Download AutoMate Final.indd - Elation Professional

Auto-Mate/DMX™
Auto-Mate/DMX™
User Instructions
Features..............................................................................2
Introduction.................................................................................3
Safety Precautions......................................................................4
Connection and DMX Setup..........................................................5
Controls and Function..................................................................7
Operation (Plug and Play)...............................................................9
Installing Programs.....................................................................10
Activate the Record-Mode..........................................................11
Data Exchange...........................................................................12
Set Up Procedures
Mighty Scan.....................................................................13
Max.................................................................................14
Pocket Scan....................................................................15
X-Calibur........................................................................16
Spiral Scan......................................................................17
Rainbow 250....................................................................18
DJ Scan...........................................................................19
DJ Roller..........................................................................20
DMX Channel Settings....................................................21
Cleaning....................................................................................21
Warranty....................................................................................22
Auto-Mate/DMX™
Rev. 10/04
Elation Professional
4295 Charter Street
Los Angeles Ca. 90058
www.elationlighting.com
Contents
Features
•
•
•
•
•
•
•
•
•
256 DMX Channels
8 Chase Programs (4 x’s 2 banks)
60 Scenes per a Program
Sound Active
Blackout Mode
Built-In Microphone
19” Rackmount Design
Capable of Data Exchange
Programmable
Please Note: Specifications and improvements in the design of this
unit and this manual are subject to change without any prior written
notice.
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 2
Auto-Mate/DMX™
Unpacking
Every Auto-Mate/DMX™ has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your controller for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In case damage has been found or parts are missing, please contact our toll free customer support number for further
instructions, please do not return the controller to your dealer.
Auto-Mate/DMX™
Introduction
Introduction: The Auto-Mate/DMX™ is a Plug and Play DMX Controller with 8 programmed chases (4 slow and 4 fast). It has 256 DMX
channels and each of the 8 Chases Programs can contain up to 60
steps. This unit comes with programmed chases for either the American DJ® Spiral Scan, DJ Scan, DJ Roller, Rainbow 250, Max, Mighty
Scan, Pocket Scan, or X-Calibur. Be sure you have purchased the unit
that comes with programs for your specific fixture. All the chases are
designed to operate in conjunction with the Strobe, Fast, Slow, and
Blackout functions. You can also store your own chases on any of the
8 program banks, by using an External DMX controller such as the Elation® Show Designer.™ Storing your own programs however, will erase
any existing program that is stored in a particular memory bank.
Customer Support: Elation Profession® provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your initial set up or operation. You may
also visit us on the web at www.elationlighting.com for any comments
or suggestions. Service Hours are Monday through Friday 9:00 a.m. to
5:30 p.m. Pacific Standard Time.
Voice:
(323) 582-3322
Fax:
(323) 582-2610
E-mail:
[email protected]
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service, please contact
Elation® customer support.
Do not discard the packing carton in the trash. Please recycle
when ever possible.
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 3
Auto-Mate/DMX™
Safety Warnings
• Do not spill water or other liquids into or on to your unit.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• For adult use only - Keep out of the reach of children.
• Always use a power supply that meets the manufactures exact
power specifications
• Be sure that the local power outlet match that of the required voltage for your power supply.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Disconnect from main power before making any type of connection.
• Do not remove the unit covers under any conditions. There are no
user serviceable parts inside.
• Never operate this unit when it’s covers are removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
• Do not attempt to operate this unit, if it becomes damaged in any
way.
• This unit is intended for indoor use only, use of this product out
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer.
Auto-Mate/DMX™
Warranty Card
The Auto-Mate/DMX™ carries a two year limited warranty. We recommend you fill out the enclosed warranty card to validate your
purchase. All returned service items whether under warranty or not,
must be freight pre-paid and accompany a R.A.(return authorization)
number. If the unit is under warranty, you must provide a proof of purchase invoice. You may obtain a R.A. number by contacting customer
support.
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 4
Auto-Mate™
DMX Set Up
Auto-Mate™
DMX Set Up
POWER
POWER
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
will decrease the possibilities of erratic behavior.
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your DMX512
Elation® AutoDMX+,DMX-,COMMON
Mate/DMX™ power supply. Connect the Auto-Mate/DMX™
to a main
power supply using the included 12v AC power supply only. The Elation® Auto-Mate/DMX™ is available in a 120v and 220v version. Due
to variations in line voltage from venue to venue, be sure to plug your
power supply into a wall outlet with matching power before attempting
COMMON
to operate.
