Download SIMPROP INTELLI CONT V3 Manual

HYPERION EOS0720iNET Layout & Sync Network Setup
CHARGER A (MASTER)
CHARGER B (SLAVE)
DC INPUT
DC INPUT
11-28V
11~28V
2X16 LCD
PC DATA
PORT
TEMP
SENSOR
PORT
OUTPUT
PORT
UP
ENTER
MODE
2X16 LCD
PC DATA
PORT
OUTPUT
PORT
UP
TEMP
SENSOR
PORT
DOWN
CHG to CHG
Network Link Port
ENTER
MODE
DOWN
Output 1~7 Cell
Lithium Balancer
Connector
CHG to CHG
Network Link Port
CHARGER to CHARGER
Optional Network Cable
#HP-EOS0610-MSC
Output 1~7 Cell
Lithium Balancer
Connector
(1) MAIN MENU FLOW
(note: whichever charger is used to select SYNC mode becomes the “master”)
MASTER
HYPERION RC
EOS0610i-Single
MEMORY
DISPLAY
MODE
DATA VIEW
DISPLAY
MODE
ENTER-2SEC
BALANCER INFOR
DISPLAY
MODE
USER SETUP
DISPLAY
MODE
ENTER-2SEC
Operation Start
DISPLAY
Balancer Start
DISPLAY
Charge Operation
DISPLAY
Balancer Operation
DISPLAY
SLAVE
MEMORY
DISPLAY
ENTER-2SEC
MODE
DATA VIEW
DISPLAY
MODE
BALANCER INFOR
DISPLAY
ENTER-2SEC
Operation Start
DISPLAY
Balancer Start
DISPLAY
Charge Operation
DISPLAY
Balancer Operation
DISPLAY
MODE
USER SETUP
DISPLAY
MODE
(2) MEMORY DISPLAY
(settings available per each memory slot, depending on battery type)
LiIo/LiPo/LiFePO4 (a123)
[ MEMORY No.0 ]
A123
9.9V
2300
ENTER
[ MEMORY No.0 ]
A123
9.9V
2300
UP
DOWN
DOWN
UP
ENTER
BATT TYPE
A123
ENTER
BATT TYPE
A123
BATT VOLTS
9.9Vpack
( 3S)
ENTER
ENTER
BATT VOLTS
9.9Vpack
( 3S)
UP
DOWN
UP
DOWN
DOWN
UP
ENTER
BATT CAPACITY
2300mAh
ENTER
BATT CAPACITY
2300mAh
UP
DOWN
DOWN
UP
ENTER
CHG CURRENT
10.0A
ENTER
CHG CURRENT
10.0A
DOWN
UP
TEMPERATURE
CUT-OFF
00`C
ENTER
ENTER
TEMPERATURE
CUT-OFF
00`C
UP
DOWN
UP
DOWN
DOWN
UP
ENTER
SAFETY TIMER
000MIN
ENTER
SAFETY TIMER
000MIN
UP
DOWN
DOWN
UP
ENTER
TCS CAPACITY
100%
ENTER
TCS CAPACITY
100%
UP
DOWN
DOWN
UP
TCS END ACTION
CONTINUE
ENTER
ENTER
TCS END ACTION
CONTINUE
UP
DSCH VOLTAGE
3.0V / CELL
ENTER
ENTER
DSCH CURRENT
1.0A
UP
DOWN
UP
DOWN
DOWN
ENTER
ENTER
DSCH VOLTAGE
13.0V / CELL
Pb
[ MEMORY No.0 ]
Pb
12.0V
40.0
BATT VOLTS
7.2Vpack
( 6S)
BATT CAPACITY
1800mAh
CHG CURRENT
1.8A
PEAK SENS.
