Download b - Claber

Modulo RF
User manual
Pag. 1
INSTALLATION OF RF MODULE. The RF module is fully watertight and will function even when installed permanently under water
at a depth of up to one metre (ingress protection IP68). It can be located in the open air or in a cup underground, using the bracket
provided. To ensure the control unit remains watertight, make certain that it is aligned with and fully inserted in its seat, and that the
transparent cover is securely screwed on, with the seal properly positioned in its groove. The RF Module implements the selected
watering cycles automatically by opening and closing a set of solenoid valves connected on the output side (maximum 4).
1
2
3
LO
W
a
ONLY
ALKALINE
d
ERY
BATT
BATTERY
K
O
OK!
ONLY
LINE
ALKA
max 1m
W
LO
K
O
b
ONLY
LINE
ALKA
ERY
BATT
b
BATTERY
ERY
ONLY
ALKALINE
BATT
c
OK!
ONLY
LINE
ALKA
a
D
C
B
A
For Modulo RF (cod.): 90833
RF UNIT. FITTING THE BATTERIES . To fit new batteries or replace flat ones: Unscrew the transparent cover and remove the control
unit. Unscrew the cap of the battery housing. Draw the battery holder out of the housing. Remove flat batteries, if in place, and fit
the new batteries inside the holder, observing the correct polarity. Reposition the battery holder in the housing. Retighten the cap,
checking that the seal is positioned correctly in its seat. Reposition the control unit as indicated and refit the transparent cover,
checking that the seal is correctly seated in its groove. Use only 2 new 1.5V AAA alkaline batteries. Once the batteries are fitted, an
initialization routine will take place (display Leds light up in sequence, valves close in sequence). Warning: 30 seconds after having
fitted the batteries, or pressed any of the buttons, the Leds on the panel will go out. To refresh the display, press any button.
1
2
W
LO
a
3
K
O
a
x2 AAA
Alkaline 1,5V
LOW
+
b
OK
c
W
LO
+
AA
a
LO
W
OK
OK
For Modulo RF (cod.): 90833
c
BATTERY
ONLY
ALKALINE
c
BATTERY
LOW
ONLY
ALKALINE
BATTERY
ONLY
ALKALINE
K
O
b
A
b
Close
OK
IP68
Modulo RF
User manual
Pag. 2
Synchronization of time with the Telecontroller. After replacing the batteries, proceed to synchronize the time with the Telecontroller:
take up a position with the Telecontroller no more than 10 m from the RF Module, select the number of the RF Unit (Unit1 or Unit2) to be
synchronized, using the
button of the Telecontroller. Press the RF
button of the Telecontroller and wait for the operation to be
completed.
1
2
3
W
LO
W
LO
K
O
K
O
LOW BATT
A
B
2
3
4
%
R
ER
S
EXIT
15 IT
EX
b
S
14
F
a
%
A
B A
B A
B A
T B A
W B A
T B A
F B
E
LIN
G
PRO
4
S M T W T
S
BA
TT
LO
W
AB
3
A A A A A A A 14
B B B B B B B 15
OK
M
2
1
ERR
ONLY
ALKALINE
BATTERY
LINE PROG
MAX 10m
ONLY
ALKALINE
1
BATTERY
b
OK
4
%
a
3
14
A
4
PROG
S
IT
15
S
M
O
K
ER
S
R
LIN
EX
E
IT
PROG
R
E
S
O
K
ER
LIN
B
3
2
1
BA
TT
LO
W
AB
15
EX
1
%
2
A
A B
A B
F
A B
T
A B
A B
W
T
AB B
BATT
LOW
14
A
A B
A B
F
A B
T
A B
A B
W
T
AB B
M
For Modulo RF (cod.): 90833
Procedure for association of RF Module - Telecontroller. Be sure to keep the components positioned NO MORE THAN a few metres from one another
during the association procedure. Press the 3 buttons of the RF Module simultaneously and hold for at least 5 seconds, until the CLOCK and RF
symbols turn red and start to blink (RF Module awaiting association with the Telecontroller). Press the
button of the Telecontroller immediately to
select the number of the RF Unit (Unit1 or Unit2) with which association is required. No later than one minute after the completion of step press the S1
button of the Telecontroller with the aid of a pointed object, such as a paper clip. This sets the association procedure in motion: the display of the
Telecontroller will blink to indicate that the two components are attempting to establish wireless connection (radio frequency).