DMX512 OUT
3-PIN XLR
DMX +
1
1
DMX Data Cable (DMX Cable) Requirements: Connect the Auto-Mate/
3
3
2
2
DMX™ and your fixtures together using standard 3 pin DMX cables
(Figure 1). The Auto-Mate/DMX™ uses DMX-512 protocol to operate your fixtures. If you are constructing your
own data cables, be sure to use standard two
conductor shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
a 3-pin male and female XLR connector on either
end of the cable. Also remember that DMX lines
must be daisy chained and can not be split.
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
REMOTE
CONTROL
INPUT
Figure 1
INPUT
OUTPUT
Notice: Be sure to follow figures two and three when making your own
SOUND
SOUND
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
POWER
POWER
XLR Female Socket
XLR Male Socket
DMX512
DMX+,DMX-,COMMON
2 Cold
2 Cold
1 Ground
3 Hot
Figure 2
Pin 3 = Data True (positive)
COMMON
DMX512 OUT
3-PIN XLR
1
3
2
DMX +
DMX -
1
3
2
1
DMX512 IN
3-PIN XLR
3
2
Figure 3
©Elation
3
2
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
Auto-Mate™
DMX Addressing
DMX is short for Digital Multiplex. This is a universal binary language
used as a form of communication between intelligent fixtures. Each
dip switch represents a binary value.
SOUND
Dip Switch 1 address equals 1
DMX CHANNEL
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
2
8 32 128 SP
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
ON
Dip Switch 7 address equals 64
1 2 3 4 5 6 7 8 9 10
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
1 4 16 65 256
Dip Switch 10 address equals 512 This switch is sometimes used to activate a fixtures special func tions.
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
A DMX value (address) is set by combining the different dipswitches
that will add up to the value you wish to achieve, for example:
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
3 Hot
1
DMX512 IN
3-PIN XLR
POWER
XLR Pin Configuration
1 Ground
POWER
Setting DMX address for 21.
Flip switches 1, 3, & 5 to the
“ON” position
1 =1
Termination reduces signal errors and
avoids signal transmission problems
3=4
and interference. It is always advisable
to connect a DMX
terminal, (Resistance#
Dipswitches
5 = 16 Value
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
= 21
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 5
©Elation
Set DMX address for 201.
Flip switches 1, 4, 7, & 8 to the
“ON” position
1=1
4=8
Dipswitches # 7 = 64 Value
8 = 128
= 201
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 6
Auto-Mate/DMX™
1 2
3
4
Controls and Functions
5
6
7
8
9
Auto-Mate/DMX™
Controls and Functions
6. Audio/Prog 1 Button This button serves two functions. When the function level two is
engaged, this button will activate sound-active mode. When the function level one is engaged, selecting this button will active the program
stored in this bank.
10
7. Strobe/Prog 2 Button This button serves two functions. When the function level two is
engaged, this button will activate strobe mode. Strobe mode will initiate a strobe function to any program running. When the function level
one is engaged, selecting this button will active the program stored in
this bank.
11
12
1. Power Switch This switch turns on the unit’s main power.
2. Power Indicator This yellow LED will glow when main power is activated. This LED will
flash briefly when program mode is activated.
3. Microphone The unit comes with a built-in microphone designed to pick-up on low
frequencies. The unit then uses this signal to trigger program succession.
4. Audio Sensitivity Knob This knob is used to adjust the unit’s sensitivity to sound. When the
knob is turned in a clockwise direction, the unit becomes more sensitive to sound, when this knob is turned in a counter-clockwise direction
the unit becomes less sensitive to sound. Usually the more sensitive to
sound the unit is, the faster the programs will chase.
5. Function Button This button is used to change the functionality of the Audio/Prog 1,
Strobe/Prog 2, Fast/Prog 3, and Slow/Prog 4 Buttons. Engaging the
function button will allow the “Audio,” “Strobe,” “Fast,” and “Slow”
modes to operate. The red function LED will glow when function level
two is active.
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 7
8. Fast/Prog 3 Button This button serves two functions. When the function level two is
engaged, this button will activate the first bank of four programs. When
the function level two is engaged, selecting this button will active the
program stored in this bank.
