Download Brisa® Fire Table Surround

Brisa® Fire Table Surround
READ ALL INSTRUCTIONS AND GAS FIRE INSERT USER MANUAL PRIOR TO ASSEMBLY.
PR OJ E CT I NSTR U CTI O NS
If considering placement on wood or composite deck, confirm weight restrictions.
Ensure area is clean and level. Know your city regulations.
MATERIALS LIST
• Purchase from another supplier
gas fire insert, control panel unit
(H), and vent panel unit (I). Other
materials may be needed for
natural gas connection.
• Tabletop
• The following Brisa® freestanding
wall system units:
6" x 16" Large (A & I)
6
6" x 10" Medium (B & H) 6
Corner/column (J)
12
Accent paver (M)
14
INSTALLATION TOOLS LIST
• Exterior-grade concrete adhesive
such as PL Premium®, SRW
landscape block adhesive or
similar product
• Caulk gun
• Tape measure
• Composite shims
NOTE: Apply dots of
glue, 1/2 inch in diameter,
roughly every 3 inches
apart before applying
next layer. Repeat
between all layers.
note position. Place vent panel with
vent facing down.
Layer 1. Starting with (J) units begin
at corner. Continue to place units
end-to-end as shown. See cutting
instruction for the vent panel unit (I),
A
J
LAYER 1
J
J
B
I
Layer 4. Place (M) accent band units
in place. Note each unit direction
and spacing (approximately 1 1/4
inch between each piece on the
long sides) required for additional
venting.
Attach vent
panel unit (I)
M
Layer 2. Starting with (J) units begin
at corner. Continue to place units
end-to-end as shown, ending with
corner units. See cutting instruction
for the control panel unit (H), note
position.
Attach control
panel unit (H)
A
Example
ASSEMBLY INSTRUCTIONS
Texture on each units faces out.
Assemble layers in the following
order:
B
J
Connect fuel source – Refer to fire
box user manual. Note additional
tools and supplies may be required.
H
J
J
LAYER 2
J
J
B
A
Layer 3. Starting with (J) units begin
at corner. Continue to place units
end-to-end as shown.
B
J
A
M
M
M
LAYER 4
Pavers 57/8” x 83/4”
M
M
M
M
M
M
CUTTING INSTRUCTION
• Vent panel unit (I). Cut a
2.5" x 11.5" section in a from a
6" x 16" large unit. Cut a 0.125"
wide by 0.5" deep notch as shown.
Face view
3.5"
6"
2.5"
4.5"
M
M
M
M
17/8"
Layer 5. Place tabletop on center of
base. Additional adhesive for minor
adjustments or a composite shim
are recommended to ensure the
top is level. Use a generous bead of
adhesive that will make consistent
contact with both the top and the
pavers. Be careful to not use too
much adhesive and immediately
clean off excess.
11.5"
3.5"
All dimensions
1
must be +
– /8"
0.125" Wide and
0.5" deep notch
• Control panel unit (H). Cut 4” from
top of 6” x 10” medium unit.
10"
4"
6"
2"
Face view
Install tray/burner, connect wires to
igniter switch and add glass beads
per supplier directions of gas insert
manufacturer.
J
LAYER 3
J
A
B
J
Control panel side shown
Custom natural stone tabletop shown
Note: Be sure to check city and county codes and home association covenants prior to installation
© 2015 Anchor Wall Systems, Inc., 5959 Baker Road, Suite 390, Minnetonka, MN, 55345
72.3987.1 10/15 4067