3mV/C
TRICKLE
0mA
PEAK DELAY
3min
TEMPERATURE
CUT-OFF
50`C
SAFETY TIMER
300MIN
CHG CAPACITY
LIMITED 100%
DSCH CURRENT
1.0A
DOWN
DSCH CURRENT
1.0A
NiCd/NiMH
[ MEMORY No.0 ]
NiMh 7.2V
1800
BATT TYPE
NiMh
DOWN
UP
UP
ENTER
UP
DOWN
DSCH VOLTAGE
0.8V / CELL
BATT TYPE
Pb
BATT VOLTS
12Vpack
( 6S)
BATT CAPACITY
40.0Ah
CHG CURRENT
7.0A
TEMPERATURE
CUT-OFF
50`C
SAFETY TIMER
300MIN
DSCH CURRENT
1.0A
DSCH VOLTAGE
1.8V / CELL
(3) DATA VIEW DISPLAY
[ DATA VIEW ]
INPUT
00.000V
DOWN
(4) BALANCE INFORMATION & START DISPLAY
ENTER-2SEC
[ BALANCER
0CL 0.000V
UP
]
BALANCE START
SOLO MODE
0%
ENTER
UP
DOWN
BALANCE START
SYNC MODE
DOWN
OUTPUT 00.000V
BAT. RES 000mΩ
DOWN
UP
ENTER-2SEC
SELECT
VOLTAGE
[0CL]
00.000V
UP
**
**
DOWN
TEMP
000.0`C
PEAK.T 000.0`C
DOWN
00.000V
00.000V
CONNECTED CELLS
DOWN
00sec
DOWN
9 [xCELLS] 00.0V
UP
0.00
0.00
0.00
0.00
0.00V
0.00V
UP
CHG C. 00000mAh
PEAK.V
00.000V
DOWN
**
**
BATTERY * *
CHECK
**
UP
AVG. V
GAP V
UP
CHG TIME
000min
BATTERY * *
CHECK
**
ENTER-2SEC
The red 0%
(capacity)
above
indicates
[xCELLS] 00.0V
9 [xCELLS] 00.0V
ENTER
ENTER
Balancer Operation
DISPLAY
Balancer Operation
DISPLAY
TCS%
UP
DCHG TIME
000min
00sec
DOWN
UP
DCHG
AVR.V
00000mAh
00.000V
DOWN
UP
CYC C: 000000mAh
0] D: 000000mAh
10-second AUTO Countdown display. Starts charge
after 10 seconds if user does not confirm.
Only during Balance Charges for Li~ types.
(5) USER SETUP DISPLAY
Global Settings
[USER SETUP]
TEMP MODE
1
`C
ENTER
[USER SETUP]
TEMP MODE
ENTER
BUTTON SOUND
ON
ENTER
1
UP
`C DOWN
DOWN
UP
BUTTON SOUND
ON
1
ENTER
1
UP
DOWN
DOWN
UP
FINISH SOUND
TIME
5sec
ENTER
1
ENTER
FINISH SOUND
TIME
5sec
1
FINISH SOUND
MELODY
1
1
UP
DOWN
DOWN
UP
FINISH SOUND
MELODY 1
ENTER
1
ENTER
UP
DOWN
DOWN
UP
POWER SUPPLY 1
VOLTAGE
00.0V
ENTER
ENTER
POWER SUPPLY 1
VOLTAGE
00.0V
UP
DOWN
POWER SUPPLY 1
CURRENT
00.0A
UP
DOWN
DOWN
UP
POWER SUPPLY 1
CURRENT 00.0A
ENTER
ENTER
OPERATIONS START – SETUP & DISPLAY
(6) NiCd / NiMH BATTERY START
[ MEMORY No.0 ]
NiMh
7.2V
3300
ENTER-2SEC
MODE
CHARGE START
AUTOMATIC
ENTER
ENTER
CHARGE START
AUTOMATIC
DOWN
DOWN
UP
UP
DISCHARG START
AUTOMATIC
ENTER
ENTER
DISCHARGE START
AUTOMATIC
DOWN
DOWN
UP
CYCLE START
C>D
1T
10min
CHARGE START
NOMAL
UP
CYCLE START
C>D
1T
10min
ENTER
UP
DOWN
DOWN
UP
DISCHARGE START
NOMAL
CHARGE START
LINEAR
DOWN
ENTER
UP
CYCLE START
C>D
1T
10min
UP
DOWN
ENTER-2SEC
DISCHARGE START
LINEAR
ENTER
ENTER-2SEC
ENTER
CYCLE START
C>D
1T
10min
ENTER-2SEC
**
**
BATTERY * *
CHECK
**
OPERATION
DISPLAY
UP
DOWN
**
**
BATTERY * *
CHECK
**
OPERATION
DISPLAY
**
**
BATTERY * *
CHECK
**
OPERATION
DISPLAY
(7) LiIo / LiPo / A123 BATTERY START
[ MEMORY No.0 ]
A123
9.9V
2300
ENTER-2SEC
(8) PB BATTERY START
Selection of “No Balancer” Vs. “Solo Mode” is automatic,
[ MEM ORY No.0 ]
Pb
12.0V 45000
depending on connection (or not) to balance port.