3
S
EXIT
%
ERR
A A A A A A A 14
B B B B B B B 15
OK
S M T W T
F
S
EXIT
%
14
PROG
S
IT
15
EX
A
A B
A B
F
A B
T
A B
A B
W
T
AB B
BATT
LOW
S
M
a
%
14
15 IT
EX
BATTERY
LOW BATT
A
B
c
1
2
3
4
%
LINE PROG
S1
LOW BATT
A
B
=
15
EXIT
1
14
A
A B
A B
A B
A B
A B
AB B
W
T
F
AB
S
PROG
T
BATT
M
LOW
S
2
3
4
%
+
LINE
OK
ERR
LOW
OK
T
W
S
PROG
BATTERY
15
EXIT
14
A
A B
A B
A B
A B
A B
AB B
F
AB
T
BATT
M
LOW
S
1
2
3
4
%
+
LINE
OK
ONLY
ALKALINE
LOW
ONLY
ALKALINE
c
= OK
OK
ONLY
ALKALINE
R
ERR
G
PRO
ER
4
OK
E
For Modulo RF (cod.): 90833
4
4
a
BATTERY
AB
LIN
OK
3
A
B A
B A
B A
T B A
W B A
T B A
F B
BA
TT
LO
W
BATTERY
F
M
K
O
2
1
ONLY
ALKALINE
S M T W T
S
W
LO
b
LO
W
OK
3
O
K
5 sec
A A A A A A A 14
B B B B B B B 15
2
S
a
ERR
A
B
LINE PROG
%
LINE PROG
1
LOW BATT
3
4
2
3
1
2
A
1
B
A
B
E
LOW BATT
LIN
b
b
R
2
ER
1
1
2
3
4
NO
%
LINE PROG
ERR
A A A A A A A 14
B B B B B B B 15
ERR
A A A A A A A 14
B B B B B B B 15
OK
S M T W T
EXIT
OK
S M T W T
F
S
F
S
EXIT
Modulo RF
User manual
Pag. 3
Manual watering. The user can open or close a solenoid valve manually, either locally, operating from the control panel of the RF
Module, or remotely, from the Telecontroller. In the event that the panel of the RF Module is inactive, refresh the display by pressing any
one of the panel buttons. Use the or buttons to select a solenoid valve (the blink of number , , or indicates the valve
selected). Press the button to open the selected solenoid valve (when the valve is open, the symbol starts to blink and the corresponding number lights up, remaining permanently on). Press the button to close the open valve manually, or simply wait 5 minutes
and the valve will be closed automatically by the timer function.
2
a
3
W
LO
a
K
O
a
b
W
LO
OK
BATTERY
K
O
BATTERY
ONLY
ALKALINE
IP68
tested
ONLY
ALKALINE
ONLY
ALKALINE
K
W
LO
O
LOW
OK
BATTERY
1
5 min
c
b
W
LO
OK
K
O
BATTERY
ONLY
ALKALINE
LOW
c
IP68
tested
b
OK
For Modulo RF (cod.): 90833
RESET. A RESET, which restores the factory settings for the product, has the effect of clearing all watering programs and the association with the RF
Rain Sensor, whereas the association with the Telecontroller, if any, remains unaffected. To invoke the RESET, press the and buttons simultaneously and hold for 10 seconds, until the initialization cycle starts (display Leds light up in sequence, valves close in sequence).
1
a
10 sec
LO
W
BATTERY
ONLY
ALKALINE
K
O
b
Reset
For Modulo RF (cod.): 90833
For more information and further details, please consult the instruction manual supplied with the product.