debug hardware make sure that the MiniWiggler (see “MiniWiggler” on Page 3-2) is not activ (ACTIV LED is off) and on the DAP connector (X402) is no hardware connected or the hardware is tristated. If the ACTIV LED is on, then stop the active DAS Server JTAG over USB Chip and/or remove the USB connection to the PC. 3.11.2 DAP On the board is a DAP connector (X402) available. For pinout of this connector see Figure 7-8. You can connect a DAP hardware here. If you use this connector make sure that the MiniWiggler is not activ (ACTIV LED is off) and a connected OCDS1 hardware is disconnected or tristated. User’s Manual 3-4 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual HIGH 1 Figure 4-1 .7 P0 .6 .5 P0 P0 P0 .2 P0 P0 LOW P0 HW Boot Configuration .3 4.1 .1 TriBoard Configuration P0 .0 4 .4 TriBoard Configuration on 2 3 4 5 6 7 8 HW Configuration TC1784 DIP-Switch The picture above shows the definition of the boot HW configuration switch. The meaning of the switches will be described in the following table (Table 4-1). Note: The ON position of the switch is equal to a logical LOW at the dedicated pin. Table 4-1 User Startup Modes for TC1784 Note: The shadowed line indicates the default setting. Note: ’x’ represents the don’t care state. Note: 1 to 8 are the Dip Switch numbers HWCFG[7...0] Type of Boot TC1784 1 2 3 4 5 6 7 8 11XXXXXX Internal Start from Flash X X X X X X O O F F F F 010XXXX0 Bootstrap Loader Mode, Generic Bootloader at O X X X X O O O CAN pins N N F N F 10101XX0 Bootstrap Loader Mode, ASC Bootloader O X X O O O O O N F N F N F F F F 10100XX0 Alternate Boot Mode, ASC Bootloader on fail O X X O O O O O N N N F N F F F User’s Manual 4-1 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Configuration Table 4-1 User Startup Modes for TC1784 Note: The shadowed line indicates the default setting. Note: ’x’ represents the don’t care state. Note: 1 to 8 are the Dip Switch numbers HWCFG[7...0] Type of Boot TC1784 1 2 3 4 5 6 7 8 1011XXXX Alternate Boot Mode, Generic Bootloader at CAN pins on fail X X X X O O O O F F N F F F F all others reserved; don’t use this combination User’s Manual 4-2 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Configuration 4.2 Assembly Options Table 4-2 General optional resistors Component Description R205 XTAL Rserial (default: assembled) R206 XTAL Rparallel (default: not assembled) R423 Connect /BRKOUT with MiniWiggler (default: not assembled) R424 Connect /BRKOUT with OCDS1 connector (default: not assembled) R427 Connect /BRKIN with USR1 of MiniWiggler (default: not assembled R429 Connect /BRKIN with USR1 of DAP (default: not assembled R425 Connect /BRKIN with OCDS1 connector(default: not assembled) R428 Connect /TESTMODE with USR1 of MiniWiggler (default: not assembled R430 Connect /TESTMODE with USR1 of DAP (default: not assembled R426 Connect /TESTMODE with OCDS1 connector(default: not assembled) R432 Connect debug reset with /PORST(default: assembled) R431 Connect debug reset with /HDRST (default:not assembled) R510 Connect +3,3V to all toggle LEDs (default: assembled) R623 Connect reset switch with /PORST(default: assembled) R624 Connect reset switch with /HDRST (default:not assembled) R604 Connect P1.2 with MONSTBY of power device (default: not assembled) R606 Connect P1.3 with WDO of power device (default: not assembled) R609 Connect P1.15 with WDI of power device (default: not assembled) User’s Manual 4-3 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Configuration Note: All resistors are red marked in the following figures CB406 P401 R407 R402 X704 C611 C608 R603 R608 R234 X201 S202 X702 1 1 Location of general optional resistors on Top Side X804 U401 U404 R423 R418 R378 R335 R376 R340 R373 R604 R623 R624 R605 C614 R638 C613 Q601 R620 X802 X803 1 Figure 4-3 User’s Manual C605 Q604 R617 D609 D602 R616 R507 R519 D608 Q603 R627 C609 R606 R628 C606 R619 Q602 R374 R618 R501 R379 R377 R375 R338 Q406 Q404 Q402 Q405 Q403 Q401 U304 R343 CB318 R339 R609 R430 R429 R372 R342 R411 R414 R341 C615 R502 R438 R503 R520 CB403 CB409 R416 R424 C612 R505 CB317 CB613 CB506 R509 CB501 R504 CB504 R508 CB622 CB605 CB604 CB621 CB602 CB502 R506 R319 R336 R437 R320 CB616 CB618 CB619 CB503 CB614 CB626 CB612 CB505 R613 R305 U602 CB627 C616 R625 R333 CB624 CB629 CB628 D603 CB609 CB608 R212 R610 R254 CB631 R207 Y201 R611 R253 R629 R255 CB617 CB610 CB611 CB623CB625 CB202 CB620 CB606 CB607 C201 CB110 CB109 U107 CB201 C202 CB630 R208 R121 CB603 R211 R118 R119 R120 C212 CB206 Y202 R252 CB615 R337 R425 R417 R419 Y401 CB408 R410 R334 R426 U305 R614 R202 R440 R415 R409 R420 CB405 U403 R344 C204 C203 R427 CB407 R205 R204 R219 R220 R221 R222 R223 R224 R225 R226 R203 R428 R412 R435 R421 1 R630 R256 R227 R602 R306 R257 R229 D204 R356 R354 R626 C205 R258 D202 D201 R353 R201 C206 R260 CB205 D205 U202 U203 U306 C610 R641 C209 R259 R213 R231 C208 CB104 R601 R639 R206 R239 JP203 CB208 R355 R436 R422 R240 R230 CB209 CB319 D605 1 C211 CB207 R228 C602 C604 U601 D606 X801 C210 R235 X202 R105 R104 R103 R112 R113 D607 X703 Figure 4-2 D203 CB102 U102 S201 R510 X302 U204 CB103 U104 C601 R233 R232 D507 D506 D505 D504 D503 D501 D508 C207 R115 R621 D604 R640 C607 CB204 R117 U103 R607 X601 D502 R308 R312 U101 R322 R622 CB314 S601 R332 R116 U106 CB601 R328 R329 R331 C304 X203 CB108 R431 CB315 R325 L601 R330 P302 T302 X301 R307 R432 R326 R371 1 2 3 4 5 6 7 8 XT201 R114 C303 D401 T301 R367 CB309 R309 U302 U303 CB316 R327 R515 R516 R517 R513 R514 R209 CB311 R311 R369 CB312 R323 R370 R321 R324 CB313 R511 R433 R313 R366 R317 R316 R315 R314 P301 CB310 R518 R434 R439 R210 R310 R368 X403 X401 R512 X402 R318 D402 CB404 CB402 R408 R401 1 D403 CB203 R405 C401 X701 1 R406 L401 CB401 CB101 U402 C603 R403 R404 1 D601 Location of general optional resistors on Bottom Side 4-4 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Configuration Table 4-3 Resistors for peripherals Component Description R333 Connect P3.12 with RXD of CAN0 transceiver (default: assembled) R339 Connect P3.14 with RXD of CAN1 transceiver (default: assembled) R353 Connect P3.5 (SLSO00) with /CS of Eeprom (default: assembled) R305 Connect P1.4 with EN of Flexray channel A (default: not assembled) R306 Connect P1.6 with STBN of Flexray channel A (default: not assembled) R379 Connect P0.14 with ERRN of Flexray channel A (default: assembled) R319 Connect P1.5 with EN of Flexray channel B (default: not assembled) R320 Connect P1.7 with STBN of Flexray channel B (default: not assembled) R375 Connect P0.15 with ERRN of Flexray channel B (default: assembled) R440 Connect P3.0 with TXD of USB to UART (default: assembled) R505 Connect VAREF0 with VDDM (default: assembled) R507 Connect VAGND0 with VSSM (default: assembled) R508 Connect VFAREF with VDDMF (default: assembled) R509 Connect VFAGND with VSSMF (default: assembled) R519 Connect +5V with VDDM (default: assembled) R520 Connect +3,3V with VDDM (default: not assembled) User’s Manual 4-5 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Configuration Note: All resistors are red marked in the following figures CB406 P401 R407 R402 X704 C608 R603 R234 X201 S202 X702 1 1 Location of peripheral resistors on Top Side X804 U401 U404 R423 R378 R373 R606 R628 R604 