ENTER-2SEC
MODE
MODE
CHARGE START
NO BALANCER
DOWN
UP
CHARGE START
SYNC MODE
CHARGE START
CC/CV
DOWN
DOWN
UP
STORE START
NO BALANCER
ENTER
UP
DOWN
STORE START
SOLO MODE
DOWN
UP
UP
STORE START
SYNC MODE
DISCHARGE START
LINEAR
DOWN
UP
DISCHARGE START
NO BALANCER
BATTERY * *
CHECK
**
SELECT CELLS
[0CELLS] 00.0V
ENTER
ENTER-2SEC
DISCHARGE START
SOLO MODE
ENTER-2SEC
**
**
ENTER
UP
DOWN
CHARGE START
SOLO MODE
ENTER
UP
DOWN
DISCHARGE START
SYNC MODE
ENTER-2SEC
**
**
BATTERY * *
CHECK
**
CONNECTED CELLS
9[ 0CELLS]
00.0V
ENTER
ENTER-2SEC
**
**
BATTERY * *
CHECK
**
[0CELLS] 00.0V
9 [0CELLS] 00.0V
10-second AUTO
Countdown display.
Starts charge after 10
seconds if user does not
confirm. Only during
Balance Charges for Li~
types.
**
**
BATTERY * *
CHECK
**
ENTER
OPERATION
DISPLAY
OPERATION
DISPLAY
OPERATION
DISPLAY
OPERATION
DISPLAY
Note: STORE Mode only applies to LiIo, LiPo, and LiFePO4(a123) types only. Balancer Connection is required. If Balancer is NOT connected OUTPUT BATTERY CONNECT ERROR will result.
(9) OPERATION and FINISH DISPLAY
[SOLO-RUNNING] -> SOLO mode balance
[SYNC-RUNNING] -> SYNC mode balance
[ **END** ] -> Balance complete
LiIo -> Lithium-ion battery
LiPo -> Lithium polymer battery
A123 -> Lithium Fe battery
Connected cell number
Connected Pack voltage
Connected Pack TCS
AUTO : AUTOMATIC
NORM : NORMAL
LINE: LINEAR
SOLO : SOLO MODE
SYNC : SYNC MODE
CcCv: CC-CV
C01D : CYCLE MODE
STOR : STORE MODE
If LONG UP button is pressed, each
parameter will display in 2-second rotation.
A123 SYNC 000:00
00.00A 0.000V
Output current
Output voltage
MODE
Selected cell number
cell voltage
UP
[
BALANCER ]
6CL 00.000V 0%
MODE C
0000mAh 00.0Vi
00.00V 00.00A 00%
MODE
A123 CHG 000:00
00.00A 0.000V
QUICK VIEW DATA DISPLAY
SELECT
VOLTAGE
[0CL]
00.000V
DOWN
C : Charge or
D : Discharge
mAh (charged in or discharged out)
Vi
Input (i) Voltage
V Pack Voltage,
UP
AVG. V
GAP V
00.000V
00.000V
DOWN
A Charge Current
% TCS capacity (Lithium types only.
00.00A 0.000V
CAPA.
00000mAh
INPUT 00.000V
TEMP
0.0`C
PEAK.T
0.0`C
PEAK.V
0.000V
BAT. RES 000mΩ
TCS CAP. 000%
NiCd, NiMH, PB show --%)
UP
3 68
3.62
3.62
3 70
ENTER
A123 CHG 000:00
00.00A
0.000V
UP
DOWN
DOWN
DOWN
UP
ENTER
FINISH…
3.63V
3.62V
A123 CHG 000:00
00.00A 0.000V
The decimal point changes to square
box to indicate a high cell which is
being discharged to balance
COMPLETE
00.00A 0.000V
[ MEMORY No.0 ]
A123
9.9V
2300
OFF
ENTER-2SEC
Capacity Units Displayed
NiMh, NiCd, LiPo, Liio, LiFePO4 = mAh
Pb = Ah
Output current, Output voltage
Charge capacity
Input voltage
Battery temperature
Battery peak temperature
Battery peak voltage
Battery internal resistance
TCS capacity
Finish status display
"END:DELTA-PEAK "
"COMPLETE" END
“END:CUTOFF-VOLT”
"END:TEMPERATURE"
"END:CAPACITY "
"END:TIMER
"
"END:TCS CAP.
