Download USER MANUAL

6.
SFP Optional Modules
Nine optional SFP types provided for the Gigabit switch are
listed below:
⎯ 1000Mbps LC, MM, SFP Fiber transceiver (SFP.0LC.202)
1
3
2
4
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
16
LINK/ACT
5 7 9 11 13 15
10/100/1000Mbps
6
8 10 12 14 16
LINK/ACT
SFP
15
SFP
15
16
RESET
⎯
1000Mbps LC, SM 10km, SFP Fiber transceiver (SFP.0LC.212.10)
⎯
1000Mbps LC, SM 30km, SFP Fiber transceiver (SFP.0LC.212.30)
⎯
1000Mbps LC, SM 50km, SFP Fiber transceiver (SFP.0LC.212.50)
16
POWER
10/100/1000Mbps
⎯
Fig. 4 Front View of the 16 Port Gigabit Switch
⎯
⎯
1
3
5
7
9
11
13
15
17
19
21
3
5
7
2
4
6
8 10 12 14 16 18 20 22 24
10/100/1000Mbps
LINK/ACT
1000Mbps BiDi LC, type 2, SM 20km, SFP Fiber WDM transceiver
(SFP.0BL.621.202)
1000Mbps LC, SM 10km, SFP Fiber transceiver with DDM
(SFP.DLC.212.10)
⎯
⎯
⎯
⎯
24
RESET
24
POWER
Verify that the SFP module is the right model and
conforms to the chassis
Slide the module along the slot. Also be sure that the
module is properly seated against the slot socket or
connector
Install the media cable for network connection
Repeat the above steps, as needed, for each module to
be installed into slot(s)
Have the power ON after the above procedures are
done
10/100/1000Mbps
2
4
6
8
10
12
14
16
18
20
22
Connecting to 10/100/1000Mbps Device
Speed
Forwarding Rate
1000Mbp
s
100Mbps
10Mbps
1,488,000 PPS
148,800 PPS
14,880 PPS
• Buffer Memory : 400KB on chip frame buffer
• Flow Control: IEEE802.3x compliant for full-duplex
Backpressure flow control for half-duplex
• Switching Method : Store & forward
• Network Interface : 16/24 10/100/1000Mbps RJ-45 ports
• UTP Cable
:
TP
1000Base-SX
1000Base-LX
1000Base-LX WDM
(BiDi)
24
Fig. 5 Front View of the 24 Port Gigabit Switch
5.
• Data Transfer Rate: PPS (packets per second)
The optional SFP modules are hot swappable, so you can plug
or unplug it before or after powering on.
SFP
23
SFP
23
Installing the SFP Fiber Transceiver to
the Switch
Note: If you have no modules, please skip this section.
⎯
23
LINK/ACT
9 11 13 15 17 19 21 23
1
1000Mbps BiDi LC, type 1, SM 20km, SFP Fiber WDM transceiver
(SFP.0BL.621.201)
7.
• Diagnostic LEDs
Cat. 5 UTP cable, up to 100m
Up to 220/275/500/550m,
which depends on Multi-Mode Fiber
type
Single-Mode Fiber, up to10/30/50Km
Single-Mode Single Fiber, up to 20Km
:
System LED :
Per Port LED:
10/100/1000M TP Port 1 to 16/24
Fig. 7 Front View of 1000Base-SX/LX LC,
SFP Fiber Transceiver
1000M SFP Fiber Port
15,16/23,24
Power
: LINK/ACT,
10/100/1000Mbps
: SFP(LINK/ACT)
• Power Requirement : AC Line
Fig. 9 Installation of Optional SFP Fiber Transceiver
Fig. 8 Front View of 1000Base-LX BiDi LC,
SFP Fiber Transceiver
8.
16/24 Port Gigabit Switch Specifications
• Standards :IEEE802.3/802.3ab/802.3u/802.3x/802.3z
• Transmission : 10/100Mbps supports full or half duplex
1000Mbps supports full duplex only
• MAC Address and Self-learning : up to 8K
Note: For connecting this device to Router, Bridge, or
Fig. 6 Network Connection
5
•
•
•
•
•
•
Voltage
: 100-240V
Frequency
: 50-60Hz
Consumption
: Max. 30W
Operation Temperature : 0° to 50°C
Operation Humidity
: 10% to 90%
Storage Temperature
: 0° to 55°C
Humidity
: 5% to 95%
Dimensions: 44(H) × 442(W) × 209(D) mm
Complies with FCC Part 15 Class A, CE Mark
Approval
6
7
8