R623 R624 R605 Q604 C614 R638 C612 R617 C613 R507 Q601 X803 1 User’s Manual D609 D602 R616 R620 X802 Figure 4-5 D608 Q603 R627 C609 R619 Q602 R374 R618 R501 R375 R376 C606 R609 R519 R379 R377 R335 R334 R424 R340 R343 CB318 R339 R503 R520 R429 R372 R342 R411 R430 R414 R418 R338 Q406 Q404 Q402 Q405 Q403 Q401 U304 R438 CB409 R410 R416 C605 R502 CB506 R509 CB501 R508 R504 CB504 R505 CB317 CB613 R319 R336 R437 R320 CB616 CB618 CB619 CB503 CB614 CB626 CB622 CB605 CB604 CB621 CB602 CB502 R506 CB609 CB608 CB612 CB505 R613 R305 U602 CB627 C616 R333 CB624 CB629 CB628 D603 R254 CB631 R207 Y201 R212 R629 R611 R253 R610 R630 R255 CB617 CB610 CB611 CB623CB625 CB202 CB620 CB606 CB607 C201 CB110 CB109 U107 CB201 C202 CB630 R208 R121 CB603 R211 R118 R119 R120 C212 CB206 Y202 R252 CB615 R419 R625 Y401 CB403 CB408 R341 C615 R425 R337 R426 R417 U305 R614 R202 R440 R415 R409 R420 CB405 U403 R344 C204 C203 R427 CB407 R205 R204 R219 R220 R221 R222 R223 R224 R225 R203 R428 R412 R435 R421 1 R306 C205 R256 D202 D201 R608 R602 R626 R257 R227 D204 R356 R354 R201 C206 R260 R258 D205 U202 R353 C209 CB205 R229 R228 U306 C610 R641 R226 R239 R213 R231 C208 CB104 R601 R639 R206 R259 JP203 CB208 R355 R436 R422 C210 R230 CB209 CB319 D605 1 R240 CB207 U203 C603 C602 C604 U601 D606 X801 C211 R235 X202 R105 R104 R112 R113 D607 X703 Figure 4-4 D203 CB102 U102 S201 R510 U204 CB103 U104 C601 R233 R232 D507 D506 D505 D504 D501 D508 C207 R115 X302 D604 R640 C611 CB204 R117 U103 R607 C607 D503 R308 R312 U101 R322 R622 CB314 S601 R332 R116 U106 CB601 R328 R329 R331 C304 L601 R330 P302 T302 X601 D502 R103 R307 CB315 R325 X203 CB108 R431 R326 R371 1 2 3 4 5 6 7 8 XT201 X301 R366 T301 R367 U303 CB316 R327 R515 R516 R517 R513 R514 R114 C303 D401 R432 U302 CB309 R309 CB311 R311 R369 CB312 R323 R370 R321 R324 CB313 R511 R433 R209 R313 R317 R316 R315 R314 P301 CB310 R518 R434 R439 R210 R310 R368 X403 X401 R512 X402 R318 D402 CB404 CB402 R408 R401 1 D403 CB203 R405 C401 X701 1 R406 L401 CB401 CB101 U402 R621 R403 R404 1 D601 Location of peripheral resistors on Bottom Side 4-6 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Configuration Table 4-4 Resistors for safety device Component Description Voltage divider to adapt VDDP to VAREF of safety device (default: assembled) R239/R240 R252 Connect P3.6 (SLSO01) with /CS of safety device (default: assembled) R253 Connect P3.2 (SSC0) to SCLK of safety device (default: assembled) R254 Connect P2.11 (SSC1) to SCLK of safety device (default: not assembled) R255 Connect P3.4 (SSC0) to MTSR of safety device (default: assembled) R256 Connect P2.12 (SSC1) to MTSR of safety device (default: not assembled) R257 Connect P3.3 (SSC0) to MRST of safety device (default: not assembled) R258 Connect P2.10 (SSC1) to MRST of safety device (default: not assembled) Note: All resistors are red marked in the following figures X801 X804 1 U401 R418 U404 R373 R374 R606 R628 R604 R623 R624 R605 Q604 C614 R638 C613 C612 R617 Q601 X803 1 User’s Manual D609 D602 R616 R507 R620 X802 Figure 4-6 D608 Q603 R627 C606 R619 C609 R609 R519 R375 R376 R618 R501 R379 R377 Q602 R503 R520 R429 R378 R340 R344 R343 R339 CB318 R414 R424 R372 R342 R411 R430 R423 Q406 Q404 Q402 Q405 Q403 Q401 R338 R334 R438 CB409 R410 C605 R502 R504 CB503 CB506 R509 CB501 R508 R505 R613 R319 CB504 CB505 R437 R320 CB616 CB618 CB619 CB408 R336 U304 CB613 CB614 CB603 CB622 CB605 CB604 CB621 CB602 CB502 R506 CB609 CB608 R212 R305 U602 CB627 C616 R333 CB624 R419 R625 CB612 CB629 CB628 D603 R254 R610 R611 R253 R629 R255 CB631 R207 Y201 CB202 CB620 CB606 CB607 C201 CB617 CB610 CB611 CB623CB625 CB626 CB201 C202 CB110 CB109 U107 CB615 CB630 R211 R118 R119 R120 C212 CB206 R257 R208 R121 R630 R256 R252 Y202 C205 R258 C206 R260 CB205 R425 Y401 CB403 R416 R335 R426 R306 R337 R202 R626 R259 CB317 R239 C209 R417 U305 C210 R201 R614 C211 R240 R440 R415 R409 R420 R206 CB405 U403 R341 C615 C204 C203 R427 CB407 R205 R203 R204 R219 R221 R220 R224 R225 R222 R223 R226 R436 R422 R428 R412 R435 R421 1 1 D601 Location of resistors for safety device on Bottom Side 4-7 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Configuration Table 4-5 Resistors for memories Component Description R103 Connect /CS1 to 16-bit SRAMs (default: assembled) R104 Connect /CS0 to 16-bit SRAMs (default: not assembled) R112 Connect /CS0 to 16-bit TSOP Flash (default: assembled) R113 Connect /CS1 to 16-bit TSOP Flash (default: not assembled) R118 Connect /CS0 to NAND Flash (default: not assembled) R119 Connect /CS1 to NAND Flash (default: not assembled) Note: All resistors are red marked in the following figures CB406 P401 R407 R402 X704 U402 User’s Manual D201 D202 R234 D205 R235 X202 R105 R104 R112 R113 R231 CB204 R117 U202 CB103 R230 U203 CB104 D606 CB207 C208 X302 U204 U103 D607 JP203 CB208 R229 R227 R601 U306 C610 R353 R641 R354 R608 X201 R355 CB209 CB319 D605 R228 C603 C602 C604 C608 C207 R115 R621 R622 CB314 S601 CB601 R213 D203 CB102 U102 S201 CB101 R510 U101 R639 R603 R233 R232 D508 D507 D506 D505 D504 D503 D501 R431 U104 R640 X601 C611 D204 R356 S202 R602 X703 C601 Figure 4-7 D502 R308 R116 U106 R607 C607 X203 CB108 D604 U601 R332 R114 C303 R328 R329 R331 R330 C304 1 2 3 4 5 6 7 8 R322 CB315 R325 L601 P302 T302 XT201 R103 R432 R326 R371 R515 R516 R517 R513 R514 X301 R366 R307 U303 CB316 R327 R309 U302 CB309 CB311 R311 R369 CB312 R323 R370 R321 R324 CB313 R511 R433 D401 R317 R316 T301 R367 R315 R314 P301 CB310 R518 R434 R209 R310 R368 X403 X401 R439 R210 R313 R318 D403 D402 R512 X402 X701 1 CB203 CB404 CB402 R401 R408 R405 C401 R312 CB401 1 R406 L401 R403 R404 X702 1 1 Location of memories resistors on Top Side 4-8 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Configuration X801 X804 1 U401 R418 U404 R373 R374 R606 R628 R604 R623 R624 R605 C614 R638 C613 Q601 X803 1 User’s Manual C605 Q604 R617 D609 D602 R616 R507 R620 X802 Figure 4-8 D608 Q603 R627 C606 R619 C609 R609 R519 R375 Q406 Q404 Q402 Q405 Q403 Q401 R338 R334 R423 R376 R618 R501 R379 R377 R340 R343 R339 CB318 R503 R520 R429 R378 R372 R342 R411 R430 R414 R424 C612 R505 R438 CB409 R410 Q602 R502 CB503 CB506 R509 CB501 R508 R504 CB504 CB505 R613 R319 R336 R437 R320 CB616 CB618 CB619 CB408 R344 CB613 CB626 CB614 CB617 CB610 CB611 CB609 CB608 R305 U602 CB627 C616 R333 CB624 R419 R625 CB612 CB629 CB628 D603 R254 CB631 R207 Y201 R212 R629 R611 R253 R610 R255 CB630 CB623CB625 CB202 CB620 CB606 CB607 C201 CB110 CB109 U107 CB201 C202 R121 CB603 R208 CB615 CB622 CB605 CB604 CB621 CB602 CB502 R506 R211 R118 R119 R120 C212 CB206 R257 R252 R630 R256 Y202 C205 R258 C206 R260 CB205 R425 R306 Y401 CB403 R416 R335 R426 R626 R337 R202 U304 R239 R259 CB317 C210 C209 R417 U305 R240 R614 C211 R201 R440 R415 R409 R420 R206 CB405 U403 R341 C615 C204 C203 R427 CB407 R205 R219 R203 R204 R221 R220 R224 R222 R225 R223 R226 R436 R422 R428 R412 R435 R421 1 1 D601 Location of memories resistors on Bottom Side 4-9 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Configuration User’s Manual 4-10 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Software 5 TriBoard Software 5.1 Requirements To install the software from your TriBoard CD you need a PC with Windows 2000, Windows XP, Windows Vista, or Windows 7 5.2 Software Overview The