9. Slow/Prog 4 Button This button serves two functions. When the function level two is
engaged, this button will activate the second bank of four programs.
When the function level two is engaged, selecting this button will activate the program stored in this bank.
10. Blackout Button This button activates blackout mode. In blackout mode all fixture
actively will enter into stand-by mode - No light output - No mirror
movement.
11. DMX Output Jack This jack sends the controllers DMX signal to your fixtures. This jack
uses a standard 3-pin XLR female connector.
12. Power Supply Input Jack Only connect a recommended power supply AC 9v~12v, 250mA. Use of
a power supply other than a recommend power supply could damage
your unit and will void your manufactures warranty.
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 8
Auto-Mate/DMX™
Operation
Set-Up:
Before attempting any operation, be sure you set up your system
properly. Also, be sure all DMX setting are properly adjusted. Refer to
the last pages of this manual for proper fixture positioning and DMX
channel settings that correspond with the fixtures you will be using.
If you will be customizing the Auto-Mate/DMX™ (creating your own
programs), always leave the first 4 DMX Channels (000 – 003) free, the
Auto-Mate/DMX™ needs these channels for internal instructions. All
DMX fixtures should always start on DMX a address 004.
Function Levels:
The Auto-Mate/DMX™ has two different function levels. Function level
one is the default setting and will be indicated when the red LED above
the function key is not glowing. A red LED located above the function key indicates function two. Function level one allows you access
to, and changes the four available chase programs patterns. Function
level two allows you to change the different operating modes.
Operation (Plug and Play):
When switching the Auto-Mate/DMX™ on, it will immediately enter
blackout mode. Selecting any of the four program buttons under function level one will immediately begin program playback.
Auto-Mate/DMX™
Installing Programs
Installing your own Programs:
A second way you can use the Auto-Mate/DMX™ is to store your own
programs from an external DMX Controller such as the popular Elation® Show Designer.™ These programs can then be used to automatically run your unit as the original built in program would. This operation
allows you to customize your programs to meet your individual needs.
Procedure:
First, program your desired scenes in any DMX Controller. You can
create a total of eight programs, four programs can be stored on bank
one (Fast) and four can be stored on bank two (Slow). The programs
can not consist of more than 256 DMX channels and 60 scenes or
steps.
When you have created programs, upload them Scene by Scene to
the Auto-Mate/DMX.™ When programming the Auto-Mate/DMX,™
the DMX Information for the time interval between scenes, the Strobe
function, and the Blackout function must be programmed separately.
When uploading your scenes to the Auto-Mate/DMX™ use DMX Channel 001 to set the time interval between your scenes, use DMX Channel
002 to set the strobe information in your scenes, use DMX Channel 003
to set the blackout information.
Function level 1: (Red LED Off):
Selecting any of the four PROG keys while the Function LED is not
glowing will initiate any program stored in the corresponding memory
bank. A green LED above the selected program will indicate which program is selected. When you select a new program the corresponding
green LED will begin to glow.
Function level 2: (Red LED On):
Tapping the Fast or Slow Key more than once will stop the program.
The fixtures will not blackout, but will freeze on a scene. Tapping Fast
or Slow again will continue the program from that point. This function
will be indicated when either the Fast or Slow key LED indicator is
flashing. To exit this function, deselect the fast or slow key or begin a
new program.
Blackout:
The function will stop the running program and will close the
shutters of all fixtures.
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 9
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 10
Auto-Mate/DMX™
Record Mode
Activate the Record-Mode:
In order to modify or install programs the unit must be in Record Mode.
To activate record mode:
1. While the unit is turned off, press and hold down the Function
Button (5).
2. Turn the power on while holding down the function button (5).
3. After the unit is turned on, the power LED will flash 5 times indicating record mode has been activated.
Installing the Strobe and Blackout Functions:
1. Turn on a scene via DMX with Shutter = “open”.
2. Press the Function Key until the LED goes on.
3. To store this scene press, the Strobe and Blackout Keys at the
same time. The REC. LED will come on after 3 sec.
4. Push the Blackout Key at the Master Controller. Use the same
scene you used for step 1, Shutter = “open”)
5. Press the Blackout Key at the Auto-Mate/DMX™ the REC. LED
will come on after 3 sec.
6. Switch off the master unit’s blackout function.
7. Activate the Strobe Function in the same scene. Change only the
DMX channels that activate the Strobe function.