"
(10) LiIo / LiPo / LiFePO4 (a123) FINISH DISPLAY
LiPo CHG 62:24
+ 1.00A
8.103V
LiPo SOLO 62:25
+ 1.00A
8.103V
Charge CC/CV & Discharge
Operating Display
LiPo CHG 65:32
+ 1.00A
8.103V
LiPo BLC
+ 0.20A
65:32
8.103V
Clock continues to count time until BLC is finished
Current (if any) during BLC is shown
LiPo CHG 68:40
+ 0.00A
8.400V
LiPo END
+ 0.00A
68:40
8.400V
END time should show total of CC/CV and BLC
phases
(11) NiCd/NiMH CYCLE OPERATION DISPLAY
[ MEMORY No.0 ]
NiMh
7.2V
3300
ENTER
CYCLE START
C>D
5T
10min
ENTER
**
**
BATTERY * *
CHECK
**
NiMh C01D 00:01
+ 4.00A
7.512V
NiMh C01D 09:59
+ 0.00A
8.720V
NiMh C01D 09:59
- 0.00A
6.618V
NiMh C01D 09:59
- 4.00A
8.713V
5 Cycle repeat
END:CUTOFF-VOLT
00.00A 0.000V
ERROR MESSAGES
INPUT VOLTAGE
ERROR
0.00Vi
When input voltage is below 11.0V or exceeds 28V.
OUTPUT BATTERY
CONNECT ERROR
When a battery is not connected to the charger’s output
OUTPUT BATTERY
REVERSE POLARITY
Output battery is connected to the output in reverse polarity (switch +/-)
OUTPUT BATTERY
OPEN CIRCUIT
If the battery becomes disconnected during an operation
OUTPUT CIRCUIT
ERROR
The output circuit of the charger has a problem. See troubleshooting above.
OUTPUT VOLTAGE
TOO LOW
0.00V
Output voltage is lower than the selected cells or voltages (check battery specs and condition, or reset charger correctly)
OUTPUT VOLTAGE
TOO HIGH
0.00V
Output voltage is higher than the selected cells or voltages.
TEMPERATURE
SENSOR ERROR
The thermal probe is incorrectly connected, or the probe is damaged.
BATTERY TEMP
TOO LOW
0.00V
The temperature of the battery is too low ( below -10’C at idle mode and 0’C during operation, requires probe attached!).
BATTERY TEMP
TOO HIGH
Battery temp is too high to be charged! (requires probe attached!)
INTERNAL TEMP
TOO HIGH
When the temperature of the charger exceeds 125C. Reduce ambient temp, wait, restart.
BALANCE VOLTAGE
CELL(0) TOO HIGH
When the balancing cell voltage is too high. Possible pack damage or connection error.
PAUSE...
CHARGER TOO HOT
Charger temperature is too high. Charger will Pause until temp drops
SYNC COMMAND
ERROR
Problem with wiring, connectors, or other. Clean and inspect as in Troubleshooting section for OUTPUT ERROR
FLAT CHECK
NiCd, NiMH only. Charger cannot detect DeltaV to terminate charge. See Troubleshooting section in text manual.
HARNESS WIRING FOR HYPERION-COMPATIBLE PACKS
NETII Comes with a HYPERION compatible Multi-adapter to fit 2S to 7S packs (#HP-EOSLBA-7U-B).
Other brand adapters are available as option parts, # HP-EOSLBA-7Uxx-B as below:
IF YOUR PACK MAKER IS NOT LISTED BELOW, ASK THE MAKER WHICH BRAND BELOW IT MATCHES.
HP-EOSLBA-7UXH-B
HP-EOSLBA-7U-B
HP-EOSLBA-7UTP-B
HP-EOSLBA-7UEH-B
ALIGN
HYPERION
THUNDER POWER
KOKAM
DUALSKY
POLYQUEST
FLIGHTPOWER-EVO
GRAUPNER
E-FLIGHT
E-TEC
APEX
ROBBE
ELECTRIFLY
POLY RC
VISLERO
NEU
HEXTRONIC
XCITE
DANLIONS
APOGEE
COMMON SENSE V1
MAX AMPS
MPX
VAMPOWER
COMMON SENSE V2
TRUE RC
ESKY
IMPULSE
VENOM
AIR THUNDER
KONG THUNDER
GRAYSON POWER
TENERGY
DN POWER
MEGA POWER
ELECTRIC POWER
TURBORIX
ENERGY EC, WOW RC
IMAX, FULLY MAX