CD does not contain any tool. For the availablity for Demo Versions of the different Tools, please contact the toolvendor directly (e.g. Tasking, Hitex, Lauterbach, GreenHills, HighTec...). To install tools for compiling and debugging use seperat CD’s from Toolvendors. There are also some application notes and software examples. The data sheets of all used parts can be found in the “TriBoard_Components” directory. The manuals for the microcontrollers and the Easy Kit are located in the “Manual” folder. Some useful tools like Acrobat Reader are stored in the “Utilities” directory. The current Errata Sheet can be found in the directory “Errata Sheet”. To make sure you have always the most recent one, please contact your local FAE. Note: For more details see the file ReadMe.txt. 5.3 Software Installation To install tools for the TriCore insert the CD from the Toolvendor and start the file “setup.exe” if the CD is not automatically started. Follow the instructions of the installationprogram. User’s Manual 5-1 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual TriBoard Software User’s Manual 5-2 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Signal Description 6 Signal Description For more information about the signals please see the user manual from TC1784 and/or the schematics of the board. Table 6-1 Power Signals Short Name Description VCC_IN Supply Input (5,5V...50V(40V)) VIN Input voltage of power supply device GND Ground VDD Core Supply Voltage (1,3V) VDDP Port Supply Voltage (3,3V) VDDFL3 Flash Supply Voltage (3,3V) VDDESB Emulation Stand-by SRAM Supply Voltage (1,3V) VDDOSC Main Oscillator Supply Voltage (1,3V) VDDOSC3 Main Oscillator Supply Voltage (3,3V) VSSOSC Main Oscillator Ground VSSM ADC Analog Part Ground VDDM ADC Analog Part Supply Voltage (5V or 3,3V) VSSMF FADC Analog Part Ground VDDMF FADC Analog Part Supply Voltage (3,3V) VDDAF FADC Analog Part Logic Supply Voltage (1,3V) VAGND0 ADC0 Reference Ground VAREF0 ADC0 Reference Voltage (VDDM) VAREF1 ADC1 Reference Voltage (VDDM) VFAGND FADC Reference Ground VFAREF FADC Reference Voltage (VDDMF) VDDP_CIC Port Supply Voltage safety device (3,3V) VAGND_CIC ADC Reference Ground safety device VAREF_CIC ADC Reference Voltage safety device (2,5V) Table 6-2 Reset Signals Short Name Description /PORST Power On Reset /HDRST (ESR0) Hardware Reset User’s Manual 6-1 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Signal Description Table 6-3 Interrupt Signals Short Name Description /NMI (ESR1) Non Maskable Interrupt /RESET_CIC Reset safety device Table 6-4 Clock Signals Short Name Description XTAL1 Crystal Oscillator Input XTAL2 Crystal Oscillator Output XTAL1_CIC Crystal Oscillator Input safety device XTAL2_CIC Crystal Oscillator Output safety device Table 6-5 Debug Signals Short Name Description /TRST Test Reset TCLK Test Clock TMS Test Mode Select TDI Test Data Input TDO Test Data Output /TESTMODE Test Mode Select Input /BRKIN TriCore Breakpoint Input /BRKOUT TriCore Breakpoint Output TCLK_CIC Test Clock safety device TMS_CIC Test Mode Select safety device TDI_CIC Test Data Input safety device TDO_CIC Test Data Outpu safety device MBC_CIC Monitor & Bootstrap loader Control line safety device Table 6-6 Peripheral Signals Short Name Description P3.1 Transmit Data ASC0 P3.0 Receive Data ASC0 P3.8 Transmit Data ASC1 P3.9 Receive Data ASC1 User’s Manual 6-2 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Signal Description Table 6-6 Peripheral Signals P3.2 Clock Line SSC0 P3.3 Master Receive / Slave Transmit SSC0 P3.4 Master Transmit / Slave Receive SSC0 P3.5 Slave Select Output 0 (SSC0) P3.13 CAN Transmitter Output 0 P3.12 CAN Receiver Input 0 P3.15 CAN Transmitter Output 1 P3.14 CAN Receiver Input 1 P2.4 MLI0 receive channel clock P2.5 MLI0 receive channel ready output P2.6 MLI0 receive channel valid input P2.7 MLI0 receive channel data input P2.0 MLI0 transmit channel clock P2.1 MLI0 transmit channel ready input P2.2 MLI0 transmit channel valid output P2.3 MLI0 transmit channel data output P2.11 Clock Line SSC0 P2.10 Master Receive / Slave Transmit SSC0 P2.12 Master Transmit / Slave Receive SSC0 P3.6 Slave Select Output 1 (SSC1) P0 [0...7] General Purpose I/O Port 0 (HWCFG) P0 [8...15] General Purpose I/O Port 0 P1[0...15] General Purpose I/O Port 1 P2[0...13] General Purpose I/O Port 2 P3[0...15] General Purpose I/O Port 3 P4[0...3] General Purpose I/O Port 4 P5[0...7] General Purpose I/O Port 5 (used for LEDs) P5[8...15] General Purpose I/O Port 5 AN[0...35] Analog Inputs P6.1 / FCLP0A MSC0 differential driver clock output positive A P6.0 / FCLN0 MSC0 differential driver clock output negative User’s Manual 6-3 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Signal Description Table 6-6 Peripheral Signals P6.3 / SOP0A MSC0 differential driver serial data output positive A P6.2 / SON0 MSC0 differential driver serial data output negative Table 6-7 Safety device Signals Short Name Description SENA Sensor Input A SENB Sensor Input B SENC Sensor Input C SEND Sensor Input D SCLK_CIC Clock Line SAK-CIC61508 MRST_CIC Master Receive / Slave Transmit SAK-CIC61508 MTSR_CIC Master Transmit / Slave Receive SAK-CIC61508 /CS_CIC Slave Select Input SAK-CIC61508 SYSDISA System Disable Output A SYSDISB System Disable Output B SYSDISC System Disable Output C Table 6-8 Bus Signals Short Name Description D[0...15] Address and Data Bus A[16...20] Address Bus Table 6-9 Bus Control Signals Short Name Description /CS[0...3] Chip Selects /BC[0...1] Byte Controls /RD Read /WR Write /ADV_ALE Address Valid and Address Latch Enable /WAIT Wait Input User’s Manual 6-4 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Connector Pin Assignment 7 Connector Pin Assignment The TriBoard will be shipped with four male (plug) connectors on top layer and four female (socket) connectors on bottom layer. The default connectors are 80-pol. Board to Board connectors from Samtec: http://www.samtec.com Plug: FTSH-140-02-L-DV-ES-A Socket: FLE-140-01-G-DV-A Alternative there can be used the Board to Board System from Robinson Nugent: http://www.robinsonnugent.com Plug: P50L-80P-AS-TGF Socket: P50L-80S-AS-TGF Note: All connectors are pincompatible with the previous versions of TriBoard TC176X. User’s Manual 7-1 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Connector Pin Assignment 7.1 TC1784 Connector / Top View BUS EXPANSION (X701,X801) GND GND AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 /RD /WR Figure 7-1 User’s Manual 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 PERIPHERALS (X702,X802) GND GND A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 GND GND VCC_IN VCC_IN /ADV / ALE /ESR1 GND EN00 / P2.8 SDI0 / P2.13 FCLP0A / P6.1 FCLN0 / P6.0 SOP0A / P6.3 SON0 / P6.2 SLSO00_10 / P3.5 SLSO02_12 / P3.7 SLSO04_14 / P2.8 SLSO06 / P3.8 GND XTAL1 XTAL2 RXD0 / P3.0 TXD0 / P3.1 RXDCAN0 / P3.12 TXDCAN0 / P3.13 SCLK0 / P3.2 MTSR0 / P3.4 MRST0 / P3.3 RXDCAN2 / P9.0 REQ0 / P3.10 REQ2 / P0.6 VDDESB 3V3 3V3 /CS2 /CS1 /CS0 /BC1 /BC0 /ADV / ALE /WAIT /CS3 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 GND GND VCC_IN VCC_IN /ESR0 GND /PORST EN01 / P2.9 SLSI1 / P2.13 SLSO01_11 / P3.6 SLSO03_13 / P2.1 SLSO05_15 / P2.9 