8. Press the Strobe Key at the Auto-Mate/DMX™ Controller. After
three seconds the REC LED will temporarily glow.
Upload Scenes to the Auto-Mate/DMX™
1. Selected a program (1 through 4 ) that will hold your scene (be
sure the function LED is off).
2. With the red function indicator on, choose either Fast (1.4 second
maximum scene hold time) or slow (5.8 second maximum scene
hold time).
3. From your external DMX controller, turn on you are going to send
to the Auto-Mate/DMX.™
4. The default scene hold time is 1/10 of a second. You may
use DMX channel one on your external controller to change the
scene hold time.
- Slider value 10 is equal to one second.
- Slider value 20 is equal to two second.
- Slider value 30 is equal to three second etc...
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 11
Auto-Mate/DMX™
4.
5.
6.
Transfer Programs
Save scene into memory by pressing the Audio Key, when the
scene has been stored into memory the Rec LED will turn off.
Repeat step three and four until you have stored all your desired
scenes or you have reached the maximum of 60 scenes
Once you have completed transferring scenes from the external
controller, turn the controller off to exit
Transferring programs between two Auto-Mate/DMX™ units:
This unit allows you to transfer data from Auto-Mate/DMX™ to AutoMate/DMX™ for back-up or data swap purposes. For this procedure
you will need to construct or purchase a male to male 3-pin XLR
cable.
1. Link your two units together via the XLR connections on the rear
of each unit.
2. Set both controllers to the Record Mode, see page 11 “Activating
the Record-Mode.”
3. On the “Master” controller, the controller that will act as the
sending unit, press the Function Key (5) until the red function
LED indicator begins to glow.
4. On the “Master” controller, the sending controller unit, press
both the Fast and Slow function key at the same time. The pro
gram LEDs on both units will begin to flash and chase. This will
indicate programs are being transferred successfully.
5. The process is completed when all the program LEDs stop chasing.
If the data transfer was successful, the same program LEDs will be
glowing on both units. If the same program LED are not on, there was
an upload error. Please repeat this procedure once again.
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 12
Auto-Mate/DMX™
Mighty Scan Set Up
Auto-Mate/DMX™
Max Set Up
Max 1
ON
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
Max 2
ON
Max 3
ON
Max 4
When using only four units in your system ignore the settings and positioning for fixtures 5, 6, 7, and 8
DMX:
040
©Elation
DMX:
028
DMX:
016
DMX:
004
DMX:
010
DMX:
022
DMX:
034
ON
Max 5
ON
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
Max 6
ON
Max 7
ON
Max 8
ON
When using only four units in your system ignore the settings and positioning for fixtures 5, 6, 7, and 8
DMX:
046
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 13
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 14
Auto-Mate/DMX™
Pocket Scan Set Up
Auto-Mate/DMX™
X-Calibur Set Up
ON
X-Cal 1
1
2
3
4
5
6
7
8
9
10
ON
X-Cal 2
1
2
3
4
5
6
7
8
9
10
ON
X-Cal 3
1
2
3
4
5
6
7
8
9
10
ON
When using only four units in your system ignore the settings and positioning for fixtures 5, 6, 7, and 8
X-Cal 4
1
2
3
5
OUTPUT
6
7
8
10
X-Calibur 4
OUTPUT
OUTPUT
OUTPUT
POWER
POWER
POWER
FUSE
FUSE
FUSE
INPUT
9
X-Calibur 2
X-Calibur 1
X-Calibur 3
INPUT
4
INPUT
POWER
FUSE
INPUT
To Auto-Mate/DMX™
DMX:
012
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 15
©Elation
DMX:
004
DMX:
008
DMX:
016
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 16
Auto-Mate/DMX™
Spiral Scan Set Up
Auto-Mate/DMX™
Rainbow 250 Set Up
ON
Rainbow 1
Spiral 1
1
2
3
4
5
6
7
8
9
ON
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
10
ON
Rainbow 2
Spiral 2
1
2
3
4
5
6
7
8
9
ON
10
ON
Rainbow 3
Spiral 3
1
2
3
4
5
6
7
8
9
ON
10
ON
Rainbow 4
Spiral 4
1
DMX:
014
©Elation
2
3
4
DMX:
004
5
6
7
8
DMX:
009
9
ON
10
DMX:
008
DMX:
019
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 17
©Elation
DMX:
004
DMX:
006
DMX:
010
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 18
Auto-Mate/DMX™
DJ Scan Set Up
Auto-Mate/DMX™
DJ Roller Set Up
ON
ON
DJ Scan 1
Scan11
DJDJ
Roller
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
ON
ON
DJ Scan 2
1
2
3
4
5
6
7
8
9
Scan22
DJDJ
Roller
10
1
2
3
4
5
6
7
8
9
10
ON
ON
DJ Scan 3
Scan33
DJDJ
Roller
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
ON
ON
DJ Scan 4
Scan44
DJDJ
Roller
1
©Elation
2
3
4
5
6
7
8
9
10
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 19
1
©Elation
2
3
4
5
6
7
8
9
10
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 20
Auto-Mate/DMX™
FIXTURE
DMX Channel Setup
DMX CH. DMX CH. DMX CH. DMX CH.