SLSO17 / P1.10 GND SYSCLK / P4.3 RXD1 / P3.9 TXD1 / P3.8 RXDCAN1 / P3.14 TXDCAN1 / P3.15 SCLK1 / P2.11 MTSR1 / P2.12 MRST1 / P2.10 TXDCAN2 / P9.1 REQ1 / P3.11 REQ3 / P0.7 GND 3V3 3V3 Connector for TC1784 - Pinout (Part I, Top View) 7-2 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Connector Pin Assignment ADC (X703, X803) VSSM VSSM AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 VSSM VDDM VFAGND VAGND0 VAREF0 VSSM AN32 AN33 AN34 AN35 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 VSSM 61 P10.5 63 P10.6 65 P10.7 67 3V3 69 AD0EMUX0 / P1.12 71 AD0EMUX1 / P1.13 73 AD0EMUX2 / P1.14 75 77 REQ5 / P0.15 79 Figure 7-2 User’s Manual 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 GPTA / MLI (X704,X804) VSSM VSSM AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 VSSMF VDDMF VFAREF VAGND0 VAREF1 VSSM GND GND GPTA0 / P0.0 GPTA1 / P0.1 GPTA2 / P0.2 GPTA3 / P0.3 GPTA4 / P0.4 GPTA5 / P0.5 GPTA6 / P0.6 GPTA7 / P0.7 GPTA8 / P0.8 GPTA9 / P0.9 GPTA10 / P0.10 GPTA11 / P0.11 GPTA12 / P0.12 GPTA13 / P0.13 GPTA14 / P0.14 GPTA15 / P0.15 GPTA16 / P1.0 GPTA17 / P1.1 GPTA18 / P1.2 GPTA19 / P1.3 GPTA20 / P1.4 GPTA21 / P1.5 GPTA22 / P1.6 GPTA23 / P1.7 GPTA24 / P1.8 GPTA25 / P1.9 GPTA26 / P1.10 GPTA27 / P1.11 GPTA28 / P4.0 GPTA29 / P4.1 GPTA30 / P4.2 GPTA31 / P4.3 TCLK1 / P5.11 TREADY1 / P5.10 TVALID1 / P5.9 TDATA1 / P5.8 3V3 3V3 VSSM P10.8 P10.9 P10.10 3V3 P10.11 P10.12 P10.13 REQ4 / P0.14 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 GND GND GPTA32 / P2.0 GPTA33 / P2.1 GPTA34 / P2.2 GPTA35 / P2.3 GPTA36 / P2.4 GPTA37 / P2.5 GPTA38 / P2.6 GPTA39 / P2.7 GPTA40 / P5.0 GPTA41 / P5.1 GPTA42 / P5.2 GPTA43 / P5.3 GPTA44 / P5.4 GPTA45 / P5.5 GPTA46 / P5.6 GPTA47 / P5.7 GPTA82 / P9.2 GPTA83 / P9.3 GPTA84 / P9.4 GPTA85 / P9.5 GPTA86 / P9.6 GPTA87 / P9.7 EMGSTOP / P1.4 P10.0 P10.1 P10.2 P10.3 P10.4 RDATA1 / P5.12 RVALID1 / P5.13 RREADY1/ P5.14 RCLK1 / P5.15 3V3 3V3 Connector for TC1784 - Pinout (Part II, Top View) 7-3 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Connector Pin Assignment 7.2 Power connector pinout +5,5V...50V(40V) GND Figure 7-3 USB connector pinout Figure 7-4 7.4 2 (D-) 1 (Vbus) 3 (D+) 4 (GND) USB connector Pinout Flexray Pinout 6 Figure 7-5 User’s Manual BP 2 BM 1 7 8 3 9 4 5 GND 7.3 Power connector pinout Flexray Pinout (SUBD-9 Plug) 7-4 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Connector Pin Assignment CAN connector pinout 4 6 8 1 0 1 3 5 7 9 Figure 7-6 CAN connector pinout (IDC10) GND /PORST GND GND 6 8 10 12 14 16 3 5 7 9 11 13 15 /BRKIN TCK TDI /TRST 4 1 OCDS connector pinout (IDC16) User’s Manual Key GND GND 8 10 1 3 5 7 9 /RESET 6 USR1_IN 4 USR0_IO 2 DAP0 DAP1 Figure 7-8 GND DAP connector pinout +3V3 7.7 2 TDO TMS Figure 7-7 /BRKOUT OCDS connector pinout +3V3 7.6 GND CANH CANL 2 GND 7.5 DAP connector pinout (FTSH10) 7-5 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Connector Pin Assignment User’s Manual 7-6 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Schematic and Layout 8 Schematic and Layout 8.1 Schematic 8.1.1 Changes on schematic version V1.1 • Change Power Supply to TLE7368-3E User’s Manual 8-1 V 1.1, 2012-02 Figure 8-1 User’s Manual 8-2 A B C D 1 1 /ESR0_/HDRST /PORST PORT[0..10] 2 /TESTMODE JTAG.. /ESR0_/HDRST /PORST MiniWiggler and DAP OCDS.sch PORT[0..10] PORT[0..10] POWER SUPPLY /ESR1_/NMI Supply.sch AN[0..35] GPTA/MSC/MLI/ADC GPTA_ADC.sch 2 3 XTAL[1..2] /TESTMODE JTAG.. PORT[0..10] Clock. Config and Jtag Clk_Cfg_Jtag.sch 3 4 4 A[0..20] AD[0..15] PORT[0..10] /ESR0_/HDRST IFLEX, CAN and Eeprom IFlex_CAN_Eeprom.sch /ESR0_/HDRST BUS..CTRL OnBoard Memories Memories.sch 5 5 6 6 XTAL[1..2] /ESR0_/HDRST PORT[0..10] BUS..CTRL AD[0..15] A[0..20] NC1[0..80] NC2[0..80] AN[0..35] 8 7 8 9 of 9 ATV MC ACE PDA Number: Am Campeon 1-12 Revision: 1.1 D-85579 Neubiberg Date: 10-Jan-2011 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\TriBoard_BGA292.prj Infineon Technologies AG XTAL[1..2] /ESR0_/HDRST /PORST /ESR1_/NMI TriBoard BGA292 Project Sheet: /PORST Connector Socket NC3[0..80] NC4[0..80] Connectf.sch NC4[0..80] NC3[0..80] NC2[0..80] NC1[0..80] A[0..20] AD[0..15] /ESR1_/NMI AN[0..35] Connector Plug BUS..CTRL PORT[0..10] Connectm.sch 7 A B C D TriBoard TC1784 Hardware Manual Schematic and Layout Schematic - Project V 1.1, 2012-02 A B C 1 U16 Y14 R17 U14 T14 Y15 W14 T15 U15 W15 Y17 W17 Y18 W18 Y19 V20 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q VCC GND 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q VCC GND 74LVC573APW 1D 2D 3D 4D 5D 6D 7D 8D OE LE U104 74LVC573APW 1D 2D 3D 4D 5D 6D 7D 8D OE LE U103 GND A8 A9 A10 A11 A12 A13 A14 A15 CB104 100n +3V3 GND A0 A1 A2 A3 A4 A5 A6 A7 CB103 100n BUS INTERFACE 19 18 17 16 15 14 13 12 20 10 19 18 17 16 15 14 13 12 20 10 +3V3 TC1784/TC1387-BGA292 2 P7.0 / AD0 / OUT32 P8.0 / A16 / OUT48 / OUT95 P7.1 / AD1 / OUT33 P8.1 / A17 / OUT49 / OUT96 P7.2 / AD2 / OUT34 P8.2 / A18 / OUT50 / OUT97 P7.3 / AD3 / OUT35 P8.3 / A19 / OUT51 / OUT98 P7.4 / AD4 / OUT36 P8.4 / A20 / OUT52 / OUT99 P7.5 / AD5 / OUT37 P8.5 / CS0 / OUT53 / OUT100 P7.6 / AD6 / OUT38 P8.6 / CS1 / OUT54 / OUT101 P7.7 / AD7 / OUT39 P8.7 / CS2 / OUT55 / OUT102 P7.8 / AD8 / OUT40 P8.8 / CS3 / OUT56 / OUT103 P7.9 / AD9 / OUT41 P8.9 / BC0 / OUT57 / OUT104 P7.10 / AD10 / OUT42 P8.10 / BC1 / OUT58 / OUT105 P7.11 / AD11 / OUT43 P8.11 / RD / OUT59 / OUT106 P7.12 / AD12 / OUT44 P8.12 / RD/WR / OUT60 / OUT107 P7.13 / AD13 / OUT45 P8.13 / ADV / ALE / OUT61 / OUT108 P7.14 / AD14 / OUT46 P8.14 / WAIT / OUT62 / OUT109 P7.15 / AD15 / OUT47 U101F AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 2 3 4 5 6 7 8 9 /ADV_ALE 2 3 4 5 6 7 8 9 1 11 1 11 GND AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 /ADV_ALE GND U19 U20 T19 T20 N20 R20 R19 P20 P19 P17 P16 N19 N17 N16 M17 3 /ADV_ALE A16 A17 A18 A19 A20 /CS0 /CS1 /CS2 /CS3 /BC0 /BC1 /RD /WR /ADV_ALE /WAIT A8 A9 A10 A11 A12 A13 A14 A15 A0 A1 A2 A3 A4 A5 A6 A7 0R 0R_opt R114 10K +3V3 R105 10K /ESR0_/HDRST /RD /WR 0R /CS1 R113 /CS0 R112 /RD /WR /BC0 /BC1 0R_opt /CS1 R103 /CS0 R104 +3V3 +3V3 4 4 10K /ESR0_/HDRST /CSBFL /RD /WR R115 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 /CSRAM /RD /WR /BC0 /BC1 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 12 26 28 11 47 25 24 23 22 21 20 19 18 8 7 6 5 4 3 2 1 48 17 16 9 6 41 17 39 40 1 2 3 4 5 18 19 20 21 43 44 24 25 26 27 42 22 23 28 VSS VSS VCC VCC DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 12 34 VSS VSS VCC RY/BY NC/WP NC/VPP DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15/A-1 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 5 +3V3 FLASH 1Mx16 3,3V 70ns RESET CE OE WE BYTE A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 U106 10K R120 27 46 37 15 14 13 30 32 34 36 39 41 43 45 29 31 33 35 38 40 42 44 +3V3 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 29 30 31 32 35 36 37 38 11 33 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 7 8 9 10 13 14 15 16 SRAM 256Kx16 3,3V 12ns CS OE WE LB UB A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 U102 5 R118 0R_opt GND +3V3 /CSCFL R119 0R_opt 0R CB108 100n +3V3 10K R117 R116 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 GND CB102 100n 3 CB101 100n 2 /CS0 8-3 /CS1 User’s Manual 6 6 17 16 9 8 18 A16 A17 /CSCFL /RD /WR +3V3 R121 R/B VSS VSS VSS VSS PRE/VSS VCC VCC 13 36 25 48 38 12 37 7 NANDFLASH4GX16_OPT WP CE RE WE ALE CLE I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 U107 /WAIT +3V3 GND Infineon Technologies AG BUS..CTRL A[0..20] AD[0..15] 8 7 8 1 of 9 ATV MC ACE PDA Number: Am Campeon 1-12 Revision: 1.1 D-85579 Neubiberg Date: 10-Jan-2011 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\Memories.sch Sheet: TriBoard BGA292 External Memories 19 27 29 31 33 41 43 45 47 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 10K 26 28 30 32 40 42 44 46 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 7 CB110 100n Figure 8-2 CB109 100n D 1 A B C D TriBoard TC1784 Hardware Manual Schematic and Layout Schematic - External Memories V 1.1, 2012-02 A17 A16 A B C D 1 TDO_CIC SYSDISB SYSDISA VDDP_CIC GND VAGND_CIC VAREF_CIC SEND P1_0_CIC P1_1_CIC P1_5_CIC /CS_CIC P3_7_CIC SYSDISB SYSDISA P3_2_CIC P3_3_CIC P3_4_CIC P3_5_CIC /RESET_CIC P2_3_CIC P2_4_CIC P2_5_CIC P2_6_CIC P1_6_CIC P1_7_CIC TMS_CIC TCK_CIC TDO_CIC TDI_CIC SENA SENB SENC R227 10K MBC_CIC SCLK_CIC MTSR_CIC MRST_CIC XTAL2_CIC XTAL1_CIC GND VDDC_CIC CON1X19_opt 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 X202 620R R235 620R R234 620R R233 GND C212 10nF_opt SEND GND VDDP_CIC LS T67K CON1X19_opt 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 X201 GND D203 LS T67K D202 LS T67K D201 SENC C211 10nF_opt 1 11 12 13 14 2 3 4 MBC_CIC TMS_CIC TCK_CIC TDO_CIC TDI_CIC SCLK_CIC MTSR_CIC MRST_CIC VAGND_CIC 2 CB206 100n 24 25 27 28 29 9 10 38 /RESET_CIC P1_0_CIC P1_1_CIC P1_5_CIC P1_6_CIC P1_7_CIC VAREF_CIC 5 SAK-CIC61508 VAGND VAREF P1.0 / RXD_0 P1.1 / TXD_0 P1.5 P1.6 P1.7 P0.3 / SCLK_1 P0.4 / MTSR_1 P0.5 / MRST_1 MBC TMS P0.0 / TCK_0 P0.2 / TDO_0 P0.1 / TDI_0 RESET XTAL2 XTAL1 VSSP VDDC_CIC P2.7 / AN7 P2.6 / AN6 P2.5 / AN5 P2.4 / AN4 P2.3 / AN3 P2.2 / AN2 P2.1 / AN1 P2.0 / AN0 P3.7 P3.6 P3.5 P3.4 P3.3 P3.2 P3.1 P3.0 VSSC VDDC 2K 3 10 8 GND GND MRST_CIC 1 /RESET_CIC MRST_CIC MTSR_CIC SCLK_CIC /CS_CIC OUT GND OUT 0R 3 6 4 1 3 5 7 9 11 13 15 VSSOSC C208 22μF/10V GND R230 GND opt C207 1uF VAREF_CIC GND R255 0R_opt 1 0R_opt R258 0R_opt RESET JP203 0R R257 0R 0R R254 R256 R253 0R R252 OCDS1_CIC 2 TMS VCC TDO GND CPUCLOCK GND TDI PORST TRST BRKOUT TCK GND BRKIN OCDSE N.C. KEY X203 Y201 XTAL2 C201 opt opt 1 R206 opt XTAL1 VDDP_CIC 3 VAGND_CIC R231 REF192GS GND SLEEP V+ U204 GND 4 2 IN 0R 0R R205 50R_opt R204 R203 C204 33pF GND U203 TLE4274DV33 MBC_CIC R232 1K TCK_CIC TDI_CIC TMS_CIC TDO_CIC CB205 220n GND CB207 100n VDDP_CIC GND CB209 100n VIN 4 GND C203 33pF ONLY ON REQUEST P3_7_CIC GND /CS_CIC P3_5_CIC P3_4_CIC P3_3_CIC P3_2_CIC SYSDISA SYSDISB SEND P2_6_CIC P2_5_CIC P2_4_CIC P2_3_CIC SENC SENB SENA XTAL2 XTAL1 /TESTMODE Crystal 20MHz VCC VCC GND OE OE XT201 CB204 100n VDDC_CIC GND VDDP_CIC R260 26 23 22 21 20 17 16 15 31 30 37 36 35 34 33 32 7 8 19 18 GND 11 14 7 1 4 XTAL[1..2] /TESTMODE 3 CB203 100n +3V3 GND VDDP 22pF_opt C206 CSTCR6M00G U202 22pF_opt C205 GND VDDP_CIC Y202 2 GND 6 S202 620R R228 RESET_CIC CB208 100n R229 10K XTAL2_CIC XTAL1_CIC XTAL2_CIC XTAL1_CIC /RESET_CIC D204 GND R239 1K6 R240 1K VDDP LS T67K VDDP_CIC GND C210 10nF C209 10nF GND /RESET_CIC SENB SENA R259 0R VDDCORE 2 1 8-4 3 User’s Manual GND Figure 8-3 2 1 C202 opt 5 /PORST P2_10 P3_3 P2_12 P3_4 P2_11 P3_2 P3_6 5 VDDP_CIC 2 4 GND 6 8 /RESET_CIC MBC_CIC 10 12 GND 14 16 GND D205 LP T67K R213 680R VSSOSC 2 R207 opt XTAL2 XTAL1 GND R202 opt R201 10K +3V3 E14 D15 G4 B8 B18 P3_10 E15 P3_11 E13 P2_10 P3_3 JTAG / DAP / OCDS1 CLOCK & TESTMODE TC1784 P0_7 P0_6 P0_5 P0_4 P0_3 P0_2 P0_1 P0_0 6 P3.10 / OUT92 / REQ0 P3.11 / OUT93 / REQ1 P2.10 / IN10 / OUT0 / MRST1A P10_0 P10_1 P10_2 P10_3 680R R226 680R R224 680R R222 680R R220 P3.1 / OUT85 / TXD0A P3.8 / SLSO06 / OUT90 / TXD1 P3.4 / OUT88 / MTSR0 P3.2 / OUT86 / SCLK0 P9.1 / OUT81 / TXDCAN2 P3.15 / OUT97 / TXDCAN1 / TXD1 P3.13 / OUT95 / TXDCAN0 / TXD0 +1V3 VSSOSC /TRST R211 8 GND +3V3 JTAG.. GND R210 10K_opt R209 10K +3V3 0R CB201 0R 330n R208 VDDOSC3 D19 C20 B17 A7 A8 A17 A18 H4 A16 A15 A19 D16 P3_5 P3_6 P3_7 P2_12 P2_11 P3_4 P3_2 P9_1 P3_15 P3_13 P3_8 P3_1 CFG0 CFG1 CFG2 CFG3 CFG4 CFG5 CFG6 CFG7 1 2 3 4 5 6 7 8 Infineon Technologies AG GND 16 15 14 13 12 11 10 9 7 8 2 of 9 ATV MC ACE PDA Number: Am Campeon 1-12 Revision: 1.1 D-85579 Neubiberg Date: 10-Jan-2011 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\Clk_Cfg_Jtag.sch Sheet: 1 PORT[0..9] DIPSW-8 S201 Switch ON means the corresponding signal is low. Switch OFF means the corresponding signal is high. TriBoard BGA292 Clock, Config, Jtag and CIC61508 P3.5 / SLSO00_10 P3.6 / SLSO01_11 P3.7 / SLSI01 / OUT89 / SLSO02_12 P2.12 / IN12 / OUT2 / MTSR1A / SOP0B P2.11 / IN11 / OUT1 / SCLK1A / FCLP0B P3.14 / OUT96 / RXDCAN1 / RXD1B P3.3 / OUT87 / MRST0 680R R225 680R R223 680R R221 680R R219 ASC / CAN / SSC / EXT. REQ P9.0 / OUT80 / RXDCAN2 D6 E6 D5 B5 VSSOSC G20 TDO K20 R212 CB202 0R 330n VDDOSC K19 H20 7 NOTE: S201 is for boot configuration (about configuration see the manual of assembled device). P3.12 / OUT94 / RXDCAN0 / RXD0B P3.9 / OUT91 / RXD1A TC1784 VSSOSC VDDOSC VDDOSC3 TRST TDO / DAP2 / BRKIN / BRKOUT TCK / DAP0 TMS / DAP1 P10.0 / EVTO0 TDI / BRKIN / BRKOUT P10.1 / EVTO1 P10.2 / EVTO2 P1.15 / BRKIN / BRKOUT P10.3 / EVTO3 XTAL2 XTAL1 TESTMODE U101B P3.0 / OUT84 / RXD0A U101C P1_15 P3_14 B16 P9_0 G19 F20 H17 H19 J19 J20 F19 P1_15 F16 P3_12 B15 P3_9 P3_0 /TRST TCK TMS TDI XTAL2 XTAL1 /TESTMODE 6 A B C D TriBoard TC1784 Hardware Manual Schematic and Layout Schematic - Config, Clock and CIC61508 V 1.1, 2012-02 A B C 1 +3V3 2 10K R356 10K R355 GND CB319 100n +3V3 7 3 8 4 CS SCK SI SO AT25128N-10SI2.7 HOLD WP VCC GND U306 1 6 5 2 3 0R R354 100K R353 +3V3 P3_5 P3_2 P3_4 P3_3 4 0R 0R_opt R375 ERRNB P0_15 ENB RXDB TXENB TXDB P1_7 0R R319 0R R372 0R R373 R374 0R_opt R320 STBNB P1_5 P0_9 P0_13 P0_11 0R 0R_opt R379 ERRNA P0_14 ENA RXDA TXENA TXDA P1_6 0R R305 0R R378 0R R377 R376 0R_opt R306 STBNA P1_4 P0_8 P0_12 P0_10 P3_15 P3_14 P3_13 P3_12 4 5 R313 opt INH1A INH2A WAKEA 9 3 4K7 R322 9 3 5 6 7 8 2 1 15 GND R327 opt INH1B INH2B WAKEB 2 1 15 4K7 STBNB 13 ERRNB RXENB 12 R323 +3V3 TXDB TXENB RXDB BGEB ENB R321 4K7 +3V3 GND R326 opt 4K7 R308 5 6 7 8 4K7 STBNA 13 ERRNA RXENA 12 R309 +3V3 GND R325 opt GND R324 opt GND GND GND TXDA TXENA RXDA BGEA ENA R307 4K7 +3V3 R312 opt 0R R339 0R R333 GND R311 opt GND R310 opt GND 5 GND GND AS8221 6 INH1 INH2 WAKE ERRN RXEN STBN EN TXD TXDEN RXD BGE U303 AS8221 INH1 INH2 WAKE ERRN RXEN STBN EN TXD TXDEN RXD BGE U302 100n CB318 +5V 100n CB317 +5V 6 1 2 3 4 1 2 3 4 GND VBAT VDD VIO NU / VBUF BM BP NU / TRXD1 NU / TRXD0 GND VBAT VDD VIO NU / VBUF BM BP NU / TRXD1 NU / TRXD0 0R R340 6 8 5 7 6 8 5 7 R341 0R +3V3 R335 0R +3V3 R337 0R R342 0R 120R R344 R343 0R VIN 0R GND VIN 0R GND 3 2 +5V GND +3V3 +5V GND 0R R368 GND +5V GND opt T302 R328 3 2 +3V3 GND +5V C304 10nF R332 0R GND R330 51R ONLY WITH NXP TJA1080 GND 0R R371 opt B82790-C0513-N201 R329 4 1 GND Infineon Technologies AG GND GND X2 5 9 4 8 3 7 2 6 1 X1 X2 5 9 4 8 3 7 2 6 1 X1 GND GND CHANNELB P302 CHANNELA P301 8 7 8 3 of 9 ATV MC ACE PDA Number: Am Campeon 1-12 Revision: 1.1 D-85579 Neubiberg Date: 10-Jan-2011 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\IFlex_CAN_Eeprom.sch