ACCU SPOT 250
Ch 020
Ch 004
Ch 012
Ch 028
SPIRAL SCAN
Ch 014
Ch 004
Ch 009
Ch 019
X-CALIBUR
Ch 012
Ch 004
Ch 008
Ch 016
MIGHTY SCAN
Ch 017
Ch 005
Ch 011
Ch 023
DJ-SCAN
Ch 012
Ch 004
Ch 008
Ch 016
RAINBOW 250
Ch 008
Ch 004
Ch 008
Ch 010
MAX
Ch 068
Ch 052
Ch 060
Ch 016
ACTIVE SCAN250
Ch 016
Ch 004
Ch 010
Ch 022
ACCU SPOT 250
Ch 020
Ch 004
Ch 012
Ch 028
Auto-Mate/DMX™
Cleaning
Due to fog residue, smoke, and dust, cleaning the unit should be carried out periodically to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Use a cleaner specially designed for electronics to spray in and
around the knobs and switch. This will reduce small particle built
up that can effect the proper operation of the controller.
3. Clean should be carried out every 30-60 days.
4. Always be sure to dry all parts completely before plugging the
unit in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
Auto-Mate/DMX™
Warranty
2-YEAR LIMITED WARRANTY
A. Elation® hereby warrants, to the original purchaser, Elation® products to be free of manufacturing defects in material and workmanship for a period of 2 Years (730 days) from the
date of purchase. This warranty shall be valid only if the product is purchased within the
United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time
service is sought.
B. For warranty service, send the product only to the Elation® factory. All shipping charges
must be pre-paid. If the requested repairs or service (including parts replacement) are within
the terms of this warranty, Elation® will pay return shipping charges only to a designated
point within the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are
shipped with the product, Elation® shall have no liability whatsoever for loss of or damage
to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which Elation® concludes, after inspection, affects the reliability of
the product; if the product has been repaired or serviced by anyone other than the Elation®
factory unless prior written authorization was issued to purchaser by Elation®; if the product
is damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up. During the period specified above, Elation® will replace defective
parts at its expense, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of Elation® under
this warranty shall be limited to the repair of the product, or replacement thereof, including
parts, at the sole discretion of Elation®. All products covered by this warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E. Elation® reserves the right to make changes in design and/or improvements upon its
products without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by Elation® in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s
and or Dealer’s sole remedy shall be such repair or replacement as is expressly provided
above; and under no circumstances shall Elation® be liable for any loss or damage, direct or
consequential, arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to Elation® Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 21
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 22
MODEL: AUTO-MATE/DMX™
SPECIFICATIONS:
VOLTAGE:
WEIGHT:
FUSE:
WORKING POSITION:
PROGRAMS:
DMX CHANNELS:
POWER CONSUMPTION:
9v~12v AC
2.5 LBS / 1.5 KGS.
2 AMP GMA (INTERNAL)
ANY SAFE POSITION
8 TOTAL (2 BANKS)
60 SCENES PER A PROGRAM
256 (3 CHANNELS USED FOR
SYSTEM)
TYPICAL 2 AMPS
©Elation Professional
Elation World Headquarters:
4295 Charter Street Los Angeles, CA 90058 USA
Tel: 323-582-2650 Fax: 323-582-2610
Web: www.elationlighting.com E-mail: [email protected]
©Elation
Professional® - www.elationlighting.com - Auto-Mate/DMX™ User Manual Page 23