Sheet: R331 51R C303 10nF R317 51R 2 4 6 8 10 2 4 6 8 10 R318 0R ONLY WITH NXP TJA1080 GND opt R316 51R CAN1 1 3 5 7 9 X302 CAN0 1 3 5 7 9 X301 TriBoard BGA292 IFlex, CAN and Eeprom GND 16 14 19 4 20 17 BMB 18 BPB 10 11 0R R370 R369 opt T301 R314 B82790-C0513-N201 R315 4 1 GND ONLY WITH NXP TJA1080 GND 16 14 19 4 20 17 BMA 18 BPA 10 11 0R R367 R366 7 R336 0R 120R R338 ONLY WITH NXP TJA1080 TLE6250GV33 TXD CANL GND INH VCC RM RXD CANH U305 0R R334 TLE6250GV33 TXD CANL GND INH VCC RM RXD CANH U304 CB309 100n CB313 100n D PORT[0..10] 3 CB311 100n 2 CB310 100n CB314 100n 8-5 CB312 100n User’s Manual CB315 100n Figure 8-4 CB316 100n 1 A B C D TriBoard TC1784 Hardware Manual Schematic and Layout Schematic - Flexray, CAN and Eeprom V 1.1, 2012-02 8-6 A B C D 1 PORT[0..10] R405 10K VDD_USB GND CB406 100n VDD_USB 1 2 3 4 7 4 8 5 ORG CS CLK D GND 10n CB401 93LC46B-I/SN DNC Q VCC GND U402 USB Connector P401 L401 6 1 2 3 2 2K2 opt R406 R407 33n CB405 2 P1_15 P1_15 P1_15 P1_15 P1_0 PWREN TEST EECS EESK EEDATA RESET XTOUT XTIN RSTOUT USBDP USBDM 3V3OUT 100n CB402 100n P1_0 41 47 48 1 2 4 44 43 5 7 8 6 GND 0R_opt R429 0R_opt R427 0R_opt R425 0R_opt R424 0R_opt R423 3 0R_opt /TESTMODE /TESTMODE /TESTMODE +3V3 2 4 GND 6 8 /DBGRST /BRKOUT 10 12 GND 14 16 USR1_DAP R430 BDBUS0 BDBUS1 40 39 38 37 36 35 33 32 1K R414 OCDS1 4 /TESTMODE VCC TMS GND TDO GND CPUCLOCK PORST TDI BRKOUT TRST GND TCK OCDSE BRKIN KEY N.C. X401 VDD_USB 10K D401 LS T67K R411 1K5 VDD_USB VDD_USB R408 ACBUS0 ACBUS1 ACBUS2 ACBUS3 15 13 12 11 10 30 29 28 27 26 ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 24 23 22 21 20 19 17 16 FT2232D BCBUS0 BCBUS1 BCBUS2 BCBUS3 SI/WUB BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 SI/WUA 0R_opt R428 USR1 GND ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 100n U401 GND CB404 0R_opt R426 /BRKIN USR2 GND 470R R401 100n CB409 4 10K R418 /BRKIN /TESTMODE 1 3 5 7 9 11 13 15 BDBUS1 2 VDD_USB BDBUS0 2 Q403 BSS138N R416 10K VDD_USB 2 Q406 BSS138N 5 2 10K R419 Q404 BSS138N USR1_DAP USR1 TDI /TRST TCK TMS TDO /DBGRST USR2 Q405 BSS138N 33 33 Q402 BSS138N P3_1 P1_3 /ESR0_/HDRST /PORST /PORST G G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 /PORST 1 3 5 7 9 6 /TRST TCK TDI TMS /TRST USR1 /DBGRST /DBGRST /PORST DAI2 DAI1 GND DAI4 DAI3 /ESR0_/HDRST /BRKOUT_ETK ETK_CON_opt B1 A1 B2 A2 B3 A3 B4 A4 B5 A5 B6 A6 B7 A7 B8 A8 B9 A9 B10 A10 B11 A11 B12 A12 B13 A13 X403 TDO VDDESB /DBGRST VDDP TMS TCK TDI 22R_opt R439 Infineon Technologies AG JTAG.. 8 7 8 4 of 9 ATV MC ACE PDA Number: Am Campeon 1-12 Revision: 1.1 D-85579 Neubiberg Date: 10-Jan-2011 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\OCDS.sch Sheet: TriBoard BGA292 miniWiggler, DAP and ETK DAP2WIRE VREF DAP1 GND DAP0 GND USER0_IO KEY USER1_IN GND RESET TMS TCK TDO USR1_DAP /DBGRST USR2 2 4 6 8 10 1 TDO GND BAT54 D403 USR2 GND R422 opt 3 7 TDO X402 GND R421 opt GND TCK TDI TMS USR0 /TRST /RESET USR1 USR8 CB407 100n +3V3 /BRKIN_ETK /ESR0_/HDRST 0R R432 0R_opt R431 22R_opt 22R_opt R438 R437 22R_opt 22R_opt R436 22R_opt R435 0R_opt R434 R433 GND +3V3 2 4 6 8 11 13 15 17 1 19 18 16 14 12 9 7 5 3 20 10 VDDESB 6 SN74AHCT244PW 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 VCC GND U404 P1_14 P1_2 P1_1 P1_0 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 VCC GND SN74AHC244PW 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 G G U403 R412 680R D402 LP T67K +3V3 P1_15 18 16 14 12 9 7 5 3 20 10 2 4 6 8 11 13 15 17 1 19 /ESR0_/HDRST R440 0R R420 1K +3V3 GND CB408 100n 2 R409 10K +3V3 R415 10K +3V3 VDD_USB 33 +3V3 Q401 BSS138N R417 10K +3V3 ACBUS3 ADBUS2 ADBUS0 ADBUS1 ADBUS3 ADBUS6 ACBUS0 ACBUS1 ACBUS2 ADBUS5 ADBUS4 2 R410 10K VDD_USB 5 1 CB403 3 1 GND P1_0 GND VDD_USB Y401 CSTCR6M00G 1K5 27R R404 27R R403 R402 GND GND C401 10μ/6V VDD_USB GND GND 2 VDD_USB MMZ1608R300A 1 3 3 42 VCC VCC 46 AVCC 14 31 VCCIOA VCCIOB GND GND GND GND 9 18 25 34 AGND 45 1 1 1 1 User’s Manual P3_1 Figure 8-5 P3_0 1 A B C D TriBoard TC1784 Hardware Manual Schematic and Layout Schematic - MiniWiggler, DAP and ETK V 1.1, 2012-02 Figure 8-6 User’s Manual 8-7 A B C D D9 J5 J4 K4 K5 L4 L5 A5 B4 A4 B3 A3 A2 C1 D2 E4 F5 P2_13 P9_2 P9_3 P9_4 P9_5 P9_6 P9_7 P10_4 P10_5 P10_6 P10_7 P10_8 P10_9 P10_10 P10_11 P10_12 P10_13 1 E12 D12 D11 E11 E9 E8 D8 E7 A14 B14 A13 B13 A12 B12 D7 B7 F17 E17 M16 K16 J16 H16 G16 G17 P0_0 P0_1 P0_2 P0_3 P0_4 P0_5 P0_6 P0_7 P0_8 P0_9 P0_10 P0_11 P0_12 P0_13 P0_14 P0_15 P1_0 P1_1 P1_2 P1_3 P1_4 P1_5 P1_6 P1_7 1 GPTA / LTCA / HWCFG / SSC / MLI / MSC 3 TC1784 2 P2.13 / IN13 / OUT3 / SLSI11 / SDI0 P9.2 / OUT82 P9.3 / OUT83 P9.4 / OUT84 P9.5 / OUT85 P9.6 / OUT86 P9.7 / OUT87 P10.4 P10.5 P10.6 P10.7 P10.8 P10.9 P10.10 P10.11 P10.12 P10.13 3 P6.1 / IN15 / OUT5 / OUT81 / FCLP0A P6.0 / IN14 / OUT4 / OUT80 / FCLN0 P6.3 / IN25 / OUT7 / OUT83 / SOP0A P6.2 / IN24 / OUT6 / OUT82 / SON0 P2.8 / SLSO04 / SLSO14 / EN00 P2.9 / SLSO05 / SLSO15 / EN01 P5.8 / RDATA0B / OUT89 P5.9 / RVALID0B / OUT90 P5.10 / RREADY0B / OUT91 P5.11 / RCLK0B / OUT92 P5.12 / TDATA0 / SLSO07 / OUT93 P5.13 / TVALID0B / SLSO16 P5.14 / TREADY0B / OUT94 P5.15 / TCLK0 / OUT95 P0.0 / IN0 / HWCFG0 / OUT0 / OUT56 P1.8 / IN24 / IN48 / MTSR1B / OUT24 / OUT48 P0.1 / IN1 / HWCFG1 / OUT1 / OUT57 P1.9 / IN25 / IN49 / MRST1B / OUT25 / OUT49 P0.2 / IN2 / HWCFG2 / OUT2 / OUT58 P1.10 / IN26 / IN50 / OUT26 / OUT50 / SLSO17 P0.3 / IN3 / HWCFG3 / OUT3 / OUT59 P1.11 / IN27 / IN51 / SCLK1B / OUT27 / OUT51 P0.4 / IN4 / HWCFG4 / OUT4 / OUT60 P4.0 / IN28 / IN52 / OUT28 / OUT52 P0.5 / IN5 / HWCFG5 / OUT5 / OUT61 P4.1 / IN29 / IN53 / OUT29 / OUT53 P0.6 / IN6 / HWCFG6 / REQ2 / OUT6 / OUT62 P4.2 / IN30 / IN54 / OUT30 / OUT54 / EXTCLK1 P0.7 / IN7 / HWCFG7 / REQ3 / OUT7 / OUT63 P4.3 / IN31 / IN55 / OUT31 / OUT55 / EXTCLK0 P0.8 / IN8 / RXDA0 / OUT8 / OUT64 P2.0 / IN32 / OUT32 / OUT28 / TCLK0 P0.9 / IN9 / RXDB0 / OUT9 / OUT65P2.1 / IN33 / TREADY0A / OUT33 / SLSO03 / SLSO13 P0.10 / IN10 / OUT10 / TXDA0 P2.2 / IN34 / OUT34 / OUT29 / TVALID0A P0.11 / IN11 / OUT11 / TXDB0 P2.3 / IN35 / OUT35 / OUT30 / TDATA0 P0.12 / IN12 / OUT12 / TXENA P2.4 / IN36 / RCLK0A / OUT36 / OUT31 P0.13 / IN13 / OUT13 / TXENB P2.5 / IN37 / OUT37 / OUT110 / RREADY0A P0.14 / IN14 / REQ4 / OUT14 / OUT70 P2.6 / IN38 / RVALID0A / OUT38 / OUT111 P0.15 / IN15 / REQ5 / OUT15 / OUT71 P2.7 / IN39 / RDATA0A / OUT39 P1.0 / IN16 / OUT16 / OUT72 / BRKIN / BRKOUT P5.0 / IN26 / IN40 / OUT8 / OUT40 P1.1 / IN17 / OUT17 / OUT73 P5.1 / IN27 / IN41 / OUT9 / OUT41 P1.2 / IN18 / OUT18 / OUT74 P5.2 / IN28 / IN42 / OUT10 / OUT42 P1.3 / IN19 / OUT19 / OUT75 P5.3 / IN43 / OUT11 / OUT43 P1.4 / IN20 / EMGSTOP / OUT20 / OUT76 P5.4 / IN30 / IN44 / OUT12 / OUT44 P1.5 / IN21 / OUT21 / OUT77 P5.5 / IN31 / IN45 / OUT13 / OUT45 P1.6 / IN22 / OUT22 / OUT78 P5.6 / IN32 / IN46 / OUT14 / OUT46 P1.7 / IN23 / OUT23 / OUT79 P5.7 / IN47 / OUT15 / OUT47 U101D 2 P5_8 P5_9 P5_10 P5_11 P5_12 P5_13 P5_14 P5_15 P6_1 P6_0 P6_3 P6_2 P2_8 P2_9 B10 A10 B9 A9 E10 D10 P1_8 P1_9 P1_10 P1_11 P4_0 P4_1 P4_2 P4_3 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7 H2 J2 J1 K2 K1 L2 L1 H1 L17 L19 L16 L20 T13 U13 W13 Y13 Y11 W11 U11 T11 Y12 W12 U12 T12 D1 E2 F4 G5 H5 E1 F1 F2 4 P5_7 P5_6 P5_5 P5_4 P5_3 P5_2 P5_1 P5_0 4 100R R516 100R R517 100R R518 D505 LB T673 D506 LB T673 D507 LB T673 D508 LB T673 100R 100R R515 D504 LB T673 LB T673 100R R514 0R 100R R512 100R R513 R510 R511 D503 LB T673 D502 LB T673 D501 AN[0..35] +3V3 5 5 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 AN32 AN33 AN34 AN35 Y9 W9 T9 U8 Y8 W8 T8 T2 U7 Y6 Y5 Y4 Y3 Y2 W2 U5 W3 W5 W4 W6 W1 U4 V2 V1 T5 T4 U2 U1 T1 R5 R4 R2 R1 P5 P4 P1 ADC / FADC TC1784 6 N5 N4 T6 U6 T7 P2 N1 N2 W7 Y7 T10 U10 U9 0R R504 0R VFAGND 0R 0R CB506 100n R509 VSSMF VAGND0 VFAREF VDDMF R508 0R VDDM +3V3 GND R506 CB505 100n VAREF1 VSSMF CB503 10n VDDMF VSSM CB502 R501 10n VDDM P1_12 P1_13 P1_14 7 VAGND0 Infineon Technologies AG VSSM VDDM GND +1V3 PORT[0..10] 0R 8 7 8 5 of 9 ATV MC ACE PDA Number: Am Campeon 1-12 Revision: 1.1 D-85579 Neubiberg Date: 10-Jan-2011 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\GPTA_ADC.sch Sheet: R505 0R 0R R503 R502 +3V3 +5V 0R CB504 100n R507 VAREF0 VSSMF CB501 10n VDDAF 0R_opt R520 0R R519 TriBoard BGA292 GPTA, MSC, MLI and ADC AN0 P1.12 / IN16 / OUT16 / AD0EMUX0 AN1 P1.13 / IN17 / OUT17 / AD0EMUX1 AN2 P1.14 / IN18 / OUT18 / AD0EMUX2 AN3 AN4 AN5 AN6 VDDM AN7 AN8 AN9 VSSM AN10 AN11 AN12 AN13 VDDAF AN14 AN15 AN16 VDDMF AN17 AN18 AN19 VSSAF / VSSMF AN20 AN21 AN22 AN23 VAREF0 AN24 VAREF1 AN25 AN26 AN27 VAGND0 AN28 / FAIN2P AN29 / FAIN2N AN30 / FAIN3P AN31 / FAIN3N VFAREF AN32 / FAIN0P AN33 / FAIN0N AN34 / FAIN1P VFAGND AN35 / FAIN1N U101E 6 A B C D TriBoard TC1784 Hardware Manual Schematic and Layout Schematic - GPTA, MSC, MLI and ADC V 1.1, 2012-02 A B C D GND C613 4μ7/10V GND C614 1μ/6V Q_STBY GND BC848C /PORST 82K R616 1 /ESR1_/NMI SS12 /ESR1_/NMI RESET R620 4K7 +3V3 R626 4K7 +3V3 GND 2 4K7 GND R622 10K GND_A GND_A GND_A GND_A GND_P WDI EN_uC EN_IGN SEL_LDO2 CCP C2- C2+ C1- C1+ IN IN IN C615 4μ7/10V 1 GND SW SW BST 0R_opt R609 3 R623 0R RT RO_1 RO_2 WDO Q_T1 Q_T2 FB_EXT DRV_EXT Q_LDO2 Q_LDO1 FB/L_IN IN_LDO2 Q602 BC848C TLE7368-3E GND 1 18 19 36 17 24 9 10 23 GND GND_A 10K 10K R602 R621 D607 LP T67K R619 1K5 +5V 220n +3V3 +3V3 R601 VIN 15 C602 100n 12 14 20 21 22 C603 100n 13 C604 16 CB601 100n VIN GND C601 47μ/50V S601 R625 1K +3V3 +3V3 GND D606 LP T67K R618 680R +3V3 /ESR0_/HDRST /PORST GND D605 LP T67K R617 620R +3V3 Q604 1 SS12 C611 22μ/10V +1V3 +1V3 D608 +3V3 D609 +5V GND C612 4μ7/10V Q_T2 Q_T1 C610 22μ/10V GND C609 22μ/10V +3V3 GND +5V GND /ESR0_/HDRST +1V3 2 2 X601 POWER VCC_IN D601 1 5,5V..50V 1 MBRS360T3 WDI 2 0R Q_T1 Q_T2 C608 1n2 /ESR0_/HDRST R624 0R_opt 1 R627 10K 1 R641 0R 0R GND 4 R610 GND VDDP +1V3 GND P1_15 P1_3 D604 LS T67K R628 120R Q603 BC858C +3V3 +3V3 4K7_opt 0R GND 0R C607 4μ7/10V R640 C606 47μ/10V GND 0R_opt +3V3 R608 R606 Q601 BDP949 VSW 4 P1_2 VSW R607 R605 10K +3V3 /PORST GND GND +5V L601 47μ/3A D602 MBRS340T3 0R +3V3 R639 R638 C605 680n 0R_opt R603 10K R604 +3V3 25 WDO RO_5V 3 4 7 8 31 32 6 30 29 5 28 26 27 33 35 /PORST IN_STBY Q_STBY SEL_STBY MON_STBY /PORST Q_STBY /ESR0_/HDRST 3 2 GND GND GND GND GND 3 GND CB627 100n_opt VIN GND GND IN U602 TLE4284DV_opt GND +1V3 GND /PORST /ESR0_/HDRST /ESR1_/NMI 5 GND 100n 0R E20 D20 E19 B1 B6 B11 B20 C2 C19 G2 M2 M19 W10 W16 GND VDDCORE 100n 100n CB609 CB607 CB608 100n 100n 100n 100n 100n 100n CB606 CB605 CB604 CB603 CB602 CB623 100n 100n CB624 CB625 GND C616 10μ/10V_opt VDDESB 100n 2 CB626 R611 OUT ONLY WITH TC178XED AND ON REQUEST PORT[0..10] 5 ADJ / GND U601 3 6 W20 V19 T17 R16 P13 P8 N14 N7 H14 H7 G13 G8 PORST ESR0 ESR1 VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD 3 2 GND CB628 47n VDDESB POWER GND CB629 47n ONLY WITH TC178XED K17 VDDPF 34 11 3 2 M4 M5 VDDESB VDDESB GND CB630 100n 2 2 3 J17 VDDPF3 1 CB612 100n CB613 100n CB614 100n CB615 100n CB616 100n CB617 100n CB618 100n CB619 100n CB620 100n CB621 100n CB622 100n GND 3 1 +1V3 0R GND +3V3 +1V3 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS 6 Infineon Technologies AG TC1784/TC1387-BGA292 +3V3 8 7 8 6 of 9 ATV MC ACE PDA Number: Am Campeon 1-12 Revision: 1.1 D-85579 Neubiberg Date: 10-Jan-2011 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\Supply.sch Sheet: TriBoard BGA292 Power supply GND 0R R614 GND U101A P11 P10 P9 N12 N11 N10 N9 M14 M13 M11 M10 M8 M7 L14 L13 L12 L11 L10 L9 L8 L7 GND GND CB610 47n VDDFL3 R630 CB611 47n VDDPF3 0R R629 BAT54_opt D603 0R R613 VDDPF 7 Y20 W19 U17 T16 P12 CB631 100n D14 D13 VDDFL3 VDDFL3 8-8 VSS VSS VSS VSS VSS User’s Manual VSSP VSSP VSSP VSSP VSSP VSSP VSSP VSSP VSSP VSSP VSSP VSSP VSSP VSSP VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS Figure 8-7 A6 A11 A20 B2 B19 D4 D17 E5 E16 G1 M1 M20 Y10 Y16 G9 G10 G11 G12 H9 H10 H11 H12 J7 J8 J10 J11 J13 J14 K7 K8 K9 K10 K11 K12 K13 K14 1 A B C D TriBoard TC1784 Hardware Manual Schematic and Layout Schematic - Power Supply V 1.1, 2012-02 Figure 8-8 User’s Manual 8-9 A B C D NC1[1..80] AD[0..15] A[0..20] 1 PORT[0..10] NC3[1..80] ADC BUS..CTRL BUS EXPANSION 1 VSSM 2 +3V3 P1_12 P1_13 P1_14 NC3_77 P0_15 P10_5 P10_6 P10_7 VSSM VDDM VFAGND VAGND0 VAREF0 VSSM AN32 AN33 AN34 AN35 NC3_57 NC3_59 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 NC1_37 NC1_39 NC1_41 NC1_43 NC1_45 NC1_47 NC1_49 NC1_51 NC1_53 NC1_55 NC1_57 NC1_59 NC1_61 NC1_63 NC1_65 NC1_67 /RD /WR NC1_73 NC1_75 NC1_77 NC1_79 2 +3V3 VSSM P10_11 P10_12 P10_13 P0_14 NC3_80 P10_8 P10_9 P10_10 VSSMF VDDMF VFAREF VAGND0 VAREF1 VSSM NC3_50 NC3_52 NC3_54 NC3_56 NC3_58 NC3_60 AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 VSSM 3 NC1_6 NC1_8 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 NC1_52 NC1_54 NC1_56 /CS2 /CS1 /CS0 NC1_64 NC1_66 /BC1 /BC0 /ADV_ALE NC1_74 /WAIT NC1_78 /CS3 GND FTSH-140-02-L-DV-ES-A X703 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 FTSH-140-02-L-DV-ES-A X701 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 3 /ADV_ALE AN[0..35] 4 /ADV_ALE 4 XTAL[1..2] /ESR1_/NMI 5 5 VCC_IN GND +3V3 P0_0 P0_1 P0_2 P0_3 P0_4 P0_5 P0_6 P0_7 P0_8 P0_9 P0_10 P0_11 P0_12 P0_13 P0_14 P0_15 P1_0 P1_1 P1_2 P1_3 P1_4 P1_5 P1_6 P1_7 P1_8 P1_9 P1_10 P1_11 P4_0 P4_1 P4_2 P4_3 P5_11 P5_10 P5_9 P5_8 +3V3 VDDESB XTAL1 XTAL2 P3_0 P3_1 P3_12 P3_13 P3_2 P3_4 P3_3 P9_0 P3_10 P0_6 GND NC2_21 NC2_23 P2_8 P2_13 P6_1 P6_0 P6_3 P6_2 NC2_37 NC2_39 P3_5 P3_7 P2_8 P3_8 /ADV_ALE NC2_11 P0_5 /ESR1_/NMI NC2_17 GND 6 +3V3 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7 NC4_38 NC4_40 P9_2 P9_3 P9_4 P9_5 P9_6 P9_7 NC4_54 NC4_56 P1_4 P10_0 P10_1 P10_2 P10_3 P10_4 P5_12 P5_13 P5_14 P5_15 GND FTSH-140-02-L-DV-ES-A X704 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 P4_3 NC2_54 P3_9 P3_8 P3_14 P3_15 P2_11 P2_12 P2_10 P9_1 P3_11 P0_7 /PORST NC2_24 P2_9 NC2_28 NC2_30 NC2_32 NC2_34 NC2_36 NC2_38 P2_13 P3_6 P2_1 P2_9 P1_10 +3V3 GND GND GND NC2_10 NC2_12 NC2_14 /ESR0_/HDRST NC2_18 VCC_IN FTSH-140-02-L-DV-ES-A X702 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 6 7 GPTA / MLI Infineon Technologies AG 7 8 7 of 9 ATV MC ACE PDA Number: Am Campeon 1-12 Revision: 1.1 D-85579 Neubiberg Date: 10-Jan-2011 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\Connectm.sch Sheet: 8 TOP PERIPHERALS TriBoard BGA292 Connectors plug NC4[1..80] /PORST /ESR0_/HDRST NC2[1..80] A B C D TriBoard TC1784 Hardware Manual Schematic and Layout Schematic - Connectors (Plug) V 1.1, 2012-02 Figure 8-9 User’s Manual 8-10 A B C D NC1[1..80] AD[0..15] A[0..20] 1 PORT[0..10] NC3[1..80] ADC BUS..CTRL BUS EXPANSION 1 VSSM 2 +3V3 P1_12 P1_13 P1_14 NC3_77 P0_15 P10_5 P10_6 P10_7 VSSM VDDM VFAGND VAGND0 VAREF0 VSSM AN32 AN33 AN34 AN35 NC3_57 NC3_59 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 NC1_37 NC1_39 NC1_41 NC1_43 NC1_45 NC1_47 NC1_49 NC1_51 NC1_53 NC1_55 NC1_57 NC1_59 NC1_61 NC1_63 NC1_65 NC1_67 /RD /WR NC1_73 NC1_75 NC1_77 NC1_79 2 FLE-140-01-G-DV-A X803 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 FLE-140-01-G-DV-A X801 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 +3V3 VSSM P10_11 P10_12 P10_13 P0_14 NC3_80 P10_8 P10_9 P10_10 VSSMF VDDMF VFAREF VAGND0 VAREF1 VSSM NC3_50 NC3_52 NC3_54 NC3_56 NC3_58 NC3_60 AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 VSSM 3 NC1_6 NC1_8 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 NC1_52 NC1_54 NC1_56 /CS2 /CS1 /CS0 NC1_64 NC1_66 /BC1 /BC0 /ADV_ALE NC1_74 /WAIT NC1_78 /CS3 GND 3 /ADV_ALE AN[0..35] 4 /ADV_ALE 4 XTAL[1..2] /ESR1_/NMI 5 5 VCC_IN GND +3V3 P0_0 P0_1 P0_2 P0_3 P0_4 P0_5 P0_6 P0_7 P0_8 P0_9 P0_10 P0_11 P0_12 P0_13 P0_14 P0_15 P1_0 P1_1 P1_2 P1_3 P1_4 P1_5 P1_6 P1_7 P1_8 P1_9 P1_10 P1_11 P4_0 P4_1 P4_2 P4_3 P5_11 P5_10 P5_9 P5_8 +3V3 VDDESB XTAL1 XTAL2 P3_0 P3_1 P3_12 P3_13 P3_2 P3_4 P3_3 P9_0 P3_10 P0_6 GND NC2_21 NC2_23 P2_8 P2_13 P6_1 P6_0 P6_3 P6_2 NC2_37 NC2_39 P3_5 P3_7 P2_8 P3_8 /ADV_ALE NC2_11 P0_5 /ESR1_/NMI NC2_17 FLE-140-01-G-DV-A X804 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 FLE-140-01-G-DV-A X802 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 P4_3 NC2_54 P3_9 P3_8 P3_14 P3_15 P2_11 P2_12 P2_10 P9_1 P3_11 P0_7 /PORST NC2_24 P2_9 NC2_28 NC2_30 NC2_32 NC2_34 NC2_36 NC2_38 P2_13 P3_6 P2_1 P2_9 P1_10 6 +3V3 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7 NC4_38 NC4_40 P9_2 P9_3 P9_4 P9_5 P9_6 P9_7 NC4_54 NC4_56 P1_4 P10_0 P10_1 P10_2 P10_3 P10_4 P5_12 P5_13 P5_14 P5_15 GND +3V3 GND GND GND NC2_10 NC2_12 NC2_14 /ESR0_/HDRST NC2_18 VCC_IN GND 6 7 GPTA / MLI PERIPHERALS Infineon Technologies AG 7 8 8 of 9 ATV MC ACE PDA Number: Am Campeon 1-12 Revision: 1.1 D-85579 Neubiberg Date: 10-Jan-2011 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard BGA292 V1.1\Connectf.sch Sheet: 8 BOTTOM TriBoard BGA292 Connectors socket NC4[1..80] /PORST /ESR0_/HDRST NC2[1..80] A B C D TriBoard TC1784 Hardware Manual Schematic and Layout Schematic - Connectors (Socket) V 1.1, 2012-02 P301 P302 X601 L401 R318 X402 C401 R310 R368 CB310 R327 T302 C304 R371 C601 1 X401 D402 R326 CB315 R325 CB311 R311 R369 CB312 R323 R370 R321 R332 C611 C607 R405 R406 U402 R307 R401 R324 CB313 CB401 1 R432 R309 D403 R431 D604 X403 D501 R602 R607 R639 R608 R641 C610 R601 D605 D606 D607 R209 R439 R210 R433 R434 R511 X704 D507 D506 D505 D503 X703 XT201 U101 R515 R516 R517 R513 R514 D504 R407 D502 R512 CB203 D508 R510 CB406 1 2 3 4 5 6 7 8 R518 1 1 CB101 R114 R402 R112 R113 U104 U103 CB103 R115 CB108 R103 R403 R404 R317 R330 C303 R316 CB309 R314 R329 CB316 R315 R328 L601 R331 CB404 CB402 R408 D401 T301 R367 U302 U303 R640 R308 R313 R366 CB314 CB601 R603 R312 S601 U601 R621 C602 C604 C608 R322 R622 X301 X302 C603 X701 U106 CB102 X702 R354 R353 CB209 CB319 U203 U102 R104 CB104 8-11 C208 JP203 D204 R230 CB207 U204 R356 U306 R355 R232 C207 R117 R116 X203 R231 R228 D201 D203 CB208 R229 D202 R234 D205 S202 R227 CB204 R213 R233 R235 User’s Manual U202 8.2 X201 P401 TriBoard TC1784 Hardware Manual Schematic and Layout Layout Figure 8-10 Component Plot Top Layer V 1.1, 2012-02 X202 R105 S201 TriBoard TC1784 Hardware Manual Schematic and Layout CB206 R240 R239 C205 C211 C210 Y202 C212 R252 CB109 C209 R257 R255 C206 R259 CB205 R256 R258 R253 R254 R260 X801 U107 X802 R120 R119 R118 CB110 R121 R208 R620 1 1 R630 C202 C201 R629 CB627 R611 R225 CB202 CB620 CB606 CB607 U602 R226 Y201 R212 R610 R221 R220 R219 R203 CB613 R204 R205 C204 X804 R436 R422 U403 R421 R435 R412 1 CB408 R410 R414 R423 R416 R418 R428 R417 Q406 Q404 Q402 Q405 Q403 Q401 R427 CB407 R415 R409 R420 R424 R376 R377 U404 Y401 CB403 CB409 D609 R411 R430 CB405 U401 R429 R379 R375 R378 R372 R373 R374 Q602 R338 R440 R419 R334 R336 R335 R337 R201 R625 R340 U304 R426 R425 R333 R437 R438 R344 R626 R306 R305 CB317 R342 D608 C606 D602 D601 C609 R623 C605 Q601 R343 U305 R341 C615 R624 Q603 R627 1 R605 R609 R606 R628 R604 R616 C613 C614 R638 R319 R617 C612 R320 R619 R618 R501 R339 CB318 R202 R503 R504 X803 Q604 C203 R206 CB612 R502 R222 CB614 CB616 CB503 R614 CB626 CB618 CB619 R507 R519 R520 CB506 R509 CB501 R508 R223 CB617 CB610 CB611 CB624 CB504 CB615 CB623CB625 CB630 CB603 CB622 CB605 CB604 CB621 CB602 CB502 R506 CB505 R505 CB631 CB629 CB628 R613 D603 CB201 C616 CB609 CB608 R224 R211 R207 Figure 8-11 Component Plot Bottom Layer User’s Manual 8-12 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Schematic and Layout 8.3 Layout with Dimensioning The following dimensions should be used for development of extension boards. Note: these are the pictures from the TriBoard TC10GP. Connectors X801...X804 are on the same place. Figure 8-12 Dimensioning (mil) User’s Manual 8-13 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Schematic and Layout Figure 8-13 Dimensioning (mm) User’s Manual 8-14 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Keyword Index 9 Keyword Index This section lists a number of keywords which refer to specific details of the TriBoard TC1784 in terms of its architecture, its functional units or functions. This helps to quickly find the answer to specific questions about the TriBoard TC1784. A HWCFG 4-1 ACTIV LED 3-2 Assembly Options 4-3 I B Bus Control Signals 6-4 Bus Signals 6-4 Interrupt Signals 6-2 L DAP 3-4 DAP connector pinout 7-5 Debug Signals 6-2 Debug System 3-4 Dimensioning 8-13 Layout 8-11 LEDs 3-1 Location of general optional resistors on Bottom Side 4-4 Location of general optional resistors on Top Side 4-4 Location of memories resistors on Bottom Side 4-9 Location of memories resistors on Top Side 4-8 Location of peripheral resistors on Bottom Side 4-6 Location of peripheral resistors on Top Side 4-6 Location of resistors for safety device on Bottom Side 4-7 E M C CAN connector pinout 7-5 Clock 3-1 Clock Signals 6-2 Connector Pin Assignment 7-1 CPU clock 3-1 Crystal oscillator 3-1 D F manual reset 3-1 MiniWiggler 3-2 MultiCAN 3-3 FlexRay 3-3 Flexray Pinout 7-4 O External clock 3-1 G General optional resistors 4-3 OCDS connector pinout 7-5 OCDS1 3-4 oscillator circuit 3-1 Other peripherals 3-3 H HW Boot Configuration 4-1 User’s Manual 9-1 V 1.1, 2012-02 TriBoard TC1784 Hardware Manual Keyword Index P Peripheral Signals 6-2 Power connector pinout 7-4 Power Signals 6-1 power supply 3-1 R reset 3-1 Reset Signals 6-1 Resistors for memories 4-8 Resistors for peripherals 4-5 Resistors for safety device 4-7 Robinson Nugent 7-1 RUN LED 3-2 S Safety device Signals 6-4 Safety option 3-3 Samtec 7-1 Schematic 8-1 Schematic and Layout 8-1 Serial Connection to PC 3-2 Serial EEPROM 3-3 Serial Eeprom 3-3 Signal Description 6-1 Software 5-1 status LED 3-4 Supply 3-1 T Toggle LED’s 3-4 TriBoard BGA292 V1.1 Placement 2-4 TriBoard Software 5-1 Type of Boot TC1784 4-1 U USB Connector 3-2 USB connector pinout 7-4 User’s Manual 9-2 V 1.1, 2012-02 ((3)) http://www.infineon.com Published by Infineon Technologies AG